Draft
Shop by collection
-
Rigid Plastic Joiner for Duotight Fittings | 8 mm
Creates perfectly straight, rigid joins with push-in fittings Simplifies connecting small accessories compared to using EVABarrier tubing 44mm length provides ample grip and easy disassembly, even after full insertion into two Duotight 8mm fittings This rigid joiner is made from strong polypropylene. It's useful to make rigid joins with push-in fittings that are dead straight. Although it's possible to make joins using short pieces of 8mm OD EVABarrier tubing, when mounting parts to a gas board or wall it will often make things much neater if you use these instead. The 44mm length is long enough so even after pushing right into two Duotight 8mm fittings on both ends, you should still have an exposed length of about 3mm so you can still easily take the fittings apart later. 8mm OD x 44mm L (5/16" x 1.7"). Available in singles or 10-packs. KegLand Part Number: KL18012
$0.99 - $4.39
-
Duotight In-Line Regulator | Built-In Pressure Gauge | 0-60 PSI | Liquid & Gas Compatible | 8 mm Duotight
Easily set and view different pressures downstream from a single CO2 regulator. Serve different beverages at different pressures without the need for expensive regulator manifolds! Built-in pressure gauge for easy reference when adjusting pressure settings Pressure gauge is interchangeable—swap to different pressure ranges that better suit your application Compatible with both liquid and gas 8 mm Duotight inlet/outlet for use with 8 mm OD EVABarrier tubing or 8 mm Rigid Joiners The Duotight In-Line Regulator is an ideal solution if you want to serve different beers at different gas pressures. In a typical multiple line, multiple pressure system you would run a gas line from your main regulator into a secondary regulator where you would set different pressures. While that is ideal, it is a little pricey. This little sweetheart lets you set different pressures at a far lower cost. What we do is set the main regulator at the highest pressure we want in the system - for example a keg of soda that you want to carbonate and serve at 25 psi. Run the gas line into a manifold and then install one of these after the manifold on each line where you want to decrease the pressure, for example lowering to 10psi to serve your British pale ale and 14 psi to serve your summertime lawnmower lager. Works with both gas and liquid. Easily adjust the flow can be adjusted with the yellow adjustment knob. 8 mm Duotight fittings at both inlet and outlet make this unit perfect for use with EVABarrier 8 mm OD tubing (D1717 or D1718). Features an integrated pressure gauge so you can quickly and easily dial in your pressure setting. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. Stepping Down Pressure The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability. Ideal regulation scenario (10 PSI less than inlet pressure) Example of 30 PSI inlet translating to 0–20 PSI output Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends Interchangeable pressure gauge Gauge reads from 0-60 psi Made with quality EPDM seals Wall mountable WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Kegland Part number: KL15035
$19.49
-
Duotight Push-In Fitting - 8 mm (5/16 in.) Plug
This Duotight plug is used to block up your 8 mm (5/16") tees, elbows or other fittings for gas leak testing or simply to plug an unused section. Features: Insert plug and firmly push to connect Release plug by pushing in the collet on the Duotight fitting Suitable for both gas & beverage applications Made from food-grade acetal plastic Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number KL06958
$1.69
-
Beer & Gas Tubing Quick Disconnect (QD) - 3/8" Barb x Female Shut-off
Savvy homebrewers love quick disconnects on their gas lines! They give you the ability to quickly move hoses from one configuration to another with ease! These quick disconnects feature 3/8" barbed fittings which can be used with 5/16", 3/8" or 7/16" line. The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you don’t need to worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade Buna-N. In short, these QDs are durable, user friendly and versatile. A no-brainer! This is a direct replacement to the Female Quick Disconnect with 3/8" Barbs that is featured on the BrewBuilt CoolStix™.
$10.99
-
Retaining Circlip for Duotight Push-In Fittings - Pack of 10 - 8 mm (5/16 in.)
Duotight 8 mm OD retaining clip. Locks Duotight fittings in their closed position, making it impossible for any hose to escape. Pack of 10. KegLand Part Number: KL21517
$4.39
-
The Carboy Cleaner - Replacement Pads
You love your Carboy Cleaner so much that you’ve worn out the cleaning pads! A set of replacement pads and washers for The Carboy Cleaner™. The ease and convenience of the Carboy Cleaner can’t be overstated. After you’ve used it to clean enough carboys and kegs, you will need to replace the cleaning pads. Set of 2 replacement pads and 4 washers for The Carboy Cleaner™.
$13.99
-
Push-In Pressure Gauge (0-15 psi)
The Push-In Pressure Gauge is the ideal companion for the BlowTie spunding valve (FE960). It comes with an 8 mm (5/16 in.) barb, specifically designed to be compatible with 8 mm Duotight fittings. By pairing this pressure gauge with the BlowTie, you'll be able to easily set your blow off pressure when using the BlowTie for pressure fermentations or pressure transfers. The dial face is triple-scaled to read in psi, bar, and kPa. 8 mm (5/16") push-in barb Rubber coated to protect gauge 0-15 psi / 0-1.0 bar / 0-100 kPa Kegland Part number: KL14186
$9.89
-
EVABarrier Double Wall Draft Tubing | Transparent Red | 5 mm ID x 8 mm OD
Easily identify gas and beverage lines with color-coded options—LightShield Black for beverages, Transparent Red for gas EVABarrier's double-walled design with a proprietary inner polymer significantly reduces oxidation and CO2 loss, keeping your beer fresher for longer The ultra-smooth, nearly impermeable inner surface of the tubing prevents bacteria and microbes from adhering, ensuring cleaner beer lines The stiff yet pliable EVA outer barrier makes the tubing kink-resistant and ideal for use with push-in fittings like Duotight and John Guest Red is recommended for differentiating your gas lines, but the 5mm ID is the perfect size if longer 10-12 ft. beverage lines are needed Easily identify your gas and beverage lines with color-coded draft tubing. Transparent Red EVABarrier is recommended for gas lines while using LightShield Black for your bev lines, saving you a headache when your draft lines inevitably get tangled up in your draft system. The semi-transparent red outer barrier makes the tubing easy to recognize even with minimal light. If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. If you wish to use the tubing for beverage rather than gas, we recommend using 10-12 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 5 mm (13/64") Outer Diameter - 8 mm (5/16") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. KegLand Part Number: KL42741
$28.49 - $120.89
-
NukaTap® Stainless Steel Beer Faucet | Flow Control Gen 2 | Forward Sealing
G2 model features redesigned flow control mechanism for improved shank sealing and flow control Make instant adjustments to beverage flow as you pour Switch from pouring pints to filling growlers without adjusting your CO2 regulator Reduced first pour foam due to low thermal mass Forward-sealing design prevents beer residue from gumming up the faucet Unique shuttle design greatly improves laminar flow, improving the pour of carbonated beverages Compatible with all Intertap faucet accessories and shanks Generation 2 The NukaTap Flow Control G2 uses a completely new flow control mechanism with better sealing properties against the shank as well as improved flow control. Control the Flow The flow control model is a great option for users that often switch between beer styles with different carbonation levels. No need to rebalance your lines or play with your regulator settings. Instantly make adjustments as you pour to dial in the flow rate. This is also a super convenient feature for when you want to grab a quick growler on your way out. By dialing back the flow rate, you can gently fill your growler so CO2 stays in solution and your beer doesn't pour flat when it comes time to share. The NukaTap Flow Control faucet is also the first FC model to be fully compatible with the optional self-closing spring. First Pour Foam Reduction Every kegerator owner knows the letdown of pouring your first pint of the day and getting too much foam. Even with perfectly balanced draft lines, first pour foam is sometimes unavoidable simply due to the temperature of the faucet itself. Running beer through the faucet will drop the temperature, and the foaming will subside, but not without a bit of wasted beer from pouring off excess head. The NukaTap beer faucet drops to beer serving temperature much faster thanks to its lower thermal mass. Simply put, the bulkier the faucet is, the more beer is needed to flow through and chill the tap. The NukaTap is over 20% lighter than its Intertap predecessor, and even lighter still compared to other brands of faucets. Improved Laminar Flow The inspiration for the NukaTap name comes from its uniquely designed "nuke-shaped" shuttle that resides on the inside of the faucet. The NukaShuttle went through numerous rounds of redesigns and countless hours of testing to find a shape that provides superior laminar flow. This means that liquid passes by the shuttle with very little resistance, allowing highly carbonated beers or hard seltzers to pour like a dream. Sanitary Design The NukaShuttle is the world’s first seamless single-piece design. Traditional taps feature an o-ring seated on a stainless steel shuttle, which can cause a couple of issues. After many pours, the stainless shuttle rubbing against the internal body of the faucet will create small fissures that become potential infection sites, and the seated o-ring can be difficult to clean in place, making your draft cleaning and sanitizing process less effective than you realize. The NukaShuttle is an advanced TPV rubber matrix that has been seamlessly formed over a durable PP skeleton. This single-piece design eliminates the pitfalls of older manufacturing methods, making it one of the most sanitary faucets on the market. Forward Sealing vs. Rear Sealing From tap rooms to home bars, forward-sealing faucets are the ideal choice for any draft setup. In traditional rear-sealing taps, beer will drain out of the entire faucet when it's in the closed position. This means the internal mechanism is coated in beer, which then dries and becomes a sticky residue. Forward-sealing faucets, on the other hand, keep the tap full of beer so it never has a chance to dry and gunk up the internal parts. This makes the faucet much easier to clean and also reduces the chance of off flavors transferring to your beer while you pour. Made from stainless steel Shuttle made from TPV O-rings made from EPDM Kegland Part Number: KL15523
$59.99
-
Duotight Push-In Fitting - 8 mm (5/16 in.) x 1/4 in. BSP
This Duotight fitting with 1/4" male thread is a great option for connecting gas line to regulators and manifolds that have 1/4" FPT. Comes with seated O-ring. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL06897
$3.29
-
Ultra Barrier™ PVC Free Beer Tubing - 3/16 in.
Due to high demand, some of these items are currently out of stock but available for pre-order. Please check status notes below when selecting a size option to see if it is In Stock or tagged as PreBook. We will automatically ship this to you when we receive more inventory. Commercial quality beer tubing is now available for the homebrewer! EJ Beverage Ultra Barrier™ tubing from EJ Beverage is constructed of a unique compound that provides for an excellent alternative to PVC. Advantages to this unique tubing are: PVC Free and BPA Free - containes no DEHP phthalates or other plasticizers Environmentally friendly production - does not emit dioxins Proven to have no significant impact on taste or flavor Extremely low extractables/leachables High flexibility Remains flexible at lower temperatures Ultra-low permeability Superior Barrier properties Temperature range of -40 to 125° F Working pressure of 88 psi 3/16" is the best size for most beer lines under 9' in length. Ideally, 6' provides the correct restriction for serving beer in the 10-14 psi range. Technical Specifications: 3/16" line provides 2.2 lbs of restriction per foot. Ideally pounds of resistance should equal pounds of applied pressure. 3/16" line holds 1/6 of an ounce per foot. PVC Free. 7/16" OD
$9.49 - $123.99
-
EVABarrier Double Wall Draft Tubing - 6.3 mm ID x 9.5 mm OD
If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 6.3 mm (1/4") ID size is recommended to be used as gas line or long draw beverage lines. If you intend to use it as beverage line, we recommend using 20-25 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 6.3 mm (1/4") Outer Diameter - 9.5 mm (3/8") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. Kegland Part number: KL06248
$6.10 - $142.34
-
KOMOS® Draft Multi Tool with Duotight Remover | Multi Purpose Beer Faucet & Shank Wrench | 7 in 1 Draft System Tool
The KOMOS multi tool is a convenient instrument to keep nearby that is suitable for most of the fittings you'll encounter when setting up or making adjustments to your kegerator or keezer. If you're kegging your brew then you're well acquainted with the many nuts, bolts, and clamps it takes to rig up a draft system. Even small adjustments will often have you walking back and forth from the tool box before the job done. The KOMOS draft tool offers 7 unique functions for tasks including faucet collar adjustments, shank hex nut adjustments, connecting or disconnecting a CO2 regulator and tank, removing Duotight fittings, and, most importantly, removing bottle caps from beer bottles. The KOMOS multi tool is suitable for most connection adjustments, but if you're adjusting a CO2 regulator nut that has been overtightened, we recommend using a standard Crescent wrench for extra torque. Functions: CO2 Regulator Nut Spanner Shank Hex Nut Spanner Faucet Coupling Ring Pin Wrench Flare Swivel Nut Spanner 8 mm Duotight Removal 9.5 mm Duotight Removal Bottle Opener Made of stainless steal.
$5.49
-
NukaTap® Stainless Steel Beer Faucet | Forward Sealing
Newest faucet design on the market! Reduced first pour foam due to low thermal mass Forward-sealing design prevents beer residue from gumming up the faucet Unique shuttle design greatly improves laminar flow, improving the pour of carbonated beverages Compatible with all Intertap faucet accessories and shanks First Pour Foam Reduction Every kegerator owner knows the letdown of pouring your first pint of the day and getting too much foam. Even with perfectly balanced draft lines, first pour foam is sometimes unavoidable simply due to the temperature of the faucet itself. Running beer through the faucet will drop the temperature, and the foaming will subside, but not without a bit of wasted beer from pouring off excess head. The NukaTap beer faucet drops to beer serving temperature much faster thanks to its lower thermal mass. Simply put, the bulkier the faucet is, the more beer is needed to flow through and chill the tap. The NukaTap is over 20% lighter than its Intertap predecessor, and even lighter still compared to other brands of faucets. Improved Laminar Flow The inspiration for the NukaTap name comes from its uniquely designed "nuke-shaped" shuttle that resides on the inside of the faucet. The NukaShuttle went through numerous rounds of redesigns and countless hours of testing to find a shape that provides superior laminar flow. This means that liquid passes by the shuttle with very little resistance, allowing highly carbonated beers or hard seltzers to pour like a dream. Sanitary Design The NukaShuttle is the world’s first seamless single-piece design. Traditional taps feature an o-ring seated on a stainless steel shuttle, which can cause a couple of issues. After many pours, the stainless shuttle rubbing against the internal body of the faucet will create small fissures that become potential infection sites, and the seated o-ring can be difficult to clean in place, making your draft cleaning and sanitizing process less effective than you realize. The NukaShuttle is an advanced TPV rubber matrix that has been seamlessly formed over a durable PP skeleton. This single-piece design eliminates the pitfalls of older manufacturing methods, making it one of the most sanitary faucets on the market. Forward Sealing vs. Rear Sealing From tap rooms to home bars, forward-sealing faucets are the ideal choice for any draft setup. In traditional rear-sealing taps, beer will drain out of the entire faucet when it's in the closed position. This means the internal mechanism is coated in beer, which then dries and becomes a sticky residue. Forward-sealing faucets, on the other hand, keep the tap full of beer so it never has a chance to dry and gunk up the internal parts. This makes the faucet much easier to clean and also reduces the chance of off flavors transferring to your beer while you pour. Made from stainless steel Shuttle made from TPV O-rings made from EPDM NSF approved Kegland Part Number: KL15509
$39.99
-
Beer Faucet Shank | Tower Shank | Stainless | Duotight Compatible Barb | Intertap® | NukaTap®
Outfit any 3" diameter draft tower with these stainless steel Intertap Tower Shanks with Duotight compatible tailpiece. The 1/4" barb pairs perfectly with the Duotight 6.35 mm x 8 mm reducer (DUO100), allowing you to quickly and easily connect 8 mm OD EVABarrier draft line (D1717 & D1718). The Duotight fitting is sold separately and can be found below under "You Might Also Need". Please note these shanks are not compatible with Perlick flow control faucets. Kegland Part number: KL01137
$19.49
-
Beer & Gas Quick Disconnect (QD) - 1/4 in. MPT x Male Shut-Off
Works with our H550 series Quick Disconnects. This is a male Quick Disconnect with 1/4" MPT on the other side.
$7.99 $6.79
-
Duotight Push-In Fitting - 8 mm (5/16 in.) Elbow
This Duotight elbow fitting is compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL0240
$2.79
-
Ultra Barrier™ Gas PVC Free Tubing - 5/16 in.
A highly flexible, environmentally friendly, gas tubing that is BPA and PVC Free! Ultra Barrier™ Gas tubing from EJ Beverage is an excellent alternative to PVC. It is constructed of a unique compound that is PVC Free and BPA Free; it contains no DEHP phthalates or other plasticizers. This tubing is clear with a red stripe so you can identify it as a low pressure gas line. It does not emit dioxins and has extremely low extractables/leachables. This amazing tubing remains flexible at lower temps, has ultra-low permeability, and superior barrier properties. If you want a tubing that won't leach large amounts of chemicals, this is it! Clear tubing with red stripe for identification as low pressure gas line PVC Free and BPA Free - containes no DEHP phthalates or other plasticizers Environmentally friendly production - does not emit dioxins Extremely low extractables/leachables High flexibility Remains flexible at lower temperatures Ultra-low permeability Superior Barrier properties Temperature range of -40 to 125° F Working pressure of 51 psi
$10.49 - $152.99
-
Duotight Flow Control Ball Lock Quick Disconnect (QD) | Beverage Out | Adjustable Flow Rate | 8 mm Duotight
If you want an easy way to balance your beer lines, this is the way to do it. One of the benefits of Flow Control disconnects is you don't need to rely on the small ID or line length to apply flow resistance. Rather than adjusting your line length or size, simply apply additional restriction directly on the Quick Disconnect (QD). This is perfect for people who want to serve a large range of beverages with differing carbonation levels without having to customize each line. Now with the added benefit of Duotight fittings built in. Please be aware that even in the fully open position these FC disconnects do have some inherent flow resistance so you should use either shorter line or larger ID line that you would when compared with traditional ball lock disconnects. Flow Control QD vs. Flow Control Faucet One of the only drawbacks of flow control devices is that they inherently create a small amount of turbulence and therefore can cause foaming. In the past, flow control faucets have been the only common option. Flow control faucets are very popular but due to the fact that they are placed at the very end of the beer line they have no head pressure. As a result, any turbulence created can cause foaming and carbonation to come out of solution. Flow control ball lock disconnects like these on the other hand have the ability to restrict the flow before the beer enters the beer line so the head pressure created by the beer line keeps the carbonation in solution. Even in the instance that high turbulence is created the beer will be far more resistant to foaming issues. For this reason, flow control ball lock disconnects like these have significantly better performance allowing you the flexibility to adjust line resistance easily but without the introduction of turbulence that creates foaming. It cannot fix over-carbonated beer, but it can reduce the amount of beer line you would need to pour without excessive foaming. Duotight Ball Lock QDs The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required. Duotight Push-to-Connect These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done! Compact The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines. Overmolded Poppet The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out. Tool-less Disassembly Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects. Extreme Chemical Resistance No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing. Toughness This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough! Features: Ball Lock Quick Disconnect - Bev Out Adjustable flow rate Direct connect 8 mm EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Dissamble by hand for quick and easy cleaning KegLand Part Number: KL21418
$16.49
-
Taprite Dual Gauge CO2 Regulator | High Performance Primary Regulator | 0-50 PSI Working Pressure | CGA320 Inlet | One Way Shutoff Valve | 5/16" Barb Outlet
High performance primary regulator designed to handle the workload of dispensing from multiple taps without freezing up! Dual high-pressure and low-pressure gauges to easily reference CO2 cylinder pressure and output pressure Pressure settings are easily adjusted by hand using the large plastic adjustment knob CGA320 inlet features a built-in gasket where the unit attaches to the CO2 tank—eliminating the need of replacing fiber washers with each tank swap Made in the USA. Taprite is one of leading manufacturers of gas regulators and draft dispensing equipment One-way shutoff valve outlet protects your regulator from backflow and can be turned on/off to stop gas flow without needing to close your tank When it comes to CO2 regulators, we’ve tried them all. This quality unit by Taprite is our favorite on the market. It’s no wonder this regulator is trusted by so many breweries and beer bars—it represents the best quality at a great price. Available in a standard, single-body model, as well as a dual-body model which allows you to send different pressures to two separate kegs from the same CO2 tank! The things you’ll love about this regulator are: The large front knob makes pressure adjustment tool-free, easy & fast. The built-in gasket where the regulator connects to the CO2 tank eliminates the constant replacement of fiber washers every time you change out your tank. The barbed outlet features a one-way on/off valve which prevents backflow and protects the regulator’s internals. The gauges are easy to read. The low pressure gauge reads from 0 to 60 psi. The optional available gauge cage is the best on the market. This is the T742HP model, where the HP stands for high performance; it won't freeze up when multiple taps are running at once. Best of all is the consistent pressure regulation. With many regulators the pressure can 'creep' up over time. This unit holds the pressure rock steady. No drifting. Built by Taprite, an American company.
$87.99
-
Duotight Push-In Fitting - 8mm (5/16 in.) x 8mm (5/16 in.) Male Elbow
This Duotight to Male Elbow fitting can be used to route tubing connecting to 8 mm Duotight Ball Lock QDs. This is a great way to keep tubing organized and out of the way in your kegerator. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL18456
$2.19
-
Intertap® Stainless Steel Beer Faucet | Forward Sealing
Forward-sealing design prevents beer residue from gumming up the faucet! Threaded spout can be replaced with a variety of attachments Unique sliding shuttle design allows the faucet to last longer than standard floating o-ring design 304 stainless steel construction The patented Stainless Steel Intertap Faucet is a forward sealing faucet that represents the most modern faucet design. It has a modular, threaded spout which can fit a variety of different attachments including a growler filler or a stout spout. In normal rear-sealing faucets the entire faucet has to drain of beer. In forward-sealing faucets the faucet keeps beer in it so the inside doesn't have a chance to get sticky, making cleaning much easier. It also reduces the chance of off flavors transfering to your beer while you pour. Other forward sealing faucets use a floating o-ring, which is just as sanitary but requires the o-ring to move inside the faucet body in order to seal correctly. This can become a problem as the faucet ages. Intertap faucets use a sliding shuttle that guides the o-ring into the perfect position every time. The threaded spout easily unscrews from the faucet and can be replaced by a growler filler or stout spout quickly and easily. Pour a pint and then fill a growler in no time at all. 304 Stainless Steel construction so you don't have to worry about chrome plating wearing off and exposing your beer to brass. Kegland Part number: KL00970
$42.99
-
Beer Line Tidy - Beer and Gas Line Organizer
Who doesn't love a well-organized kegerator or keezer? The Beer Line Tidy from KegLand offers an easy solution to straighten out your rat's nest of draft lines. Simply remove the paper backing and use the strong 3M adhesive to attach this beer/gas line organizer to whatever device you like. This keeps your beer and gas plumbing neat and tidy so your draft system looks as good as it works. Primarily designed for 8 mm (5/16") OD tubing, but works with 9.5 mm (3/8") OD and 6.35 mm (1/4") OD tubing as well. Note: for best results, apply the adhesive at room temperature and let stand for 72 hours before applying load. KegLand Part Number: KL22767
$3.59
-
Hand Pump Pressurized Keg/Beer Line Cleaner | 1 Gallon
Designed specifically for cleaning draft lines, this hand pump pressurized keg is easy to use and doesn't need CO2 like many other line cleaning kegs. After filling the keg with cleaning solution, unscrew the beer line from your sanke coupler and attach it to the included beer thread coupler to hook it up directly to the cleaning keg. Pumps from the bottom to the top, allowing you to leave the cleaning solution in the line for 15 minutes. We recommend cleaning your lines every time you switch out a keg or every 6 weeks, whichever comes first. 1 gallon capacity Comes with a 3/16” x 5/16” hose Included Female Beer Thread (5/8" BSP) Coupler Also Included: Beer Line Cleaning Brush With 8" length and 5/8" diameter, this brush is ideal for cleaning keg couplers, draft faucets, 3-Piece airlocks, 1/2" bottle fillers, and 3/8" or 1/2" spigots. Features a coated tip to prevent scratching or damaging surfaces. Draft Beer Faucet Brush and Plug Keep fruit flies and other bugs out of your draft beer faucets when not in use. This plug style brush will clean the faucet nozzle on the way in and when pulled out. It works with standard beer faucets and Intertap, NukaTap, and Perlick brand faucets. Double Shank and Faucet Wrench Draft wrench designed to tighten the hex nut on the back of a faucet shank. Well suited for keezers or even draft towers. Features a pin wrench for tightening the faucet coupling ring where your faucet attaches to the draft shank.
$65.99
-
Self Closing Faucet Spring | Intertap® | NukaTap®
Turn your Intertap or Nukatap faucet into a self-closing faucet with the use of this stainless steel faucet spring. Forces the tap handle back to the closed position when you let go. This spring is designed to work with the Intertap Stainless Steel shanks, though we have found it also works with our D1245A. Made from 304 Stainless Steel. Not compatible with Flow Control faucet models or other brands of faucets. Kegland Part number: KL00994
$2.79
-
Duotight Draft Regulator Board | Gas Manifold | 4 Way
Serve beverages at different pressures without the need for multiple CO2 cylinders, dual body regulators, or expensive gas manifolds Feed a single pressure to the gas board from your regulator and then step down the pressure on each Duotight regulator Use one line for serving ales, another for soda or seltzer water, and another for carbonating a freshly filled keg All parts shown are included and snap together quickly thanks to Duotight push-to-connect fittings and rigid plastic joiners Duotight In-Line Regulators feature built-in pressure gauges that read 0-60 PSI and can be swapped out for different ranges if desired The Duotight Draft Regulator Board is a simple and cost-effective solution to serving beer and other beverages on draft at different pressures. With a standard CO2 tank and CO2 regulator, you can feed gas at a single pressure into the regulator board and then fine tune individual pressure settings for each gas line via the Duotight In-Line Regulators. These regulators feature built-in pressure gauges that make adjustments super simple and check valves are included as standard so you never have to worry about back flow into the regulator. This kit includes everything you need to assemble your regulator board and can be customized so the gas inlet is on the right or left side—whichever makes the most sense for your home draft setup. Duotight push-to-connect fittings and the precut rigid joiners make assembly a breeze and only takes 10-15 minutes! The draft board kit comes in two options—with or without shut off valves. These valves offer peace of mind and allow you to shut off gas flow to any line that is not in use. If you ensure that your system has no leaks, they aren't technically needed, and you can always fully tighten your Duotight Regulator adjustment knob for added protection. But that little extra security might help you sleep easier at night! One advantage of choosing no check valves, however, is that it will leave room at the top of the board to label your gas lines. One of the coolest features of the Duotight In-Line Regulator is that the included pressure gauge can be swapped out for different pressure ranges. The standard gauge reads 0-60 PSI, but if you have one line that will always be used for serving Ales, you can swap to a 0-15 PSI gauge that will be a little easier to read and make precise adjustments. There's also a Digital Pressure Gauge available that provides backlit instant reads and is rated from 0-90 PSI. Need more than 4 gas lines? Check out the 6-Way Duotight Draft Regulator Board. Please Note: Full assembly required. The gas board, regulators, and fittings will arrive loose. Please see our instructions and assembly video below. Stepping Down Pressure The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability. Ideal regulation scenario (10 PSI less than inlet pressure) Example of 30 PSI inlet translating to 0–20 PSI output Kit Includes: 4-Output Gas Board (4) Duotight In-Line Regulators (4) Duotight Check Valves (4) Duotight Shut Off Valves (if selected above) (3) Duotight Tees (1) Duotight Elbow (15) Rigid Plastic Joiners NOTE: All Duotight fittings and rigid plastic joiners come as 8mm OD. Mounting hardware is included for the regulators but not for mounting the board itself to a wall or the inside of your kegerator/keezer. If you select the option without shutoff valves, you will be left with some spare joiners after assembly.
$98.99 - $109.99
-
KOMOS® Gas Manifold | Aluminum | 1/4 in. Flare
Keep multiple kegs under pressure at once! Predrilled holes for easy mounting EVABarrier Draft Tubing fits perfectly on the 1/4 in flares Gas manifolds are the best way to provide CO2 to multiple kegs inside your kegerator or keezer. The KOMOS manifold features 1/4" flare gas inlet and check valves that provide much more flexibility compared to manifolds with barbed valves. Choose the type and size of draft tubing that you prefer. Use 1/4" or 5/16" gas line with the appropriate Flare Fitting Set (KEG607 or KEG640), or use EVABarrier—our draft line of choice—with the appropriately sized Duotight Fitting (DUO106 or DUO120). You can also replace one or more of the check valves with a Ball Lock Post Bulkhead, which allows you to use a gas-in ball lock jumper line as a quick connect option. Need something bigger than a 4-way manifold? No problem! With this 1/4" Nipple, you can join multiple manifolds for as many outlets as you need. Features: 1/4" Flare connections 1/4" BSP ball valves Rated to 100 psi Wall mount holes Made from aluminum, brass, and stainless steel Size Overall Length 2-way 5.25" 3-way 7.25" 4-way 9.25" The above measurements are from the tip for the brass flare inlet to the plug on the opposite end. Each manifold measures approximately 3.5" from the mounting holes to the tip of the valve. Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.
$26.99 - $36.99
-
Duotight Push-In Fitting - 8 mm (5/16 in.) Joiner
This Duotight joiner fitting is compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL02370
$2.79
-
Vacuum & Pressure Relief Valve - 1.5 in. T.C.
This 1.5 in TriClamp pressure and vacuum relief valve is a great way to protect your tank. It will relieve pressure over 1.5 BAR but will also let in air if the tank is a vacuum inside to prevent the tank from imploding. Features: Relief pressure: 1.5 BAR (22 psi) Allows pressure in during a vacuum 1.5 in TC Kegland Part Number: KL01823
$109.99 $71.49
-
Beer & Gas Tubing Quick Disconnect (QD) - 3/8 in. Barb x Male QD
Plastic quick disconnect with 3/8" barb which can be used with either 1/4", 5/16" or 3/8" line. The quick disconnect functionality is activated by a shrouded thumb latch on the female QD. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you need not worry about them leaking gas. The o-ring is food grade buna-n. This is a non-valved QD. It does not have an internal shut-off like H550A. For the female side, see our H550B.
$5.99
-
Duotight Push-In Fitting | 8 mm (5/16") Stem x 6.35 mm (1/4") Barb
This handy part is what you need to connect one side into a standard 8 mm Duotight fitting and secure the other side with 1/4" ID tubing using a hose clamp over the tube. We have wide range of stainless stepless hose clamps that you can purchase here. KegLand Part Number: KL25935
$1.09
-
16g Threaded CO2 Cartridge | Pack of 6
16g threaded CO2 cartridges that work great with the KegLand Core 360 Mini CO2 Regulator or the Duotight Mini CO2 Regulator. Comes in a package of 6 cartridges. Please note: due to air shipping restrictions, this product is only eligible for ground shipment within the contiguous United States.
$11.99
-
Push-In Pressure Gauge (0-150 psi)
The Push-In Pressure Gauge comes with an 8 mm (5/16 in.) barb, specifically designed to be compatible with 8 mm Duotight fittings. The dial face is triple-scaled to read in psi, bar, and kPa. 8 mm (5/16") push-in barb Rubber coated to protect gauge 0-150 psi / 0-10 bar / 0-1,000 kPa Kegland Part number: KL07696
$9.89 $6.43
-
EVABarrier Double Wall Draft Tubing - 3 mm ID x 6.35 mm OD
EVABarrier Draft Tubing in 13 ft. Length is now available for pre-order. Place your order now and we will automatically ship it to you when it's available. The current estimated availability is early 2025. If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 3 mm (1/8") ID size is perfect for mobile draft applications or home draft systems where only a short beverage line is needed. Lengths of 3.2 ft. per line are all that you'll need for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 3 mm (1/8") Outer Diameter - 6.35 mm (1/4") PVC, BPA, and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. Kegland Part number: KL25331
$10.99 - $20.99
-
Duotight Compatible | Hand Held Beer Faucet | Cobra Tap | Picnic Tap | Black Plastic
The standard plastic handheld faucet modified for use with Duotight fittings and EVABarrier draft tubing. The 6.35mm end piece can be paired with the 8mm x 6.35mm Duotight reducer to use with 8mm OD EVABarrier tubing. Commonly called a "cobra tap" or "picnic faucet". Duotight fitting sold separately. KegLand Part Number: KL21821
$6.59
-
KOMOS® Premium Dual Gauge CO2 Regulator | 0–60 PSI
Wide 0-60 PSI operating range suitable for both dispensing and rapid burst carbonation Ideal for seltzers and high-carbonation drinks requiring 30-40 PSI Includes a Duotight adapter for EVABarrier tubing and a 1/4" flare fitting with barb, allowing for quick and adaptable gas line setups Heavy-duty steel gauges with rubber bumpers, robust body, and precision diaphragm ensure long-lasting, accurate pressure adjustments Compatible with standard US CO2 tanks and can be adapted for use with Nitrogen / Argon tanks The robust body and precision diaphragm provide high flow rates, and the pressure can be easily and precisely adjusted with the hand dial. Extra thick stainless gauges come with rubber bumpers for added protection. The dial faces are triple-scaled to read in psi, bar and kPa. The PRV is rated to 65 psi (4.5 bar) for added safety while in use. Comes with male flare thread gas-out with included 1/4" barb and nut. Easily swap out the barb to a different size if desired. On the back of the regulator body are three M6 screw holes for mounting (screws not included). Each KOMOS regulator includes a Duotight Adapter, allowing for quick connection of EVABarrier draft tubing for a solid, yet easy to change, way of connecting gas line. Add Duotight Tees to easily split the line to multiple kegs. The regulator is CO2 ready with standard US CGA320 threads. It can also be used with Nitrogen or Argon tanks with the optional CGA320 x CGA580 Adapter. Features: 0–60 PSI operating range Low pressure gauge reads from 0–100 Pull ring PRV rated to blow off at 65 PSI Strong, robust design Highly accurate precision diaphragm 1/4" flare fitting with barbed outlet & Duotight adapter fitting M6 mounting screw holes Made in accordance with AS 4267
$59.99
-
Beer Faucet Shank | Stainless | 4" | 8 mm Duotight Adapter | Intertap® | NukaTap®
Comes with a back nut, plastic collar, hex nut, and 8 mm Duotight Adapter compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Requires a 1" hole saw for installation. When set in place, the shank will only have about 2 1/2" of length to pass through your wall or fridge door, due to the length of the collar and back nut. Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 5-1/8" - Total Length (Tip to Tip) 4" - Shank Length (Without Nut & Barb) 3" - Thread Length 2-1/2" - Pass Through Length Kegland Part number: KL11945
$36.49
-
MoreBeer!® Tap Handle for Recipe Kits | Beer Faucet Handle | Chalkboard Insert | Black
How many times have you been asked "What's on this tap?" The MoreBeer! tap handle is designed to work with our full lineup of recipe kits. Each recipe sheet has a custom color cut out that can be slipped into the handle. We had a lot of fun creating over 150 original designs when the tap handle was originally released, and we continue to create new tap handle cut outs for every recipe kit we develop. We think you and your friends will love them. Not using a MoreBeer! kit? No problem! Each new tap handle also comes with a removable, erasable chalkboard surface. Additionally, the back of the tap handle features a chalkboard surface that can be written on as well, which is handy and cool if your tap handle is seen from both sides. The insert is made of a thin sheet of metal and coated with chalkboard paint. The outer portion of the tap handle is made of wood and also painted with chalkboard paint. Note: You might need to use a bonnet angler (D1270) if you converted an upright refrigerator. Bonnet anglers allow longer tap handles to sit in a more vertical position so they do not angle back and hit the refrigerator door or wall. Tap Board Features: Designed to work with MoreBeer! recipe kits Includes removable metal chalkboard insert when not using a MoreBeer! recipe kit Back of tap handle also serves as chalkboard surface Dimensions: 7.25" H x 2.25" W x 0.75" D
$18.99
-
Vinyl Tubing (Reinforced) - 1 in.
Use this reinforced vinyl tubing any place in your brewing system where you want an added layer of protection from tubing failure. This 1" ID Reinforced Vinyl Tubing is food-grade approved up to 158F. It is often used in a in a brewing system where higher pressures will be used or for commercial applications. Because it is reinforced, it is less flexible than standard vinyl tubing. Tubing has a max working pressure of 250 PSI.
$25.99 - $407.99
-
NukaTap® Mini Beer Faucet Assembly Kit | Flow Control Ball Lock Quick Disconnect (QD) | Duotight Adapter | Self Closing Spring
The ultimate portable draft faucet! Compact & lightweight with all the advantages of a standard NukaTap forward sealing faucet Includes NukaTap Mini, Flow Control Ball Lock QD, Duotight Adapter, and Self Closing Spring Forward-sealing design prevents beer residue from gumming up the faucet Reduced first pour foam due to low thermal mass and conductivity Perfect for mobile draft, mini kegs, sampling from fermenters, and can even be installed on your kegerator or keezer Mini Design – Ideal Flow Rate for Small Systems Most conventional beer faucets are designed with 3/8" diameter spouts so you can pour a pint in just over 10 seconds. This type of flow rate is great for high turnover bars and commercial venues but isn't necessary or even desirable for all applications. For compact portable systems and home draft systems, a slower flow rate is easier to control and further reduces foaming issues due to the low liquid volume stored in the body of the faucet. The NukaTap Mini is also more ideal for pouring smaller doses. For example, cocktails where 5-8 oz of liquid is dispensed is difficult to control with a high flow rate tap. For portable systems, the NukaTap Mini with the Flow Control Ball Lock QD & Duotight Adapter assembly is small enough to literally put in your pocket, making it ideal for mini keg setups that you want to be portable or that you want to easily fit inside a domestic fridge where space is tight. Forward Sealing Forward sealing faucets are absolutely the way to go when it comes to beer taps. Old legacy taps still exist in the industry that are simply poorly designed. The issue with rear sealing faucets is that beer dries up on the internal piston. Aside from being unsanitary, as more and more beer dries up in these components the faucet can almost glue completely shut causing damaged seals or broken handles (this is particularly the case if it's left for some time to dry out with beer inside). These older legacy designs still exist probably due to poor education. The forward sealing designs do not have this problem and the tap drains out completely with no beer drying up on the mechanical moving parts in the same way. This makes the tap more sanitary and reduces maintenance. In many instances the price is similar so there is no reason to use a poorly designed rear sealing faucet. All NukaTap faucets are forward sealing. Laminar Flow Just like the NukaTap SS and NukaTap FC, the NukaTap Mini has been designed with laminar flow in mind. Laminar flow is critical for a beer tap as it means you will pour the beer with minimal foaming and a substantial reduction in wastage. Think about how many times a beer faucet opens and closes in its lifetime. 1,000 or maybe 10,000 times? Laminar flow saves wasted beer in excessive foam and the better laminar flow easily pays for itself in a reduction in lost beer. To use poorer designed faucets is essentially flushing money down the sink. Extensive modeling has been done on the NukaTap design to improve laminar flow. Integrated Seals That Are Indestructible and More Sanitary Unlike other designs, the NukaTap Mini body is made from Polyketone (POK) making it strong, robust, and able to be autoclaved. The seals are also over-molded from Santoprene® making them hard wearing so they will literally last for the lifetime of the tap without the need for replacement. Santoprene® and POK both have excellent resistance to chemicals such as caustic soda, peroxide, phosphoric acid, lactic acid, citric acid, acetic acid, and all common chemicals sold and used in the beverage industry. The seals internally are over-molded meaning no fissures or cracks exist for bacteria, crud, or yeast to hide. Superior First Pour Foam Due to Low Thermal Mass and Conductivity First pour foam is an issue caused by a warm tap body. For most faucets to pour well it's important to dispense enough beer to cool the tap body down to reach maximum performance. In addition to this the conductivity of the tab body also makes this worse so insulative materials simply work better than conductive materials. The NukaTap mini not only has very low thermal mass but is also highly insulative being made mostly from Santoprene® and POK. The combination of these two factors in conjunction with superior laminar flow makes for the lowest "first pour foam" effect out of any tap ever produced. Long Shank Alternative Most conventional beer faucets require a large 3/4" hole to be drilled through the side of your refrigerator, keezer, or cold box wall. Traditional long shanks also generally have a large volume of liquid that sits inside the wall unrefrigerated which is not ideal. New long shank alternatives developed for the NukaTap Mini are designed to suit any wall thickness and greatly reduces the stagnant beer sitting in the shank itself. For walls up to 2.7" thick, these wall mount shank kits include three screws, however if the wall is thicker, you can also use 6 small wood screws or something similar and attach three screws from the front and 3 from the back allowing you to go into any wall type. Another advantage of this new design is the tap will never accidentally rotate. Typically, other long shank beer taps rely on the hex nut on the shank to be done up tight enough to prevent rotation but if the wall compresses (often the case with foam walls) the tap is allowed to rotate. This new design has three fixing points making it impossible for the tap to rotate accidentally as the interlocking teeth behind the collet allow you to set the angle and then do up the collet to fix the tap permanently in that position.
$43.99
-
Duotight Flow Stopper Automatic Keg Filler
The Duotight Flow Stopper is a handy devicie to use while filling kegs or when transferring between kegs during filtering or after fining. Simply attach the Flow Stopper to the gas post of your keg, then when the keg is full it will automatically cut off flow and prevent excess beer from exiting your gas post and spilling onto the floor. For even better results, we recommend using the Flow Stopper with the BlowTie Spunding Valve. The BlowTie will enable you to apply head pressure to the keg, meaning you can control the flow speed and reduce the foam generated in the filling process. You will need a short length of 8 mm OD EVABarrier tubing to connect the BlowTie to the outlet of the Flow Stopper. Includes: 2 x Duotight 8 mm x 5/8" FPT (DUO104) 1 x Duotight 8 mm elbow (DUO107) 1 x Duotight 8 mm x 1/4 in. flare (DUO106) 1 x Ball float 1 x Stainless spring 2 x 8 mm OD EVABarrier joiners 1 x Acrylic sight glass Ball lock fitting and BlowTie spunding valve not included. Kegland Part number: KL09393
$16.49
-
Kegland CO2 Cartridge - 74 g
These cartridges give the oomph to your mini-regulator dispensing unit! Perfect for dispensing your beer on the go. One canister will push between 1-4 Cornelius kegs, depending on how it is used and the CO2 consumption required. With the 74g adapter piece, these cartridges can be used with the KegLand Core 360 Mini Regulator or Torpedo Mini CO2 Regulator. 5/8-18 UNF threading Kegland Part Number: KL16889 Please note: due to air shipping restrictions, this product is only eligible for ground shipment within the contiguous United States.
$12.99 $11.04
-
Duotight Push-In Fitting - 9.5 mm (3/8 in.) x 1/4 in. Flare
This Duotight fitting with 1/4" Flare is perfect for flared gas ball lock and pin lock disconnects. Can also be used to connect gas line to the flare fitting found on the KOMOS® CO2 Regulator. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Although this fitting would also fit a beverage disconnect, 9.5 mm OD EVABarrier is only recommended for beverage line in long draw draft set ups. The Duotight fitting does not require a flare washer. See the instructions below for how to ensure a leak-free connection when attaching to flare fittings. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL11037
$3.89
-
Stout Spout | Stainless Steel | Intertap® | NukaTap®
Simply unscrew the normal spout on an Intertap faucet and screw this stout spout in its place to pour your nitro brews. This spout has a creamer/aerator disc inside that strips out the nitrogen gas for a creamier beer. For additional disc options, check out the 7-Disc Creamer/Aerator Kit. Compatible with Intertap and NukaTap faucets. Stainless Steel Construction Kegland Part number: KL01021
$14.49
-
Hand Held Beer Faucet | Cobra Tap | Picnic Tap | Black Plastic
This standard, black plastic handheld faucet will remind you of the one you used to pour beer in college! A great, affordable and efficient way to serve beer at any gathering or event. Commonly called a "cobra tap" or "picnic faucet." 1/4" outlet barb. 3/16" line will fit if softened in hot water for about 10 seconds prior to assembly. The tap threads apart for easy cleaning. Please be make sure the threaded portion is assembled tight before use. Kegland Part number: KL00963
$4.99
-
Stainless Steel Draft Coil
This 50' x 3/8" coil, manufactured in the MoreBeer! metal shop, is perfect for the enterprising homebrewer who wants to build or upgrade a jockey box. When compared with 5/16" coils that are usually used to make draft boxes, the 3/8" coil holds more beer and offers more surface area for faster cooling. And, because there is less resistance from the larger diameter tubing, the beer can be pushed through the lines with less CO2 pressure. Lower applied CO2 pressure means your beer will not over carbonate and foam wildly if a keg is left on tap for longer than an afternoon. Over-carbonation is often an issue for homebrewers or beer drinkers who are using a draft box for an overnight party or weekend. 8 1/2" wide x 10" tall. 304 grade stainless steel
$98.99
-
KegLand Core 360 Mini CO2 Regulator | Interchangeable Gas Outlet | Swappable Pressure Gauge | SodaStream Compatible
Unique Core Puncturing / Actuator results in zero gas lost from screwing in CO2 cartridges Interchangeable ball lock disconnect orientations. 45° for plastic QDs or 90° for stainless QDs 6.5mm Duotight compatible hose barb Swappable mini pressure gauge remains well protected within solid cast brass regulator body Corny-style 65psi Green PRV for added safety and manual depressurizing Switch from 16g to 74g CO2 cartridges with an adapter fitting The new Core 360 Mini CO2 Regulator from KegLand represents a huge jump forward in the mini regulator market. After much feedback on how to make mini regulators more compact, sturdy and efficient, the brilliant engineers at KegLand have come up with this mini-beast. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. Heavy Duty Construction Starting with the body of the regulator, this unit is made from chrome-plated solid cast brass which means it will stand up to quite a bit of abuse. Unlike most mini regulators, the pressure gauge on the Core 360 is safely recessed in the regulator body, so if you ever drop it there is little chance that you'll damage the gauge. What's more, the gauge is removable, so you can swap it out with another mini gauge with a pressure range that better suits your application. Unique Cartridge Connection What really sets this unit apart from other mini regulators is the way in which you insert a CO2 cartridge. A common complaint with these types of regulators is that you can lose a lot of gas from the cartridge just from threading it into the regulator. There's that brief period where the cartridge has been punctured but you haven't fully threaded it into the regulator to form a seal. If you're not quick enough, this can result in a significant amount of lost gas. The Core 360 has a unique design feature where inserting the cartridge is a 2-step process. First you fully thread in the cartridge so it forms a seal before it's opened, and then you screw down the actuator pin to release gas into the regulator. Simple and effective. Furthermore, the Core 360 Mini Regulator is designed to be compatible with both 16g and 74g cartridges. Out of the box it will be ready to accept 16-gram 3/8"-24 UNF threaded cartridges. But with a simple adapter you can switch to 74-gram 5/8"-18 UNF threaded cartridges. Interchangeable Gas Outlet Another feature we haven't seen before on a mini regulator is the interchangeable gas outlet. You can use the swivel nut connection to directly attach the regulator to a flare ball lock disconnect, or you can swap to the 6.5mm Duotight-compatible barb and connect draft tubing. This is a great option if you want to dispense a commercial keg without the need of a ball lock to sanke coupler adapter. The regulator also has two outlet options at either a 45° or 90° angle which makes this the ideal mini regulator regardless of whether you use plastic or stainless steel ball lock disconnects. SodaStream Compatible If you remove the 16g cartridge bushing, you'll find TR21-4 female threads for use with SodaStream gas cylinders. These can be a great option for mobile dispensing as they provide much more gas than a CO2 cartridge and are more easily transported than a full CO2 tank. Includes: KegLand Core 360 Mini Regulator 6.5mm Duotight-compatible hose barb Female Flare Fitting for MFL Disconnects Port end cap 65psi Green PRV SodaStream to 16g thread bushing KegLand Part Number: KL20404 Warning: Do not overtighten onto your cylinder. It is recommended that you use a spanner to hold the neck of your SodaStream cylinder while attaching and detaching the Mini 360 Core Actuator Regulator. Mini 360 Core Actuator Regulator | User Guide
$82.99
-
Torpedo Keg | Hand Held Beer Faucet | Cobra Tap | Picnic Tap | 1/4" Barb | Stainless Steel
Finally, a high-quality, stainless steel, handheld faucet for discerning beer servers on the go! For too long there have been no other option than the standard plastic picnic tap. Torpedo Keg decided to fill the void with a top-shelf mobile draft faucet made with stainless components and internal parts. You'll feel the quality in the smooth pouring action and love the weight of it in your hand. This is definitely not the beer tap you used in college! 1/4" OD outlet barb will work well with 1/4" or 3/16" ID draft tubing.
$16.99
You have seen 96 out of 483 products