KegLand

Use buffer solutions to keep your pH meter calibrated. These are the same 3 solution powders that are included with the KegLand pen-style pH meter (MT624). We would strongly recommend if you haven't used your pH meter in a while to always use a buffer solution before you start your brew. Directions: Completely empty the powder into a clean glass jar Add 8.5 oz of deinoized water Stir until the powder has completely dissolved KegLand Part Number: KL06279

Read more less

Add this neoprene jacket to your Gen 4 BrewZilla to speed up heating! Heating is 10% faster and heat loss from the boiler is reduced by 50% Remove the jacket after the boil to speed up chilling Thick, insulating neoprene is secured to the boiler body with a sewn-on hook and loop fastener strap Sparge arm sleeve included to reduce heat loss during mash recirculation Add some insulation to your BrewZilla to get better boils! This neoprene jacket will help keep the heat in for quicker and more vigorous boils. Slap it on to speed up heating; take it off to speed up chilling. Also includes a neoprene sleeve for the recirculation arm to reduce heat loss during the mash. This jacket will fit Gen 4 BrewZilla models. It is not compatible with older generations of BrewZillas and DigiBoils due to where the cutouts on the jacket are located. Features: 10% faster heat up time 50% less heat loss from boiler Fits the 35L BrewZilla Gen 4 Made from 8 mm thick neoprene which is easy to wash after use KegLand Part Number: KL24365  

Read more less

The Flat Twister Lid comes with 3 pre-drilled holes perfectly sized for the Duotight bulkheads that come with the Temp Twister Cooling Coil and FermZilla Thermowell. Lid o-ring included. This lid is only recommended for FermZilla users that will be using the Temp Twister and the Thermowell together. Kegland Part number: KL15059

Read more less

This airlock made from polypropylene is much less rigid and less likely to crack compared to standard three-piece airlocks. Toss it into a bucket of sanitizer with your other equipment and don't worry about it breaking. Airlocks are another one of those necessary pieces of equipment for every homebrewer. If you ferment in a carboy or bucket this 3 piece airlock is a must! It’s a popular alternative to the triple ripple type of airlock because it can be taken apart and cleaned, and is easy to fill. (However we do sell the triple ripple type (FE371) in case you are used to that type and would like to stay with it.) While a simple device not all airlocks are the same. Some other designs have only a couple holes in the plastic lid and this can cause the airlock to pop out during an active fermentation. Our design features multiple holes that allow CO2 to escape easily. Additionally, some other airlocks have a cross hatch design on the bottom. We have found this more easily leads to Krausen clogs and the airlock being pushed out of the fermenter. Ours is open, allowing Krausen foam to enter the airlock if necessary. Better to clean your airlock out than to find it laying on the floor next to your fermenter 3 days later. Another cool feature of this 3-piece airlock is that 1/2" ID Silicone tubing will fit onto the center post for use as a blowoff. In the cases where you are using a yeast known to produce lots of Krausen (WLP002 from White Labs or 1968 from Wyeast for example) remove the top cover, remove the plastic 'hat', and install the silicone tubing. Run the silicone tubing into a jar or bucket of water. When fermentation dies back down remove the tubing and replace the hat and cover. Please Note: Airlock only - stopper not included. KegLand Part Number: KL01595

Read more less

This heating wrap provides excellent coverage for your FermZilla Conical, All Rounder, glass carboy, or PET fermenter. The large surface area ensures that heat is applied evenly to your fermenting beer. The 30-watt goes even further when paired with insulation and will lead to less temperature swings. It will provide plenty of heat while still being perfectly safe to use with plastic fermenters. And it features a convenient Velcro strap to hold itself in place—no need for electrician's tape that will leave gunky residue behind! For the ultimate temperature control with your FermZilla, pair the heat wrap belt with the Temp Twister Cooling Rod and control both heating & cooling with an Inkbird Temperature Controller. 110V plug. Approx. 39" x 9.75" KegLand Part Number: KL26048

Read more less

The classic stitch up hop sock is suitable for dry hopping or steeping grain or spices in the boil. If you have a heat exchanger, we highly recommend bagging your hops if your doing a hazy IPA, DIPA, or any highly hopped recipe, as it may clog your plates or even your pump! Rated up to 110°C (230°F). Dimensions: 130 mm wide (5.9") 580 mm long (31.4") KegLand Part Number: KL06767

Read more less

This premium Polypropylene Base Board is for the Malt Muncher 2 Roller or 3 Roller Grain Mill. Perfect for slotting over a food grade bucket, or building your own little shelf on wheels. This new design is compatible with both MaltMuncher Mills.  It has several different holes pre-drilled so either mill can be easily mounted. Board Dimensions - 17.75" x 13.5" x 3/8" Please note: Does not come with screws (M6 x 1 mm thread, 20 mm long).  2 roller mill requires 2 screws, 3 roller mill requires 4. Kegland Part Number: KL09621

Read more less

Replacement pressure relief valve rated to blow at 35 psi. This is a direct replacement of the PRV featured on the FermZilla and Kegmenter. It is also compatible with homebrew kegs and the KOMOS® CO2 regulator if you desire a lower blowoff pressure.

Read more less

Everything you need to start seaming 32 oz Crowlers with the Cannular Pro can seamer. This kit includes the Cannular Pro Semi-Auto Canning Machine, 110V Power Supply, Splash Guard Accessory, and Crowler Chuck Adapter. The Cannular Pro is a semi-automatic can seamer that is easy to use, reliable, and beautifully simple. Please note: the Cannular comes ready for sealing 12 oz and 16 oz cans as standard. The Crowler Chuck Adapter must be installed before seaming 32 oz Crowlers (Ball 300 can/end). Whether you're a brewery looking to offer canned beer to go or a homebrewer wanting to keep your creations fresh and fully protected from light, the Cannular is the answer. This bench top unit is one of the most compact and easy to use can seamers you'll find. The Cannular only requires one person to operate, and each can takes roughly 3 seconds to seam. With a two-person team, one filling and one seaming, the Cannular becomes a suitable option for nano breweries doing small canning production runs. The Cannular Pro's table spacer is specially designed to work with all standard 202 cans, including the industry favorite 16 oz (473ml) and 12 oz (355 ml) cans, as well as our 500ml (16.9 oz) and 330ml (11.2 oz) Can Fresh Aluminum Cans. Unlike the manual model that requires a secondary table spacer for use with 330ml cans, the Pro model features an adjustable platform, allowing you to raise or lower the table spacer depending on what size can you're seaming. It is necessary to adjust the table height to ensure you have the appropriate amount of pressure applied when the can lift is raised. Operation: The beauty of the Cannular lies in how truly simple it is to operate, and the semi-automatic pro model makes canning beer even easier. With only three points of operation, it only takes a few minutes to familiarize yourself with the machine. The seaming process is as follows: Place lid atop the can and place the can on the table spacer Turn the platform lever clockwise to raise the can to the seamer Press the seaming operation button then wait for the can to stop spinning Turn the platform lever counterclockwise to lower the can That's all there is to it! Construction: The Cannular was designed to be compact, durable, and safe to operate in a wet environment. The platform assembly is made from 304 grade stainless steel, so no matter how messy your canning gets, there's no need to worry about rusting or degradation. The body of the unit is made from hammered sheet metal and fastened together with stainless steel screws. Rubber feet help keep the unit from slipping and sliding while in use. In addition, the Cannular features built-in brackets near the feet so you have the option to mount the machine to your counter or benchtop. The Cannular runs off of 24V DC power via the Anderson socket located on the back. This lower voltage was chosen specifically to make the unit as safe to use in a wet environment as possible. Kit Includes: Cannular Pro Can Seamer 110V Power Supply Splash Guard Crowler Chuck Adapter Cannular Pro Specifications: Power: 250W 24V DC Rated Speed: 3300 RPM Gearbox Ratio: 9.8 : 1 Dimensions: 16" L x 9.5" W x 21" H Weight: 40 lbs   Please note: When you receive your cannular the rollers have been set and tested at the factory. They should not need adjustment for 100,000 cans. The table, however, comes unadjusted and getting it set up correctly is very important to getting a proper seal. Cannular's test show that a .4mm (.015") actual overlap is all that is needed to seal to 90 PSI. The proper table tension takes a little practice and expect to waste a few cans getting it dialed in. Once you learn the proper tension re-adjusting it is very quick and easy. You want the tension to be tight but not so tight as to dent the can. Use cans at your fill height with water for proper tension adjustment.   Cannular Compact Semi-Auto Canning Machine | User Guide  

Read more less

Get your grain bed evenly mixed and break up dough balls in seconds! Using a handheld electric drill, this heavy-duty stirrer makes mashing in a breeze Made from all stainless steel with a 1/4" hex head to securely attach to your drill This stainless mixer attaches to an electric drill for easy and thorough mixing of your mash. To get the best mash efficiency it is important to break up dough balls (clumps of grain) and ensure that the grain bed is not compacted.  Allowing maximum recirculation through your grain bed will always yield higher extraction / efficiency rates of your brew. Are far as mixing grain goes, this stirrer is much more efficient and less time consuming than a mash paddle or large spoon. Simply attach to your portable electric drill and secure the 1/4" hex head tightly. Overall length is 23.5" with a mixer diameter of 2.75". Highly recommended for all sizes of BrewZillas. KegLand Part Number: KL32247  

Read more less

This Duotight Bulkhead is the same one used for installing the Temp Twister cooling coil into the lid of the FermZilla. Allows you to add a bulkhead to just about anything that can then be connected to with EVABarrier 9.5 mm OD Tubing (D1719) or 3/8" OD stainless or copper tubing. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL14564

Read more less

Suitable for both hops and steeping grains. We highly recommend using a steeping bag for hops to keep vegetal matter contained in the boil kettle and out of your fermenter. If you use a counterflow chiller or plate chiller for cooling, filtering hops is even more important as these devices can clog if too much hop matter passes through them. The hop sock does not have a drawstring. You will want to tie the end in a knot to keep it closed. Dimensions: 150 mm wide (5.9") 800 mm long (31.4") KegLand Part Number: KL01281  

Read more less

Upgrade your MKII pump with a 304 stainless steel replacement head. Stainless steel is more durable if you are attaching ball valves. Very occasionally the threads on the plastic head that comes standard on the MKII can break if you are using hard to close ball valves that apply a lot of torque. Stainless steel is very robust and will not break, is food grade, and well... stainless. Before you snag the stainless center-inlet head, also consider the stainless inline tri-clamp head. Kegland Part Number: KL03865

Read more less

Reduce heating time during your mash with the Gen 4 BrewZilla Redistribute recirculating wort for longer heating element exposure Improve heat distribution throughout the mash Speed up heating times with the Heat Exchanger Dish (HED) for Gen 4 BrewZillas. This optional upgrade accessory redirects the flow of wort so that it spends more time exposed to the heating elements before reaching the center drain at the bottom of the kettle and being recirculated. Due to the concave bottom and central draining hole on the Gen 4 BrewZilla, recirculating wort will pass through the malt pipe and then down through the boiler false bottom following the path of least resistance. This can cause wort to make a B-line for the drainage hole and reduce the wort's exposure to the unit's heating elements. With the HED installed, wort will be directed to the edge of the BrewZilla base and pass over the elements for a longer period and reduce the time needed to heat to your set temperature. For use with the Gen 4 35L BrewZilla. It is not compatible with any previous generations of BrewZillas or DigiBoils. The HED has been pressed into a slight concave shape to match the curvature of the boiler false bottom. Includes a longer eye bolt assembly than the one included with the false bottom. NOTE: The order of bolt to washer to nuts goes as follows. Eye bolt, washer, false bottom, washer, nut, HED, then wing nut. This is so that the eye bolt does not come completely removed when and if you clean underneath the Heat Exchanger Dish. KegLand Part Number: KL29353

Read more less

This Duotight reducer fitting can be attached to the Intertap Short Shank with 1/4" Duotight compatible barb (D1242). Compatible with EVABarrier 9.5 mm OD tubing (D1719). Also attaches to the Plastic Ball Lock Cap, allowing the cap to be used with 9.5 mm OD EVABarrier. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL08648

Read more less

Completely impervious to oxygen and sunlight and made from 304 stainless steel, this growler is one of the best storage options for beer. This growler comes with a double wall vacuum insulation keeping your delicious beer cold for hours. The spring wired lid makes this growler capable of holding up to 30 psi. This is a smokin deal when compared to other double wall growlers. Dimensions: 4.75 in. Diameter x 12 in. Height; Holds 2L or 67 oz Draft Kit is out now! Kegland Part number: KL04282

Read more less

One of the great features of the KegLand pH Meter is the replaceable probe. The probes of pH meters wear out through normal use. Instead of making you buy a whole new pH meter you can just get the probe! Kegland Part Number: KL04176

Read more less

The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required. Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing. 6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length. Duotight Push-to-Connect These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done! Compact The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines. Overmolded Poppet The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out. Tool-less Disassembly Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects. Extreme Chemical Resistance No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing. Toughness This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough! High Flow The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects. Features: Ball Lock Quick Disconnect - Gas In Direct connect EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Disassemble by hand for quick and easy cleaning Three sizes available: 6.35 mm (KL24242) 8 mm (KL20756) 9.5 mm (KL20770)

Read more less

The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required. Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing. 6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length. Duotight Push-to-Connect These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done! Compact The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines. Overmolded Poppet The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out. Tool-less Disassembly Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects. Extreme Chemical Resistance No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing. Toughness This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough! High Flow The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects. Features: Ball Lock Quick Disconnect - Bev Out Direct connect EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Dissamble by hand for quick and easy cleaning Three sizes available: 6.35 mm (KL24235) 8 mm (KL20749) 9.5 mm (KL20763)

Read more less

Swap out the standard BrewZilla recirculation arm with this flexible upgrade Perfectly position your recirculating wort or sparge water over the grain bed Use the BrewZilla's built-in pump to easily transfer wort to fermenter or clean the kettle with a CIP head This simple upgrade for the BrewZilla is perfect for positioning your recirculating wort or sparge water over the grain bed and makes it even easier to use the unit's built-in pump for transferring wort to your fermenter or for CIP at the end of the brew day. Pairs perfectly with the Sergeant Sparge Head for mashing and sparging, as well as the BrewZilla Spinning Spray Rotor to clean your kettle. Please note: Camlocks sold separately. You will need a Male Camlock x 1/2" Male Thread adapter in order to attach the Flexi Arm to your BrewZilla recirculation piping. Specifications: 304 Stainless Steel Fitted Female 1/2" Hex Nut Ends Silicone Washers Included Length 31.5" KegLand Part Number: KL15097

Read more less

Take the guesswork out of oxygenation with this handy flow meter. If you're using pure O2 to oxygenate your wort, you're likely using a disposable cylinder with a simple brass regulator, and have no way to measure how much oxygen is actually being added. You're essentially left to finding the "sweet spot" on the dial when you open the regulator and aim for the same spot on the next use. Get repeatable results by adding this flow meter to your setup. This device will allow you to dial in the flow rate and help you add the same amount of oxygen from batch to batch. The flow meter comes with male flare thread inlet and outlet and includes two Duotight fittings. It's ready for use with 8 mm OD EVABarrier tubing right out of the box, or you can add a swivel nut and barb for use with other size tubings. Once yeast pitching temperatures are reached, we recommend using a 0.5 micron diffusion stone and adding pure O2 at a 1L/minute flow rate for 60 seconds to acheive the recommened 10-14 ppm dissolved oxygen. Features: 1/4" Male Flare Inlet/Outlet Duotight Fittings for 8 mm OD Tubing Included Scaled for 0.1 to 1.5 L/min Flow Rate 3.6" H x 0.9" W Kegland Part number: KL13185

Read more less

If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 4 mm (5/32") ID size is perfect for homebrew draft applications where only a short beer line is needed. We recommend using 5-6 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 4 mm (5/32") Outer Diameter - 8 mm (5/16") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. Kegland Part number: KL06224

Read more less

Track your mash tun run off during sparging, pre-boil gravity, post-boil gravity, and starting gravity before fermentation Readings are almost instantaneous, requires only a few drops, and there's no need to cool your sample thanks to ATC Triple scaled for use in brewing, winemaking, and distilling LED illumination makes it easy to see your readings even in low light environments like your garage or basement Water resistant enclosure—dip the refractometer into your wort without risk of damaging the LED light Includes case, pipette, and USB magnetic charging cable If you want a quick and easy way to take gravity readings during the brewing process, then a refractometer is the tool for the job. Taking hydrometer readings during the brew tends to be a time-consuming process, and by the time you get a reading it may be too late to react. This is because you need to take a large sample and cool it to get an accurate reading. A refractometer allows you take instant gravity readings, with just one drop, at any point during the boil, or even during the run off of the sparge during an all-grain brew. These 'during the process' readings allow you to add more water or boil longer so you can attain exactly the gravity you desire. Traditional refractometers without ATC are calibrated to work at 68°F. The ATC function allows you to use the refractometer in an ambient temperature range of 50-86°F (10-30°C). Since your sample is just one drop, and will quickly adjust to the temperature of the refractometer, the temperature of the sample is irrelevant. This unit also comes with a manual calibration knob that is secured with a lock nut. To calibrate place one drop of distilled water on the testing platform and adjust to zero if necessary. The LED light is a handy feature that helps illuminate the sample and make the scale easier to read. Features: Triple Scaled 0-32 Brix 0-1.130 Specific Gravity for Wort 0-1.130 Specific Gravity for Sugar Water resistant enclosure Adjustable focus eyepiece with rubber grip Automatic Temperature Compensation LED illumination function Rechargeable battery Please Note: The Sabre Refractometer is used to measure unfermented wort. Once alcohol is present, the use of a correction table is advised. KegLand Part Number: KL25072

Read more less

This Duotight to 1/2" female thread fitting can be used to connect beverage or gas line to fittings with 1/2" male threading. Compatible with EVABarrier 9.5 mm OD Tubing (D1719). Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL13871  

Read more less

Perfect for spraying down brewing equipment with dissolved cleaners or sanitizers Attach the optional Ball Lock Keg Post Adapter to convert the sprayer into a line cleaning device Empty the large 33.8 oz tank up to 30 times on a single charge The Power Sprayer is a fantastic multi-purpose device that can be used for spraying down your brewing equipment with cleaners and sanitizers or converted into a pressurized line cleaning system. The tank features graduated volume markers and can be emptied up to 30 times on a single charge. The nozzle knob can be adjusted to turn the stream into a fine mist or a powerful jet. This product is made from food grade Santoprene, PP, PE, Silicone and stainless components. Battery Life The pump has large 18650 li-ion rechargeable battery. On a full charge the battery will empty the tank 18-30 times so it lasts for ages. If you use fine mist it will be closer to 18 times but if you use a jet/stream the battery will last closer to 30 times. Includes: 33.8 oz Reservoir Tank Power Sprayer Nozzle and Dip Tube White Plastic Adjustment Head Sprayer 6" USB-C to Standard USB Cable *Does not include USB wall charger KegLand Part Number: KL40860

Read more less

The lowest price Pressurizable fermentor out there. Perfect for most ales that ferment in 2 weeks or less Super smooth PET makes cleaning very easy Transfer to your keg closed and under pressure oxygen free PET is better oxygen barrier than fermentors made of HDPE Super lightweight yet strong and shatterproof The FermZilla All Rounder is the most affordable pressurizable fermenter on the market. Although it doesn't feature a dump valve like the FermZilla Conical, the All Rounder carries the same pressure rating, making it an absolute steal if you're looking to ferment under pressure, perform pressure transfers, or want to carbonate and serve directly from the fermenter. The All Rounder is made from super smooth PET that's easy to clean, and the simple design means no nooks or crannies for microbes to hide. With a 4.75" lid opening, you'll have no trouble getting your arm inside to scrub away stubborn krausen rings. As with all FermZilla fermenters, the lid features molded drill locations that make installing accessories like a thermowell or Temp Twister Cooling Coil a breeze. In order to unlock the full potential of the All Rounder, you'll want to pick up the 55L FermZilla Pressure Kit. The pressure kit is available with either stainless or plastic ball lock caps. Why MoreBeer! loves the All Rounder FermZilla: Super smooth PET makes cleaning very easy. Pressure rated lid and PET material make for a better oxygen barrier than fermenters made of HDPE. Lightweight and easy to move around, yet strong enough to be considered shatterproof. The 4.75" lid opening makes it easy to get your arm inside and clean after use. The lid is designed for the easy installation of accessories such as a thermowell or cooling coil. Price! A pressurizable fermenter in this price range is an incredible value, and it opens the door for many cold-side processes that can't be done in a normal carboy or plastic fermenter. What's Included: FermZilla 60L All Rounder Fermenter Stainless Steel Stand Stainless Steel Handle Top Lid with PRV (35 psi) 3-Piece Airlock Adhesive Thermometer Specs: 60 L (15.9 gal) Total Volume Pressure Rated to 2.5 Bar (36.2 psi) Height in Stand - 34" Height w/ Airlock - 36.5" Tank Diameter - 13.9" Lid Ports - 28 mm PCO 1881 threads Temperature Rating: When not under pressure, do not expose to liquids above 131°F When under pressure, do not expose to any temperatures above 95°F* *Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years. Kegland Part number: KL15196   NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary. FermZilla All Rounder 30L & 60L | User Guide

Read more less

A perfect pocket temperature probe for homebrewing and BBQ! Check the temperature of your mash, whirlpool additions, or see if that mouthwatering tri-tip is ready to be pulled off the grill. With a range of -58°F to 572°F there's basically no way you won't get a temperature reading unless you live in an active volcano (do not recommend). Specifications: Range: -58°F – 572°F (-50°C – 300°C) Resolution: 0.1°C Temperature Error: +-1°C (0~100°C) Power Supply: 1 x AG13 Battery (included) Functions: On/Off °C/°F Hold KegLand Part Number: KL23320

Read more less

If you've been looking to step up from fermenting in plastic buckets or carboys, this is an excellent choice for your next fermenter. Stainless steel is a much better option than glass or plastic, as it is extremely easy to clean and virtually lasts forever. There's also much less chance of contamination as stainless doesn't scratch like plastic. Over time, you'll get scratches in plastic fermenters from normal wear and tear, creating microscopic havens for bacteria. Meanwhile, glass carboys are always at risk of breaking which is something you will never have to worry about with stainless steel. The Bucket Buddy is a great value if you're looking for a stainless steel fermenter with built-in heating control. If you live in a cold climate, ale fermentations may be a seasonal affair, as cold ambient temperatures can easily drive down the temperature of your wort below your yeast's optimal fermentation temp range. The Bucket Buddy offers a simple solution with an integrated heating element and digital temperature control. Program your fermentation temperature and if the temp drops below your set point the unit will gently heat your wort from the bottom up via the concealed element located in the base. For cooling, you can place the fermenter in a dedicated refrigerator or drill into the lid to install a Temp Twister Cooling Coil. A temperature controller probe can then be taped to the side of the fermenter to control your cooling source, or you can drill another spot in the lid for a thermowell. Another advantage over carboys and plastic buckets is the domed base inside the fermenter which is great for yeast flocculation when fermentation is complete. The included racking arm will make it easy to transfer out every last drop of beer while leaving the yeast cake undisturbed. The entire racking arm and ball valve assembly is weldless, which means you can remove the assembly to clean and sanitize it between batches. You can even boil the assembly for added assurance that it's been sterilized. To help maintain a steady temperature and cut down on power consumption, the Bucket Buddy pairs well with either the BrewZilla Neoprene Jacket or the FermZilla Insulating Jacket. This unit comes standard with silicone tubing to transfer from the ball valve to your bottles or cans, as well as a stopper and airlock for the domed lid. Specifications: 304 stainless steel construction 9.25 gallon total capacity Digital temperature control 110V / 36W power Stainless steel outlet valve with rotating racking arm Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C External Dimensions: 28" H x 15" W (including handles) Internal Dimensions: 22" H x 11.75" W Please note: Heating capacity is highly dependent on ambient temperature and use of insulation. Testing has shown that the Bucket Buddy can heat to 104°F in a room temperature ambient environment without insulation. Adding insulation may increase heating capacity while colder ambient environments may lower heating capacity. KegLand Part Number: KL20695

Read more less

The Ultimate FermZilla Combo Pack! Get the FermZilla Easy-Grip Tri-Conical & our most highly recommended accessories at an unbeatable price! Includes some of our favorite accessories for the FermZilla, such as the Pressure Kit with Floating Dip Tube so you're always racking the clearest beer, Duotight BlowTie 2 for pressure fermentations and flow control keg transfers, and Insulating Jacket to help maintain stable fermentation temps These accessories will help unlock the FermZilla's full potential, so buy them together and enjoy the savings! Combo Pack Includes: FermZilla Tri-Conical Easy-Grip Fermenter | 27L | 7.1G Pressure Kit w/ Floating Dip Tube Duotight BlowTie 2 Spunding Valve Insulating Jacket FermZilla Tri-Conical Easy-Grip Fermenter The FermZilla is the perfect option for brewers that want all the advantages of a conical fermenter without the price tag of a full-blown stainless-steel unit. It allows you to dump trub, harvest yeast, and with the addition of CO2 cylinder and regulator, you can carbonate and serve – all in one vessel! The clear PET tank allows you to visually monitor fermentation activity and is pressure rated to 2.4 Bar (34.8 psi), which means you can ferment under pressure, reducing ester and fusel alcohols in your finished beer. This also gives the ability to perform pressure transfers. If you prefer to move your finished beer to a keg or other vessel, you can do so with little to no oxygen exposure. The FermZilla Tri-Conical Easy-Grip model comes packed with accessories so you can take full advantage of this pressurizable fermenter on day one. The new stock standard includes Easy-Grip threaded lid ring, BlowTie spunding valve with integrated pressure gauge, ball lock carbonation caps for the lid and collection container, floating dip tube kit with weighted filter, volume marker graduation sticker, and adhesive thermometer.  What's Included: FermZilla 27L Tank with 3" T.C. Bottom Port Easy-Grip Threaded Lid Ring Integrated Gauge BlowTie Kit Spunding Valve (0-15 psi) Silicone Dip Tube Kit with Yellow Weighted Filter and SS Float (2) Yellow Liquid Carbonation Caps (2) Red Gas Carbonation Caps Fermzilla Pressure Lid with Red PRV (35 psi) 3" T.C. Butterfly Valve 600 mL Collection Container with 3" T.C. Connection Stainless Steel Stand with Swing Handles 3" tri-clamp with gasket Graduation Sticker Adhesive Thermometer Specs: 27 L (7.1 gal) Total Volume Pressure Rated to 2.4 Bar (34.8 psi) Height in Stand - 30.2" Tank Diameter - 13.9" Diameter in Stand - 15.3" Lid & Collection Container Ports - 28 mm PCO 1881 threads Temperature Rating: When not under pressure, do not expose to liquids above 131°F When under pressure, do not expose to any temperatures above 95°F* *Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years. Please note: when using the FermZilla under pressure, you must perform a water pressure check to ensure your connections are leak proof. To do this, fill your FermZilla up with water, apply at least 15 psi pressure, and check for leaks around all caps and threads.   Pressure Stress If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple: Fill the tank to the brim with water Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher Pressurize the tank to 4 BAR (58 psi) Check for leaks, then replace the Red PRV when finished If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla. General Care Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank.   KegLand Part number: KL47296 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.   FermZilla Tri-Conical 27L & 55L | User Guide

Read more less

No more spillovers! Set your desired volume and walk away Automatically collect water while you tend to other tasks Great for collecting brewing water or mixing your cleaning and sanitizing chemicals Illuminated display in splash resistant housing Integrated solenoid valve cuts off flow when your set volume is dispensed 1/2" BSP inlet and outlet work well with Duotight or Type A Camlock fittings Unlike other hose timers that simply measure time, the Fill-O-Meter measures volume and will automatically turn off when the programmed volume of water is dispensed. Enter your desired volume of water, press Start, and tend to other brew day prep work. Install in-line with your water filter to automatically collect filtered strike water, or measure out how much water you need to mix with cleaning chemicals for a precise dilution ratio. We recommend setting up the Fill-O-Meter with either Duotight fittings or Type A Camlocks. Thread tape will be required for the Camlock. Use sparingly as too much plumber's tape can damage the plastic thread. And it is very important to never overtighten! Displays real time flow rate and volume (Liters/Min or Gallons/Min) Accurately measures and controls volumes at flow rates from 1-30L/Min (0.26-7.9Gal/Min) Never overfill or spillover again Splash resistant housing Great for filling tanks, brewing kettles, distilling gear, mixing liquid and many other applications Integrated flow meter and solenoid valve Illuminated display for usage in the evening Integrated sound alarm Easy 1/2" BSP Inlet and Outlet Automatic failsafe - flow is stopped if the unit loses power Important Notes: DO NOT flow liquid the wrong direction, it will break the unit. DO NOT overtighten fittings onto the 1/2" ports. DO NOT exceed temperatures greater than 104°F (40°C) through the unit. Specifications: Flow Range: 1-30L per minute Temperature Range: 32-104°F (0-40°C) LCD: 3 inch back lit display Housing Material: ABS Input/Output threads: BSP 1/2" Pressure Rating: 0-12bar (0-180psi) Accuracy: +/- 5% Please Note: Accuracy can be improved with stable flow. Repeated start/stop or variation in water supply can have negative effect on accuracy. If you are noticing innaccurate fill levels, see the instruction manual for calibration instructions. KegLand Part Number: KL14694  

Read more less

A distiller's parrot is a piece of equipment that allows you to take alcohol gravity measurements using an Alcometer continuously throughout your pot or reflux run. It should be placed inline of your distillation outlet so that the drops of distillate fall directly into the tallest collection cone. But it should only placed in-line after you collect your foreshots. Your alcometer is then gently placed into the lower cone. Be careful not to drop in the alcometer before there is any liquid/distillate in the cone, as dropping it into an empty cone could break your glass alcohol meter. Specifications: Max Capacity: 105 ml (w/o alcometer) Weight: 1.9 lbs Made from 304 Stainless Steel Kegland Part number: KL14823 I.D. of 19mm (0.74") Does not include alcohol meter.  

Read more less

Adjustable relief valve installs on standard ball lock keg posts Use with any ball lock keg to control flow during closed pressure transfers Integrated pressure gauge can be swapped out with a digital gauge or large face dial gauge for easier, more accurate readings Adjustable black cap can be swapped out for color coded PRVs with a fixed pressure Low-profile design only measures 1.75" in height This easy to use and compact pressure relief valve is super handy for keg transfers. Using a ball lock quick disconnect as the main body, the valve easily snaps onto ball lock keg posts. Adjustable relief valves are a great way to limit oxygen exposure and regulate flow during closed keg transfers, The included gauge reads from 0-30 PSI and can be swapped out with a digital gauge or large face dial gauge for easier, more accurate readings. The black pull ring cap on the other end can be rotated for adjustments, or swapped to a range of color coded PRVs for a fixed pressure. This low-profile option only measures 1.75" in height. It works right out of the box but has several upgrade options as shown in the images. Warning: Never swap out the valve's standard PRV with a color coded PRV that exceeds the pressure rating of your vessel. Features: Duotight fitting where the gauge attaches This allows for upgrading the valve with a digital gauge or larger analog gauge Manual pull ring pressure relief This allows for you to not only adjust the pressure with the black rotary knob but also use the ring pull to instantly release pressure if you want to release manually Option for several color coded PRVs to be used (see below) Yellow - 17 psi Red - 35 psi Green - 65 psi Gray - 100 psi KegLand Part Number: KL29438

Read more less

Upgrade your FermZilla Conical or All Rounder with the new 2" Tri-Clamp Lid from KegLand. Add yeast, hops or even take samples from a wine thief from the top and not have to remove the entire lid. This particular lid was designed in order to suit a growing number of customers desire to dry hop without exposing the batch to oxygen from opening the lid. By using this lid in conjunction with the FermZilla 2" Butterfly Valve and Hop Bong Kit, you will be able to purge CO2 into the tube and expel all the oxygen inside it and dump freely into the vessel. Features: (2) PCO1881 Male Ports Recommended for use with Red (Gas In) & Yellow (Bev Out) Ball Lock Caps PRV Port with Red 35 psi (2.5 BAR) PRV 2" T.C. Ferrule Undrilled Ports (for optional accessories): Thermowell Port (see below for FermZilla Thermowell kit) (2) Temp Twister Ports Please Note: Temp Twister will need to be bent on a 20° Angle in order to fit on the curved lid and align vertically in the tank. Also includes: 2" Tri-Clamp 2" T.C. Gasket 2" T.C. x PCO1881 Male Thread Cap If you ever need to replace the O-ring attached to the bottom of the Pressure Lid, a Corny Keg Lid O-ring fits perfectly. KegLand Part Number: KL28219 Warning: Always depressurize your system COMPLETELY before removing fittings from your fermenter. Warning: Only use Red 35 psi PRV with this lid. Ensure the PRV is cleaned and dried of sticky residue before each fermentation. Failure to do so could cause injury and void warranty.

Read more less