KegLand is a high quality homebrewing equipment brand based out of Australia. We offer a wide variety of their products, from BrewZilla all-in-one system and DigiBoil eletric kettles, to pumps and grain mills. KegLand beer products are an incredible value, as they combine quality craftsmanship with low prices!
Reduce heating time during your mash with the Gen 4 BrewZilla
Redistribute recirculating wort for longer heating element exposure
Improve heat distribution throughout the mash
Speed up heating times with the Heat Exchanger Dish (HED) for Gen 4 BrewZillas. This optional upgrade accessory redirects the flow of wort so that it spends more time exposed to the heating elements before reaching the center drain at the bottom of the kettle and being recirculated. Due to the concave bottom and central draining hole on the Gen 4 BrewZilla, recirculating wort will pass through the malt pipe and then down through the boiler false bottom following the path of least resistance. This can cause wort to make a B-line for the drainage hole and reduce the wort's exposure to the unit's heating elements. With the HED installed, wort will be directed to the edge of the BrewZilla base and pass over the elements for a longer period and reduce the time needed to heat to your set temperature.
For use with the Gen 4 35L BrewZilla. It is not compatible with any previous generations of BrewZillas or DigiBoils.
The HED has been pressed into a slight concave shape to match the curvature of the boiler false bottom. Includes a longer eye bolt assembly than the one included with the false bottom.
NOTE: The order of bolt to washer to nuts goes as follows. Eye bolt, washer, false bottom, washer, nut, HED, then wing nut. This is so that the eye bolt does not come completely removed when and if you clean underneath the Heat Exchanger Dish.
KegLand Part Number: KL29353
Upgrade your MKII pump with a 304 stainless steel replacement head. Stainless steel is more durable if you are attaching ball valves. Very occasionally the threads on the plastic head that comes standard on the MKII can break if you are using hard to close ball valves that apply a lot of torque. Stainless steel is very robust and will not break, is food grade, and well... stainless. Before you snag the stainless center-inlet head, also consider the stainless inline tri-clamp head. Kegland Part Number: KL03865
One of the great features of the KegLand pH Meter is the replaceable probe. The probes of pH meters wear out through normal use. Instead of making you buy a whole new pH meter you can just get the probe!
Kegland Part Number: KL04176
Completely impervious to oxygen and sunlight and made from 304 stainless steel, this growler is one of the best storage options for beer. This growler comes with a double wall vacuum insulation keeping your delicious beer cold for hours. The spring wired lid makes this growler capable of holding up to 30 psi. This is a smokin deal when compared to other double wall growlers. Dimensions: 4.75 in. Diameter x 12 in. Height; Holds 2L or 67 oz Draft Kit is out now! Kegland Part number: KL04282
Swap out the standard BrewZilla recirculation arm with this flexible upgrade Perfectly position your recirculating wort or sparge water over the grain bed Use the BrewZilla's built-in pump to easily transfer wort to fermenter or clean the kettle with a CIP head This simple upgrade for the BrewZilla is perfect for positioning your recirculating wort or sparge water over the grain bed and makes it even easier to use the unit's built-in pump for transferring wort to your fermenter or for CIP at the end of the brew day. Pairs perfectly with the Sergeant Sparge Head for mashing and sparging, as well as the BrewZilla Spinning Spray Rotor to clean your kettle. Please note: Camlocks sold separately. You will need a Male Camlock x 1/2" Male Thread adapter in order to attach the Flexi Arm to your BrewZilla recirculation piping. Specifications: 304 Stainless Steel Fitted Female 1/2" Hex Nut Ends Silicone Washers Included Length 31.5" KegLand Part Number: KL15097
Perfect for spraying down brewing equipment with dissolved cleaners or sanitizers Attach the optional Ball Lock Keg Post Adapter to convert the sprayer into a line cleaning device Empty the large 33.8 oz tank up to 30 times on a single charge The Power Sprayer is a fantastic multi-purpose device that can be used for spraying down your brewing equipment with cleaners and sanitizers or converted into a pressurized line cleaning system. The tank features graduated volume markers and can be emptied up to 30 times on a single charge. The nozzle knob can be adjusted to turn the stream into a fine mist or a powerful jet. This product is made from food grade Santoprene, PP, PE, Silicone and stainless components. Battery Life The pump has large 18650 li-ion rechargeable battery. On a full charge the battery will empty the tank 18-30 times so it lasts for ages. If you use fine mist it will be closer to 18 times but if you use a jet/stream the battery will last closer to 30 times. Includes: 33.8 oz Reservoir Tank Power Sprayer Nozzle and Dip Tube White Plastic Adjustment Head Sprayer 6" USB-C to Standard USB Cable *Does not include USB wall charger
KegLand Part Number: KL40860
Take the guesswork out of oxygenation with this handy flow meter. If you're using pure O2 to oxygenate your wort, you're likely using a disposable cylinder with a simple brass regulator, and have no way to measure how much oxygen is actually being added. You're essentially left to finding the "sweet spot" on the dial when you open the regulator and aim for the same spot on the next use. Get repeatable results by adding this flow meter to your setup. This device will allow you to dial in the flow rate and help you add the same amount of oxygen from batch to batch.
The flow meter comes with male flare thread inlet and outlet and includes two Duotight fittings. It's ready for use with 8 mm OD EVABarrier tubing right out of the box, or you can add a swivel nut and barb for use with other size tubings.
Once yeast pitching temperatures are reached, we recommend using a 0.5 micron diffusion stone and adding pure O2 at a 1L/minute flow rate for 60 seconds to acheive the recommened 10-14 ppm dissolved oxygen.
Features:
1/4" Male Flare Inlet/Outlet
Duotight Fittings for 8 mm OD Tubing Included
Scaled for 0.1 to 1.5 L/min Flow Rate
3.6" H x 0.9" W
Kegland Part number: KL13185
Track your mash tun run off during sparging, pre-boil gravity, post-boil gravity, and starting gravity before fermentation
Readings are almost instantaneous, requires only a few drops, and there's no need to cool your sample thanks to ATC
Triple scaled for use in brewing, winemaking, and distilling
LED illumination makes it easy to see your readings even in low light environments like your garage or basement
Water resistant enclosure—dip the refractometer into your wort without risk of damaging the LED light
Includes case, pipette, and USB magnetic charging cable
If you want a quick and easy way to take gravity readings during the brewing process, then a refractometer is the tool for the job. Taking hydrometer readings during the brew tends to be a time-consuming process, and by the time you get a reading it may be too late to react. This is because you need to take a large sample and cool it to get an accurate reading. A refractometer allows you take instant gravity readings, with just one drop, at any point during the boil, or even during the run off of the sparge during an all-grain brew. These 'during the process' readings allow you to add more water or boil longer so you can attain exactly the gravity you desire.
Traditional refractometers without ATC are calibrated to work at 68°F. The ATC function allows you to use the refractometer in an ambient temperature range of 50-86°F (10-30°C). Since your sample is just one drop, and will quickly adjust to the temperature of the refractometer, the temperature of the sample is irrelevant. This unit also comes with a manual calibration knob that is secured with a lock nut. To calibrate place one drop of distilled water on the testing platform and adjust to zero if necessary. The LED light is a handy feature that helps illuminate the sample and make the scale easier to read.
Features:
Triple Scaled
0-32 Brix
0-1.130 Specific Gravity for Wort
0-1.130 Specific Gravity for Sugar
Water resistant enclosure
Adjustable focus eyepiece with rubber grip
Automatic Temperature Compensation
LED illumination function
Rechargeable battery
Please Note: The Sabre Refractometer is used to measure unfermented wort. Once alcohol is present, the use of a correction table is advised.
KegLand Part Number: KL25072
This mini pressure gauge is compatible with the BlowTie 2 spunding valve, Duotight in-line regulator, and KegLand mini regulator. We recommend using the gauge with a range closest to your desired pressure setting. If you'd prefer a digital instant read gauge, check out the Digital Mini Pressure Gauge (for gas applications only). Pressure Range: 0-30 psi (0-2 bar) Body Dimensions: 26mm x 26mm x 15mm Probe Diameter: 8mm WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Kegland Part number: KL14991
This Duotight to 1/2" female thread fitting can be used to connect beverage or gas line to fittings with 1/2" male threading. Compatible with EVABarrier 9.5 mm OD Tubing (D1719).
Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines!
Features:
Insert tubing and firmly push to connect
Easily release tubing by pushing in the collet
Suitable for both gas & beverage applications
Made from food-grade acetal plastic
Double O-rings made from highly chemical resistant EPDM
Locking teeth made from stainless steel
Pressure rated to 150 psi
Temperature rated to 212°F (100°C)
Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals.
Kegland Part number: KL13871
The lowest price Pressurizable fermentor out there.
Perfect for most ales that ferment in 2 weeks or less
Super smooth PET makes cleaning very easy
Transfer to your keg closed and under pressure oxygen free
PET is better oxygen barrier than fermentors made of HDPE
Super lightweight yet strong and shatterproof
The FermZilla All Rounder is the most affordable pressurizable fermenter on the market. Although it doesn't feature a dump valve like the FermZilla Conical, the All Rounder carries the same pressure rating, making it an absolute steal if you're looking to ferment under pressure, perform pressure transfers, or want to carbonate and serve directly from the fermenter. The All Rounder is made from super smooth PET that's easy to clean, and the simple design means no nooks or crannies for microbes to hide. With a 4.75" lid opening, you'll have no trouble getting your arm inside to scrub away stubborn krausen rings. As with all FermZilla fermenters, the lid features molded drill locations that make installing accessories like a thermowell or Temp Twister Cooling Coil a breeze.
In order to unlock the full potential of the All Rounder, you'll want to pick up the 55L FermZilla Pressure Kit. The pressure kit is available with either stainless or plastic ball lock caps.
Why MoreBeer! loves the All Rounder FermZilla:
Super smooth PET makes cleaning very easy.
Pressure rated lid and PET material make for a better oxygen barrier than fermenters made of HDPE.
Lightweight and easy to move around, yet strong enough to be considered shatterproof.
The 4.75" lid opening makes it easy to get your arm inside and clean after use.
The lid is designed for the easy installation of accessories such as a thermowell or cooling coil.
Price! A pressurizable fermenter in this price range is an incredible value, and it opens the door for many cold-side processes that can't be done in a normal carboy or plastic fermenter.
What's Included:
FermZilla 60L All Rounder Fermenter
Stainless Steel Stand
Stainless Steel Handle
Top Lid with PRV (35 psi)
3-Piece Airlock
Adhesive Thermometer
Specs:
60 L (15.9 gal) Total Volume
Pressure Rated to 2.5 Bar (36.2 psi)
Height in Stand - 34"
Height w/ Airlock - 36.5"
Tank Diameter - 13.9"
Lid Ports - 28 mm PCO 1881 threads
Temperature Rating:
When not under pressure, do not expose to liquids above 131°F
When under pressure, do not expose to any temperatures above 95°F*
*Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years.
Kegland Part number: KL15196
NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.
FermZilla All Rounder 30L & 60L | User Guide
A perfect pocket temperature probe for homebrewing and BBQ! Check the temperature of your mash, whirlpool additions, or see if that mouthwatering tri-tip is ready to be pulled off the grill. With a range of -58°F to 572°F there's basically no way you won't get a temperature reading unless you live in an active volcano (do not recommend).
Specifications:
Range: -58°F – 572°F (-50°C – 300°C)
Resolution: 0.1°C
Temperature Error: +-1°C (0~100°C)
Power Supply: 1 x AG13 Battery (included)
Functions:
On/Off
°C/°F
Hold
KegLand Part Number: KL23320
The Ultimate FermZilla Combo Pack! Get the FermZilla Easy-Grip Tri-Conical & our most highly recommended accessories at an unbeatable price!
Includes some of our favorite accessories for the FermZilla, such as the Pressure Kit with Floating Dip Tube so you're always racking the clearest beer, Duotight BlowTie 2 for pressure fermentations and flow control keg transfers, and Insulating Jacket to help maintain stable fermentation temps
These accessories will help unlock the FermZilla's full potential, so buy them together and enjoy the savings!
Combo Pack Includes:
FermZilla Tri-Conical Easy-Grip Fermenter | 27L | 7.1G
Pressure Kit w/ Floating Dip Tube
Duotight BlowTie 2 Spunding Valve
Insulating Jacket
FermZilla Tri-Conical Easy-Grip Fermenter
The FermZilla is the perfect option for brewers that want all the advantages of a conical fermenter without the price tag of a full-blown stainless-steel unit. It allows you to dump trub, harvest yeast, and with the addition of CO2 cylinder and regulator, you can carbonate and serve – all in one vessel! The clear PET tank allows you to visually monitor fermentation activity and is pressure rated to 2.4 Bar (34.8 psi), which means you can ferment under pressure, reducing ester and fusel alcohols in your finished beer. This also gives the ability to perform pressure transfers. If you prefer to move your finished beer to a keg or other vessel, you can do so with little to no oxygen exposure.
The FermZilla Tri-Conical Easy-Grip model comes packed with accessories so you can take full advantage of this pressurizable fermenter on day one. The new stock standard includes Easy-Grip threaded lid ring, BlowTie spunding valve with integrated pressure gauge, ball lock carbonation caps for the lid and collection container, floating dip tube kit with weighted filter, volume marker graduation sticker, and adhesive thermometer.
What's Included:
FermZilla 27L Tank with 3" T.C. Bottom Port
Easy-Grip Threaded Lid Ring
Integrated Gauge BlowTie Kit Spunding Valve (0-15 psi)
Silicone Dip Tube Kit with Yellow Weighted Filter and SS Float
(2) Yellow Liquid Carbonation Caps
(2) Red Gas Carbonation Caps
Fermzilla Pressure Lid with Red PRV (35 psi)
3" T.C. Butterfly Valve
600 mL Collection Container with 3" T.C. Connection
Stainless Steel Stand with Swing Handles
3" tri-clamp with gasket
Graduation Sticker
Adhesive Thermometer
Specs:
27 L (7.1 gal) Total Volume
Pressure Rated to 2.4 Bar (34.8 psi)
Height in Stand - 30.2"
Tank Diameter - 13.9"
Diameter in Stand - 15.3"
Lid & Collection Container Ports - 28 mm PCO 1881 threads
Temperature Rating:
When not under pressure, do not expose to liquids above 131°F
When under pressure, do not expose to any temperatures above 95°F*
*Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years.
Please note: when using the FermZilla under pressure, you must perform a water pressure check to ensure your connections are leak proof. To do this, fill your FermZilla up with water, apply at least 15 psi pressure, and check for leaks around all caps and threads.
Pressure Stress
If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple:
Fill the tank to the brim with water
Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher
Pressurize the tank to 4 BAR (58 psi)
Check for leaks, then replace the Red PRV when finished
If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla.
General Care
Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank.
KegLand Part number: KL47296
NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.
FermZilla Tri-Conical 27L & 55L | User Guide
If you've been looking to step up from fermenting in plastic buckets or carboys, this is an excellent choice for your next fermenter. Stainless steel is a much better option than glass or plastic, as it is extremely easy to clean and virtually lasts forever. There's also much less chance of contamination as stainless doesn't scratch like plastic. Over time, you'll get scratches in plastic fermenters from normal wear and tear, creating microscopic havens for bacteria. Meanwhile, glass carboys are always at risk of breaking which is something you will never have to worry about with stainless steel. The Bucket Buddy is a great value if you're looking for a stainless steel fermenter with built-in heating control. If you live in a cold climate, ale fermentations may be a seasonal affair, as cold ambient temperatures can easily drive down the temperature of your wort below your yeast's optimal fermentation temp range. The Bucket Buddy offers a simple solution with an integrated heating element and digital temperature control. Program your fermentation temperature and if the temp drops below your set point the unit will gently heat your wort from the bottom up via the concealed element located in the base. For cooling, you can place the fermenter in a dedicated refrigerator or drill into the lid to install a Temp Twister Cooling Coil. A temperature controller probe can then be taped to the side of the fermenter to control your cooling source, or you can drill another spot in the lid for a thermowell. Another advantage over carboys and plastic buckets is the domed base inside the fermenter which is great for yeast flocculation when fermentation is complete. The included racking arm will make it easy to transfer out every last drop of beer while leaving the yeast cake undisturbed. The entire racking arm and ball valve assembly is weldless, which means you can remove the assembly to clean and sanitize it between batches. You can even boil the assembly for added assurance that it's been sterilized. To help maintain a steady temperature and cut down on power consumption, the Bucket Buddy pairs well with either the BrewZilla Neoprene Jacket or the FermZilla Insulating Jacket. This unit comes standard with silicone tubing to transfer from the ball valve to your bottles or cans, as well as a stopper and airlock for the domed lid. Specifications: 304 stainless steel construction 9.25 gallon total capacity Digital temperature control 110V / 36W power Stainless steel outlet valve with rotating racking arm Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C External Dimensions: 28" H x 15" W (including handles) Internal Dimensions: 22" H x 11.75" W Please note: Heating capacity is highly dependent on ambient temperature and use of insulation. Testing has shown that the Bucket Buddy can heat to 104°F in a room temperature ambient environment without insulation. Adding insulation may increase heating capacity while colder ambient environments may lower heating capacity. KegLand Part Number: KL20695
No more spillovers! Set your desired volume and walk away
Automatically collect water while you tend to other tasks
Great for collecting brewing water or mixing your cleaning and sanitizing chemicals
Illuminated display in splash resistant housing
Integrated solenoid valve cuts off flow when your set volume is dispensed
1/2" BSP inlet and outlet work well with Duotight or Type A Camlock fittings
Unlike other hose timers that simply measure time, the Fill-O-Meter measures volume and will automatically turn off when the programmed volume of water is dispensed. Enter your desired volume of water, press Start, and tend to other brew day prep work. Install in-line with your water filter to automatically collect filtered strike water, or measure out how much water you need to mix with cleaning chemicals for a precise dilution ratio.
We recommend setting up the Fill-O-Meter with either Duotight fittings or Type A Camlocks. Thread tape will be required for the Camlock. Use sparingly as too much plumber's tape can damage the plastic thread. And it is very important to never overtighten!
Displays real time flow rate and volume (Liters/Min or Gallons/Min)
Accurately measures and controls volumes at flow rates from 1-30L/Min (0.26-7.9Gal/Min)
Never overfill or spillover again
Splash resistant housing
Great for filling tanks, brewing kettles, distilling gear, mixing liquid and many other applications
Integrated flow meter and solenoid valve
Illuminated display for usage in the evening
Integrated sound alarm
Easy 1/2" BSP Inlet and Outlet
Automatic failsafe - flow is stopped if the unit loses power
Important Notes:
DO NOT flow liquid the wrong direction, it will break the unit.
DO NOT overtighten fittings onto the 1/2" ports.
DO NOT exceed temperatures greater than 104°F (40°C) through the unit.
Specifications:
Flow Range: 1-30L per minute
Temperature Range: 32-104°F (0-40°C)
LCD: 3 inch back lit display
Housing Material: ABS
Input/Output threads: BSP 1/2"
Pressure Rating: 0-12bar (0-180psi)
Accuracy: +/- 5%
Please Note: Accuracy can be improved with stable flow. Repeated start/stop or variation in water supply can have negative effect on accuracy. If you are noticing innaccurate fill levels, see the instruction manual for calibration instructions.
KegLand Part Number: KL14694
Converts the KegLand Power Sprayer into a compact, convenient line cleaning device
Ball Lock multi-post is compatible with both Gas & Liquid QDs
Attach the Ball lock Keg Post Adapter to the KegLand Power Sprayer to turn the unit into a convenient line cleaning device. The multi-post is compatible with both Gas & Liquid ball lock quick disconnects.
This part is only suitable for the Power Sprayer. It is not a standard thread size. It has been custom made for this product and this product only.
Please Note: The keg post adapter does not include a spring & poppet. This is intentional in order to prevent the flow path from being blocked if the sprayer was unintentionally powered on without a ball lock disconnect connected to the post. Powering the sprayer with the flow path blocked could damage the pump.
KegLand Part Number: KL42871
Adjustable relief valve installs on standard ball lock keg posts Use with any ball lock keg to control flow during closed pressure transfers Integrated pressure gauge can be swapped out with a digital gauge or large face dial gauge for easier, more accurate readings Adjustable black cap can be swapped out for color coded PRVs with a fixed pressure Low-profile design only measures 1.75" in height This easy to use and compact pressure relief valve is super handy for keg transfers. Using a ball lock quick disconnect as the main body, the valve easily snaps onto ball lock keg posts. Adjustable relief valves are a great way to limit oxygen exposure and regulate flow during closed keg transfers, The included gauge reads from 0-30 PSI and can be swapped out with a digital gauge or large face dial gauge for easier, more accurate readings. The black pull ring cap on the other end can be rotated for adjustments, or swapped to a range of color coded PRVs for a fixed pressure. This low-profile option only measures 1.75" in height. It works right out of the box but has several upgrade options as shown in the images. Warning: Never swap out the valve's standard PRV with a color coded PRV that exceeds the pressure rating of your vessel. Features: Duotight fitting where the gauge attaches This allows for upgrading the valve with a digital gauge or larger analog gauge Manual pull ring pressure relief This allows for you to not only adjust the pressure with the black rotary knob but also use the ring pull to instantly release pressure if you want to release manually Option for several color coded PRVs to be used (see below) Yellow - 17 psi Red - 35 psi Green - 65 psi Gray - 100 psi KegLand Part Number: KL29438
Upgrade your FermZilla Conical or All Rounder with the new 2" Tri-Clamp Lid from KegLand. Add yeast, hops or even take samples from a wine thief from the top and not have to remove the entire lid. This particular lid was designed in order to suit a growing number of customers desire to dry hop without exposing the batch to oxygen from opening the lid. By using this lid in conjunction with the FermZilla 2" Butterfly Valve and Hop Bong Kit, you will be able to purge CO2 into the tube and expel all the oxygen inside it and dump freely into the vessel. Features: (2) PCO1881 Male Ports Recommended for use with Red (Gas In) & Yellow (Bev Out) Ball Lock Caps PRV Port with Red 35 psi (2.5 BAR) PRV 2" T.C. Ferrule Undrilled Ports (for optional accessories): Thermowell Port (see below for FermZilla Thermowell kit) (2) Temp Twister Ports Please Note: Temp Twister will need to be bent on a 20° Angle in order to fit on the curved lid and align vertically in the tank. Also includes: 2" Tri-Clamp 2" T.C. Gasket 2" T.C. x PCO1881 Male Thread Cap If you ever need to replace the O-ring attached to the bottom of the Pressure Lid, a Corny Keg Lid O-ring fits perfectly. KegLand Part Number: KL28219 Warning: Always depressurize your system COMPLETELY before removing fittings from your fermenter. Warning: Only use Red 35 psi PRV with this lid. Ensure the PRV is cleaned and dried of sticky residue before each fermentation. Failure to do so could cause injury and void warranty.
This Duotight reducer fitting can be attached to the Intertap Short Shank with 1/4" Duotight compatible barb (D1242). Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Also attaches to the Plastic Ball Lock Cap, allowing the cap to be used with 8 mm OD EVABarrier. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07481
A distiller's parrot is a piece of equipment that allows you to take alcohol gravity measurements using an Alcometer continuously throughout your pot or reflux run. It should be placed inline of your distillation outlet so that the drops of distillate fall directly into the tallest collection cone. But it should only placed in-line after you collect your foreshots. Your alcometer is then gently placed into the lower cone. Be careful not to drop in the alcometer before there is any liquid/distillate in the cone, as dropping it into an empty cone could break your glass alcohol meter.
Specifications:
Max Capacity: 105 ml (w/o alcometer)
Weight: 1.9 lbs
Made from 304 Stainless Steel
Kegland Part number: KL14823
I.D. of 19mm (0.74")
Does not include alcohol meter.
A magnetic stir plate is a great investment to help improve the quality of your yeast starters. Aeration is an important factor in making a yeast starter, and without a stir plate you'll need to pick up and swirl your starter by hand as often as possible. The stir plate is a simple solution that will continuously aerate your starter, leading to higher numbers of viable yeast.
This compact stir plate works with Erlenmeyer flasks up to 5000mL in size. Depending on the volume of your yeast starter, you can use the adjustment knob to dial in the speed of the stir bar. We recommend using just enough power to keep yeast in suspension, a full vortex isn't really necessary.
Stir bar included.
KegLand Part Number: KL05555
Scrub your beer bottles clean with this bottle-shaped brush. Soak bottles in your preferred cleaning solution, scrub the inside with the bottle washing brush, and rinse.
17.5" long. Bristle section is 12" long.
Kegland Part number: KL12997
If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 5 mm (13/64") ID size is perfect for draft applications where a longer beverage line is needed. We recommend using 10-12 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 5 mm (13/64") Outer Diameter - 8 mm (5/16") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. Kegland Part number: KL06231
Ever wanted to punch out a few more gallons of wort with your 35L BrewZilla? Maybe you wanted more strike water for a super sticky batch. Maybe you get boil overs a lot and would like a bit of extra protection. Now there's a solution! The all new 35L BrewZilla Boiler Extension adds 3.1 gallons of headroom. Turn that 9.2G BrewZilla or DigiMash system into a 12.3G behemoth! The extension kit is also great for distilling! Extend the height of your pot still by attaching one or more boiler extensions. For distillation, we recommend upgrading to the Adjustable Lid Clamps which allow you to dial in the tension for a better seal. If you're struggling to get an airtight seal when using the Distillation Lid, these clamps can help provide more tension. Compatible with Gen 3 / Gen 4 BrewZillas. Please Note: The 110V unit may struggle to bring 10+ gallons of wort to boil. Expect longer heating times and a more gentle boil. An insulating jacket is highly recommended if using the 110V model. You Might Also Need: 35L Extended Malt Pipe 35L Wire Support Ring Recirculation Arm Extension KegLand Part Number: KL22231
Get instant pressure reads with the back illuminated Digital Mini Pressure Gauge from KegLand. Compatible with 8 mm Duotight fittings and Gray Ball Lock QDs. If you're using the original BlowTie spunding valve without pressure gauge, you can use a Duotight tee fitting in-line between the ball lock QD and the BlowTie to take pressure readings with the Digital Mini Gauge. KegLand has developed the world's most compact mini digital gauge with backlight illumination. This very compact design retains high accuracy while still meeting the desirable small form factor. This meets the growing need as mini keg systems, mini regulators and other more compact keg dispensing solutions are required. Traditional analogue gauges require a small capillary mechanism where a small pipe expands and unravels under pressure. This in turn drives a mechanical cog to rotate the gauge needle. This age-old technique works quite well especially in large gauges but as this mechanism is manufactured smaller and smaller a tradeoff between accuracy and size becomes the issue. With very small gauges such as a 27mm x 27mm Mini Gauge, it's difficult to make them better than 10% accuracy due to the physical constraints of the mechanical components. Specifications: Battery Life: More than 2 years (using the mini gauge once a day) Battery Type: CR2032 Auto Battery Saver: automatically turns off after 15 sec Size: 27mm x 27mm (1" x 1") Duotight Stem: 8 mm KegLand Part Number: KL18081 Please note: This gauge is not suitable for measuring pressure of liquids. It is only for measuring gas pressure. If liquid gets into the pressure transducer it will damage the gauge.
Add this neoprene jacket to your Gen 4 BrewZilla to speed up heating!
Heating is 10% faster and heat loss from the boiler is reduced by 50%
Remove the jacket after the boil to speed up chilling
Thick, insulating neoprene is secured to the boiler body with a sewn-on hook and loop fastener strap
Sparge arm sleeve included to reduce heat loss during mash recirculation
Add some insulation to your BrewZilla to get better boils! This neoprene jacket will help keep the heat in for quicker and more vigorous boils. Slap it on to speed up heating; take it off to speed up chilling. Also includes a neoprene sleeve for the recirculation arm to reduce heat loss during the mash.
This jacket will fit Gen 4 BrewZilla models. It is not compatible with older generations of BrewZillas and DigiBoils due to where the cutouts on the jacket are located.
Features:
10% faster heat up time
50% less heat loss from boiler
Fits the 65L BrewZilla Gen 4
Made from 8 mm thick neoprene which is easy to wash after use
KegLand Part Number: KL24372
Want an easy-to-use, stainless vessel that ferments and carbonates? This 29L/7.6 Gallon keg has been modified to allow you to do both! The top is fitted with a large 4 inch tri-clamp lid with two ball lock posts and a pressure relief valve. You can use this vessel to ferment, carbonate, serve, or push the beer through a filter. The posts are recessed which allows you to stack these kegs up to 4 high. A 4" T.C. end cap with pre drilled hole is also available (H691), which can be paired with a #3 stopper and airlock. Also consider the Kegmenter Hop Bong Pressure Pack which allows for oxygen-free dry hopping and also features ball lock posts for Gas & Liquid. Depending on how long it will take to consume the finished beer, we recommend using two kegmenters, one for fermentation and one for carbonating and serving. After fermentation, there will be a large trub cake at the bottom of the vessel. Leaving finished beer on the trub for too long (2-3 weeks) may eventually lead to off-flavors. Check out our ball lock jumper line (KEG575) to easily transfer from one kegmenter to the other. Also consider our beer filter kit (FIL40), which will allow you to filter the beer during transfer. Features: Rated up to 2.5 BAR (36 psi) 4" T.C. lid with ball lock posts Floating dip tube Stainless steel 1.8 mm thick Use: As a stainless steel fermenter that is easy to clean Great choice for 5 gallon fermentations Easy to pressurize the kegmenter after fermentation to push through a filter and into another keg Fermenting under pressure, allowing CO2 to exit via the relief valve, reduces esters and fusel alcohol production allowing you to ferment at warmer temperatures Distillation - with the addition of a T.C. reducer and condenser (H701 / DS120 / DS130) As a cellar keg for topping up barrels Warning: Always depressurize keg before removing lid. Does not include spunding valve shown in example photo. Please see FIL42A. Kegland Part number: KL05906
Use this insulating jacket to regulate the fermentation temperature in your 30L FermZilla All Rounder. The jacket alone will help keep your fermenter warm in the colder months, or you can add a FermWrap heater if the heat fermentation isn't enough to maintain temp. Conversely, you can freeze bottles of water and put them inside the jacket to keep the temperature from getting too hot. If you're feeling extra fancy, use frozen water bottles and a FermWrap plugged into a temperature controller. The frozen water bottles will provide constant cooling, and if the controller detects that the temperature has dropped too far, it will kick on the FermWrap to heat your fermenter back up to your target temp. The jacket has the added benefit of protecting your fermenting beer from harmful UV light. Features a single sided zipper and draw string bottom. Kegland Part number: KL19590
The ultimate plastic pressurized conical
A best seller for a reason! Tons of features at an incredible price
Cyrstal clear super smooth PET makes fermenting and cleaning super easy
3" Butterfly valve at bottom makes removing yeast / trub easy with the 600mL collection jar
Pressurizable (with accessories) for fermentation and closed transfer to your keg
The Gen 3.2 FermZilla Tri-Conical features a newly designed collection container with top & bottom PCO1881 ports. The collection container has a 3" T.C. opening and installs on the Conical with a 3" T.C. butterfly valve. The molded 3" T.C. ferrule on the tank is a huge improvement over the Gen 2 model—eliminating the complicated dump valve design and simplifying the collection container connection. Brew with confidence on the new Tri-Clover FermZilla!
NOTE: The primary example photo shows the collection container from the Gen 3 FermZilla.
Out of the box, the FermZilla Conical is an amazing fermenter that will immediately step up your game on the cold side of the brewing process. But what we love most about this unit is how easily it is to upgrade as you go—adding more functionality and gaining more precise control over your fermentation with each new accessory. Below are some of our favorite add-ons for the FermZilla Tri-Conical Fermenter.
Pressure Kit
The FermZilla is the perfect option for brewers that want all the advantages of a conical fermenter without the price tag of a full blown stainless steel unit. It allows you to dump trub, harvest yeast, and with the addition of the FermZilla Pressure Kit, you can carbonate and serve – all in one vessel! The clear PET tank allows you to visually monitor fermentation activity and is pressure rated to 2.4 Bar (34.8 psi), which means you can ferment under pressure, reducing ester and fusel alcohols in your finished beer. This also gives the ability to perform pressure transfers. If you prefer to move your finished beer to a keg or other vessel, you can do so with little to no oxygen exposure.
Tri-Clamp Pressure Lid
Add a 2" T.C. port to your fermenter by replacing the standard lid with the FermZilla Tri-Clamp Pressure Lid. This will give you an opening to add dry hops or other additions without needing to remove the entire lid, or you can upgrade down the road with a Hop Bong sight glass in order to add CO2 and purge your hop charge of oxygen. PCO1881 threaded ports are still there for Ball Lock Caps, as well as undrilled ports for an optional Thermowell and Temp Twister cooling coil.
Hop Bong Pressure Pack
The ultimate upgrade kit! The Hop Bong Pressure Pack has all of the parts included with the Pressure Kit and Tri-Clamp Pressure Lid but fully parted out to remove the guess work. If the Tri-Conical is your first FermZilla fermenter, this accessory kit is for you. Load up the Hop Bong, flush it with CO2, purge out oxygen with the handy PRV on top, then simply open the Butterfly Valve to inject your beer with a 6 oz payload of dry hops.
FermZilla Gen 3 vs Gen 3.2:
3" x 3" T.C. butterfly dump valve
3" T.C. compatible collection container
600 mL collection container w/ top & bottom PCO1881 threaded ports
What's Included:
FermZilla 55L Tank with 3" T.C. Bottom Port
3" T.C. Butterfly Valve
600 mL Collection Container with 3" T.C. Connection
Stainless Steel Stand with Swing Handles
Stainless Steel Handle Assembly
Top Lid with PRV (35 psi)
3" tri-clamp with gaskets
3-Piece Airlock
Graduation Sticker
Adhesive Thermometer
Spare Seals
Specs:
55 L (13.2 gal) Total Volume
Pressure Rated to 2.4 Bar (34.8 psi)
Height in Stand - 41.5"
Height w/ Airlock - 45.1"
Tank Diameter - 13.9"
Diameter in Stand - 15.3"
Lid & Collection Container Ports - 28 mm PCO 1881 threads
Temperature Rating:
When not under pressure, do not expose to liquids above 131°F
When under pressure, do not expose to any temperatures above 95°F*
*Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years.
Please note: when using the FermZilla under pressure, you must perform a water pressure check to ensure your connections are leak proof. To do this, fill your FermZilla up with water, apply at least 15 psi pressure, and check for leaks around all caps and threads.
Pressure Stress
If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple:
Fill the tank to the brim with water
Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher
Pressurize the tank to 4 BAR (58 psi)
Check for leaks, then replace the Red PRV when finished
If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla.
General Care
Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank.
KegLand Part number: KL25904
NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.
FermZilla Tri-Conical 27L & 55L | User Guide
Leak-Proof Double O-Ring Technology: Engineered with high-quality EPDM double O-rings, providing twice the sealing surface of standard push-in fittings for maximum reliability and a leak-free draft setup.
Modular & Customizable Gas Control: Features integrated, removable check valves to prevent backflow and a tool-free "pop-tab" design that allows you to easily swap, remove, or plug individual ball valves.
Instant Tool-Free Connectivity: Designed for 8mm EVABarrier tubing, the Duotight push-to-connect system allows for secure, seconds-fast installation with flexible mounting options for any kegerator or fermentation chamber.
Please Note: The Duotight Manifolds feature 8mm Duotight connections at both ends. One end is intended for your gas line and the other can be used to attach another manifold or a variety of accessories. If you will not be installing anything on the other end, you will need a 8mm Plug to cap the opposite end from your Gas In (see below).
Streamline your draft setup with the Duotight Gas Manifold, featuring integrated check valves on every ball valve outlet. These check valves provide essential protection by preventing backflow; however, they can be easily removed if you require gas to flow freely in both directions. 8mm Duotight push-to-connect inlet and outlets allow you to easily connect EVABarrier draft tubing in seconds. Available in 2-Way, 4-Way, and 6-Way configurations.
Customization & Modular Design
This manifold is designed for flexibility. If you need to shut off specific lines permanently, we recommend using the Duotight 8mm Plug (DUO102). Modifying the unit is straightforward: use a thin flat-head screwdriver to pop the black retainer tabs, allowing you to remove or swap individual ball valves as needed. If you wish to expand your manifold the future, multiple Duotight Manifolds can be connected using the 8mm Rigid Joiners (DUO202).
Mounting Solutions
Every manifold comes ready for installation with button-head screws for standard mounting. If you prefer not to drill into your kegerator or fermentation chamber, we suggest using Duotight Adhesive Brackets (DUO263) for a secure, tool-free setup.
High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage.
The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market.
EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free.
No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
KegLand Part Numbers:
KL46220
KL46237
KL46244
Duotight Manifold | User Guide
This Duotight to Female Beer Thread (5/8" BSP) fitting can be used to connect beverage line to faucet shanks instead of a tailpiece, and it's also a convenient option for connecting gas and beverage line to the gas in and bev out on keg couplers. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Faucet shank and keg coupler not included. Kegland Part number: KL06903
For those that want absolute precision when setting their mill gap, a feeler gauge is a must. Made from carbon steel with 17 blades of various thickness from 0.02 mm to 1.00 mm. Each blade is clearly marked with its thickness. The tool itself measures approximately 107 mm x 13 mm x 8 mm (4.2" x 0.5" x 0.3").
17 Blades:
0.02mm
0.03mm
0.04mm
0.05mm
0.06mm
0.07mm
0.08mm
0.09mm
0.10mm
0.15mm
0.20mm
0.25mm
0.30mm
0.40mm
0.50mm
0.75mm
1.00mm
KegLand Part Number: KL13420
This Duotight check valve is a great idea for protecting your regulator or add it in line with your mains water pressure when using the KegLand Continuous Soda Carbonator Keg Lid. It has a low opening pressure of 1 psi. This check valve is suitable for clean liquids such as water or for gas. Since it cannot be disassembled for cleaning, we do not recommend it for beverage applications. The internal components are made from stainless steel. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & water applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07047Kegland Part number: KL07047
Automated Filling System: Fill any beverage into any bottle, can, jar, or glass automatically with this internet-connected, RAPT-enabled Cannular Can and Bottle Filler, offering a more sanitary and user-friendly experience than competitors.
Integrated Pinch Valve and Regulator: The pinch valve allows easy removal of the beer line for cleaning, while the integrated regulator eliminates the need for an external regulator, preventing damage from high-pressure gas sources.
OLED Digital Display and WiFi Connectivity: The OLED display simplifies calibration and allows real-time adjustments, while WiFi connectivity to the RAPT.io portal logs usage data and enables remote management of settings and profiles.
Versatile and Multi-Purpose: With adjustable stainless steel tubes and a height range suitable for bottles up to 11.8" and cans up to 10.6", this filler can handle still or carbonated beverages, making it ideal for various containers including wine bottles, beer cans, and more.
Low Dissolved Oxygen (DO) Pickup: The filler effectively purges oxygen from the container, ensuring substantially lower dissolved oxygen levels, which enhances the quality and longevity of your beverage.
Fill any beverage into any bottle, can, jar, or glass automatically with this internet-connected, RAPT-enabled, Cannular Can and Bottle Filler. Featuring two adjustable stainless steel tubes, the Cannular Filler will use one to purge oxygen out of the vessel and then use the second one to fill the vessel to a precise level based on an internal pressure sensor.
OLED Digital Display
The OLED display makes calibration super easy. It also enables you to keep track of filling speed, number of cycles/fills, purge time, fill height, and also enables you to make on-the-fly adjustments to your filling requirements so you can conveniently tweak the settings while filling.
Integrated Ball Lock Connectors
The integrated ball lock connectors allow you to quickly attach your beer and gas ball lock disconnects. We recommend the use of the Duotight Ball Lock Quick Disconnects in Gas and Liquid to connect to these inputs and outputs.
Integrated Pinch Valve
The integrated pinch valve is one of the things that makes this unit far superior to other filling machines. The pinch valve enables you to easily remove the beer line for cleaning so the stainless tube, silicone hose, and yellow ball lock cap removes completely and can be put into the dishwasher or cleaned in the sink. The pinch valve is mechanically simple and therefore reliable. It is not subject to small particles like hops getting stuck in the device and eliminates the need for pre-filtration. It simply pinches down on the silicone tube to shut off the flow. This design also enables laminar flow that reduces foaming. The pinch valve improves reliability, makes it easier to operate, and a piece of cake to clean.
Integrated Regulator
Other filling machines require an external regulator that may need to drop the pressure lower than your normal keg dispensing pressure. Unlike these other fillers, this filler has an integrated regulator which saves time and setup costs. This integrated regulator means you will not damage your machine by accidentally connecting it to a high-pressure gas source. You can hook up your gas line without the need for another external regulator or to fool around with your gas supply at all. Just set the integrated regulator once during setup and forget about it.
Multi-Purpose
The long stainless tubes and adjustable height make this device useful for pretty much any bottles up to 11.8" (30cm) high or cans up to 10.6" (27cm) high. It can also be used for still or carbonated beverages, so this device is useful for wine bottles, beer cans, champagne, crown seal bottles, and pretty much any other bottle/can/vessel that has a neck opening greater than 0.59" (15mm). It can also be used for filling glasses, jars, or other vessels.
Fill Profiles
Some other machines require a full calibration to change from one vessel type to another. This machine allows you to pre-save fill profiles depending on what you are doing. Save a filling profile for your 12 oz cans and then save a different filling profile for your 750mL wine bottles. Use our pre-saved presets or alternatively make your own fill profiles with different purge times and fill height. These are also synced with the RAPT.io portal so you can save profiles and share them with friends or deploy them to several other devices.
RAPT.io Connected (via WiFi)
As well as all the features above, this filler connects to your WiFi and keeps track of your Cans Per Minute (CPM), fill speed, and even temperature (if you purchase the external Instant Read Temperature Probe separately). It will log all usage information so you can keep track of how your machine is running or even keep track of your staff to make sure they are cycling the machine at an acceptable rate. The connectivity to the RAPT.io portal will enable you to more easily change settings, update profiles, and keep track of your fill days so you can historically keep track of how your fill day went and which day you processed each batch.
Low DO Pickup
The quality and longevity of your beverage are often defined by how well you keep oxygen off your product. This filler purges the oxygen out of the can and will enable you to get substantially lower dissolved oxygen.
Wall Mounted Design
This type of can and bottle filler has primarily been designed for wall-mounting configuration. This allows you to bring a can or bottle up to the filler from the underside of the unit. To wall mount this unit you can download and print this template.
24V DC Power Supply
KegLand Part Number: KL37785
RAPT Can Filler User Guide
The Hop Bong is a versatile pressurizable tri-clamp accessory, capable of not only dry hopping oxygen purged hops into fermenters, but also as an inline carbonation/oxygenation accessory. This particular sized tri-clamp Hop Bong was designed for the BrewBuilt X-Series Uni Conical fermenters for their 1.5" T.C. lid port. The side port features PCO1881 male threads so you have the option to add a Ball Lock Cap. When used as a dry hopping device on top of your fermenter, this will allow you to purge your additions of oxygen by flushing them with CO2. When used as a sight glass below your fermenter (if your conical has a 1.5" bottom port, or if you use it along with a 2" x 1.5" reducer), bubble CO2 from the bottom up via the Ball Lock Cap to rouse hops or carbonate finished beer. Constructed from Nylon 12: An autoclavable, extremely robust, and chemical resistant engineering plastic. Hop Pellet Capacity: 80–120g (2.8–4.2 oz) KegLand Part Number: KL26062
Elevate your brewing game with the 220V 17 Gallon Gen 4 BrewZilla. This cutting-edge system combines more power & capcity with innovative features like wireless connectivity via WiFi & Bluetooth, allowing you to heat faster while you control and monitor your brew day, ensuring precision, convenience, and exceptional beer batch after batch!
WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal
The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench
Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter
Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation
Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency
Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp
The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve
Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps
More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet
WiFi/Bluetooth Enabled RAPT Controller
The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen.
But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability.
And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer!
But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings.
Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road.
High Capacity Malt Pipe
With an approximately 41.5 lb capacity, the BrewZilla can mash nearly 20% more grain than similar sized models of the Anvil Foundry and Grainfather G70. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency.
Concave Base with Center Draining
Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind.
Ultra Low Watt Density Elements
The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy.
Easy Access Built-In Pump
The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet.
If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer.
MoreBeer!'s Final Word
We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included.
Perfect for Distillation
If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find.
Features:
Gen 4.1
Stainless steel construction
17.1 gallon total capacity with a finished beer output of 10-12 gallons
WiFi/Bluetooth Enabled RAPT digital temperature controller
Automatic step mashing with 6 programmable stages
220-240V power
NEMA 6-30P plug
Requires NEMA 6-30R receptacle
Requires 16 amps from 30 amp circuit
Triple heating elements (2000, 1000 and 500 watts)
Stainless steel 1/2" ball valve for gravity draining or transferring via pump
Immersion wort chiller included
Stainless steel malt pipe/basket
Stamped in volume markers
Glass lid
Adjustable lid clamps (do not use with glass lid in place - see below)
Magnetic drive pump for recirculation, transfers, and cleaning
Recirculation arm
PPSU sight glass
Bottom handle for easy lifting and pouring
Rubber feet
Temperature reads in °F or °C
Approximately 36" H (with recirculation arm) x 16" D
Recommended max. grain bill: 41.5 lbs
AlcoEngine Still ready with the purchase of a Distillation Lid
Pump Specs:
Max Flow: 5 gal/min
Max Head: 11 ft.
Voltage: 220–240V-AC
Frequency: 50–60Hz
Power: 25 watts
Fittings: 1/2" (13 mm) barbs
You Will Need:
2' of H985 1/2" ID Silicone tubing for sparging and draining.
To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950hose clamps and (1) brass hose by thread adaptor (H508).
These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout.
KegLand Part Number: KL27458
Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos.
Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe.
Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories.
Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.
35L (110V)
35L (220V)
65L (220V)
100L (220V)
10 ft.
14 Gauge
14 Gauge
12 Gauge
10 Gauge
25 ft.
14 Gauge
14 Gauge
12 Gauge
10 Gauge
50 ft.
12 Gauge
12 Gauge
10 Gauge
8 Gauge
RAPT Gen 4 BrewZilla | User Manual
The redesigned FermZilla Collection Container attaches directly below the fermenter without the need for a screw top adapter piece Replace your existing 600mL, keep a spare on hand, or upgrade from the original tri-conical collection container with the 3" x 3" Tri-Clamp Butterfly Valve Made from heat resistant, plasticizer-free Tritan plastic and dishwasher safe PCO1881 side ports for use with Ball Lock Carbonation Caps and the PRV Cap Combo 3" tri-clamp, gasket, and end cap included This collection container fits all FermZilla Tri-Conicals with a 3" x 3" Butterfly Valve. No more threads or oil filter removal tools to get this off, simply depressurize and remove the tri-clamp fitting. We recommend placing a towel or upside down frisbee to catch some drips. The clear body is made from Tritan from Eastman Plastics which is heat tolerant and BPA- and plasticizer-free. The ports on the side are the same as a standard coke bottle or soft drink bottle (PCO1881). These are also the same on the top of the FermZilla lid and the previous model collection container. Owners of the FermZilla Tri-Conical that came with the 2" T.C. collection container can upgrade to this collection container by swapping their butterfly valve to the 3" x 3" Tri-Clamp Butterfly Valve. Recommended Accessories: 1 x Ball Lock Carbonation Cap (FE13 or FE146) 1 x Red PRV Cap Combo (KG524) Includes: 600mL Tritan Plastic Collection Container 3" Tri-Clamp Ferrule PCO1881 Carbonation Cap Ports 3" Tri-Clamp (3-Piece) 3" Tri-Clamp Silicone Gasket 3" Tri-Clamp Black Polyketone End Cap Dimensions: 6.7" Tall Tapers from 3" ferrule down to 2.5" diameter bottom KegLand Part Number: KL3036
The Hop Bong is a versatile pressurizable tri-clamp accessory, capable of not only dry hopping oxygen purged hops into fermenters, but also as an inline carbonation/oxygenation accessory. This particular sized tri-clamp Hop Bong was designed for the FermZilla Tri-Conical and All Rounder fermenters with the new Tri-Clamp Adapted Pressure Lid. It can also be adapted to any 2" T.C. port in your system to use either inline or as a dry hopping device. The side port features PCO1881 male threads so you have the option to add a Ball Lock Cap. When used as a dry hopping device on top of your fermenter, this will allow you to purge your additions of oxygen by flushing them with CO2. When used as a sight glass below your fermenter, bubble CO2 from the bottom up via the Ball Lock Cap to rouse hops or carbonate finished beer. Constructed from Nylon 12: An autoclavable, extremely robust, and chemical resistant engineering plastic. Hop Pellet Capacity: 150–180g (5.2–6.3 oz) KegLand Part Number: KL26079
Monitor and adjust your fermentation temp settings remotely via internet connection
Set customized temperature profiles that will run automatically
Access the RAPT portal to review previous fermentation temperature logs
Red & Blue power sockets to clearly identify your heating and cooling outlets
For untethered probe readings, switch the temp reference to the RAPT Bluetooth Thermometer
Mobile RAPT app available of iPhone and Android
The RAPT WiFi-enabled temperature controller allows you to monitor, track and control heating and cooling devices remotely via any internet connection. Log in to the RAPT portal from any web browser, or download the RAPT app from the Apple App Store for iPhone or Google Play for Android. From the portal, set up your own complex temperature profiles and the RAPT controller will make the temperatures adjustments automatically according to your schedule. The color screen clearly displays temperature, graph of future and past temperature settings and makes it much easier to perform profile temperature steps.
This plug and play temperature controller has two clearly marked blue and red power sockets for heating and cooling so you can control a fridge or heating device at the same time to completely monitor and control the temperature. Each 110V power outlet is rated to 10 amps (1200 watts max).
PID Included
This temp controller box comes with PID heating function often used for higher powered devices. This greatly reduces the chance of scorching and will deliver better temperature control with less fluctuation.
Temperature Range
The temperature range of this device will enable you to control devices from -4°F to 248°F (-20°C to 120°C).
Various Mounting Options
This innovative design enables you to panel mount this controller, mount to a hanging point or hook, mount on top of a fridge or brew system. Simply unscrew the mounting plate and switch the mounting to your preferred orientation. A mounting plate is included with controller, and you can even adjust the routing of the cords to come out the back of the controller, allowing you to stand up the controller and set it on a table or benchtop.
RAPT WiFi Compatible
This product will connect with the RAPT portal. This portal will enable you to monitor, control and log past temperatures, and also show a future projection of temperature profiles that you might have running.
What is RAPT?
RAPT is a dedicated Internet of Things (IOT) Hub for fermentation logging and control. It's a free service whereby any RAPT-enabled product can both log and store data to the hub where you can conveniently access it. The RAPT hub can also allow you to control your devices remotely giving you absolute control of the device irrespective of where you are. The RAPT portal enables you to make complex temperature profiles that involve different temperature settings over time meaning you can start/run a temp profile giving you a set and forget experience. The RAPT portal also controls the alert/notification process for you so you can receive email notifications in the off chance that something doesn't go to plan.
Specs:
WiFi & Bluetooth Enabled
Free companion app available for iOS or Android devices
Customize temp profiles and view logged data from the RAPT portal via web browser
Simple plug and play design with LCD display
Adjustable heating/cooling differentials
Temp Range: -4–248°F (-20–120°C).
Probe Relay Length: 6.5 ft. (2 m)
Probe Diameter: 0.15" (4 mm)
110-120V 15A
KegLand Part Number: KL2605
RAPT Temperature Controller User Manual
Aerate your wort automatically with this complete aeration system. Includes compact air pump, air filter, diffusion stone, and EVABarrier tubing. This aeration system diffuses oxygen into your wort using the air around you, so there's no need to buy pure oxygen cylinders again and again. The down side is that aeration takes longer than oxygenation. Because the atmosphere is only about 20% oxygen, the diffusion stone must be left running in the wort for approximately 30–120 minutes (but even 5 minutes of aeration is better than shaking the carboy). The sterile filter will prevent contamination during this period, but you will need to monitor the fermenter periodically for possible over foaming. To clean your stainless stone, we recommend boiling it for several minutes and storing it in a zip lock bag between uses. It can clog easily with the oil in your fingers, so use gloves when attaching it to the tubing. NOTE: You will need to use hot water to soften the 4 mm x 8 mm EVABarrier tubing when attaching the stone. Needle nose pliers can help to widen the tubing, if necessary. Hose clamps won't be required once it's attached. You will also need to cut a short piece of tubing to bridge the connection from the air pump to the air filter and the air filter to the diffusion stone. You do not want the air filter to get wet or be inserted into your fermenter, so keep the air filter close to the pump. The sanitary air filter can last up to 1 year, but should be replaced if there are any signs of discoloration. Includes: CE Air Pump 15 micron sintered stainless stone with barb 0.2 micron autoclavable air filter Approximately 5 ft. of EVABarrier tubing (4mm ID x 8mm OD) KegLand Part Number: KL03926
The Alembic Copper Domed lid will help you achieve a smoother, richer, sweeter tasting spirit by helping to remove unwanted sulfur compounds. The large copper surface area acts as a catalyst with distilling vapor to enhance and concentrate flavors and aromas during the distilling process. Primarily intended for use with the Copper Pot Still, but it can also be used with the Copper Reflux still if desired. Note: This lid uses a 6mm gasket to better fit the Gen 4 BrewZilla and Gen 2 DigiBoil. It is also backwards compatible with Gen 3 and older BrewZillas and Gen 1 DigiBoils. To improve the seal further, we highly recommend using the Adjustable Lid Clamps with the Distillation Lid if your unit does not have them. 9-1/2" Tall 12-3/8" Diameter. Please note that copper is a very soft metal and can be dented quite easily. Store and use with care. KegLand Part number: KL1589 Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States. It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA).
This Duotight to 3/4" female thread fitting can be used to connect beverage or gas line to any fitting with 3/4" MPT. Compatible with EVABarrier 9.5 mm OD Tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL13864
This Set of 12 Mini Liquid Chalk Markers utilize water-based pigment ink so you can mark on windows, glass, mirrors, plastic and metal surfaces with ease. The ink won’t wash off in the rain, yet is easy to remove with a damp cloth. For permanent application the markers can also be used on chalkboards for a bold statement. If using the MoreBeer! Recipe Kit Tap Handle, we recommend using these chalk pens on the back of the tap handle rather than the chalkboard insert. The chalkboard insert is porous and will let the ink set in, whereas the back of the tap handle is smooth and will wipe clean more easily. Each marker has a 1.5 mm bullet tip The markers are ideal for signage and can be used indoor and outdoor The ink is made using a water-based formula and each color is vibrant and opaque This marker contains white colored ink The ink is removable on non-porous surfaces KegLand Item Number: KL20206
Camlock to tri-clamp adapter. Perfect if you prefer camlock fittings on your tubing lines and own a brewing kettle, pump, or fermenter with tri-clamp fittings.
Male camlock fitting x 1.5" tri-clamp. Made from 304 stainless steel.
KegLand Part Number: KL20237
For clean, straight cuts this 2-in-1 cutter is hard to beat. Developed specifically for EVABarrier draft line, but compatible with any tubing that is 3/8" OD or smaller. Features an 8mm jaw on the back to easily pull the collet back when removing line from Duotight fittings.
Kegland Part number: KL07689
PCO38 threaded tapping head pairs perfectly with Oxebar Mono PET Kegs for a lightweight, affordable draft dispensing system
Dip tube features a filter attachment to keep solids in the keg and out of your glass
Includes liquid and gas ball lock posts and pull-ring PRV rated to 36 psi
Now includes PCO38 Gen2 black elbow cap insert
This handy PCO38 Tapping Head assembly is a great way to get into kegging. Using standard homebrew ball lock disconnects, this is a convenient, light weight, robust and inexpensive solution to kegging beer, cocktails, kombucha, wine, and other beverages.
This PCO38 tapping head assembly has been designed to suit standard PCO38 bottle necks such as the 4L or 8L Oxebar Mono PET Keg. KegLand utilizes quality engineering plastics and efficient injection stretch blow mould processes to manufacture economical kegs and tapping heads for both homebrewing and commercial beers. The plastics used in the tapping head can withstand a wide range of chemicals used in the brewing industry and relatively high temperatures (212°F / 100°C).
The Ball Lock Tapping Head kit comes with 2.5 BAR (36 psi) PRV, liquid and gas ball lock posts, and dip tube with filter attachment.
KegLand Part Number: KL2714
NOTE: The Oxebar Mono Keg shown in the example photos is sold separately.
For all you hop bongers out there. We have an end cap for all end caps! Compatible with multiple PCO1881 accessories. Made from high quality engineering plastic and will last a very long time. It's chemically resistant and also designed to resist impact and physical damage. The Hop Bong features a molded PCO1881 port, but depending on your application you might need a second. If using to dry hop, you'll use the Hop Bong port to add CO2 with a Ball Lock Cap and then attach the PRV Cap to the Hop Bong Cap to purge the gas. Use with the 1.5" Hop Bong to attach: Red PRV 1881 Cap Combo Red Ball Lock Cap Yellow Ball Lock Cap KegLand Part Number: KL23610
It is really THAT easy to make good beer at home?+
YES! If you can follow a recipe and keep clean, there is nothing stopping you from making great beer in your home - beer you can be proud of and your friends will love! The MoreBeer! mission is to provide reliable equipment and quality ingredients that make the home brewing experience successful and satisfying. We'll get you started in home brewing the way we wish we had been started.
