Fermenters & Accessories

Airlocks are another one of those necessary pieces of equipment for every homebrewer.  If you ferment in a carboy or bucket this 3 piece airlock is a must! It’s a popular alternative to the triple ripple type of airlock because it can be taken apart and cleaned, and is easy to fill. (However we do sell the triple ripple type (FE371) in case you are used to that type and would like to stay with it.)    While a simple device not all airlocks are the same. Some other designs have only a couple holes in the plastic lid and this can cause the airlock to pop out during an active fermentation.  Our design features multiple holes that allow CO2 to escape easily.  Additionally some other airlocks have a cross hatch design on the bottom. We have found this more easily leads to Krausen clogs and the airlock being pushed out of the fermenter. Ours is open, allowing Krausen foam to enter the airlock if necesary.  Better to clean your airlock out than to find it laying on the floor next to your fermenter 3 days later.     Another cool feature of this 3-piece airlock is that 1/2" ID Silicone tubing will fit onto the center post for use as a blowoff. In the cases where you are using a yeast known to produce lots of Krausen (wlp002 from White Labs or 1968 from Wyeast for example) remove the top cover, remove the plastic 'hat', and install the silicone tubing.  Run the silicone tubing into a jar or bucket of water. When fermentation dies back down remove the tubing and replace the hat and cover.   Please Note: Airlock only - stopper not included.

Read more less

Universal stoppers have a longer taper to help produce a better fit and a snug seal, and a lip which prevents them from falling into your container. Available with a 3/8 inch hole for an airlock, or solid with no hole. #10 size is recommended for PET carboys.

Read more less

S-shaped airlocks are the "OG" airlocks for home beer and winemaking. They make it easy to spot fermentation activity, and have no loose peices to lose. The advantage of this type of airlock is that they have a smaller chamber so you can more closely observe the CO2 rising and therefore the rate of fermentation. They are also handy when you are cooling a beer as there is less chance of sucking airlock water back into the fermentation. They cannot be cleaned manually if they get dirty during the ferment. That is why many homebrewers prefer 3-piece airlocks for the active portion of the ferment, when the krausen (foam) from fermentation might be pushed up into the airlock. Please Note: Stopper Not Included. 

Read more less

Perfect for use as a 5-gallon batch beer fermenter or bottling bucket Inlcuded plastic spigot for easy gravity transfers or attaching a bottle filling wand Sediment blocker on the spigot's back locking nut helps minimize trub pickup when racking out after fermentation Once you've upgraded to a carboy or other fermenter, the bucket will remain a reliable brewing tool for cleaning and sanitizing purposes External volume markers provide a convenient reference point when filling the bucket with water to make cleaner or sanitizer solution A six gallon food grade bucket for fermentation or bottling with a built in spigot and external volume markings up to five gallons.  Outlet barb accepts 3/8" ID vinyl tubing.  To use as a fermenter you will need to pick up the optional lid, stopper, and an airlock.  Includes our new Sediment Block Spigot, which will help minimize trub uptake as you rack after fermentation.  If using this as a bottling bucket, simply rotate the spigot to maximize product output.  Spigot includes gasket and sediment blocking lock nut and can easily be removed for cleaning and sanitizing. If you use the bucket for fermentation be sure to use care when cleaning. Do not use any abrasive pads that would scratch. Once you get a scratch in a plastic bucket it is very hard to sanitize.  This is also why we don't recommend storing equipment in a bucket between uses as a fermenter. A hot PBW soak is often a perfect way to clean a bucket, followed by a Star San soak for killing bacteria. Bucket has external volume markings up to 5 gallons. 17.5" H x 12" Ø Please Note: Buckets are translucent and do not come with lids Buckets are not designed to hold pressure Lids are not gasketed and so do not always form a perfect, airtight seal. Not intended for long-term storage Food-Grade to 180° 

Read more less

Smooth, ribless design prevents yeast and bacteria buildup, making sanitation a breeze Punted bottom and conical top promote sediment collection and reduce oxidation during storage Extra-wide 4" mouth opening simplifies filling, additions, and cleaning Constructed from heavy-duty, virgin PET plastic without plasticizers Made with food-grade and BPA-free materials The Ported Fermonster is a brand new fermenter designed specifically for fermentation. MoreBeer! gave product feedback for over 2 years of development and we think they nailed the design. The large lid allows for easy filling and makes hop or oak additions a breeze. The smooth sides are fantastic for sanitization - no ribs or texture to collect yeast or bacteria.  The large 7 gallon size was designed to provide ample space for fermentation and you'll find the molded in volume markers super handy for accurate filling. The punted bottom allows sediment to collect to the sides so that you can siphon liquid from the center.  Because they are made from virgin PET plastic they nearly unbreakable and a lot safer than similar glass carboys. Also notice the conical top which reduces surface area if you plan to store beer or wine long term.   These ported versions come with our plastic spigot (FE347), allowing for easy racking and sampling! Made from heavy PET plastic, the same material used in 2 L soda bottles, which is nearly impermeable to oxygen penetration.  Due to the thickness of the material and the overall geometry the Fermonster does not require ribs or dimples for stability.  That results in a super smooth interior surface that reduces yeast and sediment buildup making it the easiest to clean, most sanitary PET carboy on the market.  The huge 4" opening makes filling a breeze, and cleanup is as easy as wiping down the inside.  The 7 gallon volume is a monster of a fermenter, reducing blowoff issues seen with standard 5 and 6 gallon carboys. Fermonsters are easily moved by hand or consider using our Carboy Carrier for even greater ease of use. These fermentors are completely air-tight and the lids sealed tight with an O-Ring.  Additional O-Rings and Lids both with and without holes are available for purchase, see our You Might Also Need items below. Features: 4" wide mouth carboy - easy to clean! Ported version includes Spigot for easy racking Food grade PET plastic construction is nearly impermeable to oxygen penetration No hard to clean dimples or ribs Volume Markers at 5, 6, and 7 Gallons Punted bottom O-Ring and Lid with one hole is included (Fits #10 Stopper) Additional O-Rings and Lids available Weight: 1.5 lbs Temperature Limit: 140° F Height: 20.9 inches Diameter: 11.3 inches Completely taste and odor free Perfect for Beer, Wine, Cider, Mead, Kombucha or any other fermented beverage! Thick walls for better oxygen barrier.

Read more less

Got a stuck lid on your Fermonster? Get it open much easier with this specially designed lid opener. It easily slides onto the lid and gives you comfortable hand grips to open a stuck lid. Note: We do not recommend using this tool to tighten the lid because the seal is made by the o-ring and not the pressure between the lid and neck.

Read more less

The most affordable 5-gallon batch beer fermenter you'll find! Food-grade plastic buckets make a perfect starter fermenter for beginner brewers—simply add a lid with stopper and airlock Once you've upgraded to a carboy or other fermenter, the bucket will remain a reliable brewing tool for cleaning and sanitizing purposes External volume markers provide a convenient reference point when filling the bucket with water to make cleaner or sanitizer solution A food-grade six gallon plastic bucket perfect for all kinds of home beer or winemaking activities. Plastic buckets are often used as a fermenter, bottling bucket, or even sanitizer bucket. We go through thousands which helps keep our price down. If you want to use it as a fermenter you will also need to pick up the optional lid, stopper, and airlock. This bucket is also available in a version that includes a spigot (see recommended products below). If you use this plastic bucket for fermentation be sure to use care when cleaning. Do not use any abrasive pads that would scratch. Once you get a scratch in a plastic bucket it is very hard to sanitize.  This is also why we don't recommend storing equipment in a bucket between uses as a fermenter. A hot PBW soak is often a perfect way to clean a bucket, followed by a Star San soak for killing bacteria. Bucket has external volume markings up to 5 gallons. 17.5" H x 12" Ø Please Note: Buckets are translucent and do not come with lids Buckets are not designed to hold pressure Lids are not gasketed and so do not always form a perfect, airtight seal. Not intended for long-term storage Food grade up 180°F

Read more less

With the FermZilla Pressure Kit you can ferment under pressure, carbonate, and serve without ever needing to move your beer out of the fermenter. The kit inlcudes two stainless female threaded ball lock fittings with barbs, which thread onto the existing openings atop the FermZilla's lid. For the beverage out, you'll have a silicone dip tube with stainless steel float, allowing you to always draw from the clearest beer at the top of the tank. Pick up the Pressure Kit and turn your FermZilla into a true unitank! The silicone dip tube is 31" long. It will work perfectly as is for the 55L FermZilla. For the 27L model we recommend cutting the dip tube shorter to remove unwanted slack. With the optional Floating Dip Tube Filter, you can prevent hop material and other solids from ever entering the dip tube. Especially handy when you're pulling samples mid-fermentation! Fermenting Under Pressure: The pressure kit allows for fermenting under pressure, which will reduce esters and fusel alcohol production. This means you can ferment at warmer temperatures than you normally would, even making lagers at room temperature. Most commerical beer is fermented under pressure simply due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the distinct differences between homebrewing and brewing on a commercial scale. The FermZilla's lid already comes with a built-in pressure relief valve that will blow at 35 psi; the pressure kit simply allows you to add CO2 through the ball lock fitting. We strongly recommend that you also purchase an adjustable pressure relief valve, or spunding valve, which allows you to set a lower pressure. It's always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure.   Carbonating, Transferring, and Serving: When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using a spunding valve. This means you can eliminate kegging and serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Attach a beer line from the FermZilla's bev out to your keg and enjoy the easiest kegging experience ever.  You can also choose to send carbonated beer through a beer filter on the way to your keg.  When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator.     Eliminate Oxidation: Since the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock.   Key Features: Ferment beer under pressure to reduce ester and fusel alcohol production Always draw clear beer with the floating dip tube Keg beer that has already been carbonated Use CO2 to push beer into a keg or through a filter into a keg Eliminate kegging altogether by carbonating and serving directly from the FermZilla Installation Note: For best performance, ensure there is not an excess amount of slack when the silicone dip tube is installed and shorten it if needed. With the floating dip tube installed on your empty FermZilla, you ideally want the dip tube to hang freely with just enough length for the end of the dup tube to touch the bottom of the tank. Please note: pressure kit does not include the lid pictured in the example photo. The ball locks and floating dip tube are installed on the FermZilla's existing lid.

Read more less

#7 stopper - with 3/8 inch hole. Top diameter 1.43 inches (36.3 mm), bottom diameter 1.19 inches (30 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).

Read more less

Replacement O-ring for the Fermonster Plastic Carboy lids (all sizes use same lid).   The o-ring is a little tricky to install so please be sure to watch our video in the video tab on how to install it.   

Read more less

You will love the versatility of this stopper!   The Universal Stopper with Hole fits a 2.8, 3, 5, 6, or 6.5 gallon glass carboy. Also fits our 500ml Erlenmeyer flask, and can be flipped over and used in most bottles! Made with a longer taper from a different material from standard stoppers to minimize popping out when wet.   Please Note: This stopper will not fit in plastic carboys, Better Bottles or Speidel Plastic Fermenters.

Read more less

The Temp Twister Cooling Coil is the ideal option for maintaining fermentation temperatures in any model FermZilla. Use an IceMaster Glycol Chiller or ice bath with submersible pump to push coolant through the coil when temps get too hot. Designed for the FermZilla but can can be used with virtually any fermenter that has an opening diameter of 4-3/8" or wider. The inlet and outlet are extra long so the coil can be used with every sized FermZilla. In order to cut them to an appropriate length for your application, we recommend this compact pipe cutter. To install, simply drill two 22 mm (approx. 7/8") holes into the lid of the fermenter and use the included Duotight bulkhead fittings to attach the coil to the lid. The FermZilla will still be pressurizable after installing the Temp Twister, just be careful to drill the holes no wider than needed to fit the Duotight bulkheads. If you're using the Temp Twister with EVABarrier tubing, we suggest adding 2 x DUO112 to your order to help route your inlet and outlet lines. Specifications: Coil Diameter - 4.33" Coil Height - 14" Overall Length - 26.75" Tubing Diameter - 3/8" OD Made from 304 Stainless Steel Includes 2 x 9.5 mm Duotight bulkheads Kegland Part number: KL14618  

Read more less

The lowest price Pressuizable fermentor out there Prefect for most ales that ferment in 2 weeks or less Super smooth PET makes cleaning very easy Transfer to your keg closed and under pressure, oxygen free PET is a better oxygen barrier than fermentors made of HDPE Super lightweight yet strong and shatterproof The FermZilla All Rounder is the most affordable pressurizable fermenter on the market. Although it doesn't feature a dump valve like the FermZilla Conical, the All Rounder carries the same pressure rating, making it an absolute steal if you're looking to ferment under pressure, perform pressure transfers, or want to carbonate and serve directly from the fermenter. The All Rounder is made from super smooth PET that's easy to clean, and the simple design means no nooks or crannies for microbes to hide. With a 4.75" lid opening, you'll have no trouble getting your arm inside to scrub away stubborn krausen rings. As with all FermZilla fermenters, the lid features molded drill locations that make installing accessories like a thermowell or Temp Twister Cooling Coil a breeze. In order to unlock the full potential of the All Rounder, you'll want to pick up the 55L FermZilla Pressure Kit. The silicone dip tube will be a little long, but you can cut it shorter to the appropriate length. The pressure kit is available with either stainless or plastic ball lock caps. Why MoreBeer! loves the All Rounder FermZilla: Super smooth PET makes cleaning very easy. Pressure rated lid and PET material make for a better oxygen barrier than fermenters made of HDPE. Lightweight and easy to move around, yet strong enough to be considered shatterproof. The 4.75" lid opening makes it easy to get your arm inside and clean after use. The lid is designed for the easy installation of accessories such as a thermowell or cooling coil. Price! A pressurizable fermenter in this price range is an incredible value, and it opens the door for many cold-side processes that can't be done in a normal carboy or plastic fermenter. What's Included: FermZilla 30L All Rounder Fermenter Stainless Steel Stand Stainless Steel Handle Top Lid with PRV (35 psi) 3-Piece Airlock Adhesive Thermometer Graduation Sticker Specs: 30 L (7.9 gal) Total Volume Pressure Rated to 2.5 Bar (36.2 psi) Height in Stand - 21.7" Height w/ Airlock - 24.2" Tank Diameter - 13.9"  Lid & Collection Container Ports - 28 mm PCO 1881 threads Temperature Rating: When not under pressure, do not expose to liquids above 131°F When under pressure, do not expose to any temperatures above 95°F* *Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years. Kegland Part number: KL15189   NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.

Read more less

Solid replacement lid for the all sizes of Fermonster fermenter.  Does not include a gasket. Perfect for transporting wort after big brews where it was needed to drive the wort home before fermentation.    

Read more less

Due to high demand, the case of 100 is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.   Use this foam stopper with your Erelenmeyer flask when making a yeast starter. Aeration is an important aspect of making a strong, healthy starter. This is why we recommend using a stir plate, which provides continuous aeration. This foam stopper will allow air to flow freely into your flask while keeping pesky bugs and other contaminants out. A quick spray down with sanitizer is all you need. Suitable for flasks or other vessels with an inner diameter opening of 35-45mm (1-3/8" - 1-3/4"). Reusable Resists alcohols, bases, esters, and dilute acids Autoclavable up to 249°F (121°C).

Read more less

For use with stopper and airlock on 6 gallon bucket. Comes with 1 1/4" hole which fits a #7 or universal stopper. Please Note: Lids are not gasketed and so do not always form a perfect, airtight seal. Not intended for long-term storage.

Read more less

Use the Fermonster Carboy Carrier to move your Fermonster, Plastic or Glass Carboy around with ease. The harness and strap handles are made from heavy-duty polypropylene, enabling you to haul up to 100 lbs of your wort or finished beer without the risk of losing your grip. Cradle your carboy with confidence and avoid spilling! The carrier comes with handles in two different positions for added convenience. Short handles for lifting and long handles for moving. The long handles are especially handy when lifting your carboy out of a top-loading fermentation locker. Compatibility: 3, 5 and 6 gallon Plastic Carboys 3, 5 and 6 gallon Glass Carboys 3, 6 and 7 gallon Fermonsters Take Care of the Carrier: Avoid prolonged exposure to sunlight Machine wash safe (low temperatures only) Do not clean with bleach or products that contain bleach Hang dry in the shade Do not iron  

Read more less

This Spigot can be easily installed onto any bucket for added convenience.   Drill a 1" hole and install in bucket with the gasket against the exterior of the bucket.    Spigot uses 3/8 in ID tubing.

Read more less

This stainless steel hop tube is ideal for keeping kettle additions from clogging your pump or heat exchanger, and works perfectly for dry hopping in a keg or wide-mouth fermenter. Holds approximately 5 oz of pellet hops, allowing some space to permit full extraction of the hop oils. The stainless chain makes it the perfect partner to our Corny Keg Lid with Welded Tab. Hang the tube inside your keg for post fermentation hop, fruit, wood chip, or spice additions. When it's time to remove the hops/adjuncts simply pull the tube out. Works great for timing exactly how long your beer sits on the hops, oak, or other flavoring addition. 2.6" diameter 11.8" tall Made from 304 stainless steel Kegland Part Number: KL05210

Read more less

Wide mouth carboys are the easiest glass fermenter to clean with plenty of room to get your arm inside to scrub Add bagged flavoring additions and remove them freely when finished—this can be nearly impossible with traditional narrow neck glass carboys Watch fermentation activity as it's happening! The ultimate advantage of translucent glass or plastic fermenters Ported lid with removable cap sized for a #5 stopper & airlock Carrying harness included for easier handling Glass carboys have been a staple of the brewing and winemaking world for generations, but traditional tight neck carboys aren't without their limitations. Standard glass carboys can be difficult to clean after fermentation. The wide mouth carboy is extremely easy to clean—simply removing the lid allows you to get your hand or arm all the way inside to scrub away stubborn sediment.  Each carboy comes with a carrying harness. Features: Gasketed lid for tight seal Included carrying harness Ported lid ready for #5 stopper & airlock 165mm (6.5") lid opening Continuous thread, 5mm pitch Please note: The carrying harness should not be used to move the vessel when full. The airlock lid is primarily recommended for short fermentations.

Read more less

Grab everything you need to ferment under pressure with the FermZilla All Rounder and we'll toss in the BlowTie Spunding Valve for FREE! This kit includes the 30L FermZilla All Rounder, ball lock cap adapters for the lid and collection container, floating dip tube with filter attachment, and the BlowTie 2 ball lock spunding valve. Everything you need to ferment under pressure, carbonate in vessel, and pressure transfer. The FermZilla All Rounder is the most affordable pressurizable fermenter on the market. Although it doesn't feature a dump valve like the FermZilla Conical, the All Rounder carries the same pressure rating, making it an absolute steal if you're looking to ferment under pressure, perform pressure transfers, or want to carbonate and serve directly from the fermenter. The All Rounder is made from super smooth PET that's easy to clean, and the simple design means no nooks or crannies for microbes to hide. With a 4.75" lid opening, you'll have no trouble getting your arm inside to scrub away stubborn krausen rings. As with all FermZilla fermenters, the lid features molded drill locations that make installing accessories like a thermowell or Temp Twister Cooling Coil a breeze. Why MoreBeer! loves the All Rounder FermZilla: Super smooth PET makes cleaning very easy. Pressure rated lid and PET material make for a better oxygen barrier than fermenters made of HDPE. Lightweight and easy to move around, yet strong enough to be considered shatterproof. The 4.75" lid opening makes it easy to get your arm inside and clean after use. The lid is designed for the easy installation of accessories such as a thermowell or cooling coil. Price! A pressurizable fermenter in this price range is an incredible value, and it opens the door for many cold-side processes that can't be done in a normal carboy or plastic fermenter. What's Included: FermZilla 30L All Rounder Fermenter Stainless Steel Stand Stainless Steel Handle Top Lid with PRV (35 psi) 3-Piece Airlock Adhesive Thermometer (1) Red Ball Lock Carbonation Cap (1) Yellow Ball Lock Carbonation Cap Use one color for gas and one for liquid! Stainless Steel Float with Silicone Dip Tube Weighted Mesh Filter Attachment (KEG6571) All Rounder Stand Harness FREE BlowTie Spunding Valve FermZilla All Rounder Specs: 30 L (7.9 gal) Total Volume Pressure Rated to 2.5 Bar (36.2 psi) Height in Stand - 21.7" Height w/ Airlock - 24.2" Tank Diameter - 13.9"  Lid & Collection Container Ports - 28 mm PCO 1881 threads Temperature Rating: When not under pressure, do not expose to liquids above 131°F When under pressure, do not expose to any temperatures above 95°F* *Please note that the temperature rating for the PET tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer liquid into the tank below 131°F or to use hot liquids below this temp to clean the tank. When under pressure, you should make sure to keep your unit in an environment no hotter than 95°F and to keep your fermentation temperature below this temp as well. If you are using kveik yeast to ferment under pressure, we highly recommend using temperature control. Installation Note: For best performance with your Floating Dip Tube, ensure there is not an excess amount of slack when the silicone dip tube is installed and shorten it if needed. With the floating dip tube installed on your empty FermZilla, you ideally want the dip tube to hang freely with just enough length for the end of the dup tube to touch the bottom of the tank. NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.

Read more less

#10 stopper - with 3/8 inch hole. Top diameter 2 inches (51 mm), bottom diameter 1.66 inches (43 mm), length 1.10 inch (28 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).  

Read more less

Heavy-duty HDPE plastic fermentation and stoarge tank Made from food-safe materials with extra thick walls to preserve the aroma of your beverage Rotating plastic spigot eliminates the need to use an auto-siphon or racking arm to transfer liquid Wide top port opening for easy cleaning Airlock & stopper included Made in Germany by Speidel The future is here today, and the future is HDPE Fermentation & Storage Tanks from Speidel. Made in Germany from nothing but undyed and food-safe plastic, these tanks are produced with particularly thick walls which preserves the aroma and the alcohol for a markedly long time. The stable carrying handles have been tried and tested for decades and are extremely durable. Are you tired of carboys? Hate siphoning to transfer? Wish you could ferment larger batches in a single container? Sick of lifting 50lbs by a small metal handle? Done with worrying about shattered glass, injury and lost product? Well then have we got the solution for you! These heavy duty plastic tanks offer a fantastic fermentation & storage solution at a great price. Key Features: Heavy duty HDPE construction is durable and resists oxygen transfer. None of the risks of working with glass. Small footprint makes them easy to store - take better advantage of the space you have to dedicate to wine & beer making. Built-in handles make these tanks easy to move, even when full. Large lid opening makes them easy to clean by hand - say goodbye to your carboy brush! All ports seal with gaskets and the vessel can be fully sealed for long-term storage. Includes a spigot and oversized 2-piece Speidel airlock. Designed and manufactured in Germany by Speidel, the makers of our legendary commercial wine tanks Suggested Applications: 12L: Perfect for storing small lots, making experimental batches and taking some of your beer or wine along with you to your next party. 20L: Ideal for secondary fermentation and storage of 5 gallon batches. 30L: The vessel for fermenting wine kits and 5 gallon batches of beer with plenty of headspace and no need for a blowoff tube. 60L: Perfect for fermenting larger batches of wine or 10 gallon batches of beer in a single container! Only 4" larger in diameter than a 6.5 gallon carboy! 120L: Ferment & Store large batches of anything - your creativity is the only limit! Approximate Dimensions: 13.5in Diameter x 18.5in Height (w/out airlock in place). Note - The maximum temperature that these plastic fermenters can handle is 140F. FAQ: Can filled containers be carried by the handles? Depending on the weight—barrels up to 30L are no problem—60L is the limit and should not be carried when completely full. The handles have a weight capacity of 30kg (66 lbs). Is there an upper limit on the alcohol content of the stored liquid? In principle, there is not. However, it should be noted that the higher the alcohol content, the faster the seals and, to a lesser extent, the tank itself will wear out. Up to what temperature can the containers be used? For short periods of time the containers can withstand temperatures of up to 80°C (176°F). This temperature should not be exceeded. For longer periods of time the containers can be used at temperatures up to 60°C (140°F).

Read more less

Extra-large food-grade plastic bucket fermenter perfect for wine kits or high krausen beers like Hefeweizen Almost a full 2 gallons larger than standard 6-gallon buckets giving you plenty more room for active fermentations and larger batches of wine or beer Comes complete with lid, airlock grommet, 3-piece airlock, and plastic spigot with rotating tap (see note below) If you do not require a spigot or other accessories, the 7.9-gallon bucket can also be purchased by itself This is a 7.9 gallon plastic fermenter complete with lid, airlock, and spigot. The rotating spigot allows you to push the bucket deeper into your counter or benchtop without obstruction. When it's time to transfer out, bring the bucket to the edge of your counter and rotate the spigot to point down. These buckets are made from Polypropylene and are ideal for all types of fermentations, especially beers with high krausen. Why Polypropylene? These buckets are made from polypropylene as it is less porous and significantly smoother than other HDPE fermenters. HDPE is porous and can harbor microbial activity making it more difficult to clean and sanitize. Being less porous, polypropylene also does not absorb aroma like HDPE so there is less flavor carry over from batch to batch. Kit Includes: 7.9 gallon plastic bucket Plastic lid with hole and grommet Airlock Spigot Please note: the spigot hole comes pre-molded into the bucket and needs to be drilled out before installing the spigot. We recommend using a 5/8" drill bit and taking care not to strip the female threads that accept the spigot. The spigot includes a back nut that won't be needed—simply remove the back nut and thread in the spigot with the gasket in between the neck of the spigot and the bucket. The lid forms a very tight seal and requires a decent amount of downward force to lock in place.

Read more less

Smooth, ribless design prevents yeast and bacteria buildup, making sanitation a breeze Punted bottom and conical top promote sediment collection and reduce oxidation during storage Extra-wide 4" mouth opening simplifies filling, additions, and cleaning Constructed from heavy-duty, virgin PET plastic without plasticizers Made with food-grade and BPA-free materials The Fermonster is a brand new fermenter designed specifically for fermentation. MoreBeer! gave product feedback for over 2 years of development and we think they nailed the design. The large lid allows for easy filling and makes hop or oak additions a breeze. The smooth sides are fantastic for sanitization - no ribs or texture to collect yeast or bacteria. The punted bottom allows sediment to collect to the sides so that you can siphon liquid from the center.  Because they are made from virgin PET plastic, they're nearly unbreakable and a lot safer than similar glass carboys. Also notice the conical top which reduces surface area if you plan to store beer or wine long term. These ported versions come with our plastic spigot (FE347), allowing for easy racking and sampling! Made from heavy PET plastic, the same material used in 2 L soda bottles, which is nearly impermeable to oxygen penetration.  Due to the thickness of the material and the overall geometry, the Fermonster does not require ribs or dimples for stability.  That results in a super smooth interior surface that reduces yeast and sediment buildup making it the easiest to clean, most sanitary PET carboy on the market.  The huge 4" opening makes filling a breeze, and cleanup is as easy as wiping down the inside. These fermentors are completely air-tight and the lids sealed tight with an O-Ring.  Additional O-Rings and Lids both with and without holes are available for purchase, see our You Might Also Need items below.   Features: 4" inner diameter wide mouth carboy - easy to clean! Food grade PET plastic construction is nearly impermeable to oxygen penetration No hard to clean dimples or ribs Punted bottom O-Ring and Lid with one hole is included (Fits #10 Stopper) Additional O-Rings and Lids available Weight: 1.5 lbs Temperature Limit: 140° F Height: 14.6 inches Diameter: 9 inches Completely taste and odor free Perfect for Beer, Wine, Cider, Mead, Kombucha or any other fermented beverage! Thick walls for better oxygen barrier. Please note: the pictured #10 Stopper (FE470VS) and three piece airlock (FE370) are not included.

Read more less

Rubber grommet that is perfect for making a sealed container into a fermenter. Fits our 3 piece or S-shaped airlocks.  fits a 1/2" hole. Kegland Part number: KL01625

Read more less

Size 15/16" - 1 1/16" To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole.

Read more less

The MonsterMesh is perfect for adding dry hops to your beer! Keep your dry hopping on a precise schedule by adding them to this mesh sleeve inside the Fermonster Plastic Carboy, then easily pull them out after the desired contact time. This mesh sleeve is custom made for the FerMonster Plastic Carboy. The plastic ring sits inside the neck of the fermenter, and the lid can be secured on top to make an airtight seal. The ring actually holds onto the neck of the FerMonster so there's no risk of the mesh sleeve falling into the carboy. Made from food grade materials, the #50 mesh will not affect the flavor of the beer or wine, and is temperature rated to 122°F. Designed for multiple uses, the MonsterMesh can be cleaned in the dishwasher and sanitized with the sanitizer of your choice. The MonsterMesh can be used alongside the MiniMesh to hold multiple additions. The MonsterMesh will sit on the neck of the carboy, and the MiniMesh can be inserted through the stopper hole in the lid. This way you can have two different infusions starting or stopping at different times.  

Read more less

Smooth, ribless design prevents yeast and bacteria buildup, making sanitation a breeze Punted bottom and conical top promote sediment collection and reduce oxidation during storage Extra-wide 4" mouth opening simplifies filling, additions, and cleaning Constructed from heavy-duty, virgin PET plastic without plasticizers Made with food-grade and BPA-free materials The Ported Fermonster is a brand new fermenter designed specifically for fermentation. MoreBeer! gave product feedback for over 2 years of development and we think they nailed the design. The large lid allows for easy filling and makes hop or oak additions a breeze. The smooth sides are fantastic for sanitization - no ribs or texture to collect yeast or bacteria.  The 6 gallon size is great for most fermentations, and the larger 7 gallon is available for even bigger beers. The punted bottom allows sediment to collect to the sides so that you can siphon liquid from the center.  Because they are made from virgin PET plastic they nearly unbreakable and a lot safer than similar glass carboys. Also notice the conical top which reduces surface area if you plan to store beer or wine long term.   These ported versions come with our plastic spigot (FE347), allowing for easy racking and sampling! Made from heavy PET plastic, the same material used in 2 L soda bottles, which is nearly impermeable to oxygen penetration.  Due to the thickness of the material and the overall geometry the Fermonster does not require ribs or dimples for stability.  That results in a super smooth interior surface that reduces yeast and sediment buildup making it the easiest to clean, most sanitary PET carboy on the market.  The huge 4" opening makes filling a breeze, and cleanup is as easy as wiping down the inside.  Fermonsters are easily moved by hand or consider using our Carboy Carrier for even greater ease of use. These fermentors are completely air-tight and the lids sealed tight with an O-Ring.  Additional O-Rings and Lids both with and without holes are available for purchase, see our You Might Also Need items below. Features: 4" wide mouth carboy - easy to clean! Ported version inlcudes spigot for easy racking Food grade PET plastic construction is nearly impermeable to oxygen penetration No hard to clean dimples or ribs Volume Markers at 5 and 6 Gallons Punted bottom for less sediment transfer during racking O-Ring and Lid with one hole is included (Fits #10 Stopper) Additional O-Rings and Lids available Weight: 1.5 lbs Temperature Limit: 140° F Height: 19.25 inches Diameter: 11.25 inches Completely taste and odor free Perfect for Beer, Wine, Cider, Mead, Kombucha or any other fermented beverage! Thick walls for better oxygen barrier.

Read more less

#6 stopper - with 3/8 inch hole. Top diameter 1.25 inches (32 mm), bottom diameter 1.03 inches (26 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. For use with our 1 gallon glass jars (FE300). To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).

Read more less

With the FermZilla Pressure Kit you can ferment under pressure, carbonate, and serve without ever needing to move your beer out of the fermenter. The kit inlcudes two plastic female threaded ball lock fittings with barbs, which thread onto the existing openings atop the FermZilla's lid. For the beverage out, you'll have a silicone dip tube with stainless steel float, allowing you to always draw from the clearest beer at the top of the tank. Pick up the Pressure Kit and turn your FermZilla into a true unitank! Includes one red and one yellow ball lock cap to help differentiate which one is being used for liquid and which one for gas. Either color can be used for either function. The silicone dip tube is 31" long. It will work perfectly as is for the 55L FermZilla. For the 27L model we recommend cutting the dip tube shorter to remove unwanted slack. With the optional Floating Dip Tube Filter, you can prevent hop material and other solids from ever entering the dip tube. Especially handy when you're pulling samples mid-fermentation! Fermenting Under Pressure: The pressure kit allows for fermenting under pressure, which will reduce esters and fusel alcohol production. This means you can ferment at warmer temperatures than you normally would, even making lagers at room temperature. Most commerical beer is fermented under pressure simply due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the distinct differences between homebrewing and brewing on a commercial scale. The FermZilla's lid already comes with a built-in pressure relief valve that will blow at 35 psi; the pressure kit simply allows you to add CO2 through the ball lock fitting. We strongly recommend that you also purchase an adjustable pressure relief valve, or spunding valve, which allows you to set a lower pressure. It's always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure.   Carbonating, Transferring, and Serving: When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using a spunding valve. This means you can eliminate kegging and serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Attach a beer line from the FermZilla's bev out to your keg and enjoy the easiest kegging experience ever.  You can also choose to send carbonated beer through a beer filter on the way to your keg.  When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator.     Eliminate Oxidation: Since the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock.   Key Features: Ferment beer under pressure to reduce ester and fusel alcohol production Always draw clear beer with the floating dip tube Keg beer that has already been carbonated Use CO2 to push beer into a keg or through a filter into a keg Eliminate kegging altogether by carbonating and serving directly from the FermZilla Installation Note: For best performance, ensure there is not an excess amount of slack when the silicone dip tube is installed and shorten it if needed. With the floating dip tube installed on your empty FermZilla, you ideally want the dip tube to hang freely with just enough length for the end of the dup tube to touch the bottom of the tank. Please note: pressure kit does not include the lid pictured in the example photo. The ball locks and floating dip tube are installed on the FermZilla's existing lid.

Read more less

Smooth, ribless design prevents yeast and bacteria buildup, making sanitation a breeze Punted bottom and conical top promote sediment collection and reduce oxidation during storage Extra-wide 4" mouth opening simplifies filling, additions, and cleaning Constructed from heavy-duty, virgin PET plastic without plasticizers Made with food-grade and BPA-free materials The Fermonster is a brand new fermenter designed specifically for fermentation. MoreBeer! gave product feedback for over 2 years of development and we think they nailed the design. The large lid allows for easy filling and makes hop or oak additions a breeze. The smooth sides are fantastic for sanitization - no ribs or texture to collect yeast or bacteria.  The large 7 gallon size was designed to provide ample space for fermentation and you'll find the molded in volume markers super handy for accurate filling. The punted bottom allows sediment to collect to the sides so that you can siphon liquid from the center.  Because they are made from virgin PET plastic they nearly unbreakable and a lot safer than similar glass carboys. Also notice the conical top which reduces surface area if you plan to store beer or wine long term.   Made from heavy PET plastic, the same material used in 2 L soda bottles, which is nearly impermeable to oxygen penetration.  Due to the thickness of the material and the overall geometry the Fermonster does not require ribs or dimples for stability.  That results in a super smooth interior surface that reduces yeast and sediment buildup making it the easiest to clean, most sanitary PET carboy on the market.  The huge 4" opening makes filling a breeze, and cleanup is as easy as wiping down the inside.  The 7 gallon volume is a monster of a fermenter, reducing blowoff issues seen with standard 5 and 6 gallon carboys. Fermonsters are easily moved by hand or consider using our Carboy Carrier for even greater ease of use. These fermentors are completely air-tight and the lids sealed tight with an O-Ring.  Additional O-Rings and Lids both with and without holes are available for purchase, see our You Might Also Need items below. Features: 4" inner diameter wide mouth carboy - easy to clean! Food grade PET plastic construction is nearly impermeable to oxygen penetration No hard to clean dimples or ribs Volume Markers at 5, 6, and 7 Gallons Punted bottom O-Ring and Lid with one hole is included (Fits #10 Stopper) Additional O-Rings and Lids available Weight: 1.5 lbs Temperature Limit: 140° F Height: 20.9 inches Diameter: 11.3 inches Completely taste and odor free Perfect for Beer, Wine, Cider, Mead, Kombucha or any other fermented beverage! Thick walls for better oxygen barrier.

Read more less

Upgrade your home brewery with an innovative, Stainless Steel, 7 Gallon Brew Bucket™ Fermenter!  You will enjoy many of the benefits of a stainless conical fermenter but at a fraction of the cost and you are going to love how easy it is to use!  Made by Ss Brewing Technologies from polished 304 Stainless Steel, the Brew Bucket™ fermentor is not only functional it is downright beautiful. At MoreBeer!  we know brewing equipment and we truly believe this is a piece of equipment you are going to enjoy using every brew day. We inspected and used the Brew Bucket™ and one of the most unique features that stood out is that the Brew Bucket can be stacked during fermentation, even with an airlock attached. We also like the conical bottom that allows trub to settle out in a concentrated space that minimizes the surface area of the trub that is in contact with your beer.  The included Patent Pending Rotating Racking Valve is also a brilliantly simple design allowing you to rotate the racking arm inside the Brew Bucket down during fermentation to minimize trub, and later up to get clear beer when racking!   Etched Volume Markers on the inside were super handy when filling and display in both Liters and Gallons. The build quality is really amazing for the price. Welds are clean. The lid is strong and the spring loaded lid hatches are solid.  The lid includes a removable, molded silicone gasket that ensures an airtight seal.  We love an airtight seal so that we can be sure to see the airlock working.  The welded on stainless handles make the BrewBucket fermentor super easy to move.  Overall: Very functional, easy-to-use, will last a lifetime, and looks amazing. Lets make some beer! Features: Certified Food Grade 304 Stainless Steel Construction Patent Pending Stainless Rotating Racking Valve 6.95 gal Max Capacity 40° Conical Bottom for Trub Trapping Nests for Storage, Stacks for Ferment! Molded Silicone Lid Gasket Spring Loaded Lid Clamps for Airtight Lid Seal Offset Airlock Hole includes Silicone Stopper Gallon & Liter Markers inside for visual volume assessment Stainless construction resists damage and is easy to clean 21” Height x 13” Width 10 lbs Note: 1/2" Silicone fits into the lid hole for use as a blowoff.  3/8" ID tubing is perfect for racking beer from the BrewBucket's valve.

Read more less