Electric Brewing

We've seen a lot of all-in-one systems over the years, but none are as feature-packed and affordable as the BrewZilla. While other units simply maintain your set temperature, the BrewZilla features a sophisticated digital controller which can be programmed with a full mash schedule, executing each step automatically. The built-in pump will continuously recirculate wort during the mash for more even heat distribution and higher efficiency, but thanks to the integrated camlock fitting, it has even more functionality. Add the optional whirlpool arm to make your late hop additions pop and speed up chilling time, or connect a camlock fitting and tubing to transfer wort to your fermenter. These are just a couple of reasons why MoreBeer! loves the BrewZilla, but there are so many More! Our Top 10 Favorite Features: Sophisticated digital controller capable of programmed mash steps, boil addition timers and delayed start Built-in pump for constant recirculation during mash or whirlpooling and transferring with optional accessories Full depth malt pipe for higher mash efficiency and capable of running small batches without a pricey adapter Multiple power modes to cover each step of the brew day – low power to gently heat your mash up to full power for a rolling boil Wort chiller included! Perfectly sized for this system and adds even more value to your purchase of the BrewZilla High capacity brewhouse – with a volume of over 9 gallons, you can fit more grain and more wort to make MoreBeer! Single wall design doesn't trap in heat – chill your wort quickly after the boil! Super convenient bottom handle makes lifting/pouring a breeze Rubber feet keep the boiler lifted off the ground and safely above any spills that may occur Affordable! This is the best price for an all-in-one brewing system you'll find, period. If you want to jump into all grain brewing right from your first batch, or as an upgrade from malt extract brewing, the BrewZilla is a complete turn key solution. The BrewZilla is an all-in-one electric brewery that has built-in elements for heating and boiling, programmable mash schedule and delayed start, a built-in pump for recirculation, an onboard water resistant control panel for setting and monitoring temperatures, a removable grain basket, and a built-in spigot for transferring. It is extremely portable and uses 110V power so it can be used nearly anywhere. The V3.1.1 unit features an upgraded main circuit board that changes how the automatic step mashing functions. Now when moving from step to step, the timer for each step will not begin counting down until the programmed temperature is reached. This means more accurate mash schedules than ever before! The new board also introduces boil addition timers so you'll never miss the mark for hop additions. To get the Wort Chiller Connection Kit for free, add the item to your cart along with the BrewZilla and use code ZILLAKIT at checkout. New accessory! Check out the BrewZilla Whirlpool Arm, which uses the unit's internal pump to recirculate and spin the wort, improving hop extraction and chill times. No more stirring! Automatic Step Mashing & Delayed Start!  One of the coolest features of the BrewZilla is the ability to program the unit with up to 6 individual temperatures and durations so you can step mash precisely how you desire. Simply press the "S1-S6" button to select the stage you want to adjust, and use the temp, time and +/- buttons to program the stage. If you have less than 6 stages in your mash schedule, program the stages you want to skip with 00:00 as the time and the controller will automatically move on to the next step. When all the stages are complete, the unit will sound an alarm and hold the last set temperature. The programmable stages can also be used to set a delayed start of up to 23 hours in advance so that you can have your water hot and ready to go when you get home from work or wake up in the morning. In order to do this, fill the unit with strike water and program the controller with two steps. Step 1 should be programmed at a temperature lower than the unheated strike water (so the elements will remain off), and the duration should be programmed for however long you want the delay. Then program Step 2 with your desired strike water temperature and a duration of 1-2 hours, giving the BrewZilla ample time to heat up and giving you a margin of error in case you hit the snooze button the morning of brew day. Recirculating Mash with Full Depth Malt Pipe The built-in magnetic drive pump easily recirculates wort during the mash. We recommend getting some silicone tubing to go with the recirculation arm. This allows you more control over the recirculation and you can then use the pump to transfer your wort to your fermenter. As with any mash, be sure to stir your grain very thoroughly after mashing-in so you start out with an even temperature throughout the grain bed. Some competing models advertise their perforated malt pipes as "high flow", but what they don't mention is how this affects efficiency. When recirculating the mash, wort will escape through the side perforations rather than passing through the grain at the bottom-most end of the malt pipe which can lead to lower efficiency. The BrewZilla's malt pipe is designed so that recirculating wort must pass through the entire grain bed before escaping through the false bottom and being pumped over the top of the grain bed again. If you're worried about the flow rate, simply add a pound or two of rice hulls to your grain bill. This is especially recommended when brewing with a high level of wheat, oat, or flaked grains. Power & Heating Control Dual heating elements run off of a single 110 volt plug and have individual switches allowing for more control over the heating process. One element is 1000 watts and the other is 500 for a combined 1500 watts! Use both when you need to ramp up the temperature quickly either at the start to get to your mash temp or to go from your mash temp to boiling. Use only one of the elements when you want to hold a temperature. We highly recommend adding the optional BrewZilla Neoprene Jacket to help reduce heating times and maintain a more vigorous boil. The extra thick neoprene jacket is custom designed to insulate the entire kettle portion of the BrewZilla while staying out of the way of the ball valve and handles. The jacket can help you acheive up to 10% faster heat up times and cut heat loss from the boiler in half. And when it comes time to cool your wort after the boil, simply remove the jacket! While other units boast a double wall design for better heat retention, this actually becomes a disadvantage when it comes to chilling. The digital control panel makes it easy to see the current temperature and set the temperature you want. The digital controller is also water resistant so don't worry about spills or some water dripping down the side. This controller is built for brewing! The brewery also includes a stainless steel malt pipe with false bottom allowing you to easily shift from mash tun to boil kettle during your brew day. The malt pipe includes a handle to lift it out and tabs at the base so you can set the malt pipe over the kettle to let the wort drain out. It also has feet at its base to raise the malt pipe slightly off the base and help prevent clogging. The included stainless steel wort chiller is shipped with bare ends so you can set it up for your situation. We list below the most common tubing and fittings to connect to a hose, hose bib, or faucet.   What MoreBeer! loves about this product: Homebrewing is trending in the direction of all-in-one, all-grain brewing systems and the BrewZilla is the ultimate value. The cost is half of the next comparable system with programmable mash steps and nearly the same as buying converted coolers and a kettle. We've brewed on all the systems and we can truly say the BrewZilla is the easiest to use. We feel confident that a lot of first time brewers could buy this and use it with ease. At the same time quite a few of our experienced, all-grain brewing staff are buying it to brew at home. The unit is extremely compact because the pump is built-in to the bottom of the unit. You can move it around with ease which makes it perfect for guys and gals that have space constraints. Someone on the team also mentioned how they like that you can drain it via gravity without having to use the pump. All in all a great buy and highly recommended. Please note you will need a few extra pieces of hardware to connect the wort chiller and at least 2' of silicone tubing for the sparge. Use the Pump for More Than Just Recirculation! One of the surprisingly handy features of the BrewZilla is that the recirculation pipe features a female camlock. This allows you to hook up other accessories and use the unit's pump for more than just recirculating wort. With a male camlock and silicone tubing, for example, you can use the internal pump to push wort through a plate chiller or counterflow chiller. Check out our selection of camlock fittings here.    Features: Gen 3.1.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons Digital temperature controller Automatic step mashing with 6 programmable stages 110V power and plug Dual heating elements for total control (1000 watts and 500 watts) Stainless steel 1/2 inch ball valve for draining (dont have to use the pump) Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Magnetic drive pump for recirculation Recirculation arm Bottom handle for easy lifting and pouring Upgraded rocker switches Rubber feet Temperature reads in °F or °C (press and hold temp button for several seconds to adjust) 32.75 in H (with recirculation arm) x 12.5 in D Recommended max. grain bill - 18 lbs Recommended min. grain bill - 8 lbs AlcoEngine Still ready with the purchase of a Distillation Lid You Will Need: 2' of H985 1/2" ID Silicone tubing for sparging and draining. To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950 hose clamps and (1) brass hose by thread adaptor (H508). These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout. Note: The manual references an element for a different market.  This unit comes with two heating elements for a total of 1,500 watts. Kegland Part Number: KL05838  

Read more less

The DigiBoil is a versatile electric kettle that can be used as a standalone unit or integrated into your current brew system to serve a variety of functions. Easily brew 5-gallon extract batches. Use it to preheat your strike water or sparge water to a precise temperature. Pair it with a pump and heat exchanger to use it for HERMS brewing. Or slap on a still top lid and condenser for distilling! With so many ways to use the DigiBoil, and an affordable price tag to boot, it's hard not to get excited about this electric kettle! The Gen 2 DigiBoil features an upgraded glass lid, allowing you to monitor your heated or boiling liquid. Interested in using the DigiBoil for all-grain brewing? With the Mash Upgrade Kit, you can easily convert the DigiBoil into an electric mash tun! This DigiBoil model has two built-in heating elements that run off a 110V plug. One element is 1000w and the other is 500w for a combined 1500 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage both elements to quickly go from steeping temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s).  Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach 1/2" FPT fittings if desired. Features: 304 stainless steel construction 9 gallon total capacity Digital temperature control 110V / 15A power and plug (5 ft. cord) Dual heating element control (1000w and 500w) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Glass lid Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Compatible with reflux and pot still (DS130 & DS120)* External Dimensions: 29" H x 15" W (including handles) Internal Dimensions: 19.5" H x 11.75" W ETL Listed *Distilling: to use the DigiBoil with a distilling condenser, you will need to purchase the still top lid and gasket (DS124). Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States.  It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA). KegLand Part Number: KL07245

Read more less

Updated With: 240V/120V Adapter Cable Water Deflecting Screen Improved Grain Basket with 1.5" Sidewall Perforations The ANVIL Foundry™ is the most versatile all-in-one brewing system available. From the triple element low watt density patented dual voltage heaters for blazing fast heating speeds, to the unique high flow grain basket, you won’t find a more powerful feature-rich product. Key Features: Patented Dual Voltage Switchable Between 120V 1600W, 13A and 240V 2800W, 12A for Faster Heating & Better Boils. (240V Standard) 240V/120V Adapter Cable - With this adapter you navigate to 240V for a faster brew day, or brew at the standard electric 120V by simply flipping the switch located on the back of the unit.The only all-in-one on that’s 240/120v Water Deflecting Screen - The improved screen mount feature has an added gasket with internal water deflecting geometry on the inside to ensure water doesn’t reach the screen.  Serviceable Touch Screen with 4x the Mounting Screws - Servicing the linear digital power control screen was a daunting process, now it’s as simple as removing 4 screws and pulling a single wire cable out of the screen.  After swapping the screen, you can plug the unit back in. Grain Basket Hosts 1.5” of Side Wall Perforations - They aren’t just back, they are improved!  The grain basket’s side wall perforations drastically reduce the amount of stuck mashes from happening. Large Capacity Increases Efficiency and Grain Capacity. Double Wall Insulation Maintains Mash Temps and Increases Heating Speeds. Ultra Low Watt Density, Triple Element Heaters - Won't Scorch. Linear Digital Power Control and Solid-State Switching for Fine Tuning your Boil. Turbo 500 Distillation Ready. Includes High Capacity Stainless Immersion Chiller with Hoses & Fittings. External Pump Won't Plug and is Easy to Clean. No Need to Disassemble Entire Unit! Use for Other Pumping Needs too. Three Sizes Available: 18 Gallon for 10 gallon batches, 10.5 Gallon for 5 Gallon Batches and 6.5 Gallon for 2.5-3 Gallon Batches. Specs: Max Grain Capacity - 16 lbs Tank Diameter = 12.5 inches Distance Across the Handles = 17 inches Height of Base Unit = 29.75 inches Lid = 3.25 inches Total Height = 33 inches Spigot Height from Base = 7 inches Shipping Weight = 38 lbs Wattage 120V = 1600 watts 240V = 2800 watts Caution! Do not CLAMP the lid in place while boiling. The steam buildup can lead to severe burns.  The lid should only be clamped when used for distillation. Read all instructions and practice safe brewing.

Read more less

The BrewBuilt SlingBlade is an innovative electric heating element designed to promote a rolling boil and even heat distribution. Shaped for Performance and Convenience The SlingBlade's unique crescent-shaped design positions all of the heating power on one side of the kettle, sending thermal energy upward to the surface that then cascades downward on the opposite side of the kettle. This movement creates a dynamic turbulence that evenly distributes heat while creating a vigorous, rolling boil. Other heating elements stick right out into the middle of the kettle or use a full circle design that rings the kettle wall. This can cause an obstruction for immersion chillers or make it difficult to stir without banging into the element. The SlingBlade was designed to avoid these issues. By remaining on one side of the kettle, the element will be out of the way of your immersion chiller, and since the element follows the curvature of the kettle wall, it won't interfere with the flow of wort during whirlpool. Ultra-Low Watt Density An electric element transfers power to your wort by applying heat, but if this heat is too concentrated you will get local heating that is hotter than 212°F. This catalyzes Maillard Reactions, which can lead to darker beer than intended and produce unwanted caramelization. Think of these reactions like roasting a marshmallow. First it gets a light brown, we call this Maillard reactions, a little hotter and it gets a dark brown, we call this caramelization, then it turns black and we call this pyrolysis (burnt or scorched). While all kettles undergo these reactions, an electric element can concentrate more heat into a small area, which can quickly scorch your wort. Our experience is that at 90-watts per square inch recipes need to be modified to account for the element and light beers never come out quite right. The SlingBlade element was designed at 50-watts per square inch to reduce the chance of scorching while still providing a vigorous boil. For even lower watt density, consider the Boil Vigor Controller. Tri-Clamp Connection The SlingBlade installs quickly and easily on any kettle with a T.C. ferrule thanks to the curved, non-circular design. This also makes it a breeze to remove the element for cleaning between uses. The SlingBlade heating elements were designed to fit perfectly with BrewBuilt brewing kettles, but you may find them suitable for other kettles as well. They should be used with T.C. ferrules no longer than 1" in length. For dimensions and recommended minimum kettle diameter, please see the chart below. Features: Made from Incoloy alloy with proprietary coating for long life 1.5" Tri-Clamp connection Unique offset design promotes rolling boil Ultra-Low Watt Density eliminates scorching UL Certified components Specs: 240 Volt L6-30 plug 20 Amp breaker required for 10 & 15 gal element 30 Amp breaker required for 22 & 31 gal element 50-gallon kettle requires 2 x BE538 and 2 x 30 amp circuits SKU Kettle Vol. Wattage Length Radius Min. Kettle Ø BE535 10 gal 3750 13.25" 6.3" 13.75" BE536 15 gal 4500 16.75" 7.3" 15.75" BE537 22 gal 5000 17.25" 8.3" 17.75" BE538 31 gal 5750 19.5" 9.3" 19.75" Please note: Length is measured from the tip of the heating element to the T.C. connection. Radius is measured from the middle of the T.C. connection to the outermost edge of the element's curve. ***In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.*** Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.

Read more less

A powerful, 304 stainless steel heating element well suited for most kettles. With its weldless design and a diameter of 1.25", it's easy to install. Simply drill a 1.25" hole in your kettle and tightening the nut from the outside. The heating element requires a power cord which can be purchased separately. Electrical connection requires a computer power connection IEC320 C13 to your 110 or 220 v plug). Available in either 1600 watt 110 volt or 2200 watt 220 volt. Features: Food grade, high temperature silicone seal The element itself is 11.5" long, 0.75" diameter Designed for use with 5 gallon batches Please Note - Having electrical devices around liquid can be hazardous, and should not be left unattended. Please use caution while using this device, and read the instruction manual prior to use. Use the 1.25" Hole Saw to drill a hole for this product.   Kegland Part number: KL03513

Read more less

The ANVIL Foundry™ is the most versatile all-in-one brewing system available. From the triple element low watt density dual voltage heaters for blazing fast heating speeds, to the unique high flow grain basket, you won't find a more powerful feature rich product.   These systems will ship free to anywhere in the contiguous United States.   Features: Switchable Between 120V 1600W and 240V 2800W for Faster Heating & Better Boils. Unique High Flow Grain Basket with 150% More Perforations to Virtually Eliminate Stuck Mashes. Large Capacity Increases Efficiency and Grain Capacity. Double Wall Insulation Maintains Mash Temps and Increases Heating Speeds. Ultra Low Watt Density, Triple Element Heaters - Won't Scorch. Linear Digital Power Control and Solid-State Switching for Fine Tuning your Boil. Turbo 500 Distillation Ready. Includes High Capacity Stainless Immersion Chiller with Hoses & Fittings. Optional External Pump Won't Plug and is Easy to Clean. No Need to Disassemble Entire Unit! Use for Other Pumping Needs too. Three Sizes Available: 18 Gallon for 10 gallon batches, 10.5 Gallon for 5 Gallon Batches and 6.5 Gallon for 2.5-3 Gallon Batches.   Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less. Caution! Do not CLAMP the lid in place while boiling. The steam buildup can lead to severe burns.  The lid should only be clamped when used for distillation. Read all instructions and practice safe brewing.

Read more less

Elevate your brewing game with the 220V 17 Gallon Gen 4 BrewZilla. This cutting-edge system combines more power & capcity with innovative features like wireless connectivity via WiFi & Bluetooth, allowing you to heat faster while you control and monitor your brew day, ensuring precision, convenience, and exceptional beer batch after batch!   WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 41.5 lb capacity, the BrewZilla can mash nearly 20% more grain than similar sized models of the Anvil Foundry and Grainfather G70. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 17.1 gallon total capacity with a finished beer output of 10-12 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 220-240V power NEMA 6-30P plug Requires NEMA 6-30R receptacle Requires 16 amps from 30 amp circuit Triple heating elements (2000, 1000 and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 36" H (with recirculation arm) x 16" D Recommended max. grain bill: 41.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Flow: 5 gal/min Max Head: 11 ft. Voltage: 220–240V-AC Frequency: 50–60Hz Power: 25 watts Fittings: 1/2" (13 mm) barbs You Will Need: 2' of H985 1/2" ID Silicone tubing for sparging and draining. To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950 hose clamps and (1) brass hose by thread adaptor (H508). These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout. KegLand Part Number: KL27458 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.   35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge    

Read more less

The Gen 2 DigiBoil features two distinct updates that are not currently pictured in the primary images. The stainless steel lid has been upgraded to a glass lid, allowing you to observe and monitor boil activity. The rubber feet have been replaced with a plastic base that provides improved stability and slightly raises the unit for better ground clearance. Updated images coming soon. The most affordable all-in-one automated all-grain brewing system! Mash grains and boil wort in a single vessel DigiBoil electric kettle automatically maintains mash temperatures with the digital controller Dual heating elements combine for 1500W of power Also available with optional Recirculation Pump Kit! The DigiMash system represents the best value in electric all-grain brewing you'll find. With a 9-gallon DigiBoil electric kettle and the DigiMash stainless steel mashing accessory pack included, this is by far the most affordable way to get into electric all-grain brewing.  It may not have all the bells and whistles of the BrewZilla, but it does have everything you need to mash and boil all in one unit. Setting up and using the DigiMash couldn't be easier. Simply place the false bottom inside the kettle and install the malt pipe, fill with water and heat to your desired strike temperature, then add your grain and set your desired mash temperature on the digital controller. Once your mash is complete, lift up the malt pipe, drain the wort and sparge, then remove the malt pipe and proceed to boil. If you're deciding between the DigiMash and the BrewZilla, there are a couple of key differences worth noting. One of our favorite features of the BrewZilla is the programmable mash steps and delayed start, which the DigiMash does not have. You can still step mash by simply raising the temperature manually on the controller, but the automatic steps are a convenient feature if you want to set it and forget it. The other major difference between the two systems is that the BrewZilla features a built-in pump for recirculating the mash. Recirculation is a great way to improve mash efficiency, but it is far from required for a successful brew day. Using an external pump with the DigiMash is also an option, and one can be integrated for mash recirculation quite easily. Simply connect the ball valve to the inlet of your pump, and then connect the outlet of the pump to our Sparge Arm Assembly. This model comes with the 35L DigiBoil, which has two built-in heating elements that run off a 110V plug. One element is 1000w and the other is 500w for a combined 1500 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage both elements to quickly go from mash temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s).  Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach fittings with 1/2" FPT, such as our female threaded quick disconnect. DigiBoil Features: 304 stainless steel construction 9 gallon total capacity Digital temperature control 110V / 15A power and plug (5 ft. cord) Dual heating element control (1000w and 500w) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Stainless lid Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Recommended max. grain bill - 18 lbs Recommended min. grain bill - 8 lbs External Dimensions: 29" H x 15" W (including handles) Internal Dimensions: 19.5" H x 11.75" W ETL Listed DigiMash Stainless Steel Accessory Pack Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen    

Read more less

Elevate your brewing game with the 220V Gen 4 BrewZilla. This cutting-edge system combines more power with innovative features like wireless connectivity via WiFi & Bluetooth, allowing you to heat faster while you control and monitor your brew day, ensuring precision, convenience, and exceptional beer batch after batch! WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 220-240V power NEMA 6-30P plug Requires NEMA 6-30R receptacle Requires 11 amps from 30 amp circuit Dual heating elements (1900 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 220–240V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 You Will Need: 2' of H985 1/2" ID Silicone tubing for sparging and draining. To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950 hose clamps and (1) brass hose by thread adaptor (H508). These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout. KegLand Part Number: KL27434 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning:  Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.   35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge    

Read more less

Ready to upgrade your DigiBoil into a DigiMash? With the DigiMash upgrade kit you can convert the DigiBoil into a full blown electric all-in-one system. Includes false bottom, malt pipe with bottom screen, wire support, and malt pipe handle. Simply place the false bottom inside the kettle and install the malt pipe, fill with water and heat to your desired strike temperature, then add your grain and set your desired mash temperture on the digital controller. Once your mash is complete, lift up the malt pipe, drain the wort and sparge, then remove the malt pipe and proceed to boil. Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen Installation & Use: Place the false bottom inside the kettle Install the wire support in the channel located at the top of the kettle Place the mesh screen inside the malt pipe and attach the handle Lower the malt pipe into the kettle so it rests on the wire support Fill with strike water and heat to desired strike temperature When desired temperature is reached, add grain and stir until well mixed When your mash is complete, use the handle to lift out malt pipe and rotate 90° so the malt pipe feet sit on the wire support Allow the wort to drain into the kettle and sparge the grain with warm water (165-175°F) When you're done collecting your wort, remove the malt pipe and proceed to boil   Please note: only the 500-watt element should be used to increase mash temperatures when the Malt Pipe is in place. Using the higher watt element(s) with the Malt Pipe inserted may cause scorching of the grain.   Kegland Part Number: KL13055

Read more less

The Gen 2 DigiBoil features two distinct updates that are not currently pictured in the primary images. The stainless steel lid has been upgraded to a glass lid, allowing you to observe and monitor boil activity. The rubber feet have been replaced with a plastic base that provides improved stability and slightly raises the unit for better ground clearance. Updated images coming soon. The most affordable all-in-one automated all-grain brewing system! Mash grains and boil wort in a single vessel DigiBoil electric kettle automatically maintains mash temperatures with the digital controller Dual heating elements combine for 2400W of power Also available with optional Recirculation Pump Kit! The DigiMash system represents the best value in electric all-grain brewing you'll find. With a 9-gallon DigiBoil electric kettle and the DigiMash stainless steel mashing accessory pack included, this is by far the most affordable way to get into electric all-grain brewing. It may not have all the bells and whistles of the BrewZilla, but it does have everything you need to mash and boil all in one unit. Setting up and using the DigiMash couldn't be easier. Simply place the false bottom inside the kettle and install the malt pipe, fill with water and heat to your desired strike temperature, then add your grain and set your desired mash temperature on the digital controller. Once your mash is complete, lift up the malt pipe, drain the wort and sparge, then remove the malt pipe and proceed to boil. If you're deciding between the DigiMash and the BrewZilla, there are a couple of key differences worth noting. One of our favorite features of the BrewZilla is the programmable mash steps and delayed start, which the DigiMash does not have. You can still step mash by simply raising the temperature manually on the controller, but the automatic steps are a convenient feature if you want to set it and forget it. The other major difference between the two systems is that the BrewZilla features a built-in pump for recirculating the mash. Recirculation is a great way to improve mash efficiency, but it is far from required for a successful brew day. Using an external pump with the DigiMash is also an option, and one can be integrated for mash recirculation quite easily. Simply connect the ball valve to the inlet of your pump, and then connect the outlet of the pump to our Sparge Arm Assembly. This model comes with the 35L DigiBoil, which has two built-in heating elements that run off a 220V plug. One element is 1900w and the other is 500w for a combined 2400 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage both elements to quickly go from mash temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s). If you have access to 220V power, this is definitely the unit we recommend. Although 110V power is enough to get up to boil, 220V will get you there faster and provide a much more vigorous boil. Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach fittings with 1/2" FPT, such as our female threaded quick disconnect. DigiBoil Features: 304 stainless steel construction 9 gallon total capacity Digital temperature control 220V / 15A power  NEMA 6-30R plug (5 ft. cord) Dual heating element control (1000w and 500w) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Stainless lid Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Recommended max. grain bill - 18 lbs Recommended min. grain bill - 8 lbs External Dimensions: 29" H x 15" W (including handles) Internal Dimensions: 19.5" H x 11.75" W ETL Listed DigiMash Upgrade Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen    

Read more less

Anvil Foundry Recirculation Pump Kit for 6.5 / 10.5 gal units.   Features: Anvil Recirculation Pump 4 ft. of Silicone Hose 4 Hose Clamps Flow Clamp Stainless Return Tube Perforated Disc Eye Bolt & Nuts for Eye Bolt

Read more less

Elevate your brewing game with the Gen 4 BrewZilla. This cutting-edge system combines innovative features like wireless connectivity via WiFi & Bluetooth, allowing you to control and monitor your brew day, ensuring precision, convenience, and exceptional beer batch after batch! WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 110-120V power and plug 12.5A Requires 20A circuit Dual heating elements (1000 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 110–120V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 You Will Need: 2' of H985 1/2" ID Silicone tubing for sparging and draining. To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950 hose clamps and (1) brass hose by thread adaptor (H508). These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout. KegLand Part Number: KL32766 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning:  Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.   35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge

Read more less

Ripple-style electric brewing heating element with 1.5" tri-clamp connection. With 5,500 watts of power, this unit will easily heat 20+ gallons of wort. Measures 4" wide and 14.5" from TC connection to tip of element. Specs: 5,500 watts 240 Volt L6-30 plug 30 Amp breaker required In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.    

Read more less

The Gen 2 DigiBoil features two distinct updates that are not currently pictured in the primary images. The stainless steel lid has been upgraded to a glass lid, allowing you to observe and monitor boil activity. The rubber feet have been replaced with a plastic base that provides improved stability and slightly raises the unit for better ground clearance. Updated images coming soon. The most affordable all-in-one automated all-grain brewing system! Mash grains and boil wort in a single vessel DigiBoil electric kettle automatically maintains mash temperatures with the digital controller Triple heating elements combine for 3500W of power Also available with optional Recirculation Pump Kit! The DigiMash system represents the best value in electric all-grain brewing you'll find. With a 17-gallon DigiBoil electric kettle and the DigiMash stainless steel mashing accessory pack included, this is by far the most affordable way to get into electric all-grain brewing at the 10-gallon batch level. It may not have all the bells and whistles of the BrewZilla, but it does have everything you need to mash and boil all in one unit. Setting up and using the DigiMash couldn't be easier. Simply place the false bottom inside the kettle and install the malt pipe, fill with water and heat to your desired strike temperature, then add your grain and set your desired mash temperature on the digital controller. Once your mash is complete, lift up the malt pipe, drain the wort and sparge, then remove the malt pipe and proceed to boil. If you're deciding between the DigiMash and the BrewZilla, there are a couple of key differences worth noting. One of our favorite features of the BrewZilla is the programmable mash steps and delayed start, which the DigiMash does not have. You can still step mash by simply raising the temperature manually on the controller, but the automatic steps are a convenient feature if you want to set it and forget it. The other major difference between the two systems is that the BrewZilla features a built-in pump for recirculating the mash. Recirculation is a great way to improve mash efficiency, but it is far from required for a successful brew day. Using an external pump with the DigiMash is also an option, and one can be integrated for mash recirculation quite easily. Simply connect the ball valve to the inlet of your pump, and then connect the outlet of the pump to our Sparge Arm Assembly. This model comes with the 65L DigiBoil, which has three built-in heating elements that run off a 220V plug. The elements are 2000w, 1000w and 500w for a combined 3500 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage all three elements to quickly go from steeping temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s). Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach fittings with 1/2" FPT, such as our female threaded quick disconnect. DigiBoil Features: 304 stainless steel construction 17 gallon total capacity Digital temperature control 220V / 20A power NEMA 6-30R plug (4.5 ft. cord) Triple heating element control (2000w, 1000w and 500w) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Glass lid Temperature reads in °F or °C With elements turned off, hold both the +/- buttons to switch between °F or °C External Dimensions: 29" H x 19.5" W (including handles) Internal Dimensions: 20.25" H x 15.75" W ETL Listed DigiMash Upgrade Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen NOTE: Due to the size of this item, it is not eligible for international shipping.  

Read more less

Ready to upgrade your DigiBoil into a DigiMash? With the DigiMash upgrade kit you can convert the DigiBoil into a full blown electric all-in-one system. Includes false bottom, malt pipe with bottom screen, wire support, and malt pipe handle. Simply place the false bottom inside the kettle and install the malt pipe, fill with water and heat to your desired strike temperature, then add your grain and set your desired mash temperature on the digital controller. Once your mash is complete, lift up the malt pipe, drain the wort and sparge, then remove the malt pipe and proceed to boil. The Gen 2 DigiMash Upgrade Kit is backwards compatible with Gen 1 DigiBoils. Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen Installation & Use: Place the false bottom inside the kettle Install the wire support in the channel located at the top of the kettle Place the mesh screen inside the malt pipe and attach the handle Lower the malt pipe into the kettle so it rests on the wire support Fill with strike water and heat to desired strike temperature When desired temperature is reached, add grain and stir until well mixed When your mash is complete, use the handle to lift out malt pipe and rotate 90° so the malt pipe feet sit on the wire support Allow the wort to drain into the kettle and sparge the grain with warm water (165-175°F) When you're done collecting your wort, remove the malt pipe and proceed to boil Please note: only the 500-watt element should be used to increase mash temperatures when the Malt Pipe is in place. Using the higher watt element(s) with the Malt Pipe inserted may cause scorching of the grain. Kegland Part Number: KL12980

Read more less

The easiest way to power the BrewBuilt™ SlingBlade! This professionally wired watertight switch gives you a simple On/Off control of your heating element. Switches both legs of a 220V 30AMP circuit and comes with 5 ft. input and output cords with molded LP6-30P ends. It also features two handy tabs for mounting to a wall. Don't wear out your expensive plugs and sockets hot patching your 220V burner elements. Plugging your element directly into a live power outlet will cause a small spark, and when done repeatedly this can damage the plug and the socket, especially with high voltage 220V appliances. Not only is the power switch more convenient to turn your element on and off during the brew day, it will eliminate the risk of damage done by hot patching.  

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.   304 stainless steel splash resistant construction Industrial design using commericial quality components for long life and easy serviceability Digital power reading for precise repeatability. No more guessing if you found the sweet spot on the dial Outlet fully disconnected when powered off for added safety, unlike some one-leg designs Linear power control for better repeatability at low power settings Wall mount bracket allows you to get the controller off the table and out of the way Dial your brew day up to 11 with the BrewBuilt™ Boil Vigor Controller! This controller allows you to control the current of a 208-240V heating element up to 30 amps. Perfect for dialing in your boil vigor for more consistent boil-off rates or adjusting the heat input to a still wash pot. The controller works by adjusting the percentage of power delivered to the heating element. The power is increased in a linear fashion from 0 to 100% as you adjust the dial from 1 to 11. Features industrial-style power switch, dial knob, and digital amm meter mounted on a splash resistant stainless steel enclosure. Pre-cut mounting holes allow you to hang the controller on your brew stand on the wall at eye-level. We highly recommend mounting the controller so you don't have to worry about keeping an area of your table dry where you might lay it down. L6-30 connections with 4 ft. cords on either end. Compatible with all 208-240V elements 30 amps and lower. While L6-30 are the most common elements available, yours may need an adapter. The Boil Vigor Controller uses a generously overrated SSR with a very large fan-cooled heatsink for better reliability. An SSR's life expectancy is directly related to its operating temperature, and this unit is built with the lowest Q heat dissipation system offered at the homebrewing level. It includes a contactor to fully shut off both legs when you throw the power switch, making the free end of the cord safer when the element is not plugged in. The display gives you a reading of the actual current being consumed by your element in Amps. On some systems, a small change in the adjustment makes a large current change at the element, especially at lower settings used during hop stands and distillation. The BrewBuilt controller provides a linear control and a digital readout to eliminate the guessing, allowing you to focus on your process and not your equipment. If you'd prefer not to mount the controller to your wall, consider the stainless steel Controller Stand.   **Caution: In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.**  

Read more less

Perfect for powering 230V / 30 amp electric elements, power controllers and brewing systems away from your main wall socket. Comes with male and female L6-30 sockets on either end. 10 feet long.

Read more less

304 stainless steel splash resistant construction Industrial design using commercial quality components for long life and easy serviceability On/Off thermostat control Outlet fully disconnected when powered off for added safety, unlike some one-leg designs Wall mount bracket allows you to get the controller off the table and out of the way Keep your temps tight with the BrewBuilt™ HLT Controller! Perfect for keeping your sparge water or mash water at your set temperature—it allows you to control a 208-240V heating element up to 30 amps based on temperature. The controller works by turning the burner power on and off at 100% power until it reaches the temperature setpoint. Features industrial-style power switches, and a 1/6 DIN Controller mounted on a splash resistant stainless steel enclosure. Pre-cut mounting holes allow you to hang the controller on your brew stand on the wall at eye-level. We highly recommend mounting the controller so you don't have to worry about keeping an area of your table dry where you might lay it down. L6-30 connections with 4 ft. cords on either end. Compatible with all 208-240V elements 30 amps and lower. While L6-30 are the most common elements available, yours may need an adapter. Uses a 9' stainless braided PT-100 temperature sensor. The HLT Controller includes a contactor to fully shut off both legs when you throw the power switch, making the free end of the cord safer when the element is not plugged in. If you'd prefer not to mount the controller to your wall, consider the stainless steel Controller Stand.   **Caution: In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.**    

Read more less

The ANVIL Foundry™ is the most versatile all-in-one brewing system available. From the triple element low watt density dual voltage heaters for blazing fast heating speeds, to the unique high flow grain basket, you won't find a more powerful feature rich product. These systems will ship free to anywhere in the contiguous United States. Key Features: 240V Operation 6-20P plug 4000W 17A for Faster Heating & Better Boils. Cleaning is a breeze with the Patented Removable False bottom. Grain Capacity - 36 Pounds Double Wall Insulation Maintains Mash Temps and Increases Heating Speeds. Linear Digital Power Control and Solid-State Switching for Fine-Tuning your Boil. Turbo 500 Distillation Ready. Includes High Capacity Stainless Immersion Chiller with Hoses & Fittings. External Pump Won't Plug and is Easy to Clean. No Need to Disassemble Entire Unit! Use for Other Pumping Needs too. Three Sizes Available: 18 Gallon for 10 gallon batches, 10.5 Gallon for 5 Gallon Batches and 6.5 Gallon for 2.5-3 Gallon Batches. Minimum batch size: 5 gallons Optional Recirculation Pump Kit Optional Swirly™ Whirlpool Wattage - 6-20P 240V = 4000 watts Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.   Caution! Do not CLAMP the lid in place while boiling. The steam buildup can lead to severe burns.  The lid should only be clamped when used for distillation. Read all instructions and practice safe brewing.  

Read more less

The DigiBoil is a versatile electric kettle that can be used as a standalone unit or integrated into your current brew system to serve a variety of functions. Easily brew 5-gallon extract batches. Use it to preheat your strike water or sparge water to a precise temperature. Pair it with a pump and heat exchanger to use it for HERMS brewing. Or slap on a still top lid and condenser for distilling! With so many ways to use the DigiBoil, and an affordable price tag to boot, it's hard not to get excited about this electric kettle! The Gen 2 DigiBoil features an upgraded glass lid, allowing you to monitor your heated or boiling liquid. Interested in using the DigiBoil for all-grain brewing? With the Mash Upgrade Kit, you can easily convert the DigiBoil into an electric mash tun! This DigiBoil model has two built-in heating elements that run off a 220V plug. One element is 1900w and the other is 500w for a combined 2400 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage both elements to quickly go from steeping temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s). If you have access to 220V power, this is definitely the unit we recommend. Although 110V power is enough to get up to boil, 220V will get you there faster and provide a much more vigorous boil. Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach 1/2" FPT fittings if desired. Features: 304 stainless steel construction 9 gallon total capacity Digital temperature control 220V / 15A power NEMA 6-30 plug (5 ft. cord) Dual heating element control (1900w and 500w) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Glass lid Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Compatible with reflux and pot still (DS130 & DS120)* External Dimensions: 29" H x 15" W (including handles) Internal Dimensions: 19.5" H x 11.75" W ETL Listed *Distilling: to use the DigiBoil with a distilling condenser, you will need to purchase the Distillation Lid. Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States.  It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA). KegLand Part Number: KL07252

Read more less

Preheat your mash before beginning the brewing process with this 1000W Electric Bucket Heater. This handy little tool works in conjunction with a product like the Ranco or Johnson temperature controller by enabling you to set an exact hot liquid temperature on the controller, and then attaching it to the bucket heater. The temperature controller will turn off the bucket heater once it reaches your desired temperature. Our bucket water heater is designed to use with water in a bucket or cooler where an open flame cannot be used, and you can even use it to heat a bucket of water for cleaning with a powdered brewery wash. This water bucket heater measures 17 inches from the handle to the tip and comes with a 6-foot long cord. It requires at least 6 inches of water for full submersion, and it can only be used with a maximum depth of 14 inches.  Unit has stainless steal heating element and guard.  Does not include clip for mounting.  Please Note - Having electrical devices around liquid can be hazardous, and should not be left unattended. Please use caution while using this device, and read the instruction manual prior to use.

Read more less

Used on a commercial brewing system to shut off electricty or gas before the kettle runs dry.  This horizontal float switch conveniently fits into a 1.5" tri-clamp port. It is designed to control the run-dry circuit in an electric brewing system. The contacts are intended to control a relay, contactor, or SSR and should not be used to interrupt full power to an electric element/burner. 50W. The unit is not fit to use on a circuit load, but suitable for signal output.  

Read more less

PLEASE NOTE: The supplier of this product has temporarily halted shipments to addresses within the state of California. If you are a CA resident, please note your order will not be fulfilled and will ultimately be canceled. We hope to have this issue resolved with the supplier as soon as possible.   Large 11 gallon preboil capacity Powerful 3,300 watt heating element Color LCD controller magnetically mounted for easy removal and cleaning Wireless control via the Grainfather Community App Dual stage false bottom to prevent stuck sparges Wort chiller included The Grainfather G40 brewing system has a bigger capacity and better connectivity. Produce up to 40L (11 US Gal) of beer from one brew and connect your mobile device to the smart controller with built-in wireless control via the Grainfather App, for step-by-step brewing and access to bazillions of recipes. The Grainfather G40 is the latest brewing system in the G Series range from Grainfather. Packed with all of the innovative features you can find in the G70, this brewing system is your new best friend for brews up to 11 gal (40L), perfect to fill two 5 gal corny kegs. With a max grain bill of 29 lb., you can choose to add extra grain and less liquid to make beer with an ABV over 9%.   Manage your brew remotely with step-by-step brewing with the smart wireless controller. All you need to do is connect your mobile device to the controller and control your brew through the FREE Grainfather app where you have access to bazillions of recipes to choose from, or create your own!   Please Note - this system comes standard with a NEMA 6-15P plug, and requires access to a 220v-240v power supply.   Features: G40 body built with sleek 304-grade stainless steel Large, surface mounted heated elements heat wort evenly Connect your mobile device to the smart wireless controller via the Grainfather App (link to the Grainfather app page) and manage your brew remotely. The Grainfather app gives you access to brewing tools and calculators to brew with confidence, and bazillions of recipes to choose from or create your own. Reach your expected gravity with a conical base for maximum wort transfer Comes with a counterflow wort chiller for a more efficient and sanitary brew transfer PID heating control for accurate temperature management during mashing Quick and easy cleaning with CIP (clean in place) capability An integrated sight glass for easy volume reading Rolled edge mash plate and large hop filter to reduce blockages What's Included: Grainfather G40 Smart controller with built-in wireless connectivity Counterflow wort chiller Glass lid Lifting bar Inner basket Recirculation hose Grain plate Hop filter Fittings Specs: Size: 26" x 21" Weight: 64lb Capacity: 12 gal Batch volume Maximum: 11 gal (40L) Minimum: 3 gal (10L) Grain bill Maximum: 29 lb (13kg)* Minimum: 7 lb (3kg) *Max weight depends on grain crush, type, and variety. Large grain bills may also require the use of an additional grain plate." Power: 3300W, 240V Connectivity: Wireless control  

Read more less

Digital temperature control Triple heating element control (2000w, 1000w and 500w) 17 gallon total capacity 304 stainless steel construction 220V / 20A power This is a versatile electric kettle that can be used as a standalone unit or integrated into your current brew system to serve a variety of functions. Easily brew 10-gallon extract batches. Use it to preheat your strike water or sparge water to a precise temperature. Pair it with a pump and heat exchanger to use it for HERMS brewing. Or slap on a still top lid and condenser for distilling! With so many ways to use the DigiBoil, and an affordable price tag to boot, it's hard not to get excited about this electric kettle! The Gen 2 DigiBoil features an upgraded glass lid, allowing you to monitor your heated or boiling liquid. Interested in using the DigiBoil for all-grain brewing? With the Mash Upgrade Kit, you can easily convert the DigiBoil into an electric mash tun! This DigiBoil model has three built-in heating elements that run off a 220V plug. The elements are 2000w, 1000w and 500w for a combined 3500 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage all three elements to quickly go from steeping temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s).  Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach 1/2" FPT fittings if desired. More! Features: NEMA 6-30R plug (4.5 ft. cord) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Glass lid Temperature reads in °F or °C With elements turned off, hold both the +/- buttons to switch between °F or °C Compatible with reflux and pot still (DS130 & DS120)* External Dimensions: 29" H x 19.5" W (including handles) Internal Dimensions: 20.25" H x 15.75" W ETL Listed *Distilling: to use the DigiBoil with a distilling condenser, you will need to purchase the still top lid (DS127). Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States.  It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. MoreBeer! is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA).   Kegland Part number: KL07313 NOTE: Due to the size of this item, it is not eligible for international shipping.    

Read more less

This 21" whirlpool works perfectly with the 10.5 Gallon Foundry™, brew kettles, and any other brewing system. The rotating rubber piece allows it to secure to the side of any vessel, no matter the thickness. The Swirly™ uses a 1/2" Straight Pipe Thread for hose connections and includes a hose barb for connecting your water supply. Patent pending.   The 21" Swirly fits any vessel that is 15"-27" in container height.

Read more less

PLEASE NOTE: The supplier of this product has temporarily halted shipments to addresses within the state of California. If you are a CA resident, please note your order will not be fulfilled and will ultimately be canceled. We hope to have this issue resolved with the supplier as soon as possible.   Compact and simple to use, with a small footprint for brewing indoors the Grainfather G30³ provides a home brewery system that with superior design, innovative features and the latest technology, allows you to brew professional quality craft beer at home. The Grainfather, is your all in one brewing system, to make beer from grain. The sleek look, user friendly, intuitive design, and innovative features, make this your perfect brewing companion for both experienced and beginner all grain brewers. It is made from high quality 304 grade stainless steel with a 8 Gal capacity, designed to make up to 6 Gal of beer from one brew. New Features: 1.) Auto Reset Switch Lifting and reaching underneath the boiler to reset your electric homebrewing system is now a thing of the past! The new auto reset switch avoids needing a physical, manual switch to reset the system; ensuring homebrewers can quickly and easily resume their brew day if an unexpected reset is required. 2.) Grain Basket Assembly The newly redesigned Perforated Edge Grain Basket on the G30³ features side wall perforations to improve wort flow and to prevent a stuck mash. In addition to the redesigned grain basket, the new Rolled Edge Mash Plate filters the wort efficiently without warping. The new rolled edges mean that there is no need for silicone seals, making the plates much easier to install, remove, and clean. The new grain basket and mash plate design means that there is no need for overflow pipework or a top plate, allowing for a hassle-free brew day. Same Great Features: Benefits of Electric Heating The Grainfather is electrically powered and designed to be used indoors. No need for burners, or hot plates, just plug in and go! It is fitted with a controlled heating element so that the correct power can be used depending on what stage of the brewing process you are at. A gentler heat is used at certain stages for accurate temperature control and to minimize the risk of scorching and after the mash it can also ramp up the heat quickly for when more vigorous heating is required. Heating from mash to boil takes as little as 20 minutes. Wireless Control for Heat, Power, and Pumping Use the Grainfather G30³ Control Box in conjunction with the Connect App and Grainfather Brewing Community for the ultimate brewing experience. Create your recipes on the Grainfather Brewing Community and then sync these recipes with the Connect app. The control box has Bluetooth connection to your mobile device so it can be controlled remotely. This allows you to multitask or simply relax while brewing and then be alerted when to return to your next step.  Features: PID algorithm works in conjunction with a TRIAC for more stable heating and so you can control power output Programmable step mashing Delayed heating - fill your Grainfather with water the night before and wake up to your water at strike temperature ready for brewing straight away Change between Celsius and Fahrenheit easily Waterproof graphic display Use in manual mode or with app Grainfather App: Ability to import recipes (Beer XML files) - NOTE: iOS9 and higher Set your own boil temperature (for different altitudes) Change between Celsius and Fahrenheit easily Grainfather calculators provided in app Create recipes on the Grainfather Brewing Community and then sync these with the Connect App to brew Powerful Magnetic Drive Pump A 6 Watt, 1,800 RPM magnetic powered pump has been fitted to recirculate the wort through the grain bed for maximum brewing efficiencies. This can also be used during the cooling stage to pump hot wort through the optional Counter Flow Wort Chiller. The pump also makes the cleaning process quick and easy by pumping the cleaning detergent through all the pipe work. The magnetic drive pump has been selected after rigorous testing of multiple pump styles to ensure it meets the tough demands required of continuous brewing. The pump is concealed by a stainless pump cover, which is easy to pop open, giving you direct access. A pump filter is fitted inside the Grainfather to prevent hops and stray grain from entering the pump or pipework, keeping the wort clear while also preventing any blockages.  Specifications: 304 Grade stainless steel body 110 - 120V 8 Gal Capacity Expandable grain basket to suit grain bills up to 20 lb A robust magnetic drive pump (6 watt, 1800 RPM) Tempered glass lid for maximum durability, heating efficiencies and visibility during your brew day    

Read more less

Elevate your brewing game with the 220V 26 Gallon Gen 4 BrewZilla. This cutting-edge system combines more power & capcity with innovative features like wireless connectivity via WiFi & Bluetooth, allowing you to heat faster while you control and monitor your brew day, ensuring precision, convenience, and exceptional beer batch after batch!   WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Heat Exchanger Dish The 100L BrewZilla comes standard with the Heat Exchanger Dish which redirects the flow of wort so that it spends more time exposed to the heating elements before reaching the center drain at the bottom of the kettle and being recirculated. Due to the concave bottom and central draining hole on the Gen 4 BrewZilla, recirculating wort will pass through the malt pipe and then down through the boiler false bottom following the path of least resistance. This can cause wort to make a B-line for the drainage hole and reduce the wort's exposure to the unit's heating elements. With the HED installed, wort will be directed to the edge of the BrewZilla base and pass over the elements for a longer period and reduce the time needed to heat to your set temperature. An optional accessory for the smaller units, but included as standard on the 100L BrewZilla. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Features: Gen 4.1 Stainless steel construction 26.4 gallon total capacity with a finished beer output of 15-20 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 220-240V power NEMA L6-30P Plug Requires NEMA L6-30R receptacle Draws 30 amps. Ask your electrician if you need to oversize the circuit (3) 2,200W heating elements Stainless steel 1/2" ball valve for gravity draining or transferring via pump Heat exchanger dish included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 36" H (with recirculation arm) x 20.5" D (boiler only) Recommended max. grain bill: 41.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 5 gal/min Max Head: 11.15 ft. Voltage: 220–240V-AC Frequency: 50–60Hz Power: 25 watts Input/Output: 13mm barb You Will Need: 2' of H985 1/2" ID Silicone tubing for sparging and draining. Wort Chiller for cooling We recommend either of the below counterflow chillers Copper Counterflow Chiller (WC130) BrewBuilt® Stainless Tri-Clamp Counterflow Chiller (WC140)   KegLand Part Number: KL32803 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning:  Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.   35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge    

Read more less

The B150pro – the largest Brewtools pro-series system, is a brewing system without compromise. Built for enthusiasts, nano breweries and brewpubs. 170-liter (44 gal) tank volume and 35kg (77 lb) malt capacity 6.6kW heating power (2x3.3kW) utilizing two mains inputs High accuracy with 2 digital sensors Conical bottom with center draining for fast and easy cleaning Powerful control system with 7" touch-screen, Wifi and Bluetooth 4.2 The B150pro has an 150 liter (40 gal) boil capacity and about 35 kg (77 lb) malt capacity. It is equipped with a powerful pump, which can be controlled from the touch-screen. The wort is circulated up through the center-pipe and the pump is fitted using Tri-Clamps making it very easy to remove, even when the tank is full. The malt pipe has latches that folds out when you hoist it to secure it for draining. To lift the malt pipe on this system you require a lifting system. This is being developed with a custom brewing table and will be ready in the near future. Sparging is done without tubes or pipes outside the tank. A sparge tube installed on the outside of the centerpipe follows the malt pipe when lifted also lifting the wort spreading device. This makes it very easy to sparge from a separate tank without making a mess. After brewing with the B150pro, cleaning is fast and easy. The centerpipe is removed easily, and you can easily clean the unit, and all the trub will be drained directly to a bucket or the drains. Use the included circulation device as a CIP solution to save time and cleaning chemicals. The system has two digital temperature sensors - one in the bottom of the tank and one before the pump. The maxium static offset is ±0,5°C. The sensors can be individually calibrated for maximum accuracy. They have an accuracy of 0.1°C. It's also possible to connect a third sensor (accessory) to monitor the temperature of the wort returning from the counterflow cooler, so you can pump directly to the fermenter when the temperature is right. All ports are 34mm Tri-Clamp fittings for maximum flexibility without leaks. As standard the system is shipped with one 3-way valve. All silicone tubes are 16x25mm food grade silicone. The control system is custom developed and features high quality electronics. The software is constantly being improved with new features. It is updated via WiFi. Note that with the added capacity of this system, heating to strike temperature and boiling will take more time compared to our other Pro systems. Specifications: Dimensions excl. packaging: 31.1" H x 28.3" W x 28.3" D Dimensions with one side valve: 31.1" H x 32.2 W x 28.3" D Dimensions with two valves: 31.1" H x 36.2 W x 28.3" D Packaging dimensions: 38.1" H x 28.3" W x 28.3" D Weight excl. packaging: 83 lbs Weight incl. packaging: 99 lbs Tank dimensions: Ø23.6", height 23.6" Tank volume: 44.6 gal (rec maximum boil volume – 39.6 gal) Malt pipe dimensions: Ø19.6", height 21.6" Malt pipe volume: 28.5 gal Max recommended grain quantity: 77 lbs Minimum liquid volume: 9.2 gal Build material: 1.0/1.2 mm stainless steel (SS304) Heating elements: 230V, 6600W (2x3300W) (two individual circuits) Pump: 24VDC brushless, max 6.6 gal/min, max head 14.7 ft, stainless steel head, stepless speed control from touch display Controller: ARM Cortex M4 180mhz, 7" Touch display Connectivity: WiFi 802.11 b/g/n, Bluetooth 4.2, MicroSD Hoses: 16x25mm silicone, food grade What's included: Complete brewing system with controller, pump, tank sensor, heaters and lid Malt pipe with handle and latches 1 pcs expanded metal filter 1 pcs 3-way valve Temperature sensor with adapter for pump line 5 pcs 34mm Tri Clamps with gaskets (all used for standard setup) 3 pcs 34mm TC blind caps 1 pcs dip tube, short type 1 pcs mash hat for spreading the wort 1 pcs sparge tube 150cm 16x25mm silicone tube 1 pcs 34mm TC to 19mm hose barb adapter O-rings for the center pipe and dip tube 2 Nema 6-20 power cables, 2 meter 5 year manufacturer's warranty Please note that some parts of Brewtools systems are made by hand, and might have some minor cosmetic imperfections. This will not affect the functionality of the product. For User Manuals and support, please follow this link to Brewtools Docs.

Read more less

The original all-in-one brewery still made in Germany! 5" touchscreen is easy to use and guides you through the brewing process Brew all-grain beer inside your home—no gas burner needed Built-in cooling jacket eliminates the need for awkward wort chillers 2R interior stainless finish with electropolished heating coil The "Mercedes®" of brewing systems. When you want the best, this is it. Never ceasing to improve upon the original Braumeister design, Speidel has taken this unit a step further with the new 5" touch screen control panel. The new automatic control system brews with your custom recipes and guides you through the brewing process. Now with integrated WiFi and bluetooth as standard, recipes and software updates can be synced automatically. Speidel Braumeister continues to be the all-in-one brewing system for brewers that demand the highest quality. The Braumeister is the original all-in-one, electric all-grain brewing system. Designed and patented in Germany over a decade ago, it has since been copied around the world. Still made in Germany today by Speidel, a 5th generation German stainless steel manufacturer, the Braumeister is the Mercedes® of brewing systems. Speidel made a decision to not try and compete on price with the rest of the all-in-one machines that are made in China. They actually went the opposite direction improving upon the Braumeister many times. They've improved the control screen, added dimpled jackets to eliminate wort chillers, improved the programming and functionality, and created an online myspeidel.com control center along with multiple other small refinements. They also created a host of optional equipment to further enhance your brewing. If you appreciate really well-made equipment, the Braumeister is for you. It is the best of the best. The welded on dimpled jacket eliminates the need for a separate wort chiller and also opens the door for using the Braumeister as a temperature controlled fermenter—see the video below. These jackets have 1" male threading, and aside from cooling, a Dump Valve tap has been added to the base of the unit to make emptying and cleaning that much easier. Advantages of the Braumeister First, the system has a small footprint and is powered by electricity, allowing you to brew inside, in a confined space, without the inherent dangers of using an open flame. Secondly, this unit is very easy to use as you mash the grain and then boil the wort in the same vessel. We also love the automation and control. Before you brew you set the controller with the different temperatures you wish to attain (advice is given on what to set) and the built-in heating element and pump do the rest. The Braumeister is especially ideal for step-mashing, which many brewers think is the preferred way to brew lager beers. Based on the results of lagers we have brewed on this machine, MoreBeer! agrees. Unlike other brew systems that have the temp probe located at the bottom, the Braumeister's temperature sensor was installed inside the middle bar. This means that the temperature is measured directly in the malt and is even more accurate in combination with the new software adjustments. Walking Through the Brew Process On Brew Day, you are going to assemble your Braumeister with the mash tub and bottom screen. You will fill the unit with filtered water to a notch on the center post - easy. The water resistant touchscreen controller reads in °C or °F, and you can set it to different temperatures you wish to reach. Advice is given in the manual. When your water is the correct temperature, a beep alerts you to add grain. Stir in your grain, lock down the top screen (so now there is a screen on the bottom and the top) and start the mash. During the mash wort is constantly recirculated through the grain bed from the bottom up, reverse of most all-in-one systems. The liquid wort flows up through the mash and then cascades down between the mash tub and the outer wall of the Braumeister. There it is collected by the pump and pushed back through the mash. At any time, you can pause the pump from the controller screen. Speidel upgraded their pump to be detachable for easy cleaning and maintenance between batches. When the mash is complete, another beep will alert you to remove the entire mash tub, which sets on top of the Braumeister to drain for a period of time. At this point you can choose to rinse the mash with hot water or to just add water directly the wort. Push another button and the boil starts and will run for however long you program it. When the boil stops, begin chilling your wort. Features: Brew in the tightest of spaces, anywhere in your home with a small footprint of counter space Easy to handle brewing and cleaning, malt pipe slides up with little effort Patented malt pipe technology. Wort is internally pumped from the bottom to the top for effective and gentle recirculation. No pipes are awkwardly mounted to the side of the kettle Clean, contactless cooling by running cold water through the welded-on cooling jacket. No need for sanitizing and storing a separate immersion wort chiller The pump is accessible beneath the unit and can be detached for cleaning and maintenance Braumeister stays up-to-date with regular software updates via an integrated WiFi module myspeidel.com syncs with the digital controller on your Braumeister Enter a recipe in myspeidel.com, choose a recipe from the community of other users, or design a recipe in Beersmith and import it to myspeidel.com and it will come up automatically on your Braumeister's touchscreen controller Edit your recipe on the fly in the touchscreen controller and it will automatically update on myspeidel.com When the brew day is over, ferment your beer inside the Braumeister, using the cooling jacket to control the fermentation temp Technical Specifications for 50L Braumeister: These units require a 220-230V connection. You should plan on hiring an electrician to install the proper socket and to wire on the appropriate plug. Produces 53L of wort, which is about 50L of finished beer Controllers can store up to ten recipes for easy repeat brewing! 3,200-watt built-in heating capacity (2) 23-watt pumps 230V (protection at least 16 amp), 50-60Hz Max Grain Capacity: 26.5 lbs Max Fill Level: 55L (Upper Marking on Center Rod) 27.5" H x 19.7" Ø 53 lbs  

Read more less