Draft

The V10 stainless steel flow control faucet is designed and produced in Germany with some assembly completed in the United States. This faucet contains technology such as the "Closed Piston Chamber with Encapsulated Compression Spring" that allows for a perfect forward seal on the faucet, no beer trapped in dead space to cause the lever to stick, and the ability to push the faucet backwards for an extra creamy head. The compensator itself has an extra long cone for a wider range of compensation and designed to eliminate uncontrolled shifting of the compensator cone. This configuration features a black standard faucet knob, a polished stainless steel faucet lever, and a lever flow control adjustment system. Please note: The CM Becker X1 and V10 flow control faucets require a proprietary draft shank and will not work with a standard draft shank. Please select on of the draft shanks below to add to your order. 2.5" Chrome Exterior w/ Food Grade Liner (D12907) 2.5" Stainless Steel (D12908) 5-3/8" Stainless Steel (D12909) Features: Full length European Flow Control (completely control restriction at the faucet;no restriction line needed) Made in Germany and assembled in the USA! Features a built in “Creamer” function so you can put a fine cream head on your beer Used in restaurants and bars locally and abroad The faucet handle and draft shank in the example photo are not included.

Read more less

Stainless steel shank comes with a back nut, plastic collar, and a 3/16" tailpiece with hex nut and gasket. If desired, the barb can be removed and swapped for a different size or replaced with a Duotight x Beer Thread Adapter. This size of beer shank is a popular choice for building your own custom draft system. Typically installed in the door of a refrigerator or the wooden collar of a converted chest freezer. The shank’s listed size refers to the total length of threaded pipe. Approximately 1-1/8” are needed to account for the thickness of the finishing collar on the front and the space for the locknut on the back. Please take this into account when sizing the shank for your project. Installation Note: On a fridge there are generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 4-1/4" - Total Length (Tip to Tip) 3-1/8" - Shank Length (Without Nut & Nipple) 2-1/4" - Thread Length 1-3/4" - Pass Through Length 3/16" Nipple

Read more less

Due to high demand, some of these items are currently out of stock but available for pre-order. Please check status notes below when selecting a size option to see if it is In Stock or tagged as PreBook. We will automatically ship this to you when we receive more inventory.   Nothing looks quite as nice as beer pouring out of a shiny stainless steel draft tower. These are the same tower kits included with the KOMOS Kegerator. Includes EVABarrier draft tubing and Duotight push-to-connect fittings for easy assembly. These towers can be purchased without faucets, or you can choose your preferred faucets from the add-on options above. The tower is made from 304 brushed stainless steel, making them corrosion resistant while also looking great! Duotight Fittings & EVABarrier Draft Tubing Duotight and EVABarrier have revolutionized how you connect draft line, and our tower kits come standard with both. We love Duotight push-in fittings for their quick connection, reliable seal, and versatility. Setting up and connecting draft line has never been easier -- no more hose clamps or heating water to soften tubing! Each tower comes with Duotight fittings for the tower shanks and for splitting gas lines (double & triple tap only). We recommend adding Duotight fittings to use for your keg connections as well. Depending on whether you'll be serving from homebrew kegs or commercial sanke kegs, you'll need two DUO106 or two DUO104 per line. EVABarrier tubing has been engineered with protection in mind and is both PVC-free and BPA-free. This double walled tubing offers superior protection against oxidation, CO2 loss, and microbial growth. EVA tubing is the future of draft line for professional applications, and now your kegerator will feature the same first-class tubing. Includes: Stainless steel draft tower Stainless steel faucet shank(s) with Duotight tailpieces EVABarrier gas and beverage tubing Draft tower mounting screws Faucet wrench 1-3 Tap Tower Dimensions: 13.4 in. tall (without faucets) 3 in. tower diameter 4.4 in. base diameter 4 Tap Tower Dimensions: 15.75 in. tall (without faucets) 4.5 in. tower diameter Interior mounting holes (does not include bottom collar)   Please note: Perlick Flow Control faucets are not compatible with the included Intertap tower shanks.  

Read more less

EJ Beverage Ultra Barrier™ tubing from EJ Beverage is constructed of a unique compound that provides for an excellent alternative to PVC.  Advantages to this unique tubing are: PVC Free and BPA Free - containes no DEHP phthalates or other plasticizers Environmentally friendly production - does not emit dioxins Proven to have no significant impact on taste or flavor Extremely low extractables/leachables High flexibility Remains flexible at lower temperatures Ultra-low permeability Superior Barrier properties Temperature range of -40 to 125° F Working pressure of 52 psi Use this size for gas line applications. Also used for long draw beer lines over 25'. Technical Specifications: 5/16" line provides .40 lbs of restriction per foot. Ideally pounds of resistance should equal pounds of applied pressure. 5/16" line holds 1/2 of an ounce per foot. PVC Free.  

Read more less

This Duotight elbow fitting is compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07030

Read more less

This adapter can be installed on the Core 360 Mini Regulator from Kegland in order to use 74 gram CO2 cartridges. Use a crescent wrench to remove the stock adapter piece for 12 gram cartridges and simply screw in this adapter with 5/8-18 UNF female threading. Switching to 74 g cartridges will allow you dispense 1-4 Cornelius kegs, depending on how it is used and the CO2 consumption required. TR21-4 Male Thread x 5/8-18 UNF Female Thread Adapter only. Regulator and CO2 cartrdige sold separately. KegLand Part Number: KL2041

Read more less

This Duotight Bulkhead is the same one used for installing the Thermowell into the lid of the FermZilla. Allows you to add a bulkhead to just about anything that can then be connected to with EVABarrier 8 mm OD Tubing (D1717 / D1718) or 5/16" OD stainless or copper tubing. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. KegLand Part Number: KL14595

Read more less

This sleek black faucet handle blends a clean, professional look with simple functionality.     Standard size, 2.5" black cylindrical plastic faucet handle for beer faucets. 

Read more less

High performance primary regulator designed to handle the workload of dispensing from multiple taps without freezing up! Dual body regulator for setting independent pressure settings—ideal for serving two different beer styles with different optimum carbonation levels High-pressure and double low-pressure gauges to easily reference CO2 cylinder pressure and the two output pressures Pressure settings are easily adjusted by hand using the large plastic adjustment knob CGA320 inlet features a built-in gasket where the unit attaches to the CO2 tank—eliminating the need of replacing fiber washers with each tank swap Made in the USA. Taprite is one of leading manufacturers of gas regulators and draft dispensing equipment One-way shutoff valve outlets protect your regulator from backflow and can be turned on/off to stop gas flow without needing to close your tank When it comes to CO2 regulators, we’ve tried them all. This quality unit by Taprite is our favorite on the market. It’s no wonder this regulator is trusted by so many breweries and beer bars—it represents the best quality at a great price. This dual-body model allows you to send different pressures to two separate kegs from the same CO2 tank! The things you’ll love about this regulator are:  The large front knobs make pressure adjustment tool-free, easy & fast.  A built-in gasket where the regulator connects to the CO2 tank eliminates the constant replacement of fiber washers every time you change out your tank.  The barbed outlets feature one-way on/off valves which prevent backflow and protect the regulator’s internals.  The gauges are easy to read. The low pressure gauges read from 0 to 60 psi. The optional available gauge cage is the best on the market. This is the T752HP model, where the HP stands for high performance; it won't freeze up when multiple taps are running at once. Best of all is the consistent pressure regulation. With many regulators the pressure can 'creep' up over time. This unit holds the pressure rock steady. No drifting. Built by Taprite, an American company. 

Read more less

Perfect for home use with compact keg setups or on the go for mobile dispensing Compatible with both 16g and 74g CO2 cartridges Features a 6.35mm Duotight-compatible barb for fast, hassle-free keg attachments The Duotight Mini CO2 Regulator is a simple, affordable choice for mini kegs and Oxebar keg setups. This compact regulator is designed to work with both 16g and 74g CO2 cartridges, making it ideal for home use or when you're on the go. With the 6.35mm Duotight-compatible barb you can connect just about anything within a matter of seconds. Simply pair it with the 6.35mm Duotight Ball Lock QD for a quick and hassle-free connection to your kegs. Or, with the Duotight Reducer, you can adapt the regulator for use with the most common and widely used 8mm Duotight accessories. For additional protection against liquid backflow, you can integrate a check valve along with some hosing to safeguard your regulator. Please note if liquid enters the regulator, it's no longer functional. Be extremely careful with overfilling your kegs or tipping them over when the gas has run out. The regulator is capped at 30 psi to ensure you do not accidentally over carbonate or exceed your keg's pressure rating. The gauge reads up to 60 psi to account for potential heat expansion so that it does not break the gauge. Suitable Gas Cartridges: 16g Cartridge 6-pack (KEG993) 74g Cartridge (KEG969) KegLand Part Number: KL4200

Read more less

Replacement gaskets and o-rings for standard US keg couplers (D-Style) and European keg couplers (S-Style). Other than the probe washer, they use the same gaskets and check valves.

Read more less

Standard D-Style keg coupler works with virtually all American-made commercial beer sanke kegs Durable stainless steel construction ensures longevity and corrosion resistance for both the coupler body and keg probe Easy pull-style lever handle simplifies keg connection and disconnection for user convenience Includes 3/8" OD barb for gas inlet The KOMOS D-Style Keg Coupler is your reliable choice for dispensing standard American sanke kegs. Enjoy the peace of mind that comes with a robust, stainless steel construction, including the coupler body and keg probe, ensuring lasting durability and resistance to corrosion. The D-Style beer tap is the most commonly-used keg coupler in the U.S. The intuitive pull-to-engage lever handle makes connecting and disconnecting a breeze. An included 3/8" OD barb simplifies gas inlet setup, and the built-in pressure relief valve adds a layer of safety. This D-style coupler, the industry standard, is compatible with virtually all American-made commercial draft beer sanke kegs. The upgrade to 304 stainless steel from nickel-plated options provides a significant increase in lifespan, ensuring years of use. For a complete setup, tail piece, hex nut, and gasket for the beer outlet are sold separately and are available in a variety of sizes and styles.

Read more less

This stainless steel shuttle can be used to replace the TPV rubber NukaShuttle that comes standard in the NukaTap beer faucet. For users that prefer stainless internal mechanisms in their faucet. You will need to remove the bonnet piece at the handle, pull the handle out and then slide the shuttle piece out. Compatible with all NukaTap faucets. KegLand Part Number: KL35958

Read more less

Thick wall vinyl (PVC) tubing for gas and beer lines in keg systems. 5/16 in ID is the most common size used in commercial beer dispensing.  

Read more less

Easily attaches to any Intertap faucet. Just unscrew the standard spout and replace it with this growler spout. Then you'll have a 1/2" (13mm) barb on the end of your faucet. Compatible with Intertap and NukaTap faucets. Stainless Steel Construction Kegland Part number: KL01038  

Read more less

18 gram disposable Nitrogen cartridge. Often used to push wine, mixed drinks, coffee, or any other liquid where you do not want carbonation. Nitrogen, unlike CO2, will not dissolve into solution. Kegged drinks can be mixed up and will stay fresh for long periods of time. 5/8"-18 threaded neck.    Please note: due to air shipping restrictions, this product is only eligible for ground shipment within the contiguous United States.   

Read more less

Keep your counter or kegerator clean with this affordable wrap around drip tray. Fits well with 3" diameter towers, with room to fit snug up to the bottom collar. Removable grill for easy cleaning. This is a direct replacement of the drip tray that comes with our kegerators. Countertop design with feet Honeycomb pattern removable grill Half-moon cut out measures 4.5" across and 2-3/8" deep Dimensions: 15" L x 10" W x 0.75" H Made from ABS plastic Kegland Part Number: KL00192

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. The ultimate portable draft faucet! Compact & lightweight with all the advantages of a standard NukaTap forward sealing faucet Includes NukaTap Mini, Flow Control Ball Lock QD, Duotight Adapter, and Self Closing Spring Forward-sealing design prevents beer residue from gumming up the faucet Reduced first pour foam due to low thermal mass and conductivity Perfect for mobile draft, mini kegs, sampling from fermenters, and can even be installed on your kegerator or keezer Mini Design – Ideal Flow Rate for Small Systems Most conventional beer faucets are designed with 3/8" diameter spouts so you can pour a pint in just over 10 seconds. This type of flow rate is great for high turnover bars and commercial venues but isn't necessary or even desirable for all applications. For compact portable systems and home draft systems, a slower flow rate is easier to control and further reduces foaming issues due to the low liquid volume stored in the body of the faucet. The NukaTap Mini is also more ideal for pouring smaller doses. For example, cocktails where 5-8 oz of liquid is dispensed is difficult to control with a high flow rate tap. For portable systems, the NukaTap Mini with the Flow Control Ball Lock QD & Duotight Adapter assembly is small enough to literally put in your pocket, making it ideal for mini keg setups that you want to be portable or that you want to easily fit inside a domestic fridge where space is tight. Forward Sealing Forward sealing faucets are absolutely the way to go when it comes to beer taps. Old legacy taps still exist in the industry that are simply poorly designed. The issue with rear sealing faucets is that beer dries up on the internal piston. Aside from being unsanitary, as more and more beer dries up in these components the faucet can almost glue completely shut causing damaged seals or broken handles (this is particularly the case if it's left for some time to dry out with beer inside). These older legacy designs still exist probably due to poor education. The forward sealing designs do not have this problem and the tap drains out completely with no beer drying up on the mechanical moving parts in the same way. This makes the tap more sanitary and reduces maintenance. In many instances the price is similar so there is no reason to use a poorly designed rear sealing faucet. All NukaTap faucets are forward sealing. Laminar Flow Just like the NukaTap SS and NukaTap FC, the NukaTap Mini has been designed with laminar flow in mind. Laminar flow is critical for a beer tap as it means you will pour the beer with minimal foaming and a substantial reduction in wastage. Think about how many times a beer faucet opens and closes in its lifetime. 1,000 or maybe 10,000 times? Laminar flow saves wasted beer in excessive foam and the better laminar flow easily pays for itself in a reduction in lost beer. To use poorer designed faucets is essentially flushing money down the sink. Extensive modeling has been done on the NukaTap design to improve laminar flow. Integrated Seals That Are Indestructible and More Sanitary Unlike other designs, the NukaTap Mini body is made from Polyketone (POK) making it strong, robust, and able to be autoclaved. The seals are also over-molded from Santoprene® making them hard wearing so they will literally last for the lifetime of the tap without the need for replacement. Santoprene® and POK both have excellent resistance to chemicals such as caustic soda, peroxide, phosphoric acid, lactic acid, citric acid, acetic acid, and all common chemicals sold and used in the beverage industry. The seals internally are over-molded meaning no fissures or cracks exist for bacteria, crud, or yeast to hide. Superior First Pour Foam Due to Low Thermal Mass and Conductivity First pour foam is an issue caused by a warm tap body. For most faucets to pour well it's important to dispense enough beer to cool the tap body down to reach maximum performance. In addition to this the conductivity of the tab body also makes this worse so insulative materials simply work better than conductive materials. The NukaTap mini not only has very low thermal mass but is also highly insulative being made mostly from Santoprene® and POK. The combination of these two factors in conjunction with superior laminar flow makes for the lowest "first pour foam" effect out of any tap ever produced. Long Shank Alternative Most conventional beer faucets require a large 3/4" hole to be drilled through the side of your refrigerator, keezer, or cold box wall. Traditional long shanks also generally have a large volume of liquid that sits inside the wall unrefrigerated which is not ideal. New long shank alternatives developed for the NukaTap Mini are designed to suit any wall thickness and greatly reduces the stagnant beer sitting in the shank itself. For walls up to 2.7" thick, these wall mount shank kits include three screws, however if the wall is thicker, you can also use 6 small wood screws or something similar and attach three screws from the front and 3 from the back allowing you to go into any wall type. Another advantage of this new design is the tap will never accidentally rotate. Typically, other long shank beer taps rely on the hex nut on the shank to be done up tight enough to prevent rotation but if the wall compresses (often the case with foam walls) the tap is allowed to rotate. This new design has three fixing points making it impossible for the tap to rotate accidentally as the interlocking teeth behind the collet allow you to set the angle and then do up the collet to fix the tap permanently in that position.

Read more less

Silicone regulator stem o-ring. Commonly used on Taprite regulators which have an o-ring located where the regulator stem mates with the CO2 cylinder. Comes in a convenient zip lock bag. NOTE: These are not intended for use with the KOMOS CO2 Regulator. For the correct KOMOS Regulator replacement gasket, please see D1089.

Read more less

If you're tired of losing gas every time you connect or disconnect your Sodastream cylinder to your normal Sodastream cylinder adapter, this new design is what you need. Unlike cheaper Sodastream cylinder adapters, this unit has the added advantage that you can use the side thumb screw to depress the pin in the middle of the adapter. This pin adjustment makes the Sodastream cylinder adapter significantly easier to use. Some adapters require an Alan Key wrench to adjust the pin height, and depending on how worn out your seal is, you may need to adjust this pin periodically. Conventional, cheaper Sodastream adapters also tend to leak gas every time you connect and disconnect them from your regulator or the adapter itself. If you have a Sodastream Cylinder, you can use this adapter to connect it to a CGA320 CO2 Regulator. This is a great choice for mobile draft applications when you don't want to carry around your home draft system's 5 lb or larger CO2 tank. CGA320 Male Thread x TR21-4 Female Thread NOTE: Does not include CO2 regulator or Sodastream Cylinder seen in the example photos. KegLand Part Number: KL24662

Read more less

Duotight 6.35 mm OD retaining clip. Locks Duotight fittings in their closed position, making it impossible for any hose to escape. Pack of 10. KegLand Part Number: KL21937

Read more less

This is a rather simple, but extremely effective way to fill growlers from your draft system! Going to a party, but don't want to bring a keg of homebrew? Filling straight from the faucet creates a lot of foam, and you lose carbonation. Simply plug this filler into your faucet, attach some 3/8" tubing, and fill! This model is designed to fit Intertap faucets. Compatible with Intertap and NukaTap faucets. Kegland Part number: KL01045  

Read more less

This shutoff valve can be used for multiple applications. Has a 1/4 in MPT thread on one side, this is commonly used in regulators, air distributors, and other keg system components. The out side has a 1/4 in MFL fitting for attaching a variety of flare fitting such as a barb ans swivel nut for gas lines. Includes a check valve, so gas can only flow in one direction, this can protect your regulator from accidential back up of beer.

Read more less

Replacement front seat o-ring for the Perlick 630SS faucet. This is the gasket that the push back handle comes into contact with, stopping flow of the beer.

Read more less

Comes with a back nut, plastic collar, hex nut, and 8 mm Duotight Adapter compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Requires a 1" hole saw for installation. When set in place, the shank will only have about 4-1/2" of length to pass through your wall or fridge door, due to the length of the collar and back nut. Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 7-1/8" - Total Length (Tip to Tip) 6" - Shank Length (Without Nut & Barb) 5" - Thread Length 4-1/2" - Pass Through Length Kegland Part number: KL11952

Read more less

Perfect addition when purchasing a new sanke style keg coupler or tap. New taps typically come with the correct fittings for your gas line but not your beverage line. These are those fittings! Used to connect 3/16" or 1/4" beer line. To connect 3/16" beer line tubing it is helpful to heat the tubing end in hot water.

Read more less

Cooling your tower will make sure your beer stays cold from keg to glass. This fan kit blows cold air up your tower from your refrigerator which helps reduce foaming giving you a perfect pour everytime. The fan also gets rid of warm spots in your fridge by increasing air flow. Kit Includes: Fan box 12V power pack Flexible tube Kegland Part number: KL00819

Read more less

Connect two ball lock homebrewing kegs together via their ball lock our fittings. Handing for moving sanitizer or beer from one keg to the next. We often use this fitting when we have a big party where we dixie chain kegs together.  For example if you made 10 gallons of pale ale you can use this jumper to connect the two kegs so that all 10 gallons can pour at once.  

Read more less

The Intertap faucet is a forward sealing faucet similar to the Perlicks. It has a modular, threaded spout which can fit a variety of different attachments including a growler filler or a stout spout. In normal rear-sealing faucets the entire faucet has to drain of beer. In forward-sealing faucets the faucet keeps beer in it so the inside doesn't have a chance to get sticky, making cleaning much easier. It also reduces the chance of off flavors transferring to your beer while you pour. Other forward sealing faucets use a floating o-ring, which is just as sanitary but requires the o-ring to move inside the faucet body in order to seal correctly. This can become a problem as the faucet ages. Intertap faucets use a sliding shuttle that guides the o-ring into the perfect position every time.  The threaded spout easily unscrews from the faucet and can be replaced by a growler filler or stout spout quickly and easily. Pour a pint and then fill a growler in no time at all. Made of chrome plated brass.   Kegland Part number: KL00987

Read more less

With this perfect-fit replacement gasket for your draft equipment, you’ll never have to experience the frustration of trying to “rig it” again.    This molded rubber beer line gasket is used anywhere you are mounting a tailpiece. It is placed between the tailpiece and the beer taps and/or shank.

Read more less

What makes KOMOS Kegerators better than the rest? Designed to hold up to FOUR 5-gallon ball lock corny kegs (see below for full list of what fits) Serve ice cold beer even in the warmest environments thanks to highly-efficient refrigeration components Stainless steel forward-sealing faucets offer a huge upgrade over common chrome plated brass taps Choose from the classic stainless model faucet or the upgraded stainless flow control model Faucets mount to a high-quality stainless steel tower, rather than a cheap chrome plated tower Interior fan diverts cold air up into the tower to keep your beer lines cold and reduce foaming EVABarrier double walled draft tubing protects your beer against oxidation Duotight push-to-connect fittings make assembly a breeze Included KOMOS Dual Gauge CO2 Regulator maintains consistent pressure and is easily adjusted The KOMOS® Deluxe Kegerator model features an eye-catching stainless steel exterior and upgraded stainless steel drip tray The KOMOS Kegerator offers a stunning set of features that clearly separate this unit as the most modern kegerator on the market. With more interior space than other models, the KOMOS Kegerator is designed to fit up to four 5-gallon Slimline Torpedo kegs or Pepsi-style Ball Lock Corny kegs. Whether you choose the single, double, triple, or quad tap configuration, you'll receive stainless steel forward-sealing faucets in either classic or flow control model. Stainless faucets are a huge upgrade over the chrome-plated brass faucets commonly included with other kegerators, and you'll quickly recognize the quality of a forward-sealing beer faucet compared to the standard taps seen at your local tavern or in-law's mancave. Rather than a chrome plated tower, the NukaTap faucets are mounted to a stainless steel tower that remains cool before, during, and after each pour thanks to a tower fan diverter that recirculates cold air within the kegerator and blows it up into the tower to keep your beer lines cold and reduce foaming. From keg to faucet, your beer will pass through EVABarrier draft lines, a premium double-walled tubing designed to protect against beer oxidation. And with Duotight push-to-connect fittings, you'll have your lines connected in a snap with no need to force the tubing over barb fittings or fiddle with hose clamps. Other features you'll love about the KOMOS Kegerator include its highly-efficient cooling capacity so you'll be serving ice cold beer even in the warmest temperatures, extra wide temperature range from 26–82°F, dual gas inlets at the back, aluminum internal floor, rolling casters, and the included KOMOS Dual Gauge CO2 regulator. The most eye-catching difference between the KOMOS unit and other kegerators is definitely the capacity. This is the first kegerator we have offered that comes with a quadruple tap tower option, and that’s all thanks to the redesigned interior. Most kegerators position the compressor on the right or left side of the inside floor, making one side shallower than the other. KOMOS positions the compressor in the middle so both sides of the interior have an equal depth. This seemingly small detail allows the unit to hold up to four 5-gallon Slimline Torpedo or Ball Lock Corny kegs. Dual gas line inlets are absolutely clutch if you want to serve beverages at two different pressures or use two different types of gas. Both inlets are just over 3/4" in diameter and feature PCO 1881 threads. This threading allows you to use the plastic Carbonation Ball Lock Cap (FE13) as a quick connect option for your gas lines. Upgraded condenser, evaporator, and insulation make this unit highly efficient, yet quiet, so you can serve ice cold beer in even the warmest temperatures. The unique internal fan provides excellent air circulation, pulling cold air from below the evaporator and blowing it back over the top of your kegs and up into the tower to chill your draft lines. Extra Wide Temperature Range is Perfect for Homebrewers The KOMOS kegerator is tailored to a homebrewer's needs. Take, for example, the extended range digital controller with an adjustable temperature range from 26 - 82°F. This allows homebrewers to use as fermentation chamber and is something that other kegerators don't do. Although the unit does not provide heating, the extended range allows you to program the internal temperature at say an ale fermentation temp of 68°F and will provide cooling whenever the temp rises above that set point. With the insulation provided by the kegerator, heating should rarely be needed, but you can always place a low wattage heat wrap inside the unit if ever needed. The digital controller always displays the temperature and is easily adjusted from the front of the kegerator with the door closed. It's pretty nice. Forward-sealing Stainless Faucets and Towers All KOMOS kegerators come with NukaTap stainless steel forward-sealing faucets and a stainless steel draft tower. Forward-sealing means that while in the closed position the faucet will keep beer in it instead of draining out. This keeps the internal parts from getting sticky and reduces the chance of off flavors transferring to your beer while you pour. Most other kegerators on the market will only include the cheapest, standard chrome-plated beer faucets that you'd find at any dive bar. KOMOS kegerators include not only a faucet that features superior pour technology, but made from stainless steel which won't corrode over years of use. Choose from the classic forward-sealing faucet model or the upgraded flow control model that allows you to dial in the flow rate of the beverage you're dispensing. The flow control faucet is a great option for users that often switch between beer styles with different carbonation levels. No need to rebalance your lines or play with your regulator settings. Instantly make adjustments as you pour to dial in the flow rate. This is also a super convenient feature for when you want to grab a quick growler on your way out. By dialing back the flow rate, you can gently fill your growler so CO2 stays in solution and your beer doesn't pour flat when it comes time to share. Click here to learn more about the Classic and Flow Control faucet models. Duotight Fittings & EVABarrier Draft Tubing Duotight and EVABarrier have revolutionized how you connect draft line, and our kegerators come standard with both. We love Duotight push-in fittings for their quick connection, reliable seal, and versatility. Setting up and connecting draft line has never been easier -- no more hose clamps or heating water to soften tubing! Each kegerator comes with Duotight fittings for the tower shanks, regulator, and for splitting gas lines (double & triple tap only). We recommend adding Duotight fittings to use for your keg connections as well. Depending on whether you'll be serving from homebrew kegs or commercial sanke kegs, you'll need two DUO106 or two DUO104 per line. EVABarrier tubing has been engineered with protection in mind and is both PVC-free and BPA-free. This double walled tubing offers superior protection against oxidation, CO2 loss, and microbial growth. EVA tubing is the future of draft line for professional applications, and now your kegerator will feature the same first-class tubing. KOMOS Regulator The included high-quality KOMOS CO2 regulator maintains consistent pressure and features a blow-off PRV with pull ring for safety and to relieve pressure, rubber coated gauges, and a hand knob for easy adjustment. Many kegerator brands will include the cheapest regulator they can find, and while these regulators may work OK out of the box, they will eventually show signs of pressure creep which can lead to foamy beer and other issues with your draft system. Rather than have you rely on a regulator that is "just OK", KOMOS kegerators include their own premium dual gauge regulator with highly accurate precision diaphragm and heavy-duty steel gauges. Included with your kegerator package is a Duotight fitting that attaches to the regulator for an easy, solid, push-to-connect connection with your gas line. Added Features One of the unique features on a kegerator in this price range is the tower fan, which blows cold air up into your tower to reduce foaming issues. They also come standard with the KOMOS dual gauge CO2 regulator, which is super beefy and consistent in delivering accurate pressures. Most Chinese-made regulators experience creep where the pressure increases over time. The KOMOS regulator is by far the best CO2 regulator we have seen made in China. The countertop drip tray couldn't be easier to keep clean. Built-in drip trays look cool, but they're a pain to keep clean. Before long they get pretty disgusting with dried, spilled beer -- attracting fruit flies and becoming a haven for mold and bacteria to grow. They'll often overflow the reservoir inside the kegerator causing a huge mess. Our kegerator's tray is designed to be removed and easily washed. Best Value & Backed by MoreBeer! We've looked around, and when you factor in fast and free shipping, you are getting the very best value on a kegerator in the USA. Plus, you're getting MoreBeer! service if something happens in shipment. We double box the unit with foam pads and have very little shipping damage. However, it will be delivered via Fed-Ex ground so damage is possible. If your unit arrives damaged just call us up and we will work with you to take care of it. Feature Summary: Stainless Steel Air Cooled Tower NukaTap Stainless Steel Forward-Sealing Faucets Choose faucet model and number of taps above Duotight Fittings make connecting draft lines a breeze Digital Thermostat with wide 26 - 82° F temp range. Robust KOMOS Dual Gauge Regulator included CO2 Tank holder mounts on back of kegerator (tank not included) Efficient and powerful compressor Stainless steel door, top cover, and side panels Stainless Countertop Style Drip Tray Aluminum floor for additional keg support Includes EVABarrier beer and gas tubing Beverage line measures 4mm ID x 8mm OD 1 x 1.7m length of line per tap Gas line measures 5mm ID x 8mm OD 1 x line of varying length depending on number of taps (2, 2.5, or 3m) 4 Tap model includes uncut rolls of bev & gas line We recommend cutting bev lines to 1.7-2m lengths (5.5-6.5 ft.) Gas lines can be cut to whatever length best suits your needs Duotight adapters for draft shank and regulator connections Duotight tee fittings for splitting gas lines (2, 3, 4 tap only) You will need to purchase keg connections depending on whether you are serving commercial sanke, ball lock corny, or pin lock corny For ball lock and pin lock disconnects we recommend DUO106 For commercial sanke keg couplers we recommend DUO104 Available Kegerator covers and "off road" casters for moving over uneven terrain Detailed instructions on assembly and use Specifications: 23.75" wide 25" deep 31.5" with CO2 mount 32.5" Tall (fridge only) 35" with Caster wheels 48.75" with tower 51" with Casters and Tower 110 v - 60 hz 0.8 Amp draw Optimal ambient temperature is 65°F – 80°F CSA Certified Internal Dimensions: 19.5" wide 17" deep 16" down the center where compressor sits 28.5" tall What Fits: 5 Gal. Torpedo Keg - 3 5 Gal. Slimline Torpedo Keg - 4 6 Gal. Torpedo Keg - 3 5 Gal. Megamouth Torpedo Keg - 1 5 Gal. Pin Lock Cornelius Keg (Corny Keg) - 3 5 Gal. Ball Lock Cornelius Keg (Corny Keg) - 4 5.2 Gal. Oxebar PET Keg - 3 5.16 Gal. Sixth Barrel Keg (Sixtel, Log) - 3 (1) 5.16 Gal. Sixth Barrel Keg + (1) 7.75 Gal. Slim Quarter Keg 7.75 Gal. Quarter Barrel Keg (Pony Keg, Stubby Quarter) - 1 7.75 Gal. Slim Quarter Keg (Tall Quarter, The Slim) - 1 15.5 Gal. Half Barrel Keg (Full Size Keg) - 1 See below for the Kegerator Instruction Manual. (The Deluxe Kegerator does not have feature a Guard Rail as seen in the residential kegerator instructions.) Please note: This unit requires 4" of clearance on all sides and is not intended to be installed under a countertop. For a build-in unit, see the KOMOS Pro Stainless Steel Kegerator.

Read more less

Nothing looks quite as nice as beer pouring out of a shiny stainless steel draft tower. These are the same tower kits included with every KOMOS Kegerator, featuring Intertap stainless steel faucets, EVABarrier draft tubing, and Duotight push-to-connect fittings for easy assembly. The tower is made from 304 brushed stainless steel, making them corrosion resistant while also looking great! Stainless Intertap Faucets and Towers These kits come with Intertap faucets mounted on a brushed stainless tower. Intertap faucets are the newest, most advanced, forward sealing, beer faucets on the market today and will work perfectly for years. Forward-sealing means that while in the closed position the faucet will keep beer inside the body instead of draining out. This keeps the internal parts from getting sticky and reduces the chance of off flavors transferring to your beer while you pour. Intertap faucets feature a modular, threaded spout that can fit a variety of attachments including a growler filler or stout spout. Duotight Fittings & EVABarrier Draft Tubing Duotight and EVABarrier have revolutionized how you connect draft line, and our tower kits come standard with both. We love Duotight push-in fittings for their quick connection, reliable seal, and versatility. Setting up and connecting draft line has never been easier -- no more hose clamps or heating water to soften tubing! Each tower comes with Duotight fittings for the tower shanks and for splitting gas lines (double & triple tap only). We recommend adding Duotight fittings to use for your keg connections as well. Depending on whether you'll be serving from homebrew kegs or commercial sanke kegs, you'll need two DUO106 or two DUO104 per line. EVABarrier tubing has been engineered with protection in mind and is both PVC-free and BPA-free. This double walled tubing offers superior protection against oxidation, CO2 loss, and microbial growth. EVA tubing is the future of draft line for professional applications, and now your kegerator will feature the same first-class tubing. Includes: Stainless steel draft tower Intertap faucet(s) Stainless steel faucet shank(s) with Duotight tailpieces EVABarrier gas and beverage tubing Beverage line measures 4mm ID x 8mm OD Gas line measures 5mm ID x 8mm OD Draft tower mounting screws Faucet wrench 1-3 Tap Tower Dimensions: 13.4 in. tall (without faucets) 3 in. tower diameter 4.4 in. base diameter 4 Tap Tower Dimensions: 16 in. tall (without faucets) 4.5 in. tower diameter Interior mounting holes (does not include bottom collar)

Read more less

Single replacemelt ball seal (cup seal) for NukaTap draft faucets. Component #3 in the faucet diagram below. Each NukaTap has two of these washers. Also compatible with Intertap brand faucets. Not compatible with the NukaTap Mini faucet.   How to tell what generation NukaTap you have. Generation 1 - Two White Nylon Cup Seal Washers Generation 2 - Two Red Self Lubricating Nylon Cup Seal Washers Generation 3 - Two Black POK Cup Seal Washers   KegLand Part Number: KL43908

Read more less

The Stout Spout installs on the NukaTap Mini to improve the pour of your stouts and nitro brews The creamer/aerator disc inside strips out nitrogen gas for a creamier beer Simply unthread the standard spout from the NukaTap Mini and swap in the Stout Spout Simply unscrew the normal spout from the NukaTap Mini and screw this Stout Spout in its place to pour your nitro brews. This spout has a creamer/aerator disc inside that strips out the nitrogen gas for a creamier beer. Only compatible with the NukaTap Mini faucet. The Stout Spout will have a 1/4" female flare thread. KegLand Part Number: KL32858

Read more less