Wine Making Hardware

Full Coupler with 1/2" Female Pipe Thread. Full couplers have threads for insertion from both sides. 304 stainless. Also used to connect fittings. We use with our polysulphone brewing pump, H315 to connect other fittings like quick disconnects. Length is approximately 1.5" Max pressure rating of 150 psi.

Read more less

With three places to attach tubing and accessories, this tee gives you the ability to customise your brewing setup.   304 Stainless, 1/2" Female Pipe Thread on all three openings.   2" length x 1.5" width

Read more less

Brass fitting with 1/4" flare to 1/4" MPT.

Read more less

Tri-clamp fittings are the gold standard in professional breweries and they've been widely adopted in homebrewing as T.C. kettles, fermenters, and pumps become more widely available. Tri-clamp fittings allow you to make a sanitary connection without any nooks or crannies for contaminants to hide in and they can be cleaned in place. Use this fitting to convert 1.5" tri-clamp to 1/2" female pipe thread. If your pump head comes with 1/2" MPT fittings, you can use this fitting to adapt the inlet and outlet to T.C. connection. Or adapt a boil kettle with 1/2" MPT ports to use a tri-clamp ball valve or butterfly valve. 1.5" tri-clamp 1/2" FPT Made from 304 stainless steel ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.  

Read more less

This oversized 3-piece airlock can hold 50% more water or sanitizer so your airlock is less likely to evaporate dry or get sucked dry. When the temperature drops, your fermenter will suck in solution from the airlock, and if the temperature drop is significant the airlock can be completely emptied. An empty airlock opens the door for airborne spoilants to make their way into your fermenter unchecked. The extra large 3-piece airlock offers your fermenter even more protection, and is especially useful when cold crashing.   While a simple device not all airlocks are the same. Some other designs have only a couple holes in the plastic lid and this can cause the airlock to pop out during an active fermentation.  Just like our normally sized airlock, our design features many holes in the lid that allow CO2 to escape easily.  Additionally some other airlocks have a cross hatch design on the bottom while our is open to allow Krausen foam to enter the airlock if necesary.  Better to clean your airlock out than to find it laying on the floor next to your fermenter 3 days later.     Another cool feature of this 3-piece airlock is that 1/2" ID tubing will fit onto the center post for use as a blowoff.  This can be handy if you have a really active ferment that is blowing out the top of your fermenter.     Please Note: Airlock only - stopper not included.

Read more less

1/2" Female thread on one side and 1/2" male thread on the other. Called a street elbow because of the female threads on one side and the male threads on the other. Made from 304 type Stainless Steel.

Read more less

Plug the hole in other stoppers when moving or shaking the fermenter.

Read more less

Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 2" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.  

Read more less

#3 stopper - with 3/8 inch hole. Top diameter 0.95 inches (24 mm), bottom diameter 0.71 inches (18 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).

Read more less

#6.5 stopper - with 3/8 inch hole. Top diameter 1.34 inches (34 mm), bottom diameter 1.06 inches (27 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).

Read more less

A stainless steel nipple used to combine two fittings with 1/2" FPT threads.  There is a 1/2'' space between threads.

Read more less

If you’re a beermaker who focuses on maintaining a sanitary brewing setup, you will like the advantages of using tri-clover connects any place you need to attach tubing to equipment. They make a sanitary connection that is designed to be cleaned in place.The straightforward design makes them easy to clean because there are no pockets or moving parts for bacteria to get stuck in. They make a very sturdy connection that doesn’t leak. Each connection requires a gasket and a clamp.    Product Specifications Stainless Steel 3/8 in., 1.5 in. Tri-Clamp Connection Converts 1.5" Clover to 3/8" Barb for connecting 3/8" ID Tubing.

Read more less

Useful piece for connecting tubing to a Wort Chiller. Female Garden Hose on one side, with a 1/2" OD barb for tubing on the other side.

Read more less

Give yourself peace of mind with this Reinforced Vinyl Brewing Tubing! This 1/2" Reinforced Vinyl Tubing is FDA approved, food grade, rated to 158 degrees F, and 200 PSI. It is the perfect tubing to use in your homebrewery with our pumps, or anywhere you want the extra security that your tubing will not kink or burst. This type of tubing is essential when putting back pressure on a system. Standard vinyl tubing and silicone are great for their own purposes, but are not designed to handle pressure, and can balloon up or explode if too much pressure is used. 1/2" ID and 3/4" OD  

Read more less

Solid version of FE494. A new stopper that fits a 2.8,3,5,6, or 6.5 gallon glass carboy. (DOES NOT FIT BETTER BOTTLE OR PLASTIC CARBOYS) Also fits a 500ml Erlenmyer flask. Made with a longer taper from a different material, this stopper does not pop out when wet. Much more reliable, it quickly became our stopper of choice for all applications involving these size carboys.

Read more less

For Insertion into a ball valve for connecting 1/2" ID line. Made from 304 type stainless steel.   Please note: If using 1/2" ID vinyl tubing, we recommend using hot water to heat the tubing up for easier insertion. Not recommended for use with thick wall 1/2" vinyl tubing. 

Read more less

Stepless clamps are the best choice for your home draft set up. Standard worm drive hose clamps are nice for reusability, but they aren't ideal for beer and gas lines because they tend to pinch on one side, leading to leaks or degraded pressure holding capacity of your draft system. Stepless clamps apply even compression around the whole diameter of the tubing line, tightening in a perfect circle. They can be tightened with the middle cutter on a pair of pliers, or better yet, with the Stepless Clamp Tool (H1006). For tubing with 3/4" outer diameter (17-20 mm OD) Stainless steel Pack of 20 Kegland Part Number: KL06736

Read more less

Teflon gaskets have the widest temperature range but they can be harder to get a good seal when compared to silicone and EPDM. Teflon gaskets are primarily used where the fitting may need to be rotated in place, such as a rotating racking arm. For 1.5" tri-clamp fittings Made from Teflon Temperature rated from -100°F to 500°F ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.

Read more less

The construction of this reinforced silicone tubing enables silicone tubing to handle increased pressure applications. Braided silicone offers outstanding resistance to temperature extremes and is made from FDA-sanctioned ingredients. The flexible design and construction of this tubing allows excellent bend radii and permits installation in restricted spaces without impeding flow. 1/2" inner diameter, 3/4" outer diameter Open mesh polyester braiding incorporated within the wall of silicone tubing Made from FDA-sanctioned ingredients Translucent natural color for visual contact with the flow Able to resist extreme temperature variation: -40°F to 392°F (-40°C to 200°C) Odorless, tasteless, and inert Working Pressure: 72 psi Burst Pressure: 217 psi Platinum cured Conforms to FDA CFR 177.2600, NSF

Read more less

This stopper has two holes and we use it in the production of our #6.5 stopper thermowell. It features one 3/8" hole and one 1/4" hole. A racking tube or stainless tube can be inserted into the 1/4" hole with the aid of some lubrifilm, forming an airtight seal, and the 3/8" hole fits an airlock. Even after you wedge all this junk into it, it still fits a carboy neck! Also fits perfectly into a 1.5" tri-clamp ferrule, and the stopper's flange will ensure it doesn't fall in. Use this in any configuration you can think of, it'll fit: Airlocks, Thermowells, Racking Canes, and anything else you can imagine!

Read more less

This tee fitting features 1.5" tri-clamp connections at all ends and is made from high-quality stainless steel. 1.5" tri-clamp 5.5" long x 3.75" tall Made from 304 stainless steel ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.  

Read more less

Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 3" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.  

Read more less

Our mini and medium 2-piece airlocks are a great option when a single inch could make or break fitting your carboy into a fermentation chamber. The airlock breaks down into 2-pieces for easy cleaning. Instead of a floating center piece, like standard 3-piece airlocks, the center piece is molded into the lid. One less piece to clean and misplace! Another cool feature of this 2-piece airlock is that 1/2" ID tubing will fit onto the center post for use as a blowoff.  This can be handy if you have a really active ferment that is blowing out the top of your fermenter. Holds approximately 0.4 fl oz (12 ml) Chamber - 1-1/2" tall x 1-3/8" diameter Stem - 1" long Stopper not included

Read more less

Add a 2" tri-clamp port to any tank or lid with this 304 stainless steel weldless bulkhead. Just drill a 45-47 mm hole and tighten this item to your vessel wall. For distilling purposes, this is perfect if you want to fit an extension tube between the BrewZilla / DigiBoil distillation lid and the copper pot or reflux still. Kegland Part Number: KL10979

Read more less

Useful piece for connecting tubing to a Wort Chiller. Female Garden Hose on one side, with a 3/8" OD barb for tubing on the other side.

Read more less

Tri-clamp fittings are the gold standard in professional breweries and they've been widely adopted in homebrewing as T.C. kettles, fermenters, and pumps become more widely available. Tri-clamp fittings allow you to make a sanitary connection without any nooks or crannies for contaminants to hide in and they can be cleaned in place. Use this barbed fitting to connect 1/2" ID tubing to a 1.5" tri-clamp fitting. 1.5" tri-clamp 1/2" OD barb 3/4" long barbed section 1-1/8" long stem Made from 304 stainless steel ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.  

Read more less

FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product. 7/16 inch ID tubing is recomended for use with 1/2 inch Auto Siphons. Thin wall tubing is recomended for siphoning and transferring liquids. For pumping, keg lines, or other pressurized applications, see our thick wall and keg tubing.  

Read more less

This elbow fitting features 1.5" tri-clamp connections at both ends and is made from high-quality stainless steel. 1.5" tri-clamp 90° bend 3.75" tall Made from 304 stainless steel ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.  

Read more less

EPDM gaskets have a more narrow temperature range than silicone gaskets, but they are more resistant to acids and caustic chemicals. For 2" tri-clamp fittings Made from Silicone Temperature rated from -30°F to 300°F ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.  

Read more less

Plumber's tape, or PTFE thread seal tape, is used to connect NPT (national pipe thread) style threads. Use three wraps for brass and six wraps for stainless steel. 1/2'' wide x 520'' long roll.

Read more less

If you're installing a stainless thermowell or Temp Twister Cooling Coil on your FermZilla, this pipe cutter will help make the process painless. This easy to use pipe cutter makes cutting copper, stainless steel, or aluminum tubing an absolute breeze. Easy to use and compact so it can get into tight corners and gives you a clean pipe cut. Simply hand tighten the pipe cutter onto the mark where you want to cut the pipe. Rotate the cutter around the pipe a couple of times to create a groove all around the pipe, and then each time you rotate the cutter, tighten the blade a little. Each rotation will cut a little deeper into the pipe and the cut will be straight. Suitable for 1/8"-3/16" pipe (3-22 mm) Cuts copper, brass, aluminum, steel, and stainless steel Heavy-duty one-piece slide Polished roller for easy rotation Hardened steel cutting blade Kegland Part Number: KL14557

Read more less

#10 stopper - solid. Top diameter 2 inches (51 mm), bottom diameter 1.66 inches (43 mm), length 1.10 inch (28 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. Max. Temperature Rating: 158 °F (70 °C).

Read more less

Used to connect two tri-clamp fittings together to make a sanitary connection. 304 stainless steel. For 2" tri-clamp fittings.  

Read more less

#7 stopper - solid. Top diameter 1.43 inches (36.3 mm), bottom diameter 1.19 inches (30 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. Max. Temperature Rating: 158 °F (70 °C).

Read more less

Adapt any 2" tri-clamp port or valve to work with an existing 1.5" tri-clamp fitting. The concentric design limits flow resistance as you step down from 2" T.C. to 1.5" T.C. 1.5" x 2" tri-clamp 3" tall Made from 304 stainless steel ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.  

Read more less

Monitor fermentation activity in a stainless steel conical Check flow and liquid clarity during transfers Harvest yeast and store with end caps Keep an eye on the flow during transfer or monitor yeast activity during fermentation with this 1.5" tri-clamp sight glass. Place the sight glass in-line when you transfer wort from kettle to fermenter to help you oversee how your in-line oxygenator is flowing. One of the few disadvantages of a stainless steel conical is that you can't watch the yeast as they go to work. With a sight glass you'll be able to observe how your yeast are performing throughout the fermentation process. This also makes for a great way to harvest yeast. Simply attach it to your dump valve and close off the other end with a T.C. end cap, collect the yeast and remove the sight glass, cap it at the other end and store it for your next batch. 1.5" tri-clamp Approximately 6.25" long Made from 304 stainless steel ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.  

Read more less