Everything On Sale

Easily take your beer anywhere while keeping it protected from UV! Each case contains 300 cans and lids which is enough for about 25 gallons of beer Compatible with the Cannular Can Seamer when used with 330ml table spacer (CAN103) BPA free liner Aluminum cans offer 100% protection from UV and other wavelengths of light that are harmful to beer. There's still great debate surrounding whether cans or bottles are better at keeping beer fresh, but if done correctly, cans are theoretically the superior option. When a crown cap is crimped onto a bottle, the lining of the cap can form an imperfect seal on the bottle, allowing small amounts of oxygen in, as well as small amounts of CO2 out. Over time this can result in oxidation of the beer and lost carbonation. Seamed cans form a much better seal, which can prevent these issues Aside from better protection, aluminum cans are undoubtedly the safest option for sharing and enjoying your homebrew. Bring your canned creations tailgating, camping, boating, or crack a few open poolside without the worry of broken glass! To use these cans with the Cannular Can Seamer you will also need the CAN103 table spacer. 330ml/11.1 oz aluminum cans Each case contains 300 cans and lids 202 end diameter beverage cans with B64 lids One case is enough for roughly five 5-gallon batches of beer Compatible with the Cannular Can Seamer when used with 330ml table spacer (CAN103) BPA free liner Please note that empty aluminum cans are very delicate, and up to 5% of the cans are likely to be dented or damaged in transit. If the cans were packed in a more protective (more expensive) cardboard box, the cost per can would be more expensive than simply having some dented/sacrificial cans arrive. Kegland Part number: KL13093

Read more less

The BrewZilla Polycarbonate Sight Glass comes assembled with stepless clamps and fits both the 35L and 65L units. This piece is installed in place of the stainless recirculation tube and allows you to check your fill level or watch your wort clarify during mash recirculation. Intended for use with BrewZilla model 3.1.1 or earlier. Not compatible with the Gen 4 BrewZilla. Support brackets on older models may be too small for the 0.59" OD polycarbonate tube. Includes: Stainless 1/2" Male BSP threaded post with o-rings Stainless 1/2" Female BSP threaded post with o-rings 360 mm long polycarbonate tube (13 mm ID x 15 mm OD) Please note: you may need to use varying amounts of plumber's tape to get it to seal in the right position once it has been tightened back down on the female bottom end. Warning: if using PBW, it is recommended to not have an extended contact time at temperatures above 120°F or exceeding the recommended dilution ratio.   KegLand Part Number: KL17114  

Read more less

LalBrew Wit™ is a relatively neutral wheat beer strain that can be used to produce a wide variety of wheat beer styles Produces lower levels of esters and phenols compared to traditional hefeweizen strains Provides a baseline profile of banana and spice aromas, but leaves space for the brewer to showcase other spice additions Lallemand premium brewing yeast offers brewers unmatched consistency, reliability and purity from one batch of beer to the next A more neutral choice for wheat beer styles, LalBrew Wit dry yeast displays lower ester and phenol production than traditional hefeweizen strains such as Munich Classic. LalBrew Wit provides a baseline profile of banana and spice aromas, but leaves space for the brewer to showcase other spice additions typical of Belgian style beers. Traditional styles brewed with this yeast include but are not limited to Belgian Witbier, American Wheat, Berliner Weiss, Gose, Hefeweizen, Dunkelweis, and Weizenbock . Beer Styles: Wheat beers Aroma: Fruity, slight banana and clove Attenutation: Medium to High Fermentation Range: 63-72°F Flocculation: Low Alcohol Tolerance: 12% ABV   *See the technical data sheet below for information on rehydration, usage and storage.  

Read more less

2.6 °L - Canada Malting Company. Perfectly suited for New England-style IPAs and Belgian Wits. Oat Malt has a high haze for intentionally cloudy beers. The perfect balance between easy lautering, high turbidity and rich oat flavor. Combines the flavors of traditional Pale Ale malt and toasty granola. Suitable for up to 65% of the grain bill. Use as 5 - 10% of the bill to add a light haze without significant impact on the beer's flavor. 20 - 50% will add significant turbidity and increase sweet, toasty flavor and added mouthfeel. Canada Malting is the largest malt company in Canada, producing approximately 400,000 metric tons of malt per year for brewers and distillers around the world—from the largest of multinational organizations to the smallest of craft brewers—as well as for food processors. In addition to their malt plants in Calgary, Montreal and Thunder Bay, they own and operate nine country elevators through Canada Malting Grain group. Moisture %: 4.3 Protein Total %: 11 Color °L: 2.3 - 2.9 Extract FG Dry: 60 - 64 Turbidity: 65 - 80 Beta-Glucan: 125 - 160   See the Documents tab below for Product Information and Typical Analysis.

Read more less

3.9-5.8 °L - Viking Malt - Viking Golden Ale Malt is a unique malt that contributes malty, cookie, sweet, nutty flavors to any beer where you want a more complex malt base. The name arrives from the fact that it gives beer a wonderful golden hue when used 50/50 in conjunction with pils or pale base malt.  This malt is highly modified making it very easy to convert.   Viking has done research that when Golden Ale malt is combined 50/50 with Viking Pils the resulting flavor graph is nearly identical to Maris Otter malt.   In 2016 Viking Malt and Danish Malting Group joined forces to better serve their customers. Now the new Viking Malt is the leading malting company in Northern Europe and supply raw materials and services to the global brewing, distilling and food industries. Viking Malt has 6 malthouses in areas where our distinctive Nordic barley is sourced: in Halmstad, Sweden; Vordingborg, Denmark; Lahti, Finland; Panevezys, Lithuania and in Sierpc and Strzegom, Poland. The annual malting capacity is close to 600 kilotons. Malt Specification: Moisture % - max. 5.0 Extract fine % dm - min. 80.0 Color °L - 3.9-5.8 Protein % dm - max. 11.5 Free amino nitrogen mg/l - min. 130 Kolbach index % - min. 43 Friability % - min. 85   See the Documents tab below for Product Information and Typical Analysis.

Read more less

Wai-iti® Hops – A Burst of Bright Citrus & Stone Fruit Wai-iti® hops deliver a vibrant, juicy flavor profile packed with luscious peach, apricot, and ripe citrus notes. With a low alpha acid content and smooth bitterness, this New Zealand variety shines in late additions and dry hopping, bringing bright lime zest and sweet fruit aromas to the forefront. Perfect for sessionable pale ales, hazy IPAs, and aromatic lagers, Wai-iti® offers a refreshing, delicate complexity that enhances both hop-forward and subtly nuanced brews. Looking for a soft, tropical twist? Wai-iti® is your go-to for crisp, flavorful balance.   A MoreBeer! Exclusive (or near exclusive!).  We loved this hop so much we bought almost all of the Wai-iti hops that were available in the U.S.. Available at a really great price when compared to other NZ hops.  Ballast Point made a Sculpin® Double IPA cask version with Wai iti hops that was incredible. 

Read more less

LalBrew Farmhouse™ is a non-diastatic hybrid that has been selected to make saison-style and farmhouse style beers Selected using the most advanced breeding techniques and non-GMO methods to remove the STA1 gene This strain will not produce hydrogen sulfide (H2S) off-flavors, enhancing the saison yeast aroma characteristics Lallemand premium brewing yeast offers brewers unmatched consistency, reliability and purity from one batch of beer to the next LalBrew Farmhouse™ is a non-diastatic hybrid that has been selected to make saison and farmhouse style beers. This product is the result of the research and development work of Renaissance Bioscience Corp. (Vancouver BC, Canada) in partnership with Lallemand Brewing. LalBrew Farmhouse™ was selected using the most advanced breeding techniques. The Renaissance research team used classical and non-GMO methods to remove the STA1 gene, responsible for the diastatic activity of Saison yeasts. Care was taken to retain normal brewing sugar utilization to produce dry saisons. Additionally, the patented technology from the University of California Davis (USA) ensures that the strain will not produce hydrogen sulfide (H2S) off-flavors, therefore enhancing the saison yeast aroma characteristics. Beer Styles: Farmhouse style ales Aroma: Clove, pepper, fruit notes Attenuation: High Fermentation Range: 68-86°F (20-30°C) Flocculation: Low Alcohol Tolerance: 13% ABV *See the technical data sheet below for information on rehydration, usage and storage.

Read more less

1.9-2.5 °L - Canada Malting - Canada Malting's 6-Row malt has a higher enzyme content than your standard 2-row base malt. Ideal for use in conjunction with adjuncts. Excellent base malt for use in wheat beer production. Malt Specification: Moisture % - max. 4.5 Extract fine % dm - min. 80 Color °L - 1.9 - 2.5 Protein % dm - max. 13  

Read more less

LalBrew Pomona™ offers a distinctive taste with juicy notes of peach, citrus, and tropical fruits, perfect for enhancing hoppy beers Developed through advanced yeast breeding, this hybrid strain ensures robust fermentation performance even in high ABV and highly hopped IPA fermentations Pomona™ enhances biotransformation and haze, ideal for Hazys and other modern IPA styles Lallemand premium brewing yeast offers brewers unmatched consistency, reliability and purity from one batch of beer to the next LalBrew Pomona™ is a hybrid yeast that was selected for flavor and fermentation performance in hoppy beers. Named after the goddess of fruit trees, LalBrew Pomona™ produces a unique and juicy flavor profile with notes of peach, citrus, and tropical fruits. This strain was developed by Lallemand's partner Escarpment Laboratories using advanced yeast breeding and adaptive laboratory evolution in high ABV and highly hopped IPA fermentations. Escarpment Laboratories is an innovative Canadian yeast company and industry leader in solution-based yeast development and hybridization. The result of this research and selection is a fruity, stress-tolerant, and robust strain that enhances biotransformation and haze for modern IPA styles. Beer Styles: Hop-forward beers Aroma: Peach, Citrus, Tropical Fruit Attenuation: 75-84% Fermentation Range: 64-72°F (18-22°C) Flocculation: Medium Alcohol Tolerance: > 10% ABV *See the technical data sheet below for information on rehydration, usage and storage.

Read more less

If you want a beer that tastes like it came straight from a tropical paradise, BRU-1 is the obvious choice. Developed through open pollination at Brulotte Farms in Toppenish, Washingthon, this new hop varietal is absolutely bursting with the sweet, fruity aroma of pineapple. It works well on its own for single hop beers, providing plenty of alpha acids up front in the boil and contributing complex flavors of pineapple, pear, apple and fresh cut grass when used for whirlpool and dry hop additions. It also plays well with other hops to create a depth of fruit flavor and comes highly recommended for Pale Ales, IPAs, Hazys, IPLs, and wheat ales. Hop Statistics Alpha Acids: 13.0 – 15.0% Beta Acids: 8.0 – 10.0% Alpha-Beta Ratio: 1.3 - 1.8 Cohumulone: (% of alpha acids): 35 – 37% Total Oils in mls per 100 grams dried: 1.5 – 2.0   BRU-1™ is a registered trademark owned by Yakima Chief Hops, LLC.    

Read more less

WildBrew Sour Pitch™ is a high-performance, high-purity lactic acid bacteria specifically selected for its ability to produce a wide range of sour beer styles Produces a clean and balanced citrus flavor profile typical of both traditional and modern sour beer styles Styles brewed with this bacteria include, but are not limited to, Berliner Weisse, Gose, lambic, American Wild, and Sour IPA Lallemand premium brewing yeast offers brewers unmatched consistency, reliability and purity from one batch of beer to the next Get all the tangy, sour tastes you desire in a dry culture medium with Lallemand's WildBrew™ Sour Pitch. This high performing, highly pure lactic acid bacteria is a great selection for a wide variety of sour beer styles. WildBrew™ Sour Pitch produces a clean and balanced citrus flavor profile and offers an easy way to control the introduction of bacteria during various souring techniques. Feel confident in this culture's superior performance and consistent results. An excellent bacteria for Berliner Weisse, Gose, lambics, American Wild, Sour IPAs and many other styles. Beer Styles: Sours Inoculation Rate: 1g/10L or 10g/hL Aroma: Citrus, tangy, sour Fermentation Range: 86-104°F pH Range: 3.2 - 3.5 Hop Tolerance: 4 ppm iso-alpha acid / 8 ppm beta acid   *See the technical data sheet below for information on rehydration, usage and storage.  

Read more less

The first time a brewer tries out the FastRack system they always say the same thing to themselves: “That is a thing of beauty!”   Because it’s made to hold wine bottles, the FastRack Wine Bottle Drying Rack & Storage System is just the right size for your 22oz beer bottles! It is the cleanest way to drain, stack, and store your empties. When bottling, use the FastRack to hold your bottles after sanitizing, and have them ready at hand to fill with your delicious homebrew!  The FastRack Wine takes up far less space than a bottle tree.   We sell the Fast Rack in a handy combo pack, consisting of 1 Tray and 2 Racks, which is perfect for a 5 gallon batch. We also sell the individual components for larger batches and storing more cases!    Each FastRack Wine Rack holds 12 x 22 oz (or 750 ml) bottles.   Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.

Read more less

Dual purpose hops popularly used in American styles including Pale Ales and West Coast IPAs Aroma Profile: Floral, Grapefruit, Grassy, Herbal, Pine Alpha Acids: 11.0 – 18.0% Cryo Hop® Hop Pellets Higher AA and nearly twice the resin content of traditional T-90 hop pellets Increase yield by reducing vegetal matter in your brewhouse and fermenter Cryo Hops® provide brewers with the ability to get gigantic hop character while reducing astringent and unpleasant vegetal flavors. With a substantially higher oil and resin content, LupuLN2 powder offers up all the flavor and aroma of a heavily hopped beer, but with a significanly reduced grassy character. Additionally, the lower dosage rate of the concentrated powder reduces the volume of trub and therefore, kettle loss. Using Cryo Hops® you will net more beer that is clearer! Typical usage of Cryo Hops® would be roughly 50% of pellets. LupuLN2 powder can be used in any application where traditional hop products are utilized, including: Bittering, Kettle, Whirlpool and even direct to the fermentor.  It is suggested that you use Cryo Hops® as late additions, in the whirlpool or dry hop, as the volatile aromatic compounds will be driven off if added early in the boil. Cryo Hops® are an innovative hop product that is made by separating the lupulin from the hop flower using cryogenic processing. The result is a product with twice the potency of T90 pellets, with reduced astringency and vegetative material. Note: These hops come pelletized. The powder is compressed into pellet form to make handling easier. Typical Hop Statistics: Alpha Acids: 11.0 – 18.0% Beta Acids: 11.0 – 17.0% Total Oil: 1.5 – 4.0%   Cryo Hops® is a registered trademark owned by Yakima Chief Hops, LLC.

Read more less

Instead of diffusing pure oxygen into your wort this system uses filtered air. The included air-pump pushes air through an inline sanitary filter which is then dispersed into the wort through our two micron threaded stainless steel diffusion stone. The advantage of an aeration system is that you never have to buy replacement oxygen tanks. The down side is that aeration takes longer than oxygenation. Because the atmosphere is only about 20% oxygen, the diffusion stone must be left running in the wort for approximately 30–120 minutes (however even 5 minutes of aeration is better than shaking the carboy.) There is no concern of contamination during this period, however you do have to monitor the fermenter periodically for possible over foaming. While you are brewing, this system can also be used to pre-fill fermenters with sanitary air. Replacement filters, FIL90, which need replacement every few years, are available for $4.99. About the inline filters: There are two sides to the filter - an "in" and an "out". The direction you use doesn't matter, however, you want to take note of which way you first push air through it and always keep it that way. There is an arrow on the edge of the filter housing that we use to keep the air flow going one direction when using it. The filter should never get wet, so don't try and sanitize it by dunking it in sanitizer. If you want to clean the outside of it, use Alpet D2 (CL60). To store the filter, use a little tinfoil on the "Out" of the filter and store in a zip-lock bag. The stone is attached to semirigid polyethylene tubing temp rated from -40°F to 140°F.

Read more less

These are a great add to any brewery.  Overly long so as to cover the entire forearm for reaching into sanitizer buckets, these gloves will protect you from all brew day hazards!  These will help reduce the risk of getting burned or scalded by your brew, and keep caustic cleaners and sanitizers away from your skin! 

Read more less

132-170 °L - Viking Malt - Viking Chocolate Light Malt is produced by roasting from pilsner malt. The amylolytic activity of Chocolate Malt is zero. The amount of fermentable extract is rather low. "Chocolate" refers primarily to the malt's color, not its flavor. This malt will lend various levels of aroma, a deep red color, and a nutty / roasted taste, depending on the amount used. Aromas and tastes of coffee and chocolate can be found and they are well balancing the overall taste. Chocolate Malt is mainly included in Porters and Stouts, but it can also be used for any other dark colored beers like Dark Ales due to its strong coloring value. Chocolate Malt contributes roasted flavors and aromas with hints of dark chocolate and coffee in any beer. Already with rather low dosage portions a remarkable increase in color can be found together with changes in flavor and aroma. Typical dosage rate of Chocolate Malt is normally under 5–10%. In 2016 Viking Malt and Danish Malting Group joined forces to better serve their customers. Now the new Viking Malt is the leading malting company in Northern Europe and supply raw materials and services to the global brewing, distilling and food industries. Viking Malt has 6 malthouses in areas where our distinctive Nordic barley is sourced: in Halmstad, Sweden; Vordingborg, Denmark; Lahti, Finland; Panevezys, Lithuania and in Sierpc and Strzegom, Poland. The annual malting capacity is close to 600 kilotons. Malt Specification: Moisture % - max. 5.0 Extract fine % dm - min. 68.0 Color °L - 132-170   See the Documents tab below for Product Information and Typical Analysis.

Read more less

Distilled hop oil is an amazing new product we are making available to homebrewers.  Distilled hop oil varies from other oils in that it is produced from fresh hops, as opposed to dried and processed pellets.  Distilled hop oil delivers the same wet hop character that was previously only possible to acquire with the use of freshly harvested hops.  The oil is extremely shelf stable, so you can now brew a consistant fresh hop IPA all year long. Extremely volatile, this oil should only be used for aromatic applications; typically applied at bottling/kegging.   Distilled hop oil is very potent; add to taste. We recommend using roughly 0.5-1 ml per 5 gallon batch, if replacing 50-100% of a dry hop, added directly to the beer prior to bottling or during kegging. Be careful to not push off the volatile aromatic compounds (disturb the beer as little as possible and reduce oxygen exposure). Most staff members here found that 1ml per 5 gallons was "too hoppy" when replacing 100% of the dry hop.  Hop heads (myself included), found that the 1 ml per 5 gallon dosage gave a pungent, fresh, pleasurable and unique hop experience.  Tasting these oils is as close to being in Yakima for hop harvest as possible! 

Read more less

Callista was developed by the Hop Research Center in Hüll, Germany. Its low alpha acid content and strong aromatics make it an ideal choice for late kettle additions and dry hopping. Callista's aroma and flavor profile is characterized as citrus, stone fruit, passion fruit, red berries, and gooseberry. Hop Statistics Alpha Acids: 2.0 – 5.0% Beta Acids: 5.0 – 10.0% Alpha-Beta Ratio: 0.2 - 1.0 Cohumulone: (% of alpha acids): 15 – 22% Total Oils in mls per 100 grams dried: 1.4 – 1.75

Read more less

The kiwis keep it coming with yet another hop varietal that's bursting with character. Riwaka™ varietal 85-6-23 was originally bred by New Zealand Hops by crossing Saaz with specially developed breeding selections. The result was a highly aromatic hop with almost double the oil content of its parent Saaz. Realesed in 1997, this was once an exceedingly difficult hop to get your hands on outside of New Zealand, as it was quickly bought up by the native brewers. With an almost 1:1 alpha to beta acids ratio, this rockstar aroma hop gives off strong notes of citrusy grapefruit and kumquat. Perfect for new world pale ales, IPAs, hoppy lagers, and any beer you want a bold fruity hop character to shine. Hop Statistics Alpha Acids: 4.5 – 6.5% Beta Acids: 4 – 5% Alpha-Beta Ratio: 0.9 - 1.3 Cohumulone: (% of alpha acids): 29 – 36% Total Oils in mls per 100 grams dried: 1.5   Riwaka™  is a  trademark owned by New Zealand Hops Limited Company    

Read more less

Glass carboy fermenter made from thick, high-quality, lead-free glass Perfect for fermenting beer, wine, cider, mead, and more! Clear glass allows you to monitor fermentation activity as it happens Smooth neck finish compatible with carboy hood or #7 stopper 6.5-gallon size offers plenty of headspace for vigorous fermentations If you are drawn to traditional brewing or you enjoy a simple setup, you will want to have a glass carboy for fermenting or aging your homebrew. The large 6.5 gallon size of this carboy fermenter is perfect for 5 gallon batches as there is plenty of head space to avoid blow-off during fermentation. They are made of thick, high-quality, lead-free glass which is impervious to oxygen. They do not scratch, which makes them easy to keep clean, and they're transparent so you can see what’s going on inside. This carboy will provide you with an enjoyable brewing experience for years to come. Dimensions: Height: 22.75" Width: 12.5"

Read more less

Replacement Malt Pipe Boiler Screen for 35L BrewZilla. Pull ring assembly included. For Gen 3 and older BrewZillas.

Read more less

Enigma® Hops – Mysteriously Complex, Boldly Fruity Unlock the intrigue with Enigma® hops, a uniquely expressive Australian variety that lives up to its name. Bursting with juicy red fruit character, Enigma delivers a one-of-a-kind flavor and aroma profile that defies easy description—and keeps brewers coming back for more. Expect bold notes of raspberry, red currant, and juicy Pinot Gris, layered with hints of melon, tropical fruit, and light dank resin. Depending on how you use it, Enigma can shift between lush fruit-forward brightness and a more intriguing herbal or vinous complexity, making it a versatile standout in hazy IPAs, modern lagers, and hop-forward ales. Whether you're chasing layered aromatics in a dry hop or looking to add depth in late additions, Enigma offers a mysterious, compelling twist that turns ordinary recipes into something extraordinary. Hop Statistics Alpha Acids: 14.5 – 18.5% Beta Acids: 4.5 – 6.0% Alpha-Beta Ratio: 2.4 - 4.1 Cohumulone: (% of alpha acids): 37 – 43% Total Oils in mls per 100 grams dried: 1.8 – 3.0     Enigma™ is a  trademark owned by  Hop Products Australia    

Read more less

Craft Meister Oxygen Brewery Wash is an oxygen based cleaner that dissolves quickly into solution and gets to work faster than competing products. Unlike other oxygen based cleaners, Oxygen Brewery Wash will not leave behind a chalky residue or film on your equipment. With more active cleaning oxygen than any similar product in the market and a non-caustic alkaline punch, Oxygen Brewery Wash blows away dirt and debris with ease. Works best with hot water (minimum 100 degrees Fahrenheit). For similar performance with cold water see the Craftmeister Alkaline Cleaner. Containers include a scoop for easy measuring. Feature Summary: More active oxygen than competing products Dissolves faster at lower temperatures than Oxi Clean or other oxygen cleaners Rinses faster with less water than other cleaners Cleans with active oxygen and non-caustic alkaline detergents Dilution Rates: For Fermenters, Fittings, Bottles and Tubing use 1 oz (2 scoops) per gallon of water. For heavily soiled equipment and Brew Kettles use 2 oz (4 scoops) per gallon of water. Use: Spray or immerse surfaces and allow cleaner to loosen soil for 5-20 minutes. Rinse with clean water and sanitize, if required.

Read more less

From the Hop Research Center in Hüll, Germany, Ariana was developed from a cross breeding of Herkules and an unspecified wild male hop. Although it has a high enough alpha acid content to be used for bittering, Ariana's oil content makes it an ideal choice for aroma additions and dry hopping. The aroma profile is dominated by sweet, tropical fruit notes of pineapple and passion fruit, along with citrus and berries. A delicious addition to your next Pale Ale, IPA, or Hazy. Hop Statistics: Alpha Acids: 10.0 – 13.0% Beta Acids: 4.5 – 6.0% Alpha-Beta Ratio: 1.66 – 2.88 Cohumulone: (% of alpha acids): 40 – 42% Total Oils in mls per 100 grams dried: 1.6 – 2.4  

Read more less

The same cleaning product that brewers love, conveniently pre-measured into dissolvable tablets. PBW (Powder Brewery Wash) is a non-hazardous buffered alkaline brewer cleaner. It's the cleaner of choice for many breweries, where it out performs more hazardous caustic chemicals without removing the flesh off your bones. PBW also will not corrode soft metals. It's effectiveness and ease of use has made it a go-to cleaning chemical for pros and home brewers alike. 10 g tablets are recommended for kegs, fermenters, and carboys. Use 1 tablet per 1 gallon of water. Also available in 2.5 g tablets, which are recommended for growlers, spray bottles, and glassware.

Read more less

Got built-up sediment inside your narrow-mouthed glass carboy? Luckily there’s a brush designed to reach the bottom and sides of your fermenter. The bent head of the brush makes short work of cleaning the krausen (foam on top of beer) after fermentation. This brush is made with stainless steel so you won't have any rusting issues like with other carboy brushes. Note: This brush is not recommended for plastic carboys as the metal bristle attachment can scratch the plastic. Dimensions: 26" from end of handle to 90 degree bend. Bristles are approximately 1-1/4"" in length.  

Read more less

Please Note: This part is intended to be used with the Manual Cannular Seamer (CAN10) which has been superseded by the Cannular Pro. This item will not work with the Cannular Pro (CAN110). Canning beer can be a messy business. Keep your workspace clean with this splash guard! In order to have the lowest amount of dissolved oxygen in your canned beer, you need to place the lid on top of a nice layer of foam. The problem is, once the can starts spinning, all the excess foam gets thrown off in every direction. Add this splash guard to your seamer and contain the canning chaos! This unit is specifically made for the manual Cannular model (CAN10). For the Cannular Pro splash guard, see CAN106. Kegland Part number: KL1671

Read more less

Ideal for modern American pale ales, IPAs, West Coast Pilsners, and Hazys Aroma Profile: Citrus, Tropical, White Wine Alpha Acids: 23.0 – 27.0% Cryo Hops® Hop Pellets Higher AA and nearly twice the resin content of traditional T-90 hop pellets Increase yield by reducing vegetal matter in your brewhouse and fermenter Cryo Hops® provide brewers with the ability to get gigantic hop character while reducing astringent and unpleasant vegetal flavors. With a substantially higher oil and resin content, LupuLN2 powder offers up all the flavor and aroma of a heavily hopped beer, but with a significanly reduced grassy character. Additionally, the lower dosage rate of the concentrated powder reduces the volume of trub and therefore, kettle loss. Using Cryo Hops® you will net more beer that is clearer! Typical usage of Cryo Hops® would be roughly 50% of pellets. LupuLN2 powder can be used in any application where traditional hop products are utilized, including: Bittering, Kettle, Whirlpool and even direct to the fermentor.  It is suggested that you use Cryo Hops® as late additions, in the whirlpool or dry hop, as the volatile aromatic compounds will be driven off if added early in the boil. Cryo Hops® are an innovative hop product that is made by separating the lupulin from the hop flower using cryogenic processing. The result is a product with twice the potency of T90 pellets, with reduced astringency and vegetative material. Note: These hops come pelletized. The powder is compressed into pellet form to make handling easier. Typical Hop Statistics: Alpha Acids: 23.0 – 27.0% Beta Acids: 12.0 – 16.0% Total Oil: 2.0 – 5.0%   Nelson Sauvin™ is a registered trademark owned by New Zealand Hops. Cryo Hops® is a registered trademark owned by Yakima Chief Hops, LLC.

Read more less

Perfect size for siphoning or bottling from a gallon jug.  Takes 5/16" tubing (see YMAN section below). Instructions: Sanitize and rinse your Auto Siphon. Get the inner tube gasket and the outer tube wet. Attach the curved siphon to a hose. Submerge the end of Auto Siphon into your container. If bottling directly, attach the correct bottle for the tubing you are using and place it inside your bottle wand. Otherwise place the the tubing into the container you're racking to. Pull the inner tube up until the liquid fills the tube. Pump the inner tube down and siphon will begin. Pull out the inner tube and sanitize your Auto Siphon for storage. Our standard 1/2" racking cane tips will work with this product, see our You Might Also Need section below for product information.

Read more less

A harmonious medley of distinct citrus, stone fruit, and tropical characteristics, grounded in a woody and herbal tone An excellent complement to Pale Ales, West Coast IPAs, and NEIPAs Aroma Profile: Citrus, Herbal, Stone Fruit, Tropical Alpha Acids: 9.5 – 11.5% T-90 Hop Pellets Falconer's Flight hops are a new aroma and bittering hop blend for Pale Ales and IPAs.  This proprietary pellet blend is comprised of many of the Northwest’s most unique hop varieties and is perfect for any Northwest-style IPA. Each hop has been hand selected for its superior aromatic qualities, imparting distinct tropical, citrus, floral, lemon and grapefruit tones. This allows you to get the complexity of a selection of top American aroma hops in one single addition.   Typical Hop Statistics: Alpha Acids: 9.5 – 11.5% Beta Acids: 4.0 – 6.0% Total Oil: 1.0 – 2.0%   Falconer’s Flight® is a registered trademark owned by Yakima Chief Hops.

Read more less

Cubes have a longer contact time than traditional chips do, which make them better for long-term aging of wines and beers. Also, longer contact time means longer extraction of flavors (3-6 months), which leads to a more complex combination of flavors. Chips are usually done giving flavor after a week, there by contributing a harsh, flat oak flavor. Our cubes are fires toasted and cut by Stavin, a leading supplier of high-quality oak alternatives to top commercial wineries. Download the PDF

Read more less