KegLand is a high quality homebrewing equipment brand based out of Australia. We offer a wide variety of their products, from BrewZilla all-in-one system and DigiBoil eletric kettles, to pumps and grain mills. KegLand beer products are an incredible value, as they combine quality craftsmanship with low prices!
Small diameter tubing intended for use with water filtration systems and RO systems 150 PSI pressure rating—well-suited to handle your mains water pressure Made from polyethylene. BPA & plasticizer free Compatible with all Duotight and Monotight fittings with 6.35mm ends This PE (polyethylene) tubing is not only BPA and plasticizer free but it's also NSF approved. Suitable for pressures up to 150 PSI so it will have no problem handling your household's mains water pressure. This type of tubing is commonly used with water filtering systems and reverse osmosis (RO) systems. Compatible with the KegLand Solenoid Valve. Can be used with the 6.35mm Duotight In-Line Regulator to drop your mains water pressure if needed. This tubing is compatible with all Duotight and Monotight fittings with 6.35mm ends. Specifications: 5/32" ID x 1/4" OD (4mm x 6.35mm) 33 ft. Roll Pressure rated to 150 PSI Made from polyethylene BPA & Plasticizer free NSF approved KegLand Part Number: KL11143
Designed to offer a sturdy connection point when using medium-heavy stills or off-center steam condenser units. To attach an AlcoEngine Still Top, remove the locking ring and gasket, replace the gasket with this single sided bead seal, pass the bottom threaded portion of the still through the ferrule, and secure in place with a 2" tri-clamp.
Sized for 35L BrewZillas and DigiBoils.
Compatible with the AlcoEngine Copper Pot Still and Copper Reflux Still and the BrewZilla Steam Condenser.
Installing AlcoEngine Still:
Remove the bottom nut and seal from the column
Place the single sided bead seal on the lid's tri-clamp ferrule (beaded side facing down)
Pass the threaded bottom section of the column through the ferrule
Secure in place with a 2" tri-clamp
The column's bottom nut and seal are not needed
KegLand Part Number: KL32629
Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets.
For 2" tri-clamp fittings.
KegLand Part Number: KL03438
Weighted cap design keeps the dip tube submerged, maximizing liquid draw and minimizing air intake for consistent performance Prevents hop material and other sediment from clogging your dip tube, ensuring cleaner beer transfers and samples Works seamlessly with Torpedo Keg Buoys, Kegmenter Floating Dip Tubes, and FermZilla Pressure Kits for diverse brewing setups Made with food-grade HDPE and 304 stainless steel, allowing for easy cleaning and sanitization with common brewing cleaners This handy little filter attachment can be used with the Torpedo Keg Buoy, Kegmenter Floating Dip Tube, or FermZilla Pressure Kit to keep hop material from being sucked into the silicone dip tube. This upgrade accessory is especially helpful if you like to dry hop directly in your keg while serving, or if you want to pull clean samples from your FermZilla or Kegmenter during fermentation when there's still a lot of biomatter in solution. Simply remove the metal tube from the ball float, slip the silicone tubing over the barb, then reattach the ball float to one of three clip locations. Made from HDPE and 304 stainless steel, the filter can be boiled or sanitized with the full range of cleaners that we sell. The plastic HDPE is over molded onto the stainless mesh to make a seamless finish. The end cap can easily pop off for cleaning. This updated version of the original Filter Attachment now includes a weighted cap that helps keep the end of the dip tube pointed down and submerged below the liquid surface level. KegLand Part Number: KL41485
96% reduction in oxygen ingress compared to silicone O-rings when measured in a keg!
Made from a special blend of materials, these gaskets offer vastly improved oxygen barrier properties compared to Silicone or EPDM
Give your beverage the absolute best protection from oxygen staling with KegLand's Low2 O-rings!
The result is your beverage staying fresher for longer!
Compatible with any ball lock or pin lock corny-style keg with standard lid
Upgrade the storage life of your beer by replacing your standard keg lid O-ring with the new Low2 O-ring from KegLand. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer.
Compatible with any ball lock or pin lock corny-style keg with a standard size lid. Not compatible with Megamouth Torpedo Kegs.
Low2 O-rings were independently tested by GunnLab, an Australia-based plastic packaging testing laboratory. See below for a printout of the test results.
KegLand Part Number: KL03063
Forward-sealing design prevents beer residue from gumming up the faucet!
Threaded spout can be replaced with a variety of attachments
Unique sliding shuttle design allows the faucet to last longer than standard floating o-ring design
304 stainless steel construction
The patented Stainless Steel Intertap Faucet is a forward sealing faucet that represents the most modern faucet design. It has a modular, threaded spout which can fit a variety of different attachments including a growler filler or a stout spout.
In normal rear-sealing faucets the entire faucet has to drain of beer. In forward-sealing faucets the faucet keeps beer in it so the inside doesn't have a chance to get sticky, making cleaning much easier. It also reduces the chance of off flavors transfering to your beer while you pour.
Other forward sealing faucets use a floating o-ring, which is just as sanitary but requires the o-ring to move inside the faucet body in order to seal correctly. This can become a problem as the faucet ages. Intertap faucets use a sliding shuttle that guides the o-ring into the perfect position every time.
The threaded spout easily unscrews from the faucet and can be replaced by a growler filler or stout spout quickly and easily. Pour a pint and then fill a growler in no time at all.
304 Stainless Steel construction so you don't have to worry about chrome plating wearing off and exposing your beer to brass.
Kegland Part number: KL00970
Replacement Wire Malt Pipe Support for 35L BrewZilla. Made from 304 stainless steel.
This is the "Gen 2" version of the wire support ring. It has been slightly modified from the previous version to be compatible with all generations of BrewZillas and DigiBoils.
KegLand Part Number: KL88020
Who doesn't love a well-organized kegerator or keezer? The Beer Line Tidy from KegLand offers an easy solution to straighten out your rat's nest of draft lines. Simply remove the paper backing and use the strong 3M adhesive to attach this beer/gas line organizer to whatever device you like. This keeps your beer and gas plumbing neat and tidy so your draft system looks as good as it works.
Primarily designed for 8 mm (5/16") OD tubing, but works with 9.5 mm (3/8") OD and 6.35 mm (1/4") OD tubing as well.
Note: for best results, apply the adhesive at room temperature and let stand for 72 hours before applying load.
KegLand Part Number: KL22767
Stainless steel tri-clamp reducing elbow. Specifically manufactured as an alternative for the FermZilla 27L and 55L Tri-Conical bottom dump port. If you would like to bypass the 3" x 2" butterfly valve and collection container on your FermZilla Tri-Conical, you can use this reducing elbow to go directly to a 1.5" tri-clamp valve.
KegLand Part Number: KL29469
KegLand put an exceptional amount of time into the research, testing, and development of the MaltZilla, and what they came up with is a motorized grain mill unlike anything we've seen before. It features an integrated motor so you'll never have to mess with a hand crank or power drill to spin the rollers. And the rollers themselves are made with a diamond-impregnated surface that offers superior performance and longevity compared to conventional knurled steel rollers. The integrated 24V motor is powerful enough to chew through popping corn kernels with ease, and works on voltages from 12-30V DC. The higher the voltage the faster the rollers spin, although we recommend 24V for optimum speed and grist results. The unit does not come with a power supply. When purchasing the unit, you have the option of pairing it with either a power supply with 110V plug (CAN11), or with a 6 ft. long cord with Anderson plug and alligator clips (CAN102). The power supply is straight forward, and allows you to plug the unit into a standard 110V power socket. The alligator clips give you the option to power the unit from a battery. Knurled Steel vs. Diamond Coated Rollers
Your run-of-the-mill grain mills are often manufactured with steel rollers with a knurled finish. The knurling helps grip and pull the grain through the rollers, but even the knurling on hardened steel will go blunt eventually and hinder the mill's performance. Some manufacturers attempt to solve this problem by using geared rollers to better grab the grain, or add a third roller to the mill so the first two rollers with a larger gap force the grain into the third roller. These are only workarounds to the real issue—all steel rollers will go blunt eventually, especially if used with hard grains like wheat or corn. In a commercial setting, it’s not uncommon to send the rollers off to a metalworking factory to re-sharpen and re-knurl, but this is an expensive, time-consuming hassle. Many homebrew-scale users might just end up throwing the mill away and purchasing a new one. The MaltZilla Diamond Mill is quite a different mill design, and it’s the first in the world to use diamonds impregnated into the surface of the roller. Even after many tons of grain are processed through the mill, the diamond surface will stay just as sharp as it was on day one. The sharpness of the diamonds draws grain exceptionally well, and even when hard grains are used the diamond rollers won't dull or slip in performance. Sheer Instead of Chop
Most mills require aggressive knurling to push into the grain and “chop” the grain as it passes through a tight gap, which means your grains are often chopped in half. The MaltZilla works on a different principle and gap setting is not as critical. The MaltZilla uses impregnated diamonds to grip the surface of the kernel and the friction of pulling the grain through the gap causes a sheering action. When set up correctly, the sheering action can leave the entire husk intact, reducing the chance of stuck sparge and improve efficiency, while still opening the husk enough that the entire contents of the kernel is available to the mashing process. The 70 mm diameter rollers are double the diameter of many other mills, which significantly improves the crush and assists in drawing the grain in more effectively. Integrated Motor
You generally would not purchase a car without an engine, so why would you purchase a grain mill without a motor? Milling grain has an optimum RPM— too slow and it will take you a long time, too fast and you will end up with excessive powder. Hand cranking can be a pain in the backside, especially with larger grain bills, and using a power drill doesn't offer much in the way of speed control and adds the potential risk of burning out your drill. The MaltZilla has an integrated motor with a very constant RPM putting out optimum RPM with an integrated gearbox. The high torque and sealed construction make it ideal for a brewing environment, as the motor is well protected from moisture and grain dust. The motor is seamlessly integrated into the side body of the mill. Being DC, the motor is safer than higher voltage AC, especially in an environment where splashing and hose spray are commonplace. The DC motor is also reversible so the direction of spin can be changed based on the polarity. This is particularly useful for over-mount and under-mount installation. Over-Mount and Under-Mount Installation
Traditionally, homebrew mills just sit on a board where they are moved from one bucket to another. The MaltZilla has multiple different mounting configurations. It can be over-mounted to a board like most mills are, but if you want a seamless finish to your garage/brewing area, you can mount the mill under your counter where it’s concealed and out of the way. Simply lift up a small opening in the top of your benchtop, drop in your hopper, pour in grain and run the mill. When you're done, remove the hopper and conceal the opening. There is also a MaltZilla PPE Base Board available for over the bucket installation or designing your own mill stand. Grain Hopper
This unit does not come with a grain hopper. We recommend using a large funnel with a shortened spout, or a repurposed gallon-sized water bottle. The MaltZilla Aluminum Hopper is currently in development and available for pre-order. Specifications:
Power: 12-30V DC Anderson Connector Plug Grain Inlet ID: 2-3/16" Grain Inlet OD: 2-3/8" Weight: 11 lbs KegLand Part Number: KL15776 Please note: This mill is designed for use with brewing grains only. It will not work for cracking whole kernel corn.
These Polypropylene (PP) Measuring Cylinders are virtually indestructible. When it comes to brewing and winemaking, these will serve you a lifetime of use. Long gone are the days of dropping your glass measuring cylinder when taking a hydrometer reading, not only leaving you with a mess to clean up but also the need to scramble for another vessel to take a reading.
The measuring cylinder has a wide sturdy base with a 28 mm (1.1") internal diameter. Approximately 24 cm (9.4") tall with 1 mL graduations, ideal for hydrometers and alcometers.
Polypropylene (PP) Is also acid and alkaline resistant, so it can also be used to measure a large range of chemicals.
KegLand Part Number: KL04039
The Drafto Kit is a great addition to any Ultimate Growler (GL750) that allows you to pressurize and preserve your beer for longer. Never have your growler go flat again! It's simple and easy to use; just replace the the original cap on your Ultimate Growler with the Drafto Kit, attach a mini CO2 regulator, pressurize and serve. Note: Does not come with CO2 regulator or cartridge. They must be purchased separately. We suggest one of our mini CO2 regulators (KEG965A) and cartridge (KEG962) or (KEG96) and cartridge (KEG993). Please Note: This unit Should Not be used with unregulated CO2 sources. Kegland Part number: KL0429
Perhaps your wort was too hot when you transferred from the kettle, or while cleaning you dropped the FermZilla against something sharp that punched a hole, or maybe it's just time to replace the tank after acquiring too many scratches from normal wear-and-tear. Whatever the reason, no need to go buy a whole new FermZilla! Just pick up one of these fresh replacement tanks and your conical fermenter will be good as new! Pressure Stress If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple: Fill the tank to the brim with water Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher Pressurize the tank to 4 BAR (58 psi) Check for leaks, then replace the Red PRV when finished If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla. General Care Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank. KegLand Part Number: KL15219 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.
The Gen 2 DigiBoil features two distinct updates that are not currently pictured in the primary images. The stainless steel lid has been upgraded to a glass lid, allowing you to observe and monitor boil activity. The rubber feet have been replaced with a plastic base that provides improved stability and slightly raises the unit for better ground clearance. Updated images coming soon.
The most affordable all-in-one automated all-grain brewing system!
Mash grains and boil wort in a single vessel
DigiBoil electric kettle automatically maintains mash temperatures with the digital controller
Dual heating elements combine for 2400W of power
Also available with optional Recirculation Pump Kit!
The DigiMash system represents the best value in electric all-grain brewing you'll find. With a 9-gallon DigiBoil electric kettle and the DigiMash stainless steel mashing accessory pack included, this is by far the most affordable way to get into electric all-grain brewing. It may not have all the bells and whistles of the BrewZilla, but it does have everything you need to mash and boil all in one unit. Setting up and using the DigiMash couldn't be easier. Simply place the false bottom inside the kettle and install the malt pipe, fill with water and heat to your desired strike temperature, then add your grain and set your desired mash temperature on the digital controller. Once your mash is complete, lift up the malt pipe, drain the wort and sparge, then remove the malt pipe and proceed to boil.
If you're deciding between the DigiMash and the BrewZilla, there are a couple of key differences worth noting. One of our favorite features of the BrewZilla is the programmable mash steps and delayed start, which the DigiMash does not have. You can still step mash by simply raising the temperature manually on the controller, but the automatic steps are a convenient feature if you want to set it and forget it.
The other major difference between the two systems is that the BrewZilla features a built-in pump for recirculating the mash. Recirculation is a great way to improve mash efficiency, but it is far from required for a successful brew day. Using an external pump with the DigiMash is also an option, and one can be integrated for mash recirculation quite easily. Simply connect the ball valve to the inlet of your pump, and then connect the outlet of the pump to our Sparge Arm Assembly.
This model comes with the 35L DigiBoil, which has two built-in heating elements that run off a 220V plug. One element is 1900w and the other is 500w for a combined 2400 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage both elements to quickly go from mash temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s).
If you have access to 220V power, this is definitely the unit we recommend. Although 110V power is enough to get up to boil, 220V will get you there faster and provide a much more vigorous boil.
Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach fittings with 1/2" FPT, such as our female threaded quick disconnect.
DigiBoil Features:
304 stainless steel construction
9 gallon total capacity
Digital temperature control
220V / 15A power
NEMA 6-30R plug (5 ft. cord)
Dual heating element control (1000w and 500w)
Heating elements are concealed for easy cleaning
304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2")
Stamped-in volume markers (gallons & liters)
Stainless lid
Temperature reads in °F or °C
With elements turned off, hold both +/- buttons to switch between °F or °C
Recommended max. grain bill - 18 lbs
Recommended min. grain bill - 8 lbs
External Dimensions: 29" H x 15" W (including handles)
Internal Dimensions: 19.5" H x 11.75" W
ETL Listed
DigiMash Upgrade Includes:
False bottom
Malt pipe
Wire support
Malt pipe handle
Malt pipe bottom screen
It may just look like an oversized keg at first glance, but the 1 bbl Kegmenter can do so much more! These stainless steel vessels are perfect as a pressure fermentation vessel, storage brite tank, or even a large-batch home still. Welded tri-clamp openings offer versatility for rigging up this unit however you see fit. Large 4" tri-clamp opening at the top and two 2" tri-clamps ports at the bottom. The large 4" opening at the top makes it easy to get inside the keg for cleaning, and the 2" ports at the bottom can be fitted with valves, heating elements, or other TC accessories and fittings. The kegmenter is well suited for use as a fermenter, brite tank, or top-up barrel. The 1 bbl Kegmeneter comes with end caps and clamps to plug the bottom ports, and a pre-drilled 4" cap for the top opening with a stopper and airlock included. You also have the option to use the Ball Lock Post lid with floating dip tube, which can be used for pressure fermentations or transfers. Also a 4" x 2" TC reducer would allow for adding a Reflux or Pot Still for distillation. Also consider the Kegmenter Hop Bong Pressure Pack which allows for oxygen-free dry hopping and also features ball lock posts for Gas & Liquid. Specifications: Volume: 1 bbl (31 gal) Working Pressure: 3 bar (43.5 psi) Made from stainless steel 41" H x 15.5 Ø Kegland Part number: KL04541
If you are an experienced single vessel brewer and don't use the overflow pipe. This malt pipe screen is the perfect upgrade for just that! The Gen 4 BrewZilla nixed the overflow pipe, so this is a direct replacement part for that unit. But this screen can also be used with the Gen 3 BrewZilla if you don't use the overflow pipe.
KegLand Part Number: KL14236
The Copper Pot Still is perfect when you want the flavor of the wash to come through, whereas a Reflux Still is more favorable for producing pure, unflavored spirits. If you want to make whiskeys and gins, this pot still top is a great way to start! The classic "V" shape captures the vital esters, aldehydes, and phenolic compounds that are necessary for the complex spirits such as whiskeys and gins. Made from solid copper. When your hot spirit comes into contact with the copper, the copper acts like a catalytic converter to drive sulfur out of the spirit. This leads to less off-flavors and higher quality spirit. This is only the still top and does not come with a boiler. This is only the still top and does not come with a boiler. Combine with a distillation lid to use a BrewZilla or DigiBoil as the base for this Alcoengine brand still top. Comes with 13 mm (0.51") barb connections for the water inlet and outlet. Kegland Part number: KL1615
A best seller for a reason! Tons of features at an incredible cost
Crystal Clear super smooth PET makes fermenting and cleaning super easy
3" Butterfly valve at bottom makes removing yeast/trub easy with the 600mL collection jar.
Pressurizable for fermentation and closed transfer to your keg
Includes BlowTie spunding valve kit, red & yellow carbonation caps, and floating dip tube as standard
The FermZilla is the perfect option for brewers that want all the advantages of a conical fermenter without the price tag of a full-blown stainless-steel unit. It allows you to dump trub, harvest yeast, and with the addition of CO2 cylinder and regulator, you can carbonate and serve – all in one vessel! The clear PET tank allows you to visually monitor fermentation activity and is pressure rated to 2.4 Bar (34.8 psi), which means you can ferment under pressure, reducing ester and fusel alcohols in your finished beer. This also gives the ability to perform pressure transfers. If you prefer to move your finished beer to a keg or other vessel, you can do so with little to no oxygen exposure.
The FermZilla Tri-Conical Easy-Grip model comes packed with accessories so you can take full advantage of this pressurizable fermenter on day one. The new stock standard includes Easy-Grip threaded lid ring, BlowTie spunding valve with integrated pressure gauge, ball lock carbonation caps for the lid and collection container, floating dip tube kit with weighted filter, volume marker graduation sticker, and adhesive thermometer.
What's Included:
FermZilla 27L Tank with 3" T.C. Bottom Port
Easy-Grip Threaded Lid Ring
Integrated Gauge BlowTie Kit Spunding Valve (0-15 psi)
Silicone Dip Tube Kit with Yellow Weighted Filter and SS Float
(2) Yellow Liquid Carbonation Caps
(2) Red Gas Carbonation Caps
Fermzilla Pressure Lid with Red PRV (35 psi)
3" T.C. Butterfly Valve
600 mL Collection Container with 3" T.C. Connection
Stainless Steel Stand with Swing Handles
3" tri-clamp with gasket
Graduation Sticker
Adhesive Thermometer
Specs:
27 L (7.1 gal) Total Volume
Pressure Rated to 2.4 Bar (34.8 psi)
Height in Stand - 30.2"
Tank Diameter - 13.9"
Diameter in Stand - 15.3"
Lid & Collection Container Ports - 28 mm PCO 1881 threads
Temperature Rating:
When not under pressure, do not expose to liquids above 131°F
When under pressure, do not expose to any temperatures above 95°F*
*Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years.
Please note: when using the FermZilla under pressure, you must perform a water pressure check to ensure your connections are leak proof. To do this, fill your FermZilla up with water, apply at least 15 psi pressure, and check for leaks around all caps and threads.
Pressure Stress
If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple:
Fill the tank to the brim with water
Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher
Pressurize the tank to 4 BAR (58 psi)
Check for leaks, then replace the Red PRV when finished
If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla.
General Care
Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank.
KegLand Part number: KL47296
NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.
FermZilla Tri-Conical 27L & 55L | User Guide
Serve beverages at different pressures without the need for multiple CO2 cylinders, dual body regulators, or expensive gas manifolds
Feed a single pressure to the gas board from your regulator and then step down the pressure on each Duotight regulator
Use one line for serving ales, another for soda or seltzer water, and another for carbonating a freshly filled keg
All parts shown are included and snap together quickly thanks to Duotight push-to-connect fittings and rigid plastic joiners
Duotight In-Line Regulators feature built-in pressure gauges that read 0-60 PSI and can be swapped out for different ranges if desired
The Duotight Draft Regulator Board is a simple and cost-effective solution to serving beer and other beverages on draft at different pressures. With a standard CO2 tank and CO2 regulator, you can feed gas at a single pressure into the regulator board and then fine tune individual pressure settings for each gas line via the Duotight In-Line Regulators. These regulators feature built-in pressure gauges that make adjustments super simple and check valves are included as standard so you never have to worry about back flow into the regulator. This kit includes everything you need to assemble your regulator board and can be customized so the gas inlet is on the right or left side—whichever makes the most sense for your home draft setup. Duotight push-to-connect fittings and the precut rigid joiners make assembly a breeze and only takes 10-15 minutes!
The draft board kit comes in two options—with or without shut off valves. These valves offer peace of mind and allow you to shut off gas flow to any line that is not in use. If you ensure that your system has no leaks, they aren't technically needed, and you can always fully tighten your Duotight Regulator adjustment knob for added protection. But that little extra security might help you sleep easier at night! One advantage of choosing no check valves, however, is that it will leave room at the top of the board to label your gas lines.
One of the coolest features of the Duotight In-Line Regulator is that the included pressure gauge can be swapped out for different pressure ranges. The standard gauge reads 0-60 PSI, but if you have one line that will always be used for serving Ales, you can swap to a 0-15 PSI gauge that will be a little easier to read and make precise adjustments. There's also a Digital Pressure Gauge available that provides backlit instant reads and is rated from 0-90 PSI.
Need more than 4 gas lines? Check out the 6-Way Duotight Draft Regulator Board.
Please Note: Full assembly required. The gas board, regulators, and fittings will arrive loose. Please see our instructions and assembly video below.
Stepping Down Pressure
The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability.
Ideal regulation scenario (10 PSI less than inlet pressure)
Example of 30 PSI inlet translating to 0–20 PSI output
Kit Includes:
4-Output Gas Board
(4) Duotight In-Line Regulators
(4) Duotight Check Valves
(4) Duotight Shut Off Valves (if selected above)
(3) Duotight Tees
(1) Duotight Elbow
(15) Rigid Plastic Joiners
NOTE: All Duotight fittings and rigid plastic joiners come as 8mm OD. Mounting hardware is included for the regulators but not for mounting the board itself to a wall or the inside of your kegerator/keezer. If you select the option without shutoff valves, you will be left with some spare joiners after assembly.
This Duotight joiner fitting is compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL02370
New Corny Keg ready to use right out of the box New Kegs are trouble-free for years Rubber top and bottoms protect floors from dings Lid includes a tab wth hole welded in so you can hang anything from lid (dry hop our favorite) 304 Stainless Steel and great welds, this will last a tifetime Features Low2 Keg Lid O-ring which offers a 96% reduction in oxygen ingress compared to silicone Ditch the bottles and start kegging today! Save time, reduce the risk of infection and get all those bottles out of the kitchen for good! Brand new 5 gallon Kegland kegs offer convenience, security and insurance when compared to used or reconditioned kegs. There's no need to replace gaskets or other parts, no need to trust that someone else did a good job with reconditioning, and no possibility of residual flavor or aromas getting into your beer! Features: Ball lock 130 PSI Operating Pressure 5 Gallon (19 L) Capacity Dry Hop Tab Welded into Lid 304 Stainless Steel Dimensions: Height: 24.75 in. Diameter: 8.375 in. Kegland Part Number: KL0289
This new American White Oak barrel is made by hand and flamed to a medium toast. A small oak barrel is great for ageing your homebrew, homemade wine or spirits. The exterior is raw unvarnished wood, so take care to keep your barrel in tip top shape. The care guide below will give you instructions on to prepare the barrel for first time use, and also how to keep it hydrated and sealed. Comes standard with a spring-loaded spigot for easy dispensing. An optional stainless steel spigot is also available. Features: 5 L (1.32 gal) American White Oak Medium toast Raw Exterior (Non-Varnished) for easier leak prevention techniques Stainless Alloy Rings coated in a protective black coating Food grade reinforced plastic screw in cork Spring-loaded spigot for easier dispensing Barrel Wax Block Stand included KegLand Part Number: KL04657
These hot fill bladders are a great way to cut time out of your brew day using the "no chill" or "hot packing" method of cooling wort. When your boil is over, simply fill them up and wait for the wort to chill overnight or throw it in the fridge. This eliminates the traditional 30-60 minutes of chill time common in most brew days. Use the wort immediately after it has cooled down, or store refrigerated for short periods of time.
When chilled and ready to go, most brewers transfer the wort out of the bag and into their favorite fermenter. However it is possible to ferment directly in the bag with the use of a #7 stopper and airlock.
Hot packing and the storage of wort at room temperature has been done in Australia as a common practice for decades. Because of the temperature of wort entering the bag, any bacteria are killed. However there does exist a small chance of Botulism contamination for wort that is hot packed and stored. Botulism spores can survive a boil and are only killed through high temperature pasteurization. We always recommend using the wort as quickly as possible once it has cooled.
Hot fillable means they can be filled with any liquid up to 212°F.
The triple layer construction makes these bags puncture resistant, chemical resistant, and gives the bag superior oxygen barrier properties. The first layer is 50-micron polyethylene, the second is 45-micron polyethylene, and the third is 15-micron nylon.
5.2 gal / 20L capacity.
KegLand Part Number: KL18463
These mounting clips feature a swivel design, allowing you to achieve the perfect angle for your tubing layout even after the adhesive is set. The modular design ensures they click together seamlessly and can be detached from the 8mm Duotight side with ease.
Installation Tips:
Surface Prep: For the strongest bond, clean the mounting surface with isopropyl alcohol before application.
Optimal Conditions: Always apply to a warm, dry surface. If installing inside a kegerator or keezer, ensure the unit is turned off and reaches room temperature first; moisture and cold will compromise the adhesive.
Curing Time: Allow the adhesive to set for at least 24 hours before attaching hoses or manifolds.
Recommended for Duotight Gas Manifolds and the Duotight 8mm 5-Way Multi-Tee.
KegLand Part Number: KL48132
The Gen 2 DigiBoil features two distinct updates that are not currently pictured in the primary images. The stainless steel lid has been upgraded to a glass lid, allowing you to observe and monitor boil activity. The rubber feet have been replaced with a plastic base that provides improved stability and slightly raises the unit for better ground clearance. Updated images coming soon. The most affordable all-in-one automated all-grain brewing system! Mash grains and boil wort in a single vessel DigiBoil electric kettle automatically maintains mash temperatures with the digital controller Triple heating elements combine for 3500W of power Also available with optional Recirculation Pump Kit! The DigiMash system represents the best value in electric all-grain brewing you'll find. With a 17-gallon DigiBoil electric kettle and the DigiMash stainless steel mashing accessory pack included, this is by far the most affordable way to get into electric all-grain brewing at the 10-gallon batch level. It may not have all the bells and whistles of the BrewZilla, but it does have everything you need to mash and boil all in one unit. Setting up and using the DigiMash couldn't be easier. Simply place the false bottom inside the kettle and install the malt pipe, fill with water and heat to your desired strike temperature, then add your grain and set your desired mash temperature on the digital controller. Once your mash is complete, lift up the malt pipe, drain the wort and sparge, then remove the malt pipe and proceed to boil. If you're deciding between the DigiMash and the BrewZilla, there are a couple of key differences worth noting. One of our favorite features of the BrewZilla is the programmable mash steps and delayed start, which the DigiMash does not have. You can still step mash by simply raising the temperature manually on the controller, but the automatic steps are a convenient feature if you want to set it and forget it. The other major difference between the two systems is that the BrewZilla features a built-in pump for recirculating the mash. Recirculation is a great way to improve mash efficiency, but it is far from required for a successful brew day. Using an external pump with the DigiMash is also an option, and one can be integrated for mash recirculation quite easily. Simply connect the ball valve to the inlet of your pump, and then connect the outlet of the pump to our Sparge Arm Assembly. This model comes with the 65L DigiBoil, which has three built-in heating elements that run off a 220V plug. The elements are 2000w, 1000w and 500w for a combined 3500 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage all three elements to quickly go from steeping temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s). Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach fittings with 1/2" FPT, such as our female threaded quick disconnect. DigiBoil Features: 304 stainless steel construction 17 gallon total capacity Digital temperature control 220V / 20A power NEMA 6-30R plug (4.5 ft. cord) Triple heating element control (2000w, 1000w and 500w) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Glass lid Temperature reads in °F or °C With elements turned off, hold both the +/- buttons to switch between °F or °C External Dimensions: 29" H x 19.5" W (including handles) Internal Dimensions: 20.25" H x 15.75" W ETL Listed DigiMash Upgrade Includes: False bottom Malt pipe Wire support Malt pipe handle Malt pipe bottom screen NOTE: Due to the size of this item, it is not eligible for international shipping.
This pump does not have a plug. It comes with the appropriate connectors to wire it to the BrewZilla's circuit board. For a brewery pump with similar performance, please see the MKII Pump. This pump now comes standard on the 65L BrewZilla, but if you have an older Gen 4 model with the original 6W pump, you can upgrade to this more powerful unit. The Green Demon This pump comes standard with the 100L BrewZilla Gen 4 and the upgraded 65L BrewZilla Gen 4.1. To upgrade older 65L BrewZilla Gen 4 models with the smaller pump, you will need to perform some light electrical terminal rewiring. This pump comes fitted with blade and circle connectors to swap out the standard 6W pump. You will need to re-use the grommet fitting so be gentle when taking it off the 6W pump. Standard Configuration – No additional fittings/hoses required This configuration is a direct swap out of the 6w pump to the 25w pump. Utilizing the tee splitter and the original hosing that comes with the 65L Gen 4 BrewZilla. It does help a little bit if you use the outlet elbow piece on the inlet, and vice versa as the 25w pump is slightly taller than the 6w stock standard pump. Alternative Configuration – Oli's Hail Mary For this method you will need about 6.5" of 1/2" ID hosing, preferably braided silicone. You cannot use normal silicone hosing for this. This method does not use the tee piece or ball valve. It solely relies on the bigger 25W pump to do all of the transferring and recirculating needs. Please see product photos for configuration types. Specifications: Voltage: 220-240V at 50-60hz Max Head: 11.1 ft Max Flow: 5 gal Wiring: Fork and Ring Connectors fitted with insulation sheath Fittings: 1/2" (13 mm) barbs NOTE: Like almost all centrifugal pumps, do not run this pump dry. KegLand Part Number: KL25126
The Push-In Pressure Gauge comes with an 8 mm (5/16 in.) barb, specifically designed to be compatible with 8 mm Duotight fittings. The dial face is triple-scaled to read in psi, bar, and kPa.
8 mm (5/16") push-in barb
Rubber coated to protect gauge
0-150 psi / 0-10 bar / 0-1,000 kPa
Kegland Part number: KL07696
This heavy-duty mash paddle will rip through your mash tun like slicing through butter with a light saber! Drilled holes provide less resistance when breaking up dough balls. Tig welded and made from 304 stainless steel.
The paddle is 76cm (29.9") in total length with a paddle head measurement of 23cm x 14cm (9" x 5.5").
KegLand Part Number: KL03797
The most robust controller we offer and a perfect compliment to the technically savvy brewer. This is the only controller we offer that allows for up to 12 steps. This can be incredibly handy for raising fermentation temperatures for diacetyl rests and also for cold crashing. You can also use it with electric mashtuns and pumps to do step mashes. The high and low temp alarms are also handy, as is the ability to use with a distillation column.
Key features
Dual input for Control of heating and cooling devices simultaneously
Program up to 12 steps (unique to this controller) - which allows for advanced fermentation control and even mashtun control if you used for mash.
F or C
Can be used with electric distilling column
Adjustable differential
Adjustable differential between start of cooling and heating
High and low temperature alarms
Kegland Part number: KL01946
This handy part is what you need to connect one side into a standard 8 mm Duotight fitting and secure the other side with 1/4" ID tubing using a hose clamp over the tube. We have wide range of stainless stepless hose clamps that you can purchase here. KegLand Part Number: KL25935
Quickly check your fill volume when filling kegs with cold beverage
Sticker reacts to cold temperature, turning from yellow to green
Apply two stickers on 5-gallon kegs to run the full length of the keg
These keg filler stickers are designed to help you quickly check the fill volume, especially when filling cold beverages like cold-crashed beer. When the liquid inside is cold, the color changes from yellow to green. For 5-gallon kegs, you will need to apply 2 stickers if you want the gauge to run the full length of your keg.
Size: 8.85" x 0.47"
Color Warm: Yellow
Color Cold: Green
KegLand Part Number: KL42659
Comes with a back nut, plastic collar, hex nut, and 8 mm Duotight Adapter compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Requires a 1" hole saw for installation. When set in place, the shank will only have about 2 1/2" of length to pass through your wall or fridge door, due to the length of the collar and back nut. Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 5-1/8" - Total Length (Tip to Tip) 4" - Shank Length (Without Nut & Barb) 3" - Thread Length 2-1/2" - Pass Through Length Kegland Part number: KL11945
Made from HDPE this handy little bulkhead tap has a 3/8" OD barbed end. Got an old plastic bucket lying around? Drill a 24 mm hole, add one of these handy little numbers and hey presto! Instant fermenter!
Super easy to install and with a much more positive action that a typical little HDPE fermenter tap.
KegLand Part Number: KL20343
The Duotight Flow Stopper is a handy devicie to use while filling kegs or when transferring between kegs during filtering or after fining. Simply attach the Flow Stopper to the gas post of your keg, then when the keg is full it will automatically cut off flow and prevent excess beer from exiting your gas post and spilling onto the floor. For even better results, we recommend using the Flow Stopper with the BlowTie Spunding Valve. The BlowTie will enable you to apply head pressure to the keg, meaning you can control the flow speed and reduce the foam generated in the filling process. You will need a short length of 8 mm OD EVABarrier tubing to connect the BlowTie to the outlet of the Flow Stopper. Includes:
2 x Duotight 8 mm x 5/8" FPT (DUO104) 1 x Duotight 8 mm elbow (DUO107) 1 x Duotight 8 mm x 1/4 in. flare (DUO106) 1 x Ball float 1 x Stainless spring 2 x 8 mm OD EVABarrier joiners 1 x Acrylic sight glass Ball lock fitting and BlowTie spunding valve not included.
Kegland Part number: KL09393
The ultimate portable draft faucet! Compact & lightweight with all the advantages of a standard NukaTap forward sealing faucet
Includes NukaTap Mini, Flow Control Ball Lock QD, Duotight Adapter, and Self Closing Spring
Forward-sealing design prevents beer residue from gumming up the faucet
Reduced first pour foam due to low thermal mass and conductivity
Perfect for mobile draft, mini kegs, sampling from fermenters, and can even be installed on your kegerator or keezer
Mini Design – Ideal Flow Rate for Small Systems
Most conventional beer faucets are designed with 3/8" diameter spouts so you can pour a pint in just over 10 seconds. This type of flow rate is great for high turnover bars and commercial venues but isn't necessary or even desirable for all applications. For compact portable systems and home draft systems, a slower flow rate is easier to control and further reduces foaming issues due to the low liquid volume stored in the body of the faucet.
The NukaTap Mini is also more ideal for pouring smaller doses. For example, cocktails where 5-8 oz of liquid is dispensed is difficult to control with a high flow rate tap. For portable systems, the NukaTap Mini with the Flow Control Ball Lock QD & Duotight Adapter assembly is small enough to literally put in your pocket, making it ideal for mini keg setups that you want to be portable or that you want to easily fit inside a domestic fridge where space is tight.
Forward Sealing
Forward sealing faucets are absolutely the way to go when it comes to beer taps. Old legacy taps still exist in the industry that are simply poorly designed. The issue with rear sealing faucets is that beer dries up on the internal piston. Aside from being unsanitary, as more and more beer dries up in these components the faucet can almost glue completely shut causing damaged seals or broken handles (this is particularly the case if it's left for some time to dry out with beer inside). These older legacy designs still exist probably due to poor education. The forward sealing designs do not have this problem and the tap drains out completely with no beer drying up on the mechanical moving parts in the same way. This makes the tap more sanitary and reduces maintenance. In many instances the price is similar so there is no reason to use a poorly designed rear sealing faucet. All NukaTap faucets are forward sealing.
Laminar Flow
Just like the NukaTap SS and NukaTap FC, the NukaTap Mini has been designed with laminar flow in mind. Laminar flow is critical for a beer tap as it means you will pour the beer with minimal foaming and a substantial reduction in wastage. Think about how many times a beer faucet opens and closes in its lifetime. 1,000 or maybe 10,000 times? Laminar flow saves wasted beer in excessive foam and the better laminar flow easily pays for itself in a reduction in lost beer. To use poorer designed faucets is essentially flushing money down the sink. Extensive modeling has been done on the NukaTap design to improve laminar flow.
Integrated Seals That Are Indestructible and More Sanitary
Unlike other designs, the NukaTap Mini body is made from Polyketone (POK) making it strong, robust, and able to be autoclaved. The seals are also over-molded from Santoprene® making them hard wearing so they will literally last for the lifetime of the tap without the need for replacement. Santoprene® and POK both have excellent resistance to chemicals such as caustic soda, peroxide, phosphoric acid, lactic acid, citric acid, acetic acid, and all common chemicals sold and used in the beverage industry. The seals internally are over-molded meaning no fissures or cracks exist for bacteria, crud, or yeast to hide.
Superior First Pour Foam Due to Low Thermal Mass and Conductivity
First pour foam is an issue caused by a warm tap body. For most faucets to pour well it's important to dispense enough beer to cool the tap body down to reach maximum performance. In addition to this the conductivity of the tab body also makes this worse so insulative materials simply work better than conductive materials. The NukaTap mini not only has very low thermal mass but is also highly insulative being made mostly from Santoprene® and POK. The combination of these two factors in conjunction with superior laminar flow makes for the lowest "first pour foam" effect out of any tap ever produced.
Long Shank Alternative
Most conventional beer faucets require a large 3/4" hole to be drilled through the side of your refrigerator, keezer, or cold box wall. Traditional long shanks also generally have a large volume of liquid that sits inside the wall unrefrigerated which is not ideal. New long shank alternatives developed for the NukaTap Mini are designed to suit any wall thickness and greatly reduces the stagnant beer sitting in the shank itself. For walls up to 2.7" thick, these wall mount shank kits include three screws, however if the wall is thicker, you can also use 6 small wood screws or something similar and attach three screws from the front and 3 from the back allowing you to go into any wall type.
Another advantage of this new design is the tap will never accidentally rotate. Typically, other long shank beer taps rely on the hex nut on the shank to be done up tight enough to prevent rotation but if the wall compresses (often the case with foam walls) the tap is allowed to rotate. This new design has three fixing points making it impossible for the tap to rotate accidentally as the interlocking teeth behind the collet allow you to set the angle and then do up the collet to fix the tap permanently in that position.
Use this lid along with the 35L BrewZilla or DigiBoil and a copper still top (DS120or DS130) to make your own easy-to-use distillery. This lid has a 1.85" (47mm) hole for the still top. Lid gasket included. Note: This lid uses a 6mm gasket to better fit the Gen 4 BrewZilla and Gen 2 DigiBoil. It is also backwards compatible with Gen 3 and older BrewZillas and Gen 1 DigiBoils. To improve the seal further, we highly recommend using the Adjustable Lid Clamps with the Distillation Lid if your unit does not have them. Made from 304 stainless steel Measures 12.25" in diameter. Kegland Part number: KL03483
This Duotight fitting with 1/4" Flare is perfect for flared gas ball lock and pin lock disconnects. Can also be used to connect gas line to the flare fitting found on the KOMOS® CO2 Regulator. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Although this fitting would also fit a beverage disconnect, 9.5 mm OD EVABarrier is only recommended for beverage line in long draw draft set ups. The Duotight fitting does not require a flare washer. See the instructions below for how to ensure a leak-free connection when attaching to flare fittings. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL11037
Ready to dive into distilling, but unsure how to piece together your home still? Check out these complete systems that will set you on the path to producing high quality spirits. This kit comes with the 35L DigiBoil Electric Kettle and the Copper Pot Still Condenser.
The Copper Pot Still is perfect when you want the flavor of the wash to come through, whereas a reflux still is more favorable for producing pure, unflavored spirits. If you want to make whiskeys and gins, this pot still top is a great way to start! The classic "V" shape captures the vital esters, aldehydes, and phenolic compounds that are necessary for the complex spirits such as whiskeys and gins. Made from solid copper. When your hot spirit comes into contact with the copper, the copper acts like a catalytic converter to drive sulfur out of the spirit. This leads to less off-flavors and higher quality spirit.
Kit Includes:
35L DigiBoil Gen 2 (110V or 220V)
110V / 15A power and plug (5 ft. cord)
220V / 15A power
NEMA 6-15 plug (5 ft. cord)
Copper Reflux Still Condenser w/ Barb Connections
13 mm Inlet/Outlet Barbs (0.51 in.)
Distillation Lid & Gasket
Set of Adjustable Lid Clamps
Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States. It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA).
Want an easy-to-use, stainless vessel that ferments and carbonates? This 50L/13.2 Gallon keg has been modified to allow you to do both! The top is fitted with a large 4 inch tri-clamp lid with two ball lock posts and a pressure relief valve. You can use this vessel to ferment, carbonate, serve, or push the beer through a filter. The posts are recessed which allows you to stack these kegs up to 4 high. A 4" T.C. end cap with pre drilled hole is also available (H691), which can be paired with a #3 stopper and airlock. Also consider the Kegmenter Hop Bong Pressure Pack which allows for oxygen-free dry hopping and also features ball lock posts for Gas & Liquid. Depending on how long it will take to consume the finished beer, we recommend using two kegmenters, one for fermentation and one for carbonating and serving. After fermentation, there will be a large trub cake at the bottom of the vessel. Leaving finished beer on the trub for too long (2-3 weeks) may eventually lead to off-flavors. Check out our ball lock jumper line (KEG575) to easily transfer from one kegmenter to the other. Also consider our beer filter kit (FIL40), which will allow you to filter the beer during transfer. Features: Rated up to 2.5 BAR (36 psi) 4" T.C. lid with ball lock posts Floating dip tube Stainless steel 1.8 mm thick Use: As a stainless steel fermenter that is easy to clean Great choice for 10 gallon fermentations Easy to pressurize the kegmenter after fermentation to push through a filter and into another keg Fermenting under pressure, allowing CO2 to exit via the relief valve, reduces esters and fusel alcohol production allowing you to ferment at warmer temperatures Distillation - with the addition of a T.C. reducer and condenser (H701 / DS120 / DS130) As a cellar keg for topping up barrels Warning: Always depressurize keg before removing lid. Does not come with spunding valve show in example photo. See FIL42A. Kegland Part number: KL04565
These cartridges give the oomph to your mini-regulator dispensing unit! Perfect for dispensing your beer on the go. One canister will push between 1-4 Cornelius kegs, depending on how it is used and the CO2 consumption required. With the 74g adapter piece, these cartridges can be used with the KegLand Core 360 Mini Regulator or Torpedo Mini CO2 Regulator. 5/8-18 UNF threading Kegland Part Number: KL16889 Please note: due to air shipping restrictions, this product is only eligible for ground shipment within the contiguous United States.
Take temperature readings instantly and from a safe distance with this infrared thermometer gun. Use it to check how close you are to the hot break before your boil, or measure the temp of your empty mash tun and grains to help predict temperature loss when you add strike water and mash in. Dual lasers is an important feature when choosing infrared thermometers because it allows for much higher accuracy. When measuring an object, a dual laser thermometer gun will help you greatly in finding the convergence point of the measured target and spot ratio. This can only be achieved with a dual laser unit.
Features:
Double Laser pointer for higher accuracy
Simple one-handed operation
Laser ON/OFF switch
Low battery indication
LED backlight
Reads in °F / °C
Automatic shutdown after 15 seconds
Display hold, Scan function
FCC, CE, ROHS Certified
Notes:
1. When using this product to measure temperature, consider the ratio between the distance (the length from the product to the measured object) and the size of the measurement area, referred to as the object distance ratio. When the distance between the product and the measured object increases, the measurement area will increase accordingly.
2. If you want to use boiled water to measure the unit's accuracy, do not allow smoke or water vapor to contact the temperature sensing area, and keep the measurement angle at 45 ~ 60 degrees.
KegLand Item Number: KL21883
Oxygen-Free Dry Hopping: Designed to allow dry hopping without exposing the batch to oxygen when used in combination with the 2" Hop Bong, 2" Butterfly Valve and additional accessories. Customizable with Accessories: Features undrilled ports for optional accessories such as the Temp Twister Cooling Coil and Thermowell, enhancing functionality and convenience. Improved WiFi Reading: The plastic lid improves KegLand RAPT Pill WiFi reading, ensuring better connectivity. Durable and Pressure-Resistant: Includes 4" and 2" Tri-Clamp ferrules, suitable for use up to 21 psi, with recommended PRV options for safe operation at specified pressures. Compatible with all Kegmenter Fermentation Kegs with 4" Tri-Clamp ferrule. See the Kegmenter Hop Bong Pressure Pack for a complete kit option. Upgrade your Kegmenter Fermentation Keg with this 4" Tri-Clamp Lid from KegLand. Add yeast, hops or even take samples from a wine thief from the top and not have to remove the entire lid. This particular lid was designed to address the growing desire to dry hop without exposing the batch to oxygen from opening the lid. By using this lid in conjunction with the FermZilla 2" Butterfly Valve and Hop Bong Kit, you will be able to purge CO2 into the tube and expel all the oxygen inside it and dump freely into the vessel. The lid features closed ports that can be drilled out to install optional accessories like the Temp Twister Cooling Coil and a Thermowell. The plastic lid also allows for improved KegLand RAPT Pill WiFi reading compared to the Kegmenter fully encasing the Pill in stainless steel. Due to the large 4" Tri-Clamp diameter, it is difficult to get higher pressures without leaking, therefore we suggest using the lid up to 21 psi. If you do not already own any of the Hop Bong fittings listed below, the Kegmenter Hop Bong Pressure Pack is also available as a complete kit. Features: (2) PCO1881 Male Ports Recommended for use with Red (Gas In) & Yellow (Bev Out) Ball Lock Caps PRV Port This should only be used with a Red 35 psi PRV or the Yellow 17 psi PRV. 2" T.C. Ferrule 4" T.C. Ferrule Undrilled Ports (for optional accessories): Thermowell Port (see below for FermZilla Thermowell kit) (2) Temp Twister Ports Please Note: Temp Twister will need to be bent on a 20° Angle in order to fit on the curved lid and align vertically in the tank. Hop Bong To use the Pressure Lid with the 2" Hop Bong, we recommend the following fittings if you do not have them already: 2 x Red Ball Lock Cap (FE13) 1 x Yellow Ball Lock Cap (FE146) 1 x 4" Tri-Clamp, 3 Segment Clamp (H734) 1 x 4" Tri-Clamp Seal (FF401) 3 x 2" Tri-Clamp (FF20) 3 x 2" Tri-Clamp Seal (FF201) 1 x 2" Butterfly Valve (FE198) 1 x 2" Hop Bong (FE202) 1 x 2" Hop Bong Cap (FE204) 1 x PCO1881 PRV Cap (KG523) 1 x Red 35 psi PRV (FE101C) Please note: The last product photo is an example image of what the lid looks like fully fitted out with the Hop Bong and other accessories that are not included with the lid.
Compatible with the 27L and 55L FermZilla Tri-Conical Series or any 3" T.C. fittings. This can be used on the bottom of your conical for a maximized dump valve or it can be used with a FermZilla T.C. Pressure Lid with 2" x 3" reducer and sight glass to make a massive hop injector.
KegLand Part Number: KL27571
This Graduated Cylinder is made from the same laboratory borosilicate glass as our Erlenmeyer Flasks. They have a volume of 250 mL with 2 mL graduations for accurate measurements.
Perfect for hydrometers / alcometers and testing the clarity of your beverage.
KegLand Part Number: KL04046
The Copper Reflux Still Condenser is designed to create high percentage pure neutral spirit. It features a flow management device, which makes it extremely easy to use. No need to worry about fine tuning the water flow speed. As long as your providing enough coolant or cold water running through the condenser, the flow rate doesn't matter. The purity of the spirit can be controlled by two included flow control inserts. These brass inserts come with a 1.0mm hole and 0.6mm hole. As the hole gets smaller, the rate at which the spirit exits the condenser will decrease, thus increasing your reflux ratio and the purity of your spirit. If you want to make whiskeys and gins we recommend checking out the Copper Pot Still! This is only the still top and does not come with a boiler. Combine with a distillation lid to use a BrewZilla or DigiBoil as the base for this Alcoengine brand still top. Comes with 13 mm (0.51") barb connections for the water inlet and outlet. Kegland Part number: KL16162
This premium Polypropylene Base Board is for the MaltZilla Motorized Grain Mill. Perfect for slotting over a food grade bucket, or building your own little shelf on wheels.
Board Dimensions - 17.75" x 13.5" x 3/8"
Kegland Part Number: KL17077
It is really THAT easy to make good beer at home?+
YES! If you can follow a recipe and keep clean, there is nothing stopping you from making great beer in your home - beer you can be proud of and your friends will love! The MoreBeer! mission is to provide reliable equipment and quality ingredients that make the home brewing experience successful and satisfying. We'll get you started in home brewing the way we wish we had been started.
