This optional lid is a great accessory if you want a more convenient way to move your Flat Bottom FermZilla around. Includes a silicone grommet for your airlock pre-installed.
This unique FermZilla lid piece does not require thread tape, o-rings or washers to form an airtight seal.
Please Note: This lid is not pressure rated.
KegLand Part Number: KL20848
Perhaps your wort was too hot when you transferred from the kettle, or while cleaning you dropped the FermZilla against something sharp that punched a hole, or maybe it's just time to replace the tank after acquiring too many scratches from normal wear-and-tear. Whatever the reason, no need to go buy a whole new FermZilla! Just pick up one of these fresh replacement tanks and your conical fermenter will be good as new! Pressure Stress If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple: Fill the tank to the brim with water Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher Pressurize the tank to 4 BAR (58 psi) Check for leaks, then replace the Red PRV when finished If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla. General Care Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank. KegLand Part Number: KL15226 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.
Perhaps your wort was too hot when you transferred from the kettle, or while cleaning you dropped the FermZilla against something sharp that punched a hole, or maybe it's just time to replace the tank after acquiring too many scratches from normal wear-and-tear. Whatever the reason, no need to go buy a whole new FermZilla! Just pick up one of these fresh replacement tanks and your conical fermenter will be good as new! Pressure Stress If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple: Fill the tank to the brim with water Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher Pressurize the tank to 4 BAR (58 psi) Check for leaks, then replace the Red PRV when finished If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla. General Care Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank. KegLand Part Number: KL15219 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.
Replacement PET Tank for the 55L Tri-Conical FermZilla with tri-clamp bottom port. Perhaps your wort was too hot when you transferred from the kettle, or while cleaning you dropped the FermZilla against something sharp that punched a hole, or maybe it's just time to replace the tank after acquiring too many scratches from normal wear-and-tear. Whatever the reason, no need to go buy a whole new FermZilla! Just pick up one of these fresh replacement tanks and your conical fermenter will be good as new! Pressure Stress If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple: Fill the tank to the brim with water Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher Pressurize the tank to 4 BAR (58 psi) Check for leaks, then replace the Red PRV when finished If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla. General Care Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank. KegLand Part Number: KL28257 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.
Replacement Lid O-Ring for FermZilla. Fits all models and sizes of FermZilla fermenters.
If you are experiencing leaking from the top lid section, this slightly thicker O-Ring will aid in resolving said leaking. To perform a leak test, please remember to have the unit free of any liquid as that will absorb CO2.
It is also important to remember not to overtighten the stainless steel handles that may have come with your FermZilla. Over-tightening will cause the opening to warp and not seal. The handles should be able to freely rotate around the neck with little resistance.
KegLand Part Number: KL22262
Weighted cap design keeps the dip tube submerged, maximizing liquid draw and minimizing air intake for consistent performance Prevents hop material and other sediment from clogging your dip tube, ensuring cleaner beer transfers and samples Works seamlessly with Torpedo Keg Buoys, Kegmenter Floating Dip Tubes, and FermZilla Pressure Kits for diverse brewing setups Made with food-grade HDPE and 304 stainless steel, allowing for easy cleaning and sanitization with common brewing cleaners This handy little filter attachment can be used with the Torpedo Keg Buoy, Kegmenter Floating Dip Tube, or FermZilla Pressure Kit to keep hop material from being sucked into the silicone dip tube. This upgrade accessory is especially helpful if you like to dry hop directly in your keg while serving, or if you want to pull clean samples from your FermZilla or Kegmenter during fermentation when there's still a lot of biomatter in solution. Simply remove the metal tube from the ball float, slip the silicone tubing over the barb, then reattach the ball float to one of three clip locations. Made from HDPE and 304 stainless steel, the filter can be boiled or sanitized with the full range of cleaners that we sell. The plastic HDPE is over molded onto the stainless mesh to make a seamless finish. The end cap can easily pop off for cleaning. This updated version of the original Filter Attachment now includes a weighted cap that helps keep the end of the dip tube pointed down and submerged below the liquid surface level. KegLand Part Number: KL41485
These handles are made from 304 stainless steel and held together with stainless steel bolts. Rated up to 220 lbs. Compatible with all sizes of FermZilla Conical, Flat Bottom, and All Rounder fermenters.
Kegland Part number: KL13079
This heating wrap provides excellent coverage for your FermZilla Conical, All Rounder, glass carboy, or PET fermenter. The large surface area ensures that heat is applied evenly to your fermenting beer. The 30-watt goes even further when paired with insulation and will lead to less temperature swings. It will provide plenty of heat while still being perfectly safe to use with plastic fermenters. And it features a convenient Velcro strap to hold itself in place—no need for electrician's tape that will leave gunky residue behind! For the ultimate temperature control with your FermZilla, pair the heat wrap belt with the Temp Twister Cooling Rod and control both heating & cooling with an Inkbird Temperature Controller. 110V plug. Approx. 39" x 9.75" KegLand Part Number: KL26048
Oxygen-Free Dry Hopping: Designed to allow dry hopping without exposing the batch to oxygen when used in combination with the 2" Hop Bong, 2" Butterfly Valve and additional accessories. Customizable with Accessories: Features undrilled ports for optional accessories such as the Temp Twister Cooling Coil and Thermowell, enhancing functionality and convenience. Improved WiFi Reading: The plastic lid improves KegLand RAPT Pill WiFi reading, ensuring better connectivity. Durable and Pressure-Resistant: Includes 4" and 2" Tri-Clamp ferrules, suitable for use up to 21 psi, with recommended PRV options for safe operation at specified pressures. Compatible with all Kegmenter Fermentation Kegs with 4" Tri-Clamp ferrule. See the Kegmenter Hop Bong Pressure Pack for a complete kit option. Upgrade your Kegmenter Fermentation Keg with this 4" Tri-Clamp Lid from KegLand. Add yeast, hops or even take samples from a wine thief from the top and not have to remove the entire lid. This particular lid was designed to address the growing desire to dry hop without exposing the batch to oxygen from opening the lid. By using this lid in conjunction with the FermZilla 2" Butterfly Valve and Hop Bong Kit, you will be able to purge CO2 into the tube and expel all the oxygen inside it and dump freely into the vessel. The lid features closed ports that can be drilled out to install optional accessories like the Temp Twister Cooling Coil and a Thermowell. The plastic lid also allows for improved KegLand RAPT Pill WiFi reading compared to the Kegmenter fully encasing the Pill in stainless steel. Due to the large 4" Tri-Clamp diameter, it is difficult to get higher pressures without leaking, therefore we suggest using the lid up to 21 psi. If you do not already own any of the Hop Bong fittings listed below, the Kegmenter Hop Bong Pressure Pack is also available as a complete kit. Features: (2) PCO1881 Male Ports Recommended for use with Red (Gas In) & Yellow (Bev Out) Ball Lock Caps PRV Port This should only be used with a Red 35 psi PRV or the Yellow 17 psi PRV. 2" T.C. Ferrule 4" T.C. Ferrule Undrilled Ports (for optional accessories): Thermowell Port (see below for FermZilla Thermowell kit) (2) Temp Twister Ports Please Note: Temp Twister will need to be bent on a 20° Angle in order to fit on the curved lid and align vertically in the tank. Hop Bong To use the Pressure Lid with the 2" Hop Bong, we recommend the following fittings if you do not have them already: 2 x Red Ball Lock Cap (FE13) 1 x Yellow Ball Lock Cap (FE146) 1 x 4" Tri-Clamp, 3 Segment Clamp (H734) 1 x 4" Tri-Clamp Seal (FF401) 3 x 2" Tri-Clamp (FF20) 3 x 2" Tri-Clamp Seal (FF201) 1 x 2" Butterfly Valve (FE198) 1 x 2" Hop Bong (FE202) 1 x 2" Hop Bong Cap (FE204) 1 x PCO1881 PRV Cap (KG523) 1 x Red 35 psi PRV (FE101C) Please note: The last product photo is an example image of what the lid looks like fully fitted out with the Hop Bong and other accessories that are not included with the lid.
Use this insulating jacket to regulate the fermentation temperature in your 55L FermZilla Conical. The jacket alone will help keep your fermenter warm in the colder months, or you can add a FermWrap heater if the heat fermentation isn't enough to maintain temp. Conversely, you can freeze bottles of water and put them inside the jacket to keep the temperature from getting too hot. If you're feeling extra fancy, use frozen water bottles and a FermWrap plugged into a temperature controller. The frozen water bottles will provide constant cooling, and if the controller detects that the temperature has dropped too far, it will kick on the FermWrap to heat your fermenter back up to your target temp. The jacket has the added benefit of protecting your fermenting beer from harmful UV light. Features a single sided zipper and draw string bottom. Kegland Part number: KL11495
If you've been looking to step up from fermenting in plastic buckets or carboys, this is an excellent choice for your next fermenter. Stainless steel is a much better option than glass or plastic, as it is extremely easy to clean and virtually lasts forever. There's also much less chance of contamination as stainless doesn't scratch like plastic. Over time, you'll get scratches in plastic fermenters from normal wear and tear, creating microscopic havens for bacteria. Meanwhile, glass carboys are always at risk of breaking which is something you will never have to worry about with stainless steel. The Bucket Buddy is a great value if you're looking for a stainless steel fermenter with built-in heating control. If you live in a cold climate, ale fermentations may be a seasonal affair, as cold ambient temperatures can easily drive down the temperature of your wort below your yeast's optimal fermentation temp range. The Bucket Buddy offers a simple solution with an integrated heating element and digital temperature control. Program your fermentation temperature and if the temp drops below your set point the unit will gently heat your wort from the bottom up via the concealed element located in the base. For cooling, you can place the fermenter in a dedicated refrigerator or drill into the lid to install a Temp Twister Cooling Coil. A temperature controller probe can then be taped to the side of the fermenter to control your cooling source, or you can drill another spot in the lid for a thermowell. Another advantage over carboys and plastic buckets is the domed base inside the fermenter which is great for yeast flocculation when fermentation is complete. The included racking arm will make it easy to transfer out every last drop of beer while leaving the yeast cake undisturbed. The entire racking arm and ball valve assembly is weldless, which means you can remove the assembly to clean and sanitize it between batches. You can even boil the assembly for added assurance that it's been sterilized. To help maintain a steady temperature and cut down on power consumption, the Bucket Buddy pairs well with either the BrewZilla Neoprene Jacket or the FermZilla Insulating Jacket. This unit comes standard with silicone tubing to transfer from the ball valve to your bottles or cans, as well as a stopper and airlock for the domed lid. Specifications: 304 stainless steel construction 9.25 gallon total capacity Digital temperature control 110V / 36W power Stainless steel outlet valve with rotating racking arm Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C External Dimensions: 28" H x 15" W (including handles) Internal Dimensions: 22" H x 11.75" W Please note: Heating capacity is highly dependent on ambient temperature and use of insulation. Testing has shown that the Bucket Buddy can heat to 104°F in a room temperature ambient environment without insulation. Adding insulation may increase heating capacity while colder ambient environments may lower heating capacity. KegLand Part Number: KL20695
The pressurizable Flex Chamber attaches directly to the X-Series Uni's butterfly dump valve and can be used for removing trub, harvesting yeast, and many other tasks. Designed for the BrewBuilt X-Series Uni Conical, but compatible with any 2" T.C. dump valve. Since the chamber is made from clear Tritan, it works perfectly as a sight glass for monitoring fermentation activity. Ball lock adapters can be attached to the threaded ports on either side, allowing you to connect oxygenation or carbonation stones, or flush the Flex Chamber with CO2 and use it to inject hops or other ingredients into your conical.
The Flex Chamber is also fully compatible with the Gen 3 FermZilla Tri-Conical fermenters. Not compatible with Gen 3.2.
2" T.C. connection
2" tri-clamp, gasket and end cap included
28 mm PCO 1881 threaded side ports
Chamber made from Tritan
Please note: never remove the Flex Chamber while your conical is under pressure. Always release pressure before removing the Flex Chamber.
Designed for use with the PCO38 Tapping Head. With female PCO1881 threads, it can also be used with the FermZilla Collection Container or Hop Bong Sight Glasses. The Red PRV is rated to 35 psi (2.5 BAR). Warning: Never exceed the pressure capabilities of your vessel. PRV's are not spunding valves! KegLand Part Number: KB10537
Elevate your brewing game with the 220V Gen 4 BrewZilla. This cutting-edge system combines more power with innovative features like wireless connectivity via WiFi & Bluetooth, allowing you to heat faster while you control and monitor your brew day, ensuring precision, convenience, and exceptional beer batch after batch!
WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal
The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench
Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter
Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation
Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency
Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp
The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve
Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps
More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet
WiFi/Bluetooth Enabled RAPT Controller
The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen.
But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability.
And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer!
But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings.
Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road.
High Capacity Malt Pipe
With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency.
Concave Base with Center Draining
Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind.
Ultra Low Watt Density Elements
The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy.
Easy Access Built-In Pump
The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet.
If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer.
MoreBeer!'s Final Word
We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included.
Perfect for Distillation
If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find.
Features:
Gen 4.1
Stainless steel construction
9 gallon total capacity with a finished beer output of 5-6 gallons
WiFi/Bluetooth Enabled RAPT digital temperature controller
Automatic step mashing with 6 programmable stages
220-240V power
NEMA 6-30P plug
Requires NEMA 6-30R receptacle
Requires 11 amps from 30 amp circuit
Dual heating elements (1900 watts and 500 watts)
Stainless steel 1/2" ball valve for gravity draining or transferring via pump
Immersion wort chiller included
Stainless steel malt pipe/basket
Stamped in volume markers
Glass lid
Adjustable lid clamps (do not use with glass lid in place - see below)
Magnetic drive pump for recirculation, transfers, and cleaning
Recirculation arm
PPSU sight glass
Bottom handle for easy lifting and pouring
Rubber feet
Temperature reads in °F or °C
Approximately 32.75" H (with recirculation arm) x 12.5" D
Recommended max. grain bill: 23.5 lbs
AlcoEngine Still ready with the purchase of a Distillation Lid
Pump Specs:
Max Capacity: 2.9–3.1 gal/min
Max Head: 4.9–6.8 ft.
Poles: 2
Voltage: 220–240V-AC
Frequency: 50–60Hz
Power: 6 watts
Current: 60 mA
Speed: 2600–3000rpm
Duty Cycle: Continuous
Capacitor: 2µF
Input/Output: 13mm barb
Water Resistance: IPX2
You Will Need:
2' of H985 1/2" ID Silicone tubing for sparging and draining.
To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950hose clamps and (1) brass hose by thread adaptor (H508).
These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout.
KegLand Part Number: KL27434
Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos.
Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe.
Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged.
Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.
35L (110V)
35L (220V)
65L (220V)
100L (220V)
10 ft.
14 Gauge
14 Gauge
12 Gauge
10 Gauge
25 ft.
14 Gauge
14 Gauge
12 Gauge
10 Gauge
50 ft.
12 Gauge
12 Gauge
10 Gauge
8 Gauge
RAPT Gen 4 BrewZilla | User Manual
Compatible with the 27L and 55L FermZilla Tri-Conical Series or any 2" or 3" T.C. fittings. This valve comes standard on the Tr-Conical FermZillas where the bottom of the tank attaches to the collection container.
KegLand Part Number: KL26505
Compatible with the 27L and 55L FermZilla Tri-Conical Series or any 3" T.C. fittings. This can be used on the bottom of your conical for a maximized dump valve or it can be used with a FermZilla T.C. Pressure Lid with 2" x 3" reducer and sight glass to make a massive hop injector.
KegLand Part Number: KL27571
Make your Gen 4 BrewZilla even smarter by pairing it with the RAPT Bluetooth Thermometer
Take mash temp readings from the top and bottom of your grain bed simultaneously
Set a temperature diffential between the readings to enable the BrewZilla RAPT controller to more accurately maintain temps and perform mash steps
Monitor coolant water temps during distillation runs and set alarms to alert you if the temperature is too high
Automatically log brew days with detailed information to your RAPT Portal account
Huge temperature range from -4°F to 572°F is easy to read on the backlit digital display
Orange backing plate can clip to the rim of your BrewZilla and is also magnetic
AAA batteries included
This low energy, RAPT-enabled Bluetooth Thermometer is compatible with the Gen 4 BrewZilla, RAPT Temperature Controller, and RAPT Fermentation Chamber. It will not work without one or more of these devices.
By receiving multiple BLE (Bluetooth Low Energy) thermometer sensors, the BrewZilla can make smarter and more automated decisions on how to control the brewing or distillation process. For example, the BLE thermometer probe can be put into the middle of the malt pipe so the BrewZilla can more accurately control elements switching on/off to achieve a core malt pipe temperature, or the thermometer can be placed into your coolant water during distillation runs so you get an alarm if the temperature is too high.
RAPT Connectivity
The new Bluetooth thermometer can connect up to your BrewZilla Gen 4, RAPT Temperature Controller, or RAPT Fermentation Chamber and log that temperature data and manipulate fermentation/brewing and distillation profiles in the RAPT Portal. This greatly reduces the need for handwritten records of your brew day as it's all done automatically. The RAPT portal also allows you to see every brew you have done in the past with logged temperatures from the main unit's probe and this digital thermometer. This unit can also be set up to send push notifications to your mobile phone of when it's time to begin sparging or begin other steps in your brewing process.
Along with this ease of access and control, the RAPT BrewZilla will also allow you to fully customize your brew day with profiles specifically tuned to your style of brewing or your recipe. For example, you could set up step mash profiles using the core temperature of your mash instead of the cavity below where the BrewZilla's main temp probe is located. Greater accuracy for a more repeatable recipe that results in much better beer!
Specifications:
Temp Range: -4°F – 572°F (-20°C – 300°C)
Probe Length: 8" (20 cm)
Note that the probe tip is very sharp
Remove black plastic tip before use
Plastic tip should be used for storage to avoid punctures / injury
Cable Length: 39" (100 cm)
Magnetized Backing Plate (Orange)
2 x AAA Batteries (included)
KegLand Part Number: KL24334
RAPT Bluetooth Thermometer | User Guide
Use this valve with a standard soda bottle as an inexpensive and effective dry hopping solution Attaches to the PCO 1881 threaded port on the FermZilla fermenter's lid Carbonation Cap and Tee Piece can be added to allow for purging the hops with CO2 This really handy stainless adapter ball valve will enable you to connect two PCO 1881 threads with a valve in between. Each side has an integrated O-ring that will seal on the neck of the PCO1881 Thread. Ideally suited to making a dry hop device for FermZilla with a standard soda bottle or PET growler with PCO 1881 threaded neck. As shown in the photo, if you use this stainless ball valve in conjunction with the PCO 1881 Tee Piece and the Carbonation Cap, you will have the added advantage of being able to use CO2 to purge out oxygen from the hops before you dry hop. This assembly makes an inexpensive and very effective dry hopping tool. Please note: Dry hop pellets will require a bit of a shake to get them to fall through the 3/4" bore. Tapping the PET bottle should be enough to make the hops fall down into the fermenter through the ball valve. KegLand Part Number: KL18074
Double-hinged for easier handling when connecting tri-clamp fittings
Textured tightening knob for better grip with wet hands
Hang the clamp by the knob on a peg board when not in use
This stainless steel tri-clamp features two hinges and folds into three pieces. Some brewers find this style of clamp easier to work with on large equipment that requires a 3" clamp. Direct replacement part to the clamp included on the FermZilla Tri-Conical fermenter.
KegLand Part Number: KL25799
Due to high demand, some of these items are currently out of stock but available for pre-order. Please check status notes below when selecting a size option to see if it is In Stock or tagged as PreBook. We will automatically ship this to you when we receive more inventory. Begin your homebrewing journey with an Electric Brewery! 9-gallon electric kettle saves space and can be upgraded later for all-grain brewing No expensive gas burner or heavy-duty brewing kettle required! Easy-to-use digital controller maintains your set temperature automatically Step-by-Step instruction pamphlet fine-tuned over 20 years for easy success The Premium Electric Homebrewing Starter Kit is one of the most approachable starter kits we’ve ever offered and represents the absolute best value you’ll find! The defining piece of this kit is the DigiBoil electric kettle. Most home brewing kits require a kitchen stove or outdoor propane burner, but with the DigiBoil you can make great beer just about anywhere you can find a power socket. The DigiBoil’s compact design makes this kit the ideal choice for those that want to brew indoors and not take up a lot of space. We also include the 6-gallon Fermonster fermenter, copper wort chiller, beer recipe kit of your choice, and all the time-tested brewing equipment you need to make beer at home. If purchased piece-by-piece this kit would cost well over $500, so you can feel confident that you’re getting all of the included equipment at the lowest price possible! Electric Brewing Typical home brewing starter kits set you up to brew your first batch of beer on the kitchen stove. This may lower the price tag but brewers will naturally progress beyond the kitchen to an outdoor gas burner or electric brewing system. Electric brewing systems have several advantages, firstly being that they do not require propane so there is no chance of running out of gas mid-brew. Secondly, electric kettles use a built-in temperature probe and digital controller to automatically maintain temperatures. This gives you a precise level of control that gas systems rarely match. Finally, the DigiBoil electric kettle is extremely compact and is the ideal choice for brewers that have space constraints or live in an area where brewing outdoors isn't an option year-round. 110V vs. 220V The DigiBoil electric kettle comes in two power options, 110 volt and 220 volt. The 110V unit features a standard 3-prong plug and will work with most US household power outlets. The 220V unit features a NEMA 6-30R plug, typically only used with large household appliances such as washer/dryer outlets. Both power options are perfectly suitable for brewing. The 110V option provides greater flexibility, allowing you to move your brewery from the kitchen to the garage, basement, or outdoor patio with ease. If you have convenient access to 220V power, the 220V model will significantly reduce heating times and provide a more vigorous boil. Extract Brewing Extract brewing is the simplest process for making beer and is therefore the most popular method for beginners. Powdered or liquid malt extract is added to water to make a sweet solution loaded with fermentable sugars that yeast will later turn into alcohol. The mixture is then brought to a boil and hops are added for flavoring. This simple method allows novice brewers to focus on learning the overall process of brewing while still making delicious beer. If you’re interested in all-grain brewing, check out the Premium Electric All Grain Home Brewing Kit. This version of the kit includes the DigiMash upgrade, which can always be purchased later when you’re ready to advance. The Fermonster Fermenter - A Huge Upgrade Over Standard Buckets or Glass "Carboy" Water Bottles Unlike buckets or glass carboys, the Fermonster fermenter was designed for brewing beer. It is made from tough, clear, virgin grade PET plastic so you can see the magic of fermentation. Unlike glass it will never break and shatter if dropped. It represents a huge upgrade over traditional buckets because these fermenters are much less likely to get scratched. Scratches can hold bacteria that can cause off flavors in the beer. The Fermonster comes with a built-in spigot that eliminates a long time issue in homebrewing of having to start a siphon to transfer your beer to the bottling bucket after fermentation is over. The large 4" lid allows for easily adding yeast, hops, or other additions. We also really love the molded-in level markers that tell you exactly when you have reached your desired volume. We Don't Skimp on Cleaning and Sanitizing Proper cleaning and sanitizing is one of the core tenants of making great beer. Some starter kits utilize an all-in-one cleaner/sanitizer that does neither job well. We’ve included the best-selling sanitizer for brewing, Star San. We also include Craftmeister oxygen-based cleaning tablets that make cleaning your Fermonster Fermenter a breeze. Other Upgrades That Make Brewing Easier We’ve also made a few items standard that really make the brew day easier including a thermometer for temperature monitoring and a hydrometer with testing jar for measuring sugar levels. Our reusable mesh bags allow for the easy removal of spent grain and hops at the end of the boil. The included stainless spoon is a really nice upgrade over plastic when you are stirring boiling liquids. Easy, How-To Instructions & an Actual 800# We've taught hundreds of thousands of people how to brew in over 25 years. Our instructions are clear and simple to follow and will have you making great beer with batch number one. If you have any questions, call our on-staff brewmasters at 1-800-600-0033. In an age where 800-numbers and real customer service is going away, you can still call us and ask a question. Recipe Options: American Ale produces a light colored, hoppy Pale Ale that puts the beloved Cascade hop on full display. Cascade hops are one of the classic American hop varieties, and we love them for their citrus, grapefruit character. Blonde Ale is a great starter beer for those who are new to craft beer. Blonde ales are an easy drinking ale, low in esters, balanced with enough hop character to accentuate the malt profile. American IPA is like a Pale Ale on steroids. Take a pale ale and add more malt, more grain, and more hops. Expect more alcohol and a more pronounced hop character. Brown Porter is a smooth, easy drinking beer. If you like maltiness emphasized with a hint of chocolate roastiness and subtle caramel nuttiness this is the beer for you. German Hefeweizen has a lovely blond color and distinct hazy appearance in the glass. This kit uses 100% Bavarian Wheat malt extract with just a dash of Northern Brewer hops for bittering. Haze Craze is our most popular New England IPA recipe kit. This Hazy IPA is packed with all of the hop character you'd expect from a classic West Cost IPA, but with much less bitterness and a much softer mouthfeel. This Kit Includes: 9 Gallon DigiBoil Electric Kettle w/ digital controller, stainless ball valve, internal volume markers 6 Gallon Fermonster fermenter with built in spigot, stopper, and airlock Neoprene jacket for quick heating Copper Wort Chiller for quick cooling Food Grade Bucket for bottling Mesh bags for hops on brew day or steeping grains for extract brewing A Thermometer for easy temperature management Hydrometer for making key sugar measurements Transfer Tubing Bottling Wand with shut off valve Sturdy Bottle Capper Bottle Caps Bottle Cleaning Brush Star San Sanitizer for true sanitizing Large Stainless Steel Spoon for mixing Craftmeister Cleaning Tablets for super easy cleaning Your choice of recipe kit with yeast included You Will Also Need: (48) 12 oz or (24) 22 oz cappable Beer Bottles or a Home Kegging System DigiBoil Specs: 110V or 220V Dual heating element control Digital temperature control Stamped-in volume markers (gallons & liters) 304 stainless steel construction Power Amps Element 1 Element 2 Plug 110V 15A 1000W 500W 3-Prong 220V 15A 1900W 500W NEMA 6-30R
We've seen a lot of all-in-one systems over the years, but none are as feature-packed and affordable as the BrewZilla. While other units simply maintain your set temperature, the BrewZilla features a sophisticated digital controller which can be programmed with a full mash schedule, executing each step automatically. The built-in pump will continuously recirculate wort during the mash for more even heat distribution and higher efficiency, but thanks to the integrated camlock fitting, it has even more functionality. Add the optional whirlpool arm to make your late hop additions pop and speed up chilling time, or connect a camlock fitting and tubing to transfer wort to your fermenter. These are just a couple of reasons why MoreBeer! loves the BrewZilla, but there are so many More!
Our Top 10 Favorite Features:
Sophisticated digital controller capable of programmed mash steps, boil addition timers and delayed start
Built-in pump for constant recirculation during mash or whirlpooling and transferring with optional accessories
Full depth malt pipe for higher mash efficiency and capable of running small batches without a pricey adapter
Multiple power modes to cover each step of the brew day – low power to gently heat your mash up to full power for a rolling boil
Wort chiller included! Perfectly sized for this system and adds even more value to your purchase of the BrewZilla
High capacity brewhouse – with a volume of over 9 gallons, you can fit more grain and more wort to make MoreBeer!
Single wall design doesn't trap in heat – chill your wort quickly after the boil!
Super convenient bottom handle makes lifting/pouring a breeze
Rubber feet keep the boiler lifted off the ground and safely above any spills that may occur
Affordable! This is the best price for an all-in-one brewing system you'll find, period.
If you want to jump into all grain brewing right from your first batch, or as an upgrade from malt extract brewing, the BrewZilla is a complete turn key solution. The BrewZilla is an all-in-one electric brewery that has built-in elements for heating and boiling, programmable mash schedule and delayed start, a built-in pump for recirculation, an onboard water resistant control panel for setting and monitoring temperatures, a removable grain basket, and a built-in spigot for transferring. It is extremely portable and uses 110V power so it can be used nearly anywhere.
The V3.1.1 unit features an upgraded main circuit board that changes how the automatic step mashing functions. Now when moving from step to step, the timer for each step will not begin counting down until the programmed temperature is reached. This means more accurate mash schedules than ever before! The new board also introduces boil addition timers so you'll never miss the mark for hop additions.
To get the Wort Chiller Connection Kit for free, add the item to your cart along with the BrewZilla and use code ZILLAKIT at checkout.
New accessory! Check out the BrewZilla Whirlpool Arm, which uses the unit's internal pump to recirculate and spin the wort, improving hop extraction and chill times. No more stirring!
Automatic Step Mashing & Delayed Start!
One of the coolest features of the BrewZilla is the ability to program the unit with up to 6 individual temperatures and durations so you can step mash precisely how you desire. Simply press the "S1-S6" button to select the stage you want to adjust, and use the temp, time and +/- buttons to program the stage. If you have less than 6 stages in your mash schedule, program the stages you want to skip with 00:00 as the time and the controller will automatically move on to the next step. When all the stages are complete, the unit will sound an alarm and hold the last set temperature.
The programmable stages can also be used to set a delayed start of up to 23 hours in advance so that you can have your water hot and ready to go when you get home from work or wake up in the morning. In order to do this, fill the unit with strike water and program the controller with two steps. Step 1 should be programmed at a temperature lower than the unheated strike water (so the elements will remain off), and the duration should be programmed for however long you want the delay. Then program Step 2 with your desired strike water temperature and a duration of 1-2 hours, giving the BrewZilla ample time to heat up and giving you a margin of error in case you hit the snooze button the morning of brew day.
Recirculating Mash with Full Depth Malt Pipe
The built-in magnetic drive pump easily recirculates wort during the mash. We recommend getting some silicone tubing to go with the recirculation arm. This allows you more control over the recirculation and you can then use the pump to transfer your wort to your fermenter. As with any mash, be sure to stir your grain very thoroughly after mashing-in so you start out with an even temperature throughout the grain bed.
Some competing models advertise their perforated malt pipes as "high flow", but what they don't mention is how this affects efficiency. When recirculating the mash, wort will escape through the side perforations rather than passing through the grain at the bottom-most end of the malt pipe which can lead to lower efficiency. The BrewZilla's malt pipe is designed so that recirculating wort must pass through the entire grain bed before escaping through the false bottom and being pumped over the top of the grain bed again. If you're worried about the flow rate, simply add a pound or two of rice hulls to your grain bill. This is especially recommended when brewing with a high level of wheat, oat, or flaked grains.
Power & Heating Control
Dual heating elements run off of a single 110 volt plug and have individual switches allowing for more control over the heating process. One element is 1000 watts and the other is 500 for a combined 1500 watts! Use both when you need to ramp up the temperature quickly either at the start to get to your mash temp or to go from your mash temp to boiling. Use only one of the elements when you want to hold a temperature.
We highly recommend adding the optional BrewZilla Neoprene Jacket to help reduce heating times and maintain a more vigorous boil. The extra thick neoprene jacket is custom designed to insulate the entire kettle portion of the BrewZilla while staying out of the way of the ball valve and handles. The jacket can help you acheive up to 10% faster heat up times and cut heat loss from the boiler in half. And when it comes time to cool your wort after the boil, simply remove the jacket! While other units boast a double wall design for better heat retention, this actually becomes a disadvantage when it comes to chilling.
The digital control panel makes it easy to see the current temperature and set the temperature you want. The digital controller is also water resistant so don't worry about spills or some water dripping down the side. This controller is built for brewing!
The brewery also includes a stainless steel malt pipe with false bottom allowing you to easily shift from mash tun to boil kettle during your brew day. The malt pipe includes a handle to lift it out and tabs at the base so you can set the malt pipe over the kettle to let the wort drain out. It also has feet at its base to raise the malt pipe slightly off the base and help prevent clogging.
The included stainless steel wort chiller is shipped with bare ends so you can set it up for your situation. We list below the most common tubing and fittings to connect to a hose, hose bib, or faucet.
What MoreBeer! loves about this product: Homebrewing is trending in the direction of all-in-one, all-grain brewing systems and the BrewZilla is the ultimate value. The cost is half of the next comparable system with programmable mash steps and nearly the same as buying converted coolers and a kettle. We've brewed on all the systems and we can truly say the BrewZilla is the easiest to use. We feel confident that a lot of first time brewers could buy this and use it with ease. At the same time quite a few of our experienced, all-grain brewing staff are buying it to brew at home. The unit is extremely compact because the pump is built-in to the bottom of the unit. You can move it around with ease which makes it perfect for guys and gals that have space constraints. Someone on the team also mentioned how they like that you can drain it via gravity without having to use the pump. All in all a great buy and highly recommended. Please note you will need a few extra pieces of hardware to connect the wort chiller and at least 2' of silicone tubing for the sparge.
Use the Pump for More Than Just Recirculation!
One of the surprisingly handy features of the BrewZilla is that the recirculation pipe features a female camlock. This allows you to hook up other accessories and use the unit's pump for more than just recirculating wort. With a male camlock and silicone tubing, for example, you can use the internal pump to push wort through a plate chiller or counterflow chiller. Check out our selection of camlock fittings here.
Features:
Gen 3.1.1
Stainless steel construction
9 gallon total capacity with a finished beer output of 5-6 gallons
Digital temperature controller
Automatic step mashing with 6 programmable stages
110V power and plug
Dual heating elements for total control (1000 watts and 500 watts)
Stainless steel 1/2 inch ball valve for draining (dont have to use the pump)
Immersion wort chiller included
Stainless steel malt pipe/basket
Stamped in volume markers
Glass lid
Magnetic drive pump for recirculation
Recirculation arm
Bottom handle for easy lifting and pouring
Upgraded rocker switches
Rubber feet
Temperature reads in °F or °C (press and hold temp button for several seconds to adjust)
32.75 in H (with recirculation arm) x 12.5 in D
Recommended max. grain bill - 18 lbs
Recommended min. grain bill - 8 lbs
AlcoEngine Still ready with the purchase of a Distillation Lid
You Will Need:
2' of H985 1/2" ID Silicone tubing for sparging and draining.
To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950hose clamps and (1) brass hose by thread adaptor (H508).
These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout.
Note: The manual references an element for a different market. This unit comes with two heating elements for a total of 1,500 watts.
Kegland Part Number: KL05838
How frustrating is it when hops cause blockage in your poppet, tap, ball valves and practically everywhere else? This really handy little filter can be used on with the Torpedo Keg Buoy or the floating dip tubes included with the Kegmenter and FermZilla Pressure Kit to prevent hops or other solids from getting sucked into the dip tube itself. The 304 stainless 80 mesh is fine enough to filter out hops and many other solids but not so fine that it gets blocked up easily. If you have a FermZilla or stainless Kegmenter this add is a must. Made from HDPE and 304 Grade stainless steel, this product can be boiled or sanitized in the full range of cleaners that we sell. The plastic HDPE is over molded onto the stainless mesh to make a seamless finish. The end cap can easily pop off for cleaning. Kegland Part Number: KL16957
This stainless ball valve has a PCO 1881 female thread on one side for attaching to the male thread on the FermZilla lid or collection container and a 3/4" BSP Female thread on the other side for attaching other fittings.
The 20mm bore (approx.) makes it possible to perform low oxygen dry hopping through the ball valve.
Ever wanted to punch out a few more gallons of wort with your 65L BrewZilla? Maybe you wanted more strike water for a super sticky batch. Maybe you get boil overs a lot and would like a bit of extra protection. Now there's a solution! The all new 65L BrewZilla Boiler Extension adds 6.3 gallons of headroom. Turn that 17G BrewZilla or DigiMash system into a 23G behemoth! The extension kit is also great for distilling! Extend the height of your pot still by attaching one or more boiler extensions. For distillation, we recommend upgrading to the Adjustable Lid Clamps which allow you to dial in the tension for a better seal. If you're struggling to get an airtight seal when using the Distillation Lid or Steam Condenser Set, these clamps can help provide more tension. Compatible with Gen 3 / Gen 4 BrewZillas. You Might Also Need: 65L Extended Malt Pipe 65L Wire Support Ring Recirculation Arm Extension KegLand Part Number: KL22248
Elevate your brewing game with the 220V 17 Gallon Gen 4 BrewZilla. This cutting-edge system combines more power & capcity with innovative features like wireless connectivity via WiFi & Bluetooth, allowing you to heat faster while you control and monitor your brew day, ensuring precision, convenience, and exceptional beer batch after batch!
WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal
The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench
Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter
Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation
Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency
Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp
The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve
Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps
More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet
WiFi/Bluetooth Enabled RAPT Controller
The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen.
But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability.
And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer!
But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings.
Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road.
High Capacity Malt Pipe
With an approximately 41.5 lb capacity, the BrewZilla can mash nearly 20% more grain than similar sized models of the Anvil Foundry and Grainfather G70. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency.
Concave Base with Center Draining
Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind.
Ultra Low Watt Density Elements
The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy.
Easy Access Built-In Pump
The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet.
If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer.
MoreBeer!'s Final Word
We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included.
Perfect for Distillation
If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find.
Features:
Gen 4.1
Stainless steel construction
17.1 gallon total capacity with a finished beer output of 10-12 gallons
WiFi/Bluetooth Enabled RAPT digital temperature controller
Automatic step mashing with 6 programmable stages
220-240V power
NEMA 6-30P plug
Requires NEMA 6-30R receptacle
Requires 16 amps from 30 amp circuit
Triple heating elements (2000, 1000 and 500 watts)
Stainless steel 1/2" ball valve for gravity draining or transferring via pump
Immersion wort chiller included
Stainless steel malt pipe/basket
Stamped in volume markers
Glass lid
Adjustable lid clamps (do not use with glass lid in place - see below)
Magnetic drive pump for recirculation, transfers, and cleaning
Recirculation arm
PPSU sight glass
Bottom handle for easy lifting and pouring
Rubber feet
Temperature reads in °F or °C
Approximately 36" H (with recirculation arm) x 16" D
Recommended max. grain bill: 41.5 lbs
AlcoEngine Still ready with the purchase of a Distillation Lid
Pump Specs:
Max Flow: 5 gal/min
Max Head: 11 ft.
Voltage: 220–240V-AC
Frequency: 50–60Hz
Power: 25 watts
Fittings: 1/2" (13 mm) barbs
You Will Need:
2' of H985 1/2" ID Silicone tubing for sparging and draining.
To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950hose clamps and (1) brass hose by thread adaptor (H508).
These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout.
KegLand Part Number: KL27458
Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos.
Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe.
Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories.
Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.
35L (110V)
35L (220V)
65L (220V)
100L (220V)
10 ft.
14 Gauge
14 Gauge
12 Gauge
10 Gauge
25 ft.
14 Gauge
14 Gauge
12 Gauge
10 Gauge
50 ft.
12 Gauge
12 Gauge
10 Gauge
8 Gauge
RAPT Gen 4 BrewZilla | User Manual
