Beer Brewing Equipment & Supplies

Translucent, food-grade tubing temperature rated to 500F. Odorless, tasteless, and inert Silicone tubing is FDA food-grade approved from -100F to 500F. Translucent natural color allows you to see the flow. The perfect tubing for building a personal brewery, especially for any time that the wort in contact with tubing will be above 180F. This tubing is not designed to hold pressures above 20psi. It works great with our magnetic drive pumps such as a March or Chugger pump, but we do not recommend it with a impeller pump or for use with household water pressure. Platinum Cured Quantity ordered will be shipped as multiple pre-cut lengths. Maximum length available is 100 ft. *Will burst at 30 PSI at 70F.  

Read more less

Small hose clamp suitable for 3/16" to 5/8" OD tubing Go-to clamp for anywhere you need to secure tubing Made from stainless steel These Stainless Steel small hose clamps are perfect to keep around as your go-to clamp. Use them anywhere you want to be sure your tubing will stay connected. They are perfect for silicone hoses and hooking up quick disconnects, pumps, or on any system that may need a tight seal. These stainless clamps tighten up better than cheaper ones, and the stainless steel won’t corrode. It’s handy to keep a few spares around, just in case.  Our small clamps will fit hoses with 3/16" through 5/8" OD.

Read more less

This tubing is so much better than the standard tubing most brewers start with. Silicone Tubing is odorless, tasteless, and is NSF approved as food-grade at temperatures from -100F to 500F. The translucent color allows you to see your wort flowing. It withstands high heat, which is great for any time that the wort in contact with tubing will be above 180F, which is the temperature threshold for most vinyl tubing. It doesn’t slip off of your equipment, never kinks, and easily slides on and off of barbed fittings without deforming or leaking. It is so easy to work with that once you’ve tried it on one piece of your equipment, you’ll want to upgrade your whole setup!    3/8" ID 5/8" OD Platinum Cured   Not designed to hold pressures above 20 psi. Will burst at 30 psi at 70F.    

Read more less

Universal stoppers have a longer taper to help produce a better fit and a snug seal, and a lip which prevents them from falling into your container. Available with a 3/8 inch hole for an airlock, or solid with no hole. #10 size is recommended for PET carboys.

Read more less

Thin walled tubing perfect for siphoning or tranferring liquids when not under pressure. This is the most common size hose for homebrewing that you would need to fit onto the plastic spigots (FE347), 3/8'' OD bottle fillers, and the 3/8'' OD racking canes. 3/8" ID, 1/2" OD 1/8" thick wall  

Read more less

Accurately measure your starting and finishing gravity in beer or wine Triple scaled in specific gravity, potential alcohol, and Brix Comes with storage tube and directions Hydrometers are one of the most necessary tools in homebrewing. Our Triple Scale Hydrometer allows you to read your gravity, potential alcohol content, and brix. A hydrometer is perhaps the most essential piece of measuring & testing equipment in any home brewery. Used it at every stage of brew to keep up with the health and progress of your brew.  This convenient hydrometer features three scales--specific gravity, potential alcohol and brix--and is handy for both brewing and winemaking. It measures 9 inches long and comes with complete, detailed instructions for proper use.  Scale Ranges: Specific Gravity: 0.982 - 1.160 Potential Alcohol: 0-20% Brix: -4 - 35  

Read more less

The perfect size for taking hydrometer readings of your home brew--large enough to get a good reading, but small enough to not waste that precious beer!   Two piece molded plastic allows for easy cleaning. Will work with any of our hydrometers except the specialized +5/-5 Brix wine hydrometer.    

Read more less

With the FermZilla Pressure Kit you can ferment under pressure, carbonate, and serve without ever needing to move your beer out of the fermenter. The kit inlcudes two stainless female threaded ball lock fittings with barbs, which thread onto the existing openings atop the FermZilla's lid. For the beverage out, you'll have a silicone dip tube with stainless steel float, allowing you to always draw from the clearest beer at the top of the tank. Pick up the Pressure Kit and turn your FermZilla into a true unitank! The silicone dip tube is 31" long. It will work perfectly as is for the 55L FermZilla. For the 27L model we recommend cutting the dip tube shorter to remove unwanted slack. With the optional Floating Dip Tube Filter, you can prevent hop material and other solids from ever entering the dip tube. Especially handy when you're pulling samples mid-fermentation! Fermenting Under Pressure: The pressure kit allows for fermenting under pressure, which will reduce esters and fusel alcohol production. This means you can ferment at warmer temperatures than you normally would, even making lagers at room temperature. Most commerical beer is fermented under pressure simply due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the distinct differences between homebrewing and brewing on a commercial scale. The FermZilla's lid already comes with a built-in pressure relief valve that will blow at 35 psi; the pressure kit simply allows you to add CO2 through the ball lock fitting. We strongly recommend that you also purchase an adjustable pressure relief valve, or spunding valve, which allows you to set a lower pressure. It's always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure.   Carbonating, Transferring, and Serving: When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using a spunding valve. This means you can eliminate kegging and serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Attach a beer line from the FermZilla's bev out to your keg and enjoy the easiest kegging experience ever.  You can also choose to send carbonated beer through a beer filter on the way to your keg.  When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator.     Eliminate Oxidation: Since the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock.   Key Features: Ferment beer under pressure to reduce ester and fusel alcohol production Always draw clear beer with the floating dip tube Keg beer that has already been carbonated Use CO2 to push beer into a keg or through a filter into a keg Eliminate kegging altogether by carbonating and serving directly from the FermZilla Installation Note: For best performance, ensure there is not an excess amount of slack when the silicone dip tube is installed and shorten it if needed. With the floating dip tube installed on your empty FermZilla, you ideally want the dip tube to hang freely with just enough length for the end of the dup tube to touch the bottom of the tank. Please note: pressure kit does not include the lid pictured in the example photo. The ball locks and floating dip tube are installed on the FermZilla's existing lid.

Read more less

A definite upgrade over a standard hydrometer, this deluxe hydrometer also includes a built in thermometer that allows you to take both a gravity and temperature reading at the same time. It is a simple but key upgrade that you will be glad you have everytime you take a reading.   Based on the temperature, an also built in chart then tells you how many points you need to add or subtract from your gravity to get a true reading.  Accurate gravity readings are pretty key for consistent brewing.      Like our basic model, this deluxe hydrometer also features three scales - Specific Gravity, Potential Alcohol and Brix (Balling). 

Read more less

Water chemistry is key to brewing the best beer possible, and that's where a pH meter becomes an essential tool Measure your strike water's pH and make informed brewing salt additions to provide the ideal environment for enzymatic activity during the mash Digital display is easy-to-read and provides instant test results—no need to do a color comparison like with pH strips Automatic Temperature Compensation adjusts the results based on the temperature of the sample so you don't need to cool the sample before taking a reading Electrode is protected by a waterproof cap so your storage solution won't evaporate and dry out the electrode The KegLand pH Meter will get you a very accurate reading with its 0.01 pH resolution. The calibration process couldn't be easier to perform, just place the probe in the buffer solution closest to pH of the sample you'll be testing and press the button! This pH meter also includes ATC (Automatic Temperature Compensation) so you don't have to get your sample all the way down to room temperature before you take your reading.  3-point calibration allows this unit to be calibrated at three different standard levels - 4.00, 6.86 or 9.18. These standards are included with the pH meter, and refill packs are also available. The pH meter features a replaceable probe in case yours is lost or damaged. Homebrewing can be a tough environment for your pH probe so we feel you shouldn't have to buy a whole new pH meter everytime your probe breaks. The cap that holds the probe storage solution has a very tight seal and should prevent your probe from drying out while not in use. Don't worry about getting this meter wet either, because the entire unit is waterproof! Features: Replaceable probe ATC (Automatic Temperature Compensation) Waterproof electrode cap Accurate to 0.01 pH Easy 3 point calibration LR44/AG13 batteries included Kegland Part Number: KL04169 NOTE: Upon first time use prior to calibration, rehydration of the electrode with MT624B is essential to get an accurate reading for correct calibration.

Read more less

If you’re a serious homebrewer, you know the importance of proper pH during the brewing process. Use these calibration solutions to keep your pH meter reading accurately before each brew.   Includes 4oz each of 4.00 and 7.00 buffers. We package these solutions from bulk quantities to get you the best pricing. For testing, pour buffers into a small glass. You do not want to stick the probe of the pH meter into the buffer jars directly because you will eventually sacrifice the accuracy of your buffers.   Expires after 6 months if unopened. Expires after 3 months if opened.   Click here for a PDF of the MoreManual on proper pH Meter care.

Read more less

#7 stopper - with 3/8 inch hole. Top diameter 1.43 inches (36.3 mm), bottom diameter 1.19 inches (30 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).

Read more less

Use for the 1/2'' OD racking cane and 1/2'' OD bottle fillers.  

Read more less

We've seen a lot of all-in-one systems over the years, but none are as feature-packed and affordable as the BrewZilla. While other units simply maintain your set temperature, the BrewZilla features a sophisticated digital controller which can be programmed with a full mash schedule, executing each step automatically. The built-in pump will continuously recirculate wort during the mash for more even heat distribution and higher efficiency, but thanks to the integrated camlock fitting, it has even more functionality. Add the optional whirlpool arm to make your late hop additions pop and speed up chilling time, or connect a camlock fitting and tubing to transfer wort to your fermenter. These are just a couple of reasons why MoreBeer! loves the BrewZilla, but there are so many More! Our Top 10 Favorite Features: Sophisticated digital controller capable of programmed mash steps, boil addition timers and delayed start Built-in pump for constant recirculation during mash or whirlpooling and transferring with optional accessories Full depth malt pipe for higher mash efficiency and capable of running small batches without a pricey adapter Multiple power modes to cover each step of the brew day – low power to gently heat your mash up to full power for a rolling boil Wort chiller included! Perfectly sized for this system and adds even more value to your purchase of the BrewZilla High capacity brewhouse – with a volume of over 9 gallons, you can fit more grain and more wort to make MoreBeer! Single wall design doesn't trap in heat – chill your wort quickly after the boil! Super convenient bottom handle makes lifting/pouring a breeze Rubber feet keep the boiler lifted off the ground and safely above any spills that may occur Affordable! This is the best price for an all-in-one brewing system you'll find, period. If you want to jump into all grain brewing right from your first batch, or as an upgrade from malt extract brewing, the BrewZilla is a complete turn key solution. The BrewZilla is an all-in-one electric brewery that has built-in elements for heating and boiling, programmable mash schedule and delayed start, a built-in pump for recirculation, an onboard water resistant control panel for setting and monitoring temperatures, a removable grain basket, and a built-in spigot for transferring. It is extremely portable and uses 110V power so it can be used nearly anywhere. The V3.1.1 unit features an upgraded main circuit board that changes how the automatic step mashing functions. Now when moving from step to step, the timer for each step will not begin counting down until the programmed temperature is reached. This means more accurate mash schedules than ever before! The new board also introduces boil addition timers so you'll never miss the mark for hop additions. To get the Wort Chiller Connection Kit for free, add the item to your cart along with the BrewZilla and use code ZILLAKIT at checkout. New accessory! Check out the BrewZilla Whirlpool Arm, which uses the unit's internal pump to recirculate and spin the wort, improving hop extraction and chill times. No more stirring! Automatic Step Mashing & Delayed Start!  One of the coolest features of the BrewZilla is the ability to program the unit with up to 6 individual temperatures and durations so you can step mash precisely how you desire. Simply press the "S1-S6" button to select the stage you want to adjust, and use the temp, time and +/- buttons to program the stage. If you have less than 6 stages in your mash schedule, program the stages you want to skip with 00:00 as the time and the controller will automatically move on to the next step. When all the stages are complete, the unit will sound an alarm and hold the last set temperature. The programmable stages can also be used to set a delayed start of up to 23 hours in advance so that you can have your water hot and ready to go when you get home from work or wake up in the morning. In order to do this, fill the unit with strike water and program the controller with two steps. Step 1 should be programmed at a temperature lower than the unheated strike water (so the elements will remain off), and the duration should be programmed for however long you want the delay. Then program Step 2 with your desired strike water temperature and a duration of 1-2 hours, giving the BrewZilla ample time to heat up and giving you a margin of error in case you hit the snooze button the morning of brew day. Recirculating Mash with Full Depth Malt Pipe The built-in magnetic drive pump easily recirculates wort during the mash. We recommend getting some silicone tubing to go with the recirculation arm. This allows you more control over the recirculation and you can then use the pump to transfer your wort to your fermenter. As with any mash, be sure to stir your grain very thoroughly after mashing-in so you start out with an even temperature throughout the grain bed. Some competing models advertise their perforated malt pipes as "high flow", but what they don't mention is how this affects efficiency. When recirculating the mash, wort will escape through the side perforations rather than passing through the grain at the bottom-most end of the malt pipe which can lead to lower efficiency. The BrewZilla's malt pipe is designed so that recirculating wort must pass through the entire grain bed before escaping through the false bottom and being pumped over the top of the grain bed again. If you're worried about the flow rate, simply add a pound or two of rice hulls to your grain bill. This is especially recommended when brewing with a high level of wheat, oat, or flaked grains. Power & Heating Control Dual heating elements run off of a single 110 volt plug and have individual switches allowing for more control over the heating process. One element is 1000 watts and the other is 500 for a combined 1500 watts! Use both when you need to ramp up the temperature quickly either at the start to get to your mash temp or to go from your mash temp to boiling. Use only one of the elements when you want to hold a temperature. We highly recommend adding the optional BrewZilla Neoprene Jacket to help reduce heating times and maintain a more vigorous boil. The extra thick neoprene jacket is custom designed to insulate the entire kettle portion of the BrewZilla while staying out of the way of the ball valve and handles. The jacket can help you acheive up to 10% faster heat up times and cut heat loss from the boiler in half. And when it comes time to cool your wort after the boil, simply remove the jacket! While other units boast a double wall design for better heat retention, this actually becomes a disadvantage when it comes to chilling. The digital control panel makes it easy to see the current temperature and set the temperature you want. The digital controller is also water resistant so don't worry about spills or some water dripping down the side. This controller is built for brewing! The brewery also includes a stainless steel malt pipe with false bottom allowing you to easily shift from mash tun to boil kettle during your brew day. The malt pipe includes a handle to lift it out and tabs at the base so you can set the malt pipe over the kettle to let the wort drain out. It also has feet at its base to raise the malt pipe slightly off the base and help prevent clogging. The included stainless steel wort chiller is shipped with bare ends so you can set it up for your situation. We list below the most common tubing and fittings to connect to a hose, hose bib, or faucet.   What MoreBeer! loves about this product: Homebrewing is trending in the direction of all-in-one, all-grain brewing systems and the BrewZilla is the ultimate value. The cost is half of the next comparable system with programmable mash steps and nearly the same as buying converted coolers and a kettle. We've brewed on all the systems and we can truly say the BrewZilla is the easiest to use. We feel confident that a lot of first time brewers could buy this and use it with ease. At the same time quite a few of our experienced, all-grain brewing staff are buying it to brew at home. The unit is extremely compact because the pump is built-in to the bottom of the unit. You can move it around with ease which makes it perfect for guys and gals that have space constraints. Someone on the team also mentioned how they like that you can drain it via gravity without having to use the pump. All in all a great buy and highly recommended. Please note you will need a few extra pieces of hardware to connect the wort chiller and at least 2' of silicone tubing for the sparge. Use the Pump for More Than Just Recirculation! One of the surprisingly handy features of the BrewZilla is that the recirculation pipe features a female camlock. This allows you to hook up other accessories and use the unit's pump for more than just recirculating wort. With a male camlock and silicone tubing, for example, you can use the internal pump to push wort through a plate chiller or counterflow chiller. Check out our selection of camlock fittings here.    Features: Gen 3.1.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons Digital temperature controller Automatic step mashing with 6 programmable stages 110V power and plug Dual heating elements for total control (1000 watts and 500 watts) Stainless steel 1/2 inch ball valve for draining (dont have to use the pump) Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Magnetic drive pump for recirculation Recirculation arm Bottom handle for easy lifting and pouring Upgraded rocker switches Rubber feet Temperature reads in °F or °C (press and hold temp button for several seconds to adjust) 32.75 in H (with recirculation arm) x 12.5 in D Recommended max. grain bill - 18 lbs Recommended min. grain bill - 8 lbs AlcoEngine Still ready with the purchase of a Distillation Lid You Will Need: 2' of H985 1/2" ID Silicone tubing for sparging and draining. To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950 hose clamps and (1) brass hose by thread adaptor (H508). These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout. Note: The manual references an element for a different market.  This unit comes with two heating elements for a total of 1,500 watts. Kegland Part Number: KL05838  

Read more less

Achieve consistent and optimal fermentation temperatures with the FermWrap Fermentation Heater. This flexible and easy-to-use unit wraps snugly around your fermenter, providing gentle and controlled heat. Use alone or simply plug into the 110V heatnig plug on most popular temp controllers Provides gentle, even heating with 40 watts spread over almost two square feet Keep your yeast happy and your ferment warm during those cold winter months with this flexible heater wrap! Don't be fooled by imitators and cheap knock-offs, this is the original FermWrap that has been produced by Fermentap for over a decade. Unlike those old heater belts, the FermWrap covers a wide area of your carboy or fermentation vessel, promoting an even heat distribution. Using tape to adhere, the FermWrap can be attached directly to your fermenter, or can be used to heat the space in a box (or refrigerator) that the fermenter is in. Depending on your configuration and insulation, you can increase the temperature of your ferment from 5-20°F. This differential can be increased by using the BrewBuilt™ Neoprene Carboy Sleeve.   With 40 watts of heat spread over almost two square feet, it provides gentle, even heating.   For more precise results, we recommend a temp controller and carboy thermowell. The controller will monitor the fermentation temp and only power on the FermWrap if the temperature drops below your set point. For the ultimate level of control, we recommend pairing it with the BrewBuilt CoolStix™ to provide cooling. With both accessories plugged into the temp controller, you'll get cooling or heating whenever you need it.   Specs: 40 watts 115V 11" H x 25" W   Item does not include carboy as pictured.   Kegland Part number: KL06255 

Read more less

You will love the versatility of this stopper!   The Universal Stopper with Hole fits a 2.8, 3, 5, 6, or 6.5 gallon glass carboy. Also fits our 500ml Erlenmeyer flask, and can be flipped over and used in most bottles! Made with a longer taper from a different material from standard stoppers to minimize popping out when wet.   Please Note: This stopper will not fit in plastic carboys, Better Bottles or Speidel Plastic Fermenters.

Read more less

If you want to take a gravity reading of your latest brew, this extra-tall Hydrometer Jar will make the job easy.    This extra-tall 14" Hydrometer Jar is perfect for a brix hydrometer. Because the jar is clear, you’ll be able to easily see the markings on the hydrometer and the color of your brew.

Read more less

The Temp Twister Cooling Coil is the ideal option for maintaining fermentation temperatures in any model FermZilla. Use an IceMaster Glycol Chiller or ice bath with submersible pump to push coolant through the coil when temps get too hot. Designed for the FermZilla but can can be used with virtually any fermenter that has an opening diameter of 4-3/8" or wider. The inlet and outlet are extra long so the coil can be used with every sized FermZilla. In order to cut them to an appropriate length for your application, we recommend this compact pipe cutter. To install, simply drill two 22 mm (approx. 7/8") holes into the lid of the fermenter and use the included Duotight bulkhead fittings to attach the coil to the lid. The FermZilla will still be pressurizable after installing the Temp Twister, just be careful to drill the holes no wider than needed to fit the Duotight bulkheads. If you're using the Temp Twister with EVABarrier tubing, we suggest adding 2 x DUO112 to your order to help route your inlet and outlet lines. Specifications: Coil Diameter - 4.33" Coil Height - 14" Overall Length - 26.75" Tubing Diameter - 3/8" OD Made from 304 Stainless Steel Includes 2 x 9.5 mm Duotight bulkheads Kegland Part number: KL14618  

Read more less

The lowest price Pressuizable fermentor out there Prefect for most ales that ferment in 2 weeks or less Super smooth PET makes cleaning very easy Transfer to your keg closed and under pressure, oxygen free PET is a better oxygen barrier than fermentors made of HDPE Super lightweight yet strong and shatterproof The FermZilla All Rounder is the most affordable pressurizable fermenter on the market. Although it doesn't feature a dump valve like the FermZilla Conical, the All Rounder carries the same pressure rating, making it an absolute steal if you're looking to ferment under pressure, perform pressure transfers, or want to carbonate and serve directly from the fermenter. The All Rounder is made from super smooth PET that's easy to clean, and the simple design means no nooks or crannies for microbes to hide. With a 4.75" lid opening, you'll have no trouble getting your arm inside to scrub away stubborn krausen rings. As with all FermZilla fermenters, the lid features molded drill locations that make installing accessories like a thermowell or Temp Twister Cooling Coil a breeze. In order to unlock the full potential of the All Rounder, you'll want to pick up the 55L FermZilla Pressure Kit. The silicone dip tube will be a little long, but you can cut it shorter to the appropriate length. The pressure kit is available with either stainless or plastic ball lock caps. Why MoreBeer! loves the All Rounder FermZilla: Super smooth PET makes cleaning very easy. Pressure rated lid and PET material make for a better oxygen barrier than fermenters made of HDPE. Lightweight and easy to move around, yet strong enough to be considered shatterproof. The 4.75" lid opening makes it easy to get your arm inside and clean after use. The lid is designed for the easy installation of accessories such as a thermowell or cooling coil. Price! A pressurizable fermenter in this price range is an incredible value, and it opens the door for many cold-side processes that can't be done in a normal carboy or plastic fermenter. What's Included: FermZilla 30L All Rounder Fermenter Stainless Steel Stand Stainless Steel Handle Top Lid with PRV (35 psi) 3-Piece Airlock Adhesive Thermometer Graduation Sticker Specs: 30 L (7.9 gal) Total Volume Pressure Rated to 2.5 Bar (36.2 psi) Height in Stand - 21.7" Height w/ Airlock - 24.2" Tank Diameter - 13.9"  Lid & Collection Container Ports - 28 mm PCO 1881 threads Temperature Rating: When not under pressure, do not expose to liquids above 131°F When under pressure, do not expose to any temperatures above 95°F* *Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years. Kegland Part number: KL15189   NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.

Read more less

Functions the same as a standard Hose Clamp, however rather than needing to find a screwdriver (or dime!) for every adjustment you can easily tighten by hand. As an added bonus, this also has a significantly smoother inside to the clamp, which will not tear up your tubing nearly as much as a standard hose clamp!  Ideal for situations where you need to remove tubing from fittings to sanitize. Please note, as the reviews will also tell you, this is a clamp that will fit 1/2" OD tubing. If you are looking for a clamp for 1/2" ID (with 3/4" OD) choose the H955 clamp. 

Read more less

The Inkbird dual stage temperature controller is an easy to use and economical controller that is perfect for home brewing. Inkbird controllers allow you to control both heating and cooling, and set independent differentials for each to keep the exact temperature you need. The Ink bird ITC-308S controller performs many of the same functions as the Ranco or Johnson but at a more affordable price, making it a great alternative for temperature control.  Aside from brewing uses, this is a great dual relay output temperature controller for cooking (use in a smoker or bbq), home growing (heat mats for seedlings, climate control), or any other DIY project you come up with! Features: Simple plug and play design with user friendly LED interface Dual stage ITC-308 - control both heating and cooling Adjustable Heating/Cooling differential 1000W max power Celsius or Fahrenheit High and low temperature and sensor fault alarms Can control temperatures of -58° F through 210° F (-50° C - 99° C) Body Dimensions: 5.5 in x 2.7 in x 1.3 in

Read more less

Functions the same as a standard Hose Clamp, however rather than needing to find a screwdriver (or dime!) for every adjustment you can easily tighten by hand. As an added bonus, this also has a significantly smoother inside to the clamp, which will not tear up your tubing nearly as much as a standard hose clamp! Ideal for situations where you need to remove tubing from fittings to sanitize.

Read more less

This 24-inch stainless mash paddle is the perfect size for most 5-gallon batch applications, and is well-suited for use with the BrewZilla, DigiBoil, Grainfather or Braumeister brewing units. Slotted paddle face gives you less resistance while stirring in extract or breaking up dough balls. Features a hole located at the handle end so you can hang up the paddle when not in use. 24" overall length, paddle is 4.5" long Paddle tapers from 2.5" to 1.5" wide 1/4" hanging hole 304 stainless steel construction   Kegland Part Number: KL03810

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in late November.   Stop lifting buckets, kettles, and fermenters or relying on gravity for transfers! Brew pumps unlock a world of brewing processes otherwise unavailable—create a return loop for whirlpooling in kettle during post boil hop additions Stainless steel pump head comes standard—the ideal choice for attaching quick disconnects, camlocks, and other stainless fittings Built-in flow control valve allows for direct flow adjustment on the pump head and eliminates the need to add an additional ball valve Corny keg style pull ring PRV makes it easy to bleed the pump head of air bubbles and prime the pump Tri-clamp pump head can be rotated to your preferred orientation and disassembles quickly for cleaning between uses Imagine a brewing pump that eliminates cavitation, is easy to clean, has a built in valve, and is quiet. Introducing The RipTide pump from Blichmann Engineering, the first pump designed specifically for homebrewing. We love this brew pump. Like a brewer wired on coffee, let us rattle off some of our favorite features.  First, the pull style relief valve that allows air to exit the pump head so the impeller won't cavitate is a genius addition. Our next favorite feature is the bad-ass, built-in flow control valve so you don't have to add additional ball-valves. While we dont manually clean our pumps very often we like the idea that we can easily do that with the clover clamp style connection. That might be particularly important if you are transferring cool wort where extra sanitation might make a difference.  Equally cool is the noise, or lack thereof, when operating. It just wears on you to hear your pump grinding away all day. The RipTide pump isn't silent, but it is much quieter.  And to top it all off we like the mounting base and the extra long 9' cord. 9' gets the plug connection a few feet away from where we are brewing and less likely to be exposed to water - a simple upgrade that is really nice.  Oh, and we almost forgot the power switch which is always a nice feature on something electric! All in all this is a no brainer upgrade for the difference in cost. Features: Strong rare earth magnets and a curved blade impeller provide 7 GPM and up to 21 ft of lift Tri-Clamp head disassembles easily for cleaning 1/2" NPT inlet and outlet Motor is enclosed in a splash proof and super quiet case Rotatable stainless steel head Integrated air release vent allows you to easily prime the pump everytime without those frustrating air bubbles and cavitation Linear flow valve provided for excellent flow control Power switch on base 10 ft. long power cord with 120V plug

Read more less

Use these high quality, food-grade quick-disconnects on your gas and beer tubing lines. Uses might include the following: * On a gas system to unhook your tank and regulator from your manifold so you take it with you. * On a beer line to easily switch between ball lock, pin-lock, or a commercial tap * On a counter-pressure bottle filler to be able to easily connect to your existing gas line. This plastic quick disconnect set features 1/4" barb which can be used with tubing ID 3/16" through 5/16". The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you need not worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade buna-n.

Read more less

This stainless steel hop tube is ideal for keeping kettle additions from clogging your pump or heat exchanger, and works perfectly for dry hopping in a keg or wide-mouth fermenter. Holds approximately 5 oz of pellet hops, allowing some space to permit full extraction of the hop oils. The stainless chain makes it the perfect partner to our Corny Keg Lid with Welded Tab. Hang the tube inside your keg for post fermentation hop, fruit, wood chip, or spice additions. When it's time to remove the hops/adjuncts simply pull the tube out. Works great for timing exactly how long your beer sits on the hops, oak, or other flavoring addition. 2.6" diameter 11.8" tall Made from 304 stainless steel Kegland Part Number: KL05210

Read more less

Grab everything you need to ferment under pressure with the FermZilla All Rounder and we'll toss in the BlowTie Spunding Valve for FREE! This kit includes the 30L FermZilla All Rounder, ball lock cap adapters for the lid and collection container, floating dip tube with filter attachment, and the BlowTie 2 ball lock spunding valve. Everything you need to ferment under pressure, carbonate in vessel, and pressure transfer. The FermZilla All Rounder is the most affordable pressurizable fermenter on the market. Although it doesn't feature a dump valve like the FermZilla Conical, the All Rounder carries the same pressure rating, making it an absolute steal if you're looking to ferment under pressure, perform pressure transfers, or want to carbonate and serve directly from the fermenter. The All Rounder is made from super smooth PET that's easy to clean, and the simple design means no nooks or crannies for microbes to hide. With a 4.75" lid opening, you'll have no trouble getting your arm inside to scrub away stubborn krausen rings. As with all FermZilla fermenters, the lid features molded drill locations that make installing accessories like a thermowell or Temp Twister Cooling Coil a breeze. Why MoreBeer! loves the All Rounder FermZilla: Super smooth PET makes cleaning very easy. Pressure rated lid and PET material make for a better oxygen barrier than fermenters made of HDPE. Lightweight and easy to move around, yet strong enough to be considered shatterproof. The 4.75" lid opening makes it easy to get your arm inside and clean after use. The lid is designed for the easy installation of accessories such as a thermowell or cooling coil. Price! A pressurizable fermenter in this price range is an incredible value, and it opens the door for many cold-side processes that can't be done in a normal carboy or plastic fermenter. What's Included: FermZilla 30L All Rounder Fermenter Stainless Steel Stand Stainless Steel Handle Top Lid with PRV (35 psi) 3-Piece Airlock Adhesive Thermometer (1) Red Ball Lock Carbonation Cap (1) Yellow Ball Lock Carbonation Cap Use one color for gas and one for liquid! Stainless Steel Float with Silicone Dip Tube Weighted Mesh Filter Attachment (KEG6571) All Rounder Stand Harness FREE BlowTie Spunding Valve FermZilla All Rounder Specs: 30 L (7.9 gal) Total Volume Pressure Rated to 2.5 Bar (36.2 psi) Height in Stand - 21.7" Height w/ Airlock - 24.2" Tank Diameter - 13.9"  Lid & Collection Container Ports - 28 mm PCO 1881 threads Temperature Rating: When not under pressure, do not expose to liquids above 131°F When under pressure, do not expose to any temperatures above 95°F* *Please note that the temperature rating for the PET tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer liquid into the tank below 131°F or to use hot liquids below this temp to clean the tank. When under pressure, you should make sure to keep your unit in an environment no hotter than 95°F and to keep your fermentation temperature below this temp as well. If you are using kveik yeast to ferment under pressure, we highly recommend using temperature control. Installation Note: For best performance with your Floating Dip Tube, ensure there is not an excess amount of slack when the silicone dip tube is installed and shorten it if needed. With the floating dip tube installed on your empty FermZilla, you ideally want the dip tube to hang freely with just enough length for the end of the dup tube to touch the bottom of the tank. NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.

Read more less

Heavy-duty HDPE plastic fermentation and stoarge tank Made from food-safe materials with extra thick walls to preserve the aroma of your beverage Rotating plastic spigot eliminates the need to use an auto-siphon or racking arm to transfer liquid Wide top port opening for easy cleaning Airlock & stopper included Made in Germany by Speidel The future is here today, and the future is HDPE Fermentation & Storage Tanks from Speidel. Made in Germany from nothing but undyed and food-safe plastic, these tanks are produced with particularly thick walls which preserves the aroma and the alcohol for a markedly long time. The stable carrying handles have been tried and tested for decades and are extremely durable. Are you tired of carboys? Hate siphoning to transfer? Wish you could ferment larger batches in a single container? Sick of lifting 50lbs by a small metal handle? Done with worrying about shattered glass, injury and lost product? Well then have we got the solution for you! These heavy duty plastic tanks offer a fantastic fermentation & storage solution at a great price. Key Features: Heavy duty HDPE construction is durable and resists oxygen transfer. None of the risks of working with glass. Small footprint makes them easy to store - take better advantage of the space you have to dedicate to wine & beer making. Built-in handles make these tanks easy to move, even when full. Large lid opening makes them easy to clean by hand - say goodbye to your carboy brush! All ports seal with gaskets and the vessel can be fully sealed for long-term storage. Includes a spigot and oversized 2-piece Speidel airlock. Designed and manufactured in Germany by Speidel, the makers of our legendary commercial wine tanks Suggested Applications: 12L: Perfect for storing small lots, making experimental batches and taking some of your beer or wine along with you to your next party. 20L: Ideal for secondary fermentation and storage of 5 gallon batches. 30L: The vessel for fermenting wine kits and 5 gallon batches of beer with plenty of headspace and no need for a blowoff tube. 60L: Perfect for fermenting larger batches of wine or 10 gallon batches of beer in a single container! Only 4" larger in diameter than a 6.5 gallon carboy! 120L: Ferment & Store large batches of anything - your creativity is the only limit! Approximate Dimensions: 13.5in Diameter x 18.5in Height (w/out airlock in place). Note - The maximum temperature that these plastic fermenters can handle is 140F. FAQ: Can filled containers be carried by the handles? Depending on the weight—barrels up to 30L are no problem—60L is the limit and should not be carried when completely full. The handles have a weight capacity of 30kg (66 lbs). Is there an upper limit on the alcohol content of the stored liquid? In principle, there is not. However, it should be noted that the higher the alcohol content, the faster the seals and, to a lesser extent, the tank itself will wear out. Up to what temperature can the containers be used? For short periods of time the containers can withstand temperatures of up to 80°C (176°F). This temperature should not be exceeded. For longer periods of time the containers can be used at temperatures up to 60°C (140°F).

Read more less

This plastic syringe is perfect for measuring out acid additions or other small amounts of liquid. Perfectly suitable for multiple uses in brewing and winemaking applications. Calibrated up to 10 ml. 1 ml is equal to 1 cc.   NOTE: The center nozzle syringe is not compatible with the Anton Paar EasyDens. You will need a syringe with offset nozzle.

Read more less

Now a scale that you can use to measure large amounts of hops and grains at home! This is a great addition to any home brewery!   This Electronic Grain Scale is capable of weighing a full sack of grain, and then some. This benchtop unit has a 55lb capacity, lifetime warranty, and a host of helpful features.    Features: Massive 55 lb (25 kg) capacity! Optional Backlight Feature Runs on 4 x C batteries or AC adaptor (included) Large Weigh Platform 8" x 6.5" Weighs in Pounds, Pounds:Ounces, Ounces, Kilograms, Grams Dual Range Weigh Design: 0-2 lbs x 0.1oz/0-1kg x 2g 2-55 lbs x 0.5oz/1kg-25kg x 10g Display is removable and attached to two foot cord for easy viewing of the display while using larger weighing vessels

Read more less

This Erlenmyer flask is huge, coming in at 5000 ml (5L!), making it the ideal vessel to make a large yeast starter for a 10+ gallon batch. The best brewers make large yeast starters to get their beer fermenting fast, and most of them do so in an Erlenmeyer flask. Large populations of active yeast help ensure flavorful beer free of off flavors. Because this flask is made from borosilicate glass you can move it from a boil into a cold water bath for cooling. This means you can do the whole process in one container, keeping it simple and helping to reduce the risk of contamination when transferring from one container to another. Double Boiler Method It is important for your safety to heat water in the flask with a heat source that distributes heat evenly. Morebeer! recommends using the "double boiler method." This process involves using a boiling water bath on the outside of the flask to heat up the water inside the flask. All you need is a kettle 3 gallons or larger. This process is much safer and efficient. If the flask should break or boil over, your kettle will be there to collect the contents, thus keeping your stove clean and keeping you safe. Safety First: Please take us up on a great deal - save $14.95 when you purchase a 5000ml flask and our BE300 5 gallon stainless steel kettle at the same time. Use Promo code SAFETY1 at checkout. Features Massive 5L (5000ML) Capacity Made from Borosilicate Glass (also known as Pyrex) Fantastic price for a flask of this size Produced for MoreBeer!   Why make a yeast starter? (from our FAQ) We build starters for 3 main reasons. First, to ensure yeast health. By making a starter 1-3 days in advance, you ensure that your yeast is healthy and strong and ready to do its job. Second, to create more yeast. By making the starter you will increase the cell count of the yeast, giving you a better chance of keeping bacteria's and wild yeasts from fermenting your wort. Third, if you are making high gravity beers. If you are making a high gravity beer (1.060+) you will need more yeast to start the ferment faster. High gravity beers will also finish more completely when you pitch ample quantities of yeast. In the lab world, these flasks are known as "Student Grade". Student grade flasks may have small scratches and air bubbles. A great flask for making yeast starters! For a stopper we recommend a size #8-9 (FE498 or FE499). Kegland Part Number: KL04008

Read more less

This tubing is so much better than the standard tubing most brewers start with. Silicone Tubing is odorless, tasteless, and is NSF approvedd as food-grade at temperatures from -100F to 500F. The translucent color allows you to see your wort flowing. It withstands high heat, which is great for any time that the wort in contact with tubing will be above 180F, which is the temperature threshold for most vinyl tubing. It doesn’t slip off of your equipment, never kinks, and easily slides on and off of barbed fittings without deforming or leaking. It is so easy to work with that once you’ve tried it on one piece of your equipment, you’ll want to upgrade your whole setup!    1/4" ID 7/16" OD Platinum Cured   Not designed to hold pressures above 20 psi. Will burst at 30 psi at 70F.    

Read more less

Feels like professional lab equipment and worth every penny Made by leading brand in beer analysis but at a home user price. Get Fast and Accurate gravity readings at any point in the brewing process even when alcohol is present Connects and displays via free app on your phone or tablet Based on oscillating u-tube principle which is known as world's most accurate testing method Anton Paar is a leading producer of analytical testing equipment for commercial breweries. Borrowing some technology from their high end machines, the EasyDens digital gravity/alcohol tester is designed for savvy homebrewers and small commercial breweries.  It is a precision gravity/density testing unit which can accurately read gravity with a tiny 2 ml sample at any point in the brewing process.  Alcohol % can also be tracked at any point during fermentation. The unit hooks up to your smartphone via Bluetooth and stores various fermentation "profiles" enabling you to track fermentation progress, alcohol levels, and help know when it's time to keg & drink your beer! Protect your device with the Silicone Protection Cover! See the documents tab for frequently asked questions about the Easy Dens. Features: Take a highly accurate gravity reading at any point in the brewing process even when alcohol is present. Very fast and simple to use Only uses 2ml of sample Automatic Temperature Compensation Connects and displays via free app on your phone or tablet Based on oscillating u-tube principle which is known as world's most accurate testing method Extremely durable Measures in specific gravity and alcohol can be determined with original reading App features graphing for gravity and alcohol App stores batch records (10) and can email a batch record as a .csv for saving. Mobile Apps: Free mobile apps for each application Brew Meister Proof Meister Wine Meister Features Quick measurement Fermentation tracking & visualization Continuous tracking ABV & Attenuation calculation based on OG & FG Automatic Temperature Compensation Stores batch records (unlimited amount included in premium) Data export Latest Updates to Meister Apps New batch design with a more detailed user interface Integrated beer style database Recipe creation and management Custom measurement values and labels ABV measurement for light beer, hard seltzer, and cider with the EasyDens & SmartRef Combo (in addition to existing support for standard and strong beer, wine, liqueur, and kombucha) Fermentation tracking for wine with SmartRef (previously only possible with EasyDens) Calorie determination for measurements with EasyDens, SmartRef, and the EasyDens & SmartRef Combo in Brew Meister and Wine Meister Tilt Hydrometer and RAPT Pill support in Brew Meister and Wine Meister Operating System Android & iOS Compatible with Apple Watch Features Free: Basic features and all measurement units Premium features: Free for one year New App Features: Direct ABV determination with the EasyDens & SmartRef Combo Beer: alcohol content (±0.5 %v/v), real extract (±0.2 %w/w), original gravity (±0.8 %w/w) and total extract (±2.0 g/L) Wine: alcohol content (±0.5 %v/v for wines up to 15% and ±1.0 %v/v for wines from 15 to 20 %v/v) Kombucha: alcohol content (±0.5 %v/v) Application specific in-app calculators Beer: color calculator, refractometer brix correction, ABV (OG/FG) calculator, converter for gravity, temperature & more Wine & Fruits: brix acid correction, residual sugar calculator, converter for gravity, temperature & more Coffee: extraction and TDS calculator Spirits: converter for gravity, temperature & more Compatible with RAPT Pill & Tilt Hydrometer Measurement data from these devices can be seamlessly integrated into your Brew Meister and Wine Meister batches Specifications: Measuring range Plato: -10 °P to +40 °P Brix: -10 °Bx to +80 °Bx Baumé: 0 °Bé to 45 °Bé Oechsle: -50 °Oe to +400 °Oe Klosterneuburger Mostwaage: 0 °KMW to 30 °KMW Babo: 0 °Babo to 30 °Babo Sugar concentration: 0 g/L to 500 g/L Alcohol: 0 %v/v to 100 %v/v Proof: 0 °Proof to 200 °Proof Specific Gravity: 0.7 to 1.2 Temperature: 5 °C to 30 °C / 41 °F to 86 °F Accuracy Plato: 0.3 °P Brix: 0.3 °Bx Baume: 0.3 °Bé Oechsle: 2 °Oe Klosterneuburger Mostwaage: 0.3 °KMW Babo: 0.3 °Babo Sugar concentration: 3 g/L Alcohol: 0.5 %v/v Proof: 1 °Proof Temperature: 0.2 °C / 0.4 °F Specific Gravity: 0.005* Digital resolution Plato: 0.1 °P Brix: 0.1 °Bx Baume: 0.1 °Bé Oechsle: 1 °Oe Klosterneuburger Mostwaage: 0.1 °KMW Babo: 0.1 °Babo Sugar concentration: 1 g/L Alcohol: 0.1 %v/v Proof: 1 °Proof Temperature: 0.1 °C (0.01 °F) Density: 0.001 g/cm³ General Sample volume approx. 2 mL Ambient temperature 5 °C to 35 °C / 41 °F to 95 °F Storage temperature 5 °C to 35 °C / 41 °F to 95 °F Humidity 5 % to 90 % relative air humidity, non-condensing Interface Bluetooth Low Energy Power supply Two 1.5 V LR6 AA alkaline batteries or two AA NiMH rechargeable batteries Battery operation lifetime: >40 hours Dimensions 101 mm x 58 mm x 44 mm (4 in x 2.3 in x 1.7 in) Weight (incl. batteries) approx. 190 g (0.42 lbs) Mobile Operating System Android 5.0 and higher; iOS 13.0 and higher Scope of supply EasyDens portable density meter, syringe 10 mL, batteries, adapters Luer, adapter Luer lock, waste hose, illustrated application description, certificate of compliance, safety guide Ingress protection IP65 according to IEC 60529 *accuracy for aqueous solutions (such as beer, wine, distilled spirits): 0.001  

Read more less

Functions the same as a standard Hose Clamp, however rather than needing to find a screwdriver (or dime!) for every adjustment you can easily tighten by hand. As an added bonus, this also has a significantly smoother inside to the clamp, which will not tear up your tubing nearly as much as a standard hose clamp! Ideal for situations where you need to remove tubing from fittings to sanitize.

Read more less

Keep your KegLand pH Meter's probe in great condition by storing it in this storage solution.  Letting your probe dry is the leading cause of degradation.  By leaving your pH meter in this solution when not in use, you will extend the life of your probe and maintain more accurate readings. KegLand Part Number: KL04183

Read more less