Draft

This plastic ball lock cap features soda bottle threads, allowing you to convert a 1 or 2 liter soda bottle into a convenient travel growler. The ball lock is compatible with both gas and beverage disconnects, so you can charge the PET bottle before you leave the house and dispense on the go. Attach 3/16" or 1/4" ID tubing to the barb to serve as your dip tube and you're all set! These caps also work great for quickly and conveniently cleaning your draft lines. Mix up a small batch of line cleaning solution in a soda bottle, attach the ball lock cap, and then connect it to your beverage line. Place a bucket below your tap to catch the cleaning solution and open your faucet. Then simply turn the bottle upside down and squeeze it to push solution through your line and out the faucet. You can also choose to pressurize the bottle first, but squeezing the solution through is just as effective. Fermenting with the FermZilla? This is the same ball lock fitting included with the FermZilla Pressure Kit and it's also compatible with the FermZilla Collection Container. If you use the collection container to add dry hops, attach one of these caps and you'll be able purge the container of oxygen before opening the dump valve to introduce the hops. Attach some tubing and diffusion stone and you can oxygenate your wort through the collection container as well! When using two ball lock caps, we recommend pairing this red plastic cap with a yellow plastic cap so you can easily identify which caps are being used for liquid or gas. The barb is Duotight compatible. If you'd like to use the cap with 8 mm OD EVABarrier tubing, see DUO10. For a stainless steel option see KG50. Specs: Liquid and Gas Ball Lock Compatible Overall Length - 2.5" Barb Length - 7/8" Barb OD - 1/4" Barb ID - 3/16" 28mm PCO 1881 Threads Kegland Part number: KL1078

Read more less

BLC, also known as Beer Line Cleaner, is a preferred alkaline based draft line cleaner. Used to remove bacteria and loosen mineral deposits from beverage lines, faucets, etc.. Can be used with all type of cleaning systems and al types of draft set ups including long draw commercial systems, homebrew set ups, kegerators, draft box lines, etc.. Can be used with cold or warm water. No hazardous shipping.   Instructions for use: Add ½ oz BLC for each quart of water.  Drain out beer and run solution into line.  Circulate or let stand in lines for at least 15 minutes  Flush cleaning solution from line and rinse well with clean water. 

Read more less

Automatically release pressure inside your fermenter during pressure fermentations Regulate beer flow during pressurized transfers from fermenter to keg Large triple scale pressure gauge with extended 0-40 PSI pressure range Diaphragm spunding valves offer higher accuracy compared to spring & poppet spunding valves Comes complete with ball lock QD, Duotight adapter, tee, and rigid joiners With this complete kit you'll be ready to use the Blow Tie Spunding Valve right out of the box. The BlowTie is used to release excess pressure on a pressurized fermenter or from a receiving keg during pressure transfers. This diaphragm spunding valve is much more accurate than the spring and poppet style, and works much better at lower pressures. Pressure Fermentation Pressure fermentation is becoming more and more popular at the homebrew level, but in order to do it safely and accurately, you need a way to release excess pressure. You'll pressurize your vessel to your desired psi, but once fermentation begins and those hungry, active yeast start creating CO2, the pressure inside the vessel will increase. Attach a spunding valve and set it to your desired pressure, and it will blow off when the pressure gets to high and close up again when it's back to your desired psi. Pressure Transfers Even if you don't have a pressurizable fermenter, you may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process. Diaphragm vs. Poppet With the poppet style spunding valve, a spring pushes against a poppet to keep the valve closed. When the poppet lifts up to open, the surface area the gas pushes against becomes larger, and the spring has to work harder to push the poppet down and reseal the valve. This can lead to more gas being released than intended, and the remaining pressure in your vessel may be at a lower psi than your spunding valve’s set psi.  Instead of a poppet, the spring inside the BlowTie pushes against a diaphragm, which has an immensely larger surface area. This means the surface area that the gas pushes against while the diaphragm is closed is significantly closer to the surface area it pushes against when the diaphragm is open. This leads to higher accuracy, and the remaining pressure after excess gas is released will be much closer to your set blow off pressure. Kit Includes: BlowTie Pressure Gauge (0-40 psi) Ball Lock Disconnect Duotight Tee & Flared Duotight Fitting 2x Lengths of EVABarrier 8mm OD Tubing  

Read more less

Keep the flies away and pesky microbes at bay with these beer faucet brush-style plugs. Made to sit flush when inserted into Intertap, NukaTap and Perlick brand faucets. Easily cleans your faucet spout and can be left in place when the tap is not in use. For the most sanitary seal possible, give the brush a good spray down with sanitizer before plugging the faucet. Comes in 2-pack.

Read more less

Automatically release pressure inside your fermenter during pressure fermentations Regulate beer flow during pressurized transfers from fermenter to keg Built-in pressure gauge for easy reference when adjusting the spunding valve Pressure gauge is interchangeable—swap to different pressure ranges that better suit your application Diaphragm spunding valves offer higher accuracy compared to spring & poppet spunding valves Comes complete with ball lock QD, Duotight adapter, and rigid joiner With this complete kit you'll be ready to use the BlowTie 2 Spunding Valve right out of the box. The BlowTie is used to release excess pressure on a pressurized fermenter or from a receiving keg during pressure transfers. This diaphragm spunding valve is much more accurate than the spring and poppet style, and works much better at lower pressures. This version of the Spunding Valve Kit includes the CM Becker Ball Lock QD, often considered the finest quality in plastic ball lock quick disconnects, and an 8 mm Duotight Flare Adapter for connecting to the BlowTie. The BlowTie 2 can also be upgraded with a Digital Mini Pressure Gauge. Pressure Fermentation Pressure fermentation is becoming more and more popular at the homebrew level, but in order to do it safely and accurately, you need a way to release excess pressure. You'll pressurize your vessel to your desired psi, but once fermentation begins and those hungry, active yeast start creating CO2, the pressure inside the vessel will increase. Attach a spunding valve and set it to your desired pressure, and it will blow off when the pressure gets to high and close up again when it's back to your desired psi. Pressure Transfers Even if you don't have a pressurizable fermenter, you may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process. Diaphragm vs. Poppet With the poppet style spunding valve, a spring pushes against a poppet to keep the valve closed. When the poppet lifts up to open, the surface area the gas pushes against becomes larger, and the spring has to work harder to push the poppet down and reseal the valve. This can lead to more gas being released than intended, and the remaining pressure in your vessel may be at a lower psi than your spunding valve’s set psi. Instead of a poppet, the spring inside the BlowTie pushes against a diaphragm, which has an immensely larger surface area. This means the surface area that the gas pushes against while the diaphragm is closed is significantly closer to the surface area it pushes against when the diaphragm is open. This leads to higher accuracy, and the remaining pressure after excess gas is released will be much closer to your set blow off pressure. Kit Includes: BlowTie 2 w/ Integrated Pressure Gauge (0-15 psi) CM Becker Gray Ball Lock Disconnect Duotight Flare Fitting 8 mm OD Rigid Plastic Joiner

Read more less

This plastic ball lock cap features soda bottle threads, allowing you to convert a 1 or 2 liter soda bottle into a convenient travel growler. The ball lock is compatible with both gas and beverage disconnects, so you can charge the PET bottle before you leave the house and dispense on the go. Attach 3/16" or 1/4" ID tubing to the barb to serve as your dip tube and you're all set! These caps also work great for quickly and conveniently cleaning your draft lines. Mix up a small batch of line cleaning solution in a soda bottle, attach the ball lock cap, and then connect it to your beverage line. Place a bucket below your tap to catch the cleaning solution and open your faucet. Then simply turn the bottle upside down and squeeze it to push solution through your line and out the faucet. You can also choose to pressurize the bottle first, but squeezing the solution through is just as effective. Fermenting with the FermZilla? This is the same ball lock fitting included with the FermZilla Pressure Kit and it's also compatible with the FermZilla Collection Container. If you use the collection container to add dry hops, attach one of these caps and you'll be able purge the container of oxygen before opening the dump valve to introduce the hops. Attach some tubing and diffusion stone and you can oxygenate your wort through the collection container as well! When using two ball lock caps, we recommend pairing this yellow plastic cap with a red plastic cap so you can easily identify which caps are being used for liquid or gas. The barb is Duotight compatible. If you'd like to use the cap with 8 mm OD EVABarrier tubing, see DUO10. For a stainless steel option see KG50. Specs: Liquid and Gas Ball Lock Compatible Overall Length - 2.5" Barb Length - 7/8" Barb OD - 1/4" Barb ID - 3/16" 28mm PCO 1881 Threads Kegland Part number: KL1078

Read more less

Use these high quality, food-grade quick-disconnects on your gas and beer tubing lines. Uses might include the following: * On a gas system to unhook your tank and regulator from your manifold so you take it with you. * On a beer line to easily switch between ball lock, pin-lock, or a commercial tap * On a counter-pressure bottle filler to be able to easily connect to your existing gas line. This plastic quick disconnect set features 1/4" barb which can be used with tubing ID 3/16" through 5/16". The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you need not worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade buna-n.

Read more less

Automatically release pressure inside your fermenter during pressure fermentations Regulate beer flow during pressurized transfers from fermenter to keg Built-in pressure gauge for easy reference when adjusting the spunding valve Pressure gauge is interchangeable—swap to different pressure ranges that better suit your application Diaphragm spunding valves offer higher accuracy compared to spring & poppet spunding valves 8 mm Duotight inlet/outlet for use with 8 mm OD EVABarrier tubing or 8 mm Rigid Joiners The Blow Tie Spunding Valve is used to release excess pressure on a pressurized fermenter or from a receiving keg during pressure transfers. This diaphragm spunding valve is much more accurate than the spring and poppet style, and works much better at lower pressures. The BlowTie 2 features an integrated pressure gauge so you can quickly and easily dial in your pressure setting. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. Pressure Fermentation Pressure fermentation is becoming more and more popular at the homebrew level, but in order to do it safely and accurately you need a way to release excess pressure. You'll pressurize your vessel to your desired psi, but once fermentation begins and those hungry, active yeast start creating CO2, the pressure inside the vessel will increase. Attach a spunding valve and set it to your desired pressure, and it will blow off when the pressure gets too high and close up again when it's back to your desired psi. Pressure Transfers Even if you don't have a pressurizable fermenter, you may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process. Diaphragm vs. Poppet With the poppet style spunding valve, a spring pushes against a poppet to keep the valve closed. When the poppet lifts up to open, the surface area the gas pushes against becomes larger, and the spring has to work harder to push the poppet down and reseal the valve. This can lead to more gas being released than intended, and the remaining pressure in your vessel may be at a lower psi than your spunding valve’s set psi. Instead of a poppet, the spring inside the BlowTie pushes against a diaphragm, which has an immensely larger surface area. This means the surface area that the gas pushes against while the diaphragm is closed is significantly closer to the surface area it pushes against when the diaphragm is open. This leads to higher accuracy, and the remaining pressure after excess gas is released will be much closer to your set blow off pressure. Set Up The BlowTie spunding valve comes with 8 mm Duotight fittings on the inlet and outlet, and we recommend using it with EVABarrier 8 mm OD tubing (D1717 or D1718). You'll also need the flare Duotight fitting (DUO106) in order to attach it to a ball lock or pin lock disconnect. Dialing in your desired pressure is even easier with the BlowTie 2, thanks to the integrated pressure gauge. Simply start with the adjustment knob fully closed, then slowly open it until the gauge reading matches your desired pressure setting. Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends Interchangeable pressure gauge Gauge reads from 0-15 psi WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Kegland Part number: KL15042

Read more less

Get instant pressure reads with the back illuminated Digital Mini Pressure Gauge from KegLand. Swap out the analog pressure gauge on your Core 360 Mini CO2 Regulator, BlowTie 2 Spunding Valve, or Duotight In-Line Regulator. With a 0-90 psi pressure range, the Digital Mini Gauge is suitable for a wide range of applications. KegLand has developed the world's most compact mini digital gauge with backlight illumination. This very compact design retains high accuracy while still meeting the desirable small form factor. This meets the growing need as mini keg systems, mini regulators and other more compact keg dispensing solutions are required. Traditional analog gauges require a small capillary mechanism where a small pipe expands and unravels under pressure. This in turn drives a mechanical cog to rotate the gauge needle. This age-old technique works quite well especially in large gauges but as this mechanism is manufactured smaller and smaller a tradeoff between accuracy and size becomes the issue. With very small gauges such as a 27mm x 27mm Mini Gauge, it's difficult to make them better than 10% accuracy due to the physical constraints of the mechanical components. Compatible With: BlowTie 2 Spunding Valve Duotight In-Line Regulator w/ Gauge Core 360 Mini CO2 Regulator Specifications: Backlight Illumination: Hold yellow button for 3-5 seconds Battery Life: More than 2 years (using the mini gauge once a day) Battery Type: CR2032 Auto Battery Saver: automatically turns off after 15 sec Size: 27mm x 27mm (1" x 1") Radial O-ring Stem: 7.8mm Bore KegLand Part Number: KL1838 Please note: This gauge is not suitable for measuring pressure of liquids. It is only for measuring gas pressure. If liquid gets into the pressure transducer it will damage the gauge. For analog pressure gauges that are compatible with liquid, see below: Mini Gauge 0-15psi Mini Gauge 0-30psi Mini Gauge 0-60psi Mini Gauge 0-150psi KegLand Part Number: KL1838

Read more less

Automatically release pressure inside your fermenter during pressure fermentations Regulate beer flow during pressurized transfers from fermenter to keg Built-in pressure gauge for easy reference when adjusting the spunding valve Pressure gauge is interchangeable—swap to different pressure ranges that better suit your application Diaphragm spunding valves offer higher accuracy compared to spring & poppet spunding valves Comes complete with Duotight ball lock QD and rigid joiner With this complete kit you'll be ready to use the BlowTie 2 Spunding Valve right out of the box. The BlowTie is used to release excess pressure on a pressurized fermenter or from a receiving keg during pressure transfers. This diaphragm spunding valve is much more accurate than the spring and poppet style, and works much better at lower pressures. This version of the Spunding Valve Kit includes the Duotight Ball Lock QD which allows you to attach the BlowTie directly to the QD via the 8 mm rigid joiner. The BlowTie 2 can also be upgraded with a Digital Mini Pressure Gauge. Pressure Fermentation Pressure fermentation is becoming more and more popular at the homebrew level, but in order to do it safely and accurately, you need a way to release excess pressure. You'll pressurize your vessel to your desired psi, but once fermentation begins and those hungry, active yeast start creating CO2, the pressure inside the vessel will increase. Attach a spunding valve and set it to your desired pressure, and it will blow off when the pressure gets to high and close up again when it's back to your desired psi. Pressure Transfers Even if you don't have a pressurizable fermenter, you may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process. Diaphragm vs. Poppet With the poppet style spunding valve, a spring pushes against a poppet to keep the valve closed. When the poppet lifts up to open, the surface area the gas pushes against becomes larger, and the spring has to work harder to push the poppet down and reseal the valve. This can lead to more gas being released than intended, and the remaining pressure in your vessel may be at a lower psi than your spunding valve’s set psi. Instead of a poppet, the spring inside the BlowTie pushes against a diaphragm, which has an immensely larger surface area. This means the surface area that the gas pushes against while the diaphragm is closed is significantly closer to the surface area it pushes against when the diaphragm is open. This leads to higher accuracy, and the remaining pressure after excess gas is released will be much closer to your set blow off pressure. Kit Includes: BlowTie 2 w/ Integrated Pressure Gauge (0-15 psi) 8 mm Duotight Gray Ball Lock Disconnect 8 mm OD Rigid Plastic Joiner

Read more less

The Push-In Pressure Gauge is the ideal companion for the BlowTie spunding valve (FE960). It comes with an 8 mm (5/16 in.) barb, specifically designed to be compatible with 8 mm Duotight fittings. By pairing this pressure gauge with the BlowTie, you'll be able to easily set your blow off pressure when using the BlowTie for pressure fermentations or pressure transfers. The dial face is triple-scaled to read in psi, bar, and kPa. 8 mm (5/16") push-in barb Rubber coated to protect gauge 0-40 psi / 0-2.5 bar / 0-250 kPa Kegland Part number: KL07696

Read more less

Keep fruit flies and spiders out of your draft beer faucet with this handy plug brush. Plugs your faucet when you are not using it. Attached brush cleans faucet on the way in and out. We like to spray the brush moist with Alpet Spray Sanitizer for the most sanitary seal possible. Note: Does not sit flush on Intertap, NukaTap or Perlick faucets

Read more less

Automatically release pressure inside your fermenter during pressure fermentations Regulate beer flow during pressurized transfers from fermenter to keg Diaphragm spunding valves offer higher accuracy compared to spring & poppet spunding valves 8 mm Duotight inlet/outlet for use with 8 mm OD EVABarrier tubing or 8 mm Rigid Joiners The Blow Tie Spunding Valve is used to release excess pressure on a pressurized fermenter or from a receiving keg during pressure transfers. This diaphragm spunding valve is much more accurate than the spring and poppet style, and works much better at lower pressures. Pressure Fermentation Pressure fermentation is becoming more and more popular at the homebrew level, but in order to do it safely and accurately you need a way to release excess pressure. You'll pressurize your vessel to your desired psi, but once fermentation begins and those hungry, active yeast start creating CO2, the pressure inside the vessel will increase. Attach a spunding valve and set it to your desired pressure, and it will blow off when the pressure gets too high and close up again when it's back to your desired psi. Pressure Transfers Even if you don't have a pressurizable fermenter, you may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process. Diaphragm vs. Poppet With the poppet style spunding valve, a spring pushes against a poppet to keep the valve closed. When the poppet lifts up to open, the surface area the gas pushes against becomes larger, and the spring has to work harder to push the poppet down and reseal the valve. This can lead to more gas being released than intended, and the remaining pressure in your vessel may be at a lower psi than your spunding valve’s set psi. Instead of a poppet, the spring inside the BlowTie pushes against a diaphragm, which has an immensely larger surface area. This means the surface area that the gas pushes against while the diaphragm is closed is significantly closer to the surface area it pushes against when the diaphragm is open. This leads to higher accuracy, and the remaining pressure after excess gas is released will be much closer to your set blow off pressure. Set Up The BlowTie spunding valve comes with 8 mm Duotight fittings on the inlet and outlet, and we recommend using it with EVABarrier 8 mm OD tubing (D1717 or D1718). You'll also need the flare Duotight fitting (DUO106) in order to attach it to a ball lock or pin lock disconnect. Dialing in your desired pressure is very simple. Although you would ideally use the BlowTie with the Push-In Pressure Gauge (D1160) and Duotight Tee Fitting (DUO109), as seen in the example photo, you can easily set the blow off pressure without it. To do this, simply pressurize an empty keg to your desired psi using your CO2 regulator. Before attaching the BlowTie to the gas post, be sure to turn the dial clockwise until it is fully closed. Once attached, slowly turn the dial counterclockwise until gas starts coming out, then slightly turn the dial back to stop the gas flow. The BlowTie is now set to your desired pressure. Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends 0-40 psi pressure rating Please note: the BlowTie does not come with the pictured accessories. Please see "You Might Also Need" below for the other products shown in the example photo. Kegland Part number: KL03643

Read more less

This is the same shank that is used in our D1245A, but without the nipple and hex nut. This gives you the freedom to choose the size and style of tailpiece that fits your needs, as well as the type of hex nut and shank collar you prefer. Check below for available tailpieces. Be sure to add a gasket to use with your chosen tailpiece and hex nut. Dimensions: 4-1/8" - Shank Length 3" - Thread Length 2-3/4" - Pass Through Length

Read more less

Mark’s Mark II Keg Washer™ is designed to clean and sanitize large vessels like cornelius kegs and carboys. This keg cleaner is also intended to provide a sanitation container for miscellaneous items such as airlocks, thermometers, tubing, keg fittings, and more. Quiet, Fun, & Easy to Use Very quiet when in use and most importantly speeds up the process of cleaning and sanitizing.    Light in weight.  Easy to store.  Cleans Kegs This keg washer cleans and sanitizes a cornelius keg without having to take apart the ball lock fittings, poppets, and dip tubes. You can clean the keg and the dip tube simultaneously using the T adapter. Cleans Tubing Too Cleans tube separately utilizing the pump with the additional barb fittings included.  Cleans Parts Reservoir holds 1.25 gallons of water making it easy to fill and empty with sanitizer.     Saves water and sanitizer.  The keg washer does not have an on/off switch, you can plug it directly into a wall outlet to operate the pump or plug it into an outlet that is controlled by a switch. Never leave the keg washer unattended when in use. When in use, fill the keg washer up to about 1 inch under the brim. The pump is not self priming, so always make sure the basin is full of water before plugging in the pump. Owner's Manual is included. Please read thoroughly before using. Dimensions of the inside of the washer's reservoir are: 6"L x 12"W x 4"D. Please Note: Product does not include the bucket, carboy, or keg pictured above for display purposes. The pump specs are: 520 GPH 120 Volts AC 40 watts Ceramic shaft, impeller  

Read more less

A must-have tool for any DIY draft-cleaning system, the Faucet Cleaning Adapter makes it a cinch to back-flush your draft lines for cleaning. Simply remove your draft faucet and mount the adapter in its place, leaving you with a 3/8” barb to connect tubing.   Made from brass.

Read more less

This Duotight Bulkhead is the same one used for installing the Temp Twister cooling coil into the lid of the FermZilla. Allows you to add a bulkhead to just about anything that can then be connected to with EVABarrier 9.5 mm OD Tubing (D1719) or 3/8" OD stainless or copper tubing. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL14564

Read more less

These quick disconnects feature 1/4" barbed fittings which can be used with either 3/16", 1/4" or 5/16" line. The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you need not worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade buna-n. For the female side, see our H550B.

Read more less

Give yourself peace of mind with this Reinforced Vinyl Brewing Tubing! This 1/2" Reinforced Vinyl Tubing is FDA approved, food grade, rated to 158 degrees F, and 200 PSI. It is the perfect tubing to use in your homebrewery with our pumps, or anywhere you want the extra security that your tubing will not kink or burst. This type of tubing is essential when putting back pressure on a system. Standard vinyl tubing and silicone are great for their own purposes, but are not designed to handle pressure, and can balloon up or explode if too much pressure is used. 1/2" ID and 3/4" OD  

Read more less

This Duotight reducer fitting can be attached to the Intertap Short Shank with 1/4" Duotight compatible barb (D1242). Compatible with EVABarrier 9.5 mm OD tubing (D1719). Also attaches to the Plastic Ball Lock Cap, allowing the cap to be used with 9.5 mm OD EVABarrier. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL08648

Read more less

This Duotight to 1/2" female thread fitting can be used to connect beverage or gas line to fittings with 1/2" male threading. Compatible with EVABarrier 9.5 mm OD Tubing (D1719). Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL13871  

Read more less

Everything that comes with our Premium kit plus our Kegging Starter Kit Skip the bottling process and serve your very first home brewed beer on draft! Includes the best-selling 5-gallon Torpedo Keg — a huge upgrade over standard ball lock Cornelius kegs Brand new 5 lb CO2 cylinder can be filled at your local homebrew shop or welding supply store Step-by-Step instructions included for both brewing and kegging/carbonating your finished beer Why dip your toes in the water when you can take a running start and cannonball right into the world of homebrewing? With the Premium Homebrew and Kegging Starter Kit you can skip the bottling-induced headaches and go straight to kegging your first batch. Get everything included in two of our most popular kits at an even better value! Starting with the brewing equipment, you'll receive everything that comes with our top-shelf Premium Homebrew Starter kit (BRKIT30). This includes a massive 8.5 gallon stainless steel brewing kettle, 7 gallon Fermonster fermenter, copper wort chiller, American Pale Ale ingredient kit, and all the time tested brewing equipment you need to make beer at home. The large volume kettle allows for Full-Boil brews, which can have lighter color and better hop flavors. No need to fuss with a funnel or siphon thanks to the included kettle spigot, which can be used to safely and easily transfer liquid from your kettle to your Fermonster fermenter. The Fermonster is the perfect vessel for your first batch, and the 7 gallon capacity means you won't have to upgrade down the road when you want to brew beer styles that foam a lot during fermentation. Several of the most popular upgrades for new homebrewers include a larger kettle, a larger fermenter, and a wort chiller. With this kit you can check off those boxes on Day 1! Brewing is a labor of love. But few love the labor of bottling their finished brew. Luckily for you, everything from the 5 gallon Torpedo Homebrew Kegging kit (KEG410) is also included. When your brew buddies swap bottling horror stories, just listen and nod your head politely. We won't tell anyone that you skipped the bottling stage entirely! This system is comprised of absolutely everything you need to dispense your homebrew on draft. The dual gauge regulator will tell you the pressure in the keg, as well as how much CO2 is left in the tank. Comes with an aluminum CO2 tank that will never rust. 5 feet of 3/16" ID beer line, ideal for draft systems, so your beer drops to the correct pressure and does not excessively foam in the glass. Last but not least, this system features the 5 gallon Torpedo Keg, an all stainless ball lock keg with a commercial style. These kegs are stackable and feature rolled handles that make transport a breeze. The Fermonster Fermenter - A Huge Upgrade Over Standard Buckets or Glass "Carboy" Water Bottles Unlike buckets or glass carboys, the Fermonster fermenter was designed for brewing beer. It is made from tough, clear, virgin grade PET plastic so you can see the magic of fermentation. Unlike glass it will never break and shatter if dropped. It represents a huge upgrade over traditional buckets because these fermenters are much less likely to get scratched. Scratches can hold bacteria that can cause off flavors in the beer. The Fermonster comes with a built-in spigot that eliminates a long time issue in homebrewing of having to start a siphon to transfer your beer to the bottling bucket after fermentation is over. The large 4" lid allows for easily adding yeast, hops, or other additions. We also really love the molded-in level markers that tell you exactly when you have reached your desired volume. We Don't Skimp on Cleaning and Sanitizing Proper cleaning and sanitizing is one of the core tenants of making great beer. Some starter kits utilize an all-in-one cleaner/sanitizer that does neither job well. We’ve included the best-selling sanitizer for brewing, Star San. We also include Craftmeister oxygen-based cleaning tablets that make cleaning your Fermonster Fermenter a breeze. Other Upgrades That Make Brewing Easier We’ve also made a few items standard that really make the brew day easier including a thermometer for temperature monitoring and a hydrometer with testing jar for measuring sugar levels. Our reusable mesh bags allow for the easy removal of spent grain and hops at the end of the boil. The included stainless spoon is a really nice upgrade over plastic when you are stirring boiling liquids. Easy, How-To Instructions & an Actual 800# We've taught hundreds of thousands of people how to brew in over 25 years. Our instructions are clear and simple to follow and will have you making great beer with batch number one. If you have any questions, call our on-staff brewmasters at 1-800-600-0033. In an age where 800-numbers and real customer service is going away, you can still call us and ask a question. Brewing Equipment Included: 7 Gallon Fermonster fermenter with built in spigot, stopper, and airlock 8.5 Gallon Stainless Steel Brew Kettle w/ thermometer port, stainless ball valve, internal volume markers, Silicone handle grips Copper Wort Chiller for quick cooling Food Grade Bucket for bottling Mesh bags for grain and hops on brew day A Thermometer for easy temperature management Hydrometer for making key sugar measurements Transfer Tubing Bottling Wand with shut off valve Sturdy Bottle Capper Bottle Caps Bottle Cleaning Brush Star San Sanitizer for true sanitizing Large Stainless Steel Spoon for mixing Craftmeister Cleaning Tablets for super easy cleaning Delicious American Pale Ale recipe kit with yeast Kegging Equipment Included: Brand New 5 Gallon Torpedo Ball Lock HomeBrew Keg Beer line assembly with hand held faucet New Aluminum 5 lb CO2 tank Gas line assembly Premium Dual Gauge regulator The CO2 tank is shipped empty. You can have it filled at a welding supply shop or see your Yellow Pages under Gas- Industrial, Medical.

Read more less

Perfect for spraying down brewing equipment with dissolved cleaners or sanitizers Attach the optional Ball Lock Keg Post Adapter to convert the sprayer into a line cleaning device Empty the large 33.8 oz tank up to 30 times on a single charge The Power Sprayer is a fantastic multi-purpose device that can be used for spraying down your brewing equipment with cleaners and sanitizers or converted into a pressurized line cleaning system. The tank features graduated volume markers and can be emptied up to 30 times on a single charge. The nozzle knob can be adjusted to turn the stream into a fine mist or a powerful jet. This product is made from food grade Santoprene, PP, PE, Silicone and stainless components. Battery Life The pump has large 18650 li-ion rechargeable battery. On a full charge the battery will empty the tank 18-30 times so it lasts for ages. If you use fine mist it will be closer to 18 times but if you use a jet/stream the battery will last closer to 30 times. Includes: 33.8 oz Reservoir Tank Power Sprayer Nozzle and Dip Tube White Plastic Adjustment Head Sprayer 6" USB-C to Standard USB Cable *Does not include USB wall charger KegLand Part Number: KL40860

Read more less

O Ring for Beer & Gas Line QD (for H550A)

Read more less

The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required. Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing. 6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length. Duotight Push-to-Connect These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done! Compact The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines. Overmolded Poppet The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out. Tool-less Disassembly Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects. Extreme Chemical Resistance No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing. Toughness This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough! High Flow The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects. Features: Ball Lock Quick Disconnect - Gas In Direct connect EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Disassemble by hand for quick and easy cleaning Three sizes available: 6.35 mm (KL24242) 8 mm (KL20756) 9.5 mm (KL20770)

Read more less

The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required. Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing. 6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length. Duotight Push-to-Connect These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done! Compact The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines. Overmolded Poppet The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out. Tool-less Disassembly Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects. Extreme Chemical Resistance No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing. Toughness This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough! High Flow The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects. Features: Ball Lock Quick Disconnect - Bev Out Direct connect EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Dissamble by hand for quick and easy cleaning Three sizes available: 6.35 mm (KL24235) 8 mm (KL20749) 9.5 mm (KL20763)

Read more less

Converts the KegLand Power Sprayer into a compact, convenient line cleaning device Ball Lock multi-post is compatible with both Gas & Liquid QDs Attach the Ball lock Keg Post Adapter to the KegLand Power Sprayer to turn the unit into a convenient line cleaning device. The multi-post is compatible with both Gas & Liquid ball lock quick disconnects. This part is only suitable for the Power Sprayer. It is not a standard thread size. It has been custom made for this product and this product only.   Please Note: The keg post adapter does not include a spring & poppet. This is intentional in order to prevent the flow path from being blocked if the sprayer was unintentionally powered on without a ball lock disconnect connected to the post. Powering the sprayer with the flow path blocked could damage the pump. KegLand Part Number: KL42871

Read more less

Savvy homebrewers love quick disconnects on their gas lines! They give you the ability to quickly move hoses from one configuration to another with ease! These quick disconnects feature 1/4" barbed fittings which can be used with 3/16", 1/4" or 5/16" line. The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you don’t need to worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade Buna-N. In short, these QDs are durable, user friendly and versatile. A no-brainer! For the male side, see our H550A, or buy both sides together as a set.

Read more less

Get instant pressure reads with the back illuminated Digital Mini Pressure Gauge from KegLand. Compatible with 8 mm Duotight fittings and Gray Ball Lock QDs. If you're using the original BlowTie spunding valve without pressure gauge, you can use a Duotight tee fitting in-line between the ball lock QD and the BlowTie to take pressure readings with the Digital Mini Gauge. KegLand has developed the world's most compact mini digital gauge with backlight illumination. This very compact design retains high accuracy while still meeting the desirable small form factor. This meets the growing need as mini keg systems, mini regulators and other more compact keg dispensing solutions are required. Traditional analogue gauges require a small capillary mechanism where a small pipe expands and unravels under pressure. This in turn drives a mechanical cog to rotate the gauge needle. This age-old technique works quite well especially in large gauges but as this mechanism is manufactured smaller and smaller a tradeoff between accuracy and size becomes the issue. With very small gauges such as a 27mm x 27mm Mini Gauge, it's difficult to make them better than 10% accuracy due to the physical constraints of the mechanical components. Specifications: Battery Life: More than 2 years (using the mini gauge once a day) Battery Type: CR2032 Auto Battery Saver: automatically turns off after 15 sec Size: 27mm x 27mm (1" x 1") Duotight Stem: 8 mm KegLand Part Number: KL18081 Please note: This gauge is not suitable for measuring pressure of liquids. It is only for measuring gas pressure. If liquid gets into the pressure transducer it will damage the gauge.

Read more less

If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 4 mm (5/32") ID size is perfect for homebrew draft applications where only a short beer line is needed. We recommend using 5-6 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 4 mm (5/32") Outer Diameter - 8 mm (5/16") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. Kegland Part number: KL06224

Read more less

Made with a fully stainless steel sanke coupler with ball valves at both ends. The check valves have been removed so solution can be back flushed through the system. Perfect for washing or filling Sanke D kegs. This is the same coupler featured on the MoreBeer! Pro Manual Keg Filler. 1/2" tailpieces at inlet and outlet.

Read more less

This non-caustic cleaning powder will make quick work of any stubborn soil build-up on your brewing equipment. TLC will help you brew your best beer possible by keeping your home brewery in tip-top condition. TLC is an efficacy proven alternative to caustic cleaners. Why You'll Love TLC: Versatile – TLC is a versatile cleaner and allows for both soak and low foam circulation cleaning. This product works at all temperatures. Effective – TLC is effective at removing the toughest caked on debris without scrubbing. It is non-corrosive and safe to use on soft metals. Safe – This product is safe on skin, and has no noxious fumes, while maintaining the effectiveness of heavy-duty caustic cleaners. Economical – TLC is an easy to use and economical choice for tank and line cleaning. Product Highlights: Non-caustic formula Great for circulation cleaning or parts soaking Effective at removing organic soils such as fats, greases, proteins, and yeast Effective at a wide temperature range Safe on soft metals Economical dilution Non-corrosive with the performance of a caustic cleaner Convenient pack sizes Oxygen booster for alkaline cleaning solutions Skin contact safe Gentle on rubber seals and gaskets  

Read more less

Reinforced vinyl tubing is a great option for transferring your homebrewed beer. This food grade 3/8 in ID Reinforced Vinyl Tubing is rated to 158 degrees F, and 40 PSI. Use this tubing anywhere you want the extra security that your tubing will not kink, or burst. This type of tubing is useful in your setup where you want extra tubing strength, but your system pressure won't exceed 250 psi.  

Read more less

This Duotight fitting with 1/4" Flare is perfect for flared gas and beverage ball lock and pin lock disconnects. It can also be used to connect gas line to the flare fitting found on the KOMOS® CO2 Regulator. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). The Duotight fitting does not require a flare washer. See the instructions below for how to ensure a leak-free connection when attaching to flare fittings. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Ball lock fitting and regulator not included. Kegland Part number: KL06880

Read more less

PetroGel is used as a food grade lubricant in kegging systems, and other beer and wine applications. It can be used to lubricate o-rings, and can "rejuvenate" worn o-rings on keg lids and other areas. The petroleum lubricant can get sticky and hold on to soils. For a non-sticky alternative, some people prefer the silicone spray lubricant (CH238).

Read more less