$1 - $50

Keep vegetal matter contained and out of your fermenter with the Hop Spider mesh filter Sits directly in your boil kettle allowing hop oils to be directly infused into your wort Kettle hanger can be bent and adjusted to dial in the height at which the filter sits inside your kettle Holds up to 12 oz of hop pellets Made from 304 stainless steel The hop spider is stainless steel mesh hop filter that hangs from the the edge of your kettle. Up to 12 oz of hops are poured directly into the spider during the boil.  Made from 304 stainless steel. The basket is 13.75 in (35cm) high with the opening at the top being 5.9 in (15cm) diameter and tapers down to a 3.9 in (10cm) diameter at the bottom. 0.4 mm aperture mesh.   Kegland Part Number: KL04688

Read more less

Purpose-built grain bag for Brew-in-a-Bag (BIAB) brewing Fits most brewing kettles up to 19" in diameter Made from polyester webbing with 1" reinforced nylon seam liners Nylon forms 4 loops at the opening of the bag that make great handholds or can be used with a winch system Perfect for Brew in a Bag, this large 27.5" x 32.5" bag will fit pots up to 19" in diameter. These polyester bags have 1-inch wide nylon sewn over the seams, making them incredibly strong and resilient. At the opening of the bag the nylon forms 4 loops, making great handholds when lifting the bag or attaching to a winch system for large BIAB batches. 63 micron mesh Temperature rated to 230°F (110°C)   Please note: when removing the bag from your kettle, always be sure to avoid thermometer probes and other accessories that may snag and tear the mesh. Be careful when using mash paddles and spoons, especially when the bag is full. Kegland Part Number: KL01304

Read more less

Forward-sealing design prevents beer residue from gumming up the faucet! Threaded spout can be replaced with a variety of attachments Unique sliding shuttle design allows the faucet to last longer than standard floating o-ring design 304 stainless steel construction The patented Stainless Steel Intertap Faucet is a forward sealing faucet that represents the most modern faucet design. It has a modular, threaded spout which can fit a variety of different attachments including a growler filler or a stout spout. In normal rear-sealing faucets the entire faucet has to drain of beer. In forward-sealing faucets the faucet keeps beer in it so the inside doesn't have a chance to get sticky, making cleaning much easier. It also reduces the chance of off flavors transfering to your beer while you pour. Other forward sealing faucets use a floating o-ring, which is just as sanitary but requires the o-ring to move inside the faucet body in order to seal correctly. This can become a problem as the faucet ages. Intertap faucets use a sliding shuttle that guides the o-ring into the perfect position every time.  The threaded spout easily unscrews from the faucet and can be replaced by a growler filler or stout spout quickly and easily. Pour a pint and then fill a growler in no time at all. 304 Stainless Steel construction so you don't have to worry about chrome plating wearing off and exposing your beer to brass.   Kegland Part number: KL00970

Read more less

Easily attaches to any Intertap faucet. Just unscrew the standard spout and replace it with this growler spout. Then you'll have a 1/2" (13mm) barb on the end of your faucet. Compatible with Intertap and NukaTap faucets. Stainless Steel Construction Kegland Part number: KL01038  

Read more less

Smooth, ribless design prevents yeast and bacteria buildup, making sanitation a breeze Punted bottom and conical top promote sediment collection and reduce oxidation during storage Extra-wide 4" mouth opening simplifies filling, additions, and cleaning Constructed from heavy-duty, virgin PET plastic without plasticizers Made with food-grade and BPA-free materials The Ported Fermonster is a brand new fermenter designed specifically for fermentation. MoreBeer! gave product feedback for over 2 years of development and we think they nailed the design. The large lid allows for easy filling and makes hop or oak additions a breeze. The smooth sides are fantastic for sanitization - no ribs or texture to collect yeast or bacteria.  The large 7 gallon size was designed to provide ample space for fermentation and you'll find the molded in volume markers super handy for accurate filling. The punted bottom allows sediment to collect to the sides so that you can siphon liquid from the center.  Because they are made from virgin PET plastic they nearly unbreakable and a lot safer than similar glass carboys. Also notice the conical top which reduces surface area if you plan to store beer or wine long term.   These ported versions come with our plastic spigot (FE347), allowing for easy racking and sampling! Made from heavy PET plastic, the same material used in 2 L soda bottles, which is nearly impermeable to oxygen penetration.  Due to the thickness of the material and the overall geometry the Fermonster does not require ribs or dimples for stability.  That results in a super smooth interior surface that reduces yeast and sediment buildup making it the easiest to clean, most sanitary PET carboy on the market.  The huge 4" opening makes filling a breeze, and cleanup is as easy as wiping down the inside.  The 7 gallon volume is a monster of a fermenter, reducing blowoff issues seen with standard 5 and 6 gallon carboys. Fermonsters are easily moved by hand or consider using our Carboy Carrier for even greater ease of use. These fermentors are completely air-tight and the lids sealed tight with an O-Ring.  Additional O-Rings and Lids both with and without holes are available for purchase, see our You Might Also Need items below. Features: 4" wide mouth carboy - easy to clean! Ported version includes Spigot for easy racking Food grade PET plastic construction is nearly impermeable to oxygen penetration No hard to clean dimples or ribs Volume Markers at 5, 6, and 7 Gallons Punted bottom O-Ring and Lid with one hole is included (Fits #10 Stopper) Additional O-Rings and Lids available Weight: 1.5 lbs Temperature Limit: 140° F Height: 20.9 inches Diameter: 11.3 inches Completely taste and odor free Perfect for Beer, Wine, Cider, Mead, Kombucha or any other fermented beverage! Thick walls for better oxygen barrier.

Read more less

Newest faucet design on the market! Reduced first pour foam due to low thermal mass Forward-sealing design prevents beer residue from gumming up the faucet Unique shuttle design greatly improves laminar flow, improving the pour of carbonated beverages Compatible with all Intertap faucet accessories and shanks First Pour Foam Reduction Every kegerator owner knows the letdown of pouring your first pint of the day and getting too much foam. Even with perfectly balanced draft lines, first pour foam is sometimes unavoidable simply due to the temperature of the faucet itself. Running beer through the faucet will drop the temperature, and the foaming will subside, but not without a bit of wasted beer from pouring off excess head. The NukaTap beer faucet drops to beer serving temperature much faster thanks to its lower thermal mass. Simply put, the bulkier the faucet is, the more beer is needed to flow through and chill the tap. The NukaTap is over 20% lighter than its Intertap predecessor, and even lighter still compared to other brands of faucets. Improved Laminar Flow The inspiration for the NukaTap name comes from its uniquely designed "nuke-shaped" shuttle that resides on the inside of the faucet. The NukaShuttle went through numerous rounds of redesigns and countless hours of testing to find a shape that provides superior laminar flow. This means that liquid passes by the shuttle with very little resistance, allowing highly carbonated beers or hard seltzers to pour like a dream. Sanitary Design The NukaShuttle is the world’s first seamless single-piece design. Traditional taps feature an o-ring seated on a stainless steel shuttle, which can cause a couple of issues. After many pours, the stainless shuttle rubbing against the internal body of the faucet will create small fissures that become potential infection sites, and the seated o-ring can be difficult to clean in place, making your draft cleaning and sanitizing process less effective than you realize. The NukaShuttle is an advanced TPV rubber matrix that has been seamlessly formed over a durable PP skeleton. This single-piece design eliminates the pitfalls of older manufacturing methods, making it one of the most sanitary faucets on the market. Forward Sealing vs. Rear Sealing From tap rooms to home bars, forward-sealing faucets are the ideal choice for any draft setup. In traditional rear-sealing taps, beer will drain out of the entire faucet when it's in the closed position. This means the internal mechanism is coated in beer, which then dries and becomes a sticky residue. Forward-sealing faucets, on the other hand, keep the tap full of beer so it never has a chance to dry and gunk up the internal parts. This makes the faucet much easier to clean and also reduces the chance of off flavors transferring to your beer while you pour. Made from stainless steel Shuttle made from TPV O-rings made from EPDM NSF approved Kegland Part Number: KL15509    

Read more less

Achieve consistent and optimal fermentation temperatures with the FermWrap Fermentation Heater. This flexible and easy-to-use unit wraps snugly around your fermenter, providing gentle and controlled heat. Use alone or simply plug into the 110V heatnig plug on most popular temp controllers Provides gentle, even heating with 40 watts spread over almost two square feet Keep your yeast happy and your ferment warm during those cold winter months with this flexible heater wrap! Don't be fooled by imitators and cheap knock-offs, this is the original FermWrap that has been produced by Fermentap for over a decade. Unlike those old heater belts, the FermWrap covers a wide area of your carboy or fermentation vessel, promoting an even heat distribution. Using tape to adhere, the FermWrap can be attached directly to your fermenter, or can be used to heat the space in a box (or refrigerator) that the fermenter is in. Depending on your configuration and insulation, you can increase the temperature of your ferment from 5-20°F. This differential can be increased by using the BrewBuilt™ Neoprene Carboy Sleeve.   With 40 watts of heat spread over almost two square feet, it provides gentle, even heating.   For more precise results, we recommend a temp controller and carboy thermowell. The controller will monitor the fermentation temp and only power on the FermWrap if the temperature drops below your set point. For the ultimate level of control, we recommend pairing it with the BrewBuilt CoolStix™ to provide cooling. With both accessories plugged into the temp controller, you'll get cooling or heating whenever you need it.   Specs: 40 watts 115V 11" H x 25" W   Item does not include carboy as pictured.   Kegland Part number: KL06255 

Read more less

The Inkbird dual stage temperature controller is an easy to use and economical controller that is perfect for home brewing. Inkbird controllers allow you to control both heating and cooling, and set independent differentials for each to keep the exact temperature you need. The Ink bird ITC-308S controller performs many of the same functions as the Ranco or Johnson but at a more affordable price, making it a great alternative for temperature control.  Aside from brewing uses, this is a great dual relay output temperature controller for cooking (use in a smoker or bbq), home growing (heat mats for seedlings, climate control), or any other DIY project you come up with! Features: Simple plug and play design with user friendly LED interface Dual stage ITC-308 - control both heating and cooling Adjustable Heating/Cooling differential 1000W max power Celsius or Fahrenheit High and low temperature and sensor fault alarms Can control temperatures of -58° F through 210° F (-50° C - 99° C) Body Dimensions: 5.5 in x 2.7 in x 1.3 in

Read more less

Quickly clean kegs and fermenters while you tend to other tasks High flow rate pump provides a powerful blast that coats the inside of the vessel Use it for cleaning or sanitizing with your favorite solutions 15L bucket provides a much larger reservoir compared to other models Everything included in the system neatly fits inside the bucket for easy storage The Bucket Blaster is a convenient and effective system for cleaning and sanitizing kegs, carboys, and other brewing vessels. The beauty of the Bucket Blaster is that you can set it and forget it. Simply set up the keg washer basin with your cleaner or sanitizer, set your vessel over the jet nozzle, power up the pump and let the Bucket Blaster do the work while you tend to other tasks. Perfect for homebrew kegs, carboys, FermZillas, or bucket fermenters. This unit comes with a 15L (3.9 gal) bucket, which doubles as a storage container when you are not using the system. Other keg washers come with a very small reservoir that make it a pain to move, as liquid spills over the sides easily and generally they just do not work as well. The Bucket Blaster's large 15L reservoir makes it much less likely for you to spill liquid on the floor, and since it can hold more cleaning solution, each cleaning cycle will be that much more effective. Includes: Submersible Pump - 2,000 L/hr 15L Bucket Powerful Jet Nozzle 9.5 mm EVABarrier Tubing Gray and Black Ball Lock Disconnects Duotight fittings for all connections Kegland Part Number: KL15905    

Read more less

An Intertap accessory that converts the spout of an Intertap faucet into a ball lock quick disconnect. One of the most popular uses is being able to connect the beverage side of your counter pressure filler without having to open your refrigerator door. Compatible with Intertap and NukaTap faucets. Stainless Steel Construction Kegland Part number: KL01052

Read more less

Oxebar Mono is a lightweight 2-gallon keg with high oxygen barrier properties compared to standard PET plastic Add the Ball Lock Adapter Tapping Head to easily pressurize and dispense at home or on the go Lighter than traditional glass growlers. Easier and safer to transport Made from Nylon impregnated PET for superior oxygen barrier Wedge seals on the optional Tapping Head and Ball Lock Caps eliminate points of oxygen ingress found where rubber is traditionally used Lower total oxygen pickup compared to a standard corny keg lid seal This 2-gallon keg is lightweight, compact and has high oxygen barrier properties with 3x better (meaning less) gas transmission than traditional PET grades of plastic making it suitable for beer storage or other oxygen sensitive carbonated and non-carbonated beverages. This product is sold with the PCO38 cap, however if you would like to dispense this product through a draft system, we recommend the use of the Ball Lock Adapter Tapping Head. The tapping head is sold separately and allows you to attach standard ball lock disconnects and pressure relief valve to the top of the keg. What is Oxebar Mono Oxebar Mono is a PET polymer blend that utilizes several polymers blended together to significantly improve gas barrier properties. When compared with standard PET plastic, Oxebar Mono is able to reduce oxygen ingress and CO2 loss so your precious beverage is preserved and shelf life extended by 3x. We recommend this product for beer storage of up to 6 months. Dimensions: Diameter: 6.1" (155 mm) Height: 20.5" (520 mm) Pressure Rating: 58 psi (4 BAR) Temperature Rating: 113°F (45°C) KegLand Part Number: KL22347   NOTE: Oxebar kegs are marked with a manufacturer’s “expiry date”. This does not indicate that the keg is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the keg be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the KG520 Tapping Head and D1072 Green PRV to perform the test. If you do not plan to pressurize the keg, the test is not necessary.

Read more less

Now a scale that you can use to measure large amounts of hops and grains at home! This is a great addition to any home brewery!   This Electronic Grain Scale is capable of weighing a full sack of grain, and then some. This benchtop unit has a 55lb capacity, lifetime warranty, and a host of helpful features.    Features: Massive 55 lb (25 kg) capacity! Optional Backlight Feature Runs on 4 x C batteries or AC adaptor (included) Large Weigh Platform 8" x 6.5" Weighs in Pounds, Pounds:Ounces, Ounces, Kilograms, Grams Dual Range Weigh Design: 0-2 lbs x 0.1oz/0-1kg x 2g 2-55 lbs x 0.5oz/1kg-25kg x 10g Display is removable and attached to two foot cord for easy viewing of the display while using larger weighing vessels

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.   For you, The Discerning Kegger, these Perlick beer faucets are a thing of beauty. When you draw off a pint, they look good, operate smoothly, and don’t gum up. They are a breeze to take apart for sanitizing. These design benefits will have you sold on the lifetime value of these taps.   #1 Design Benefit - Forward Sealing The #1 feature of the Perlick faucet is its forward sealing design. Why is that so important? In an ordinary, rear-sealing faucet, the entire faucet must drain out of beer. There is actually a pin hole in the back of an ordinary faucet that allows beer to drain out. Because beer drains from the entire faucet the faucet remains sticky and is prone to contamination from the left over residue. The Perlick faucet, with its forward sealing design, only has beer drain from the short 1" nozzle section. This allows it to always operate smoothly (even when it was not cleaned between uses) and greatly reduces contamination.   #2 Design Benefit - Stainless Steel Standard old school faucets are made of brass that is plated in chrome. The chrome plating wears off and the Brass can pit. This can result in flavor contamination when your beer runs over exposed brass and pits which usually harbor bacteria.   In the late 90's, when the first stainless faucet was released, it cost close to $100. Wow. Now you can choose to get a traditional style faucet made out of stainless, but why would you bother when you can get this unique forward sealing design and stainless construction all in the same Perlick faucet?   Sure it costs a little more but you will never regret making the upgrade now.    

Read more less

An affordable option for your first keg or adding to your growing collection These kegs are cleaned, de-labeled, sanitized, pressure tested and guaranteed to hold pressure upon delivery Used kegs may have minor cosmetic damage but are in perfect working order Rubber top and bottoms protect floors from dings These Ball Lock Corny Kegs are a sturdy, reliable keg with the MoreBeer! seal of approval. These corny kegs are cleaned, de-labeled, sanitized, pressure tested and guaranteed to hold pressure upon delivery. Every Ball Lock Cornelius Keg has a 5 gallon capacity and a rubber top and bottom. While these are used kegs with slight cosmetic damages, these light dings and scratches have no effect the keg’s performance. The relief valves, poppets and gaskets on these used kegs are not replaced before shipping, but we sell all of these items separately if you’d like to replace them yourself at home (part numbers KEG540, KEG450 & KEG500). If you’re looking for a truly economical way to serve your beer at home, this Ball Lock Cornelius Keg is a great option. Used keg with minor cosmetic damage only Ball lock corny kegs measure approximately 8.5" (diameter) x 25" (height) x 26 1/4" Height with flare fittings Soda kegs may come with either 11/16 inch body connects or 7/8" body connects Purchase deep sockets to remove body connects (part numbers KEG991 and KEG992)

Read more less

Smooth, ribless design prevents yeast and bacteria buildup, making sanitation a breeze Punted bottom and conical top promote sediment collection and reduce oxidation during storage Extra-wide 4" mouth opening simplifies filling, additions, and cleaning Constructed from heavy-duty, virgin PET plastic without plasticizers Made with food-grade and BPA-free materials The Ported Fermonster is a brand new fermenter designed specifically for fermentation. MoreBeer! gave product feedback for over 2 years of development and we think they nailed the design. The large lid allows for easy filling and makes hop or oak additions a breeze. The smooth sides are fantastic for sanitization - no ribs or texture to collect yeast or bacteria.  The 6 gallon size is great for most fermentations, and the larger 7 gallon is available for even bigger beers. The punted bottom allows sediment to collect to the sides so that you can siphon liquid from the center.  Because they are made from virgin PET plastic they nearly unbreakable and a lot safer than similar glass carboys. Also notice the conical top which reduces surface area if you plan to store beer or wine long term.   These ported versions come with our plastic spigot (FE347), allowing for easy racking and sampling! Made from heavy PET plastic, the same material used in 2 L soda bottles, which is nearly impermeable to oxygen penetration.  Due to the thickness of the material and the overall geometry the Fermonster does not require ribs or dimples for stability.  That results in a super smooth interior surface that reduces yeast and sediment buildup making it the easiest to clean, most sanitary PET carboy on the market.  The huge 4" opening makes filling a breeze, and cleanup is as easy as wiping down the inside.  Fermonsters are easily moved by hand or consider using our Carboy Carrier for even greater ease of use. These fermentors are completely air-tight and the lids sealed tight with an O-Ring.  Additional O-Rings and Lids both with and without holes are available for purchase, see our You Might Also Need items below. Features: 4" wide mouth carboy - easy to clean! Ported version inlcudes spigot for easy racking Food grade PET plastic construction is nearly impermeable to oxygen penetration No hard to clean dimples or ribs Volume Markers at 5 and 6 Gallons Punted bottom for less sediment transfer during racking O-Ring and Lid with one hole is included (Fits #10 Stopper) Additional O-Rings and Lids available Weight: 1.5 lbs Temperature Limit: 140° F Height: 19.25 inches Diameter: 11.25 inches Completely taste and odor free Perfect for Beer, Wine, Cider, Mead, Kombucha or any other fermented beverage! Thick walls for better oxygen barrier.

Read more less

The Pluto Beverage Gun is the ultimate hand held beer tap!  If you have been dispensing your draft beer out of a standard picnic tap, it's time to upgrade.  Definitely one of the coolest draft beer taps that we've seen, this Pluto Beverage Gun is made from nylon and stainless steel.  The body is plastic, while the barb, piston, and spring are all stainless.  Comes with a 1/4" duotight-compatible barb perfect for use with EVABarrier draft line. You will need either the 8mm x 6.5mm or 9.5mm x 6.5mm Duotight reducer to connect the EVABarrier to the Pluto. Kegland Part number: KL00956

Read more less

Filter your tap water and eliminate that no-win decision of "should I buy expensive bottled water or use the chlorinated water from the tap." This water filter kit features a 10" carbon block filter that removes all chlorine and organic flavor. Kit includes 10" housing, one carbon block filter, garden hose attachment, barbed fittings and 6' of 3/8" vinyl tubing. The carbon block should be replaced after filtering approximately 800 gallons of water or after 1 year of use, whichever comes first. Filter should be disassembled and stored dry when not in use. NOTE: This product should not be used in hot water applications. Cold water only! This product includes a carbon filter and is designed to filter water only (Carbon filters should not be used to filter beer or wine).

Read more less

Smooth, ribless design prevents yeast and bacteria buildup, making sanitation a breeze Punted bottom and conical top promote sediment collection and reduce oxidation during storage Extra-wide 4" mouth opening simplifies filling, additions, and cleaning Constructed from heavy-duty, virgin PET plastic without plasticizers Made with food-grade and BPA-free materials The Fermonster is a brand new fermenter designed specifically for fermentation. MoreBeer! gave product feedback for over 2 years of development and we think they nailed the design. The large lid allows for easy filling and makes hop or oak additions a breeze. The smooth sides are fantastic for sanitization - no ribs or texture to collect yeast or bacteria.  The large 7 gallon size was designed to provide ample space for fermentation and you'll find the molded in volume markers super handy for accurate filling. The punted bottom allows sediment to collect to the sides so that you can siphon liquid from the center.  Because they are made from virgin PET plastic they nearly unbreakable and a lot safer than similar glass carboys. Also notice the conical top which reduces surface area if you plan to store beer or wine long term.   Made from heavy PET plastic, the same material used in 2 L soda bottles, which is nearly impermeable to oxygen penetration.  Due to the thickness of the material and the overall geometry the Fermonster does not require ribs or dimples for stability.  That results in a super smooth interior surface that reduces yeast and sediment buildup making it the easiest to clean, most sanitary PET carboy on the market.  The huge 4" opening makes filling a breeze, and cleanup is as easy as wiping down the inside.  The 7 gallon volume is a monster of a fermenter, reducing blowoff issues seen with standard 5 and 6 gallon carboys. Fermonsters are easily moved by hand or consider using our Carboy Carrier for even greater ease of use. These fermentors are completely air-tight and the lids sealed tight with an O-Ring.  Additional O-Rings and Lids both with and without holes are available for purchase, see our You Might Also Need items below. Features: 4" inner diameter wide mouth carboy - easy to clean! Food grade PET plastic construction is nearly impermeable to oxygen penetration No hard to clean dimples or ribs Volume Markers at 5, 6, and 7 Gallons Punted bottom O-Ring and Lid with one hole is included (Fits #10 Stopper) Additional O-Rings and Lids available Weight: 1.5 lbs Temperature Limit: 140° F Height: 20.9 inches Diameter: 11.3 inches Completely taste and odor free Perfect for Beer, Wine, Cider, Mead, Kombucha or any other fermented beverage! Thick walls for better oxygen barrier.

Read more less

This magnetic drive pump is a perfect pump for your brew system. Use it to move hot wort in an all-grain system and also to transfer wort from boil kettle to fermenter. The housing of the unit is made from tough, food grade food-grade heat-resistant SPS. The magnetic drive allows you to slow down the flow without damaging the pump. This pump is not self priming so do not run the pump dry. The pump head can be rotated in 60-degree increments, allowing for 6 different pump head orientations. Optional stainless steel pump head upgrades available—standard stainless center inlet head or stainless inline tri-clamp head. Want More! power? Check out this pump's bigger brother, the 60-Watt MKII. Features: 110v/60hz Max Head: 11.15 ft. (3.4 m) Max Flow: 5 Gal/min (19L/min)  1/2" BSP fittings Rotatable pump head Max temperature - 248 F/ 120 C Water resistant (not proof!) casing Kegland Part Number: KL05470

Read more less

Heavy-duty ball lock quick disconnect made from 304 stainless steel for lifetime longevity Etched "In" label to clearly identify the QD for beverage use Pairs perfectly with stainless steel Torpedo Kegs and compatible with all ball lock corny kegs 1/4" flare thread connection Your Kegs are made out of stainless steel, why settle for plastic Quick Disconnects?  Upgrade your serving setup to fully Stainless with a pair of Torpedo Ball Lock QDs!  These hefty pieces are constructed of 304 SS, designed for lifetime longevity.  Printed clearly with "In" and "Out" so even after a few they're easy to work with.  Available for both Beer Out and Gas In, with either Barbed or Flared connections.  See YMAN's below for the appropriate connectors! A flare fitting washer (KEG602) is recommended for use with this product. Perfect with our Torpedo Kegs, these will work with any Ball Lock Corny Keg. Features: 304 SS Construction - Built to last a lifetime 1/4" Flare connection Clearly Labeled Ball Lock Gas In 2" Height

Read more less

If you have spent uncounted hours washing and sanitizing bottles on bottling day, then you know what a drag that can be. Save time and simplify your life by making this tool a regular part of your bottling process. Simply add some sanitizing solution the the clear dish section of the injector, then place a bottle upside down one the white nozzle and pump it a few times to spray sanitizer inside the bottle. The nozzle provides the correct spray pressure and coverage to fully coat the inside of the bottle in just a few pumps. Able to be installed on top of our Ferrari brand rotating bottle trees (B510 or B517), or used separately on the countertop. It only takes a few minutes to sanitize 2 cases of bottles, letting you get on with bottling and then the rest of your day! Please Note: Does not fit other brand bottle trees or on the Ferrari fixed based tree with handle (B518).

Read more less

Automatically release pressure inside your fermenter during pressure fermentations Regulate beer flow during pressurized transfers from fermenter to keg Built-in pressure gauge for easy reference when adjusting the spunding valve Pressure gauge is interchangeable—swap to different pressure ranges that better suit your application Diaphragm spunding valves offer higher accuracy compared to spring & poppet spunding valves Comes complete with Duotight ball lock QD and rigid joiner With this complete kit you'll be ready to use the BlowTie 2 Spunding Valve right out of the box. The BlowTie is used to release excess pressure on a pressurized fermenter or from a receiving keg during pressure transfers. This diaphragm spunding valve is much more accurate than the spring and poppet style, and works much better at lower pressures. This version of the Spunding Valve Kit includes the Duotight Ball Lock QD which allows you to attach the BlowTie directly to the QD via the 8 mm rigid joiner. The BlowTie 2 can also be upgraded with a Digital Mini Pressure Gauge. Pressure Fermentation Pressure fermentation is becoming more and more popular at the homebrew level, but in order to do it safely and accurately, you need a way to release excess pressure. You'll pressurize your vessel to your desired psi, but once fermentation begins and those hungry, active yeast start creating CO2, the pressure inside the vessel will increase. Attach a spunding valve and set it to your desired pressure, and it will blow off when the pressure gets to high and close up again when it's back to your desired psi. Pressure Transfers Even if you don't have a pressurizable fermenter, you may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process. Diaphragm vs. Poppet With the poppet style spunding valve, a spring pushes against a poppet to keep the valve closed. When the poppet lifts up to open, the surface area the gas pushes against becomes larger, and the spring has to work harder to push the poppet down and reseal the valve. This can lead to more gas being released than intended, and the remaining pressure in your vessel may be at a lower psi than your spunding valve’s set psi.  Instead of a poppet, the spring inside the BlowTie pushes against a diaphragm, which has an immensely larger surface area. This means the surface area that the gas pushes against while the diaphragm is closed is significantly closer to the surface area it pushes against when the diaphragm is open. This leads to higher accuracy, and the remaining pressure after excess gas is released will be much closer to your set blow off pressure. Kit Includes: BlowTie 2 w/ Integrated Pressure Gauge (0-15 psi) 8 mm Duotight Gray Ball Lock Disconnect 8 mm OD Rigid Plastic Joiner  

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in late December. For an in stock 5 lb CO2 tank option, please see our D1050.   Serve beer on tap at home! A quality CO2 tank is a core component to any home draft system. Made from high-quality aluminum that will never rust like steel tanks Dispense up to 9 x five-gallon kegs of homebrew CGA320 valve pairs with standard US-style CO2 gas regulators KOMOS® offers a full suite of first-rate draft products and draft fittings—from kegs to faucets and everything in between! Standard 5 lb size is ideal for home draft applications—compact enough to fit inside you kegerator and won't need to be refilled too often Brand new aluminum 5 lb CO2 tank made from high strength aluminum alloy and high quality CGA320 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It’s called a 5 lb tank because it holds 5 lbs of compressed (liquified) CO2. 5 lbs of CO2 is enough to dispense about 8 to 9x 5-gallon kegs of homebrew. Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder. Tanks should always be stored in an upright position. Features: Made from corrosion resistant, engineered Aluminum Brushed finish Thick, durable cylinder walls 18" T x 5.25 Ø DOT approved New high quality CGA-320 valve Light weight compared to steel tanks

Read more less

The Deluxe Yeast Starter Kit will have you making top shelf yeast starters right out of the box. Yeast starters offer higher cell counts at the time the yeast is pitched, leading to faster, healthier fermentations and better tasting beer! Any beer will benefit from a yeast starter, but they're especially recommended for high gravity beers and cold fermenting lagers. This kit includes step-by-step instructions for making a 2L starter, as well as some fantastic upgrades that set it apart from our standard Y320 starter kit. Once you've prepared the starter, sanitize and drop in the stir bar, install the foam stopper, and place the flask on the magnetic stir plate. Turn the dial up until a shallow vortex forms. Magnetic Stir Plate A stir plate will greatly improve the quality of your yeast starter by providing continuous aeration. Yeast need oxygen to produce sterols and multiply. When all the available oxygen is used up the yeast will stop reproducing. Using a stir plate will ensure that your yeast have all the oxygen they could ever want and they'll be able to reproduce as much as possible. Foam Stopper Many yeast starter kits include a rubber stopper and airlock, but we believe a foam stopper is the clear choice. The foam stopper will allow air to flow freely into your flask while keeping pesky bugs and other contaminants out. Simply spray or dunk the stopper in sanitizer before installing it. If you're going to store the starter for a couple days after its finished, remove the foam stopper and cover the flask with sanitized aluminum foil. Foam Axe Foam Axe from CellarScience® is a uniquely formulated anti-foaming agent which reduces surface tension so bubbles are Axed before they can form.  Foam Axe can be used in the kettle to help prevent boil-overs and works great in your fermenter or starter flask to reduce Krausen—stopping your viable yeast from fermenting out the top of your vessel. Just one drop in your flask is all you need. Flask Marker This wax pencil is used for writing on glass surfaces and washes off easily. Great for labeling and writing notes on your yeast starter. Kit Includes: 2000 mL Erlenmeyer flask (student grade) Magnetic Stir Plate (stir bar included) Foam Stopper 1/2 lb Dried Malt Extract 1 oz Fermaid K yeast nutrient 1 oz Foam Axe foam control Flask Marker wax pencil In the lab world, these flasks are known as "Student Grade". A great flask for making yeast starters! (Student grade is not the highest grade flasks and will have minor defects)

Read more less

Modeled after the most popular Mexican-style lager in the U.S., Corona Extra. Light, crisp, and refreshing Includes 100% Galena hops Estimated ABV: 4.7% Estimated IBUs: 15 Makes 5 gallons of finished beer Sometimes you just want a reliable, simple beer that you know will quench your thirst. Our Reina del Sol Lager is modeled after the most popular Mexican-style lager in the U.S., Corona Extra. Whether you're relaxing under the sun on a pool day or getting beat down by merciless rays on a chore day, you can always count on this crisp, refreshing Mexican Cerveza to cool you off. In that fashion, we designed a straightforward recipe that consists of Pilsner malt, flaked corn and a scoop of Carapils with two dashes of Galena hops to provide just a kiss of bitterness. To make it a true to form cerveza, ferment cold with a Mexican yeast strain like CellarScience® BAJA. Originally developed and popularized by the Modelo Group, this Mexican yeast strain produces clean lagers and finishes dry. Makes 5 gallons Estimated Original Gravity: 1.044-49 SRM (Color Range): 3 IBUs: 15 Estimated Alcohol Percentage: 4.7% Our recipe kits DO NOT include grain bags, yeast or priming sugar. To find our yeast recommendations, choose your preferred kit option above and then select the drop-down menu under “Yeast Options”.  For more info, click on the recommended yeast(s) below in the “You Might Also Need” section below. All grains will come milled, unless you select unmilled base malts.  

Read more less

The beer filter gets installed inline between two ball lock Cornelius kegs using CO2 pressure to push the beer out of the full keg through the filter and into the clean keg. This kit is designed to filter out particles down to 1 micron, which is considered fine filtration. At one micron the beer will be clear after filtration provided you do not have a starch haze. Filtering also accelerates the conditioning process to just a few days. Most of our customers who use the filtering kit find that they; keg beer, chill it overnight, filter the next day, carbonate, and are drinking clear beer in a couple days. For those who want to bottle beer without sediment, filtering combined with the use of a counter pressure bottle filler will allow you to put crystal clear, carbonated beer into bottle. The beer filtering kit comes with one 10" filter housing, a 1 micron 10" spun poly sediment filter, fittings for connection to the filter housing, 3' of beverage line, clamps, and two beverage out ball lock quick disconnects. Spun-polypropylene filters are disposable filters and cannot be cleaned and used more than once. However, you can filter multiple kegs with one filter. 3 micron will remove most yeast, and 1 micron filtration will remove almost all yeast. All filters are rated nominal (will filter out 80-85% of matter at given rating). Temperature rated to 125°F.

Read more less

96% reduction in oxygen ingress compared to silicone O-rings when measured in a keg! Made from a special blend of materials, these gaskets offer vastly improved oxygen barrier properties compared to Silicone or EPDM Give your beverage the absolute best protection from oxygen staling with KegLand's Low2 O-rings! The result is your beverage staying fresher for longer! Compatible with any ball lock or pin lock corny-style keg with standard lid Upgrade the storage life of your beer by replacing your standard keg lid O-ring with the new Low2 O-ring from KegLand. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Compatible with any ball lock or pin lock corny-style keg with a standard size lid. Not compatible with Megamouth Torpedo Kegs. Low2 O-rings were independently tested by GunnLab, an Australia-based plastic packaging testing laboratory. See below for a printout of the test results. KegLand Part Number: KL03063

Read more less

Add this neoprene jacket to your Gen 4 BrewZilla to speed up heating! Heating is 10% faster and heat loss from the boiler is reduced by 50% Remove the jacket after the boil to speed up chilling Thick, insulating neoprene is secured to the boiler body with a sewn-on hook and loop fastener strap Sparge arm sleeve included to reduce heat loss during mash recirculation Add some insulation to your BrewZilla to get better boils! This neoprene jacket will help keep the heat in for quicker and more vigorous boils. Slap it on to speed up heating; take it off to speed up chilling. Also includes a neoprene sleeve for the recirculation arm to reduce heat loss during the mash. This jacket will fit Gen 4 BrewZilla models. It is not compatible with older generations of BrewZillas and DigiBoils due to where the cutouts on the jacket are located. Features: 10% faster heat up time 50% less heat loss from boiler Fits the 35L BrewZilla Gen 4 Made from 8 mm thick neoprene which is easy to wash after use KegLand Part Number: KL24365  

Read more less

The counter pressure bottle filler that sets the standard for filling beer bottles at home.  With a unique one way valve and adjustable pressure relief you will be bottling sediment free homebrew with ease.   If you currently carbonate and store your homebrew in kegs, you can use a counter pressure filler to bottle beer directly from your kegs. One huge advantage of this method is that since you are bottling already carbonated, clear beer, there will be no sediment at the bottom of your bottles. Counter pressure bottle filling is how a brewery bottles beer. The bottle is under pressure while the carbonated beer flows in. Because the interior of the bottle is pressurized there is minimal loss of the CO2 in solution. The opposite of filling under pressure is when you pour a beer into a pint glass where CO2 erupts out of solution creating all that foam. Great in your glass but not good when you are trying to bottle carbonated beer. Our counter pressure filler mimics a single filling head on a professional bottling line, a concept that we all know works very, very well. Made by Fermentap, the design has two unique features. Number 1 it is the only model made entirely from stainless steel. Number 2 you flush and fill from the bottom of the bottle. Beer barb is 3/16". Gas barb is 5/16". Features While some models flush the bottle from the top and fill from the bottom, our unit features a special valve that allows CO2 and beer to flow down the same stainless tube, directly to the bottom of the bottle. First CO2 flows down into the bottom of the bottle to flush from the bottom up. Next you switch the valve position and beer flows down the same tube, filling from the bottom up. The result is a more effective purging of oxygen and no foam during the filling process - not to mention that the whole thing takes one-hand to operate! Why hope that you flushed your bottle properly using a type of beer gun, when you can know for sure that you have created the best environment for your beer to be stored at by using a Counter Pressure Bottle Filler? More Details The unit is inserted into the bottle in the off position. The valve is then turned to CO2 to flush the bottle and then to beer for filling. The adjustable pressure relief on the side of the unit allows you control the speed of fill by adjusting the pressure in the bottle. The valve is positioned in such a way that it is easy to use with one hand, while the other holds the bottle. This model is designed for 12oz bottles but can easily be extended to accommodate larger bottles, such as 22oz, with a small piece of 1/4" tubing. Setting Your PSI Pressure Before you counter pressure fill a bottle make sure you are satisfied with the carbonation level and flavor. The goal for counter pressure bottle filling is to store your beer in the most sanitary and clean environment possible so when you get ready to share your homebrew its presentation is perfect when you go to pour. An ideal set point to set your PSI level on your regulator is 10-14 psi. This range is dependent upon the temperature of your beer and the carbonation level. We recommend you start at a lower pressure around 10psi for the first 2-3 bottles to make sure you get everything dialed in before committing to filling a whole case. Make sure your keg is always kept cold. If your keg warms up you will have foaming issues.     

Read more less

Yeast starters offer higher cell counts at the time the yeast is pitched, leading to faster, healthier fermentations and better tasting beer!   You may be wondering how to make a yeast starter.  Well, lucky for you this kit contains everything you need for making your own yeast starter right out of the box, including step-by-step instructions!   This is the most common size used to make yeast starters using liquid yeast, great for higher alcohol beer and cold fermented lagers.   In the lab world, these flasks are known as "Student Grade," meaning there may be some cosmetic flaws in the glass, and the volume measurements are approximate due to variations in the thickness of the glass walls of the flask. This makes it a great flask for making yeast starters--at a great price!   We do not recommend the use of an electric element with these flasks. If this cannot be avoided, we suggest using a larger pot as a hot water bath on the stove.

Read more less

Unique Core Puncturing / Actuator results in zero gas lost from screwing in CO2 cartridges Interchangeable ball lock disconnect orientations. 45° for plastic QDs or 90° for stainless QDs 6.5mm Duotight compatible hose barb Swappable mini pressure gauge remains well protected within solid cast brass regulator body Corny-style 65psi Green PRV for added safety and manual depressurizing Switch from 16g to 74g CO2 cartridges with an adapter fitting The new Core 360 Mini CO2 Regulator from KegLand represents a huge jump forward in the mini regulator market. After much feedback on how to make mini regulators more compact, sturdy and efficient, the brilliant engineers at KegLand have come up with this mini-beast. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. Heavy Duty Construction Starting with the body of the regulator, this unit is made from chrome-plated solid cast brass which means it will stand up to quite a bit of abuse. Unlike most mini regulators, the pressure gauge on the Core 360 is safely recessed in the regulator body, so if you ever drop it there is little chance that you'll damage the gauge. What's more, the gauge is removable, so you can swap it out with another mini gauge with a pressure range that better suits your application. Unique Cartridge Connection What really sets this unit apart from other mini regulators is the way in which you insert a CO2 cartridge. A common complaint with these types of regulators is that you can lose a lot of gas from the cartridge just from threading it into the regulator. There's that brief period where the cartridge has been punctured but you haven't fully threaded it into the regulator to form a seal. If you're not quick enough, this can result in a significant amount of lost gas. The Core 360 has a unique design feature where inserting the cartridge is a 2-step process. First you fully thread in the cartridge so it forms a seal before it's opened, and then you screw down the actuator pin to release gas into the regulator. Simple and effective. Furthermore, the Core 360 Mini Regulator is designed to be compatible with both 16g and 74g cartridges. Out of the box it will be ready to accept 16-gram 3/8"-24 UNF threaded cartridges. But with a simple adapter you can switch to 74-gram 5/8"-18 UNF threaded cartridges. Interchangeable Gas Outlet Another feature we haven't seen before on a mini regulator is the interchangeable gas outlet. You can use the swivel nut connection to directly attach the regulator to a flare ball lock disconnect, or you can swap to the 6.5mm Duotight-compatible barb and connect draft tubing. This is a great option if you want to dispense a commercial keg without the need of a ball lock to sanke coupler adapter. The regulator also has two outlet options at either a 45° or 90° angle which makes this the ideal mini regulator regardless of whether you use plastic or stainless steel ball lock disconnects. SodaStream Compatible If you remove the 16g cartridge bushing, you'll find TR21-4 female threads for use with SodaStream gas cylinders. These can be a great option for mobile dispensing as they provide much more gas than a CO2 cartridge and are more easily transported than a full CO2 tank. Includes: KegLand Core 360 Mini Regulator 6.5mm Duotight-compatible hose barb Female Flare Fitting for MFL Disconnects Port end cap 65psi Green PRV SodaStream to 16g thread bushing KegLand Part Number: KL20404 Warning: Do not overtighten onto your cylinder. It is recommended that you use a spanner to hold the neck of your SodaStream cylinder while attaching and detaching the Mini 360 Core Actuator Regulator.  

Read more less

Track your beverages stats right on the keg or fermenter. These reusable tags will adhere to any smooth surface and have a white board finish so you can write on them with dry erase markers. Great for keeping notes and following the development of your brew from grain to glass.  

Read more less

Our most affordable brewing kit! Includes the most necessary items you'll need to make your first beer A great starter kit choice if you already have a 2.5-3 gallon pot at home Measuring & testing equipment included to track fermentation temperature and alcohol production Includes cleaning equipment and sanitizer so you'll be ready for your first brew and the next! Step-by-Step instruction pamphlet fine-tuned over 20 years for easy success Our Homebrewing Starter Kit gets you started in homebrewing at a very affordable price. It is also the simplest system to use. Anyone can follow the step-by-step directions and produce truly great beer  with the first batch! This upgradeable system is designed around two, food-grade plastic buckets which feature our handy Sediment Block Spigots for quick and easy liquid transfers. After performing the Brew Day boil process, the first bucket is used to ferment the beer for two weeks. It's then transfered into the second bucket at bottling time, and out of that bucket into your bottles.   This Kit Includes: Food Grade Plastic Six Gallon Ferrmenter with spigot, stopper and airlock Food Grade Bottling Bucket with spigot Mesh bags for steeping grain and hops on Brew Day Thermometer for easy termperature managment Hydrometer for making key sugar measurements Transfer Tubing Bottling Wand with shut off valve Sturdy Bottle Capper 50 Bottle Caps Bottle Cleaning Brush Star San Sanitizer for true sanitizing You Will Also Need: A Brewing Kettle A Beer Ingredient Kit for each batch you brew (48) 12 oz or (24) 22 oz cappable Beer Bottles or a Home Kegging System to package your beer    

Read more less

Mark’s Mark II Keg Washer™ is designed to clean and sanitize large vessels like cornelius kegs and carboys. This keg cleaner is also intended to provide a sanitation container for miscellaneous items such as airlocks, thermometers, tubing, keg fittings, and more. Quiet, Fun, & Easy to Use Very quiet when in use and most importantly speeds up the process of cleaning and sanitizing.    Light in weight.  Easy to store.  Cleans Kegs This keg washer cleans and sanitizes a cornelius keg without having to take apart the ball lock fittings, poppets, and dip tubes. You can clean the keg and the dip tube simultaneously using the T adapter. Cleans Tubing Too Cleans tube separately utilizing the pump with the additional barb fittings included.  Cleans Parts Reservoir holds 1.25 gallons of water making it easy to fill and empty with sanitizer.     Saves water and sanitizer.  The keg washer does not have an on/off switch, you can plug it directly into a wall outlet to operate the pump or plug it into an outlet that is controlled by a switch. Never leave the keg washer unattended when in use. When in use, fill the keg washer up to about 1 inch under the brim. The pump is not self priming, so always make sure the basin is full of water before plugging in the pump. Owner's Manual is included. Please read thoroughly before using. Dimensions of the inside of the washer's reservoir are: 6"L x 12"W x 4"D. Please Note: Product does not include the bucket, carboy, or keg pictured above for display purposes. The pump specs are: 520 GPH 120 Volts AC 40 watts Ceramic shaft, impeller  

Read more less