Sometimes a single draft tower isn't enough for your dream home bar or kegerator. If you're building out a draft system that will have more than four faucets, we highly recommend the KOMOS Double T Bar Draft Tower. Available in 6-tap and 8-tap models, these towers provide ample room for your faucets and will give your draft setup a much cleaner look than having multiple single-column towers. Perfect for upgrading an existing KOMOS Double-Wide Kegerator with two individual towers or designing your own home bar or kegerator.
Mounting hardware, tower collars and gaskets included. The tower does not include faucets, shanks, tap handles, or draft tubing.
Assembly
To assemble the tower, remove the dust caps on either side and remove the foam insulation. Start with the inner most shank hole on either side and work your way outward. We recommend installing each shank and attaching the draft tubing before moving on to the next shank hole. The top section of the tower is 5" in diameter, so most people should be able to reach inside to install the shanks by hand or with the help of a draft wrench. When all the shanks have been mounted, reinsert the foam insulation. The tower may come with more insulation than needed and may need to be cut thinner before reinserting.
We recommend using the Double Offset Shank Wrench to help with assembly.
Duotight Compatible Tower Shanks
We highly recommend pairing the draft tower with Intertap Tower Shanks with Duotight Compatible Barb. When it comes to assembly, there's nothing easier than Duotight push-to-connect fittings, and the same goes for whenever you might need to disassemble a line for cleaning. Duotight fittings pair perfectly with EVABarrier draft tubing, our preferred beer & gas tubing that offers superior protection from oxidation, CO2 loss, and microbial growth.
Tower Dimensions: 29.5" L x 5" D x 16" H. The centers of the columns are approximately 16" apart.
Not compatible with the KOMOS Olympus III kegerator.
Sometimes a single draft tower isn't enough for your dream home bar or kegerator. If you're building out a draft system that will have more than four faucets, we highly recommend the KOMOS Double T Bar Draft Tower. Available in 6-tap and 8-tap models, these towers provide ample room for your faucets and will give your draft setup a much cleaner look than having multiple single-column towers. Perfect for upgrading an existing KOMOS Double-Wide Kegerator with two individual towers or designing your own home bar or kegerator.
Mounting hardware, tower collars and gaskets included. The tower does not include faucets, shanks, tap handles, or draft tubing.
Assembly
To assemble the tower, remove the dust caps on either side and remove the foam insulation. Start with the inner most shank hole on either side and work your way outward. We recommend installing each shank and attaching the draft tubing before moving on to the next shank hole. The top section of the tower is 5" in diameter, so most people should be able to reach inside to install the shanks by hand or with the help of a draft wrench. When all the shanks have been mounted, reinsert the foam insulation. The tower may come with more insulation than needed and may need to be cut thinner before reinserting.
We recommend using the Double Offset Shank Wrench to help with assembly.
Duotight Compatible Tower Shanks
We highly recommend pairing the draft tower with Intertap Tower Shanks with Duotight Compatible Barb. When it comes to assembly, there's nothing easier than Duotight push-to-connect fittings, and the same goes for whenever you might need to disassemble a line for cleaning. Duotight fittings pair perfectly with EVABarrier draft tubing, our preferred beer & gas tubing that offers superior protection from oxidation, CO2 loss, and microbial growth.
Tower Dimensions: 29.5" L x 5" D x 16" H. The centers of the columns are approximately 16" apart.
Not compatible with the KOMOS Olympus III kegerator.
Jazz up your kegerator, home bar or commercial beverage dispensary with these stylish decal holders. Clamps directly on to the beer shank coupling nut so you don't have to remove the faucet to put on the decal holder or to swap out the decal itself. Made from chrome plated plastic with a soft padding to protect your draft components from scratches. Easily attach or remove the decal holder with a philips head screw dirver.
This unit will fit an 82 mm (3.2") diameter decal, sticker or label. Also avaialbe in 73 mm (2.8") diameter.
KegLand Part Number: KL00888
Get your KOMOS Jockey Box hooked up and ready to flow with our preconfigured connection kits! This connection kit includes everything necessary to hook up four American "D-Style" Sanke kegs to your KOMOS Jockey Box except for the CO2 tank and regulator. Choose the connection kit that matches the number of taps you require and the type of keg being served, add on a regulator or CO2 tank if you do not already own one, and get ready to pour flawless pints!
KOMOS 4 Tap Sanke Keg Connection Kit includes:
5 x 5 ft. lengths of 5/16" CO2 Tubing
4 x American Sankey "D" Couplers
4 x 5 ft. Beverage Jumpers with Stainless Steel Tailpieces
Four-Way Aluminum Air Manifold
Hose Clamps and Rubber Washers
This Kit Does Not Include a CO2 Tank or Regulator, but both can be added from the drop-down menus above or under "You Might Also Need" below.
This Friction Bonnet is the piece that sits between the body of the faucet and the faucet knob lever Collar. Tightening it compresses a washer and creates resistance when opening and closing the faucet.
Fits all Intertap and Nukatap faucet models.
Get your KOMOS Jockey Box hooked up and ready to flow with our preconfigured connection kits! This connection kit includes everything necessary to hook up two American "D-Style" Sanke kegs to your KOMOS Jockey Box except for the CO2 tank and regulator. Choose the connection kit that matches the number of taps you require and the type of keg being served, add on a regulator or CO2 tank if you do not already own one, and get ready to pour flawless pints!
KOMOS Dual Tap Sanke Keg Connection Kit includes:
3 x 5 ft. lengths of 5/16" CO2 Tubing
2 x American Sankey "D" Couplers
2 x 5 ft. Beverage Jumpers with Stainless Steel Tailpieces
Two-Way Aluminum Air Manifold
Hose Clamps and Rubber Washers
This Kit Does Not Include a CO2 Tank or Regulator, but both can be added from the drop-down menus above or under "You Might Also Need" below.
U-Type keg coupler for Guinness and some other Euorpean beer kegs
Stainless steel keg probe and coupler body
Pull-style lever handle
Includes 3/8" OD barb for gas inlet
A special tap that is required for Guinness kegs. U-Type Tap. Also known as a keg coupler, coupling, or adapter.
Will Usually Fit:
Abby White
Boddingtons Pub Ale
Guinness Stout
Harp
Kilkenny
Leffe
Magners
Smithwicks Ale
Rinse and chill your glassware before every pour!
Install on the countertop of your wet bar or kitchen sink and hook up to your home water supply
Invert and push down your glassware to activate the spray action
Excellent kitchen accessory for rinsing wine glasses, compact blenders, tumblers, and More!
A push activated glass rinser can be the perfect final touch to your wet bar for the serious home beertender. Install at the edge of your sink and connect to your household's main water supply. Push down in short bursts to rinse your glass of dust, residual dish soap, and to pre-chill the glass before pouring a pint. These compact glass rinsers are capable of withstanding up to 100 psi of pressure. The 1/2" BSP threaded rod is compatible with a number of Duotight attachments. We recommend installing with PE Water Line and this 1/2" adapter.
How to Use:
Invert glass and empty last drips into sink
Press glass onto the center of the glass rinser in short bursts
If you have access to an inline carbonated water source, using bubbly water will really give your glasses a stripping clean. This device can also be used with chilled water to cool your glass down in between beverages.
4.3" H x 4.5" W
KegLand Part Number: KL27649
Handles both dispensing and rapid burst carbonation, ideal for seltzers and high-carbonation drinks requiring 30-40 psi
Includes both Duotight and barb fittings for use with EVABarrier tubing or standard gas tubing
Features a shutoff valve for safe operation and standard US CO2 tank threads (CGA320)
Rubber gauge protectors safeguard gauges from potential damage
Compatible with standard US CO2 tanks
The KOMOS Dual Gauge Precision Universal Regulator is suitable for both dispensing and carbonating beverages. Compared to the Precision Dispensing model, the Universal model features a wider 0-50 psi operating range, enabling pressures above 25 psi for rapid burst carbonation. This is particularly useful for seltzer and other highly carbonated drinks requiring 30-40 psi dispensing pressure.
The regulator includes both Duotight and barb fittings for compatibility with EVABarrier draft tubing and standard gas tubing. The gas outlet features a shutoff valve for safe and convenient operation. Rubber gauge protectors are also included to safeguard the gauges from potential damage.
Features:
0-50 PSI operating range
Low pressure gauge reads from 0-60 psi
Pull ring PRV rated to blow off at 50 psi
Narrow pressure range for increased precision
1/4" & 5/16" barb fittings included
Duotight adapter for EVABarrier tubing included
Standard US CO2 Threads (CGA320)
Shutoff valve
Gauge protectors
Ideal for dispensing or carbonating beverages
Perfect for mobile draft dispensing with the NukaTap Mini Beer Faucet
Clamp onto a picnic bench or folding table—an ideal option for backyard cookouts or concerts in the park
Makes for a great temporary shank for weekend getaways, camping, or tailgating
This bracket is compatible with table or bench edges that are up to 3.5" thick. It can be adjusted to have the wing nut clamp in either direction, simply unscrew the flange piece from the threaded rod, then unscrew, then thread from the opposing side.
Please note: This item does not include the Mini NukaTap or Shank pieces. It is simply the stainless steel bracket.
Recommended Accessories:
NukaTap Mini Faucet (D1598)
Wall Mount Shank Kit w/ 6.35 mm Duotight (D1598D)
Self Closing Spring (D1598A)
6.35 mm OD EVABarrier Tubing (D1723C)
KegLand Part Number: KL04077
Portable, Inline, Keg Dispensing unit that can be powered via 110V outlet
Replaces a traditional Draft Box/Jockey Box with no ice required
Differs from the regular Komos Kryo Inline Chiller in that there is no glycol reservoir / The Nomad is liquid-free and easier to transport
Can chill up to 2 gallons of room temperature beer, inline, per hour
NukaTap Flow Control Faucets, tap handles, and drip tray included
Mobile draft dispensing has never been easier with the KRYO Nomad electric keg dispenser. As with a jockey box, beer is chilled inline as it passes from the keg through the internal draft coils which are chilled by the electrically powered solid carbon based heat sink. With a standard 110V outlet, you can serve ice cold beers from an unchilled keg, and unlike the KRYO glycol unit, this model is absolutely liquid-free, making it the ideal choice for mobile draft dispensing. No need to wait an hour for glycol solution to chill, once you power on the Nomad, you'll be ready to go in as little as 15 minutes!
Carbon Heat Sink
The secret to the KRYO Nomad's incredible chilling capacity and portability is the solid carbon based heat sink. This heat exchange technology requires no liquid whatsoever, so you'll never run into issues with emptying or spilling coolant when you transport this chiller from place to place. It provides roughly 300 watts of cooling power which allows you to chill about 2 gallons of beer per hour. Just be sure to give the unit about 2 minutes to recover for each 16 oz pour. The Nomad is very power efficient, drawing only 60 watts of power when the compressor is running. When idling, the chiller uses only 1.6 watts of power, meaning it it averages only 15 watts of power draw when turned on and periodically cycling the compressor.
NukaTap Flow Control Faucets
These stainless steel forward sealing faucets allow you to make instant adjustments to the beverage flow as you pour. A perfect faucet for those who often switch between beer styles with different carbonation levels. No need to rebalance your lines or play with your regulator settings. Adjust the flow control level to dial in the flow rate and pour perfect pints every time! They also have the lowest thermal mass and best laminar flow design to further reduce foaming issues.
Duotight Bulkheads
Draft lines connect directly to 8 mm Duotight bulkheads located at the rear of the unit. To hook up your kegs to the KRYO Nomad, we highly recommend EVABarrier draft line and Duotight fittings—the same lines and fittings that come standard with our KOMOS Kegerators. 8 mm OD EVABarrier plugs directly into the bulkheads, then depending on what type of kegs you'll be pouring, you can use these Duotight Female Beer Thread Adapters for sanke keg couplers if you'll be dispensing commercial kegs, or for homebrew kegs, we recommend Duotight Flare Adapters for your QDs, or if you're starting from scratch, consider the Duotight Ball Lock Quick Disconnects.
Includes:
(2) NukaTap Stainless Flow Control Faucets
(2) Tap Handles
Stainless Countertop Drip Tray w/ Removable Grill
Features:
Chill 2 gallons of beer per hour (based on 68°F ambient)
Duotight bulkheads compatible with 8 mm OD EVABarrier tubing
AC Voltage via IEC Plug: 110-120V
Max Power Draw: 300W
Dimensions: 9.25" x 13.7" x 18.1" (not including faucets / drip tray)
CE Certified
Temp Controller:
Follow these steps to adjust the SET temperature on the controller.
Press and release the 'SET' button to enter into the user menu.
Press 'SET' will display the value of the target temperature setting.
Press the 'Up' or 'Down' button to increase or decrease the set temperature.
Press the snowflake icon button or wait 30 seconds and the controller will save the setting and return to normal operation mode.
Warning: Do not set the temperature controller lower than 28°F (-2ºC). Running the unit below this temperature may negatively affect the unit's efficiency and has the potential to freeze beer which may impact the finished beer's flavor.
Perfect for mobile draft dispensing with the NukaTap Mini Beer Faucet
Clamp onto a cooler to make a jockey box without needing to drill out shank holes
Makes for a great temporary shank option for kegerators and keezers when you need an extra tap
This bracket is compatible with ice chest coolers and fridges that are up to 3.5" thick. It can be adjusted to have the wing nut clamp in either direction, simply unscrew the flange piece from the threaded rod, then unscrew, then thread from the opposing side.
Please note: This item does not include the Mini NukaTap or Shank pieces. It is simply the stainless steel bracket.
Recommended Accessories:
NukaTap Mini Faucet (D1598)
Wall Mount Shank Kit w/ 6.35 mm Duotight (D1598D)
Self Closing Spring (D1598A)
6.35 mm OD EVABarrier Tubing (D1723C)
KegLand Part Number: KL22002
Counter top inline keg dispenser that can serve ice cold beer from unchilled kegs
Compact and portable. Use anywhere you have access to 110V power
Superior cooling capacity. Chill up to 8 gallons of beer, inline, per hour!
Fill the reservoir with tap water, or use a glycol solution for optimal performance
NukaTap Flow Control Faucets, tap handles, and drip tray included
Great for bars, restaurants that need to add capacity
These style chillers are how beer is poured in most European cafes
If you're looking for a home draft system, but don't have the space for a kegerator or keezer, we've got the answer! The KOMOS KRYO benchtop keg dispenser can serve ice cold beer from unchilled kegs. It's essentially an electric jockey box that chills beer inline as it passes from the keg through the internal draft coils that sit submerged in the glycol reservoir. Simply place it on your counter or benchtop, fill the reservoir with a 20% glycol solution, and hook up your keg to the draft shank bulkheads. In roughly an hour, the reservoir will have cooled down enough that you'll be ready to pour! And thanks to the compact size, the KRYO can easily be transported from your home to the next backyard BBQ, cabin trip, wedding, or virtually any gathering of thirsty people you can think of. For homebrewers this would allow you to keep your refrigerator at fermenation temperatures while always seving your beer ice cold.
Glycol Reservoir
Although you can fill the reservoir with water only, for optimal performance we highly recommend using a glycol/water mix so you can lower the chilling solution below freezing. You simply won't be able to get your beer as cold if using water only. The sight gauge at the front will let you know if it's time to top up the reservoir, but also functions as a drain. When it's time to move the KRYO from one location to another, drain out the glycol into a sealable container to avoid spills during transportation.
The glycol reservoir provides an exceptional amount of cooling power that makes it perfect for servicing small bars or cafes, as well as home use. If you're deciding between this model and the KRYO Nomad, note that peak chilling capacity for this model is approximately 8 gallons per hour, whereas the Nomad can chill up to roughly 2 gallons per hour.
NukaTap Flow Control Faucets
These stainless steel forward sealing faucets allow you to make instant adjustments to the beverage flow as you pour. A perfect faucet for those who often switch between beer styles with different carbonation levels. No need to rebalance your lines or play with your regulator settings. Adjust the flow control level to dial in the flow rate and pour perfect pints every time! They also have the lowest thermal mass and best laminar flow design to further reduce foaming issues.
Draft Shank Bulkheads
The draft shank bulkheads with beer thread allow you to choose the type of fittings and draft line that best suits your needs. We highly recommend EVABarrier draft line and Duotight fittings—the same lines and fittings that come standard with our KOMOS Kegerators. These Duotight Female Beer Thread Adapters will allow you to hook up 8 mm OD EVABarrier, and also work with sanke keg couplers if you'll be dispensing commercial kegs. For homebrew kegs, we recommend Duotight Flare Adapters for your QDs, or if you're starting from scratch, consider the Duotight Ball Lock Quick Disconnects.
Includes:
(2) NukaTap Stainless Flow Control Faucets
(2) Tap Handles
Stainless Countertop Drip Tray w/ Removable Grill
Features:
Chill 8 gallons of beer per hour (based on 68°F ambient)
Draft shank bulkheads compatible with Duotight fittings or nut & tailpiece combos
STC-1000 temperature controller (reads in °C)
Reservoir volume: 4.2 gal
Voltage: 110V-120V
Current: 0.9A
Frequency: 60Hz
Dimensions: 19" x 12" x 17.5" (not including faucets / drip tray)
CE Certified
Reservoir Temp Controller:
Follow these steps to adjust the SET temperature on the controller. If using water only, be sure to keep the reservoir temp set at or above 2°C to avoid freezing. With a 20% glycol solution, you can set the temp as low as -2°C. The reservoir volume is 4.2 gallons, so you will only need to purchase 1 gallon of glycol to make a 20% mix.
Hold the 'Up" button for 3 seconds until the number is flashing
While the number is flashing, press the 'Down' button to decrease the set temperature or press the 'Up' button to increase the set temperature.
Wait 3 seconds and the controller will save the setting and return to normal operation mode.
Warning: Do not set the reservoir temperature controller lower than 28°F (-2ºC). Running the unit below this temperature may negatively affect the unit's efficiency and has the potential to freeze beer.
An adjustable pressure relieve valve with a range from 0 to 30 psi. Made from stainless steel this is non-threaded and designed to be welded in place.
For a 1/4" MPT option see D1833L.
The V10 stainless steel flow control faucet is designed and produced in Germany with some assembly completed in the United States. This faucet contains technology such as the "Closed Piston Chamber with Encapsulated Compression Spring" that allows for a perfect forward seal on the faucet, no beer trapped in dead space to cause the lever to stick, and the ability to push the faucet backwards for an extra creamy head. The compensator itself has an extra long cone for a wider range of compensation and designed to eliminate uncontrolled shifting of the compensator cone. This configuration features a black standard faucet knob, a polished stainless steel faucet lever, and a lever flow control adjustment system.
Please note: The CM Becker X1 and V10 flow control faucets require a proprietary draft shank and will not work with a standard draft shank. Please select on of the draft shanks below to add to your order.
2.5" Chrome Exterior w/ Food Grade Liner (D12907)
2.5" Stainless Steel (D12908)
5-3/8" Stainless Steel (D12909)
Features:
Full length European Flow Control (completely control restriction at the faucet;no restriction line needed)
Made in Germany and assembled in the USA!
Features a built in “Creamer” function so you can put a fine cream head on your beer
Used in restaurants and bars locally and abroad
The faucet handle and draft shank in the example photo are not included.
How frustrating is it when hops cause blockage in your poppet, tap, ball valves and practically everywhere else? This really handy little filter can be used on with the Torpedo Keg Buoy or the floating dip tubes included with the Kegmenter and FermZilla Pressure Kit to prevent hops or other solids from getting sucked into the dip tube itself. The 304 stainless 80 mesh is fine enough to filter out hops and many other solids but not so fine that it gets blocked up easily. If you have a FermZilla or stainless Kegmenter this add is a must.
Made from HDPE and 304 Grade stainless steel, this product can be boiled or sanitized in the full range of cleaners that we sell. The plastic HDPE is over molded onto the stainless mesh to make a seamless finish. The end cap can easily pop off for cleaning.
Kegland Part Number: KL16957
Dual headed can filler compatible with carbonated and still beverages
Programmable fill height accurate to +/- 1mm for consistent fills with every operation
Timed CO2 purging takes place automatically to remove oxygen before each fill
The only filler model in this price range that can be set on a table and includes a drip tray
Hardware included to mount the filler to your wall if preferred
Set up takes only a few minutes with a simple push-button programming interface
Adjustable height—designed to fill cans of any size up to 32 oz Crowlers
Stainless steel construction throughout with self-draining drip tray
Just like the two-headed dog of Greek mythology, Orthos, this dual-headed can filler will perform like a beast in your canning line, doubling your fill rate and taking the stress out of canning day.
Operation
Programming the fill height and CO2 purge time is quick & easy and only requires pushing a single button to program your settings on either fill head. Once your settings are locked in, the LED ring will give you the green light to procced and filling and purging will execute automatically with a single push of the button. The Orthos Dual Head Can Filler utilizes an aero-grade pressure sensor to measure the height of the fill and is accurate to +/- 1mm for remarkably consistent fills each and every time.
Construction
We have designed the Orthos Filler to be a showcase for your taproom or home brewery, featuring a heavy stainless steel case and the necessary hardware for wall mounting or table use. The Orthos can be easily adjusted to fill any size can up to 32 oz Crowlers, and if need be, you can have two different style cans filling at the same time. The drip tray will help catch any potential spills throughout the filling process and features a drain that can be routed to a collection bucket or floor drain.
Cleaning
The cleaning process is just as easy as the filling process! Just attach a keg of water or beer line cleaner and run a fill cycle to clean out the product from the machine. The beer flows seamlessly through pinch valves, eliminating any internal cavities that need to be cleaned. The drip tray is conveniently removable for a quick wash after each use. When it's time for maintenance, simply swap out the beer tubing!
Includes:
Fittings / tubing to connect to 8mm Duotight inputs
(1) 8mm Duotight Tee Fitting (DUO1090)
(3) 8mm Duotight Elbow Fitting (DUO128)
(3) 5.5 ft. Length of 8mm OD EVABarrier Tubing (D1717A)
Duotight In-line Regulator (D1047)
Wall Mount & Feet
Drip tray
You May Also Need:
A keg of beer and connections for sanke or ball lock
Sanke: (2) 8mm Duotight Beer Thread Adapters (DUO104)
Ball Lock: 8mm Gas In & Bev Out Duotight Ball Lock QDs (DUO150 / DUO151)
8mm OD EVABarrier Tubing (D1717)
Dual Body CO2 Regulator (D1083)
OR
(2) Single Body CO2 Regulators (D1077)
Two pressure settings are needed. One to set the fill speed and the other to set the purge speed
Exceeding 3 PSI makes the purge turbulent and will mix air back into your can
We recommend KOMOS Regulators which include 8mm Duotight adapters for the output
Features:
Dual heads to fill two cans simultaneously
Stainless steel case
Consistent Fills
Drip tray, wall mount, & feet included
High fill accuracy
Easy programming
Fills still or carbonated products
Timed purging
Beer and CO2 inputs are 8mm Duotight
Specs:
Wall Mounted: 14-3/4" H x 7-7/8" W x 3" D
Table Mounted:
12 oz can: 15-3/4" H
32 oz Crowler: 17-3/4" H
7-7/8" W x 8" D
18V Power Supply
Stand-Up Design: The bladder's thick, rigid material allows it to stand upright, making it easy to fill with your favorite drinks and dispense them effortlessly
Keeps Beverages Fresh: A durable, multilayer film with an oxygen-blocking foil layer and a PE interior prevents oxidation and moisture loss, preserving the freshness and flavor of your beverages
Versatile for Many Drinks: The KegLand bladder is designed to hold a variety of non-carbonated beverages, from wine and spirits to coffee and cocktails, offering a simple solution for serving any of your favorite drinks
Serve your favorite non-carbonated drinks effortlessly with the KegLand 5L Stand Up Bladder. This versatile bladder is perfect for dispensing a wide range of beverages, including:
Wine
Spirits and Liqueurs
Coffee
Non-carbonated cocktails
This bladder is made from a durable, multilayer film. The interior layer of PE and an exterior foil (Mylar) layer work together to completely block oxygen and prevent moisture loss, keeping your drinks fresh. The material is also thick and rigid, allowing the bladder to stand upright on its own for easy filling and dispensing.
Please Note: This product is not suitable for beverages with an alcohol by volume (ABV) higher than 22%. A different, higher-density PE internal liner is required for higher ABV products.
KegLand Part Number: KL41287
1/4" tailpieces are ideally used with 3/16" draft line for a tight fit. If you'd prefer to use a different size tubing, the KOMOS S-style coupler for European kegs can also be purchased bare so you can mix and match your preferred tailpiece sizes.
The check valves will need to be installed before first use. The silicone check valve is inserted on the side gas-in port and the check ball and ball retainer are inserted on the top bev-out port.
S-style sanke coupler
Stainless body
Stainless probe
PRV rated to 4.5 BAR (65 psi)
This is a proprietary draft shank only intended for use with CM Becker X1 and V10 flow control faucets. It will not work with generic or other brands of faucets.
Jazz up your kegerator, home bar or commercial beverage dispensary with these stylish decal holders. Clamps directly on to the beer shank coupling nut so you don't have to remove the faucet to put on the decal holder or to swap out the decal itself. Made from chrome plated plastic with a soft padding to protect your draft components from scratches. Easily attach or remove the decal holder with a philips head screw dirver.
This unit will fit a 73 mm (2.8") diameter decal, sticker or label. Also avaialbe in 82 mm (3.2") diameter.
KegLand Part Number: KL00871
The CMBecker Inline Flow Control 4mm Barb is necessary for those looking to use tubing that has an inner diameter of 3/16"
Use with CMBecker In-Line Flow Control Compensator
Stainless steel nipple, only stainless steel touches your beverage
Works with CMBecker International shanks.
Includes CMBecker beer nut
The size is 4mm. When using with 3/16" hose you may need to slightly heat hose (using hot water) to stretch hose over barb (this is how we do it!) Just make sure you clamp it properly to get a good seal
This will not work with a standard shank, it works with CMBecker shanks. These seal at two places and do not have a flat end (see photo)
Keep your draft faucet in perfect working order!
Replace your old or broken friction bonnet to keep your fauce lever moving properly
This friction Bonnet is the piece that sits between the Faucet and the Faucet Knob Lever Collar. Tightening it compresses a washer and creates resistance when opening and closing the faucet.
The most high-quality KOMOS regulator, featuring an integrated nut-hand-wheel that allows for effortless, one-handed tightening to your CO2 cylinder
Internal components are accessible from the backplate for easy cleaning and servicing
Includes a Duotight adapter for EVABarrier tubing and a 1/4" flare fitting with barb, allowing for quick and adaptable gas line setups
The PRV is rated to 65 psi and can be swapped out with 17-psi, 35-psi, or 100-psi rated PRVs if desired
Rubber gauge protectors safeguard gauges from potential damage
Compatible with standard US CO2 tanks
The robust body and precision diaphragm provide high flow rates, and the pressure can be easily and precisely adjusted with the hand dial. Extra thick stainless gauges come with rubber bumpers for added protection. The dial faces are triple-scaled to read in psi, bar and kPa.
The PRV is rated to 65 psi (4.5 bar) for added safety while in use. Comes with male flare thread gas-out with included 1/4" barb and nut. Easily swap out the barb to a different size if desired. On the back of the regulator body are three M6 screw holes for mounting (screws not included).
Each KOMOS regulator includes a Duotight Adapter, allowing for quick connection of EVABarrier draft tubing for a solid, yet easy to change, way of connecting gas line. Add Duotight Tees to easily split the line to multiple kegs.
Features:
One-handed Cylinder Tightening: Attach the regulator to your CO2 cylinder effortlessly with one hand using the integrated nut-hand-wheel. No separate spanner or wrench is needed! This is made possible by a new spigot seal design that compresses easily without the risk of damage or leaks.
Simplified Self-Servicing: Maintain your regulator with ease by accessing the internal components from the backplate. Simply use an 8mm hex/Allen key to remove the regulator knob and access the internals for cleaning, eliminating the need for a vise or specialized tools.
Flared Output: The regulator features an output with 1/4" male flare connection. Each regulator comes with a 1/4" barb and nut as well as an 8mm Duotight adapter for use with your preferred tubing.
Triple-Scale Gauge: Monitor your CO2 pressure accurately with the Class 2.5 gauge, featuring PSI, bar, and kPa scales for easy reading (+/- 2.5% accuracy).
Durable Seat Cap Assembly: The new seat cap is constructed from ultra-high molecular weight polyethylene, providing exceptional resistance to wear and tear. This robust design minimizes the risk of scratching and brass filings, which can lead to pressure creep, even under demanding conditions like forced carbonation.
Reinforced Steel Gauges: Benefit from enhanced durability with thicker steel gauges built to withstand rigorous use.
Color-Coded PRV: This regulator includes a 65 PSI green PRV (pressure relief valve). This can be swapped to the Red (35 PSI) or Gray (100 PSI) PRV if desired.
Easy Mounting: Integrated M6 mounting holes allow for secure and convenient installation. Note that the nut-wheel needs to be removed for flush mounting.
Specs:
0–60 PSI operating range
Low pressure gauge reads from 0–100
Pull ring PRV rated to blow off at 65 PSI
1/4" & 5/16" barb fittings included
Duotight adapter for EVABarrier tubing included
Standard US CO2 Threads (CGA320)
Gauge protectors
M6 mounting screw holes
Made in accordance with AS 4267
The CMBecker Inline Flow Control 7mm Barb is necessary for those looking to use tubing that has an inner diameter of 5/16 or 3/8"
Use with CMBecker In-Line Flow Control Compensator
Stainless steel nipple, only stainless steel touches your beverage
Works with CMBecker International shanks.
Includes CMBecker beer nut
The size is 7mm which is slightly wider than 1/4" at 0.27"
This will not work with a standard shank, it works with CMBecker shanks.
Narrow 0-25 psi operating range allows for fine-tuning and accurate dispensing of carbonated beverages
Includes both Duotight and barb fittings for use with EVABarrier tubing or standard gas tubing
Features a shutoff valve for safe operation and standard US CO2 tank threads (CGA320)
Rubber gauge protectors safeguard gauges from potential damage
Compatible with standard US CO2 tanks
The KOMOS Dual Gauge Precision Dispensing Regulator provides precise control for dispensing carbonated beverages. Its narrow 0-25 psi operating range allows for finer pressure adjustments and greater accuracy compared to regulators with wider ranges. This design enables operators to easily fine-tune the output pressure within typical draft dispensing pressure settings.
The regulator includes both Duotight and barb fittings for compatibility with EVABarrier draft tubing and standard gas tubing. The gas outlet features a shutoff valve for safe and convenient operation. Rubber gauge protectors are also included to safeguard the gauges from potential damage.
Features:
0-25 PSI operating range
Low pressure gauge reads from 0-30 psi
Pull ring PRV rated to blow off at 25 psi
Narrow pressure range for increased precision
1/4" & 5/16" barb fittings included
Duotight adapter for EVABarrier tubing included
Standard US CO2 Threads (CGA320)
Shutoff valve
Gauge protectors
Ideal for dispensing carbonated beverages
Replacement lever collar for Intertap or NukaTap faucets. This beer faucet part threads onto the lever and sits above the friction bonnet. Used to help adjust your tap handle to face forward if it is oriented at an angle when fully threaded onto the faucet lever.
Minimize oxygen exposure by flattening the bag before filling to keep your wine, cider, spirits, or cold brew as fresh as the day it was made
This cost-effective tool connects easily to your existing brewing setup with a standard ball lock post, making it a simple and quick solution for refilling bladders without expensive machines
Fill your bag-in-box bladder directly from your brewing vessel. The clever design means the bladder's tap is already in place when full, so it's ready to dispense immediately without extra steps or mess
Tired of tricky transfers that risk oxidizing your wine, cider, spirits, or cold brew? The Bag-In-Box Bladder Refill and Transfer Connector simplifies the process, making it easy to fill bladders without losing quality.
This cost-effective tool lets you forget expensive filling machines and get straight to the good stuff. It's designed to be simple and effective.
Key Features:
Easy Filling: Connect the device to your bladder's tap, engage the knob, and fill it just like you would a keg through the yellow ball lock post.
Minimized Oxidation: Before filling, you can flatten the bag to remove all oxygen, ensuring your beverage stays fresh and delicious.
How it works: Simply attach the connector to your bladder's tap. The ball lock post lets you fill from your brewing setup, making the process quick and seamless. Once full, the tap is already in place for easy dispensing.
KegLand Part Number: KL39253
This is a proprietary draft shank only intended for use with CM Becker X1 and V10 flow control faucets. It will not work with generic or other brands of faucets.
The CMBecker International Inline Flow Control 10mm Barb is necessary for those looking to use tubing that has an inner diameter of 3/8". It is slightly smaller than 1/2", but it will fit a 1/2" ID Hose if properly clamped.
Use with CMBecker In-Line Flow Control Compensator
Stainless steel nipple, only stainless steel touches your beverage
Works with CMBecker International shanks.
Includes CMBecker beer nut
The size is 10mm which is between 1/2" and 3/8". When using with 3/8" hose you may need to slightly heat hose (using hot water) to stretch hose over barb (this is how we do it!) When using with 1/2" it will be loose, but we have used it with syphon hose and thicker high heat (EJ beverage or silicone) hose. Just make sure you clamp it properly to get a good seal.
This will not work with a standard shank, it works with CMBecker shanks
G-Type keg coupler for Anchor Steam and some other European kegs
Pull-to-engage ergo lever handle
Includes 3/8" OD barb for gas inlet
Bass G style keg tap, also known as, keg coupler, coupling, or adapter. Fits Anchor Brewing kegs.
Will also fit:
Abbot Ale
Anchor Liberty Ale
Anchor Porter
Anchor Steam
Bass Pale Ale
Blackthorne Cider
Caffrey's
Fuller's ESB
Fuller's London Pride
Grolsch
Old Speckeled Hen
Rouge
Scottish Tennents
Sir Perry William's
Watney's
Young's
Young's Chocolate Stout
Young's Oatmeal Stout
Young's Ram Rod Bitter
Young's Special London Ale
