Prevent electrocution! This is the best way to plug in a pump or other brewing or winemaking equipment because it will trip the circuit when any water flows on the ground wire. 15 Amps 1875 Watts 125 VAC 60 Hz.
A replacement pump head for the H308 diaphragm pump, should the diaphragms become worn or get damaged by passing particulate matter through them.
Please Note: This pump head does not include the Pre-Filter or the Elbow fittings that are connected to your hoses, those will need to be transferred over from the existing pump head or purchased separately.
Transfer the clearest beer possible from first pint to last with the Super Sucker Filtered Racking Buoy! Stainless steel float allows you to pull liquid from the top of your vessel rather than transferring out from the bottom Sediment falls out of suspension over time, especially at cold temperatures, so the clearest beer is always at the top! 10 feet of tubing can be cut to your preferred length for both the pump inlet and outlet Made for use with the Super Sucker Transfer Pump The Filtered Racking Buoy kit allows you to transfer the clearest liquid possible with the Super Sucker Transfer Pump. Whether you're transferring beer or wine, the clearest liquid will always be at the top of the vessel as solids fall out of suspension and settle to the bottom over time. The stainless steel float will position your transfer tubing at the top of the liquid so you can pull from the top down and cease transferring when you get near the sediment. The filter attachment will add a layer of protection for the pump and will leave solids behind in your fermenter or storage tank. Includes: Stainless float (1.75" Ø) Filter attachment 10' length of 3/8" ID silicone tubing (3) hose clamps
The redesigned quick disconnect pre-filter for the H308 Super Transfer pump now features a replaceable filter screen. Pick up a replacement or keep a spare on hand. When your filter mesh screen is past its prime, simply replace the screen rather than replace the whole pre-filter. Please note: this filter screen will only work with the current generation pre-filter. If you purchased the Super Transfer pump before 2020 and have the original pre-filter, you will need to upgrade to the newest version (H308C) to be compatible with this replacement mesh screen.
Digital flow-meter perfect for winemaking, beer making, cider making and more. Equipped with reset function, a cumulative totalizer reset, and a non-resettable totalizer. Calibration function to adapt the instrument to fill by gravity, or to fill with transfer pumps.
Features:
Capacity from 30L/7.9G to 130L/34.3G per minute
Display changeable from liters to gallons
Minimum pressure 0,3 bar, maximum pressure 16 ba
1" BSPP (straight thread) outlets (includes 1" barbs)
Accuracy + -1% of indicated value after calibration
Repeatability + – 0.3%
Battery Powered
Rated to a maximum temperature of 85 C°(185 f°)
The 50C rating in the manual is a typo.
Heavy-duty hose clamp suitable for 1-1/4" to 2-1/8" OD tubing
Effective and removable
Easily adjusted with a flathead screwdriver
Made from stainless steel
A heavy duty hose clamp for large OD tubing. As effective as a pre-formed clamp but without the expense or permanence.
Replacement elbow fitting for the H308 diaphragm pump. This fitting is typically only used on the pump outlet, but can also be placed on the inlet in lieu of the Pre-Filter. Please note that doing so puts the pump head at increased risk of damage from particulate matter.
Kink and crush resistant suction & discharge rubber hose, designed for demanding applications that require high temperature and chemical resistance ForgeFit barbed connector and crimp sleeve system are designed to provide a long life and easy to clean hose connection Hose barb skips the first barb to provide a gapless and smooth transition to the tubing Our sleeves are machined from pipe to meet sanitary standards, avoiding the uneven compression and hard points caused by welding, and offering a superior surface finish that is both more hygienic and visually appealing Novaflex Connoisseurs Beverage Hose Meets 3-A (cert# 1803), FDA & USDA standards Tubing sets made from ForgeFit fittings and Novaflex Connoisseurs food & beverage tubing that are assembled in the MoreBeer! Pro metal shop in Pittsburg, California. The options above are already assembled and ready to ship. If these options do not suit your needs, custom lengths can also be made to order. Novaflex is a special kink and crush resistant suction & discharge rubber hose, designed for those more demanding applications requiring a product that meets 3-A (cert# 1803), FDA & USDA standards. This tube is for non-oily applications. Designed to meet the temperatures and chemical resistance associated with “cleaning in place” systems. This ultra smooth microbe resistant tube is built on special stainless steel mandrels for cleanliness. The ForgeFit barbed connector and crimp sleeve system is designed to provide a long life and easy to clean hose connection. The long barb and the long sleeve provide a secure crimp without crushing the hose. Triple banding can slip or damage the hose during installation and has sharp edges. The ForgeFit® hose barb skips the first barb to provide a gapless and smooth transition to the tubing to make it easier to keep clean. Our barb has a stop to ensure the hose does not creep closer to the clamp in service. Don't forget to add hose bumpers to your order to protect your investment! The ForgeFit® Silicone Hose Bumper is designed to protect your hose ends by absorbing the impact of the hose end hitting the floor when it's dropped. The unique built in handle makes it easier to grab and saves your back. Novaflex Construction: Tube: White Chlorobutyl Reinforcement: Multiple plies of polyester tire cord & dual monofilament helix Cover: Gray EPDM abrasion resistant Temperature Range: -40° to 240°F (CIP to 248°F) Not for continuous steam service in. mm ID 1.5 38.1 OD 2.14 54.35 Bend Radius 4.5 114
Due to high demand, some of these items are currently out of stock but available for pre-order. Please check status notes below when selecting a size option to see if it is In Stock or tagged as PreBook. We will automatically ship this to you when we receive more inventory. Kink and crush resistant suction & discharge rubber hose, designed for demanding applications that require high temperature and chemical resistance ForgeFit barbed connector and crimp sleeve system are designed to provide a long life and easy to clean hose connection Hose barb skips the first barb to provide a gapless and smooth transition to the tubing Our sleeves are machined from pipe to meet sanitary standards, avoiding the uneven compression and hard points caused by welding, and offering a superior surface finish that is both more hygienic and visually appealing 1" ID tubing is sometimes preferred to 1.5" as it is easier to handle and decreases product loss Novaflex Connoisseurs Beverage Hose Meets 3-A (cert# 1803), FDA & USDA standards Now selling tubing sets made from ForgeFit fittings and Novaflex Connoisseurs food & beverage tubing that is assembled in the MoreBeer! Pro production shop in Pittsburg, California. The options above are already assembled and ready to shop. Novaflex is a special kink and crush resistant suction & discharge rubber hose, designed for those demanding applications requiring a product that meets 3-A (cert# 1803), FDA & USDA standards. This tube is for non-oily applications. Designed to meet the temperatures and chemical resistance associated with "cleaning in place" systems. The ultra smooth microbe resistant tube is built on special stainless steel mandrels for cleanliness. The ForgeFit barbed connector and crimp sleeve system are designed to provide a long life and easy to clean hose connection. The long barb and the long sleeve provide a secure crimp without crushing the hose. Triple banding can slip or damage the hose during installation and has sharp edges. The ForgeFit hose barb skips the first barb to provide a gapless and smooth transition to the tubing to make it easier to keep clean. Our barb has a stop to ensure the hose does not creep closer to the clamp in service. Don't forget to add hose bumpers to your order to protect your investment! The ForgeFit® Silicone Hose Bumper is designed to protect your hose ends by absorbing the impact of the hose end hitting the floor when it's dropped. The unique built in handle makes it easier to grab and saves your back. Novaflex Construction: Tube: White Chlorobutyl Reinforcement: Multiple plies of polyester tire cord & dual monofilament helix Cover: Gray EPDM abrasion resistant Temperature Range: -40° to 240°F (CIP to 248°F) Not for continuous steam service in. mm ID 1 25.4 OD 1.64 41.65 Bend Radius 3.5 88.9
Inline mesh screen filter to pre filter liquids before passing through a pump. Will remove large particles and protect the pump mechanisms from contaminants. Features 3/4 inch barbs on the in and out sides. The clear plastic cover is removable for cleaning or replacement of the screen.
Replacement body O-ring for Euro 30 pump. This O ring is slightly smaller than the O-Ring in the head of the PMP530 & PMP535.
In Documents Tab:
Position: 6
EnoItalia Item #: G2151
Get that eye-catching cascading effect by serving your Stouts & Porters with a nitrogen tank filled with beer gas mix!
Serve still beverages on draft with pure nitrogen or argon—serving still bevs with CO2 will lead to carbonation over time
Dual high-pressure and low-pressure gauges to easily reference cylinder pressure and output pressure
CGA580 inlet compatible with standard US nitrogen and argon tanks
Made in the USA. Taprite is one of leading manufacturers of gas regulators and draft dispensing equipment
One-way shutoff valve outlet protects your regulator from backflow and can be turned on/off to stop gas flow without needing to close your tank
This Taprite Nitrogen Regulator will allow you to add Nitro-Draft capability to your home dispense system!
Use this dual gauge nitrogen regulator to connect a tank of Beer Gas mix (70% Nitorgen/30% CO2) to your keg for an authentic nitro-pour! Traditionally used for stouts and porters, a nitro pour is becoming popular with more and more beer styles, lending its signature creamy mouthfeel and head to the beer. An amazing upgrade to any brewer's draft system.
Made in the USA by Taprite. 5/16" barb.
With your own Nitrogen tank, you can add Nitro-Draft capability to your Home Dispense System!
Serve beer on Nitro! The best way to pour your favorite stouts and porters!
Made from high-quality aluminum that will never rust like steel tanks
Fill with Beer Gas Mix to get that alluring, cascading pour famously associated with Guinness
CGA580 valve pairs with standard US-style nitrogen & argon gas regulators
KOMOS® offers a full suite of first-rate draft products and draft fittings—from kegs to faucets and everything in between!
Use pure nitrogen to serve still wine, cold brew coffee, Sangria and premixed cocktails on draft
Brand new aluminum 22 cubic feet Nitrogen tank made from high strength aluminum alloy and high quality CGA580 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It can be filled with compressed (liquified) Nitrogen, Argon, or Beer Gas Mix (70% Nitro/30% CO2).
Fill with beer gas mix (70% Nitrogen/30% CO2) for dispensing beers "On Nitro". Using 100% Nitrogen is also the recommended gas for dispensing cold brew coffee, wine, or even Sangria and premixed cocktails on draft!
Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder.
Tanks should always be stored in an upright position.
Features:
Made from corrosion resistant, engineered Aluminum
Brushed finish
Thick, durable cylinder walls
DOT approved
New high quality CGA-580 valve
Light weight compared to steel tanks
Rated to 2216 PSI service / 3360 PSI test pressure PSI (allowing for Nitrogen fill)
Can also be filled with Argon or Beer Gas Mix (Nitrogen/CO2)
NOTE: You will need at Nitrogen/Argon Regulator to go with this tank, a standard CO2 regulator will not work.
Connect these pumps up to an air compressor and you get a gentle transfer solution at a very reasonable price. Flow rates are variable by regulating the inlet air pressure at the compressor and/or by applying back pressure with a ball valve.
We offer two styles of this pump, with either a polypropylene body or stainless steel body. Both models feature a Santoprene diaphragm. The Polypropylene pumps are available in 3/8", 1/2" and 1" Female Pipe Thread inlet / outlet; the Stainless Steel pumps are available in 1/2" and 1". Stainless Steel adapters to common barb sizes and to Tri-Clover style fittings are available. 1" models offer a Max Flow Rate of 53gpm and a Max Inlet Pressure of 120psi (8.3bar). Please see the specs below for information on this particular model.
Manufactured by ARO. Smaller and larger sizes are available, please call 1-800-600-0033 or e-mail support@moreflavor.com for more information.
Does not include air compressor or regulator
Specifications:
Maximum Air Inlet Pressure .............. 100 p.s.i.g. (6.9 bar)
Maximum Material Inlet Pressure ....... 10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure ................ 100 p.s.i.g. (6.9 bar)
Air Consumption @ 40 p.s.i. .............. 1 c.f.m. / gallon (approx.)
Maximum Flow Rate (flooded inlet) .... 10.6 g.p.m. (40.1 L.p.m.)
Displacement / Cycle @100 p.s.i. ......... 0.022 gal (0.083 lit)
Maximum Particle Size .................... 1/16" dia. (1.6 mm)
Maximum Temperature Limits ........... 35 to 150 F (2 to 66 C)
Noise Level @ 70 p.s.i., 60 c.p.m. ...... 72.7 db(A)
Dimensions .................................... 7 31/32" W x 9 5/16" H x 5 23/32" D
This stainless steel cart makes it easy to wheel around your pump and is small enough to fit into tight spaces. Comes with pre-drilled holes for mounting. Compatible with Euro 20 and Euro 30 flexible impeller pumps.
Flexible impeller pump for moving wine or juice Stainless steel pump head with 1.5" tri-clamp connections On/off switch for easy operation 4.4 gallons per minute flow rate Pre-wired with 110V plug Made in Italy by EnoItalia This version of the Italian-made Euro 20 features a pre-wired 110V plug. Unlike the 220V model, this pump is ready for use and does not require a plug to be wired to a bare cord. The Euro 20 is a great pump for smaller production. Featuring a SS head with 1.5” TC fittings, this flexible impeller pump is great for moving wine or juice. We have this pump set up with a forward and reverse on/off switch on the body, simplifying operation. This unit comes with mounting points for if you want to mount it to a cart or filler/filter. Features: Flow rate is 4.4 gpm Max Pressure: 46 PSI (3.2 BAR) 1.5" Tri-Clover inlet and outlet 110V single phase Pre-Wired Plug 0.5 HP motor 1.7 amps Recommended temperature range: 40 - 150°F (5 - 65°C) SS head w/ Flexible Impeller
Can be added to the PMP100 to slow down flow on command. Can reduce flow by up to 25% by taking liquid from the output and redirecting it back to the input. Also good if the pump is encounterin back pressure in your particular set up. Has 1.5" TC connection on both the in and the out.
Replacement air tubes for variable capacity tanks. 115 cm tube fits LA Inox 1850 Liter tanks.
Please note: These tubes are only compatible with Marchisio brand tanks. They will not work with Speidel or other brands of variable volume tanks.
Made to pair with the EnoItalia Lobe Rotor Pump, the optional receiving hopper can be used under a destemmer crusher to collect whole destemmed, or crushed grapes. Max capacity 50,700 lbs with destemmed grape, and 44,000 lbs with fermented grape. 220V 3 Phase 0.75 kW
Combines all the benefits and advantages of our best-selling rubber impeller Enoitalia Euro Pumps with inline volume measurement. This is a pump with a brain! Enter in the volume of wine you would like to pump and the EuroFill turns off when that volume has been pumped. With a built-in flow meter, PLC (programmable logic controller) and a touch screen this pump will reduce human error and make your cellar life a lot easier. Filling barrels, blending exact volumes of wine, and dosing larger tanks with specialized ingredients are a few of the most useful applications. You can also control pumping by time which can be useful for pump overs and cleaning solutions.
Includes a wireless remote control. Made by Enoitala, a pump specialist, in Tuscany Italy. Sold and supported in the USA by MoreWine!.
Unique Applications:
Know the volume pump during any transfer
Program an exact volume you want pumped
Easily create perfect blends
Fill barrels by volume (and then top off)
Can be used for all general pumping application
Features:
Rubber impeller pump with electronic speed control
Programmable Logic Controller (PLC) for manual or automatic operation
Endress induction flow meter
Programmable dosing, counting, and timer
Remote control
7" Touchscreen
Stainless steel control panel and trolley
Dry run protection
Pressure switch
Specifications:
Capacity: 0-1,373 GPH (0-5,200 L/h)
Max Pressure: 40 PSI (2.8 BAR)
1.5" Tri-Clamp Inlet/Outlet
220V, Single Phase
2.2 kW
Please note: the unit will arrive bare without a power cord, plug, or controls to power the motor on or off. You will need an electrician to wire the appropriate power cord and controls to the motor.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
Self-priming wine pump with variable flow control from 0 to 20 gallons per minute
Flexible rubber impeller gently pushes wine
Stainless steel pump head with 1.5" tri-clamp connections
Remote control operation with 40 ft. long cord
Stainless steel control box
Stainless steel rolling cart
Made in Italy by EnoItalia
This unit features a stainless steel control box not pictured in the primary image. Updated images coming soon.
The perfect pump for moving wine from one vessel to the other. These Flexible Impeller Pumps are controlled by a Variable Frequency Drive, allowing for wine or juice transfers as fast as 20 gallons per minute, down to a complete stop. A sturdy Stainless Steel cart with nylon wheels allows for easy manueverability in the winery, and a lifetime of use. The pump can be controlled from the panel itself, or remotely via the wired controller, giving this workhorse even more flexibility.
We worked for a year to develop this particular pump with Enoitalia of Italy. The value and price are really amazing. So much that we stopped making our own line of Chunky Pumps at the end of 2016. Enoitalia has been making pumps for decades and while they are excellent at destemmer crushers and other equipment, pumps are their core specialty. We will support the pump in the USA with common spare parts but we also have the backing and support of Enoitalia if anything was to go wrong.
Although the Euro 30 is self-priming, the pump should never be run dry.
Stainless steel head with flexible rubber impeller
Remote control with 40' cord included
VFD allows for flow rate from 0 to 19.8 gpm
Max Pressure: 40 PSI (2.8 BAR)
1.5" Tri-Clover inlet and outlet
220 v single phase Input voltage required (6.5 amp draw)
1.5 HP motor
Recommended temperature range: 40 - 150°F (5 - 65°C)
Handy SS trolley cart for easy movement around the winery
The pump is reversible and can be controlled from the panel itself, or remotely via the wired controller, giving this workhorse even more flexibility.
Please Note: This pump will NOT come with fittings. It will have 1.5" Tri Clamp ferrules, and the appropriate fittings can be chosen from YMANs below.
Wheeled crush pad pump rolls directly under the Jolly 40 or Jolly 60 Crusher Destemmer
Stainless steel construction throughout
Screw feed moves grapes to the elliptical must pump with 3" tri-clamp outlet
Up to 16,000 lbs per hour processing capacity
Made in Italy by EnoItalia
A 3-Phase Crush Pad Specific must pump that transfers crushed grapes from your Crusher Destemmer to your tank or bin. Entire pump is on wheels and will slide under the Jolly 40 or Jolly 60 Crusher Destemmer. Grapes would fall into the awaiting stainless hopper. Stainless screw moves grapes into the eliptical, paddle style must pump that then moves them through 3" tubing to final destination. Considered more gentle than using a rubber impeller must pump. Only available in 3 phase power.
Details:
Power: 2.5 HP Three Phase 220 v draws 4.7 amps
Capacity: 12,000 to 16,000 pounds per hour
Shaft Speed: 47-58RPM
Max Pressure: 7.2 PSI (0.5 BAR)
Out Let Barb: 3" Tri-Clamp
Max Discharge Height: 9 feet
Max Discharge Distance: 30 feet
Weight: 220 Pounds
Pump Body: Stainless Steel
Loading Hopper & Screw: Stainless Steel
Refillable automatic lubricator
Hinged discharge cone can be opened for inspection
Single speed pump
Please Note: This unit REQUIRES 220V Three Phase power and will not function on anything else. Please confirm that you have the proper power for this unit before purchasing, and plan to have a qualified electrician wire the necessary plug to the cord.
Self-priming flexible impeller pump with stainless trolley cart for moving wine or juice
Stainless steel pump head with 1.5" tri-clamp connections
On/off switch for easy operation
4.4 gallons per minute flow rate
Made in Italy by EnoItalia
The Euro 20 is a great pump for smaller production. Featuring a SS head with 1.5” TC fittings, this flexible impeller pump is great for moving wine or juice. We have this pump set up with a forward and reverse on/off switch on the body, simplifying operation.
Features:
Flow rate is 4.4 gpm
Max Pressure: 46 PSI (3.2 BAR)
1.5" Tri-Clover inlet and outlet
220V single phase Input Voltage Required
Bare Cord for wiring with the appropriate plug
0.5 HP motor
1.7 amps
Recommended temperature range: 40 - 150°F (5 - 65°C)
SS head w/ Flexible Impeller
Please Note: This item may come with a bare cord or with a European style plug. You will need a professional electrician to wire the pump with the appropriate plug.
Stainless steel pump with food-grade plastic impeller with for moving wine or beer
1.5" tri-clamp connections
13 gallons per minute flow rate
Made in Italy by Marchisio
This pump features a stainless body, housing, and bracket. It utilizes an impeller made from food-grade plastic. The impeller does not push air by itself so to prime it you unthread the priming nut on top of the filter housing and fill with water or wine. Comes with 1.5" T.C. inlet and outlet. Has a .8 hp motor and moves 13 gallons per minute with no head. Will pump up to a height of 70'. 110v. Overall dimensions are 14.5" L x 7"W x 7"H. Weighs 15.4 lbs. Optional by-pass can be installed to restrict flow up to 25%. This pump can handle some small solid particulate, such as grain particles, and is food grade up to 113° F.
Please note the instruction manual references 230V for the voltage, but these pumps are custom configured by the manufacturer in 110V.
