Kegging Homebrew

Automatically release pressure inside your fermenter during pressure fermentations Regulate beer flow during pressurized transfers from fermenter to keg Large triple scale pressure gauge with extended 0-40 PSI pressure range Diaphragm spunding valves offer higher accuracy compared to spring & poppet spunding valves Comes complete with ball lock QD, Duotight adapter, tee, and rigid joiners With this complete kit you'll be ready to use the Blow Tie Spunding Valve right out of the box. The BlowTie is used to release excess pressure on a pressurized fermenter or from a receiving keg during pressure transfers. This diaphragm spunding valve is much more accurate than the spring and poppet style, and works much better at lower pressures. Pressure Fermentation Pressure fermentation is becoming more and more popular at the homebrew level, but in order to do it safely and accurately, you need a way to release excess pressure. You'll pressurize your vessel to your desired psi, but once fermentation begins and those hungry, active yeast start creating CO2, the pressure inside the vessel will increase. Attach a spunding valve and set it to your desired pressure, and it will blow off when the pressure gets to high and close up again when it's back to your desired psi. Pressure Transfers Even if you don't have a pressurizable fermenter, you may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process. Diaphragm vs. Poppet With the poppet style spunding valve, a spring pushes against a poppet to keep the valve closed. When the poppet lifts up to open, the surface area the gas pushes against becomes larger, and the spring has to work harder to push the poppet down and reseal the valve. This can lead to more gas being released than intended, and the remaining pressure in your vessel may be at a lower psi than your spunding valve’s set psi.  Instead of a poppet, the spring inside the BlowTie pushes against a diaphragm, which has an immensely larger surface area. This means the surface area that the gas pushes against while the diaphragm is closed is significantly closer to the surface area it pushes against when the diaphragm is open. This leads to higher accuracy, and the remaining pressure after excess gas is released will be much closer to your set blow off pressure. Kit Includes: BlowTie Pressure Gauge (0-40 psi) Ball Lock Disconnect Duotight Tee & Flared Duotight Fitting 2x Lengths of EVABarrier 8mm OD Tubing  

Read more less

Automatically release pressure inside your fermenter during pressure fermentations Regulate beer flow during pressurized transfers from fermenter to keg Built-in pressure gauge for easy reference when adjusting the spunding valve Pressure gauge is interchangeable—swap to different pressure ranges that better suit your application Diaphragm spunding valves offer higher accuracy compared to spring & poppet spunding valves Comes complete with ball lock QD, Duotight adapter, and rigid joiner With this complete kit you'll be ready to use the BlowTie 2 Spunding Valve right out of the box. The BlowTie is used to release excess pressure on a pressurized fermenter or from a receiving keg during pressure transfers. This diaphragm spunding valve is much more accurate than the spring and poppet style, and works much better at lower pressures. This version of the Spunding Valve Kit includes the CM Becker Ball Lock QD, often considered the finest quality in plastic ball lock quick disconnects, and an 8 mm Duotight Flare Adapter for connecting to the BlowTie. The BlowTie 2 can also be upgraded with a Digital Mini Pressure Gauge. Pressure Fermentation Pressure fermentation is becoming more and more popular at the homebrew level, but in order to do it safely and accurately, you need a way to release excess pressure. You'll pressurize your vessel to your desired psi, but once fermentation begins and those hungry, active yeast start creating CO2, the pressure inside the vessel will increase. Attach a spunding valve and set it to your desired pressure, and it will blow off when the pressure gets to high and close up again when it's back to your desired psi. Pressure Transfers Even if you don't have a pressurizable fermenter, you may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process. Diaphragm vs. Poppet With the poppet style spunding valve, a spring pushes against a poppet to keep the valve closed. When the poppet lifts up to open, the surface area the gas pushes against becomes larger, and the spring has to work harder to push the poppet down and reseal the valve. This can lead to more gas being released than intended, and the remaining pressure in your vessel may be at a lower psi than your spunding valve’s set psi.  Instead of a poppet, the spring inside the BlowTie pushes against a diaphragm, which has an immensely larger surface area. This means the surface area that the gas pushes against while the diaphragm is closed is significantly closer to the surface area it pushes against when the diaphragm is open. This leads to higher accuracy, and the remaining pressure after excess gas is released will be much closer to your set blow off pressure. Kit Includes: BlowTie 2 w/ Integrated Pressure Gauge (0-15 psi) CM Becker Gray Ball Lock Disconnect Duotight Flare Fitting 8 mm OD Rigid Plastic Joiner  

Read more less

Automatically release pressure inside your fermenter during pressure fermentations Regulate beer flow during pressurized transfers from fermenter to keg Built-in pressure gauge for easy reference when adjusting the spunding valve Pressure gauge is interchangeable—swap to different pressure ranges that better suit your application Diaphragm spunding valves offer higher accuracy compared to spring & poppet spunding valves 8 mm Duotight inlet/outlet for use with 8 mm OD EVABarrier tubing or 8 mm Rigid Joiners The Blow Tie Spunding Valve is used to release excess pressure on a pressurized fermenter or from a receiving keg during pressure transfers. This diaphragm spunding valve is much more accurate than the spring and poppet style, and works much better at lower pressures. The BlowTie 2 features an integrated pressure gauge so you can quickly and easily dial in your pressure setting. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. Pressure Fermentation Pressure fermentation is becoming more and more popular at the homebrew level, but in order to do it safely and accurately you need a way to release excess pressure. You'll pressurize your vessel to your desired psi, but once fermentation begins and those hungry, active yeast start creating CO2, the pressure inside the vessel will increase. Attach a spunding valve and set it to your desired pressure, and it will blow off when the pressure gets too high and close up again when it's back to your desired psi. Pressure Transfers Even if you don't have a pressurizable fermenter, you may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process. Diaphragm vs. Poppet With the poppet style spunding valve, a spring pushes against a poppet to keep the valve closed. When the poppet lifts up to open, the surface area the gas pushes against becomes larger, and the spring has to work harder to push the poppet down and reseal the valve. This can lead to more gas being released than intended, and the remaining pressure in your vessel may be at a lower psi than your spunding valve’s set psi. Instead of a poppet, the spring inside the BlowTie pushes against a diaphragm, which has an immensely larger surface area. This means the surface area that the gas pushes against while the diaphragm is closed is significantly closer to the surface area it pushes against when the diaphragm is open. This leads to higher accuracy, and the remaining pressure after excess gas is released will be much closer to your set blow off pressure. Set Up The BlowTie spunding valve comes with 8 mm Duotight fittings on the inlet and outlet, and we recommend using it with EVABarrier 8 mm OD tubing (D1717 or D1718). You'll also need the flare Duotight fitting (DUO106) in order to attach it to a ball lock or pin lock disconnect. Dialing in your desired pressure is even easier with the BlowTie 2, thanks to the integrated pressure gauge. Simply start with the adjustment knob fully closed, then slowly open it until the gauge reading matches your desired pressure setting. Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends Interchangeable pressure gauge Gauge reads from 0-15 psi WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Kegland Part number: KL15042  

Read more less

Automatically release pressure inside your fermenter during pressure fermentations Regulate beer flow during pressurized transfers from fermenter to keg Built-in pressure gauge for easy reference when adjusting the spunding valve Pressure gauge is interchangeable—swap to different pressure ranges that better suit your application Diaphragm spunding valves offer higher accuracy compared to spring & poppet spunding valves Comes complete with Duotight ball lock QD and rigid joiner With this complete kit you'll be ready to use the BlowTie 2 Spunding Valve right out of the box. The BlowTie is used to release excess pressure on a pressurized fermenter or from a receiving keg during pressure transfers. This diaphragm spunding valve is much more accurate than the spring and poppet style, and works much better at lower pressures. This version of the Spunding Valve Kit includes the Duotight Ball Lock QD which allows you to attach the BlowTie directly to the QD via the 8 mm rigid joiner. The BlowTie 2 can also be upgraded with a Digital Mini Pressure Gauge. Pressure Fermentation Pressure fermentation is becoming more and more popular at the homebrew level, but in order to do it safely and accurately, you need a way to release excess pressure. You'll pressurize your vessel to your desired psi, but once fermentation begins and those hungry, active yeast start creating CO2, the pressure inside the vessel will increase. Attach a spunding valve and set it to your desired pressure, and it will blow off when the pressure gets to high and close up again when it's back to your desired psi. Pressure Transfers Even if you don't have a pressurizable fermenter, you may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process. Diaphragm vs. Poppet With the poppet style spunding valve, a spring pushes against a poppet to keep the valve closed. When the poppet lifts up to open, the surface area the gas pushes against becomes larger, and the spring has to work harder to push the poppet down and reseal the valve. This can lead to more gas being released than intended, and the remaining pressure in your vessel may be at a lower psi than your spunding valve’s set psi.  Instead of a poppet, the spring inside the BlowTie pushes against a diaphragm, which has an immensely larger surface area. This means the surface area that the gas pushes against while the diaphragm is closed is significantly closer to the surface area it pushes against when the diaphragm is open. This leads to higher accuracy, and the remaining pressure after excess gas is released will be much closer to your set blow off pressure. Kit Includes: BlowTie 2 w/ Integrated Pressure Gauge (0-15 psi) 8 mm Duotight Gray Ball Lock Disconnect 8 mm OD Rigid Plastic Joiner  

Read more less

The Push-In Pressure Gauge is the ideal companion for the BlowTie spunding valve (FE960). It comes with an 8 mm (5/16 in.) barb, specifically designed to be compatible with 8 mm Duotight fittings. By pairing this pressure gauge with the BlowTie, you'll be able to easily set your blow off pressure when using the BlowTie for pressure fermentations or pressure transfers. The dial face is triple-scaled to read in psi, bar, and kPa. 8 mm (5/16") push-in barb Rubber coated to protect gauge 0-40 psi / 0-2.5 bar / 0-250 kPa Kegland Part number: KL07696

Read more less

Automatically release pressure inside your fermenter during pressure fermentations Regulate beer flow during pressurized transfers from fermenter to keg Diaphragm spunding valves offer higher accuracy compared to spring & poppet spunding valves 8 mm Duotight inlet/outlet for use with 8 mm OD EVABarrier tubing or 8 mm Rigid Joiners The Blow Tie Spunding Valve is used to release excess pressure on a pressurized fermenter or from a receiving keg during pressure transfers. This diaphragm spunding valve is much more accurate than the spring and poppet style, and works much better at lower pressures.   Pressure Fermentation Pressure fermentation is becoming more and more popular at the homebrew level, but in order to do it safely and accurately you need a way to release excess pressure. You'll pressurize your vessel to your desired psi, but once fermentation begins and those hungry, active yeast start creating CO2, the pressure inside the vessel will increase. Attach a spunding valve and set it to your desired pressure, and it will blow off when the pressure gets too high and close up again when it's back to your desired psi.   Pressure Transfers Even if you don't have a pressurizable fermenter, you may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process.   Diaphragm vs. Poppet With the poppet style spunding valve, a spring pushes against a poppet to keep the valve closed. When the poppet lifts up to open, the surface area the gas pushes against becomes larger, and the spring has to work harder to push the poppet down and reseal the valve. This can lead to more gas being released than intended, and the remaining pressure in your vessel may be at a lower psi than your spunding valve’s set psi.    Instead of a poppet, the spring inside the BlowTie pushes against a diaphragm, which has an immensely larger surface area. This means the surface area that the gas pushes against while the diaphragm is closed is significantly closer to the surface area it pushes against when the diaphragm is open. This leads to higher accuracy, and the remaining pressure after excess gas is released will be much closer to your set blow off pressure.   Set Up The BlowTie spunding valve comes with 8 mm Duotight fittings on the inlet and outlet, and we recommend using it with EVABarrier 8 mm OD tubing (D1717 or D1718). You'll also need the flare Duotight fitting (DUO106) in order to attach it to a ball lock or pin lock disconnect. Dialing in your desired pressure is very simple. Although you would ideally use the BlowTie with the Push-In Pressure Gauge (D1160) and Duotight Tee Fitting (DUO109), as seen in the example photo, you can easily set the blow off pressure without it. To do this, simply pressurize an empty keg to your desired psi using your CO2 regulator. Before attaching the BlowTie to the gas post, be sure to turn the dial clockwise until it is fully closed. Once attached, slowly turn the dial counterclockwise until gas starts coming out, then slightly turn the dial back to stop the gas flow. The BlowTie is now set to your desired pressure.   Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends 0-40 psi pressure rating   Please note: the BlowTie does not come with the pictured accessories. Please see "You Might Also Need" below for the other products shown in the example photo.  Kegland Part number: KL03643

Read more less

This Ball Lock QD With Pressure Gauge and Adjustable PRV is a great accessory to have when performing pressure transfers. Made from stainless steel components for long-lasting quality. Features the Torpedo Keg gas-in disconnect and adjustable stainless gas pressure relief valve (D1833L). This model also features a pressure gauge that reads from 0-15 psi. Don't need the gauge? Check out the FIL42S. Pressure Transfers You may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having an adjustable pressure relief valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process. Note: The very end of the pressure relief valve can be adjusted by unscrewing the knurled adjustment knob. If too tight and not adjustable by hand, wrap a towel around the adjustment knob and loosen with pliers. Then finger tighten or loosen to desired pressure.  

Read more less

A great accessory to have when performing pressure transfers. Designed by the MoreBeer! R&D team and made from stainless steel components for long-lasting quality. Features the Torpedo Keg gas-in disconnect and our specially designed adjustable stainless gas pressure relief valve (D1833L). Looking for a PRV valve with pressure gauge? Check out the FIL42AS. Pressure Transfers Great for pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process.   Note: The very end of the pressure relief valve can be adjusted by unscrewing the knurled adjustment knob. If too tight and not adjustable by hand, wrap a towel around the adjustment knob and loosen with pliers. Then finger tighten or loosen to desired pressure.  

Read more less

The Slimline Torpedo Keg series features a smaller diameter to maximize the space in your kegerator or keezer Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Torpedo Kegs too wide? Want to squeeze another keg in your kegerator? The patented design, D794,899, of the Slimline Torpedo Keg is 9% more slim than the classic model with all the same great features. Coming in at about 1/4" thinner than standard Ball Lock Cornelius Kegs, this keg has welded stainless handles and the ability to stack kegs with fittings still in place all at a great price. Quality First Here at MoreBeer! we love nothing more than quality interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. Torpedo kegs are machine welded and exceed our standards for quality. This weld quality is possible because these kegs are made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. “In” and “Out” is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Taking your keg on the go? Don't leave home without a custom tailored Slimline Torpedo Keg Sleeve! Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions:   Height (in.) Diameter (in.) 1.5 Gal 11 8 3/8 2.5 Gal 15 5/8 8 3/8 5 Gal 25 1/2 8 3/8   For a slightly shorter keg, see our Standard Torpedo Kegs!  

Read more less

Brand new, all-stainless construction ball lock keg Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Set your sights on a brand new Torpedo Keg! The patented, D794,899, sleek all-stainless design represents the pinnacle of quality in ball lock homebrew kegs. With features like welded stainless handles, the ability to stack with fittings in place, amazing quality and a great price we think these kegs will become the standard by which other kegs are measured.    Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Taking your keg on the go? Don't leave home without a custom fitted Torpedo Keg Sleeve! Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions:   Height (in.) Diameter (in.) 1.5 Gal 10.25 9 2.5 Gal 14.75 9 5 Gal 23 9 Please Note: These are about 1/2" wider than standard Ball Lock Cornelius Kegs. Need something a bit slimmer?  Check out our lineup of Slimline Torpedo Kegs!  

Read more less

Forward-sealing design prevents beer residue from gumming up the faucet! Threaded spout can be replaced with a variety of attachments Unique sliding shuttle design allows the faucet to last longer than standard floating o-ring design 304 stainless steel construction The patented Stainless Steel Intertap Faucet is a forward sealing faucet that represents the most modern faucet design. It has a modular, threaded spout which can fit a variety of different attachments including a growler filler or a stout spout. In normal rear-sealing faucets the entire faucet has to drain of beer. In forward-sealing faucets the faucet keeps beer in it so the inside doesn't have a chance to get sticky, making cleaning much easier. It also reduces the chance of off flavors transfering to your beer while you pour. Other forward sealing faucets use a floating o-ring, which is just as sanitary but requires the o-ring to move inside the faucet body in order to seal correctly. This can become a problem as the faucet ages. Intertap faucets use a sliding shuttle that guides the o-ring into the perfect position every time.  The threaded spout easily unscrews from the faucet and can be replaced by a growler filler or stout spout quickly and easily. Pour a pint and then fill a growler in no time at all. 304 Stainless Steel construction so you don't have to worry about chrome plating wearing off and exposing your beer to brass.   Kegland Part number: KL00970

Read more less

Simply unscrew the normal spout on an Intertap faucet and screw this stout spout in its place to pour your nitro brews. This spout has a creamer/aerator disc inside that strips out the nitrogen gas for a creamier beer. For additional disc options, check out the 7-Disc Creamer/Aerator Kit. Compatible with Intertap and NukaTap faucets. Stainless Steel Construction Kegland Part number: KL01021

Read more less

High performance primary regulator designed to handle the workload of dispensing from multiple taps without freezing up! Dual high-pressure and low-pressure gauges to easily reference CO2 cylinder pressure and output pressure Pressure settings are easily adjusted by hand using the large plastic adjustment knob CGA320 inlet features a built-in gasket where the unit attaches to the CO2 tank—eliminating the need of replacing fiber washers with each tank swap Made in the USA. Taprite is one of leading manufacturers of gas regulators and draft dispensing equipment One-way shutoff valve outlet protects your regulator from backflow and can be turned on/off to stop gas flow without needing to close your tank When it comes to CO2 regulators, we’ve tried them all. This quality unit by Taprite is our favorite on the market. It’s no wonder this regulator is trusted by so many breweries and beer bars—it represents the best quality at a great price. Available in a standard, single-body model, as well as a dual-body model which allows you to send different pressures to two separate kegs from the same CO2 tank! The things you’ll love about this regulator are:  The large front knob makes pressure adjustment tool-free, easy & fast.  The built-in gasket where the regulator connects to the CO2 tank eliminates the constant replacement of fiber washers every time you change out your tank.  The barbed outlet features a one-way on/off valve which prevents backflow and protects the regulator’s internals.  The gauges are easy to read. The low pressure gauge reads from 0 to 60 psi. The optional available gauge cage is the best on the market. This is the T742HP model, where the HP stands for high performance; it won't freeze up when multiple taps are running at once. Best of all is the consistent pressure regulation. With many regulators the pressure can 'creep' up over time. This unit holds the pressure rock steady. No drifting.    Built by Taprite, an American company. 

Read more less

Replacement gaskets and o-rings for the Intertap SS and PC faucets Does not work with Intertap FC faucets or NukaTap faucets. Kegland Part number: KL01168

Read more less

The X1 Faucet has been used for many beverage dispense applications over the years including beer, soda, carbonated water and other beverages. This faucet is a great choice when you need to dispense very cold beer that might freeze a metal faucet. This configuration features a self-closing faucet lever, and a lever flow control adjustment system. Please note: the faucet handle and draft shank in the example photo are not included. Self-Closing, Lever Adjustment Food Grade (NSF Approved) plastic and stainless steel Full length European Flow Control (completely control restriction at the faucet;no restriction line needed) Made in Germany and assembled in the USA! Features a built in "Creamer" function so you can put a fine cream head on your beer Used in restaurants and bars locally and abroad  

Read more less

An amazing Curved Forward Sealing Creamer Faucet from CMBecker! This heavy duty, yet sophisticated, faucet looks great with its unique stainless steel bent tube spout. Made in Germany and assembled in the United States. Engineered to be full of technological advantages to help you pour the perfect beer using the most sanitary system in the industry. Please note: the faucet handle and draft shank in the example photo are not included. Forward seal for better sanitation and operation 304 Stainless Steel construction for longer life and no “leaching” of materials Features a built in “Creamer” function so you can put a fine cream head on your beer Closed Piston chamber with encapsulated compression sprin

Read more less

It is time to move forward with the technologically advanced, forward seal faucet from CMB, the V3S.  This faucet is very compact, beautifully finished and full of technological advantages to help you pour the perfect beer. The sleek European design complements the look of your beer system. Please note: the faucet handle in the example photo is not included. Forward Seal for better sanitation and operation. Made in Germany and assembled in the USA! Features a built in “Creamer” function so you can put a fine cream head on your beer Creamer also works well for coffee beverages where a creamy texture is desired. 304 Stainless Steel construction will not affect the flavor of beer, wine and other beverage Works well for Beer, Wine and other acidic beverages. Vents at the top for better sanitation Closed Piston chamber with encapsulated compression spring, This gives you Consistent pressure between forward seal o-ring and seating area Eliminates dripping and leaking issues found in some forward seal designs Extends the life of the sealing O-ring for years of service between replacements No beer is trapped in system or exposed to air, which provides more sanitary conditions.

Read more less

The V10 stainless steel flow control faucet is designed and produced in Germany with some assembly completed in the United States. This faucet contains technology such as the "Closed Piston Chamber with Encapsulated Compression Spring" that allows for a perfect forward seal on the faucet, no beer trapped in dead space to cause the lever to stick, and the ability to push the faucet backwards for an extra creamy head. The compensator itself has an extra long cone for a wider range of compensation and designed to eliminate uncontrolled shifting of the compensator cone. This configuration features a black standard faucet knob, a polished stainless steel faucet lever, and a lever flow control adjustment system. Please note: The CM Becker X1 and V10 flow control faucets require a proprietary draft shank and will not work with a standard draft shank. Please select on of the draft shanks below to add to your order. 2.5" Chrome Exterior w/ Food Grade Liner (D12907) 2.5" Stainless Steel (D12908) 5-3/8" Stainless Steel (D12909) Features: Full length European Flow Control (completely control restriction at the faucet;no restriction line needed) Made in Germany and assembled in the USA! Features a built in “Creamer” function so you can put a fine cream head on your beer Used in restaurants and bars locally and abroad The faucet handle and draft shank in the example photo are not included.  

Read more less

The most high-quality KOMOS regulator, featuring an integrated nut-hand-wheel that allows for effortless, one-handed tightening to your CO2 cylinder Internal components are accessible from the backplate for easy cleaning and servicing Includes a Duotight adapter for EVABarrier tubing and a 1/4" flare fitting with barb, allowing for quick and adaptable gas line setups The PRV is rated to 65 psi and can be swapped out with 17-psi, 35-psi, or 100-psi rated PRVs if desired Rubber gauge protectors safeguard gauges from potential damage Compatible with standard US CO2 tanks The robust body and precision diaphragm provide high flow rates, and the pressure can be easily and precisely adjusted with the hand dial. Extra thick stainless gauges come with rubber bumpers for added protection. The dial faces are triple-scaled to read in psi, bar and kPa. The PRV is rated to 65 psi (4.5 bar) for added safety while in use. Comes with male flare thread gas-out with included 1/4" barb and nut. Easily swap out the barb to a different size if desired. On the back of the regulator body are three M6 screw holes for mounting (screws not included). Each KOMOS regulator includes a Duotight Adapter, allowing for quick connection of EVABarrier draft tubing for a solid, yet easy to change, way of connecting gas line. Add Duotight Tees to easily split the line to multiple kegs. Features: One-handed Cylinder Tightening: Attach the regulator to your CO2 cylinder effortlessly with one hand using the integrated nut-hand-wheel. No separate spanner or wrench is needed! This is made possible by a new spigot seal design that compresses easily without the risk of damage or leaks. Simplified Self-Servicing: Maintain your regulator with ease by accessing the internal components from the backplate. Simply use an 8mm hex/Allen key to remove the regulator knob and access the internals for cleaning, eliminating the need for a vise or specialized tools. Flared Output: The regulator features an output with 1/4" male flare connection. Each regulator comes with a 1/4" barb and nut as well as an 8mm Duotight adapter for use with your preferred tubing. Triple-Scale Gauge: Monitor your CO2 pressure accurately with the Class 2.5 gauge, featuring PSI, bar, and kPa scales for easy reading (+/- 2.5% accuracy). Durable Seat Cap Assembly: The new seat cap is constructed from ultra-high molecular weight polyethylene, providing exceptional resistance to wear and tear. This robust design minimizes the risk of scratching and brass filings, which can lead to pressure creep, even under demanding conditions like forced carbonation. Reinforced Steel Gauges: Benefit from enhanced durability with thicker steel gauges built to withstand rigorous use. Color-Coded PRV: This regulator includes a 65 PSI green PRV (pressure relief valve).  This can be swapped to the Red (35 PSI) or Gray (100 PSI) PRV if desired. Easy Mounting: Integrated M6 mounting holes allow for secure and convenient installation. Note that the nut-wheel needs to be removed for flush mounting. Specs: 0–60 PSI operating range Low pressure gauge reads from 0–100 Pull ring PRV rated to blow off at 65 PSI 1/4" & 5/16" barb fittings included Duotight adapter for EVABarrier tubing included Standard US CO2 Threads (CGA320) Gauge protectors M6 mounting screw holes Made in accordance with AS 4267

Read more less

Serve beer on tap at home! A quality CO2 tank is a core component to any home draft system. Made from high-quality aluminum that will never rust like steel tanks Dispense up to 9 x five-gallon kegs of homebrew CGA320 valve pairs with standard US-style CO2 gas regulators KOMOS® offers a full suite of first-rate draft products and draft fittings—from kegs to faucets and everything in between! Standard 5 lb size is ideal for home draft applications—compact enough to fit inside you kegerator and won't need to be refilled too often Brand new aluminum 5 lb CO2 tank made from high strength aluminum alloy and high quality CGA320 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It’s called a 5 lb tank because it holds 5 lbs of compressed (liquified) CO2. 5 lbs of CO2 is enough to dispense about 8 to 9x 5-gallon kegs of homebrew. Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder. Tanks should always be stored in an upright position. Features: Made from corrosion resistant, engineered Aluminum Brushed finish Thick, durable cylinder walls 18" T x 5.25 Ø DOT approved New high quality CGA-320 valve Light weight compared to steel tanks

Read more less

The Megamouth Torpedo Keg series features an extra-large lid opening for easy cleaning Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams The Megamouth Torpedo Kegs are by far the easiest to clean and maintain out of any ball lock homebrew keg you'll find. With an extra-large lid opening, even the buffest of homebrewer (we hear they do exist!) will have no trouble reaching in for a good scrub when it kicks—no expensive keg washing contraptions needed! The Megamouth makes for an excellent pressurizable fermentation vessel and is the ideal choice for brewers who prefer to add dry hops and other flavoring ingredients directly to the keg. Quality First Here at MoreBeer! we love nothing more than quality interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. Torpedo kegs are machine welded and exceed our standards for quality. This weld quality is possible because these kegs are made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. “In” and “Out” is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Overall for the price and quality, along with free shipping from MoreBeer!, the Torpedo Keg is an amazing value! Specifications: Mouth Opening: 5.8" L x 4.8" W. Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions:   Height (in.) Diameter (in.) 3 Gal 13.4 11.4 5 Gal 17.9 11.4 6 Gal 20.5 11.4 10 Gal 30.3 11.4  

Read more less

New Corny Keg ready to use right out of the box New Kegs are trouble-free for years Rubber top and bottoms protect floors from dings Lid includes a tab wth hole welded in so you can hang anything from lid (dry hop our favorite) 304 Stainless Steel and great welds, this will last a tifetime Features Low2 Keg Lid O-ring which offers a 96% reduction in oxygen ingress compared to silicone Ditch the bottles and start kegging today! Save time, reduce the risk of infection and get all those bottles out of the kitchen for good! Brand new 5 gallon Kegland kegs offer convenience, security and insurance when compared to used or reconditioned kegs. There's no need to replace gaskets or other parts, no need to trust that someone else did a good job with reconditioning, and no possibility of residual flavor or aromas getting into your beer! Features: Ball lock 130 PSI Operating Pressure 5 Gallon (19 L) Capacity Dry Hop Tab Welded into Lid 304 Stainless Steel Dimensions: Height: 24.75 in. Diameter: 8.375 in. Kegland Part Number: KL02899

Read more less

This handy adapter fits on standard keg couplers with its Female Beer Thread (5/8" BSP) and allows a ball lock connection on the gas side of the coupler. Made from 304 stainless steel. Kegland Part number: KL00833

Read more less

With this perfect-fit replacement gasket for your draft equipment, you’ll never have to experience the frustration of trying to “rig it” again.    This molded rubber beer line gasket is used anywhere you are mounting a tailpiece. It is placed between the tailpiece and the beer taps and/or shank.

Read more less

It is time to move forward with the technologically advanced, forward seal faucet from CMB, the V3S.  This faucet is very compact, beautifully finished and full of technological advantages to help you pour the perfect beer. The sleek European design complements the look of your beer system. Please note: the faucet handle in the example photo is not included. Forward Seal for better sanitation and operation. Made in Germany and assembled in the USA! Features a built in “Creamer” function so you can put a fine cream head on your beer Creamer also works well for coffee beverages where a creamy texture is desired. 304 Stainless Steel construction will not affect the flavor of beer, wine and other beverage Works well for Beer, Wine and other acidic beverages. Vents at the top for better sanitation Closed Piston chamber with encapsulated compression spring, This gives you Consistent pressure between forward seal o-ring and seating area Eliminates dripping and leaking issues found in some forward seal designs Extends the life of the sealing O-ring for years of service between replacements No beer is trapped in system or exposed to air, which provides more sanitary conditions.  

Read more less

Brand new ball lock keg—no need to clean out an old, used Coke or Pepsi soda keg! Dual rubber handles make it easy to grip, lift, and move the keg when full Rubber base is less likely to damage flooring in your home or kegerator Made from 304 stainless steel in and commerical-quality FSSC 22000 Certified facility This brand-new, corny-style ball lock keg features a molded rubber base and dual-handle top for easy handling and stacking. The comfortable grip handles make it easier to maneuver when full, while the rubber base protects both your floor and the keg itself. This durable keg is constructed from high-quality 304 stainless steel and manufactured in an IFSSC 22000-certified facility. Features: Ball lock 130 PSI Operating Pressure 2.5 Gallon (9.5 L) Capacity 304 Stainless Steel Produced in an FSSC 22000 Certified Facility Dimensions: Height: 14.75 in. Diameter: 8.75 in.

Read more less

Handles both dispensing and rapid burst carbonation, ideal for seltzers and high-carbonation drinks requiring 30-40 psi Includes both Duotight and barb fittings for use with EVABarrier tubing or standard gas tubing Features a shutoff valve for safe operation and standard US CO2 tank threads (CGA320) Rubber gauge protectors safeguard gauges from potential damage Compatible with standard US CO2 tanks The KOMOS Dual Gauge Precision Universal Regulator is suitable for both dispensing and carbonating beverages. Compared to the Precision Dispensing model, the Universal model features a wider 0-50 psi operating range, enabling pressures above 25 psi for rapid burst carbonation. This is particularly useful for seltzer and other highly carbonated drinks requiring 30-40 psi dispensing pressure. The regulator includes both Duotight and barb fittings for compatibility with EVABarrier draft tubing and standard gas tubing. The gas outlet features a shutoff valve for safe and convenient operation. Rubber gauge protectors are also included to safeguard the gauges from potential damage. Features: 0-50 PSI operating range Low pressure gauge reads from 0-60 psi Pull ring PRV rated to blow off at 50 psi Narrow pressure range for increased precision 1/4" & 5/16" barb fittings included Duotight adapter for EVABarrier tubing included Standard US CO2 Threads (CGA320) Shutoff valve Gauge protectors Ideal for dispensing or carbonating beverages

Read more less

This handy adapter fits on standard keg couplers with its Female Beer Thread (5/8" BSP) and allows a ball lock connection on the beer side of the coupler. Made from 304 stainless steel. Kegland Part number: KL00840

Read more less

The X1 Faucet has been used for many beverage dispense applications over the years including beer, soda, carbonated water and other beverages. This faucet is a great choice when you need to dispense very cold beer that might freeze a metal faucet. This configuration features a self-closing faucet lever, and an Allen Key Security flow control adjustment system. Please note: the faucet handle and draft shank in the example photo are not included. Self-Closing, Allen Key Security Adjustment Food Grade (NSF Approved) plastic and stainless steel Full length European Flow Control (completely control restriction at the faucet;no restriction line needed) Made in Germany and assembled in the USA! Features a built in "Creamer" function so you can put a fine cream head on your beer Used in restaurants and bars locally and abroad  

Read more less

This is a rather simple, but extremely effective way to fill growlers from your draft system! Going to a party, but don't want to bring a keg of homebrew? Filling straight from the faucet creates a lot of foam, and you lose carbonation. Simply plug this filler into your faucet, attach some 3/8" tubing, and fill! This model is designed to fit Intertap faucets. Compatible with Intertap and NukaTap faucets. Kegland Part number: KL01045  

Read more less

D-Type keg coupler for standard American sanke kegs Stainless steel keg probe Click-to-engage ergo lever handle Includes 1/4" OD barbs for gas inlet and liquid outlet The most popular keg coupler in the USA. Commercial D-Style sanke beer tap, also called a coupler, has a lock down mechanism that gives a solid click when engaged. Heavy duty construction is designed to withstand commercial usage. Beer is dispensed out of the top port, the side port is for gas. Nickel coated body with stainless steel probe This is the default tap used by most American Craft breweries. Here is a partial list of breweries that have been reported to being using American D style kegs.  Abita ACME Alaskan Alexander Keith Anderson Valley Bad Frog BayHawk BBC Black Dog Blanche de Chambly Blue Moon Breckenridge Brooklyn Bruin Pale Ale Budweiser Busch Carlsburg Celis Cider Jack Columbia Brewing Coors Coors Light Corona Deschutes Black Butte Devil Mountain Dos Equis Eel River Brewing Ellicottville E.J. Phair Fat Tire Firehouse Firestone Flying Dog Foster's Full Sail Genesee George Killian's Irish Red Goose Island Gordon Biersch Grant's Green Mountain Cidery Hamms Hard Core Cider Henry Weinhard's High Falls Holy Cow Red Hornsby's Hudson Valley Humboldt Ice House Killarney Killian's Irish Red Kirin Ichiban Kokanee Labatt Blue Leinenkugel Little Kings Lost Coast Lowenbrau (US) Mad River Maudite Miami Trail Brewing Michael Shea's Michelob Mickey's Middle Ages Miller Milwaukee's Best Modelo Molson Canadian Moosehead Natural New Amsterdam New Zeland Steinlager Nor'Wester North Coast O'Doul's Old Milwaukee Old Vienna Pete's Portland Mactarnahan's Amber Portland Oregon Honey Pyramid Razors Edge Red Ale Red Dog Red Hook Red Wolf Rogue Dead Guy Ale Rogue Hazelnut Brown Rogue Red Rolling Rock Sam Adams Saranac Saxer Brewing Schmitt's Shiner Bock Ship Inn Shipyard Sierra Nevada Sleemans Southpaw Spanish Peaks Black Dog Starr Hill Brewery Steinlager Strohs Tecate Thomas Kemper Trois Pistoles Unibroue Wasatch Weinhard's Whitbread Ale Widmer Hefeweizen Woodchuck Dark & Dry Cider Wyder's Yuengling Zebra   Kegland Part number: KL06064

Read more less

Easily attaches to any Intertap faucet. Just unscrew the standard spout and replace it with this growler spout. Then you'll have a 1/2" (13mm) barb on the end of your faucet. Compatible with Intertap and NukaTap faucets. Stainless Steel Construction Kegland Part number: KL01038  

Read more less

The Pluto Beverage Gun is the ultimate hand held beer tap!  If you have been dispensing your draft beer out of a standard picnic tap, it's time to upgrade.  Definitely one of the coolest draft beer taps that we've seen, this Pluto Beverage Gun is made from nylon and stainless steel.  The body is plastic, while the barb, piston, and spring are all stainless.  Comes with a 1/4" duotight-compatible barb perfect for use with EVABarrier draft line. You will need either the 8mm x 6.5mm or 9.5mm x 6.5mm Duotight reducer to connect the EVABarrier to the Pluto. Kegland Part number: KL00956

Read more less

The Intertap faucet is a forward sealing faucet similar to the Perlicks. It has a modular, threaded spout which can fit a variety of different attachments including a growler filler or a stout spout. In normal rear-sealing faucets the entire faucet has to drain of beer. In forward-sealing faucets the faucet keeps beer in it so the inside doesn't have a chance to get sticky, making cleaning much easier. It also reduces the chance of off flavors transferring to your beer while you pour. Other forward sealing faucets use a floating o-ring, which is just as sanitary but requires the o-ring to move inside the faucet body in order to seal correctly. This can become a problem as the faucet ages. Intertap faucets use a sliding shuttle that guides the o-ring into the perfect position every time.  The threaded spout easily unscrews from the faucet and can be replaced by a growler filler or stout spout quickly and easily. Pour a pint and then fill a growler in no time at all. Made of chrome plated brass.   Kegland Part number: KL00987

Read more less

Narrow 0-25 psi operating range allows for fine-tuning and accurate dispensing of carbonated beverages Includes both Duotight and barb fittings for use with EVABarrier tubing or standard gas tubing Features a shutoff valve for safe operation and standard US CO2 tank threads (CGA320) Rubber gauge protectors safeguard gauges from potential damage Compatible with standard US CO2 tanks The KOMOS Dual Gauge Precision Dispensing Regulator provides precise control for dispensing carbonated beverages. Its narrow 0-25 psi operating range allows for finer pressure adjustments and greater accuracy compared to regulators with wider ranges. This design enables operators to easily fine-tune the output pressure within typical draft dispensing pressure settings. The regulator includes both Duotight and barb fittings for compatibility with EVABarrier draft tubing and standard gas tubing. The gas outlet features a shutoff valve for safe and convenient operation. Rubber gauge protectors are also included to safeguard the gauges from potential damage. Features: 0-25 PSI operating range Low pressure gauge reads from 0-30 psi Pull ring PRV rated to blow off at 25 psi Narrow pressure range for increased precision 1/4" & 5/16" barb fittings included Duotight adapter for EVABarrier tubing included Standard US CO2 Threads (CGA320) Shutoff valve Gauge protectors Ideal for dispensing carbonated beverages

Read more less

If you like serving out of commercial kegs but prefer the ease of using ball lock fittings in your draft system, this adapter is for you. Instead of buying additional keg couplers and beer thread to ball lock adapters, you can use this tapping head to go straight from sanke keg to ball lock. To install, remove the keg spear, place the gasket on the keg ferrule with the beaded side facing up, attach the silicone dip tube and place the tapping head on the ferrule, then secure with the 2" tri-clamp. Be sure to always depressurize the keg before removing the tapping head. Includes: Ball Lock Post Lid 2" tri-clamp Single-side beaded tri-clamp gasket 60 cm silicone dip tube (23.6") Red 2.5 bar PRV (36 psi) KegLand Part Number: KL10610    

Read more less