The DigiBoil is a versatile electric kettle that can be used as a standalone unit or integrated into your current brew system to serve a variety of functions. Easily brew 5-gallon extract batches. Use it to preheat your strike water or sparge water to a precise temperature. Pair it with a pump and heat exchanger to use it for HERMS brewing. Or slap on a still top lid and condenser for distilling! With so many ways to use the DigiBoil, and an affordable price tag to boot, it's hard not to get excited about this electric kettle! The Gen 2 DigiBoil features an upgraded glass lid, allowing you to monitor your heated or boiling liquid. Interested in using the DigiBoil for all-grain brewing? With the Mash Upgrade Kit, you can easily convert the DigiBoil into an electric mash tun! This DigiBoil model has two built-in heating elements that run off a 110V plug. One element is 1000w and the other is 500w for a combined 1500 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage both elements to quickly go from steeping temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s).  Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach 1/2" FPT fittings if desired. Features: 304 stainless steel construction 9 gallon total capacity Digital temperature control 110V / 15A power and plug (5 ft. cord) Dual heating element control (1000w and 500w) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Glass lid Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Compatible with reflux and pot still (DS130 & DS120)* External Dimensions: 29" H x 15" W (including handles) Internal Dimensions: 19.5" H x 11.75" W ETL Listed *Distilling: to use the DigiBoil with a distilling condenser, you will need to purchase the still top lid and gasket (DS124). Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States.  It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA). KegLand Part Number: KL07245

Read more less

The BrewBuilt SlingBlade is an innovative electric heating element designed to promote a rolling boil and even heat distribution. Shaped for Performance and Convenience The SlingBlade's unique crescent-shaped design positions all of the heating power on one side of the kettle, sending thermal energy upward to the surface that then cascades downward on the opposite side of the kettle. This movement creates a dynamic turbulence that evenly distributes heat while creating a vigorous, rolling boil. Other heating elements stick right out into the middle of the kettle or use a full circle design that rings the kettle wall. This can cause an obstruction for immersion chillers or make it difficult to stir without banging into the element. The SlingBlade was designed to avoid these issues. By remaining on one side of the kettle, the element will be out of the way of your immersion chiller, and since the element follows the curvature of the kettle wall, it won't interfere with the flow of wort during whirlpool. Ultra-Low Watt Density An electric element transfers power to your wort by applying heat, but if this heat is too concentrated you will get local heating that is hotter than 212°F. This catalyzes Maillard Reactions, which can lead to darker beer than intended and produce unwanted caramelization. Think of these reactions like roasting a marshmallow. First it gets a light brown, we call this Maillard reactions, a little hotter and it gets a dark brown, we call this caramelization, then it turns black and we call this pyrolysis (burnt or scorched). While all kettles undergo these reactions, an electric element can concentrate more heat into a small area, which can quickly scorch your wort. Our experience is that at 90-watts per square inch recipes need to be modified to account for the element and light beers never come out quite right. The SlingBlade element was designed at 50-watts per square inch to reduce the chance of scorching while still providing a vigorous boil. For even lower watt density, consider the Boil Vigor Controller. Tri-Clamp Connection The SlingBlade installs quickly and easily on any kettle with a T.C. ferrule thanks to the curved, non-circular design. This also makes it a breeze to remove the element for cleaning between uses. The SlingBlade heating elements were designed to fit perfectly with BrewBuilt brewing kettles, but you may find them suitable for other kettles as well. They should be used with T.C. ferrules no longer than 1" in length. For dimensions and recommended minimum kettle diameter, please see the chart below. Features: Made from Incoloy alloy with proprietary coating for long life 1.5" Tri-Clamp connection Unique offset design promotes rolling boil Ultra-Low Watt Density eliminates scorching UL Certified components Specs: 240 Volt L6-30 plug 20 Amp breaker required for 10 & 15 gal element 30 Amp breaker required for 22 & 31 gal element 50-gallon kettle requires 2 x BE538 and 2 x 30 amp circuits SKU Kettle Vol. Wattage Length Radius Min. Kettle Ø BE535 10 gal 3750 13.25" 6.3" 13.75" BE536 15 gal 4500 16.75" 7.3" 15.75" BE537 22 gal 5000 17.25" 8.3" 17.75" BE538 31 gal 5750 19.5" 9.3" 19.75" Please note: Length is measured from the tip of the heating element to the T.C. connection. Radius is measured from the middle of the T.C. connection to the outermost edge of the element's curve. ***In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.*** Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.

Read more less

A powerful, 304 stainless steel heating element well suited for most kettles. With its weldless design and a diameter of 1.25", it's easy to install. Simply drill a 1.25" hole in your kettle and tightening the nut from the outside. The heating element requires a power cord which can be purchased separately. Electrical connection requires a computer power connection IEC320 C13 to your 110 or 220 v plug). Available in either 1600 watt 110 volt or 2200 watt 220 volt. Features: Food grade, high temperature silicone seal The element itself is 11.5" long, 0.75" diameter Designed for use with 5 gallon batches Please Note - Having electrical devices around liquid can be hazardous, and should not be left unattended. Please use caution while using this device, and read the instruction manual prior to use. Use the 1.25" Hole Saw to drill a hole for this product.   Kegland Part number: KL03513

Read more less

Ready to upgrade your DigiBoil into a DigiMash? With the DigiMash upgrade kit you can convert the DigiBoil into a full blown electric all-in-one system. Includes false bottom, malt pipe with bottom screen, wire support, and malt pipe handle. Simply place the false bottom inside the kettle and install the malt pipe, fill with water and heat to your desired strike temperature, then add your grain and set your desired mash temperture on the digital controller. Once your mash is complete, lift up the malt pipe, drain the wort and sparge, then remove the malt pipe and proceed to boil. Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen Installation & Use: Place the false bottom inside the kettle Install the wire support in the channel located at the top of the kettle Place the mesh screen inside the malt pipe and attach the handle Lower the malt pipe into the kettle so it rests on the wire support Fill with strike water and heat to desired strike temperature When desired temperature is reached, add grain and stir until well mixed When your mash is complete, use the handle to lift out malt pipe and rotate 90° so the malt pipe feet sit on the wire support Allow the wort to drain into the kettle and sparge the grain with warm water (165-175°F) When you're done collecting your wort, remove the malt pipe and proceed to boil   Please note: only the 500-watt element should be used to increase mash temperatures when the Malt Pipe is in place. Using the higher watt element(s) with the Malt Pipe inserted may cause scorching of the grain.   Kegland Part Number: KL13055

Read more less

Anvil Foundry Recirculation Pump Kit for 6.5 / 10.5 gal units.   Features: Anvil Recirculation Pump 4 ft. of Silicone Hose 4 Hose Clamps Flow Clamp Stainless Return Tube Perforated Disc Eye Bolt & Nuts for Eye Bolt

Read more less

Ripple-style electric brewing heating element with 1.5" tri-clamp connection. With 5,500 watts of power, this unit will easily heat 20+ gallons of wort. Measures 4" wide and 14.5" from TC connection to tip of element. Specs: 5,500 watts 240 Volt L6-30 plug 30 Amp breaker required In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.    

Read more less

Ready to upgrade your DigiBoil into a DigiMash? With the DigiMash upgrade kit you can convert the DigiBoil into a full blown electric all-in-one system. Includes false bottom, malt pipe with bottom screen, wire support, and malt pipe handle. Simply place the false bottom inside the kettle and install the malt pipe, fill with water and heat to your desired strike temperature, then add your grain and set your desired mash temperature on the digital controller. Once your mash is complete, lift up the malt pipe, drain the wort and sparge, then remove the malt pipe and proceed to boil. The Gen 2 DigiMash Upgrade Kit is backwards compatible with Gen 1 DigiBoils. Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen Installation & Use: Place the false bottom inside the kettle Install the wire support in the channel located at the top of the kettle Place the mesh screen inside the malt pipe and attach the handle Lower the malt pipe into the kettle so it rests on the wire support Fill with strike water and heat to desired strike temperature When desired temperature is reached, add grain and stir until well mixed When your mash is complete, use the handle to lift out malt pipe and rotate 90° so the malt pipe feet sit on the wire support Allow the wort to drain into the kettle and sparge the grain with warm water (165-175°F) When you're done collecting your wort, remove the malt pipe and proceed to boil Please note: only the 500-watt element should be used to increase mash temperatures when the Malt Pipe is in place. Using the higher watt element(s) with the Malt Pipe inserted may cause scorching of the grain. Kegland Part Number: KL12980

Read more less

The easiest way to power the BrewBuilt™ SlingBlade! This professionally wired watertight switch gives you a simple On/Off control of your heating element. Switches both legs of a 220V 30AMP circuit and comes with 5 ft. input and output cords with molded LP6-30P ends. It also features two handy tabs for mounting to a wall. Don't wear out your expensive plugs and sockets hot patching your 220V burner elements. Plugging your element directly into a live power outlet will cause a small spark, and when done repeatedly this can damage the plug and the socket, especially with high voltage 220V appliances. Not only is the power switch more convenient to turn your element on and off during the brew day, it will eliminate the risk of damage done by hot patching.  

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.   304 stainless steel splash resistant construction Industrial design using commericial quality components for long life and easy serviceability Digital power reading for precise repeatability. No more guessing if you found the sweet spot on the dial Outlet fully disconnected when powered off for added safety, unlike some one-leg designs Linear power control for better repeatability at low power settings Wall mount bracket allows you to get the controller off the table and out of the way Dial your brew day up to 11 with the BrewBuilt™ Boil Vigor Controller! This controller allows you to control the current of a 208-240V heating element up to 30 amps. Perfect for dialing in your boil vigor for more consistent boil-off rates or adjusting the heat input to a still wash pot. The controller works by adjusting the percentage of power delivered to the heating element. The power is increased in a linear fashion from 0 to 100% as you adjust the dial from 1 to 11. Features industrial-style power switch, dial knob, and digital amm meter mounted on a splash resistant stainless steel enclosure. Pre-cut mounting holes allow you to hang the controller on your brew stand on the wall at eye-level. We highly recommend mounting the controller so you don't have to worry about keeping an area of your table dry where you might lay it down. L6-30 connections with 4 ft. cords on either end. Compatible with all 208-240V elements 30 amps and lower. While L6-30 are the most common elements available, yours may need an adapter. The Boil Vigor Controller uses a generously overrated SSR with a very large fan-cooled heatsink for better reliability. An SSR's life expectancy is directly related to its operating temperature, and this unit is built with the lowest Q heat dissipation system offered at the homebrewing level. It includes a contactor to fully shut off both legs when you throw the power switch, making the free end of the cord safer when the element is not plugged in. The display gives you a reading of the actual current being consumed by your element in Amps. On some systems, a small change in the adjustment makes a large current change at the element, especially at lower settings used during hop stands and distillation. The BrewBuilt controller provides a linear control and a digital readout to eliminate the guessing, allowing you to focus on your process and not your equipment. If you'd prefer not to mount the controller to your wall, consider the stainless steel Controller Stand.   **Caution: In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.**  

Read more less

Perfect for powering 230V / 30 amp electric elements, power controllers and brewing systems away from your main wall socket. Comes with male and female L6-30 sockets on either end. 10 feet long.

Read more less

304 stainless steel splash resistant construction Industrial design using commercial quality components for long life and easy serviceability On/Off thermostat control Outlet fully disconnected when powered off for added safety, unlike some one-leg designs Wall mount bracket allows you to get the controller off the table and out of the way Keep your temps tight with the BrewBuilt™ HLT Controller! Perfect for keeping your sparge water or mash water at your set temperature—it allows you to control a 208-240V heating element up to 30 amps based on temperature. The controller works by turning the burner power on and off at 100% power until it reaches the temperature setpoint. Features industrial-style power switches, and a 1/6 DIN Controller mounted on a splash resistant stainless steel enclosure. Pre-cut mounting holes allow you to hang the controller on your brew stand on the wall at eye-level. We highly recommend mounting the controller so you don't have to worry about keeping an area of your table dry where you might lay it down. L6-30 connections with 4 ft. cords on either end. Compatible with all 208-240V elements 30 amps and lower. While L6-30 are the most common elements available, yours may need an adapter. Uses a 9' stainless braided PT-100 temperature sensor. The HLT Controller includes a contactor to fully shut off both legs when you throw the power switch, making the free end of the cord safer when the element is not plugged in. If you'd prefer not to mount the controller to your wall, consider the stainless steel Controller Stand.   **Caution: In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.**    

Read more less

The DigiBoil is a versatile electric kettle that can be used as a standalone unit or integrated into your current brew system to serve a variety of functions. Easily brew 5-gallon extract batches. Use it to preheat your strike water or sparge water to a precise temperature. Pair it with a pump and heat exchanger to use it for HERMS brewing. Or slap on a still top lid and condenser for distilling! With so many ways to use the DigiBoil, and an affordable price tag to boot, it's hard not to get excited about this electric kettle! The Gen 2 DigiBoil features an upgraded glass lid, allowing you to monitor your heated or boiling liquid. Interested in using the DigiBoil for all-grain brewing? With the Mash Upgrade Kit, you can easily convert the DigiBoil into an electric mash tun! This DigiBoil model has two built-in heating elements that run off a 220V plug. One element is 1900w and the other is 500w for a combined 2400 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage both elements to quickly go from steeping temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s). If you have access to 220V power, this is definitely the unit we recommend. Although 110V power is enough to get up to boil, 220V will get you there faster and provide a much more vigorous boil. Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach 1/2" FPT fittings if desired. Features: 304 stainless steel construction 9 gallon total capacity Digital temperature control 220V / 15A power NEMA 6-30 plug (5 ft. cord) Dual heating element control (1900w and 500w) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Glass lid Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Compatible with reflux and pot still (DS130 & DS120)* External Dimensions: 29" H x 15" W (including handles) Internal Dimensions: 19.5" H x 11.75" W ETL Listed *Distilling: to use the DigiBoil with a distilling condenser, you will need to purchase the Distillation Lid. Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States.  It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA). KegLand Part Number: KL07252

Read more less

Preheat your mash before beginning the brewing process with this 1000W Electric Bucket Heater. This handy little tool works in conjunction with a product like the Ranco or Johnson temperature controller by enabling you to set an exact hot liquid temperature on the controller, and then attaching it to the bucket heater. The temperature controller will turn off the bucket heater once it reaches your desired temperature. Our bucket water heater is designed to use with water in a bucket or cooler where an open flame cannot be used, and you can even use it to heat a bucket of water for cleaning with a powdered brewery wash. This water bucket heater measures 17 inches from the handle to the tip and comes with a 6-foot long cord. It requires at least 6 inches of water for full submersion, and it can only be used with a maximum depth of 14 inches.  Unit has stainless steal heating element and guard.  Does not include clip for mounting.  Please Note - Having electrical devices around liquid can be hazardous, and should not be left unattended. Please use caution while using this device, and read the instruction manual prior to use.

Read more less

Used on a commercial brewing system to shut off electricty or gas before the kettle runs dry.  This horizontal float switch conveniently fits into a 1.5" tri-clamp port. It is designed to control the run-dry circuit in an electric brewing system. The contacts are intended to control a relay, contactor, or SSR and should not be used to interrupt full power to an electric element/burner. 50W. The unit is not fit to use on a circuit load, but suitable for signal output.  

Read more less

Digital temperature control Triple heating element control (2000w, 1000w and 500w) 17 gallon total capacity 304 stainless steel construction 220V / 20A power This is a versatile electric kettle that can be used as a standalone unit or integrated into your current brew system to serve a variety of functions. Easily brew 10-gallon extract batches. Use it to preheat your strike water or sparge water to a precise temperature. Pair it with a pump and heat exchanger to use it for HERMS brewing. Or slap on a still top lid and condenser for distilling! With so many ways to use the DigiBoil, and an affordable price tag to boot, it's hard not to get excited about this electric kettle! The Gen 2 DigiBoil features an upgraded glass lid, allowing you to monitor your heated or boiling liquid. Interested in using the DigiBoil for all-grain brewing? With the Mash Upgrade Kit, you can easily convert the DigiBoil into an electric mash tun! This DigiBoil model has three built-in heating elements that run off a 220V plug. The elements are 2000w, 1000w and 500w for a combined 3500 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage all three elements to quickly go from steeping temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s).  Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach 1/2" FPT fittings if desired. More! Features: NEMA 6-30R plug (4.5 ft. cord) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Glass lid Temperature reads in °F or °C With elements turned off, hold both the +/- buttons to switch between °F or °C Compatible with reflux and pot still (DS130 & DS120)* External Dimensions: 29" H x 19.5" W (including handles) Internal Dimensions: 20.25" H x 15.75" W ETL Listed *Distilling: to use the DigiBoil with a distilling condenser, you will need to purchase the still top lid (DS127). Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States.  It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. MoreBeer! is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA).   Kegland Part number: KL07313 NOTE: Due to the size of this item, it is not eligible for international shipping.    

Read more less

This 21" whirlpool works perfectly with the 10.5 Gallon Foundry™, brew kettles, and any other brewing system. The rotating rubber piece allows it to secure to the side of any vessel, no matter the thickness. The Swirly™ uses a 1/2" Straight Pipe Thread for hose connections and includes a hose barb for connecting your water supply. Patent pending.   The 21" Swirly fits any vessel that is 15"-27" in container height.

Read more less

Designed to be used as a whirlpool solution in TC Brew Kettles (including the eKettle).  1/2" NPT to 1.5" TC 3 Piece Ball Valve 1/2" ID Valve Body Integrated Whirlpool Nozzle Compatible with Ss TC Brew Kettle and eKettles 304 Stainless Steel Does not include TC Clamp or Gasket Not intended for use with Ss Brew Kettle Brew Master Edition.

Read more less

This 15" whirlpool works perfectly with the 6.5 Gallon Foundry™, brew kettles, and any other brewing system. The rotating rubber piece allows it to secure to the side of any vessel, no matter the thickness. The Swirly™ uses a 1/2" Straight Pipe Thread for hose connections and includes a hose barb for connecting your water supply. Patent pending.   The 15" Swirly fits any vessel that is 11"-21" in container height.

Read more less

Replacement mat for eKettle Contoured to match the eKettle's footprint Black silicone construction Durable and easy to clean Prevents heat damage to brewing surfaces Prevents scratches from forming on the underside of the eKettle Reduces risk of burns when brewing on heat-conductive surfaces Included with eKettle purchase

Read more less

Anvil Foundry Recirculation Pump Kit for 18 gal units.   Features: Anvil Recirculation Pump 4 ft. of Silicone Hose 4 Hose Clamps Flow Clamp Stainless Return Tube Perforated Disc Eye Bolt & Nuts for Eye Bolt

Read more less

PLEASE NOTE: The supplier of this product has temporarily halted shipments to addresses within the state of California. If you are a CA resident, please note your order will not be fulfilled and will ultimately be canceled. We hope to have this issue resolved with the supplier as soon as possible. Versatile Functionality: The Create+ Boiler is compatible with two different distillation columns. Pair it with the Create+ T500 Column & Condenser to produce high ABV neutral spirits like vodka, or use it with the Create+ Alembic Copper Dome & Condenser for flavorful spirits such as whiskey and gin. Precise Power Control: With two power switches, you can choose between 1600W and 1100W. This allows for a more gentle and controlled boil, which is ideal for crafting more delicate spirits while preserving their unique flavors and aromas. Expandable Design: An included 2" Tri-Clamp to DN40 Threaded Adapter allows you to connect a wide variety of 2" tri-clamp accessories, providing the flexibility to experiment with different setups and attachments. The Create+ Boiler 25 L is the recommended boiler base for use with the Create+ T500 Column & Condenser and the Create+ Alembic Copper Dome & Condenser. With a maximum capacity of 25 liters, the Create+ Boiler is designed for distillers seeking precise control and versatile functionality. When paired with the Create+ T500, it can produce high-quality and high ABV neutral alcohol (vodka) or distilled water. When paired with the Create+ Alembic Copper Dome & Condenser it can create flavorsome spirits (gin, whiskey, rum and bourbon) and aromatic hydrosols, retaining delicate flavors and aroma from your wash or botanicals. The Create+ Boiler 25 L includes a 2" Tri-Clamp to DN40 Threaded Adapter allowing for connection to 2" tri-clamp accessories, so you can experiment with different setups and attachments. It features two power switches. When both switches are on, the element will be supplied full power (1600W for 120V units). You can lower this to 1100W by switching off the 500W switch (120V unit). This is ideal for maintaining a gentler boil during distillation, especially for dark spirits like whiskey, rum, and bourbon. For safety during operation the boiler features an automatic reset switch. The stainless-steel ball valve tap provides durability and ease of use when discarding your contents after distillation. Elevate your distillation experience with the Create+ Boiler 25 L, designed for flexibility, precision, and superior results across a range of applications. Whether you’re crafting spirits, distilling water, or producing hydrosols, the T500 Boiler offers the control and performance you need. DISCLAIMER: Please note that in certain countries alcohol distillation and the possession of distilling equipment is illegal and permits/licenses may be required. For guidance or advice, contact your relevant local authorities. Key Features Dual element control switches provide more control during distillation - when both switches are in the ON position, the element will be supplied full power of 2200W (1600 if using a US/CA unit). When one switch is in the OFF position, it will only consume 1100W (or 1100W/500W if using a US/CA unit) of power. Designed in New Zealand Boil dry reset Thermal cut out fuse Waste discharge tap with a stainless-steel ball valve Boiler lid with 48 mm opening 25 L Boiler capacity Connects to 2" tri-clamp distilling accessories 304 grade stainless steel construction High temperature resistant food grade silicone Specifications Capacity: 25 L (6.6 Gallons) Dimensions: H 64 cm x W 36 cm x D 37 cm H 25.1" x W 14.1" x D 14.5" Weight: 5.42 kg (11.9 lbs) Power: 2200W (1600W for US/CA Units) NOTE: The Boiler is designed primarily for small to medium-sized distilling setups that do not have heavy, off-center attachments. When used with the Still Spirits Boiler 25 L lid or Alembic Dome, it is reasonably flexible and is sturdy enough to fit components within the following specifications: A total column & condenser height up to 1.1 m (3.6 ft) from the boiler lid or dome. A total column & condenser weight up to 11 kg (24 lbs), including up to 2 kg lbs) off-center weight from a swan neck, lyne arm, or condenser running in parallel with the column and offset up to 160 mm (6") to the main column. Included in Box Create+ Boiler 25 L Create+ Boiler Lid 2" Tri-clamp to DN40 Threaded Adapter (includes: Silicon gasket and DN40 Nut)  

Read more less

Designed to extend an eController further alway from an eKettle. Very useful in three vessel setups. Two lengths available. L6-30 Power Plug  10 Gauge SJOOW Power Cable Temp Prob Harness

Read more less

Due to the integrated PT100 thermo probe, our RIMS units are only compatible with Ss Brewtech eControllers Our Recirculating InfuSsion Mash System (RIMS) features a 3500w Incoloy 800 helical element with a thermoprobe integrated into the base which is designed to read wort temperature as it leaves the RIMS housing.  When used with an InfuSsion Mash Tun, the system is designed to provide the brewer the temperature gradient between mash and recirculating wort, allowing the perfect pump speed to be dialed in.   The RIMs kit includes a fully welded housing with TC connections, silicone base, and neoprene insulating jacket.  For stabilization and control in a multi-step mash process there is simply not a better system on the market.   Connectivity was an important consideration for our eBrewing Systems, we wanted the flexibility and familiarity of a plug that could be adapted to an existing customer setup, and the reliability of a UL approved connector type.  For the 240VAC element connector, we settled on the common NEMA L6-30 standard, which is a 3-wire twist-lock plug type, capable of delivering 30 amps of current.  Finally, for the PT100 temperature probes we opted for the 3.5 mm mini jack connector standard, commonly used for headphones, which is both durable and easy to use. 3500w Incoloy 800 Helical Element w/ integrated thermoprobe Sanitary TC Connections Neoprene Insulation Jacket NEMA L6-30 Plug 240VAC

Read more less

TWO - 240VAC 30AMP GFCI Dedicated Circuits Required Designing every piece of our electric brewing equipment from scratch has enabled us to introduce a new level of process control, flexibility, and performance.  Every detail has been carefully thought through and refined. Every component of our new eControllers were designed in house or selected to enhance the ebrewing experience.  Beginning with the custom extruded 6061 aircraft-grade aluminum housing, which is CNC machined, and then coated in a durable black anodized finish. Using this approach allowed us to keep the system compact, portable, and functional.  The housing includes an integrated carry handle for easy setup and take down, a tee-slot for alternative mounting options, along with a heatsink to keep the internal electrical components cool. The boilkettle output on the eController is driven by a fully proportional PID controller, which doesn't rely on high speed switching to modulate heat.  Instead, voltage is modulated through an internal SSVR, this means element wattage is proportional.  A switch located just above the PID allows the user to operate the controller in manual or automatic modes. In manual mode, the proportional output can be fine-tuned on a scale of 0-100% of total element output which is ideal for dialing in a perfect rolling boil.  Alternatively, in automatic mode, the PID algorithm manages the proportional output relative to process temperature, to hold a steady HLT or mash temp for instance.  The eController quickly finds equilibrium with environmental heat loss characteristics, and can maintain a high degree of accuracy during each brewing process. The heater button allows the user to cycle the element on or off without shutting down the power to the entire unit, or adjusting the PID output setting, which is especially helpful during the occasional boil-over. This feature also allows the controller to be used to monitor a process temperature, such as during runoff or latter stages of the sparge process without the risk of dry firing the element.  Lastly, the controller features two accessory outputs, which would commonly be used for pumps, but could also be used for a mill, lighting, or even a phone charger. Connectivity was an important consideration for our eControllers, we wanted the flexibility and familiarity of a plug that could be adapted to an existing customer supplied kettle or element, and the reliability of a UL approved connector type.  For 240VAC main power and element connectors, we settled on the common NEMA L6-30 standard, which is a 3-wire twist-lock plug type, capable of delivering 30 amps of current.   For the accessory connections, we settled on using a NEMA 5-15 standard, which is just a standard residential 120 VAC outlet.   Finally, for the PT100 temperature probes we opted for the 3.5 mm mini jack connector standard, commonly used for headphones, which is both durable and easy to use. Extruded Anodized 6061 Aluminum Housing Omron Proportional PID Controller Automatic and Manual Modes On/Off Element control PT100 temperature probe (2) 120 VAC Accessory receptacles TWO - 240VAC L6-30 Plugs (2) discreet 30A GFCI circuits required TWO - 240VAC 30AMP GFCI Dedicated Circuit Required Designed to be used with Ss Brewtech eKettles and RIMS. Use with other heating elements, especially (but not limited to) those of different wattages, can cause damage to the eController not covered under the warranty policy.

Read more less

Designing every piece of our electric brewing equipment from scratch has enabled us to introduce a new level of process control, flexibility, and performance.  Every detail has been carefully thought through and refined. Every component of our new eControllers were designed in house or selected to enhance the ebrewing experience.  Beginning with the custom extruded 6061 aircraft-grade aluminum housing, which is CNC machined, and then coated in a durable black anodized finish. Using this approach allowed us to keep the system compact, portable, and functional.  The housing includes an integrated carry handle for easy setup and take down, a tee-slot for alternative mounting options, along with a heatsink to keep the internal electrical components cool. The eController is driven by a fully proportional PID controller, which doesn't rely on high speed switching to modulate heat.  Instead, voltage is modulated through an internal SSVR, this means element wattage is proportional.  A switch located just above the PID allows the user to operate the controller in manual or automatic modes. In manual mode, the proportional output can be fine-tuned on a scale of 0-100% of total element output which is ideal for dialing in a perfect rolling boil.  Alternatively, in automatic mode, the PID algorithm manages the proportional output relative to process temperature, to hold a steady HLT or mash temp for instance.  The eController quickly finds equilibrium with environmental heat loss characteristics, and can maintain a high degree of accuracy during each brewing process. The heater button allows the user to cycle the element on or off without shutting down the power to the entire unit, or adjusting the PID output setting, which is especially helpful during the occasional boil-over. This feature also allows the controller to be used to monitor a process temperature, such as during runoff or latter stages of the sparge process without the risk of dry firing the element.  Lastly, the controller features two accessory outputs, which would commonly be used for pumps, but could also be used for a mill, lighting, or even a phone charger. Connectivity was an important consideration for our eControllers, we wanted the flexibility and familiarity of a plug that could be adapted to an existing customer supplied kettle or element, and the reliability of a UL approved connector type.  For 240VAC main power and element connectors, we settled on the common NEMA L6-30 standard, which is a 3-wire twist-lock plug type, capable of delivering 30 amps of current.   For the accessory connections, we settled on using a NEMA 5-15 standard, which is just a standard residential 120 VAC outlet.   Finally, for the PT100 temperature probes we opted for the 3.5 mm mini jack connector standard, commonly used for headphones, which is both durable and easy to use. Extruded Anodized 6061 Aluminum Housing Omron Proportional PID Controller Automatic and Manual Modes On/Off Element control PT100 temperature probe 240VAC L6-30 Plugs 30A GFCI circuit required (2) 120 VAC Accessory receptacles 240VAC 30AMP GFCI Dedicated Circuit Required Designed to be used with Ss Brewtech eKettles and RIMS. Use with other heating elements, especially (but not limited to) those of different wattages, can cause damage to the eController not covered under the warranty policy.

Read more less

Designing every piece of our electric brewing equipment from scratch has enabled us to introduce a new level of process control, flexibility, and performance.  Every detail has been carefully thought through and refined. Every component of our new eControllers were designed in house or selected to enhance the ebrewing experience.  Beginning with the custom extruded 6061 aircraft-grade aluminum housing, which is CNC machined, and then coated in a durable black anodized finish. Using this approach allowed us to keep the system compact, portable, and functional.  The housing includes an integrated carry handle for easy setup and take down, a tee-slot for alternative mounting options, along with a heatsink to keep the internal electrical components cool. The boil kettle output on the eController is driven by a fully proportional PID controller, which doesn't rely on high speed switching to modulate heat.  Instead, voltage is modulated through an internal SSVR, this means element wattage is proportional.  A switch located just above the PID allows the user to operate the controller in manual or automatic modes. In manual mode, the proportional output can be fine-tuned on a scale of 0-100% of total element output which is ideal for dialing in a perfect rolling boil.  Alternatively, in automatic mode, the PID algorithm manages the proportional output relative to process temperature, to hold a steady HLT or mash temp for instance.  The eController quickly finds equilibrium with environmental heat loss characteristics, and can maintain a high degree of accuracy during each brewing process. The heater button allows the user to cycle the element on or off without shutting down the power to the entire unit, or adjusting the PID output setting, which is especially helpful during the occasional boil-over. This feature also allows the controller to be used to monitor a process temperature, such as during runoff or latter stages of the sparge process without the risk of dry firing the element.  Lastly, the controller features two accessory outputs, which would commonly be used for pumps, but could also be used for a mill, lighting, or even a phone charger. Connectivity was an important consideration for our eControllers, we wanted the flexibility and familiarity of a plug that could be adapted to an existing customer supplied kettle or element, and the reliability of a UL approved connector type.  For 240VAC main power and element connectors, we settled on the common NEMA L6-30 standard, which is a 3-wire twist-lock plug type, capable of delivering 30 amps of current.   For the accessory connections, we settled on using a NEMA 5-15 standard, which is just a standard residential 120 VAC outlet.   Finally, for the PT100 temperature probes we opted for the 3.5 mm mini jack connector standard, commonly used for headphones, which is both durable and easy to use. Extruded Anodized 6061 Aluminum Housing Omron Proportional PID Controller Automatic and Manual Modes On/Off Element control PT100 temperature probe 240VAC L6-30 Plugs 30A GFCI circuit required (2) 120 VAC Accessory receptacles 240VAC 30AMP GFCI Dedicated Circuit Required Designed to be used with Ss Brewtech eKettles and RIMS. Use with other heating elements, especially (but not limited to) those of different wattages, can cause damage to the eController not covered under the warranty policy.

Read more less

The Essential Kits are designed to get you up and brewing with one click.  It's highly recommended you add this to your cart with your purchase of a RIMS. Sight Glass | 2.25" Hose Barb | 1/2" to 1.5" TC (2) Clamp | 1.5" TC clamp (3) Gasket | 1.5" TC gasket (3) Tubing | ½” ID Silicone (5ft) Hose Clamps (2)

Read more less