CO2 System Parts

Protect your regulator from damage in the event your tank gets knocked over. A Gauge Cage is cheap insurance that can help save you a costly regulator replacement. Mounting bolt and washer included. CO2 and Nitrogen tanks, especially the 5lb size most brewers use, are notoriously wobbly and easy to knock over once the regulator is mounted on them. This handy Gauge Cage helps protect the gauges themselves, as well as the fragile points where they thread into the regulator body, from damage in case of a fall.   Specifically sized to fit our D1060 and D1070 Taprite brand ragulators, these cages may not fit some budget regulators manufactured overseas.  

Read more less

Keep your draft system dialed in with this regulator gas board for Duotight In-Line Regulators. The gas board can hold up to six regulators, allowing you to monitor and adjust the pressure going to each keg. In the example photo, the high pressure from the gas cylinder is fed to the regulator on the left, and then stepped down from there with the lowest pressure line in the right-most position. The holes for wall mounting the board and the holes for mounting the regulators are pre-drilled for easy installation. Made from food-grade polypropylene plastic. Regulators, fittings, labels, and mounting hardware are not included. For a fully rigged gas board, we recommend the following parts: 4 x Inline Regulators 8 x Rigid 8mm Joiners 3 x Duotight 8mm Tee Pieces 1 x Duotight 8mm Elbow These items can be found below under You Might Also Need.   KegLand Part Number: KL17701  

Read more less

This shutoff valve can be used for multiple applications. Has a 1/4 in MPT thread on one side, this is commonly used in regulators, air distributors, and other keg system components. The out side has a 1/4 in MFL fitting for attaching a variety of flare fitting such as a barb ans swivel nut for gas lines. Includes a check valve, so gas can only flow in one direction, this can protect your regulator from accidential back up of beer.

Read more less

These quick disconnects feature 1/4" barbed fittings which can be used with either 3/16", 1/4" or 5/16" line. The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you need not worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade buna-n. For the female side, see our H550B.

Read more less

Great Replacement for a broken gauge.   Replacing a broken gauge on your pressure regulator is a snap with this Left Hand Thread 3000 psi Replacement Pressure Gauge for CO2 or Nitrogen regulator. Installation is simple, and it prevents you from needing to buy a whole new regulator.    Used to determine level of remaining gas in the tank.   1/4” MPT Left-hand thread.

Read more less

Great Replacement for a broken gauge.   Replacing a broken gauge on your pressure regulator is a snap with this Replacement Low Pressure Gauge for CO2 or Nitrogen regulator. Installation is simple, and it prevents you from needing to buy a whole new regulator.   1/4” MPT Right-hand thread.

Read more less

O Ring for Beer & Gas Line QD (for H550A)

Read more less

An on/off ball valve and a check valve all-in-one!   Give your regulator an extra layer of protection with this dual purpose Shut-Off Check/Ball Valve. This valve gives you the flexibility to quickly turn off CO2 and at the same time keep beer from ever traveling back up the gas line and into the regulator. Standard equipment on our regulator.   Male 1/4" NPT x 5/16" barb.

Read more less

Savvy homebrewers love quick disconnects on their gas lines! They give you the ability to quickly move hoses from one configuration to another with ease!   These quick disconnects feature 1/4" barbed fittings which can be used with 3/16", 1/4" or 5/16" line. The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you don’t need to worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade Buna-N.   In short, these QDs are durable, user friendly and versatile. A no-brainer! For the male side, see our H550A, or buy both sides together as a set.

Read more less

Add the perfect amount of restriction to any beer line to reduce foam. Eliminates the need for flow control in the faucet itself. Great for use in Jockey Boxes or anywhere you are serving beverages with varying levels of carbonation.    If you are currently using a long length of tubing to increase restriction you can now shorten your tubing. A shorter line holds less beer. Beer that is stored in the line tends to warm up quicker, adding to foaming issues, and is more likely to stale from bacteria present in the line.    Features: Adjust flow with an included Allen wrench (keeps unauthorized people from adjusting the unit) Eliminate foam from beer or slow down / speed up other beverages Fix systems with issues without having to replace lines or faucets Take the guesswork out of line restriction.  You can use shorter lines and still have perfect restriction.  You can also use larger ID lines and adjust as necessary. Easy to disassemble for cleaning, clear body for easy monitoring Made in Germany by CM Becker from Food grade plastic and stainless steel parts! Comes Equipped with 2 x 3/16" Barbs Easy to install to any existing beer line (cut line and install two clamps)

Read more less

Protect your gas regulator from liquid damage! Insert in a gas line and you will be able to shut off gas flow anytime. Has internal check flow valve that prevents liquid from traveling past, even when the ball valve is open. Not only handy, it is a regulator saver. Has 5/16" barbs for easy installation on gas lines.

Read more less

Great Replacement for a broken gauge.   Replacing a broken gauge on your pressure regulator is a snap with this Replacement Low Pressure Gauge for CO2 or Nitrogen regulator. Installation is simple, and it prevents you from needing to buy a whole new regulator.   1/4” MPT Right-hand thread.

Read more less

Gas Manifold - Pressure Relief Valve 1/4" Male Threading Set to blow off at 20 psi.

Read more less

Gas Manifold Parts - 1/4" Nipple For expanding a gas manifold.. Right Hand Thread

Read more less

Protect your regulator from damage in the event your tank gets knocked over. A Gauge Cage is cheap insurance that can help save you a costly regulator replacement. Made from 304 stainless steel. Mounting hardware included. This gauge cage is made specifically for the KOMOS Dual Gauge Regulator (D1077) and will fit like a glove. Protect your regulator at an affordable price and avoid having to purchase a new one if bumped into or knocked over.    Please Note: Regulator not included. Shown for demo only.  

Read more less

Keep your draft system dialed in with this regulator gas board for Duotight In-Line Regulators. The gas board can hold up to six regulators, allowing you to monitor and adjust the pressure going to each keg. In the example photo, the high pressure from the gas cylinder is fed to the regulator on the left, and then stepped down from there with the lowest pressure line in the right-most position. The holes for wall mounting the board and the holes for mounting the regulators are pre-drilled for easy installation. Made from food-grade polypropylene plastic. Regulators, fittings, labels, and mounting hardware are not included. For a fully rigged gas board, we recommend the following parts: 6 x Inline Regulators 12 x Rigid 8mm Joiners 5 x Duotight 8mm Tee Pieces 1 x Duotight 8mm Elbow These items can be found below under You Might Also Need.   KegLand Part Number: KL17718  

Read more less

Great Replacement for a broken gauge.   Replacing a broken gauge on your pressure regulator is a snap with this Right Hand Thread 3000 psi Replacement Pressure Gauge for CO2 or Nitrogen regulator. Installation is simple, and it prevents you from needing to buy a whole new regulator.    Used to determine level of remaining gas in the tank.   1/4” MPT Right-hand thread fits most regulators.

Read more less

Savvy homebrewers love quick disconnects on their gas lines! They give you the ability to quickly move hoses from one configuration to another with ease!   These quick disconnects feature 3/8" barbed fittings which can be used with 5/16", 3/8" or 7/16" line. The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you don’t need to worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade Buna-N.   In short, these QDs are durable, user friendly and versatile. A no-brainer!   This is a direct replacement to the Female Quick Disconnect with 3/8" Barbs that is featured on the BrewBuilt CoolStix™.

Read more less

Replace a broken knob on your CO2 tank, or keep one on hand as a spare. Fits on Kegland CO2 tanks. This is the knob only. Does not included CO2 tank or any related hardware. KegLand Part Number: KL30625

Read more less

Works with our H550 series Quick Disconnects.  This is a male Quick Disconnect with 1/4" MPT on the other side. 

Read more less

1/4" Back Mounted Thread, 0-15 lb Dial Range.  Please Note: Color/ style of gauge may vary

Read more less

This 1.5 in TriClamp pressure and vacuum relief valve is a great way to protect your tank. It will relieve pressure over 1.5 BAR but will also let in air if the tank is a vacuum inside to prevent the tank from imploding. Features: Relief pressure: 1.5 BAR (22 psi) Allows pressure in during a vacuum 1.5 in TC Kegland Part Number: KL01823

Read more less

If your Taprite Regulator is drifting or losing pressure, why not try repairing it rather than replacing? Over time the internal diaphragm can wear out resulting in drifting pressure or a slow leak through the regulator body Refurb your unit with this Regulator Rebuild Kit and return your Taprite regulator to it’s lost glory.    Works with Taprite CO2 or N2 regulators. Not intended for other regulators. Taprite Part Number: 7740-19-SP

Read more less

Plastic quick disconnect with 3/8" barb which can be used with either 1/4", 5/16" or 3/8" line. The quick disconnect functionality is activated by a shrouded thumb latch on the female QD. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you need not worry about them leaking gas. The o-ring is food grade buna-n. This is a non-valved QD. It does not have an internal shut-off like H550A. For the female side, see our H550B.

Read more less

Use this quick disconnect set to seal a soda bottle under CO2 pressure. An ideal way to bring homebrew to a party without all the accessories. TIP N' TRICK: Add a CO2 tee inline with your current CO2 setup and install the H481 Kent Shut-Off Female QD w/ 1/4 in Barb included. This way you always have access to CO2 accessible to put your beer under pressure before leaving for the party. * A single-handed connection and disconnection * Strong plastic that can handle 250 degrees, very durable, and is medical-grade compliant and made from FDA approved material * Easy installation into your home brewery * KENT Systems quarter turn design functions safely

Read more less

This replacement spring is intended for use with our adjustable stainless steeel pressure relief valve - D1832L & D1833L. These units are adjustable from 0 to 30 psi. Example photo shown. The spring you receive may not match the photo exactly.  

Read more less

Use this cap to seal a soda bottle under CO2 pressure. An ideal way to bring homebrew to a party without all the accessories. TIP N' TRICK: Add a CO2 tee inline with your current CO2 setup and install our H481 Kent Shut-Off Female QD w/ 1/4 in Barb. This way you always have access to CO2 accessible to put your beer under pressure before leaving for the party. * A single-handed connection and disconnection * Strong plastic that can handle 250 degrees, very durable, and is medical-grade compliant and made from FDA approved material * Easy installation into your home brewery * KENT Systems quarter turn design functions safely regardless of pressure up to 125 p.s.i.

Read more less

An adjustable pressure relieve valve with a range from 0 to 30 psi. Made from stainless steel this is non-threaded and designed to be welded in place.     For a 1/4" MPT option see D1833L.

Read more less

Use this quick disconnect to seal a soda bottle under CO2 pressure using our H470-Kent Shut-Off Male QD - Soda Bottle Cap. An ideal way to bring homebrew to a party without all the accessories. TIP N' TRICK: Add a CO2 tee inline with your current CO2 setup and install this H481 Kent Shut-Off Female QD w/ 1/4 in Barb. This way you always have access to CO2 accessible to put your beer under pressure before leaving for the party. * A single-handed connection and disconnection * Strong plastic that can handle 250 degrees, very durable, and is medical-grade compliant and made from FDA approved material * Easy installation into your home brewery * KENT Systems quarter turn design functions safely regardless of pressure up to 125 p.s.i.

Read more less

The CMBecker Inline Flow Control 4mm Barb is necessary for those looking to use tubing that has an inner diameter of 3/16" Use with CMBecker In-Line Flow Control Compensator Stainless steel nipple, only stainless steel touches your beverage Works with CMBecker International shanks. Includes CMBecker beer nut The size is 4mm. When using with 3/16" hose you may need to slightly heat hose (using hot water) to stretch hose over barb (this is how we do it!) Just make sure you clamp it properly to get a good seal This will not work with a standard shank, it works with CMBecker shanks. These seal at two places and do not have a flat end (see photo)

Read more less

The CMBecker Inline Flow Control 7mm Barb is necessary for those looking to use tubing that has an inner diameter of 5/16 or 3/8" Use with CMBecker In-Line Flow Control Compensator Stainless steel nipple, only stainless steel touches your beverage Works with CMBecker International shanks. Includes CMBecker beer nut The size is 7mm which is slightly wider than 1/4" at 0.27" This will not work with a standard shank, it works with CMBecker shanks.

Read more less

The CMBecker International Inline Flow Control 10mm Barb is necessary for those looking to use tubing that has an inner diameter of 3/8". It is slightly smaller than 1/2", but it will fit a 1/2" ID Hose if properly clamped. Use with CMBecker In-Line Flow Control Compensator Stainless steel nipple, only stainless steel touches your beverage Works with CMBecker International shanks. Includes CMBecker beer nut The size is 10mm which is between 1/2" and 3/8". When using with 3/8" hose you may need to slightly heat hose (using hot water) to stretch hose over barb (this is how we do it!) When using with 1/2" it will be loose, but we have used it with syphon hose and thicker high heat (EJ beverage or silicone) hose. Just make sure you clamp it properly to get a good seal. This will not work with a standard shank, it works with CMBecker shanks

Read more less

Stainless pressure relief valve. Rated to 1 BAR / 15 psi. Non-threaded. For welding in place only.

Read more less