KegLand is a high quality homebrewing equipment brand based out of Australia. We offer a wide variety of their products, from BrewZilla all-in-one system and DigiBoil eletric kettles, to pumps and grain mills. KegLand beer products are an incredible value, as they combine quality craftsmanship with low prices!
KegLand
-
Recirculation Arm Extension for Boiler Extension | BrewZilla | DigiBoil
This arm extension allows you to continue using the BrewZilla's recirculation arm after adding a boiler extension kit. Compatible with both 35L and 65L models. Compatible with Gen 3 / Gen 4 BrewZillas. KegLand Part Number: KL26413
$32.99
-
Boiler Extension Kit | BrewZilla | DigiBoil | 65L | 17.1G
Ever wanted to punch out a few more gallons of wort with your 65L BrewZilla? Maybe you wanted more strike water for a super sticky batch. Maybe you get boil overs a lot and would like a bit of extra protection. Now there's a solution! The all new 65L BrewZilla Boiler Extension adds 6.3 gallons of headroom. Turn that 17G BrewZilla or DigiMash system into a 23G behemoth! The extension kit is also great for distilling! Extend the height of your pot still by attaching one or more boiler extensions. For distillation, we recommend upgrading to the Adjustable Lid Clamps which allow you to dial in the tension for a better seal. If you're struggling to get an airtight seal when using the Distillation Lid or Steam Condenser Set, these clamps can help provide more tension. Compatible with Gen 3 / Gen 4 BrewZillas. You Might Also Need: 65L Extended Malt Pipe 65L Wire Support Ring Recirculation Arm Extension KegLand Part Number: KL22248
$65.99
-
FermZilla All Rounder Easy-Grip Pressure Fermenter Starter Kit | 7.9 gal. | 30 L
Crystal Clear super smooth PET makes fermenting and cleaning super easy Pressurizable for fermentation and closed transfer to your keg Includes BlowTie spunding valve kit, red & yellow carbonation caps, and floating dip tube as standard The FermZilla 30L All Rounder is the perfect fermentation vessel that can be used for fermenting under pressure, carbonating, and dispensing. It's far more capable than the FermZilla Flat Bottom but less complicated and less expensive than the FermZilla Tri-Conical fermenter. The key differences are that the All Rounder can be pressurized, unlike the Flat Bottom, but it does not have a dump valve like the FermZilla Tri-Conical. The FermZilla All Rounder Easy-Grip model comes packed with accessories so you can take full advantage of this pressurizable fermenter on day one. The new stock standard includes Easy-Grip threaded lid ring, BlowTie spunding valve with integrated pressure gauge, ball lock carbonation caps for the lid, and floating dip tube kit with weighted filter. What's Included: FermZilla 30L All Rounder Fermenter Hex Base with 24 x Sticky Dots (pre-attached) Easy-Grip Threaded Lid Ring Integrated Gauge BlowTie Kit Spunding Valve (0-15 psi) Silicone Dip Tube Kit with Yellow Weighted Filter and SS Float Red & Yellow Carbonation Caps Adhesive Thermometer Graduation Sticker Specs: 30 L (7.9 gal) Total Volume Pressure Rated to 2.5 Bar (36.2 psi) Height in Stand - 23" Tank Diameter - 14" Lid - 28 mm PCO 1881 threads Temperature Rating: When not under pressure, do not expose to liquids above 131°F When under pressure, do not expose to any temperatures above 95°F* *Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years. Kegland Part number: KL47272 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available below. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary. FermZilla All Rounder 30L & 60L | User Guide
$99.99
-
DigiMash Electric Brewing System | Gen 2 DigiBoil | 35L | 9.25G | 110V
The Gen 2 DigiBoil features two distinct updates that are not currently pictured in the primary images. The stainless steel lid has been upgraded to a glass lid, allowing you to observe and monitor boil activity. The rubber feet have been replaced with a plastic base that provides improved stability and slightly raises the unit for better ground clearance. Updated images coming soon. The most affordable all-in-one automated all-grain brewing system! Mash grains and boil wort in a single vessel DigiBoil electric kettle automatically maintains mash temperatures with the digital controller Dual heating elements combine for 1500W of power Also available with optional Recirculation Pump Kit! The DigiMash system represents the best value in electric all-grain brewing you'll find. With a 9-gallon DigiBoil electric kettle and the DigiMash stainless steel mashing accessory pack included, this is by far the most affordable way to get into electric all-grain brewing. It may not have all the bells and whistles of the BrewZilla, but it does have everything you need to mash and boil all in one unit. Setting up and using the DigiMash couldn't be easier. Simply place the false bottom inside the kettle and install the malt pipe, fill with water and heat to your desired strike temperature, then add your grain and set your desired mash temperature on the digital controller. Once your mash is complete, lift up the malt pipe, drain the wort and sparge, then remove the malt pipe and proceed to boil. If you're deciding between the DigiMash and the BrewZilla, there are a couple of key differences worth noting. One of our favorite features of the BrewZilla is the programmable mash steps and delayed start, which the DigiMash does not have. You can still step mash by simply raising the temperature manually on the controller, but the automatic steps are a convenient feature if you want to set it and forget it. The other major difference between the two systems is that the BrewZilla features a built-in pump for recirculating the mash. Recirculation is a great way to improve mash efficiency, but it is far from required for a successful brew day. Using an external pump with the DigiMash is also an option, and one can be integrated for mash recirculation quite easily. Simply connect the ball valve to the inlet of your pump, and then connect the outlet of the pump to our Sparge Arm Assembly. This model comes with the 35L DigiBoil, which has two built-in heating elements that run off a 110V plug. One element is 1000w and the other is 500w for a combined 1500 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage both elements to quickly go from mash temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s). Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach fittings with 1/2" FPT, such as our female threaded quick disconnect. DigiBoil Features: 304 stainless steel construction 9 gallon total capacity Digital temperature control 110V / 15A power and plug (5 ft. cord) Dual heating element control (1000w and 500w) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Stainless lid Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Recommended max. grain bill - 18 lbs Recommended min. grain bill - 8 lbs External Dimensions: 29" H x 15" W (including handles) Internal Dimensions: 19.5" H x 11.75" W ETL Listed DigiMash Stainless Steel Accessory Pack Includes: False bottom Malt pipe Wire support Malt pipe handle Malt pipe bottom screen
$299.99
-
4 in. Tri-Clamp Lid with Ball Lock Posts, PRV & Floating Dip Tube
This stainless 4" tri-clover ball lock lid is a direct replacement to the lid that comes on our kegmenters. Installation Note: For best performance, ensure there is not an excess amount of slack when the silicone dip tube is installed and shorten it if needed. With the floating dip tube installed on your empty Kegmenter, you ideally want the dip tube to hang freely with just enough length for the end of the dup tube to touch the bottom of the keg.
$60.99
-
Duotight Push-In Fitting - 8 mm (5/16 in.) Ball Valve
This Duotight ball valve can be used as an inline shut off valve on draft lines. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL06934
$3.89
-
BrewZilla Lift-N-Lock Pulley System
For all-in-one brewers and BIAB brewers, lifting the grains from your vessel can be daunting task. Give your back a rest and use the Lift-N-Lock pulley system to effortlessly lift up your grain bag or malt pipe and while your sweet wort drains into the kettle. This heavy-duty pulley is made from strong nylon strapping, laser cut 304 grade stainless steel and is capable of lifting large heavy loads with ease. It's the perfect pulley for lifting the heavy malt pipe from your BrewZilla or other all-in-one system, especially when brewing high gravity beers with a massive grain bill. It's a bit more expensive than other pulley systems, but there's no comparison when it comes to easily lifting or lowering the malt pipe. The included strap is 10m long by 25mm wide (32.8 ft. x 1 in.). The pulley system enables you to multiply your pulling force by 4 times. If you apply 60 lbs of pulling force, the pulley can lift 240 lbs with relative ease. Be sure that the beam you mount the pulley to is rated for the total amount of force being applied i.e. pulling force plus load weight, so for this example 300+ lbs. KegLand Item Number: KL30885
$76.99
-
BrewZilla Ultimate Combo Pack | Gen 4.1 BrewZilla All Grain Brewing System | WiFi/Bluetooth/RAPT Enabled | Neoprene Jacket, Hop Spider & Wort Chiller Connection Kit Included | 9.25G | 35L | 110V
The Ultimate BrewZilla Combo Pack! Get the Gen 4 BrewZilla & our most highly recommended accessories at an unbeatable price! Includes all of our favorite accessories for the BrewZilla including the Neoprene Jacket to speed up heating times, Hop Spider to keep vegetal matter out of your wort, and Chilling Connection Kit so you're ready to use the Immersion Chiller out of the box We think all BrewZilla brewers will eventually upgrade their systems with these accessories, so buy them together and reap the savings! Also available in 220V (AG583) Combo Pack Includes: BrewZilla Brewing System | Gen 4 | 9.25G | 110V Neoprene Jacket Hop Spider Wort Chiller Connection Kit Gen 4 BrewZilla All-in-One Brewing System WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 110-120V power and plug 12.5A Requires 20A circuit Dual heating elements (1000 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 110–120V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use. 35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge
$649.99
-
Malt Muncher Grain Mill - High Torque Motor
For the savvy DIY homebrewer with mechanical ability and electrical wiring knowledge, this high torque motor is perfect for motorizing your Malt Muncher grain mill. The motor is unique because it is sealed for safety and also features a built in gear reduction to produce the perfect output speed of 180rpm. A spider coupling for connecting mill shaft to motor shaft is included and will fit both 10 and 12 mm shafts. The picture shows how the motor is connected to the mill. Mill is not included. We do not provide wiring diagrams on how to connect electricity or an on/off switch so you may need to contact an electrician to complete your project. Features: 1 amp 110 v High Torque (1:7.5 ratio) Sealed housing making the motor almost maintenance free Measures 9.25 inches in total length Kegland Part Number: KL03278
$252.99
-
Insulated Cooler Mash Tun | Hot Liquor Tank | 14 gal.
If you're ready to step up to all grain brewing, this converted insulated cooler works wonders as a mash tun! The 14-gallon size can hold upwards of 25 lbs of grain, so there's plenty of room for even the strongest 5-gallon beer recipes and is perfect for most 10 gallon batches up to 1.070 SG. Comes pre-assembled with stainless steel perforated false bottom, high temperature silicone tubing, and 1/2" female threaded ball valve. Pair the valve with the male threaded fitting (plus a little plumber's tape) that best suits your setup and you'll off and running. The cooler also works perfectly as a Hot Liquor Tank. Use with the false bottom in place, or simply remove it and keep it on hand in case you decide to use the cooler as a Mash Tun down the road. Two of these coolers plus the Fermentap Sparge Arm Assembly work perfectly as a gravity fed all-grain setup. To connect the cooler's ball valve to the sparge arm assembly, we recommend a 1/2" MPT x 3/8" Barb fitting and 3/8" ID silicone tubing. Plumber's tape will ensure you have a leak-proof connection between the barb fitting and the ball valve. Includes: Insulated beverage cooler Max Volume: 14.7 Gal (56 L) Stainless dome-shaped perforated false bottom High temperature silicone tubing Stainless 1/2" BSP ball valve External Dimensions: Approx. 19" L x 19" W x 22" H KegLand Part Number: KL04671 Please note: the mash tun may come with a little extra silicone tubing than what's needed. Check that your false bottom is sitting flat and in the middle of the cooler and cut off excess tubing if needed.
$175.99
-
Duotight Push-In Fitting - 8 mm (5/16 in.) Tee
This Duotight fitting makes it easy to split your gas line and run it to multiple kegs. Use one tee for a dual tap kegerator or two tees for a triple tap. You can also pair the tee with the Push-In Pressure Gauge to use the gauge with the BlowTie Spunding Valve. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL02387
$3.29
-
Replacement Screw Caps for PET Beer Bottles - Pack of 24
KegLand's 500ml Amber PET bottles come with reusable screw caps, but these replacements are available if you prefer to use new caps with each bottling run. The locking ring is left behind on the bottle neck the first time the cap is screwed off, so if you're using fresh caps you'll want to remove the locking ring from the previous cap. These caps can also be used to replace the threaded caps included on the lid of the FermZilla fermenter. KegLand Part Number: KL25881
$4.99
-
Steam Condenser Set | 2 in. T.C. | BrewZilla | DigiBoil
Get to boil faster and increase boil vigor by retaining heat! Manage steam by turning it back into liquid that can later be used for cleaning/sanitizing Avoid the sticky residue that boiling wort can leave on your walls and ceiling Reduce the power consumption during the boil with your BrewZilla or DigiBoil Perfect accessory for indoor brewers! No need to install a special Range Hood to manage steam Made with the apartment and basement brewer in mind, this steam condenser set made from high quality 304 stainless steel will help you manage steam and condensation during the boil. Assembles in minutes and can be used with the BrewZilla or DigiBoil with the proper Distillation Lid and 2" T.C. weldless bulkhead. This setup will reduce heat loss, meaning you'll get to boil faster and use less energy overall to maintain a rolling boil. When it's time to add hops, yeast nutrients, or other additions, simply remove the tri-clamp end cap and drop them in. (Use gloves, it will be hot!). With the new Pro Sight Glass Distillation Lid, the condenser can be attached directly to the 35L unit's 2" T.C. ferrule or to the 65L unit's 4" T.C. ferrule using a 4" x 2" T.C. reducer. The Pro Distillation Lid also features a 3" sight glass disc that can be removed to address foaming issues or to add hops or other boil additions. If you've brewed indoors before, you're probably familiar with how sticky the evaporation coming off the boiling wort can be. The gummy layer of film it can leave behind on your painted walls and ceiling is no fun to clean up. And if you've been considering how to incorporate a range hood in your brewery to deal with the steam, now there's no need! Simply attach the Steam Condenser Set and run your kitchen tap or garden hose to the Duotight-compatible inlet. From the inlet, water will enter the column via a special spray head which can condense 0.42 gal (1.6 L) per minute while connected to 100 psi mains water. You'll find that a super-fast flow rate isn't necessary to cool boiling steam into liquid. Unlike the distillation process where the distillate needs to be under a certain temperature so that ethanol doesn't evaporate from the liquid at a high rate, with boiling wort you just need enough flow to form the steam back into liquid. Simple! After the steam is reformed into liquid, it will drain out of the bottom barb where you can install 3/8" ID silicone tubing. Recapture that water in a collection vessel and save it for cleaning and sanitizing! Once again, be aware that the water coming out will be very hot. Caution: You will need to remove the Steam Condenser when you reach boil to manage the hot break and ensure you don't have a boil over when you reach boiling temperatures. Once you've completed that step, you can reattach the Condenser and leave it in place for the remainder of the boil. Warning: It is important that the output tube for this steam condenser is open to atmosphere. This will allow the condensed steam to exit freely. DO NOT put a valve on the liquid output or restrict the condensed steam in any way as this may cause your brewery to develop vacuum and implode or explode. DO NOT immerse the tube for the condensed steam in water. The outlet hose must be open to atmosphere and the drips of condensed steam must drip into your collection bucket freely. You Will Also Need: Tri-Clamp Distillation Lid OR Standard Distillation Lid for 35L or 65L BrewZilla / DigiBoil With 2" T.C. Weldless Bulkhead (H707) OR Pro Distillation Lid for 35L or 65L BrewZilla / DigiBoil 35L Lid connects directly 65L Lid requires 4" x 2" TC Reducer 6.35 mm Monotight Adapter (or you can clamp directly to the inlet) 3/8" ID silicone tubing for the outlet Heat resistant brewing gloves Kit Includes: 5 x 2" Tri-Clamps 5 x 2" Tri-Clamp Silicone Seals 1 x 13.7" (340 mm) Long 2" T.C. Tee 1 x 7.8" (200 mm) Wide 2" T.C. Tee 1 x 2" T.C. End Cap 1 x 2" T.C. to 6.35 mm Duotight elbow cap with elongated spray head mister 1 x 2" T.C. x 0.47" (12 mm) Barb – Suitable for 3/8" (10 mm) ID Silicone tubing Some of these fittings are not sold separately NOTE: The kit does not include the Duotight adapter and garden hose QD shown in the example photo. The text in the photo showing the Duotight compatible inlet elbow states 6.5 mm; it is actually 6.35 mm. KegLand Part Number: KL22842
$186.99
-
BrewZilla Heat Exchanger Dish | HED | Gen 4 | 65L
Reduce heating time during your mash with the Gen 4 BrewZilla Redistribute recirculating wort for longer heating element exposure Improve heat distribution throughout the mash Speed up heating times with the Heat Exchanger Dish (HED) for Gen 4 BrewZillas. This optional upgrade accessory redirects the flow of wort so that it spends more time exposed to the heating elements before reaching the center drain at the bottom of the kettle and being recirculated. Due to the concave bottom and central draining hole on the Gen 4 BrewZilla, recirculating wort will pass through the malt pipe and then down through the boiler false bottom following the path of least resistance. This can cause wort to make a B-line for the drainage hole and reduce the wort's exposure to the unit's heating elements. With the HED installed, wort will be directed to the edge of the BrewZilla base and pass over the elements for a longer period and reduce the time needed to heat to your set temperature. For use with the Gen 4 65L BrewZilla. It is not compatible with any previous generations of BrewZillas or DigiBoils. The HED has been pressed into a slight concave shape to match the curvature of the boiler false bottom. Includes a longer eye bolt assembly than the one included with the false bottom. NOTE: The order of bolt to washer to nuts goes as follows. Eye bolt, washer, false bottom, washer, nut, HED, then wing nut. This is so that the eye bolt does not come completely removed when and if you clean underneath the Heat Exchanger Dish. KegLand Part Number: KL29360
$32.99
-
Heating Belt Fermentation Heater
This 30W Heating Belt will gently warm your fermenter without creating major hot spots. Heating belts are often chosen over heating pads for the simplicity of adjusting the height of the belt on your fermenter to increase or decrease the heat transfer. And they're especially useful for smaller vessels where a heating pad would be simply too large. For the best results, pair the Heating Belt with a temperature controller so that heating is only provided when your fermentation drops below your set point. If you're using a fermentation chamber or other form of chilling, the temperature controller will be able to switch between heating and cooling as needed. Comes with a standard 2-prong US style 110V plug. Please disregard the example photo that shows an AU style plug. KegLand Part Number: KL01953
$21.99
-
KegLand Oxebar Mono PET Keg | Ball Lock Keg | Floating Dip Tube | 5.2 Gallons | 20L
Getting into kegging has never been more affordable! Grab this 5-gallon ball lock keg for less than half the cost of a stainless corny keg of the same size! Transparent Oxebar Mono plastic makes it easy to see how much beer you have left in the keg. Especially handy when dispensing on the go Floating dip tube comes standard—a huge upgrade over traditional ball lock kegs. Draw the clearest beer inside the keg while leaving sediment behind Oxebar Mono Kegs are made from Nylon impregnated PET and Polyketone (POK) fittings for superior oxygen barrier properties compared to standard PET plastic Wedge seals on the Tapping Head and Ball Lock Caps eliminate points of oxygen ingress found where rubber is traditionally used Lower total oxygen pickup compared to a standard corny keg with silicone lid seal This 5-gallon keg is lightweight, compact and has high oxygen barrier properties with 3x better (meaning less) gas transmission than traditional PET grades of plastic making it suitable for beer storage or other oxygen sensitive carbonated and non-carbonated beverages. The included Ball Lock Tapping Head comes complete with Red & Yellow Ball Lock Caps for gas and beverage, floating dip tube with filter screen, and pull-ring PRV. Molded handles make it easy to remove the tapping head for cleaning and also allow you to stack the kegs on top of each other, even with your ball lock quick disconnects in place. Being made from the Mono Barrier PET Polymer Matrix, rather than stainless steel, this keg is lightweight and an ideal choice for draft dispensing on the go. But with all the key features of a standard corny homebrew keg, plus the added feature of the floating dip tube, the Oxebar Mono Keg makes for an affordable keg option for home dispensing as well. Fit up to 3 of these bad boys in a KOMOS Standard or Deluxe Kegerator, or fit up to 6 in the KOMOS Double-Wide Kegerator. Includes: 20L Amber Mono Barrier PET Oxebar Keg Dual PCO1881 Lid Assembly with Oxebar Black Handles Green Pull Ring PRV (65 PSI) Silicone Floating Dip Tube w/ Filter Attachment Red & Yellow Ball Lock Quick Disconnect (QD) Caps Specs: Height: 25.1" Diameter: 9.2" Volume: 5.28 Gallons Fit up to 3 kegs in the KOMOS Standard & Deluxe Kegerators NOTE: Oxebar Mono kegs are marked with a manufacture date. 2 years after production, and every 2 years after first use, it is recommended that the keg be hydro tested to ensure the keg is holding pressure. Hydro test instructions are below. You will also need a 100 PSI Gray PRV to perform the test. Fill the keg to the brim with room temperature water Replace the Green PRV with a Gray PRV rated to 6 BAR or higher Pressurize the tank to 6 BAR (87 psi) Hold the keg at 6 BAR for 1 minute Release the pressure and immediately remove the Gray PRV and swap back to the Green PRV If leaks or potential points of failure are found, replace the tank KegLand Part Number: KL36054 NOTE: Oxebar kegs are marked with a manufacturer’s “expiry date”. This does not indicate that the keg is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the keg be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the KG520 Tapping Head and D1072 Green PRV to perform the test. If you do not plan to pressurize the keg, the test is not necessary.
$49.99
-
Cannular Pro Chuck for Ball 300 End Crowler
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. Carbon Steel Chuck for Cannular Pro Semi-Auto Can Seamer. This chuck can be swapped in for the standard chuck so you can change from 16 oz or smaller cans to 32 oz Crowlers. Suitable for Ball 300 End aluminum crowler cans. This chuck is not compatible with the standard manual Cannular unit. KegLand Part Number: KL17763
$43.99
-
KegLand Warming Wizard Wand | Immersion Heater | 125 Watt | 2" T.C.
Low watt density heating element gently warms your fermenting beer without scorching Keep your fermentation temperature consistent during the colder months or raise the temp on command for diacetyl rests Connect directly to the BrewBuilt X3 Uni Conical via the dedicated 2" tri-clamp port for effective, in-solution heating Smooth, stainless steel construction is easy to clean after use Compatible with all sizes of X3 Uni Conicals Add this Immersion Heater to your BrewBuilt X3 Uni Conical for the ultimate control over your fermentation temperature. Connecting directly to the X3's dedicated 2" T.C. port at the side of the cone, the Immersion Heater will provide gentle, effective heating whenever you need it. A must-have for brewers living in colder climates or if you want the peace of mind that your temperature will never drop too low for your ale or kveik strains regardless of the time of year. Heating your fermenter on command can also come in handy if you need to bring your chilled wort up to temp before pitching, or if you need to perform a diacetyl rest after fermentation is complete. We recommend pairing the Immersion Heater with a temperature controller like the Inkbird so it will only be powered on as needed. If using the heater alongside the IceMaster Max 2 glycol chiller, you can insert the Max 2 temp probe into the X3's thermowell first and then insert the Inkbird's probe behind it. Both probes will be deep enough to get accurate temp readings and heating & cooling will be regulated by independent controllers. Another setup option is using the IceMaster 100 and the BrewBuilt Chiller Pump Kit. The IceMaster 100 does not come with built-in pumps so you can add your own submersible pumps as needed. Each Chiller Pump Kit includes an Inkbird controller and a submersible pump. The heater and pump are then both plugged into the Inkbird so heating & cooling are regulated by a single controller. The element runs at 125 watts when powered with the included IEC x 110V plug adapter (not pictured). Specs: 125W @ 110-120V (500W @ 220-240V) Total Length: 16" Length in Conical: 12" Cord Length: 5 ft. KegLand Part Number: KL35941 Please Note: The Warmking Wizard Wand is only compatible with X3 BrewBuilt Conicals. If interested in heating a previous generation conical, see the BrewBuilt Conical Heaters here.
$109.99
-
FermZilla Tri-Conical Butterfly Valve - 2 in. x 2 in. T.C.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. Compatible with the 27L and 55L FermZilla Tri-Conical Series or any 2" T.C. fittings. Primarily designed to be used with the FermZilla T.C. Pressure Lid and 2" Hop Bong for oxygen-free dry hopping. If you're planning on putting your FermZilla Tri-Conical or All Rounder in a Fermentation Chamber, you will want to allow for 420 mm (16.5") of clearance measured from the base of the ring collar to a comfortable level below the chamber ceiling so you can pull the PRV to purge oxygen from the hop bong. KegLand Part Number: KL27564
$43.99
-
Duotight Push-In Fitting - 8 mm (5/16 in.) Plug
This Duotight plug is used to block up your 8 mm (5/16") tees, elbows or other fittings for gas leak testing or simply to plug an unused section. Features: Insert plug and firmly push to connect Release plug by pushing in the collet on the Duotight fitting Suitable for both gas & beverage applications Made from food-grade acetal plastic Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number KL06958
$1.69
-
Retaining Circlip for Duotight Push-In Fittings - Pack of 10 - 8 mm (5/16 in.)
Duotight 8 mm OD retaining clip. Locks Duotight fittings in their closed position, making it impossible for any hose to escape. Pack of 10. KegLand Part Number: KL21517
$4.39
-
Mini Pressure Gauge (0-60 psi)
This mini pressure gauge is compatible with the BlowTie 2 spunding valve, Duotight in-line regulator, and KegLand mini regulator. We recommend using the gauge with a range closest to your desired pressure setting. If you'd prefer a digital instant read gauge, check out the Digital Mini Pressure Gauge (for gas applications only). Pressure Range: 0-60 psi (0-4 bar) Body Dimensions: 26mm x 26mm x 15mm Probe Diameter: 8mm WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Kegland Part number: KL15004
$7.69
-
Compression Fitting - 12.7 mm to 1/2 in. BSP
These compression fittings are the most common type to be used with immersion chillers on the market today. We highly recommend using these fittings on any and all immersion / ice bucket chillers to optimize the ability to quicky disconnect the liquid hosing for storage and ease of cleaning. The industry standard fittings are Camlocks which can be found here. These fittings have a pressure rating of 4500psi. Instructions: Tighen the fitting up finger tight. Mark the female and male threaded pars with a texter or marker. Further this fitting 1 and 1/4 turns to ensure correct compression has been achieved. KegLand Part Number: KL02004
$9.89
-
MaltZilla Motorized Grain Mill - Complete Kit
Everything you need to get right down to business with the MaltZilla Motorized Grain Mill! This complete kit includes the MaltZilla Grian Mill, Aluminum Hopper, PPE Base Board, and 110V Power Supply. KegLand put an exceptional amount of time into the research, testing, and development of the MaltZilla, and what they came up with is a motorized grain mill unlike anything we've seen before. It features an integrated motor so you'll never have to mess with a hand crank or power drill to spin the rollers. And the rollers themselves are made with a diamond-impregnated surface that offers superior performance and longevity compared to conventional knurled steel rollers. The integrated 24V motor is powerful enough to chew through popping corn kernels with ease, and works on voltages from 12-30V DC. The higher the voltage the faster the rollers spin, although we recommend 24V for optimum speed and grist results. The included power supply is straight forward, and allows you to plug the unit into a standard 110V power socket. Knurled Steel vs. Diamond Coated Rollers Your run-of-the-mill grain mills are often manufactured with steel rollers with a knurled finish. The knurling helps grip and pull the grain through the rollers, but even the knurling on hardened steel will go blunt eventually and hinder the mill's performance. Some manufacturers attempt to solve this problem by using geared rollers to better grab the grain, or add a third roller to the mill so the first two rollers with a larger gap force the grain into the third roller. These are only workarounds to the real issue—all steel rollers will go blunt eventually, especially if used with hard grains like wheat or corn. In a commercial setting, it’s not uncommon to send the rollers off to a metalworking factory to re-sharpen and re-knurl, but this is an expensive, time-consuming hassle. Many homebrew-scale users might just end up throwing the mill away and purchasing a new one. The MaltZilla Diamond Mill is quite a different mill design, and it’s the first in the world to use diamonds impregnated into the surface of the roller. Even after many tons of grain are processed through the mill, the diamond surface will stay just as sharp as it was on day one. The sharpness of the diamonds draws grain exceptionally well, and even when hard grains are used the diamond rollers won't dull or slip in performance. Sheer Instead of Chop Most mills require aggressive knurling to push into the grain and “chop” the grain as it passes through a tight gap, which means your grains are often chopped in half. The MaltZilla works on a different principle and gap setting is not as critical. The MaltZilla uses impregnated diamonds to grip the surface of the kernel and the friction of pulling the grain through the gap causes a sheering action. When set up correctly, the sheering action can leave the entire husk intact, reducing the chance of stuck sparge and improve efficiency, while still opening the husk enough that the entire contents of the kernel is available to the mashing process. The 70 mm diameter rollers are double the diameter of many other mills, which significantly improves the crush and assists in drawing the grain in more effectively. Integrated Motor You generally would not purchase a car without an engine, so why would you purchase a grain mill without a motor? Milling grain has an optimum RPM— too slow and it will take you a long time, too fast and you will end up with excessive powder. Hand cranking can be a pain in the backside, especially with larger grain bills, and using a power drill doesn't offer much in the way of speed control and adds the potential risk of burning out your drill. The MaltZilla has an integrated motor with a very constant RPM putting out optimum RPM with an integrated gearbox. The high torque and sealed construction make it ideal for a brewing environment, as the motor is well protected from moisture and grain dust. The motor is seamlessly integrated into the side body of the mill. Being DC, the motor is safer than higher voltage AC, especially in an environment where splashing and hose spray are commonplace. The DC motor is also reversible so the direction of spin can be changed based on the polarity. This is particularly useful for over-mount and under-mount installation. Kit Includes: MaltZilla Grain Mill (12-30V DC) Power Supply (110V) Polypropylene base baord Aluminum hopper 6-gallon plastic bucket 17-blade gap thickness measuring tool Please note: This mill is designed for use with brewing grains only. It will not work for cracking whole kernel corn.
$384.99
-
Replacement Airlock Cap for FermZilla Lid
Replacement black PCO1881 cap for the FermZilla lid. This is the cap with airlock hole and grommet. For the solid cap, see here.
$2.19
-
EVABarrier Double Wall Draft Tubing | Transparent Red | 5 mm ID x 8 mm OD
Easily identify gas and beverage lines with color-coded options—LightShield Black for beverages, Transparent Red for gas EVABarrier's double-walled design with a proprietary inner polymer significantly reduces oxidation and CO2 loss, keeping your beer fresher for longer The ultra-smooth, nearly impermeable inner surface of the tubing prevents bacteria and microbes from adhering, ensuring cleaner beer lines The stiff yet pliable EVA outer barrier makes the tubing kink-resistant and ideal for use with push-in fittings like Duotight and John Guest Red is recommended for differentiating your gas lines, but the 5mm ID is the perfect size if longer 10-12 ft. beverage lines are needed Easily identify your gas and beverage lines with color-coded draft tubing. Transparent Red EVABarrier is recommended for gas lines while using LightShield Black for your bev lines, saving you a headache when your draft lines inevitably get tangled up in your draft system. The semi-transparent red outer barrier makes the tubing easy to recognize even with minimal light. If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. If you wish to use the tubing for beverage rather than gas, we recommend using 10-12 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 5 mm (13/64") Outer Diameter - 8 mm (5/16") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. KegLand Part Number: KL42741
$28.49 - $185.99
-
Stainless Tri-Clamp Sample Valve Shank | 1.5 in. T.C. x Beer Faucet Shank | Intertap® | NukaTap®
Standard, plunger-style sample valves can be a bit of hassle when it's time to check your gravity or do a taste test. Replace it with this simple T.C. x Draft Shank adapter which allows you to pour samples with your preferred beer faucet. We recommend using the NukaTap Flow Control Faucet with Self-Closing Spring. This will allow you to put some restriction on the beer flow and come in very handy when taking samples from a pressurized conical or brite tank. Also compatible with Intertap, Perlick, and other faucets. Please note: standard NukaTap SS Faucet and Self-Closing Spring will not work with this shank. You can use a NukaTap SS faucet, but without the autoclose spring. Specifications: 2.75" total length Standard shank assembly 1.5" T.C. connection KegLand Part Number: KL19989
$21.99
-
BrewZilla | DigiBoil | Adjustable Lid Clamps | Stainless Steel | Set of 4
Adjust clamp tension as needed for a better seal with metal BrewZilla or DigiBoil accessories If you're struggling to get an airtight seal when using the Distillation Lid or Steam Condenser Set, these clamps can help provide more tension Easily spin to adjust clamp height and then tighten hex nuts to lock in adjustment Compatible with 35L / 65L BrewZillas and DigiBoils Made from 304 Stainless Steel Get the exact tension you need with your BrewZilla or DigiBoil with KegLand's Stainless Steel Adjustable Clamp Set. Permanently replace the standard lid clamps and adjust the tension to your needs. These clamps are only intended for use with the metal Distillation Lid or Boiler Extension Kits. If you are having trouble getting the correct tension to form a good seal with those accessories, these adjustable clamps can help you dial in the fit. They should never be used with the standard glass lid. Compatible with 35L and 65L BrewZillas (Gen 3 / Gen 4), DigiBoils (Gen 1 / Gen 2), and Boiler Extensions. Installation Instructions: You will need a pair of bolt cutters or tin snips to cut the standard clamp off. (Please see product photos for optimum cut location). Remove the nut and bolt and thread it through the clamp. Ensure that the grooved part is facing outwards (photo for reference). If you do not have the grooved part facing outwards, the clamp will be blocked by the round lip of the boiler. Loosen the bolts and spin the clamp up or down to adjust the tension. Use the nuts to lock the desired tension. It is always best to start looser than you think, then adjust tighter. Warning: Do not use the adjustable clamps with a glass lid, the clamps are only designed for distillation lids or other metal accessories. Please note: The adjustable clamps will eventually phase out the standard lid clamps on all Gen 4 BrewZillas. They are not necessary when brewing with the standard glass lid. You should only swap to the adjustable clamps if you are using the metal distillation lid or boiler extensions and are having issues with getting the correct tension when using those accessories. KegLand Part Number: KL30649
$13.49
-
NukaTap® Stainless Steel Beer Faucet | Flow Control Gen 2 | Forward Sealing
G2 model features redesigned flow control mechanism for improved shank sealing and flow control Make instant adjustments to beverage flow as you pour Switch from pouring pints to filling growlers without adjusting your CO2 regulator Reduced first pour foam due to low thermal mass Forward-sealing design prevents beer residue from gumming up the faucet Unique shuttle design greatly improves laminar flow, improving the pour of carbonated beverages Compatible with all Intertap faucet accessories and shanks Generation 2 The NukaTap Flow Control G2 uses a completely new flow control mechanism with better sealing properties against the shank as well as improved flow control. Control the Flow The flow control model is a great option for users that often switch between beer styles with different carbonation levels. No need to rebalance your lines or play with your regulator settings. Instantly make adjustments as you pour to dial in the flow rate. This is also a super convenient feature for when you want to grab a quick growler on your way out. By dialing back the flow rate, you can gently fill your growler so CO2 stays in solution and your beer doesn't pour flat when it comes time to share. The NukaTap Flow Control faucet is also the first FC model to be fully compatible with the optional self-closing spring. First Pour Foam Reduction Every kegerator owner knows the letdown of pouring your first pint of the day and getting too much foam. Even with perfectly balanced draft lines, first pour foam is sometimes unavoidable simply due to the temperature of the faucet itself. Running beer through the faucet will drop the temperature, and the foaming will subside, but not without a bit of wasted beer from pouring off excess head. The NukaTap beer faucet drops to beer serving temperature much faster thanks to its lower thermal mass. Simply put, the bulkier the faucet is, the more beer is needed to flow through and chill the tap. The NukaTap is over 20% lighter than its Intertap predecessor, and even lighter still compared to other brands of faucets. Improved Laminar Flow The inspiration for the NukaTap name comes from its uniquely designed "nuke-shaped" shuttle that resides on the inside of the faucet. The NukaShuttle went through numerous rounds of redesigns and countless hours of testing to find a shape that provides superior laminar flow. This means that liquid passes by the shuttle with very little resistance, allowing highly carbonated beers or hard seltzers to pour like a dream. Sanitary Design The NukaShuttle is the world’s first seamless single-piece design. Traditional taps feature an o-ring seated on a stainless steel shuttle, which can cause a couple of issues. After many pours, the stainless shuttle rubbing against the internal body of the faucet will create small fissures that become potential infection sites, and the seated o-ring can be difficult to clean in place, making your draft cleaning and sanitizing process less effective than you realize. The NukaShuttle is an advanced TPV rubber matrix that has been seamlessly formed over a durable PP skeleton. This single-piece design eliminates the pitfalls of older manufacturing methods, making it one of the most sanitary faucets on the market. Forward Sealing vs. Rear Sealing From tap rooms to home bars, forward-sealing faucets are the ideal choice for any draft setup. In traditional rear-sealing taps, beer will drain out of the entire faucet when it's in the closed position. This means the internal mechanism is coated in beer, which then dries and becomes a sticky residue. Forward-sealing faucets, on the other hand, keep the tap full of beer so it never has a chance to dry and gunk up the internal parts. This makes the faucet much easier to clean and also reduces the chance of off flavors transferring to your beer while you pour. Made from stainless steel Shuttle made from TPV O-rings made from EPDM Kegland Part Number: KL15523
$59.99
-
BrewZilla PPSU Sight Glass Upgrade Kit
Upgrade Gen 3 and Gen 4 BrewZillas with a clear sight glass to monitor volume levels throughout your brewing process Replaces the solid metal recirculation pipe so you can check volume levels even while the malt pipe is draining The PPSU sight glass now comes standard on Gen 4.1 BrewZillas *Requires measuring, cutting, and assembly* This upgrade kit is suitable for BrewZilla Gen 3 and Gen 4 breweries. This will enable you to see the liquid level through the incredibly strong and crack resistant PPSU sight glass. This can be quite handy when you're sparging to a known level as the malt pipe would normally be sitting on top of the halo ring making it difficult to see the liquid level from the indentation markings inside the BrewZilla. Assembly Required: You will also need plumbers tape or food grade Loctite for the female camlock x female 1/2" fitting that comes on the BrewZilla's recirculation arm. The BrewZilla's camlock fitting is reused in the assembly of the sight glass, do not dispose of it prematurely. Please note: This kit includes a one size fits all sight glass for multiple models and sizes. You will need to cut down the 39" PPSU tube to fit your specific model of BrewZilla depending on the length of the recirculation arm. We recommend purchasing the Pipe Cutter to cut the tube cleanly. See the video below showing you how to measure and install this on a BrewZilla. Includes: Brewzilla Sight Glass PPSU Tube - 39.3" (100cm) Sight Glass Connection Kit (Ball valve & Elbow) Sight Glass Graduation Sticker for 35L, 65L or 100L
$43.99
-
Duotight Push-In Fitting - 8 mm (5/16 in.) x 1/4 in. BSP
This Duotight fitting with 1/4" male thread is a great option for connecting gas line to regulators and manifolds that have 1/4" FPT. Comes with seated O-ring. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL06897
$3.29
-
Heavy Duty Dolly Bundle | Flat Dolly | 35L & 65L BrewZilla Gen 4
Effortlessly transport your 35L or 65L BrewZilla or 65L DigiBoil with the sturdy rolling flat dolly, designed with precut hole configurations for secure placement Includes two locking wheels to hold your brewing system in place, ideal for cleaning on sloped surfaces or ensuring stability during use Perfect for Lift-N-Lock Pulley systems, enabling seamless movement under pulleys and convenient handling of malt pipes Easily move your BrewZilla or DigiBoil around your brewing area using this rolling flat dolly. The thick reinforced plastic dolly plate comes with two precut hole configurations suitable for 35L & 65L Gen 4 BrewZillas and 65L DigiBoils, allowing the feet of your system to slot into place for easy mobility. Two locking wheels are included so you can lock your brewery in place which can be especially useful if you move the unit to a sloped driveway for cleaning. These dollies are highly recommended if you are using a Lift-N-Lock Pulley type system for your malt pipe. Easily move your system into position under your pulley, and when you're done mashing, pull the malt pipe out, wheel the BrewZilla away, and lower the malt pipe to the ground or into a cleaning tub. The Heavy Duty Dolly Bundle is highly recommended for 65L BrewZillas and outdoor brewers that have uneven surfaces. If you're using the 35L unit and looking for a less expensive alternative, check out the Low Profile BrewZilla Dolly Bundle. Compatible With: 35L BrewZilla Gen 4 65L BrewZilla Gen 4 65L DigiBoil Includes: Reinforced Plastic Dolly Plate 100 mm Castor Wheels (2 locking, 2 non-locking) Mounting Hardware Plate Dimensions: 21.6" Ø x 0.7" Thick (550 mm x 20 mm) BrewZilla sold separately KegLand Part Number: KB11089 NOTE: Unfortunately due to the feet placement, the dolly plate is not suitable for the 35L Gen 3.1.1 BrewZilla or 35L DigiBoil
$109.99
-
Step Drill Bit | Self-Starting | HSS High Speed Steel | Titanium Nitride Coated | 0.15 – 0.78 in.
If you want to install the Temp Twister & Thermowell on your FermZilla's plastic lid, this step drill bit is the recommended tool for the job. Suitable for drilling holes in plastic, wood, stainless steel, and other metals. You can use this drill bit to install valves or bulkheads on a stainless kettle, bore out a hole for a draft shank, or drill out the pilot hole found on many KegLand drip trays. For best results when drilling through metal, make sure to drill slowly (less than 600 rpm). Apply significant pressure behind the drill as you cut through. Cutting lubricant is recommended. Note that fast drill speeds will cause the metal and the bit to heat up which can shorten the lifespan of the drill bit. Specs: Drill Speed: 200-800 RPM Can Drill Hole Sizes: 4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm, 22mm Hole Size Range (Imperial): 0.15" – 0.78" Coating: Titanium Nitride Suitable for: Metal, wood, plastic Tip: Self starting tip (no pilot hole required or center punch) KegLand Part Number: KL09447
$10.99
-
KegLand MKII Magnetic Drive Pump | Center Inlet Pump Head | Stainless Steel | 13.5 GPM | 65 Watt
Please note: the example images show an AU style 220V plug. This unit comes with a standard US 3-prong 110V plug. Updated images coming soon. The "Big Brother" to one of our best-selling pumps! Expect the same quality that customers have come to expect from the MKII Pump (PMP50) but with more power. This 65 watt magnetic drive pump is powerful enough for homebrewers and micro brewers alike. Use it to move hot wort in an all-grain system and also to transfer wort from boil kettle to fermenter. The pump head is made from 304 grade stainless steel with 3/4" threaded ports that can easily be converted to tri-clamp. The magnetic drive allows you to slow down the flow without damaging the pump. This pump is not self-priming so do not run the pump dry. The pump head can be rotated in 60-degree increments, allowing for 6 different pump head orientations. We recommend adding two 1.5" T.C. x 3/4" Female BSPP adapters to the ports. From there you can use a ForgeFit 1.5" T.C. x Male QD to use quick disconnects with your lines, or convert to your preferred tri-clamp fittings. Features: 110V / 60hz Max Head: 15-21 ft. Max Flow: 13.5 Gal/min Max Temp: 248°F (120°C) Rotatable 304 stainless steel pump head 3/4" BSPT fittings Water resistant casing KegLand Part Number: KL05487
$219.99
-
Hop Bong Cap - PCO1881 Male x 2 in. T.C.
For all you hop bongers out there. We have an end cap for all end caps! Compatible with multiple PCO1881 accessories. Made from high quality engineering plastic and will last a very long time. It's chemically resistant and also designed to resist impact and physical damage. The Hop Bong features a molded PCO1881 port, but depending on your application you might need a second. If using to dry hop, you'll use the Hop Bong port to add CO2 with a Ball Lock Cap and then attach the PRV Cap to the Hop Bong Cap to purge the gas. Use with the 2" Hop Bong to attach: Red PRV 1881 Cap Combo Red Ball Lock Cap Yellow Ball Lock Cap KegLand Part Number: KL23627
$4.39
-
BrewZilla All Grain Brewing System | Gen 4.1 | Integrated Pump | Includes Wort Chiller | WiFi | Bluetooth | RAPT | 35L | 9.25G | 110V
Elevate your brewing game with the Gen 4 BrewZilla. This cutting-edge system combines innovative features like wireless connectivity via WiFi & Bluetooth, allowing you to control and monitor your brew day, ensuring precision, convenience, and exceptional beer batch after batch! WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain -- get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don't overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you'd prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you'll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you'll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone -- all of the data from your brew is automatically logged to your portal profile. This information doesn't just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn't just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone's web browser. Not sure when you'll be home from work or your kid's ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We've all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there's more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you'll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller's firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery's grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you'll be able to extract every last drop of wort to your fermenter. If you've brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you'll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you'll find on the controller is adjusting the pump flow. This doesn't control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it's an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you'll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don't have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We've been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it's also offered at an incredibly competitive price point when compared to other systems. You'll get all of the cutting edge Bluetooth technology you'd get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that's yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you'll need to spend another $100 for the recirculation pump kit. What's more, no other system in the same 'weight class' has the same grain capacity. And if the standard capacity isn't quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you're investing in a top shelf system and all of the critical features you're expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 110-120V power and plug 12.5A Requires 20A circuit Dual heating elements (1000 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 110–120V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 You Will Need: 2' of H985 1/2" ID Silicone tubing for sparging and draining. To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950hose clamps and (1) brass hose by thread adaptor (H508). These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout. KegLand Part Number: KL3276 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use. 35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge RAPT Gen 4 BrewZilla | User Manual
$599.99
-
Stainless Tri-Clamp Sight Glass | 1.5"
Monitor fermentation activity in a stainless steel conical Check flow and liquid clarity during transfers Harvest yeast and store with end caps Keep an eye on the flow during transfer or monitor yeast activity during fermentation with this 1.5" tri-clamp sight glass. Place the sight glass in-line when you transfer wort from kettle to fermenter to help you oversee how your in-line oxygenator is flowing. One of the few disadvantages of a stainless steel conical is that you can't watch the yeast as they go to work. With a sight glass you'll be able to observe how your yeast are performing throughout the fermentation process. This also makes for a great way to harvest yeast. Simply attach it to your dump valve and close off the other end with a T.C. end cap, collect the yeast and remove the sight glass, cap it at the other end and store it for your next batch. 1.5" tri-clamp Approximately 6.25" long Max Pressure: 120 PSI Max Temperature: 300°F Made from 316 stainless steel KegLand Part Number: KL01816
$43.99
-
Stainless Barb - 1/2 in. x 1/2 in. Female BSP
Stainless steel barb fitting. 1/2" female BSP x 13mm barb (0.51"). KegLand Part Number: KL03612
$6.59
-
KegLand Handy Clamp for BrewZilla | Tubing Clamp | 4" Long
Secure silicone hose to your mash tun during recirculation Large circular center of the clamp leaves room for tubing without pinching Excellent chemical resistance to common brewing cleaners and sanitizers Able to withstand boiling temperatures This handy spring clamp features a heavy-duty muslin spring which ensures your silicone hose never accidentally pops out of your mash tun and spills your precious nectar over your brewery floor. The large circular space between the arms of the clamp is perfect for passing 1/2" silicone tubing through without pinching. Rounded handles for a comfortable grip and a PE end grip to ensure your hosing is kept secure. Made from Polypropylene and Polyethylene which have good chemical resistance so it will stand up to the task for use around common brewing cleaners and sanitizers. Temperature Rating: 32-248°F KegLand Part Number: KL24686
$3.99
-
BrewZilla Ultimate Grain to Glass Combo Pack | Gen 4.1 BrewZilla All Grain Brewing System (110V) | WiFi/Bluetooth/RAPT Enabled | Neoprene Jacket & Hop Spider Included | FermZilla Tri-Conical Fermenter | Pressure Kit & Blowtie 2 Spunding Valve Included
The Ultimate Grain to Glass Combo Pack! Get the Gen 4 BrewZilla & FermZilla Easy-Grip Tri-Conical with all the best accessories at an unbeatable price! Brew extract or all grain batches on the BrewZilla; ferment, carbonate, and serve from the FermZilla. Everything you need from Grain to Glass! Comes with all of the most highly recommended accessories for the BrewZilla, including the Neoprene Jacket to speed up heating times, Hop Spider to keep vegetal matter out of your wort, and Chilling Connection kit so you're ready to use the Immersion Chiller out of the box Includes some of our favorite accessories for the FermZilla, such as the Pressure Kit with Floating Dip Tube so you're always racking the clearest beer and the Duotight BlowTie 2 for pressure fermentations and flow control keg transfers Over $100 savings when purchasing this kit bundle compared to buying everything piece-by-piece! Also available in 220V (AG582) You can search high and low, but you won't find a better deal than the BrewZilla Ultimate Grain to Glass Combo Pack! Combo Pack Includes: BrewZilla Brewing System | Gen 4.1 | 9.25G | 110V Neoprene Jacket Hop Spider Wort Chiller Connection Kit FermZilla Tri-Conical Fermenter | Gen 3.2 | 7.1G Plastic Pressure Kit w/ Floating Dip Tube Duotight BlowTie 2 Spunding Valve Insulating Jacket Gen 4 BrewZilla All-in-One Brewing System WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 110-120V power and plug 12.5A Requires 20A circuit Dual heating elements (1000 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 110–120V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use. 35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge FermZilla Tri-Conical Easy-Grip Fermenter A best seller for a reason! Tons of features at an incredible cost Crystal Clear super smooth PET makes fermenting and cleaning super easy 3" Butterfly valve at bottom makes removing yeast/trub easy with the 600mL collection jar. Pressurizable for fermentation and closed transfer to your keg Includes BlowTie spunding valve kit, red & yellow carbonation caps, and floating dip tube as standard The FermZilla is the perfect option for brewers that want all the advantages of a conical fermenter without the price tag of a full-blown stainless-steel unit. It allows you to dump trub, harvest yeast, and with the addition of CO2 cylinder and regulator, you can carbonate and serve – all in one vessel! The clear PET tank allows you to visually monitor fermentation activity and is pressure rated to 2.4 Bar (34.8 psi), which means you can ferment under pressure, reducing ester and fusel alcohols in your finished beer. This also gives the ability to perform pressure transfers. If you prefer to move your finished beer to a keg or other vessel, you can do so with little to no oxygen exposure. The FermZilla Tri-Conical Easy-Grip model comes packed with accessories so you can take full advantage of this pressurizable fermenter on day one. The new stock standard includes Easy-Grip threaded lid ring, BlowTie spunding valve with integrated pressure gauge, ball lock carbonation caps for the lid and collection container, floating dip tube kit with weighted filter, volume marker graduation sticker, and adhesive thermometer. What's Included: FermZilla 27L Tank with 3" T.C. Bottom Port Easy-Grip Threaded Lid Ring Integrated Gauge BlowTie Kit Spunding Valve (0-15 psi) Silicone Dip Tube Kit with Yellow Weighted Filter and SS Float (2) Yellow Liquid Carbonation Caps (2) Red Gas Carbonation Caps Fermzilla Pressure Lid with Red PRV (35 psi) 3" T.C. Butterfly Valve 600 mL Collection Container with 3" T.C. Connection Stainless Steel Stand with Swing Handles 3" tri-clamp with gasket Graduation Sticker Adhesive Thermometer Specs: 27 L (7.1 gal) Total Volume Pressure Rated to 2.4 Bar (34.8 psi) Height in Stand - 30.2" Tank Diameter - 13.9" Diameter in Stand - 15.3" Lid & Collection Container Ports - 28 mm PCO 1881 threads Temperature Rating: When not under pressure, do not expose to liquids above 131°F When under pressure, do not expose to any temperatures above 95°F* *Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years. Please note: when using the FermZilla under pressure, you must perform a water pressure check to ensure your connections are leak proof. To do this, fill your FermZilla up with water, apply at least 15 psi pressure, and check for leaks around all caps and threads. Pressure Stress If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple: Fill the tank to the brim with water Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher Pressurize the tank to 4 BAR (58 psi) Check for leaks, then replace the Red PRV when finished If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla. General Care Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank. KegLand Part number: KL47296 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary. FermZilla Tri-Conical 27L & 55L | User Guide
$829.99
-
Pro Sight Glass Distillation Lid | Steam Condenser Lid | BrewZilla | DigiBoil | 35L
Heavy-duty stainless steel lid can be used with a still top or steam condenser Sight glass disc allows you to watch your boil without having to remove your still or condenser Easily remove the disc during the hot break or to add hops or other boil additions Molded grips for easier handling with the lid is still hot Compatible with 35L BrewZillas and DigiBoils If you're using an AlcoEngine Still Top or Steam Condenser Set with your BrewZilla or DigiBoil, this heavy-duty stainless lid with sight glass is virtually a must-have. Whether distilling or brewing, keeping an eye on your boil will help you stop foaming or boil over issues before they happen. With the standard distillation lid, checking on your wash or wort means removing or tipping the apparatus over to get a peek inside the boiler, which can be a cumbersome (if not dangerous) part of your process. The PPSU sight glass disc can also be easily removed to add hops or other boil additions through the large 3" T.C. ferrule. (Use gloves, it will be hot!) The sight glass disc is made from a special PPSU plastic—an excellent choice for components that are exposed to high temperatures (up to 392°F / 200°C) and corrosive media due to its exceptional chemical resistance, as well as being extremely impact resistant. KegLand decided to use this type of plastic because it also has superior thermal and mechanical properties with the added benefit of being transparent. Intricate parts can be injection molded that would have been near impossible to do with stainless steel or lab-grade glass. For use with an AlcoEngine Still Top, you will also need this single sided bead seal. Installing AlcoEngine Still: Remove the bottom nut and seal from the column Place the single sided bead seal on the lid's tri-clamp ferrule (beaded side facing down) Pass the threaded bottom section of the column through the ferrule Secure in place with a 2" tri-clamp The column's bottom nut and seal are not needed Specs: 2" T.C. top ferrule port 3" T.C. sight glass ferrule Lid handles with molded grips Thicker silicone lid gasket for a tighter seal Includes: 3" PPSU sight glass disc 3" tri-clamp 3" silicone tri-clamp gasket Silicone lid gasket KegLand Part Number: KL25812
$164.99
-
EVABarrier Double Wall Draft Tubing - 6.3 mm ID x 9.5 mm OD
If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 6.3 mm (1/4") ID size is recommended to be used as gas line or long draw beverage lines. If you intend to use it as beverage line, we recommend using 20-25 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 6.3 mm (1/4") Outer Diameter - 9.5 mm (3/8") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. Kegland Part number: KL06248
$9.39 - $218.99
-
BrewZilla | Replacement Silicone Tubing Kit | Gen 4 | 35L
This is a complete replacement silicone tubing kit for the pump and ball valve tubing on a 35L Gen 4 BrewZilla. Made from food grade silicone and temperature resistant to 356°F (180°C). KegLand Part Number: KL27731
$10.99
-
NukaTap® Stainless Steel Beer Faucet | Forward Sealing
Newest faucet design on the market! Reduced first pour foam due to low thermal mass Forward-sealing design prevents beer residue from gumming up the faucet Unique shuttle design greatly improves laminar flow, improving the pour of carbonated beverages Compatible with all Intertap faucet accessories and shanks First Pour Foam Reduction Every kegerator owner knows the letdown of pouring your first pint of the day and getting too much foam. Even with perfectly balanced draft lines, first pour foam is sometimes unavoidable simply due to the temperature of the faucet itself. Running beer through the faucet will drop the temperature, and the foaming will subside, but not without a bit of wasted beer from pouring off excess head. The NukaTap beer faucet drops to beer serving temperature much faster thanks to its lower thermal mass. Simply put, the bulkier the faucet is, the more beer is needed to flow through and chill the tap. The NukaTap is over 20% lighter than its Intertap predecessor, and even lighter still compared to other brands of faucets. Improved Laminar Flow The inspiration for the NukaTap name comes from its uniquely designed "nuke-shaped" shuttle that resides on the inside of the faucet. The NukaShuttle went through numerous rounds of redesigns and countless hours of testing to find a shape that provides superior laminar flow. This means that liquid passes by the shuttle with very little resistance, allowing highly carbonated beers or hard seltzers to pour like a dream. Sanitary Design The NukaShuttle is the world’s first seamless single-piece design. Traditional taps feature an o-ring seated on a stainless steel shuttle, which can cause a couple of issues. After many pours, the stainless shuttle rubbing against the internal body of the faucet will create small fissures that become potential infection sites, and the seated o-ring can be difficult to clean in place, making your draft cleaning and sanitizing process less effective than you realize. The NukaShuttle is an advanced TPV rubber matrix that has been seamlessly formed over a durable PP skeleton. This single-piece design eliminates the pitfalls of older manufacturing methods, making it one of the most sanitary faucets on the market. Forward Sealing vs. Rear Sealing From tap rooms to home bars, forward-sealing faucets are the ideal choice for any draft setup. In traditional rear-sealing taps, beer will drain out of the entire faucet when it's in the closed position. This means the internal mechanism is coated in beer, which then dries and becomes a sticky residue. Forward-sealing faucets, on the other hand, keep the tap full of beer so it never has a chance to dry and gunk up the internal parts. This makes the faucet much easier to clean and also reduces the chance of off flavors transferring to your beer while you pour. Made from stainless steel Shuttle made from TPV O-rings made from EPDM NSF approved Kegland Part Number: KL15509
$39.99
-
High Temp Silicone Tubing | Reinforced | 1/2" ID
Reinforced silicone tubing offers higher temperature tolerances and chemical resistance while remaining flexible and easy to handle. Ideal for both cold side and hot side processes and high-pressure applications. Although braided, the tubing remains transparent to allow you to visually inspect the flow of liquids. 1/2" inner diameter 3/4" outer diameter Odorless, tasteless and inert Polyester heat resistant fiber reinforcing braid Good electrical and weatherability properties Resists UV, Ozone, gases, and moisture Working Temperature: -76°F–500°F Working Pressure: 0-150 psi KegLand Part Number: KL25300
$10.99 - $114.99
-
Duotight Push-In Fitting - 8 mm (5/16 in.) Elbow
This Duotight elbow fitting is compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL0240
$2.79
-
Stainless 3-Way Ball Valve - 1/2 in. BSP
Stainless steel 3 way ball valve with 1/2" female BSP at all ends. The T Port configuration has multiple open and closed positions. Please refer to see the function of each handle position. KegLand Part Number: KL15882
$30.99
-
Duotight Flow Control Ball Lock Quick Disconnect (QD) | Beverage Out | Adjustable Flow Rate | 8 mm Duotight
If you want an easy way to balance your beer lines, this is the way to do it. One of the benefits of Flow Control disconnects is you don't need to rely on the small ID or line length to apply flow resistance. Rather than adjusting your line length or size, simply apply additional restriction directly on the Quick Disconnect (QD). This is perfect for people who want to serve a large range of beverages with differing carbonation levels without having to customize each line. Now with the added benefit of Duotight fittings built in. Please be aware that even in the fully open position these FC disconnects do have some inherent flow resistance so you should use either shorter line or larger ID line that you would when compared with traditional ball lock disconnects. Flow Control QD vs. Flow Control Faucet One of the only drawbacks of flow control devices is that they inherently create a small amount of turbulence and therefore can cause foaming. In the past, flow control faucets have been the only common option. Flow control faucets are very popular but due to the fact that they are placed at the very end of the beer line they have no head pressure. As a result, any turbulence created can cause foaming and carbonation to come out of solution. Flow control ball lock disconnects like these on the other hand have the ability to restrict the flow before the beer enters the beer line so the head pressure created by the beer line keeps the carbonation in solution. Even in the instance that high turbulence is created the beer will be far more resistant to foaming issues. For this reason, flow control ball lock disconnects like these have significantly better performance allowing you the flexibility to adjust line resistance easily but without the introduction of turbulence that creates foaming. It cannot fix over-carbonated beer, but it can reduce the amount of beer line you would need to pour without excessive foaming. Duotight Ball Lock QDs The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required. Duotight Push-to-Connect These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done! Compact The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines. Overmolded Poppet The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out. Tool-less Disassembly Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects. Extreme Chemical Resistance No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing. Toughness This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough! Features: Ball Lock Quick Disconnect - Bev Out Adjustable flow rate Direct connect 8 mm EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Dissamble by hand for quick and easy cleaning KegLand Part Number: KL21418
$16.49
You have seen 144 out of 534 products