Convert 3/4" BSPP (Straight Thread) fittings to 1.5" Tri-Clover. Often used on 20x20 plate filters, where the stock 3/4" barbed inlet and outlet fittings are replaced with these to convert to 1.5" Tri-Clover. Use along with our H928 o-ring to form a seal on the straight threads.
Please note: This stopper was designed for use with the BrewBuilt CoolStix which has been discontinued. Two of the holes are for an airlock and thermowell, but the third 1/2" hole was intended for the CoolStix and you will need to plug it or utilize it how you see fit.
This #10 3-hole silicone stopper is used alongside the BrewBuilt CoolStix for Carboys. The holes are for a 1/2" CoolStix, an airlock, and a thermowell.
The holes measure 0.500", 0.413", & 0.375"
Compatible with Fermonsters and our Plastic PET Carboys listed below under "You Might Also Need".
Extension tube with 2" tri-clamp fittings on both ends. 10" in length. Made from 304 stainless steel.
Can be used with the copper reflux or pot still by attaching the H707 weldless bulkhead to the BrewZilla / DigiBoil distillation lid.
Kegland Part Number: KL10665
Use this 4" T.C. end cap to attach an airlock to your kegmenter unit. The hole measures 13/16", which is perfect for a #3 stopper (FE410VS). Kegland Part Number: KL06163
#6.5 stopper - solid. Top diameter 1.34 inches (34 mm), bottom diameter 1.06 inches (27 mm), length 1 inch (25 mm).
BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet.
Max. Temperature Rating: 158 °F (70 °C).
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product.
Thick wall tubing is recomended for pumping and pressurized systems. For siphoning and transferring liquids, see our thin wall and transfer tubing.
#9.5 stopper - with 3/8 inch hole. Top diameter 1.8 inches (46 mm), bottom diameter 1.5 inches (38 mm), length 1 inch (25 mm).
BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet.
To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole.
Max. Temperature Rating: 158 °F (70 °C).
Quality Tri-Clover fitting made from food safe stainless steel.
This is a 1.5" Tri-Clamp fitting with a 1" Barb. Use with 1" ID tubing. Made of quality 304-type stainless steel. 1.5" long stem.
Used to clean the inside of tubing using a pump. Place in the line, hook up to the outlet of the pump and push through the line. Be careful not to suck into the pump head! Available in sizes for 1/2", 1", 1.5" and 2.5" inner diameter tubing.
Stainless steel 3 way ball valve with 1/2" female BSP at all ends. The T Port configuration has multiple open and closed positions. Please refer to see the function of each handle position.
KegLand Part Number: KL15882
Replacement gasket for the ForgeFit® 1.5" butterfly valve. We recommend replacing your butterfly gasket at least every 3 years. If you wait until you have a leak, your valve has already been unsanitary for some time.
Female Garden Hose Thread on one side with 1/2" MPT on the other. Useful for customizing your chilling configuration!
A gasket is included inside the female garden hose thread portion.
Hose clamp suitable for 3/4" to 1-1/4" OD tubing
Go-to clamp for anywhere you need to secure tubing
Easily adjusted with a flathead screwdriver
Made from stainless steel
These Stainless Steel hose clamps are perfect to keep around as your go-to clamp. Use them anywhere you want to be sure your tubing will stay connected. They are perfect for silicone hoses and hooking up quick disconnects, pumps, or on any system that may need a tight seal. These stainless clamps tighten up better than cheaper ones, and the stainless steel won’t corrode. It’s handy to keep a few spares around, just in case.
Stainless steel hose clamp will fit hoses with 3/4" through 1-1/4" OD.
#12 natural latex rubber stopper with 3/8 inch hole. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Top diameter 64 mm, bottom diameter 54 mm, length 27 mm
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product.
Thick wall tubing is recomended for pumping and pressurized systems. For siphoning and transferring liquids, see our thin wall and transfer tubing.
The construction of braided silicone enables the tubing to handle increased pressure applications. Reinforced silicone offers outstanding resistance to temperature extremes and is made from FDA-sanctioned ingredients. The flexible design and construction of this tubing allows excellent bend radii and permits installation in restricted spaces without impeding flow.
3/8" inner diameter, 5/8" outer diameter
Open mesh polyester braiding incorporated within the wall of silicone tubing
Made from FDA-sanctioned ingredients
Translucent natural color for visual contact with the flow
Able to resist extreme temperature variation: -40°F to 392°F (-40°C to 200°C)
Odorless, tasteless, and inert
Working Pressure: 94 psi
Burst Pressure: 275 psi
Platinum cured
Conforms to FDA CFR 177.2600, NSF
Use this end cap to close off unwanted or uneeded tri-clamp ports.
For 3" tri-clamp fittings
Made from 304 stainless steel
ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.
If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 4 mm (5/32") ID size is perfect for homebrew draft applications where only a short beer line is needed. We recommend using 5-6 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 4 mm (5/32") Outer Diameter - 8 mm (5/16") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. Kegland Part number: KL06224
Stainless - 1.5" TC Ferrule. Used to weld in a TC connection anywhere you need one! Total Length: 1 3/32" Inner Diameter: 1 13/32". AiSI304 Stainless Steel.
Effortless Bung Removal: The ridge design ensures easy and hassle-free removal of the bung, simplifying barrel management. Effective Airlock System: Acts as an airlock, allowing CO2 to escape while keeping oxygen out, making it perfect for fermentation processes. Versatile Fit: Compatible with 30- and 60-gallon barrels, Variable Volume tanks, and 2" tri-clamp ferrules, offering flexibility across various setups. Multi-Size Replacement: Replaces stopper sizes #10, #11, and #12, with precise measurements for a perfect fit and easy assembly. We recently discovered this premium breathable silicone barrel bung and were immediately impressed with its robust design and features. To start with, the ridge really helps make bung removal effortless. The bung acts as an airlock and allows the release of CO2 while maintaining a seal against oxygen coming in. This makes the bung ideal for alcoholic or malolactic fermentation in barrels or tanks. Fits 30- and 60-gallon barrels as well as the hole in the lid of most Variable Volume tanks! Also fits perfectly in a 2" tri-clamp ferrule Replaces Stopper Sizes #10 , #11, #12 Stopper Measurements: 1.65" x 2.19" (42 mm x 55.5 mm) The flapper stopper protrudes roughly 2.5" from the stopper to allow for easy assembly Other available sizes include the Breathable Carboy Bung and the Universal Breathable Bung. All three size options can be purchased in one complete bundle with the Breather Bung Pack.
#5.5 stopper - with 3/8 inch hole. Top diameter 1.11 inches (28 mm), bottom diameter 0.95 inches (24 mm), length 1 inch (25mm).
BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet.
To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole.
Max. Temperature Rating: 158 °F (70 °C).
Stainless steel Tri-Clamp reducer with 4" T.C. and 2" T.C. connections. This reducer can be used to attach the Copper Pot Still Top (DS120) or Copper Reflux Still Top (DS130) to Kegmenters with 4" T.C. ferrules (FE581& FE582). Kegland Part Number: KL06156
Convert 1.5" Tri-Clamp to 1.5" Barb for connection of 1.5" ID tubing. 304-type stainless steel. 4.5" long stem. This long barb is the perfect TC fitting for banded brewery hoses.
Use this reinforced vinyl tubing any place in your brewing system where you want an added layer of protection from tubing failure.
This 1" ID Reinforced Vinyl Tubing is food-grade approved up to 158F. It is often used in a in a brewing system where higher pressures will be used or for commercial applications. Because it is reinforced, it is less flexible than standard vinyl tubing. Tubing has a max working pressure of 250 PSI.
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product.
Thick wall tubing is recomended for pumping and pressurized systems. For siphoning and transferring liquids, see our thin wall and transfer tubing.
Reinforced silicone tubing offers higher temperature tolerances and chemical resistance while remaining flexible and easy to handle. Ideal for both cold side and hot side processes and high-pressure applications. Although braided, the tubing remains transparent to allow you to visually inspect the flow of liquids.
1/2" inner diameter
3/4" outer diameter
Odorless, tasteless and inert
Polyester heat resistant fiber reinforcing braid
Good electrical and weatherability properties
Resists UV, Ozone, gases, and moisture
Working Temperature: -76°F–500°F
Working Pressure: 0-150 psi
KegLand Part Number: KL25300
#7.5 stopper - with 3/8 inch hole. Top diameter 1.5 inches (39 mm), bottom diameter 1.22 inches (31 mm), length 1 inch (25 mm).
BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet.
To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole.
Max. Temperature Rating: 158 °F (70 °C).
When you want to customize your own setup, it’s good to have the right fitting on hand.
This stainless steel compression fitting gives you the versatility to put your setup together in the way that works best for you.
304-Type Stainless Steel compression fitting.
1/2" Comp. x 1/2" MPT
304-type polished stainless.
A set of "elbows" is great for connecting hoses to a pump so they run parallel to each other. With 2" and 3" hose, this dramatically reduces the space needed to allow the pump to pass. In addition, having the lines run parallel makes the pump more agile when moving around the winery when connected.
