Swap out the standard BrewZilla recirculation arm with this flexible upgrade Perfectly position your recirculating wort or sparge water over the grain bed Use the BrewZilla's built-in pump to easily transfer wort to fermenter or clean the kettle with a CIP head This simple upgrade for the BrewZilla is perfect for positioning your recirculating wort or sparge water over the grain bed and makes it even easier to use the unit's built-in pump for transferring wort to your fermenter or for CIP at the end of the brew day. Pairs perfectly with the Sergeant Sparge Head for mashing and sparging, as well as the BrewZilla Spinning Spray Rotor to clean your kettle. Please note: Camlocks sold separately. You will need a Male Camlock x 1/2" Male Thread adapter in order to attach the Flexi Arm to your BrewZilla recirculation piping. Specifications: 304 Stainless Steel Fitted Female 1/2" Hex Nut Ends Silicone Washers Included Length 31.5" KegLand Part Number: KL15097
Use this lid along with the 35L BrewZilla or DigiBoil and a copper still top (DS120or DS130) to make your own easy-to-use distillery. This lid has a 1.85" (47mm) hole for the still top. Lid gasket included. Note: This lid uses a 6mm gasket to better fit the Gen 4 BrewZilla and Gen 2 DigiBoil. It is also backwards compatible with Gen 3 and older BrewZillas and Gen 1 DigiBoils. To improve the seal further, we highly recommend using the Adjustable Lid Clamps with the Distillation Lid if your unit does not have them. Made from 304 stainless steel Measures 12.25" in diameter. Kegland Part number: KL03483
Reduce heating time during your mash with the Gen 4 BrewZilla
Redistribute recirculating wort for longer heating element exposure
Improve heat distribution throughout the mash
Speed up heating times with the Heat Exchanger Dish (HED) for Gen 4 BrewZillas. This optional upgrade accessory redirects the flow of wort so that it spends more time exposed to the heating elements before reaching the center drain at the bottom of the kettle and being recirculated. Due to the concave bottom and central draining hole on the Gen 4 BrewZilla, recirculating wort will pass through the malt pipe and then down through the boiler false bottom following the path of least resistance. This can cause wort to make a B-line for the drainage hole and reduce the wort's exposure to the unit's heating elements. With the HED installed, wort will be directed to the edge of the BrewZilla base and pass over the elements for a longer period and reduce the time needed to heat to your set temperature.
For use with the Gen 4 65L BrewZilla. It is not compatible with any previous generations of BrewZillas or DigiBoils.
The HED has been pressed into a slight concave shape to match the curvature of the boiler false bottom. Includes a longer eye bolt assembly than the one included with the false bottom.
NOTE: The order of bolt to washer to nuts goes as follows. Eye bolt, washer, false bottom, washer, nut, HED, then wing nut. This is so that the eye bolt does not come completely removed when and if you clean underneath the Heat Exchanger Dish.
KegLand Part Number: KL29360
For use with the 35L BrewZilla Boiler Extension Kit. It does not come with an extra Wire Malt Pipe Support Ring. If you're using the extended malt pipe with the 35L DigiBoil, you will need to purchase the ring separately. If you're using the malt pipe with the 35L BrewZilla you can either move your ring up to the boiler extension, or buy an additional ring so you can remove the malt pipe in two steps. You will also need the Ricirculation Arm Extension to continue using the BrewZilla's recirculation arm. Compatible with Gen 3 / Gen 4 BrewZillas. KegLand Part Number: KL26468
Effortlessly transport your 35L or 65L BrewZilla or 65L DigiBoil with the sturdy rolling flat dolly, designed with precut hole configurations for secure placement Includes two locking wheels to hold your brewing system in place, ideal for cleaning on sloped surfaces or ensuring stability during use Perfect for Lift-N-Lock Pulley systems, enabling seamless movement under pulleys and convenient handling of malt pipes Easily move your BrewZilla or DigiBoil around your brewing area using this rolling flat dolly. The thick reinforced plastic dolly plate comes with two precut hole configurations suitable for 35L & 65L Gen 4 BrewZillas and 65L DigiBoils, allowing the feet of your system to slot into place for easy mobility. Two locking wheels are included so you can lock your brewery in place which can be especially useful if you move the unit to a sloped driveway for cleaning. These dollies are highly recommended if you are using a Lift-N-Lock Pulley type system for your malt pipe. Easily move your system into position under your pulley, and when you're done mashing, pull the malt pipe out, wheel the BrewZilla away, and lower the malt pipe to the ground or into a cleaning tub. The Low Profile Dolly Bundle is an economic choice recommended for 35L units and for brewers that have a relatively even surfaced brewing area with little to no obstruction. If you need something a little more rugged to handle uneven pavement or roll over power cords more easily, we recommend the Heavy Duty Dolly Bundle. Please take note that the bolts are pushed through from the bottom rather than top down. Compatible With: 35L BrewZilla Gen 4 65L BrewZilla Gen 4 65L DigiBoil Includes: Reinforced Plastic Dolly Plate 35 mm Castor Wheels (2 locking, 2 non-locking) Mounting Hardware Plate Dimensions: 21.6" Ø x 0.7" Thick (550 mm x 20 mm) BrewZilla sold separately
KegLand Part Number: KB11113 NOTE: Unfortunately due to the feet placement, the dolly plate is not suitable for the 35L Gen 3.1.1 BrewZilla or 35L DigiBoil.
This arm extension allows you to continue using the BrewZilla's recirculation arm after adding a boiler extension kit. Compatible with both 35L and 65L models.
Compatible with Gen 3 / Gen 4 BrewZillas.
KegLand Part Number: KL26413
This is a replacement BrewZilla PPSU Sight Glass tube. This is a one size fits all sight glass for multiple models and sizes. You will need to cut down the 39" PPSU tube to fit your specific model of BrewZilla depending on the length of the recirculation arm. We recommend purchasing the Pipe Cutter to cut the tube cleanly. If your unit did not already include the sight glass, Gen 3 and Gen 4 BrewZillas can be upgraded with one of these sight glass kits. See the video below showing you how to measure and install this on a BrewZilla. Specifications: 39.3" (100cm) Long 0.51" ID x 0.59" OD (13mm ID x 15mm OD) Temperature Rating: 356°F (180°C) KegLand Part Number: KL3380
NOTE: This accessory is designed exclusively for 3-vessel brewers who want to use the BrewZilla or DigiBoil as a mash tun. It is not meant to be used alongside a malt pipe, and it is not intended to be an upgrade or replacement to the BrewZilla's standard false bottom protection screen.
If you're a 3-vessel brewer and want to use the BrewZilla or DigiBoil purely as a mash tun, this is false bottom will give you more volume compared to mashing with a malt pipe. Designed for use with DigiBoil electric kettles or BrewZilla all-in-one systems. Unlike two-piece false bottoms you may find, this unit is welded together for maximum strength. It will easily withstand as much grain weight as you could possibly fit in the vessel. Features welded handles to easily remove the false bottom when cleaning.
Compatible with 65L DigiBoils and Gen 3/4 65L BrewZillas.
Dimensions:
Diameter: 15.35" (390 mm)
Height: 1.88 (48 mm)
Approximate Dead Space: 1.5 gal (5.7 L)
KegLand Part Number: KL27717
Replacement 6 Watt high temperature magnetic drive pump for 110V Gen 4 BrewZillas.
This pump is not backwards compatible with Gen 3 or older units.
KegLand Part Number: KL24358
This is a complete replacement silicone tubing kit for the pump and ball valve tubing on a 65L Gen 4 BrewZilla with 6 Watt Pump. Made from food grade silicone and temperature resistant to 356°F (180°C).
KegLand Part Number: KL24778
Replacement Ball Valve for the Gen 3 BrewZilla / DigiBoil. Silicone washer and stainless nut included, but not pictured.
Not compatible with BrewZilla Gen 4.
1/2" MPT
13.5 mm barb (apprx. 1/2")
304 stainless steel construction
KegLand Part Number: KL03728
This is a complete replacement silicone tubing kit for the pump and ball valve tubing on a 35L Gen 4 BrewZilla. Made from food grade silicone and temperature resistant to 356°F (180°C).
KegLand Part Number: KL27731
Add this neoprene jacket to your Gen 4 BrewZilla to speed up heating!
Heating is 10% faster and heat loss from the boiler is reduced by 50%
Remove the jacket after the boil to speed up chilling
Thick, insulating neoprene is secured to the boiler body with a sewn-on hook and loop fastener strap
Sparge arm sleeve included to reduce heat loss during mash recirculation
Add some insulation to your BrewZilla to get better boils! This neoprene jacket will help keep the heat in for quicker and more vigorous boils. Slap it on to speed up heating; take it off to speed up chilling. Also includes a neoprene sleeve for the recirculation arm to reduce heat loss during the mash.
This jacket will fit Gen 4 BrewZilla models. It is not compatible with older generations of BrewZillas and DigiBoils due to where the cutouts on the jacket are located.
Features:
10% faster heat up time
50% less heat loss from boiler
Fits the 100L BrewZilla Gen 4
Made from 8 mm thick neoprene which is easy to wash after use
KegLand Part Number: KL24389
Adjust clamp tension as needed for a better seal with metal BrewZilla or DigiBoil accessories If you're struggling to get an airtight seal when using the Distillation Lid or Steam Condenser Set, these clamps can help provide more tension Easily spin to adjust clamp height and then tighten hex nuts to lock in adjustment Compatible with 35L / 65L BrewZillas and DigiBoils Made from 304 Stainless Steel Get the exact tension you need with your BrewZilla or DigiBoil with KegLand's Stainless Steel Adjustable Clamp Set. Permanently replace the standard lid clamps and adjust the tension to your needs. These clamps are only intended for use with the metal Distillation Lid or Boiler Extension Kits. If you are having trouble getting the correct tension to form a good seal with those accessories, these adjustable clamps can help you dial in the fit. They should never be used with the standard glass lid. Compatible with 35L and 65L BrewZillas (Gen 3 / Gen 4), DigiBoils (Gen 1 / Gen 2), and Boiler Extensions. Installation Instructions: You will need a pair of bolt cutters or tin snips to cut the standard clamp off. (Please see product photos for optimum cut location). Remove the nut and bolt and thread it through the clamp. Ensure that the grooved part is facing outwards (photo for reference). If you do not have the grooved part facing outwards, the clamp will be blocked by the round lip of the boiler. Loosen the bolts and spin the clamp up or down to adjust the tension. Use the nuts to lock the desired tension. It is always best to start looser than you think, then adjust tighter. Warning: Do not use the adjustable clamps with a glass lid, the clamps are only designed for distillation lids or other metal accessories. Please note: The adjustable clamps will eventually phase out the standard lid clamps on all Gen 4 BrewZillas. They are not necessary when brewing with the standard glass lid. You should only swap to the adjustable clamps if you are using the metal distillation lid or boiler extensions and are having issues with getting the correct tension when using those accessories. KegLand Part Number: KL30649
Keep your beer taps clean and the fruit flies away with this beer faucet plug! Fits most standard beer faucets Made of highly resistant silicone These unique faucet plugs are designed to fit any faucet from 10 mm all the way up to 17 mm in diameter. These plugs are an economical solution to any fruit fly, yeast, or bacteria buildup when the faucet is not in use. The silicone is resistant to caustic and acid based cleaners as well as high temperature so they are dishwasher safe. This cap also functions as the stopper for the malt extension tube on the BrewZilla System. This cap will prevent grain from going down the tube. Kegland Part number: KL04220
Replacement handles for all BrewZilla Gen 4 glass lids. Also compatible with Gen 3.1.1 BrewZilla lids if you want to upgrade.
Sold as a set of 2.
KegLand Part Number: KL29537
This BrewZilla PPSU sight glass stainless steel ball valve and elbow use radial seal O-rings to form a strong, leak-free connection. Two in the ball valve and two in the bottom elbow. When assembling the sight glass to upgrade your existing Gen 3 or Gen 4 BrewZilla, you will reuse the female camlock x female 1/2" fitting that comes on the recirculation arm, or you need to purchase a separate fitting for the end of your custom build. You will also need plumbers tape or food grade Loctite to assemble the ball valve with the camlock fitting. Rather than purchasing the parts separately, Gen 3 and Gen 4 BrewZillas can be upgraded with one of these sight glass kits. KegLand Part Number: KL33817
Replacment malt pipe for the 65L BrewZilla Gen 4. This unit is not suitable for older generation BrewZillas or DigiBoils.
KegLand Part Number: KL32797
Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos.
This is a replacement silicone elbow bend for 35L or 65L BrewZillas. Compatible with Gen 3 and Gen 4. This part joins the pump to the inlet on the base of the BrewZilla then to the outlet of the pump to the recirculation arm on the side of the BrewZilla.
Made from food grade silicone. Temperature resistant to 356°F (180°C).
KegLand Part Number: KL06293
NOTE: This accessory is designed exclusively for 3-vessel brewers who want to use the BrewZilla or DigiBoil as a mash tun. It is not meant to be used alongside a malt pipe, and it is not intended to be an upgrade or replacement to the BrewZilla's standard false bottom protection screen.
If you're a 3-vessel brewer and want to use the BrewZilla or DigiBoil purely as a mash tun, this is false bottom will give you more volume compared to mashing with a malt pipe. Designed for use with DigiBoil electric kettles or BrewZilla all-in-one systems. Unlike two-piece false bottoms you may find, this unit is welded together for maximum strength. It will easily withstand as much grain weight as you could possibly fit in the vessel. Features welded handles to easily remove the false bottom when cleaning.
Compatible with 35L DigiBoils and Gen 3/4 35L BrewZillas.
Dimensions:
Diameter: 11.61" (295 mm)
Height: 1.77 (45 mm)
Approximate Dead Space: 0.79 gal (3 L)
KegLand Part Number: KL27700
Replacement ball valve for Gen 4 BrewZillas. The valve has been updated since the Gen 3.1.1 model as it has a different grooved tail end capable of accepting a 0.51" (13mm) radial seal barb and nut.
KegLand Part Number: KL31714
For use with the 65L BrewZilla Boiler Extension Kit. It does not come with an extra Wire Malt Pipe Support Ring. If you're using the extended malt pipe with the 65L DigiBoil, you will need to purchase the ring separately. If you're using the malt pipe with the 65L BrewZilla you can either move your ring up to the boiler extension, or buy an additional ring so you can remove the malt pipe in two steps.
You will also need the Ricirculation Arm Extension to continue using the BrewZilla's recirculation arm.
Compatible with 65L Gen 3 / Gen 4 BrewZillas.
Example image of the 35L model shown here.
KegLand Part Number: KL32834
This is the stainless steel immersion chiller that comes with the 35 L BrewZilla. Also suitable for use with the 35L DigiBoil. Use with D1710 1/2" ID beverage tubing.
Effortlessly transport your 65L or 100L BrewZilla or 65L DigiBoil with the sturdy rolling flat dolly, designed with precut hole configurations for secure placement Includes two locking wheels to hold your brewing system in place, ideal for cleaning on sloped surfaces or ensuring stability during use Perfect for Lift-N-Lock Pulley systems, enabling seamless movement under pulleys and convenient handling of malt pipes Easily move your BrewZilla or DigiBoil around your brewing area using this rolling flat dolly. The thick reinforced plastic dolly plate comes with two precut hole configurations suitable for 65L & 100L Gen 4 BrewZillas and 65L DigiBoils, allowing the feet of your system to slot into place for easy mobility. Two locking wheels are included so you can lock your brewery in place which can be especially useful if you move the unit to a sloped driveway for cleaning. These dollies are highly recommended if you are using a Lift-N-Lock Pulley type system for your malt pipe. Easily move your system into position under your pulley, and when you're done mashing, pull the malt pipe out, wheel the BrewZilla away, and lower the malt pipe to the ground or into a cleaning tub. This dolly bundle is also the preferred option for 100L BrewZillas and 65L BrewZillas/DigiBoils that use tall bulky distillation heads. Compatible With: 65L BrewZilla Gen 4 100L BrewZilla Gen 4 65L DigiBoil Includes: Reinforced Plastic Dolly Plate 100 mm Castor Wheels (2 locking, 2 non-locking) Mounting Hardware Plate Dimensions: 25.9" Ø x 0.7" Thick (660 mm x 20 mm) BrewZilla sold separately
KegLand Part Number: KB15697 NOTE: Due to the feet placement, the dolly plate is not suitable for the 35L BrewZilla or 35L DigiBoil.
