Translucent, food-grade tubing temperature rated to 500F. Odorless, tasteless, and inert Silicone tubing is FDA food-grade approved from -100F to 500F. Translucent natural color allows you to see the flow. The perfect tubing for building a personal brewery, especially for any time that the wort in contact with tubing will be above 180F. This tubing is not designed to hold pressures above 20psi. It works great with our magnetic drive pumps such as a March or Chugger pump, but we do not recommend it with a impeller pump or for use with household water pressure. Platinum Cured Quantity ordered will be shipped as multiple pre-cut lengths. Maximum length available is 100 ft. *Will burst at 30 PSI at 70F.  

Read more less

Small hose clamp suitable for 3/16" to 5/8" OD tubing Go-to clamp for anywhere you need to secure tubing Made from stainless steel These Stainless Steel small hose clamps are perfect to keep around as your go-to clamp. Use them anywhere you want to be sure your tubing will stay connected. They are perfect for silicone hoses and hooking up quick disconnects, pumps, or on any system that may need a tight seal. These stainless clamps tighten up better than cheaper ones, and the stainless steel won’t corrode. It’s handy to keep a few spares around, just in case.  Our small clamps will fit hoses with 3/16" through 5/8" OD.

Read more less

This tubing is so much better than the standard tubing most brewers start with. Silicone Tubing is odorless, tasteless, and is NSF approved as food-grade at temperatures from -100F to 500F. The translucent color allows you to see your wort flowing. It withstands high heat, which is great for any time that the wort in contact with tubing will be above 180F, which is the temperature threshold for most vinyl tubing. It doesn’t slip off of your equipment, never kinks, and easily slides on and off of barbed fittings without deforming or leaking. It is so easy to work with that once you’ve tried it on one piece of your equipment, you’ll want to upgrade your whole setup!    3/8" ID 5/8" OD Platinum Cured   Not designed to hold pressures above 20 psi. Will burst at 30 psi at 70F.    

Read more less

Thin walled tubing perfect for siphoning or tranferring liquids when not under pressure. This is the most common size hose for homebrewing that you would need to fit onto the plastic spigots (FE347), 3/8'' OD bottle fillers, and the 3/8'' OD racking canes. 3/8" ID, 1/2" OD 1/8" thick wall  

Read more less

Use for the 1/2'' OD racking cane and 1/2'' OD bottle fillers.  

Read more less

Functions the same as a standard Hose Clamp, however rather than needing to find a screwdriver (or dime!) for every adjustment you can easily tighten by hand. As an added bonus, this also has a significantly smoother inside to the clamp, which will not tear up your tubing nearly as much as a standard hose clamp!  Ideal for situations where you need to remove tubing from fittings to sanitize. Please note, as the reviews will also tell you, this is a clamp that will fit 1/2" OD tubing. If you are looking for a clamp for 1/2" ID (with 3/4" OD) choose the H955 clamp. 

Read more less

Functions the same as a standard Hose Clamp, however rather than needing to find a screwdriver (or dime!) for every adjustment you can easily tighten by hand. As an added bonus, this also has a significantly smoother inside to the clamp, which will not tear up your tubing nearly as much as a standard hose clamp! Ideal for situations where you need to remove tubing from fittings to sanitize.

Read more less

This tubing is so much better than the standard tubing most brewers start with. Silicone Tubing is odorless, tasteless, and is NSF approvedd as food-grade at temperatures from -100F to 500F. The translucent color allows you to see your wort flowing. It withstands high heat, which is great for any time that the wort in contact with tubing will be above 180F, which is the temperature threshold for most vinyl tubing. It doesn’t slip off of your equipment, never kinks, and easily slides on and off of barbed fittings without deforming or leaking. It is so easy to work with that once you’ve tried it on one piece of your equipment, you’ll want to upgrade your whole setup!    1/4" ID 7/16" OD Platinum Cured   Not designed to hold pressures above 20 psi. Will burst at 30 psi at 70F.    

Read more less

Functions the same as a standard Hose Clamp, however rather than needing to find a screwdriver (or dime!) for every adjustment you can easily tighten by hand. As an added bonus, this also has a significantly smoother inside to the clamp, which will not tear up your tubing nearly as much as a standard hose clamp! Ideal for situations where you need to remove tubing from fittings to sanitize.

Read more less

Hose clamp suitable for 3/8" to 7/8" OD tubing Go-to clamp for anywhere you need to secure tubing Made from stainless steel These Stainless Steel  hose clamps are perfect to keep around as your go-to clamp. Use them anywhere you want to be sure your tubing will stay connected. They are perfect for silicone hoses and hooking up quick disconnects, pumps, or on any system that may need a tight seal. These stainless clamps tighten up better than cheaper ones, and the stainless steel won’t corrode. It’s handy to keep a few spares around, just in case.  Stainless steel hose clamp will fit hoses with 3/8" through 7/8" OD.

Read more less

Stepless clamps are the best choice for your home draft set up. Standard worm drive hose clamps are nice for reusability, but they aren't ideal for beer and gas lines because they tend to pinch on one side, leading to leaks or degraded pressure holding capacity of your draft system. Stepless clamps apply even compression around the whole diameter of the tubing line, tightening in a perfect circle. They can be tightened with the middle cutter on a pair of pliers, or better yet, with the Stepless Clamp Tool (H1006). For tubing with 7/16" outer diameter (10.5-12.5 mm OD) Stainless steel Pack of 20 Kegland Part Number: KL06699

Read more less

This purpose built clamp tool is the easiest way to fasten our stainless steel stepless clamps.

Read more less

FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product. 5/16 inch ID tubing is recomended for use with Mini and Regular Auto Siphons. Thin wall tubing is recomended for siphoning and transferring liquids. For pumping, keg lines, or other pressurized applications, see our thick wall and keg tubing.  

Read more less

Stepless clamps are the best choice for your home draft set up. Standard worm drive hose clamps are nice for reusability, but they aren't ideal for beer and gas lines because they tend to pinch on one side, leading to leaks or degraded pressure holding capacity of your draft system. Stepless clamps apply even compression around the whole diameter of the tubing line, tightening in a perfect circle. They can be tightened with the middle cutter on a pair of pliers, or better yet, with the Stepless Clamp Tool (H1006). For tubing with 5/16" to 3/8" outer diameter (7-10 mm OD) Stainless steel Pack of 20 Kegland Part Number: KL06682

Read more less

Stepless clamps are the best choice for your home draft set up. Standard worm drive hose clamps are nice for reusability, but they aren't ideal for beer and gas lines because they tend to pinch on one side, leading to leaks or degraded pressure holding capacity of your draft system. Stepless clamps apply even compression around the whole diameter of the tubing line, tightening in a perfect circle. They can be tightened with the middle cutter on a pair of pliers, or better yet, with the Stepless Clamp Tool (H1006). For tubing with 5/8" outer diameter (14-16 mm OD) Stainless steel Pack of 20 Kegland Part Number: KL06712

Read more less

Stepless clamps are the best choice for your home draft set up. Standard worm drive hose clamps are nice for reusability, but they aren't ideal for beer and gas lines because they tend to pinch on one side, leading to leaks or degraded pressure holding capacity of your draft system. Stepless clamps apply even compression around the whole diameter of the tubing line, tightening in a perfect circle. They can be tightened with the middle cutter on a pair of pliers, or better yet, with the Stepless Clamp Tool (H1006). For tubing with 1/2" outer diameter (12-14 mm OD) Stainless steel Pack of 20 Kegland Part Number: KL06705

Read more less

This is our preferred tubing for use in Barrel Topping Systems. Because of its high elasticity this tubing is easy to attach to/detach from barbed fittings without having to cut the tubing to remove it or use hose clamps to install it (in low pressure applications). This feature allows the user to disassemble the tubing set used to deliver the top-up wine for both sanitation as well as cleaning after use. Cleans up easily and does not get stiff at low temperatures. OD is approximately 3/8" Specs: Working Pressure - 20 psi Burst Pressure - 60 psi Platinum Cured

Read more less

Insulated tubing will improve your chilling efficiency and eliminate the troublesome line sweating. This set includes two 6' lengths of 3/8" ID silicone tubing wrapped in elastomeric insulation. Hose clamps are included to secure connection points with your preferred fittings.  

Read more less

Give yourself peace of mind with this Reinforced Vinyl Brewing Tubing! This 1/2" Reinforced Vinyl Tubing is FDA approved, food grade, rated to 158 degrees F, and 200 PSI. It is the perfect tubing to use in your homebrewery with our pumps, or anywhere you want the extra security that your tubing will not kink or burst. This type of tubing is essential when putting back pressure on a system. Standard vinyl tubing and silicone are great for their own purposes, but are not designed to handle pressure, and can balloon up or explode if too much pressure is used. 1/2" ID and 3/4" OD  

Read more less

Stepless clamps are the best choice for your home draft set up. Standard worm drive hose clamps are nice for reusability, but they aren't ideal for beer and gas lines because they tend to pinch on one side, leading to leaks or degraded pressure holding capacity of your draft system. Stepless clamps apply even compression around the whole diameter of the tubing line, tightening in a perfect circle. They can be tightened with the middle cutter on a pair of pliers, or better yet, with the Stepless Clamp Tool (H1006). For tubing with 3/4" outer diameter (17-20 mm OD) Stainless steel Pack of 20 Kegland Part Number: KL06736

Read more less

The construction of this reinforced silicone tubing enables silicone tubing to handle increased pressure applications. Braided silicone offers outstanding resistance to temperature extremes and is made from FDA-sanctioned ingredients. The flexible design and construction of this tubing allows excellent bend radii and permits installation in restricted spaces without impeding flow. 1/2" inner diameter, 3/4" outer diameter Open mesh polyester braiding incorporated within the wall of silicone tubing Made from FDA-sanctioned ingredients Translucent natural color for visual contact with the flow Able to resist extreme temperature variation: -40°F to 392°F (-40°C to 200°C) Odorless, tasteless, and inert Working Pressure: 72 psi Burst Pressure: 217 psi Platinum cured Conforms to FDA CFR 177.2600, NSF

Read more less

FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product. 7/16 inch ID tubing is recomended for use with 1/2 inch Auto Siphons. Thin wall tubing is recomended for siphoning and transferring liquids. For pumping, keg lines, or other pressurized applications, see our thick wall and keg tubing.  

Read more less

Give yourself added peace of mind by using this high temp tubing on the hot side of your brewing system.   When compared with traditional silicone, EJ Beverage High Temp tubing is less likely to kink at higher temperatures. It is made of TPE (Thermoplastic Elastomer) which is an excellent alternative to high temperature PVC and Silicone.     The advantages of this high temp tubing are: PVC & BPA Free. Contains no DEHP phthalates or other plasticizers High temperature up to 135° C (275° F) Extremely low extractables Extremely low leachables High flexibility Remains flexible at high temperatures Ultra-low permeability Barrier properties 1/2” ID x 3/4” OD Environmentally friendly production - does not emit dioxins Burst Pressure = 63 psi Working pressure of 21 psi  

Read more less

Reinforced vinyl tubing is a great option for transferring your homebrewed beer. This food grade 3/8 in ID Reinforced Vinyl Tubing is rated to 158 degrees F, and 40 PSI. Use this tubing anywhere you want the extra security that your tubing will not kink, or burst. This type of tubing is useful in your setup where you want extra tubing strength, but your system pressure won't exceed 250 psi.  

Read more less

EJ Beverage High Temp tubing is perfect for use on the hot side of your brewing system.  When compared with traditional Silicone this tubing is less likely to kink at higher temperatures. It is constructed of TPE (Thermoplastic Elastomer), which is an excellent alternative to high temperature PVC and Silicone.  The advantages to this high temperature tubing are: PVC & BPA Free. Contains no DEHP phthalates or other plasticizers High temperature up to 135° C (275° F) Extremely low extractables Extremely low leachables High flexibility Remains flexible at high temperatures Ultra-low permeability Barrier properties 3/8” ID x 5/8” OD Environmentally friendly production - does not emit dioxins Burst Pressure = 54 psi Working pressure of 18 psi  

Read more less

These stainless steel butterfly hose clamps are the ideal choice for connecting silicone tubing to quick disconnects, pumps, and more. The butterfly thumb screw allows for toolless tightening and untightening, so you can build out or break down your system without rummaging through the toolbox for the right screwdriver. Fits 1/2 in. OD to 1 in. OD tubing. Actual size of the clamp is 14-25 mm (0.55-0.98 in.). Comes in a convenient zip lock bag.

Read more less

This insulated tubing kit was developed specifically for the BrewBuilt Jacketed Conical. It has all the fittings needed to connect an IceMaster Glycol Chiller to the conical jacket's 1.5" tri-clamp inlet and outlet—plus premium quick disconnects with shutoff valves that provide a "dry break" when they're disconnected. That means no cooling solution leaking all over your brewery every time you take the system apart for cleaning. The Female QDs are installed on the insulated tubing, and the Male QDs are installed on the T.C. x FPT Adapters that connect to the cooling jacket's inlet and outlet. Insulated tubing will now only provide increased chilling efficiency, it will also eliminate line sweating so you don't need to wipe up puddles of condensation that might collect on your brewery's floor during fermentation or cold crashing. Kit Includes: 1 - Insulated Tubing Set (2 x 6' lines) 2 - High Temp Plastic Female QDs w/ 3/8" Barb 2 - High Temp Plastic Male QDs w/ 1/2" MPT 2 - 1.5" Tri-Clamps 2 - 1.5" T.C. Gaskets 2 - 1.5" T.C. x 1/2" FPT Adapters

Read more less

Hose clamp suitable for 3/4" to 1-1/4" OD tubing Go-to clamp for anywhere you need to secure tubing Easily adjusted with a flathead screwdriver Made from stainless steel These Stainless Steel  hose clamps are perfect to keep around as your go-to clamp. Use them anywhere you want to be sure your tubing will stay connected. They are perfect for silicone hoses and hooking up quick disconnects, pumps, or on any system that may need a tight seal. These stainless clamps tighten up better than cheaper ones, and the stainless steel won’t corrode. It’s handy to keep a few spares around, just in case.  Stainless steel hose clamp will fit hoses with 3/4" through 1-1/4" OD.

Read more less

FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product. Thick wall tubing is recomended for pumping and pressurized systems. For siphoning and transferring liquids, see our thin wall and transfer tubing.  

Read more less

The construction of braided silicone enables the tubing to handle increased pressure applications. Reinforced silicone offers outstanding resistance to temperature extremes and is made from FDA-sanctioned ingredients. The flexible design and construction of this tubing allows excellent bend radii and permits installation in restricted spaces without impeding flow. 3/8" inner diameter, 5/8" outer diameter Open mesh polyester braiding incorporated within the wall of silicone tubing Made from FDA-sanctioned ingredients Translucent natural color for visual contact with the flow Able to resist extreme temperature variation: -40°F to 392°F (-40°C to 200°C) Odorless, tasteless, and inert Working Pressure: 94 psi Burst Pressure: 275 psi Platinum cured Conforms to FDA CFR 177.2600, NSF

Read more less

Use this reinforced vinyl tubing any place in your brewing system where you want an added layer of protection from tubing failure. This 1" ID Reinforced Vinyl Tubing is food-grade approved up to 158F. It is often used in a in a brewing system where higher pressures will be used or for commercial applications. Because it is reinforced, it is less flexible than standard vinyl tubing. Tubing has a max working pressure of 250 PSI.  

Read more less

FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product. Thick wall tubing is recomended for pumping and pressurized systems. For siphoning and transferring liquids, see our thin wall and transfer tubing.  

Read more less

Reinforced vinyl tubing is the ideal beer tubing option for transferring your homebrew that is below 158F, and is also great for water applications (such as to and from your wort chiller). This food grade 3/4 in ID Reinforced Vinyl Tubing is rated to 158 degrees F, and 150 PSI. Use this tubing anywhere you want the extra security that your tubing will not kink, or burst. This type of tubing is essential when putting back pressure on a system. Standard Vinyl tubing and Silicone are great for their own purposes, but are not designed to handle pressure, and can balloon up or explode if too much pressure is used.  

Read more less

Reinforced silicone tubing offers higher temperature tolerances and chemical resistance while remaining flexible and easy to handle. Ideal for both cold side and hot side processes and high-pressure applications. Although braided, the tubing remains transparent to allow you to visually inspect the flow of liquids. 1/2" inner diameter 3/4" outer diameter Odorless, tasteless and inert Polyester heat resistant fiber reinforcing braid Good electrical and weatherability properties Resists UV, Ozone, gases, and moisture Working Temperature: -76°F–500°F Working Pressure: 0-150 psi KegLand Part Number: KL25300

Read more less

Used primarily in aeration and oxygentation systems that call for 1/8" ID line. 3/16" OD.  

Read more less