Wine Making Hardware

Airlocks are another one of those necessary pieces of equipment for every homebrewer. If you ferment in a carboy or bucket this 3 piece airlock is a must! It’s a popular alternative to the triple ripple type of airlock because it can be taken apart and cleaned, and is easy to fill. (However we do sell the triple ripple type (FE371) in case you are used to that type and would like to stay with it.) While a simple device not all airlocks are the same. Some other designs have only a couple holes in the plastic lid and this can cause the airlock to pop out during an active fermentation. Our design features multiple holes that allow CO2 to escape easily. Additionally some other airlocks have a cross hatch design on the bottom. We have found this more easily leads to Krausen clogs and the airlock being pushed out of the fermenter. Ours is open, allowing Krausen foam to enter the airlock if necesary. Better to clean your airlock out than to find it laying on the floor next to your fermenter 3 days later. Another cool feature of this 3-piece airlock is that 1/2" ID Silicone tubing will fit onto the center post for use as a blowoff. In the cases where you are using a yeast known to produce lots of Krausen (wlp002 from White Labs or 1968 from Wyeast for example) remove the top cover, remove the plastic 'hat', and install the silicone tubing. Run the silicone tubing into a jar or bucket of water. When fermentation dies back down remove the tubing and replace the hat and cover. Please Note: Airlock only - stopper not included.

Read more less

Small hose clamp suitable for 3/16" to 5/8" OD tubing Go-to clamp for anywhere you need to secure tubing Made from stainless steel These Stainless Steel small hose clamps are perfect to keep around as your go-to clamp. Use them anywhere you want to be sure your tubing will stay connected. They are perfect for silicone hoses and hooking up quick disconnects, pumps, or on any system that may need a tight seal. These stainless clamps tighten up better than cheaper ones, and the stainless steel won’t corrode. It’s handy to keep a few spares around, just in case.  Our small clamps will fit hoses with 3/16" through 5/8" OD.

Read more less

This tubing is so much better than the standard tubing most brewers start with. Silicone Tubing is odorless, tasteless, and is NSF approved as food-grade at temperatures from -100F to 500F. The translucent color allows you to see your wort flowing. It withstands high heat, which is great for any time that the wort in contact with tubing will be above 180F, which is the temperature threshold for most vinyl tubing. It doesn’t slip off of your equipment, never kinks, and easily slides on and off of barbed fittings without deforming or leaking. It is so easy to work with that once you’ve tried it on one piece of your equipment, you’ll want to upgrade your whole setup!    3/8" ID 5/8" OD Platinum Cured   Not designed to hold pressures above 20 psi. Will burst at 30 psi at 70F.    

Read more less

Thin walled tubing perfect for siphoning or tranferring liquids when not under pressure. This is the most common size hose for homebrewing that you would need to fit onto the plastic spigots (FE347), 3/8'' OD bottle fillers, and the 3/8'' OD racking canes. 3/8" ID, 1/2" OD 1/8" thick wall  

Read more less

S-shaped airlocks are the "OG" airlocks for home beer and winemaking. They make it easy to spot fermentation activity, and have no loose peices to lose. The advantage of this type of airlock is that they have a smaller chamber so you can more closely observe the CO2 rising and therefore the rate of fermentation. They are also handy when you are cooling a beer as there is less chance of sucking airlock water back into the fermentation. They cannot be cleaned manually if they get dirty during the ferment. That is why many homebrewers prefer 3-piece airlocks for the active portion of the ferment, when the krausen (foam) from fermentation might be pushed up into the airlock. Please Note: Stopper Not Included. 

Read more less

Tri-clamp fittings are the gold standard in professional breweries and they've been widely adopted in homebrewing as T.C. kettles, fermenters, and pumps become more widely available. Tri-clamp fittings allow you to make a sanitary connection without any nooks or crannies for contaminants to hide in and they can be cleaned in place. Use anywhere you want to make a sanitary connection. 1.5" tri-clamp Made from 304 stainless steel ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.

Read more less

#7 stopper - with 3/8 inch hole. Top diameter 1.43 inches (36.3 mm), bottom diameter 1.19 inches (30 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).

Read more less

Use for the 1/2'' OD racking cane and 1/2'' OD bottle fillers.  

Read more less

Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 1.5" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.  

Read more less

You will love the versatility of this stopper!   The Universal Stopper with Hole fits a 2.8, 3, 5, 6, or 6.5 gallon glass carboy. Also fits our 500ml Erlenmeyer flask, and can be flipped over and used in most bottles! Made with a longer taper from a different material from standard stoppers to minimize popping out when wet.   Please Note: This stopper will not fit in plastic carboys, Better Bottles or Speidel Plastic Fermenters.

Read more less

Functions the same as a standard Hose Clamp, however rather than needing to find a screwdriver (or dime!) for every adjustment you can easily tighten by hand. As an added bonus, this also has a significantly smoother inside to the clamp, which will not tear up your tubing nearly as much as a standard hose clamp!  Ideal for situations where you need to remove tubing from fittings to sanitize. Please note, as the reviews will also tell you, this is a clamp that will fit 1/2" OD tubing. If you are looking for a clamp for 1/2" ID (with 3/4" OD) choose the H955 clamp. 

Read more less

Functions the same as a standard Hose Clamp, however rather than needing to find a screwdriver (or dime!) for every adjustment you can easily tighten by hand. As an added bonus, this also has a significantly smoother inside to the clamp, which will not tear up your tubing nearly as much as a standard hose clamp! Ideal for situations where you need to remove tubing from fittings to sanitize.

Read more less

Due to high demand, the case of 100 is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.   Use this foam stopper with your Erelenmeyer flask when making a yeast starter. Aeration is an important aspect of making a strong, healthy starter. This is why we recommend using a stir plate, which provides continuous aeration. This foam stopper will allow air to flow freely into your flask while keeping pesky bugs and other contaminants out. A quick spray down with sanitizer is all you need. Suitable for flasks or other vessels with an inner diameter opening of 35-45mm (1-3/8" - 1-3/4"). Reusable Resists alcohols, bases, esters, and dilute acids Autoclavable up to 249°F (121°C).

Read more less

#10 stopper - with 3/8 inch hole. Top diameter 2 inches (51 mm), bottom diameter 1.66 inches (43 mm), length 1.10 inch (28 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).  

Read more less

If you’re a beermaker who focuses on maintaining a sanitary brewing setup, you will like the advantages of using tri-clover connects any place you need to attach tubing to equipment. They make a sanitary connection that is designed to be cleaned in place.The straightforward design makes them easy to clean because there are no pockets or moving parts for bacteria to get stuck in. They make a very sturdy connection that doesn’t leak. Each connection requires a gasket and a clamp.    Product Specifications Stainless Steel 1/2 in., 1.5 in. Tri-Clamp Connection Converts 1.5" Clover to 1/2" Barb for connecting 1/2" ID Tubing.

Read more less

This tubing is so much better than the standard tubing most brewers start with. Silicone Tubing is odorless, tasteless, and is NSF approvedd as food-grade at temperatures from -100F to 500F. The translucent color allows you to see your wort flowing. It withstands high heat, which is great for any time that the wort in contact with tubing will be above 180F, which is the temperature threshold for most vinyl tubing. It doesn’t slip off of your equipment, never kinks, and easily slides on and off of barbed fittings without deforming or leaking. It is so easy to work with that once you’ve tried it on one piece of your equipment, you’ll want to upgrade your whole setup!    1/4" ID 7/16" OD Platinum Cured   Not designed to hold pressures above 20 psi. Will burst at 30 psi at 70F.    

Read more less

Functions the same as a standard Hose Clamp, however rather than needing to find a screwdriver (or dime!) for every adjustment you can easily tighten by hand. As an added bonus, this also has a significantly smoother inside to the clamp, which will not tear up your tubing nearly as much as a standard hose clamp! Ideal for situations where you need to remove tubing from fittings to sanitize.

Read more less

Size 15/16" - 1 1/16" To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole.

Read more less

Hose clamp suitable for 3/8" to 7/8" OD tubing Go-to clamp for anywhere you need to secure tubing Made from stainless steel These Stainless Steel  hose clamps are perfect to keep around as your go-to clamp. Use them anywhere you want to be sure your tubing will stay connected. They are perfect for silicone hoses and hooking up quick disconnects, pumps, or on any system that may need a tight seal. These stainless clamps tighten up better than cheaper ones, and the stainless steel won’t corrode. It’s handy to keep a few spares around, just in case.  Stainless steel hose clamp will fit hoses with 3/8" through 7/8" OD.

Read more less

#6 stopper - with 3/8 inch hole. Top diameter 1.25 inches (32 mm), bottom diameter 1.03 inches (26 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. For use with our 1 gallon glass jars (FE300). To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).

Read more less

This Stainless Steel MPT barb will connect any tubing with a 3/8" ID line to any fitting with a 1/2" FPT connection. Most commonly used to connect tubing to a ball valve. Great for brewers who want to upgrade the fittings in their brewery to stainless steel. A high quality fitting with no sharp burs around the edges.   Made from 304 Stainless Steel.

Read more less

FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product. 5/16 inch ID tubing is recomended for use with Mini and Regular Auto Siphons. Thin wall tubing is recomended for siphoning and transferring liquids. For pumping, keg lines, or other pressurized applications, see our thick wall and keg tubing.  

Read more less

Stepless clamps are the best choice for your home draft set up. Standard worm drive hose clamps are nice for reusability, but they aren't ideal for beer and gas lines because they tend to pinch on one side, leading to leaks or degraded pressure holding capacity of your draft system. Stepless clamps apply even compression around the whole diameter of the tubing line, tightening in a perfect circle. They can be tightened with the middle cutter on a pair of pliers, or better yet, with the Stepless Clamp Tool (H1006). For tubing with 7/16" outer diameter (10.5-12.5 mm OD) Stainless steel Pack of 20 Kegland Part Number: KL0669

Read more less

This purpose built clamp tool is the easiest way to fasten our stainless steel stepless clamps.

Read more less

This stopper has two holes and we use it in the production of our #10 stopper thermowell. It features one 3/8" hole and one 1/4" hole. A racking tube or stainless tube can be inserted into the 1/4" hole with the aid of some lubrifilm, forming an airtight seal, and the 3/8" hole fits an airlock. Even after you wedge all these fittings into it, it still fits a plastic carboy neck! Use this in any configuration you can think of, it'll fit: Airlocks, Thermowells, Racking Canes, and anything else you can imagine!

Read more less

Use this fitting for connecting tubing directly to your pump. 1/2" FPT on one side, with a 1/2" barb on the other. If you are not using a QD Set or a ball valve, this is a handy piece of stainless for a direct connection!

Read more less

304 Stainless steel, full port, two piece ball valves that will last for years. Easy to clean with 1/2" FPT on input and output.. High grade 304-stainless made to last with1000psi rating. We've been selling these same valves from the same manufacturer for over 10 years. This is non-locking valve meaning that it does not come with the locking clip. Many users prefer this because you are not constantly lifting the clip to open and close the valve. If you would prefer a ball valve with a locking clip please see the Brewbuilt Ball Valve.  TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and the two PTFE gaskets that form the seal when closed.

Read more less

End caps are used to close off an open tri-clamp port where a valve is not wanted or needed. They're also great for capping butterfly valves when they won't be used for a while. Give your butterfly valve a quick spray with Alpet or Star San, then cap it off to ensure the interior space remains sanitary until the next time you use the valve. For 1.5" tri-clamp fittings Made from 304 stainless steel ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.

Read more less

Stepless clamps are the best choice for your home draft set up. Standard worm drive hose clamps are nice for reusability, but they aren't ideal for beer and gas lines because they tend to pinch on one side, leading to leaks or degraded pressure holding capacity of your draft system. Stepless clamps apply even compression around the whole diameter of the tubing line, tightening in a perfect circle. They can be tightened with the middle cutter on a pair of pliers, or better yet, with the Stepless Clamp Tool (H1006). For tubing with 1/2" outer diameter (12-14 mm OD) Stainless steel Pack of 20 Kegland Part Number: KL06705

Read more less

Stopper #2 - with 3/8 inch hole. Top diameter 0.83 inches (21 mm), bottom diameter 0.63 inches (15.8 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).

Read more less

This BrewBuilt Stainless Steel Ball Valve features a locking mechanism that keeps the valve from being opened by a child or passing dog while you are brewing.  Easy to clean 2 piece design, constructed from high grade 304-stainless made to last. 1/2" FPT on input and output side. TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and the two PTFE gaskets that form the seal when closed. Features: 1/2" FPT on inlet and outlet Locking Mechanism on Handle 304 SS construction with PTFE gaskets Two-Piece Construction for easy cleaning Full Port design for minimal pressure loss / resistance BrewBuilt: Designed for Brewing, Built to Last.

Read more less

Pick up two airlock and stopper combos for a lower price! Includes two S-Shaped airlocks and two Universal Stoppers. Fits a 2.8, 3, 5, 6, or 6.5 gallon glass carboy, as well as 500ml Erlenmeyer flask. Please Note: This stopper will not fit in plastic carboys, Better Bottles or Speidel Plastic Fermenters.  

Read more less

Tri-clamp fittings are the gold standard in professional breweries and they've been widely adopted in homebrewing as T.C. kettles, fermenters, and pumps become more widely available. Tri-clamp fittings allow you to make a sanitary connection without any nooks or crannies for contaminants to hide in and they can be cleaned in place. Use this fitting to convert 1.5" tri-clamp to 1/2" male pipe thread or vice versa. If your boil kettle features 1/2" FPT ports, this fitting will allow you to attach a tri-clamp ball valve or butterfly valve. 1.5" tri-clamp 1/2" MPT 1/2" long threaded section Flat sides for easy tool adjustments Made from 304 stainless steel ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.  

Read more less

Tri-clamp fittings are the gold standard in professional breweries and they've been widely adopted in homebrewing as T.C. kettles, fermenters, and pumps become more widely available. Tri-clamp fittings allow you to make a sanitary connection without any nooks or crannies for contaminants to hide in and they can be cleaned in place. Use anywhere you want to make a sanitary connection. 2" tri-clamp Made from 304 stainless steel ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.

Read more less