Stainless steel ball valves are almost a necessity in homebrewing. These are most commonly used on your kettle, allowing you to control the flow of your liquids during transfers. Using stainless steel ball valves is recommended, as these will come in direct contact with your wort, and using anything other than stainless could leave a metalic taste in your beer. Stainless steel ball valves are also easier to keep clean, and will last longer.
304 Stainless steel, full port, two piece ball valves that will last for years. Easy to clean with 1/2" FPT on input and output.. High grade 304-stainless made to last with1000psi rating. We've been selling these same valves from the same manufacturer for over 10 years. This is non-locking valve meaning that it does not come with the locking clip. Many users prefer this because you are not constantly lifting the clip to open and close the valve. If you would prefer a ball valve with a locking clip please see the Brewbuilt Ball Valve.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and the two PTFE gaskets that form the seal when closed.
This ball valve with male and Female Beer Thread (5/8" BSP) is incredibly handy for those wanting to shut off flow of liquid and gas lines on keg couplers or shanks. Highly recommended if you are disconnecting your coupler and not re-attaching to another keg immediately. Made from 304 stainless steel.
Kegland Part number: KL00406
This BrewBuilt Stainless Steel Ball Valve features a locking mechanism that keeps the valve from being opened by a child or passing dog while you are brewing. Easy to clean 2 piece design, constructed from high grade 304-stainless made to last. 1/2" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and the two PTFE gaskets that form the seal when closed.
Features:
1/2" FPT on inlet and outlet
Locking Mechanism on Handle
304 SS construction with PTFE gaskets
Two-Piece Construction for easy cleaning
Full Port design for minimal pressure loss / resistance
BrewBuilt: Designed for Brewing, Built to Last.
Stainless steel 3-piece ball valve with tri-clamp connections. A great option for T.C. kettles, pumps, and conicals to go from 1.5" tri-clamp to any 1.5" tri-clamp connection or accessory. Full port for higher flow rate.
This stainless steel ball valve is the perfect match to most homebrewing kettles with a 1/2" coupler or nipple on the bottom. The 3-piece design makes it easy to take apart and keep clean, preventing any spoilage organism from lingering between batches. It has a 1/2" FPT inlet and outlet.
Stainless steel 3-piece ball valve with tri-clamp connection and 1/2" female NPT out. A great option for T.C. kettles, pumps, and conicals to go from 1.5" tri-clamp to any 1/2" male threaded connection or accessory. Full port for higher flow rate. A seat in the back of the valve allows for the installation of a pick up tube or racking arm.
Need a ball valve with a TC connection? Ss Brewtech has got you covered! This 1/2 in ball valve has 1.5 in TC on one side, and 1/2 in female NPT on the other. It is perfect for Ss Brewtech BME kettles as a tangential inlet.
Features:
3 piece body
Made from 304 stainless steel
1/2 in ID valve body
1.5 in TC
1/2 in. female NPT
This stainless ball valve has a PCO 1881 female thread on one side for attaching to the male thread on the FermZilla lid or collection container and a 3/4" BSP Female thread on the other side for attaching other fittings.
The 20mm bore (approx.) makes it possible to perform low oxygen dry hopping through the ball valve.
Stainless steel 3 way ball valve with 1/2" female BSP at all ends. The T Port configuration has multiple open and closed positions. Please refer to see the function of each handle position.
KegLand Part Number: KL15882
Stainless - 1/4 in 3 Way Ball Valve - FPT x MPT x FPT
Please Note: Valves include a Teflon gasket. Do not soak the valves in PBW which can corrode Teflon material after prolonged contact.
This is a 304 Grade Stainless Steel Ball Valve 1/2 BSP Female x 1/2 BSP External Welded Thread. Often used to convert a keg into boil kettle, also known as a keggle.
Includes:
1 x 1/2" Ball Valve with 1/2" BSP male & female thread
1 x Recessed 1/2" Nut
1 x Silicone Washer (used on the inside of vessel)
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 1/4" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed. Here at MoreFlavor! we think this ball valve is actually easier to clean than 3-piece ball valves (such as our H602D).
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 3/4" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed.
304 grade stainless steel ball valve. Full port for maximum flow rate. 1,000 psi rating for water, oil, or gas.
1/2" BSP female threads at inlet and outlet.
KegLand Part Number: KL03681
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 3/8" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed.
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 1" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed.
Please Note: the ball valve may be difficult to turn at first, but it will become less resistant after it is rotated back and forth a couple times.
