Starts siphon with a single stroke
Made from BPA-free acrylic plastic
Includes anti-sediment tip
Easy to dissasemble for cleaning and drying
7/8" outer diameter fits glass carboys, 1-gallon jugs or Growlers
Mini Easy Siphon will reduce loss when racking from small vessels
The name says it all! No more struggling with all the different techniques to get a siphon started. The Easy-Siphon will get your transfer started quickly and with zero fuss. Simply submerge the the siphon, pull the inner tube up about halfway, then pump down to start the siphon. New design features 7/8" OD racking tube to better fit carboys, 1-gallon jugs, or growlers.
To prolong the life of your Easy Siphon, make sure that every time you assemble the unit, the inner walls of the outside acrylic tube and the O-Ring are wet.
Comes with 3/8" cane and 15" racking tube. 5/16" or 3/8" ID tubing must be purchased separately.
Maximum Temperature: 140°F (60°C)
Instructions:
Sanitize and rinse your Easy-Siphon.
Get the inner tube gasket and the outer tube wet.
Attach the curved siphon to a hose.
Submerge the end of Easy-Siphon into your container.
If bottling directly, attach the correct bottle for the tubing you are using and place it inside your bottle wand. Otherwise place the the tubing into the container you're racking to.
Pull the inner tube up about 7" until the liquid fills the tube.
Pump the inner tube down and siphon will begin.
Pull out inner tube and sanitize Easy-Siphon for storage.
This product is not resistant to high levels of alcohol. Do not sanitize with alcohol.
Acrylic is safe for long exposure to ABV up to 15%. It is safe up to 30% ABV for short periods of time (10 minutes or so). Not safe to expose acrylic to more than 30% ABV. Exceeding those limits will damage the Acrylic and could potentially leach into liquid. If you need to exceed these limits, we recommend using a stainless racking cane.
Prevent electrocution! This is the best way to plug in a pump or other brewing or winemaking equipment because it will trip the circuit when any water flows on the ground wire. 15 Amps 1875 Watts 125 VAC 60 Hz.
A replacement pump head for the H308 diaphragm pump, should the diaphragms become worn or get damaged by passing particulate matter through them.
Please Note: This pump head does not include the Pre-Filter or the Elbow fittings that are connected to your hoses, those will need to be transferred over from the existing pump head or purchased separately.
Transfer the clearest beer possible from first pint to last with the Super Sucker Filtered Racking Buoy! Stainless steel float allows you to pull liquid from the top of your vessel rather than transferring out from the bottom Sediment falls out of suspension over time, especially at cold temperatures, so the clearest beer is always at the top! 10 feet of tubing can be cut to your preferred length for both the pump inlet and outlet Made for use with the Super Sucker Transfer Pump The Filtered Racking Buoy kit allows you to transfer the clearest liquid possible with the Super Sucker Transfer Pump. Whether you're transferring beer or wine, the clearest liquid will always be at the top of the vessel as solids fall out of suspension and settle to the bottom over time. The stainless steel float will position your transfer tubing at the top of the liquid so you can pull from the top down and cease transferring when you get near the sediment. The filter attachment will add a layer of protection for the pump and will leave solids behind in your fermenter or storage tank. Includes: Stainless float (1.75" Ø) Filter attachment 10' length of 3/8" ID silicone tubing (3) hose clamps
The redesigned quick disconnect pre-filter for the H308 Super Transfer pump now features a replaceable filter screen. Pick up a replacement or keep a spare on hand. When your filter mesh screen is past its prime, simply replace the screen rather than replace the whole pre-filter. Please note: this filter screen will only work with the current generation pre-filter. If you purchased the Super Transfer pump before 2020 and have the original pre-filter, you will need to upgrade to the newest version (H308C) to be compatible with this replacement mesh screen.
Digital flow-meter perfect for winemaking, beer making, cider making and more. Equipped with reset function, a cumulative totalizer reset, and a non-resettable totalizer. Calibration function to adapt the instrument to fill by gravity, or to fill with transfer pumps.
Features:
Capacity from 30L/7.9G to 130L/34.3G per minute
Display changeable from liters to gallons
Minimum pressure 0,3 bar, maximum pressure 16 ba
1" BSPP (straight thread) outlets (includes 1" barbs)
Accuracy + -1% of indicated value after calibration
Repeatability + – 0.3%
Battery Powered
Rated to a maximum temperature of 85 C°(185 f°)
The 50C rating in the manual is a typo.
Heavy-duty hose clamp suitable for 1-1/4" to 2-1/8" OD tubing
Effective and removable
Easily adjusted with a flathead screwdriver
Made from stainless steel
A heavy duty hose clamp for large OD tubing. As effective as a pre-formed clamp but without the expense or permanence.
Replacement elbow fitting for the H308 diaphragm pump. This fitting is typically only used on the pump outlet, but can also be placed on the inlet in lieu of the Pre-Filter. Please note that doing so puts the pump head at increased risk of damage from particulate matter.
Kink and crush resistant suction & discharge rubber hose, designed for demanding applications that require high temperature and chemical resistance ForgeFit barbed connector and crimp sleeve system are designed to provide a long life and easy to clean hose connection Hose barb skips the first barb to provide a gapless and smooth transition to the tubing Our sleeves are machined from pipe to meet sanitary standards, avoiding the uneven compression and hard points caused by welding, and offering a superior surface finish that is both more hygienic and visually appealing Novaflex Connoisseurs Beverage Hose Meets 3-A (cert# 1803), FDA & USDA standards Tubing sets made from ForgeFit fittings and Novaflex Connoisseurs food & beverage tubing that are assembled in the MoreBeer! Pro metal shop in Pittsburg, California. The options above are already assembled and ready to ship. If these options do not suit your needs, custom lengths can also be made to order. Novaflex is a special kink and crush resistant suction & discharge rubber hose, designed for those more demanding applications requiring a product that meets 3-A (cert# 1803), FDA & USDA standards. This tube is for non-oily applications. Designed to meet the temperatures and chemical resistance associated with “cleaning in place” systems. This ultra smooth microbe resistant tube is built on special stainless steel mandrels for cleanliness. The ForgeFit barbed connector and crimp sleeve system is designed to provide a long life and easy to clean hose connection. The long barb and the long sleeve provide a secure crimp without crushing the hose. Triple banding can slip or damage the hose during installation and has sharp edges. The ForgeFit® hose barb skips the first barb to provide a gapless and smooth transition to the tubing to make it easier to keep clean. Our barb has a stop to ensure the hose does not creep closer to the clamp in service. Don't forget to add hose bumpers to your order to protect your investment! The ForgeFit® Silicone Hose Bumper is designed to protect your hose ends by absorbing the impact of the hose end hitting the floor when it's dropped. The unique built in handle makes it easier to grab and saves your back. Novaflex Construction: Tube: White Chlorobutyl Reinforcement: Multiple plies of polyester tire cord & dual monofilament helix Cover: Gray EPDM abrasion resistant Temperature Range: -40° to 240°F (CIP to 248°F) Not for continuous steam service in. mm ID 1.5 38.1 OD 2.14 54.35 Bend Radius 4.5 114
Due to high demand, some of these items are currently out of stock but available for pre-order. Please check status notes below when selecting a size option to see if it is In Stock or tagged as PreBook. We will automatically ship this to you when we receive more inventory. Kink and crush resistant suction & discharge rubber hose, designed for demanding applications that require high temperature and chemical resistance ForgeFit barbed connector and crimp sleeve system are designed to provide a long life and easy to clean hose connection Hose barb skips the first barb to provide a gapless and smooth transition to the tubing Our sleeves are machined from pipe to meet sanitary standards, avoiding the uneven compression and hard points caused by welding, and offering a superior surface finish that is both more hygienic and visually appealing 1" ID tubing is sometimes preferred to 1.5" as it is easier to handle and decreases product loss Novaflex Connoisseurs Beverage Hose Meets 3-A (cert# 1803), FDA & USDA standards Now selling tubing sets made from ForgeFit fittings and Novaflex Connoisseurs food & beverage tubing that is assembled in the MoreBeer! Pro production shop in Pittsburg, California. The options above are already assembled and ready to shop. Novaflex is a special kink and crush resistant suction & discharge rubber hose, designed for those demanding applications requiring a product that meets 3-A (cert# 1803), FDA & USDA standards. This tube is for non-oily applications. Designed to meet the temperatures and chemical resistance associated with "cleaning in place" systems. The ultra smooth microbe resistant tube is built on special stainless steel mandrels for cleanliness. The ForgeFit barbed connector and crimp sleeve system are designed to provide a long life and easy to clean hose connection. The long barb and the long sleeve provide a secure crimp without crushing the hose. Triple banding can slip or damage the hose during installation and has sharp edges. The ForgeFit hose barb skips the first barb to provide a gapless and smooth transition to the tubing to make it easier to keep clean. Our barb has a stop to ensure the hose does not creep closer to the clamp in service. Don't forget to add hose bumpers to your order to protect your investment! The ForgeFit® Silicone Hose Bumper is designed to protect your hose ends by absorbing the impact of the hose end hitting the floor when it's dropped. The unique built in handle makes it easier to grab and saves your back. Novaflex Construction: Tube: White Chlorobutyl Reinforcement: Multiple plies of polyester tire cord & dual monofilament helix Cover: Gray EPDM abrasion resistant Temperature Range: -40° to 240°F (CIP to 248°F) Not for continuous steam service in. mm ID 1 25.4 OD 1.64 41.65 Bend Radius 3.5 88.9
Inline mesh screen filter to pre filter liquids before passing through a pump. Will remove large particles and protect the pump mechanisms from contaminants. Features 3/4 inch barbs on the in and out sides. The clear plastic cover is removable for cleaning or replacement of the screen.
Replacement body O-ring for Euro 30 pump. This O ring is slightly smaller than the O-Ring in the head of the PMP530 & PMP535.
In Documents Tab:
Position: 6
EnoItalia Item #: G2151
Get that eye-catching cascading effect by serving your Stouts & Porters with a nitrogen tank filled with beer gas mix!
Serve still beverages on draft with pure nitrogen or argon—serving still bevs with CO2 will lead to carbonation over time
Dual high-pressure and low-pressure gauges to easily reference cylinder pressure and output pressure
CGA580 inlet compatible with standard US nitrogen and argon tanks
Made in the USA. Taprite is one of leading manufacturers of gas regulators and draft dispensing equipment
One-way shutoff valve outlet protects your regulator from backflow and can be turned on/off to stop gas flow without needing to close your tank
This Taprite Nitrogen Regulator will allow you to add Nitro-Draft capability to your home dispense system!
Use this dual gauge nitrogen regulator to connect a tank of Beer Gas mix (70% Nitorgen/30% CO2) to your keg for an authentic nitro-pour! Traditionally used for stouts and porters, a nitro pour is becoming popular with more and more beer styles, lending its signature creamy mouthfeel and head to the beer. An amazing upgrade to any brewer's draft system.
Made in the USA by Taprite. 5/16" barb.
With your own Nitrogen tank, you can add Nitro-Draft capability to your Home Dispense System!
Serve beer on Nitro! The best way to pour your favorite stouts and porters!
Made from high-quality aluminum that will never rust like steel tanks
Fill with Beer Gas Mix to get that alluring, cascading pour famously associated with Guinness
CGA580 valve pairs with standard US-style nitrogen & argon gas regulators
KOMOS® offers a full suite of first-rate draft products and draft fittings—from kegs to faucets and everything in between!
Use pure nitrogen to serve still wine, cold brew coffee, Sangria and premixed cocktails on draft
Brand new aluminum 22 cubic feet Nitrogen tank made from high strength aluminum alloy and high quality CGA580 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It can be filled with compressed (liquified) Nitrogen, Argon, or Beer Gas Mix (70% Nitro/30% CO2).
Fill with beer gas mix (70% Nitrogen/30% CO2) for dispensing beers "On Nitro". Using 100% Nitrogen is also the recommended gas for dispensing cold brew coffee, wine, or even Sangria and premixed cocktails on draft!
Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder.
Tanks should always be stored in an upright position.
Features:
Made from corrosion resistant, engineered Aluminum
Brushed finish
Thick, durable cylinder walls
DOT approved
New high quality CGA-580 valve
Light weight compared to steel tanks
Rated to 2216 PSI service / 3360 PSI test pressure PSI (allowing for Nitrogen fill)
Can also be filled with Argon or Beer Gas Mix (Nitrogen/CO2)
NOTE: You will need at Nitrogen/Argon Regulator to go with this tank, a standard CO2 regulator will not work.
A new 5 lb CO2 tank is one of the required purchases when you’re changing over from bottling to kegging your beer.
This brand new 5 lb aluminum CO2 tank ships free in the 48 contigous states. Aluminum tanks will never rust, which is why we prefer them over steel tanks. The capacity refers to the amount of compressed (liquified) CO2 the tank can hold. 5 lbs of CO2 is enough to dispense 8 to 9 5-gallon kegs of homebrew.
All new CO2 tanks are shipped empty and will require either filling or exchanging for a full tank. Most local homebrew shops will stock gas to exchange, and many local welding supply companies can fill tanks on site.
CO2 tanks should always be stored in an upright position.
Dimensions: 14.33" Tall x 5.25" wide.
Connect these pumps up to an air compressor and you get a gentle transfer solution at a very reasonable price. Flow rates are variable by regulating the inlet air pressure at the compressor and/or by applying back pressure with a ball valve.
We offer two styles of this pump, with either a polypropylene body or stainless steel body. Both models feature a Santoprene diaphragm. The Polypropylene pumps are available in 3/8", 1/2" and 1" Female Pipe Thread inlet / outlet; the Stainless Steel pumps are available in 1/2" and 1". Stainless Steel adapters to common barb sizes and to Tri-Clover style fittings are available. 1" models offer a Max Flow Rate of 53gpm and a Max Inlet Pressure of 120psi (8.3bar). Please see the specs below for information on this particular model.
Manufactured by ARO. Smaller and larger sizes are available, please call 1-800-600-0033 or e-mail support@moreflavor.com for more information.
Does not include air compressor or regulator
Specifications:
Maximum Air Inlet Pressure .............. 100 p.s.i.g. (6.9 bar)
Maximum Material Inlet Pressure ....... 10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure ................ 100 p.s.i.g. (6.9 bar)
Air Consumption @ 40 p.s.i. .............. 1 c.f.m. / gallon (approx.)
Maximum Flow Rate (flooded inlet) .... 10.6 g.p.m. (40.1 L.p.m.)
Displacement / Cycle @100 p.s.i. ......... 0.022 gal (0.083 lit)
Maximum Particle Size .................... 1/16" dia. (1.6 mm)
Maximum Temperature Limits ........... 35 to 150 F (2 to 66 C)
Noise Level @ 70 p.s.i., 60 c.p.m. ...... 72.7 db(A)
Dimensions .................................... 7 31/32" W x 9 5/16" H x 5 23/32" D
This stainless steel cart makes it easy to wheel around your pump and is small enough to fit into tight spaces. Comes with pre-drilled holes for mounting. Compatible with Euro 20 and Euro 30 flexible impeller pumps.
Flexible impeller pump for moving wine or juice Stainless steel pump head with 1.5" tri-clamp connections On/off switch for easy operation 4.4 gallons per minute flow rate Pre-wired with 110V plug Made in Italy by EnoItalia This version of the Italian-made Euro 20 features a pre-wired 110V plug. Unlike the 220V model, this pump is ready for use and does not require a plug to be wired to a bare cord. The Euro 20 is a great pump for smaller production. Featuring a SS head with 1.5” TC fittings, this flexible impeller pump is great for moving wine or juice. We have this pump set up with a forward and reverse on/off switch on the body, simplifying operation. This unit comes with mounting points for if you want to mount it to a cart or filler/filter. Features: Flow rate is 4.4 gpm Max Pressure: 46 PSI (3.2 BAR) 1.5" Tri-Clover inlet and outlet 110V single phase Pre-Wired Plug 0.5 HP motor 1.7 amps Recommended temperature range: 40 - 150°F (5 - 65°C) SS head w/ Flexible Impeller
Can be added to the PMP100 to slow down flow on command. Can reduce flow by up to 25% by taking liquid from the output and redirecting it back to the input. Also good if the pump is encounterin back pressure in your particular set up. Has 1.5" TC connection on both the in and the out.
All the programmable benefits of the EuroFill pumps Perfectly machined stainless steel lobe rotors Ideal for pushing wine through plate and frame, lenticular, and/or cartridge filters Dry stop protection Wireless remote Available with optional motorized receiving hopper The ultimate one winery pump for all applications The Lobe Rotor pump from EnoItalia is the ultimate winery pump, representing the best of all worlds. Combines all the major benefits of the EuroFill pump, via the programmable PLC, with all the benefits of a Lobe Rotor pump. Lobe Rotor pumps can also be used for filtering applications where positive pressure is necessary to pump wine through a sheet or membrane. Lobe Rotor pumps also have some of the lowest shear values which protects skins and seeds from being macerated during the pumping process. The 'smart' component is what sets this EnoItalia pump apart from other lobe rotor pumps. The built-in programmed logic controller brain allows you to know the volume pumped during any transfer. You can also program the volume you wish to transfer. The potential applications are unlimited. Program the pump to fill a barrel. Create perfect blends. Do timed pump overs. The optional receiving hopper can be used under a destemmer crusher to collect whole destemmed, or crushed grapes. Max capacity 50,700 lbs with destemmed grape, and 44,000 lbs with fermented grape. The receiving hopper is also available for purchase separately, or the pump and hopper can be purchased together. Benefits: The only pump you will need in your winery that allows you to use if for all applications. The highest quality, lowest shear value keeps skins and seeds intact to reduce unwanted tannin. The smartest plc brain for programmed volume transfers. This is the ultimate winery pump. Positive pressure allows for use in filtering applications Motorized receiving hopper included Features: Speed control Timed and programmable volume pumping Dry stop protection - pump turns off to protect pump when dry Direction reversal Pressure switch Connection for a motorized collection buffer Wireless remote control Easy to use PLC programmable controls Low profile and easily moved Max Pressure: 58 PSI (4 BAR) 3" tri-clamp inlet/outlet 3" DIN connector for hopper included 220v 60hz 3 Phase 7.5 kW Optional receiving hopper: 220v 3 Phase 0.75 kW
Replacement air tubes for variable capacity tanks. 100 cm tube fits Marchisio 1000-2000 Liter tanks.
Please note: These tubes are only compatible with Marchisio brand tanks. They will not work with Speidel or other brands of variable volume tanks.
Replacement air tubes for variable capacity tanks. 115 cm tube fits LA Inox 1850 Liter tanks.
Please note: These tubes are only compatible with Marchisio brand tanks. They will not work with Speidel or other brands of variable volume tanks.
Made to pair with the EnoItalia Lobe Rotor Pump, the optional receiving hopper can be used under a destemmer crusher to collect whole destemmed, or crushed grapes. Max capacity 50,700 lbs with destemmed grape, and 44,000 lbs with fermented grape. 220V 3 Phase 0.75 kW
