Small hose clamp suitable for 3/16" to 5/8" OD tubing
Go-to clamp for anywhere you need to secure tubing
Made from stainless steel
These Stainless Steel small hose clamps are perfect to keep around as your go-to clamp. Use them anywhere you want to be sure your tubing will stay connected. They are perfect for silicone hoses and hooking up quick disconnects, pumps, or on any system that may need a tight seal. These stainless clamps tighten up better than cheaper ones, and the stainless steel won’t corrode. It’s handy to keep a few spares around, just in case.
Our small clamps will fit hoses with 3/16" through 5/8" OD.
Thin walled tubing perfect for siphoning or tranferring liquids when not under pressure. This is the most common size hose for homebrewing that you would need to fit onto the plastic spigots (FE347), 3/8'' OD bottle fillers, and the 3/8'' OD racking canes.
3/8" ID, 1/2" OD
1/8" thick wall
Functions the same as a standard Hose Clamp, however rather than needing to find a screwdriver (or dime!) for every adjustment you can easily tighten by hand.
As an added bonus, this also has a significantly smoother inside to the clamp, which will not tear up your tubing nearly as much as a standard hose clamp! Ideal for situations where you need to remove tubing from fittings to sanitize.
Please note, as the reviews will also tell you, this is a clamp that will fit 1/2" OD tubing. If you are looking for a clamp for 1/2" ID (with 3/4" OD) choose the H955 clamp.
Functions the same as a standard Hose Clamp, however rather than needing to find a screwdriver (or dime!) for every adjustment you can easily tighten by hand.
As an added bonus, this also has a significantly smoother inside to the clamp, which will not tear up your tubing nearly as much as a standard hose clamp!
Ideal for situations where you need to remove tubing from fittings to sanitize.
This versatile little filter is a beer maker's insurance policy! Whether you’re aerating or racking you will appreciate having the peace-of-mind of knowing that your brew will not be contaminated by whatever is floating around in the air. Use it anywhere you need to keep something sanitary. Both 1/4"" and 3/8"" tubing will attach to it, and it will snugly fit in any standard stopper as well.
Check out this list of suggested uses:
Airlock: The most common use might be as an airlock on any kind of fermenter. Unlike other small sanitary filters, this unit fits perfectly into a stopper. Works great for conical fermenters where air is taken in when samples are taken or trub is dumped. Using the sanitary filter as airlock also eliminates the concern of drawing air back in as hot liquid cools and contracts in a fermenter. It is not appropriate for long term storage of beer as it is not an oxygen barrier.
Inline Aeration/Oxygenation Filter: With an oxygenation or aeration system, such as our FE375 or FE380, it will filter contaminants out of oxygen or air. It is connected inline between pump/O2 tank and Stainless Diffusion Stone.
Hand Pumps: Some breweries use this filter with the breweries hand pump system. Air going back into the cask is sanitized through this filter. This has extended shelf life of Real Ales by up to 2 weeks!
CO2 Filtration: Used inline with your CO2 Kegging setup, this piece can be used to filter out any potential contaminants from your CO2 Tank.
About the inline filters: There are two sides to the filter - an "in" and an "out". The direction you use doesn't matter, however, you want to take note of which way you first push air through it and always keep it that way. There is an arrow on the edge of the filter housing that we use to keep the airflow going one direction when using it. The filter should never get wet, so don't try and sanitize it by dunking it in sanitizer. If you want to clean the outside of it, use Alpet D2. To store the filter, use a little tinfoil on the "In" of the filter and store in a zip-lock bag. Can last up to 1 year. Discard if there are any signs of discoloration.
This product qualifies as a HEPA filter under US government standards.
STORE DRY AT ALL TIMES. DO NOT SANITIZE FILTER.
**NOTE: Temporarily shipping a smaller diameter unit due to supply chain issues**
Functions the same as a standard Hose Clamp, however rather than needing to find a screwdriver (or dime!) for every adjustment you can easily tighten by hand.
As an added bonus, this also has a significantly smoother inside to the clamp, which will not tear up your tubing nearly as much as a standard hose clamp!
Ideal for situations where you need to remove tubing from fittings to sanitize.
A new 5 lb CO2 tank is one of the required purchases when you’re changing over from bottling to kegging your beer.
This brand new 5 lb aluminum CO2 tank ships free in the 48 contigous states. Aluminum tanks will never rust, which is why we prefer them over steel tanks. The capacity refers to the amount of compressed (liquified) CO2 the tank can hold. 5 lbs of CO2 is enough to dispense 8 to 9 5-gallon kegs of homebrew.
All new CO2 tanks are shipped empty and will require either filling or exchanging for a full tank. Most local homebrew shops will stock gas to exchange, and many local welding supply companies can fill tanks on site.
CO2 tanks should always be stored in an upright position.
Dimensions: 14.33" Tall x 5.25" wide.
Hose clamp suitable for 3/8" to 7/8" OD tubing
Go-to clamp for anywhere you need to secure tubing
Made from stainless steel
These Stainless Steel hose clamps are perfect to keep around as your go-to clamp. Use them anywhere you want to be sure your tubing will stay connected. They are perfect for silicone hoses and hooking up quick disconnects, pumps, or on any system that may need a tight seal. These stainless clamps tighten up better than cheaper ones, and the stainless steel won’t corrode. It’s handy to keep a few spares around, just in case.
Stainless steel hose clamp will fit hoses with 3/8" through 7/8" OD.
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product.
5/16 inch ID tubing is recomended for use with Mini and Regular Auto Siphons.
Thin wall tubing is recomended for siphoning and transferring liquids. For pumping, keg lines, or other pressurized applications, see our thick wall and keg tubing.
Allows for easy and efficient gas transfers, ensuring minimal oxygen exposure and preserving the delicate flavors and aromas of your barrel-aged creations!
Stainless lock down mechanism to adjust height
Compression Silicone Bung to form airtight seal with barrel
Adjustable lees pin
Transfer wine out of a barrel using inert gas to reduce oxidization with our Gas Transfer Tool. After using most all similar tools on themarket, we took what we liked and disliked and made our own. Obviously we love the price!... but perhaps more impressive is the polished finish and the excellent quality welds. We sell it without a sight-gauge welded in or attached. We found it easier to clean without a welded in place sight-gauge. We also found that most wineries already had other sight-gauges in the winery and did not need it included. Of course it is available as an option, (sight-gauge H664, clamp H652, gasket, h656.) Replacement gaskets and parts in stock and available.
Quality Features
Stainless lock down mechanism to adjust height
Polished stainless tube
Compression Silicone Bung to form airtight seal with barrel
Adjustable lees pin
Made from 304 stainless steel
Specifications
1.5" Tri-Clover Outlet
1/4" Stainless Steel Ball Valve with FPT inlet for inert gas
31" height from lees pin to pictured stopper
Starts siphon with a single stroke
Made from BPA-free acrylic plastic
Includes anti-sediment tip
Easy to dissasemble for cleaning and drying
7/8" outer diameter fits glass carboys, 1-gallon jugs or Growlers
The name says it all! No more struggling with all the different techniques to get a siphon started. The Easy-Siphon will get your transfer started quickly and with zero fuss. Simply submerge the the siphon, pull the inner tube up about halfway, then pump down to start the siphon. New design features 7/8" OD racking tube to better fit carboys, 1-gallon jugs, or growlers.
To prolong the life of your Easy Siphon, make sure that every time you assemble the unit, the inner walls of the outside acrylic tube and the O-Ring are wet.
Comes with 3/8" cane and 24" racking tube. 5/16" or 3/8" ID tubing must be purchased separately. Also available in 1/2" and 3/8" Mini models.
Maximum Temperature: 140°F (60°C)
Instructions:
Sanitize and rinse your Easy-Siphon.
Get the inner tube gasket and the outer tube wet.
Attach the curved siphon to a hose.
Submerge the end of Easy-Siphon into your container.
If bottling directly, attach the correct bottle for the tubing you are using and place it inside your bottle wand. Otherwise place the the tubing into the container you're racking to.
Pull the inner tube up about 7" until the liquid fills the tube.
Pump the inner tube down and siphon will begin.
Pull out inner tube and sanitize Easy-Siphon for storage.
This product is not resistant to high levels of alcohol. Do not sanitize with alcohol.
Acrylic is safe for long exposure to ABV up to 15%. It is safe up to 30% ABV for short periods of time (10 minutes or so). Not safe to expose acrylic to more than 30% ABV. Exceeding those limits will damage the Acrylic and could potentially leach into liquid. If you need to exceed these limits, we recommend using a stainless racking cane.
Getting a siphon started can be one of the biggest hassles that homebrewers face. There are endless methods you can try that usually end in a siphoning disaster. If this sounds familiar you will LOVE this Sterile Siphon Starter! No sucking the end of the tube, no plungers with faulty gaskets, no shaking, no filling up the tube with unsterilized water, nothing to break, no contamination, no disturbing the sediment, and no fuss!
Simply blow into the sterile filter, which slightly pressurizes the carboy, forcing beer to flow up the racking cane and out the tubing, thus starting your siphon. This is hands down superior to the numerous other methods of starting a siphon (and we have tried them all!)
This size will also work for larger-mouthed plastic carboys!
How to Use: Attach the Sterile Siphon starter assembly by firmly pushing the carboy hood over the mouth of the carboy. Slide the stainless racking cane to the desired depth, just about the sediment level and blow into the white, sanitary air filter for 2-3 seconds until you have a solid flow of beer running out the tubing. There is no need to worry about contamination from your mouth, as the sanitary filter removes 99.98% of airborne bacteria.
Sterile Siphon Includes:
26 inch Stainless Racking Cane
Red Sediment Reduction Tip
Rubber Carboy Blowoff Hood w/White Caps (Fits 3, 5, 6, 6.5 Gallon smooth neck glass carboys; see R552 if you have the more common Italian 6.5 gallon carboy with threads)
5' of 3/8" ID Vinyl Tubing
Stainless Hose Clamp
Sterile Air Filter
About the White Sterile Filter: There are two sides to the filter - an "in" and an "out". The direction you use doesn't matter, however, you want to take note of which way you first push air through it and always keep it that way. There is an arrow on the edge of the filter housing that we use to keep the airflow going one direction when using it. The filter should never get wet, so don't try and sanitize it by dunking it in sanitizer. If you want to clean the outside of it, use Alpet D2. To store the filter, use a little tinfoil on the ""In"" of the filter and store in a zip-lock bag.
STORE DRY AT ALL TIMES. DO NOT SANITIZE FILTER.
Starts siphon with a single stroke
Made from BPA-free acrylic plastic
Includes anti-sediment tip
Easy to dissasemble for cleaning and drying
7/8" outer diameter fits glass carboys, 1-gallon jugs or Growlers
The name says it all! No more struggling with all the different techniques to get a siphon started. The Easy-Siphon will get your transfer started quickly and with zero fuss. Simply submerge the the siphon, pull the inner tube up about halfway, then pump down to start the siphon. New design features 7/8" OD racking tube to better fit carboys, 1-gallon jugs, or growlers.
To prolong the life of your Easy Siphon, make sure that every time you assemble the unit, the inner walls of the outside acrylic tube and the O-Ring are wet.
Comes with 1/2" cane and 24" racking tube. 7/16" or 1/2" ID tubing must be purchased separately. Also available in 3/8" and 3/8" Mini models.
Maximum Temperature: 140°F (60°C)
Instructions:
Sanitize and rinse your Easy-Siphon.
Get the inner tube gasket and the outer tube wet.
Attach the curved siphon to a hose.
Submerge the end of Easy-Siphon into your container.
If bottling directly, attach the correct bottle for the tubing you are using and place it inside your bottle wand. Otherwise place the the tubing into the container you're racking to.
Pull the inner tube up about 7" until the liquid fills the tube.
Pump the inner tube down and siphon will begin.
Pull out inner tube and sanitize Easy-Siphon for storage.
This product is not resistant to high levels of alcohol. Do not sanitize with alcohol.
Acrylic is safe for long exposure to ABV up to 15%. It is safe up to 30% ABV for short periods of time (10 minutes or so). Not safe to expose acrylic to more than 30% ABV. Exceeding those limits will damage the Acrylic and could potentially leach into liquid. If you need to exceed these limits, we recommend using a stainless racking cane.
Get that eye-catching cascading effect by serving your Stouts & Porters with a nitrogen tank filled with beer gas mix!
Serve still beverages on draft with pure nitrogen or argon—serving still bevs with CO2 will lead to carbonation over time
Dual high-pressure and low-pressure gauges to easily reference cylinder pressure and output pressure
CGA580 inlet compatible with standard US nitrogen and argon tanks
Made in the USA. Taprite is one of leading manufacturers of gas regulators and draft dispensing equipment
One-way shutoff valve outlet protects your regulator from backflow and can be turned on/off to stop gas flow without needing to close your tank
This Taprite Nitrogen Regulator will allow you to add Nitro-Draft capability to your home dispense system!
Use this dual gauge nitrogen regulator to connect a tank of Beer Gas mix (70% Nitorgen/30% CO2) to your keg for an authentic nitro-pour! Traditionally used for stouts and porters, a nitro pour is becoming popular with more and more beer styles, lending its signature creamy mouthfeel and head to the beer. An amazing upgrade to any brewer's draft system.
Made in the USA by Taprite. 5/16" barb.
Transfer beer or wine between vessels without the hassle of starting a siphon
Place your receiving vessel side-by-side or even above the transferring vessel
Perfect for transferring between primary and secondary fermenter, or from fermenter to bottling bucket or keg
Eliminate excess oxygen exposure caused by hand-pumping or blowing into a carboy hood to start a siphon
The Super Sucker transfer pump is the quickest, most hassle-free solution to moving beer or wine between vessels. Rack from primary fermenter to secondary or from carboy to keg without the excess oxygen exposure that results from hand-pumping a siphon or blowing into a carboy hood. Simply run transfer tubing from a racking cane to the pump and then to your receiving vessel, flip the switch, and let the Super Sucker do the work while you kick back and enjoy a cold beverage.
With the Super Sucker you don't need gravity or CO2 pressure to move liquid around. Thanks to the pump's considerable max lift height, you can leave your heavy, full fermenter on the ground and place the receiving keg or carboy side-by-side or even above the fermenter on a countertop.
The 10 mm barbed inlet and outlet are perfect for use with 3/8" ID tubing. We recommend using our Racking Cane Siphon Kit plus 5 ft. of 3/8" vinyl tubing. Secure pump connections with butterfly hose clamps for easy set up and break down.
Features:
Self-Priming
10 mm Barbed Inlet/Outlet
On/Off Switch
Max Flow: 1.12 Gal/min
Suction: 5 in.
Max Lift: 150 in. (12.5 ft.)
Maximum Temperature: 140°F
Pressure: 90 psi
Voltage: 12V DC (3.5A)
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product.
7/16 inch ID tubing is recomended for use with 1/2 inch Auto Siphons.
Thin wall tubing is recomended for siphoning and transferring liquids. For pumping, keg lines, or other pressurized applications, see our thick wall and keg tubing.
The perfect pump for use after fermentation! Self-priming and easy to use for transfers between carboys or kegs
Included pre-filter removes solids from your liquid and features a quick disconnect design to easily remove the filter for cleaning
Adjustable flow rate from 0 to 3 gallons for gentle transfers and slowly pushing finished beer through plate filters
Diaphragm pumps are gentle on the liquid passing through them with much less turbulence and aeration compared to magnetic drive pumps
The Vintage Shop has been a pioneer in the manufacturing of products for the home wine and beer industry since 1969
Includes tubing and clamps—ready to use out of the box!
Why This is a Great Pump:
Self-Priming
Heat Tolerant materials to 212°F when used with Silicone tubing
Speed Control!
Gentle Diaphragm Design
Self Priming: This pump is capable of pumping gasses, meaning that pumping does not require priming! This makes transfers between carboys or kegs incredibly easy. Simply put both inlet and outlet hoses in a bucket of sanitizer and run the pump for a minute. You're then good to transfer your beer with your sanitized pump!
Removable Pre-Filter: This is something which is almost always necessary on diaphragm pumps, as the diaphragm itself is very delicate, and can be ruined by small solids. The pre-filter included on this pump will work to keep solids out of the pump, extending the working life of the unit. And the filter can be removed between uses for cleaning.
Heat Tolerant: All materials used in the construction of the pump tolerate temperatures up to 212°F when used with heat tolerant tubing such as silicone. Because the pump comes with vinyl tubing you would need to replace that tubing with silicone.
Speed Control: Perhaps the most unique feature is a dial control to adjust flow from 0 to 3 gallons per minute. Use it to send your wort from the kettle to the fermenter, or even after fermentation to send beer through a plate filter (such as our FIL45).
Gentle on your Beer: A diaphragm pump works by moving beer through one pulsating diaphragm into the next. It is a design that is very gentle on the liquid being pumped.
When this pump was first introduced to us, we loved the idea, but had concerns that the speed control would compromise the longevity of the motor. We've built much larger pumps and normally you need a $700 frequency drive to control motor speed. However, we've been selling this pump since the mid-2000s and it continues to perform well and receive excellent customer feedback.
This pump comes with 1/2" barbed ports for easy connectivity
Comes with 4' tubing on both sides
Heat Tolerant materials to 212°F (when used with silicone tubing)
110 Volts, 0.5 Amp, 60 Hz.
Perfect size for siphoning or bottling from a gallon jug. Takes 5/16" tubing (see YMAN section below).
Instructions:
Sanitize and rinse your Auto Siphon.
Get the inner tube gasket and the outer tube wet.
Attach the curved siphon to a hose.
Submerge the end of Auto Siphon into your container.
If bottling directly, attach the correct bottle for the tubing you are using and place it inside your bottle wand. Otherwise place the the tubing into the container you're racking to.
Pull the inner tube up until the liquid fills the tube.
Pump the inner tube down and siphon will begin.
Pull out the inner tube and sanitize your Auto Siphon for storage.
Our standard 1/2" racking cane tips will work with this product, see our You Might Also Need section below for product information.
Siphon starter for transferring liquids and bottling. Very easy to use and sanitize. A single stroke starts the siphon without disturbing the sediment. Precision designed for smooth, leak-free operation.
The Regular Auto Siphon is recommended for use with standard buckets and carboys. We strongly recommend you use 5/16 in ID tubing (not 3/8 in) to prevent air leaks from stopping the siphon. Outer diameter of the siphon shaft is 7/8 inches.
Includes everything you need to start using the Super Sucker right out of the box!
Transfer beer or wine between vessels without the hassle of starting a siphon
Place your receiving vessel side-by-side or even above the transferring vessel
Perfect for transferring between primary and secondary fermenter, or from fermenter to bottling bucket or keg
Eliminate excess oxygen exposure caused by hand-pumping or blowing into a carboy hood to start a siphon
The Super Sucker transfer pump is the quickest, most hassle-free solution to moving beer or wine between vessels. Rack from primary fermenter to secondary or from carboy to keg without the excess oxygen exposure that results from hand-pumping a siphon or blowing into a carboy hood. Simply run transfer tubing from a racking cane to the pump and then to your receiving vessel, flip the switch, and let the Super Sucker do the work while you kick back and enjoy a cold beverage.
With the Super Sucker you don't need gravity or CO2 pressure to move liquid around. Thanks to the pump's considerable max lift height, you can leave your heavy, full fermenter on the ground and place the receiving keg or carboy side-by-side or even above the fermenter on a countertop.
The Racking Cane Kit includes stainless steel racking cane, two 5 ft. lengths of vinyl transfer tubing, and two butterfly hose clamps for pump connections.
Super Sucker Features:
Self-Priming
10 mm Barbed Inlet/Outlet
On/Off Switch
Max Flow: 1.12 Gal/min
Suction: 5 in.
Max Lift: 150 in. (12.5 ft.)
Maximum Temperature: 140°F
Pressure: 90 psi
Voltage: 12V DC (3.5A)
Racking Cane Kit Includes:
3/8" OD Stainless Racking Cane (26" long)
2 x 5 ft. lengths of tubing (3/8" ID)
2 x Butterfly hose clamps
Racking cane clip
Leave the gunk behind and keep your beer clear with this racking cane filter. A great solution at the right price.
This Racking Cane Filter Screen is very effective when racking with whole hops, oak, or fruit in the fermenter. Simply slide this over the bottom of the racking cane and begin the siphon! Made from Stainless Steel mesh. Some customer are also using this in the their keg attached to the bev out dip tube.
Fits on a 3/8" stainless steel racking cane.
Note: You may want to use a hose clamp to tighten this to the racking cane.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in late December.
With your own Nitrogen tank, you can add Nitro-Draft capability to your Home Dispense System!
Serve beer on Nitro! The best way to pour your favorite stouts and porters!
Made from high-quality aluminum that will never rust like steel tanks
Fill with Beer Gas Mix to get that alluring, cascading pour famously associated with Guinness
CGA580 valve pairs with standard US-style nitrogen & argon gas regulators
KOMOS® offers a full suite of first-rate draft products and draft fittings—from kegs to faucets and everything in between!
Use pure nitrogen to serve still wine, cold brew coffee, Sangria and premixed cocktails on draft
Brand new aluminum 22 cubic feet Nitrogen tank made from high strength aluminum alloy and high quality CGA580 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It can be filled with compressed (liquified) Nitrogen, Argon, or Beer Gas Mix (70% Nitro/30% CO2).
Fill with beer gas mix (70% Nitrogen/30% CO2) for dispensing beers "On Nitro". Using 100% Nitrogen is also the recommended gas for dispensing cold brew coffee, wine, or even Sangria and premixed cocktails on draft!
Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder.
Tanks should always be stored in an upright position.
Features:
Made from corrosion resistant, engineered Aluminum
Brushed finish
Thick, durable cylinder walls
DOT approved
New high quality CGA-580 valve
Light weight compared to steel tanks
Rated to 2216 PSI service / 3360 PSI test pressure PSI (allowing for Nitrogen fill)
Can also be filled with Argon or Beer Gas Mix (Nitrogen/CO2)
NOTE: You will need at Nitrogen/Argon Regulator to go with this tank, a standard CO2 regulator will not work.
The Easy Siphon Clip holds your Easy Siphons to Carboys, Pails, Fermonsters, Buckets and more! Made from lasting plastic materials, so you can clip and unclip your Easy Siphons without issues.
Works with:
Easy Siphon 3/8" & 1/2" (R511 / R513)
2022 models - 7/8" thick
Mini Easy Siphon
The Sample Taker (MT342)
Legacy Easy Siphon 3/8" & 1/2" (R510 / R512)
pre-2022 Models - 1" thick
Please note: if the clip is used with the Legacy Easy Siphons (pre-2022 models), it will not work with the new models afterwards as the clamps will stretch to adapt to the bigger diameter of the older models.
Ideal for racking in and out of barrels, or any other medium-sized vessels without a bottom valve. The built-in Sediment Pin allows you to set how far from the bottom of the vessel you want the wand to draw from. Side draw ports help pull in beer without drawing sediment. Durble, easy to clean stainless steel construction.
Specifications:
AISI304 Stainless Steel construction
30" Long straight (usable) portion of racking cane
1" Diameter Tubing
1.5" Tri-Clamp Connection
Transfer fermented, but uncarbonated, beer from carboy to carboy or from carboy to keg. For those brewers that perhaps cannot lift a carboy or have issues with siphoning this is a great solution. Self-priming (will push air) so that it can draw out of a carboy or tank. Gentle diaphragm action so as to not "beat up" the beer. Made of food-grade, NSF approved, materials polypropylene and santoprene, so no metallic interaction with the product. Pumps 3 gallons per minute.
Flow can be restricted with an inline valve positioned on the outflow side. Self-regulating motor is designed to temporarily shut down, and then turn back on, when restriction pressure exceeds pump capacity. Has a heat limitation of 125 degrees Fahrenheit so cannot be used in brewing applications.
Shurflo brand pump is equipped with 1/2" Male NPT posts on the inlet and outlet. Does not include the plastic barb fittings you will need to purchase separately. Please see the "You Might Also Need" section below for our recommendations regarding which fittings to attach to the pump.
Technical Specifications
PUMP DESIGN: Positive Displacement 3 Chamber Diaphragm Pump
CHECK VALVE: (1-Way Operation) Prevents Reverse Flow
CAM: 3.0 Degree
MOTOR: Permanent Magnet, P/N 11-195-01, Thermally Protected
VOLTAGE: 115 VAC Nominal
PRESSURE SWITCH: Factory Set @ 45 PSI Shut-Off, Turn On 25 5 PSI
LIQUID TEMPERATURE: 130 Degrees Fahrenheit (54 Degrees Centigrade) Max.
PRIME: Self-Priming Up To 9.0 Ft. Vertical, Max. Inlet Pressure 30 PSI (2.1 Bar)
PORTS: 1/2" - 14 Male Parallel Thread
Materials:
PLASTICS- Polypropylene
VALVES- Santoprene
DIAPHRAGM - Santoprene
FASTENERS- Zinc Plated Steel
NET WEIGHT: 5.3 Lbs (2.4 Kg)
APPROVALS: UL, C-UL Listed, N.S.F. Listed
Clear plastic racking cane with curve. Good for 6.5 gallon carboys. 3/8" diameter is the standard size for filling beer bottles.
3/8" OD
30" total length (including bend)
27" from tip to bend
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product.
Thick wall tubing is recomended for pumping and pressurized systems. For siphoning and transferring liquids, see our thin wall and transfer tubing.
Siphon starter for transferring liquids and bottling. Very easy to use and sanitize. A single stroke starts the siphon without disturbing the sediment. Precision designed for smooth, leak-free operation.
The Large Auto Siphon is recomended for use with standard buckets and carboys. We strongly recomend you use 7/16 in ID tubing (not 1/2 in) to prevent air leaks from stopping the siphon.
Used to clean the inside of tubing using a pump. Place in the line, hook up to the outlet of the pump and push through the line. Be careful not to suck into the pump head! Available in sizes for 1/2", 1", 1.5" and 2.5" inner diameter tubing.
Getting a siphon started can be one of the biggest hassles that homebrewers face. There are endless methods you can try that usually end in a siphoning disaster. If this sounds familiar you will LOVE this Sterile Siphon Starter! No sucking the end of the tube, no plungers with faulty gaskets, no shaking, no filling up the tube with unsterilized water, nothing to break, no contamination, no disturbing the sediment, and no fuss!
Simply blow into the sterile filter, which slightly pressurizes the carboy, forcing beer to flow up the racking cane and out the tubing, thus starting your siphon. This is hands down superior to the numerous other methods of starting a siphon (and we have tried them all!)
This size will also work for larger-mouthed plastic carboys!
How to Use: Attach the Sterile Siphon starter assembly by firmly pushing the carboy hood over the mouth of the carboy. Slide the stainless racking cane to the desired depth, just about the sediment level and blow into the white, sanitary air filter for 2-3 seconds until you have a solid flow of beer running out the tubing. There is no need to worry about contamination from your mouth, as the sanitary filter removes 99.98% of airborne bacteria.
Sterile Siphon Includes:
26 inch Stainless Racking Cane
Red Sediment Reduction Tip
Rubber Carboy Blowoff Hood for 6.5 Gallon Carboy with threaded neck
5' of 3/8" ID Vinyl Tubing
Stainless Hose Clamp
Sterile Air Filter
About the White Sterile Filter: There are two sides to the filter - an "in" and an "out". The direction you use doesn't matter, however, you want to take note of which way you first push air through it and always keep it that way. There is an arrow on the edge of the filter housing that we use to keep the airflow going one direction when using it. The filter should never get wet, so don't try and sanitize it by dunking it in sanitizer. If you want to clean the outside of it, use Alpet D2. To store the filter, use a little tinfoil on the ""In"" of the filter and store in a zip-lock bag.
STORE DRY AT ALL TIMES. DO NOT SANITIZE FILTER.
Note: The color of the hood you recieve may vary from the hood that is pictured.
This white plastic swivel fitting is made by Shurflo, manufacturers of our popular H305 Self Priming Diaphragm pump, and is designed specifically to fit with this pump. Features a 1/2" Barb x 1/2" Female Thread swivel fitting, which makes disconnecting your hoses from the pump a snap. Made from NSF Food Grade polypropylene.
