Up to 35% Off · Ends June 30
Everything On Sale
856 products marked down through the end of June. Shop by brand below or scroll the full lineup.
-
The FermWrap™ Heater | Fermentation Heater | 40 watts | 115V
Achieve consistent and optimal fermentation temperatures with the FermWrap Fermentation Heater. This flexible and easy-to-use unit wraps snugly around your fermenter, providing gentle and controlled heat. Use alone or simply plug into the 110V heatnig plug on most popular temp controllers Provides gentle, even heating with 40 watts spread over almost two square feet Keep your yeast happy and your ferment warm during those cold winter months with this flexible heater wrap! Don't be fooled by imitators and cheap knock-offs, this is the original FermWrap that has been produced by Fermentap for over a decade. Unlike those old heater belts, the FermWrap covers a wide area of your carboy or fermentation vessel, promoting an even heat distribution. Using tape to adhere, the FermWrap can be attached directly to your fermenter, or can be used to heat the space in a box (or refrigerator) that the fermenter is in. Depending on your configuration and insulation, you can increase the temperature of your ferment from 5-20°F. This differential can be increased by using the BrewBuilt™ Neoprene Carboy Sleeve. With 40 watts of heat spread over almost two square feet, it provides gentle, even heating. For more precise results, we recommend a temp controller and carboy thermowell. The controller will monitor the fermentation temp and only power on the FermWrap if the temperature drops below your set point. For the ultimate level of control, we recommend pairing it with the BrewBuilt CoolStix™ to provide cooling. With both accessories plugged into the temp controller, you'll get cooling or heating whenever you need it. Specs: 40 watts 115V 11" H x 25" W Item does not include carboy as pictured. Kegland Part number: KL0625
$32.99 $21.44
-
Stainless Hop Tube
This stainless steel hop tube is ideal for keeping kettle additions from clogging your pump or heat exchanger, and works perfectly for dry hopping in a keg or wide-mouth fermenter. Holds approximately 5 oz of pellet hops, allowing some space to permit full extraction of the hop oils. The stainless chain makes it the perfect partner to our Corny Keg Lid with Welded Tab. Hang the tube inside your keg for post fermentation hop, fruit, wood chip, or spice additions. When it's time to remove the hops/adjuncts simply pull the tube out. Works great for timing exactly how long your beer sits on the hops, oak, or other flavoring addition. 2.6" diameter 11.8" tall Made from 304 stainless steel Kegland Part Number: KL05210
$18.99 $16.14
-
KegLand Oxebar Mono PET Keg | Plastic Reusable Bottle | Cary Handle & Reusable Screw Cap Included | 1 Gallon | 4L
Oxebar Mono is a lightweight 1-gallon keg with high oxygen barrier properties compared to standard PET plastic Add the Ball Lock Adapter Tapping Head to easily pressurize and dispense at home or on the go Lighter than traditional glass growlers. Easier and safer to transport Made from Nylon impregnated PET for superior oxygen barrier Wedge seals on the optional Tapping Head and Ball Lock Caps eliminate points of oxygen ingress found where rubber is traditionally used Lower total oxygen pickup compared to a standard corny keg lid seal This 1-gallon keg is lightweight, compact and has high oxygen barrier properties with 3x better (meaning less) gas transmission than traditional PET grades of plastic making it suitable for beer storage or other oxygen sensitive carbonated and non-carbonated beverages. This product is sold with the PCO38 cap, however if you would like to dispense this product through a draft system, we recommend the use of the Ball Lock Adapter Tapping Head. The tapping head is sold separately and allows you to attach standard ball lock disconnects and pressure relief valve to the top of the keg. What is Oxebar Mono Oxebar Mono is a PET polymer blend that utilizes several polymers blended together to significantly improve gas barrier properties. When compared with standard PET plastic, Oxebar Mono is able to reduce oxygen ingress and CO2 loss so your precious beverage is preserved and shelf life extended by 3x. We recommend this product for beer storage of up to 6 months. Dimensions: Diameter: 6.1" (155 mm) Height: 12.7" (325 mm) Pressure Rating: 58 psi (4 BAR) Temperature Rating: 113°F (45°C) KegLand Part Number: KL2487 NOTE: Oxebar kegs are marked with a manufacturer’s “expiry date”. This does not indicate that the keg is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the keg be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the KG520 Tapping Head and D1072 Green PRV to perform the test. If you do not plan to pressurize the keg, the test is not necessary.
$12.49 $8.12
-
Stepless Clamp Tool
This purpose built clamp tool is the easiest way to fasten our stainless steel stepless clamps.
$10.99 $7.14
-
MaltMuncher 2 Roller Grain Mill | Cold Rolled Steel Rollers | Adjustable Gap Setting | 6 lb Hopper Capacity
Mill your own grains on brew day for increased freshness and higher efficiency! Adjustable gap setting allows you to fine tune your preferred crush level and adapt to the kernel size of different malts 12 TPI knurl to efficiently pull grain through rollers while leaving hull intact to form an excellent filter bed for sparging 2 roller mills are great "first mills" for homebrewers expanding their brew kit. Economical and gets the job done! Included crank handle can be detached to power the driven roller with an electric drill or motor Mill your own grains for ultimate freshness with the MaltMuncher two roller grain mill. Includes a 6lb hopper, adjustable rollers, and hand crank. The handle can be removed to use the mill with a drill. The MaltMuncher is backed by a one year warranty and is built to last with rollers made from cold rolled steel, a big upgrade over most entry level mills. The body and hopper is made from 6061 grade aluminum. The optional PPE base board is much stronger than comparable particle board or plywood bases and makes for a secure platform to set on a bucket. Do you love to build your own equipment? Make an amazing motorized mill with the optional MaltMuncher high torque motor designed to work with the MaltMuncher 2 roller and MaltMuncher 3 roller grain mills. Features: 6 lb hopper and crank handle Great for use with a power drill Cold rolled steel rollers sized at 5" long by 1.25" diameter Adjustable rollers at both ends to move the gap from .025" - 0.1" If motorized we recommend 200 rpm 12 TPI knurl to effectively pull grain through the rollers while still leaving the hulls intact to later form an excellent filter during the sparge 10 mm crank shaft KegLand Part Number: KL03254 Please note: This mill is designed for use with brewing grains only. It will not work for cracking whole kernel corn.
$131.99 $112.19
-
Hop Sock | Small Grain Bag | 6 in. x 31 in.
Suitable for both hops and steeping grains. We highly recommend using a steeping bag for hops to keep vegetal matter contained in the boil kettle and out of your fermenter. If you use a counterflow chiller or plate chiller for cooling, filtering hops is even more important as these devices can clog if too much hop matter passes through them. The hop sock does not have a drawstring. You will want to tie the end in a knot to keep it closed. Dimensions: 150 mm wide (5.9") 800 mm long (31.4") KegLand Part Number: KL01281
$1.79 $1.16
-
EVABarrier Double Wall Draft Tubing - 5 mm ID x 8 mm OD
If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 5 mm (13/64") ID size is perfect for draft applications where a longer beverage line is needed. We recommend using 10-12 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 5 mm (13/64") Outer Diameter - 8 mm (5/16") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. Kegland Part number: KL06231
$4.35 - $144.99
-
Stainless Barb - 1/2 in. x 1/2 in. Male BSP
Stainless steel barb fitting. 1/2" male BSP x 13mm barb (0.51"). KegLand Part Number: KL03629
$6.59 $4.28
-
Wort Aerator | Air Pump Kit | Aeration System w/ Filter & Diffusion Stone
Aerate your wort automatically with this complete aeration system. Includes compact air pump, air filter, diffusion stone, and EVABarrier tubing. This aeration system diffuses oxygen into your wort using the air around you, so there's no need to buy pure oxygen cylinders again and again. The down side is that aeration takes longer than oxygenation. Because the atmosphere is only about 20% oxygen, the diffusion stone must be left running in the wort for approximately 30–120 minutes (but even 5 minutes of aeration is better than shaking the carboy). The sterile filter will prevent contamination during this period, but you will need to monitor the fermenter periodically for possible over foaming. To clean your stainless stone, we recommend boiling it for several minutes and storing it in a zip lock bag between uses. It can clog easily with the oil in your fingers, so use gloves when attaching it to the tubing. NOTE: You will need to use hot water to soften the 4 mm x 8 mm EVABarrier tubing when attaching the stone. Needle nose pliers can help to widen the tubing, if necessary. Hose clamps won't be required once it's attached. You will also need to cut a short piece of tubing to bridge the connection from the air pump to the air filter and the air filter to the diffusion stone. You do not want the air filter to get wet or be inserted into your fermenter, so keep the air filter close to the pump. The sanitary air filter can last up to 1 year, but should be replaced if there are any signs of discoloration. Includes: CE Air Pump 15 micron sintered stainless stone with barb 0.2 micron autoclavable air filter Approximately 5 ft. of EVABarrier tubing (4mm ID x 8mm OD) KegLand Part Number: KL03926
$27.49 $23.37
-
AlcoEngine Copper Alembic Distillation Lid | 6mm Gasket
The Alembic Copper Domed lid will help you achieve a smoother, richer, sweeter tasting spirit by helping to remove unwanted sulfur compounds. The large copper surface area acts as a catalyst with distilling vapor to enhance and concentrate flavors and aromas during the distilling process. Primarily intended for use with the Copper Pot Still, but it can also be used with the Copper Reflux still if desired. Note: This lid uses a 6mm gasket to better fit the Gen 4 BrewZilla and Gen 2 DigiBoil. It is also backwards compatible with Gen 3 and older BrewZillas and Gen 1 DigiBoils. To improve the seal further, we highly recommend using the Adjustable Lid Clamps with the Distillation Lid if your unit does not have them. 9-1/2" Tall 12-3/8" Diameter. Please note that copper is a very soft metal and can be dented quite easily. Store and use with care. KegLand Part number: KL1589 Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States. It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA).
$120.99 $102.84
-
4 in. Tri-Clamp Lid with Ball Lock Posts, PRV & Floating Dip Tube
This stainless 4" tri-clover ball lock lid is a direct replacement to the lid that comes on our kegmenters. Installation Note: For best performance, ensure there is not an excess amount of slack when the silicone dip tube is installed and shorten it if needed. With the floating dip tube installed on your empty Kegmenter, you ideally want the dip tube to hang freely with just enough length for the end of the dup tube to touch the bottom of the keg.
$60.99 $51.84
-
Insulated Cooler Mash Tun | Hot Liquor Tank | 14 gal.
If you're ready to step up to all grain brewing, this converted insulated cooler works wonders as a mash tun! The 14-gallon size can hold upwards of 25 lbs of grain, so there's plenty of room for even the strongest 5-gallon beer recipes and is perfect for most 10 gallon batches up to 1.070 SG. Comes pre-assembled with stainless steel perforated false bottom, high temperature silicone tubing, and 1/2" female threaded ball valve. Pair the valve with the male threaded fitting (plus a little plumber's tape) that best suits your setup and you'll off and running. The cooler also works perfectly as a Hot Liquor Tank. Use with the false bottom in place, or simply remove it and keep it on hand in case you decide to use the cooler as a Mash Tun down the road. Two of these coolers plus the Fermentap Sparge Arm Assembly work perfectly as a gravity fed all-grain setup. To connect the cooler's ball valve to the sparge arm assembly, we recommend a 1/2" MPT x 3/8" Barb fitting and 3/8" ID silicone tubing. Plumber's tape will ensure you have a leak-proof connection between the barb fitting and the ball valve. Includes: Insulated beverage cooler Max Volume: 14.7 Gal (56 L) Stainless dome-shaped perforated false bottom High temperature silicone tubing Stainless 1/2" BSP ball valve External Dimensions: Approx. 19" L x 19" W x 22" H KegLand Part Number: KL04671 Please note: the mash tun may come with a little extra silicone tubing than what's needed. Check that your false bottom is sitting flat and in the middle of the cooler and cut off excess tubing if needed.
$175.99 $131.99
-
Dual Gauge Oxygen Regulator for Disposable Tanks
Infusing your wort with pure oxygen immediately before pitching yeast is the best way to get your fermentation started faster and finished cleaner. This dual gauge oxygen regulator is compatible with standard disposable O2 tanks and provides a higher level of control when pumping oxygen into your wort. Using the adjustment knob, you can dial in the psi of the gas leaving the tank, leading to more consistent results. We recommend oxygenating wort using a 0.5 micron diffusion stone. Instructions: Attach the regulator to your oxygen tank Turn the pressure up to 10-20 psi Immerse diffusion stone in wort for 1-2 minutes Please note: your wort must be chilled to yeast pitching temperature before adding oxygen. It is much more difficult for oxygen to dissolve into solution when the wort is still warm. Kegland Part number: KL02165
$43.99 $37.39
-
Compact Sanitary Filter
These 0.2 Micron Air Filters have a fine enough filter membrane that they can filter out microbes and bacteria. They can be used with any oil free air compressor such as a pond pump, or other type of pump. They can also be used as an airlock in the top of your fermenter or used to filter air going back into a cask when dispensing real ale. This filter is not suitable for liquids and should be discarded if it gets wet. Compatible with 4 mm ID EVABarrier tubing. You will need to heat up the tubing and use needle nose pliars to widen the inner diameter. No hose clamp required. Specs: 0.2 Micron Pore Size PE Membrane Suitable for 3/16" ID tubing KegLand Part Number: KL08587
$4.39 $2.85
-
EVABarrier Double Wall Draft Tubing | Transparent Red | 5 mm ID x 8 mm OD
Easily identify gas and beverage lines with color-coded options—LightShield Black for beverages, Transparent Red for gas EVABarrier's double-walled design with a proprietary inner polymer significantly reduces oxidation and CO2 loss, keeping your beer fresher for longer The ultra-smooth, nearly impermeable inner surface of the tubing prevents bacteria and microbes from adhering, ensuring cleaner beer lines The stiff yet pliable EVA outer barrier makes the tubing kink-resistant and ideal for use with push-in fittings like Duotight and John Guest Red is recommended for differentiating your gas lines, but the 5mm ID is the perfect size if longer 10-12 ft. beverage lines are needed Easily identify your gas and beverage lines with color-coded draft tubing. Transparent Red EVABarrier is recommended for gas lines while using LightShield Black for your bev lines, saving you a headache when your draft lines inevitably get tangled up in your draft system. The semi-transparent red outer barrier makes the tubing easy to recognize even with minimal light. If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. If you wish to use the tubing for beverage rather than gas, we recommend using 10-12 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 5 mm (13/64") Outer Diameter - 8 mm (5/16") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. KegLand Part Number: KL42741
$28.49 - $120.89
-
EVABarrier Double Wall Draft Tubing - 6.3 mm ID x 9.5 mm OD
If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 6.3 mm (1/4") ID size is recommended to be used as gas line or long draw beverage lines. If you intend to use it as beverage line, we recommend using 20-25 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 6.3 mm (1/4") Outer Diameter - 9.5 mm (3/8") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. Kegland Part number: KL06248
$6.10 - $142.34
-
Stainless Ball Valve for FermZilla - PCO 1881 x 3/4 in. Female BSP
This stainless ball valve has a PCO 1881 female thread on one side for attaching to the male thread on the FermZilla lid or collection container and a 3/4" BSP Female thread on the other side for attaching other fittings. The 20mm bore (approx.) makes it possible to perform low oxygen dry hopping through the ball valve.
$17.99 $15.29
-
KegLand Ball Lock Quick Disconnect (QD) | Gas In | Barbed
The most affordable ball lock quick disconnect we offer! White color easily identifies the QD for gas use 1/4" barb connection This white, gas-in quick disconnect comes with a barb for attaching to a beverage line, and its high quality construction creates a sturdy seal that won’t leak gas when in use. The barb measures 1/4 inch, so it is compatible with either 1/4 inch or 5/16 inch beverage tubing. Note: Sometiems ball lock fittings can be difficult to get fully seated on a Cornelius keg. We recommend using a quick spray of sanitizer solution to act as a lubricant and giving it a few twists while applying the ball lock. Kegland Part Number: KL02943
$6.59 $4.28
-
Carbonation Drops | 250 g | Approx. 70 Drops
Fast and easy carbonation for your beer or cider Avoid the tedious, sticky process of spooning sugar into every bottle Eliminate the risk of oxidizing your favorite brew that often comes with batch priming Skip the sugar mess and the tedious measuring. With carbonation drops, bottle conditioning your beer or cider is as easy as "drop, seal, and sip." They deliver the perfect dose every time, protecting your brew from the risk of oxidation that comes with batch priming. Dosage Rate: 12 oz Bottle - 1 Drop 22 oz Bottle - 2 Drops KegLand Part Number: KL38461
$5.49 $4.12
-
Reagent Bottle for Yeast Starters - 1000 mL
This is a super cool bottle for making yeast starter wort. Mix DME and water to make your wort and then boil in the microwave with the cap off. Remove from microwave, thread on the cap while still hot, and place in refrigerator. Store the wort till you need it. When you are ready to make a starter remove from refrigerator to warm up, pour into a sanitized flask, and add your yeast. Make multiple bottles all at once at store in your refrigerator until needed. This reagent bottle is made from durable borosilicate perfect for storing anything you need. Borosilicate is great because unlike ordinary glass it won't crack with rapid changes in temperature. KegLand Item Number: KL04022
$17.99 $15.29
-
Stainless Tri-Clamp | 1.5" T.C. x 1/2" BSP Female
1.5" tri-clamp with 1/2" BSP female threads. Made from 304 stainless steel. This adapts the beer-in for the Canular KEG500 to TC. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL25362
$16.49 $10.72
-
Polypropylene Graduated Cylinder | 1 mL Graduations | 100 mL
These Polypropylene (PP) Measuring Cylinders are virtually indestructible. When it comes to brewing and winemaking, these will serve you a lifetime of use. Long gone are the days of dropping your glass measuring cylinder when taking a hydrometer reading, not only leaving you with a mess to clean up but also the need to scramble for another vessel to take a reading. The measuring cylinder has a wide sturdy base with a 28 mm (1.1") internal diameter. Approximately 24 cm (9.4") tall with 1 mL graduations, ideal for hydrometers and alcometers. Polypropylene (PP) Is also acid and alkaline resistant, so it can also be used to measure a large range of chemicals. KegLand Part Number: KL04039
$4.99 $3.24
-
Drafto Kit for the Ultimate Growler
The Drafto Kit is a great addition to any Ultimate Growler (GL750) that allows you to pressurize and preserve your beer for longer. Never have your growler go flat again! It's simple and easy to use; just replace the the original cap on your Ultimate Growler with the Drafto Kit, attach a mini CO2 regulator, pressurize and serve. Note: Does not come with CO2 regulator or cartridge. They must be purchased separately. We suggest one of our mini CO2 regulators (KEG965A) and cartridge (KEG962) or (KEG96) and cartridge (KEG993). Please Note: This unit Should Not be used with unregulated CO2 sources. Kegland Part number: KL0429
$18.74 $15.93
-
Kegmenter Fermentation Keg - 1 bbl
It may just look like an oversized keg at first glance, but the 1 bbl Kegmenter can do so much more! These stainless steel vessels are perfect as a pressure fermentation vessel, storage brite tank, or even a large-batch home still. Welded tri-clamp openings offer versatility for rigging up this unit however you see fit. Large 4" tri-clamp opening at the top and two 2" tri-clamps ports at the bottom. The large 4" opening at the top makes it easy to get inside the keg for cleaning, and the 2" ports at the bottom can be fitted with valves, heating elements, or other TC accessories and fittings. The kegmenter is well suited for use as a fermenter, brite tank, or top-up barrel. The 1 bbl Kegmeneter comes with end caps and clamps to plug the bottom ports, and a pre-drilled 4" cap for the top opening with a stopper and airlock included. You also have the option to use the Ball Lock Post lid with floating dip tube, which can be used for pressure fermentations or transfers. Also a 4" x 2" TC reducer would allow for adding a Reflux or Pot Still for distillation. Also consider the Kegmenter Hop Bong Pressure Pack which allows for oxygen-free dry hopping and also features ball lock posts for Gas & Liquid. Specifications: Volume: 1 bbl (31 gal) Working Pressure: 3 bar (43.5 psi) Made from stainless steel 41" H x 15.5 Ø Kegland Part number: KL04541
$499.99 $424.99
-
Vacuum & Pressure Relief Valve - 1.5 in. T.C.
This 1.5 in TriClamp pressure and vacuum relief valve is a great way to protect your tank. It will relieve pressure over 1.5 BAR but will also let in air if the tank is a vacuum inside to prevent the tank from imploding. Features: Relief pressure: 1.5 BAR (22 psi) Allows pressure in during a vacuum 1.5 in TC Kegland Part Number: KL01823
$109.99 $71.49
-
Push-In Pressure Gauge (0-150 psi)
The Push-In Pressure Gauge comes with an 8 mm (5/16 in.) barb, specifically designed to be compatible with 8 mm Duotight fittings. The dial face is triple-scaled to read in psi, bar, and kPa. 8 mm (5/16") push-in barb Rubber coated to protect gauge 0-150 psi / 0-10 bar / 0-1,000 kPa Kegland Part number: KL07696
$9.89 $6.43
-
Stainless Steel False Bottom Kit - 11.8 in.
This domed false bottom works great with most 10 gallon insulated cooler mash tuns or kettles with a similar diameter. The dome shape design adds strength so it can handle a heavy load of grain. Comes with 13 mm (.51") barb which is perfect for 1/2" ID silicone tubing. Made from 304 stainless steel. 30 cm (11.8") diameter. KegLand Part Number: KL01250
$43.99 $28.59
-
Kegland CO2 Cartridge - 74 g
These cartridges give the oomph to your mini-regulator dispensing unit! Perfect for dispensing your beer on the go. One canister will push between 1-4 Cornelius kegs, depending on how it is used and the CO2 consumption required. With the 74g adapter piece, these cartridges can be used with the KegLand Core 360 Mini Regulator or Torpedo Mini CO2 Regulator. 5/8-18 UNF threading Kegland Part Number: KL16889 Please note: due to air shipping restrictions, this product is only eligible for ground shipment within the contiguous United States.
$12.99 $11.04
-
MaltZilla Grain Mill - PPE Base Board
This premium Polypropylene Base Board is for the MaltZilla Motorized Grain Mill. Perfect for slotting over a food grade bucket, or building your own little shelf on wheels. Board Dimensions - 17.75" x 13.5" x 3/8" Kegland Part Number: KL17077
$21.99 $18.69
-
KegLand MKII Magnetic Drive Pump | Inline Pump Head | Stainless Steel | 5 GPM | 25 Watt
Magnetic drive enables you to slow down the flow without damaging the pump—just add a ball valve to the outlet! T.C. connection allows the pump head to be oriented at any angle in a full 360-degrees Pull ring PRV at the pump outlet makes it easy to purge air and prime the pump before each use Inline flow path for smooth integration into your brewery while keeping your tubing lines tidy Stainless steel head with 1/2" threaded ports to attach your preferred fittings—tri-clamp, quick disconnect, camlock, and More! The best-selling MKII Magnetic Drive Pump now available with a major upgrade! This unit comes standard with an inline stainless steel pump head that installs on the pump body with a 3" tri-clamp. Compared to the standard "center inlet" pump head, the "inline" flow path can make it much easier to integrate into your brewery and keep your brewing hoses tidy. At the outlet of the pump, there is a very handy pull ring PRV that allows you to bleed liquor or wort from the pump head to release trapped air and prime the pump. And with the 3" T.C. connection, not only do you have a full 360-degrees to orient the pump head any which way, cleaning the pump after use could not be easier—just pop off the tri-clamp, wash out the pump head, and clamp back on. The MKII is a perfect pump for your system and comes highly recommended for brewers stepping up to all-grain brewing. Rather than schlepping heavy kettles filled with hot liquor or wort around your brewery, or awkwardly stacking them into a 3-tier gravity setup, allow this handy pump to move liquid from vessel to vessel while everything remains in place. The magnetic drive allows you to slow down the flow without damaging the pump. This can be done by attaching a ball valve to the outlet side of the pump, and then you simply open or close the valve to control the flow rate. The pump itself is not self-priming, but priming is super easy thanks to the pull ring PRV which will help ensure the pump head is full of liquid and trapped air is released before powering it on. Tri-Clamp Pump Head The T.C. pump head can be removed quickly and easily using the 3" tri-clamp. This means no drivers or power drills are needed to back out the six Phillips head screws that mount the pump head on the standard version of the MKII. Whip the head off in a flash to clear out spent grain, hop material, or clear a blockage. Attaching the pump head with a tri-clamp also allows the head to be rotated at any angle in a full 360-degrees. This makes it easy to configure the plumbing to your unique brewery setup. Inline Design An "inline" pump head simply means the input and output are on a straight horizontal line with one another which can make it easier to integrate into your brewery setup. If you're using a 3-vessel horizontal system, the inline pump head will make it easier to keep your hoses neat and tidy compared to pumps heads with a center inlet. PRV Purge Valve The corny keg style PRV will make priming the pump a breeze. Simply let bleed the pump head to purge air out before turning the pump on and you'll avoid any cavitation issues. The PRV also acts as a safety so you do not over pressurize your pump head or brewery system. 304 Stainless Steel The entire pump head is made from 304 grade stainless steel so it's highly resistant to chemicals, heat, and physical abuse. The 1/2" BSP threaded ports can be used to attach barbs, quick disconnects, camlocks, tri-clamp adapters, or any other 1/2" fittings you prefer. Features: 110V / 60hz Max Head: 11.15 ft. (3.4 m) Max Flow: 5 Gal/min (19L/min) Max Temperature: 248°F (120°C) 360° rotatable stainless steel pump head 1/2" BSP ports Water resistant casing (not waterproof) KegLand Part Number: KL27236 If you're brewing on a budget and want the most affordable pump possible, check out the standard model MKII pump. This has been our best-selling pump for years and you can always upgrade it down the road with the standard stainless center inlet head or inline stainless tri-clamp head.
$164.99 $140.24
-
KegLand Quick Swivel Connector | 1/2" x 1/2" Straight Barb
High temp silicone grip provides a cool touch even with hot liquids! Ribbed grips allow quick comfortable tool-free operation Fits all male 1/2" NPT and BSP fittings 1/2" stainless steel barb tail The KegLand Stainless Steel Quick Connectors come with a heavy-duty silicone grip guard allowing comfortable and quick tool-free operation. These are ideal for the BrewZilla & DigiBoil ball valves, 25-Watt MKII Magnetic Drive Pump, or any 1/2" NPT or BSP connection. Specs: Stainless steel and silicone construction Silicone O-ring seal is retained for perfect positioning but is easily cleaned or replaced 1/2" (13mm) stainless steel barb tail with 3/8" (10mm) ID bore KegLand Part Number: KL31639
$6.59 $5.60
-
Red Reaper Counterflow Chiller | PEX / Copper Wort Chiller | 3/8" Barbs | 9.5mm Duotight Compatible
Counterflow design provides rapid, single-pass wort chilling Larger flow area minimizes hop clogs compared to plate chillers 9.5mm Duotight compatible inlet/outlets allow for quick and easy hose connections Durable PEX tubing resists high temperatures and pressures, extending the chiller's lifespan Tired of slow, inefficient wort chilling? Meet the Red Reaper Counterflow Chiller, your ultimate brewing ally. This isn't just another chiller; it's engineered for speed, durability, and hassle-free brewing. Unleash Rapid Cooling with Superior Design: Robust PEX/Copper Construction: Unlike standard clamped connections, the Red Reaper boasts PEX tubing swaged and soldered directly to the copper wort pipe. This innovative design guarantees a leak-proof, high-pressure connection, ensuring your cooling water stays where it belongs. Lightning-Fast Duotight Compatibility: Seamlessly connect your hoses and camlock fittings in seconds with the 9.5mm Duotight compatibility. Brew more, fuss less. Add the Duotight Push-In Thermowell Tee to add a thermometer to your wort out line. High-Efficiency Counterflow Design: Featuring an internal copper tube for wort circulation and an outer chamber for counterflowing cold water, the Red Reaper maximizes heat transfer for rapid chilling. Experience the power of single-pass cooling from boiling to pitching temperatures. Clog-Resistant Flow: Enjoy the benefits of a plate chiller's efficiency with a larger flow area that minimizes hop clogs. Built for Performance and Longevity: The Red Reaper utilizes the same pressure and temperature-resistant PEX hosing trusted in professional plumbing, offering exceptional flexibility and durability. We recommend recirculating your last 15 minutes of boil through the Red Reaper to sanitize it before chilling with cold water. Easy Cleaning and Maintenance: For optimal cleaning, circulate hot PBW for a minimum 5-minute contact time. Alternate flow direction for thorough cleaning, and rinse with water at the same temperature. Important Care Instructions: Avoid Sunlight: Prolonged exposure to sunlight can degrade the PEX tubing. No Acidic Cleaners: Do not store with StarSan or other acidic products, as they can damage the copper. What is PEX? PEX (cross-linked polyethylene) is a flexible, durable plastic tubing used as a reliable alternative to traditional copper or steel plumbing. Choose Your Fittings: The Red Reaper comes with bare, 3/8" barbs that you can simply clamp your tubing onto. However, we recommend using 9.5mm Duotight x 1/2" male thread adapters which will allow you to convert to your preferred fittings for the water and wort lines -- Camlock, Garden Hose, Tri-Clamp, Quick Disconnect (QD), etc. Specifications: 18.3 ft. Length 3/8" barb inlet/outlet 9.5mm Duotight compatible Rubber feet Hinged hanger (for BrewZilla handles) KegLand Part Number: KL3835
$172.99 $129.74
-
EVABarrier Double Wall Draft Tubing | LightShield Black | 4 mm ID x 8 mm OD
Easily identify gas and beverage lines with color-coded options—LightShield Black for beverages, Transparent Red for gas EVABarrier's double-walled design with a proprietary inner polymer significantly reduces oxidation and CO2 loss, keeping your beer fresher for longer The ultra-smooth, nearly impermeable inner surface of the tubing prevents bacteria and microbes from adhering, ensuring cleaner beer lines The stiff yet pliable EVA outer barrier makes the tubing kink-resistant and ideal for use with push-in fittings like Duotight and John Guest 4mm ID size is optimized for home draft systems with short 5-6 ft. draft lines Easily identify your gas and beverage lines with color-coded draft tubing. LightShield Black EVABarrier is recommended for beverage lines while using Transparent Red for your gas lines, saving you a headache when your draft lines inevitably get tangled up in your draft system. LightShield Black also works perfectly for hydroponic systems as it will block UV and discourage algae growth. If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 4 mm (5/32") ID size is perfect for homebrew draft applications where only a short beer line is needed. We recommend using 5-6 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 4 mm (5/32") Outer Diameter - 8 mm (5/16") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. KegLand Part Number: KL42765
$18.52 - $113.09
-
Stainless Ball Valve - 1/2 in. BSP Full Port
304 grade stainless steel ball valve. Full port for maximum flow rate. 1,000 psi rating for water, oil, or gas. 1/2" BSP female threads at inlet and outlet. KegLand Part Number: KL03681
$16.49 $10.72
-
Digital Oven Thermometer
Like many thermometers that were built for cooking and food processing, we find this digital oven thermometer to be just as useful for brewing applications. The cable allows you to place the temperature probe where needed and view the temperature reading from a convenient location. Especially helpful if your mash tun or hot liquor tank sit high up on a tiered gravity system. It also has a programmable alarm for when you hit your temp and a timer function you can use to track your mash progress or boil additions. Please note: the cable attached to the probe is not waterproof so be careful to not let it be fully submerged. If this does occur and your readings are off, you can place the probe in the oven (leaving the plug outside) and bake for 1 hour at 375°F to boil the moisture out of the probe. Broad temperature operating range 0-250°C (32–482°F) Temperature display resolution 1 degree C Timer range 99 min 59 sec Timer alarm function High temperature alarm function Celsius and Fahrenheit display option Battery operated 1xAAA
$12.49 $10.62
-
Gas Manifold - 1/4 in. (Aluminum)
Manifolds are a great way to have one CO2 tank supply multiple kegs. This manifold is made from aluminum, brass, and stainless. It also works up to 100 psi and includes 1/4 in ball valves with built in check valves. Another ball valve can be added to the end of the manifold for an additional gas line. Multiple manifolds can be linked up with a 1/4" nipple (D1820B). Features: 1/4" BSP ball valves 1/4" barbs Rated up to 100 psi Screw holes for easy mounting Optional additional port on the end SKU Overall Length D1802 5-1/2 in. D1807 7-3/8 in. D1811 9-5/8 in. D1813 11-1/2 in. D1816 13-1/2 in. The above measurements are from the tip of the brass barb to the plug on the opposite end. Each manifold measures approximately 3.5" from the mounting holes to the tip of the valve. Kegland Part number: KL02554
$17.22 - $41.24
-
Carbonation and Line Cleaning Ball Lock Quick Disconnect (QD) Cap - Stainless - Duotight Compatible
This stainless steel ball lock cap features soda bottle threads, allowing you to convert a 1 or 2 liter soda bottle into a convenient travel growler. The ball lock is compatible with both gas and beverage disconnects, so you can charge the PET bottle before you leave the house and dispense on the go. Use the Duotight compatible stem to connect a 8mm or 9.5mm reducer, then attach EVABarrier draft line to serve as your dip tube and you're all set! These caps also work great for quickly and conveniently cleaning your draft lines. Mix up a small batch of line cleaning solution in a soda bottle, attach the ball lock cap, and then connect it to your beverage line. Place a bucket below your tap to catch the cleaning solution and open your faucet. Then simply turn the bottle upside down and squeeze it to push solution through your line and out the faucet. You can also choose to pressurize the bottle first, but squeezing the solution through is just as effective. Fermenting with the FermZilla? This is ball lock fitting is also compatible with the FermZilla Collection Container. If you use the collection container to add dry hops, attach one of these caps and you'll be able purge the container of oxygen before opening the dump valve to introduce the hops. Attach some tubing and diffusion stone and you can oxygenate your wort through the collection container as well! Features: 6.5mm Duotight Compatible Liquid and Gas Ball Lock Compatible Disassembles for Easy Cleaning Made from Stainless Steel 28mm PCO 1881 Threads Please note: The threaded section of the bottleneck must be at least 1/2" long to form a seal. These caps are not compatible with the KegLand 500mL PET Bottles. Kegland Part Number: KL20435
$15.49 $10.07
-
Temp Twister Lid for Bucket Buddy Fermenters | 35L
This flat lid with pre-drilled holes allows you to easily add a Temp Twister Cooling Coil to your 35L Bucket Buddy fermenter. It also has holes for your stopper & airlock (included with the Bucket Buddy) as well as a Thermowell so you can control the circulation of cooling solution with a Temperature Controller. The lid is also compatible with 35L BrewZillas and DigiBoils. If you're fermenting in the Bucket Buddy with built-in heating element, we recommend plugging the unit into the heating outlet of your temperature controller and leaving the power switch turned on. This will allow the temp controller to provide power to the unit only when heating is needed and it will cut the power as soon as you're back to your set temperature. Using the Bucket Buddy's controller to maintain the heating set temp and using a separate controller to maintain the cooling may result in heating and cooling cycling at the same time. NOTE: The pre-drilled holes are meant for specific sizes of Duotight bulkheads and the stopper included with the Bucket Buddy fermenter. All holes need to be occupied in order to protect your fermentation from outside contaminants. Depending on the placement of the Temp Twister, you might need to shorten the inlet/outlet tubes on the outside of the fermenter using a Pipe Cutter. Lid only. Other accessories must be purchased separately. You Will Also Need: Temp Twister Cooling Coil FermZilla Thermowell Temperature Controller KegLand Part Number: KL28103
$38.49 $32.72
-
Replacement PRV | Pull Ring Pressure Relief Valve | Yellow | 17 PSI
Corny keg style pressure relief valve rater to 17 PSI Lower the blow off pressure of kegs, regulators, fermenters, etc. for added operating safety Replacement pressure relief valve rated to blow at 17 psi. This corny keg lid style PRV can be used with a range of products including kegs, FermZilla conicals, KegLand kegmenters, and KOMOS CO2 regulators. If you don't intend to ever exceed 17 PSI with the product you're using, installing the Yellow PRV will help ensure you don't over pressurize. NOTE: This is a safety device designed to release pressure at the approximate rated pressure. This is not intended to be used as a Spunding Valve. KegLand Part Number: KL22569
$7.69 $5.00
-
KegLand Quick Swivel Connector | 1/2" Elbow Barb
This elbow barb makes it easier to route lines and avoid kinks in your tubing. Commonly used for pump inlet/outlets, fermenter blowoffs, or gravity fed transfer lines. Quick Swivel Nut sold separately. Specs: 1/2" (13mm) OD x 1/2" Quick Swivel Nut compatible end Stainless steel KegLand Part Number: KL31660
$7.69 $6.54
-
HIZO G14 Pizza Oven | Gas Powered Pizza Oven | 14" Ceramic Pizza Stone | Stealth Black
The HIZO G14 Portable Gas-Fired Pizza Oven is the perfect no-hassle solution to cooking the best homemade pizza outdoors Fast. Heats to 932°F and cooks a pizza in 1 to 2 minutes Easy. No assembly required. Built-in gas ignition and adjustable heat control dial for temperature control Portable. Retractable legs and optional carry bag make it easy to transport and set up—just click the switch and start cooking 14" is the perfect size. 12" ovens are too small and 16" ovens are oversized and twice the price. Making homemade pizza in your kitchen oven is a tasty and rewarding endeavor, but nothing matches the performance and results you get from a purpose-built pizza oven. Kitchen ovens generally max out around 550°F whereas pizza ovens can reach as high as 1,000 degrees. The ideal way to cook pizza is quickly and at very high temperatures in the 800-900°F range, so if you want to take your homemade pizza game to the next level, a gas-fired pizza oven is the way to go! The HIZO G14 Pizza Oven is propane powered and ready to use straight out of the box with no bolts or tools required for assembly. Complete with dialed control and gas igniter included as standard—no batteries or matches required! Setup and packing away couldn't be easier thanks to the four stable folding legs. Includes: HIZO G14 Pizza Oven Liquid Propane hose and regulator Dual Scale Temperature Gauge: 32°F - 932°F (0°C - 500°C) Ceramic Pizza Stone: 14" x 14" x 3/8" Recommended Accessories: Waterproof Carry / Storage Bag (FPE202) Infrared Laser Thermometer (MT401) 12"or 14" Perforated Pizza Peel (FPE205 / FPE206) 8" Round Pizza Spinner (FPE204) 4" Pizza Cutter (FPE203)
$229.00 $171.75
-
Ball Lock Adapter Tapping Head for Sanke Kegs
If you like serving out of commercial kegs but prefer the ease of using ball lock fittings in your draft system, this adapter is for you. Instead of buying additional keg couplers and beer thread to ball lock adapters, you can use this tapping head to go straight from sanke keg to ball lock. To install, remove the keg spear, place the gasket on the keg ferrule with the beaded side facing up, attach the silicone dip tube and place the tapping head on the ferrule, then secure with the 2" tri-clamp. Be sure to always depressurize the keg before removing the tapping head. Includes: Ball Lock Post Lid 2" tri-clamp Single-side beaded tri-clamp gasket 60 cm silicone dip tube (23.6") Red 2.5 bar PRV (36 psi) KegLand Part Number: KL10610
$65.99 $49.49
-
High Temp Silicone Tubing | Reinforced | 7/8" ID
Reinforced silicone tubing offers higher temperature tolerances and chemical resistance while remaining flexible and easy to handle. Ideal for both cold side and hot side processes and high-pressure applications. Although braided, the tubing remains transparent to allow you to visually inspect the flow of liquids. The tubing inner diameter is slightly undersized at 22mm or 0.86". 0.86" (22mm) inner diameter 1.25" (32mm) outer diameter Odorless, tasteless and inert Polyester heat resistant fiber reinforcing braid Good electrical and weatherability properties Resists UV, Ozone, gases, and moisture Working Temperature: -76°F–500°F Working Pressure: 0-150 psi KegLand Part Number: KL25294
$96.99 - $227.79
-
KegLand Ball Lock Quick Disconnect (QD) | Flow Control Beverage Out | Stainless Steel | Flared
Control beverage flow as liquid leaves the keg—replaces the need for flow control faucets or compensators downstream Perfect for mobile draft applications when you can't balance your lines on the fly Made from stainless steel for high-durability Black ring above the outer bushing to identify the QD for beverage use Compatible with all ball lock style homebrew kegs 1/4" flare thread connection Pick up this Flow Control Ball Lock Disconnect and stop banging your head against the wall trying to balance your draft line. We're all after the same thing -- the perfect pour -- but balancing beer lines can be a daunting task. You do the research and crunch the numbers, choose the right inner diameter line, cut it to the ideal length, only to spend your evenings dialing your regulator setting back and forth like a turtle-necked safecracker. This stainless steel flow control disconnect will eliminate the guess work and fast track you to perfectly pouring beer. Flow control faucets are a popular option but they're inherently flawed due to the point of restriction being at the very end of the beer line. The flow control apparatus inside the faucet causes turbulence, which leads to foaming and carbonation coming out of solution prematurely. Flow control disconnects on the other hand restrict the flow before the beer enters the beer line so the head pressure created by the beer line keeps the carbonation in solution. Another advantage of FC disconnects is that you don't have to rely on a small inner diameter or long line length to apply flow resistance. In fact, even in the fully open position the disconnect will provide some inherent flow resistance, so you should use a shorter line than the 5-6 ft. length that is typically recommended. This makes the flow control disconnect ideal for dispensing beer on the go where you might have a picnic tap with a short line or a disconnect faucet adapter with no line at all! Please note: make sure your keg post o-rings are in good condition before using this fitting. If they are overly worn and you are not getting a good seal, replace the post o-ring then re-attach the ball lock fitting. Kegland Part Number: KL09041
$38.49 $32.72
-
Perforated Pizza Peel | Square Peel | 12"
The quintessential tool for launching your pizza and removing it from the oven Rather than using a pizza spinner, the square peel can be used to remove the pizza while cooking and rotated by hand Perforations allow excess flour to fall off the pizza base so there's less chance of flour burning and smoking up your oven Perfectly sized for HIZO Pizza Ovens The main purpose of a perforated pizza peel is to get rid of excess flour from the pizza base. But why do you want to get rid of the flour? When you’re baking pizza on hot stone or steel, you don’t want flour on the baking surface because it burns. Fine wheat flours that are most commonly used for baking pizza burn at fairly low temperatures. It’s this flour that causes trouble. Dusting your pizza peel with semolina flour, which can handle higher heat better, can also help. Burnt wheat flour will make the oven smoky and will result in more cleaning work when you’re done baking. The burnt flour tends to stick and can be a real pain to get rid of. Especially on an unglazed pizza stone. And if you’re not able to clean the stone properly, the flour can keep smoking next time you use the stone. Less Contact Surface – Less Sticking A perforated peel has a smaller surface that is in contact with the pizza dough. This means pizza is less likely to stick to a perforated pizza peel. The reason is that the larger the contact surface is, the more friction there will be between the peel and the pizza. And more friction means it is more likely to stick. A smaller contact surface also means that you’ll need less flour when you’re dusting the peel. As noted above, you want as little flour as possible in the hot oven. So in addition to removing more flour from the dough itself, the peel need less flour due to the holes. Perforated pizza peels are also lighter than solid pizza peels, due to less metal on the carrying surface. This will make it easier to use the peel. Less Condensation – Crispier Pizza Crust When you take a hot pizza out of the oven, you may have noticed that water sometimes is formed under the pizza. This moisture makes the pizza less crispy, or even soggy. Using a solid pizza peel may create condensation when the hot pizza meets the cold (room temperature) surface. This is mostly a problem with metal peels since hot air is trapped between the pizza crust and the smooth carrying surface. Condensation happens when this hot air is cooled down to a certain point (it’s dew point), and water drops are created. When you’re using a perforated pizza, on the other hand, you will experience less condensation. The reason is that the holes let the hot air escape through the peel. 12" Square x 31" Long Lightweight aluminum construction. Phillips Head screwdriver required for assembly. KegLand Part Number: KL21869
$54.99 $46.74
-
EVABarrier Double Wall Draft Tubing | LightShield Black | 6.3 mm ID x 9.5 mm OD
Easily identify gas and beverage lines with color-coded options—LightShield Black for beverages, Transparent Red for gas EVABarrier's double-walled design with a proprietary inner polymer significantly reduces oxidation and CO2 loss, keeping your beer fresher for longer The ultra-smooth, nearly impermeable inner surface of the tubing prevents bacteria and microbes from adhering, ensuring cleaner beer lines The stiff yet pliable EVA outer barrier makes the tubing kink-resistant and ideal for use with push-in fittings like Duotight and John Guest 6.3 mm ID size is recommended for long draw beverage lines 20-25 ft. in length Easily identify your gas and beverage lines with color-coded draft tubing. LightShield Black EVABarrier is recommended for beverage lines while using Transparent Red for your gas lines, saving you a headache when your draft lines inevitably get tangled up in your draft system. LightShield Black also works perfectly for hydroponic systems as it will block UV and discourage algae growth. If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 6.3 mm (1/4") ID size is recommended to be used as gas line or long draw beverage lines. If you intend to use it as beverage line, we recommend using 20-25 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 6.3 mm (1/4") Outer Diameter - 9.5 mm (3/8") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. KegLand Part Number: KL42772
$39.49 - $169.64
-
KegLand Stainless Steel Jockey Box | 4 Tap
Serve ice cold beverages from four independent kegs Customize with your preferred faucets and beer shank adapters to suit your specific needs Uniquely designed square draft coils and shank brackets keep the jockey box internals in place so you can easily dump your ice slurry after use The KegLand stainless steel jockey box includes all of the internals needed to serve four beverages on tap. The square shaped draft coils hug the sides of the cooler walls and are secured in place with specially designed shank brackets, allowing you to easily dump out your ice slurry after use without the internals of the jockey box spilling out. Faucets and tailpieces are not included so you can customize the box to your preferred setup. Recommended Accessories: NukaTap Flow Control Faucet (D15841) Duotight Adapter - 8mm x Female Beer Thread (DUO104) EVABarrier Draft Tubing - 8mm OD x 4mm ID (D1717) For Commercial Kegs: KOMOS D-Style Keg Coupler w/ Duotight Adapters (D1526) For Ball Lock Kegs: 8mm Duotight Ball Lock QDs - Gas In & Bev Out (DUO150 / DUO151) You will also need a CO2 cylinder and regulator, as well as a gas manifold or tee fittings to split your gas line to your four kegs. External Dimensions: 22.2" Wide (including handles) 15.9" Deep (including latch system) 16.1" High Internal Dimensions: 18.8" Wide 11" Deep 13.7" High (there is a slight 3/4" recess at the top to fit larger kegs/bottles)
$659.99 $494.99
-
Neoprene Insulating Keg Parka for Oxebar Mono PET Keg | 8L
Keep your beer colder for longer with the insulating neoprene material Prevent dings and scratches during transport with an internal bump cap Easily carry your keg using the removable shoulder strap The zippered design makes it simple to put on and take off Tailormade for the 8L Oxebar Mono PET Keg Keep your beverage colder for longer with the Oxebar Neoprene Jacket. This parka is more than just a cozy sleeve for your keg; it's designed with a rigid internal "bump cap" to prevent those annoying scratches and scuffs that can happen when your keg is being moved around. Made from durable neoprene, this jacket helps maintain the temperature of your beverage, whether you're taking it to a party or just keeping it chilled in the fridge. The Oxebar Neoprene Jacket protects your keg while helping your beer stay crisp and cold. KegLand Part Number: KL42895
$32.99 $21.44
You have seen 48 out of 65 products