Dispensing
-
Beer Faucet Shank | Stainless | 4" | Intertap® | NukaTap®
Comes with a back nut, plastic collar, hex nut, and a 1/4" barb. Requires a 1" hole saw for installation. When set in place, the shank will only have about 2 1/2" of length to pass through your wall or fridge door, due to the length of the collar and back nut. Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 5-1/8" - Total Length (Tip to Tip) 4" - Shank Length (Without Nut & Barb) 3" - Thread Length 2-1/2" - Pass Through Length Kegland Part number: KL01113
$36.49
-
Tailpiece - 1/4 in. (Set)
Perfect addition when purchasing a new sanke style keg coupler or tap. New taps typically come with the correct fittings for your gas line but not your beverage line. These are those fittings! Used to connect 3/16" or 1/4" beer line. To connect 3/16" beer line tubing it is helpful to heat the tubing end in hot water.
$6.29
-
KOMOS® Stainless Steel Sanke Keg Beer Tap - D-Style Keg Coupler (With PRV)
The KOMOS D-Style coupler is built for use with the most common commercial sanke kegs sold in the USA. Featuring stainless steel body and stainless steel probe, this keg tap is made to last. The coupler comes without fittings so it can be adapted however you sees fit. When assembling, insert the rubber "duck bill" check valve into the side gas-in port. The check ball and ball retainer are placed in the top beverage-out port. Both gas-in and bev-out ports come bare so you can fit it out exactly how you want it. Maybe you like a larger gas line and smaller beer line—no problem. Or perhaps you're ready to take your draft system into the 21st century with EVABarrier draft tubing and Duotight push-to-connect fittings. Whatever floats your boat, keep your draft setup anchored with the KOMOS keg coupler. The Green corny keg-style PRV is rated to 4.5 BAR (65 psi). It can be swapped out with PRVs with a higher or lower pressure rating if desired. Always check the pressure rating of your keg before swapping PRVs.
$44.99
-
KOMOS® Kegerator | Replacement Main Circuit Board | Standard | Deluxe | Double-Wide
Replacement main circuit board for the KOMOS standard, delux, and double-wide kegerator. Not compatible with outdoor or commercial kegerators.
$21.99
-
5 lb CO2 Tank | Premium Aluminum | New | CGA320 Valve | US DOT Approved
Made from corrosion resistant, engineered Aluminum New high quality CGA-320 valve DOT approved Brand new aluminum 5 lb CO2 tank made from high strength aluminum alloy and high quality CGA320 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It’s called a 5 lb tank because it holds 5 lbs of compressed (liquified) CO2. 5 lbs of CO2 is enough to dispense about 8 to 9x 5-gallon kegs of homebrew. Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder. Tanks should always be stored in an upright position. Features: Made from corrosion resistant, engineered Aluminum Brushed finish Thick, durable cylinder walls 18" T x 5.25 Ø DOT approved New high quality CGA-320 valve Light weight compared to steel tanks
$89.99
-
KOMOS® Universal 50 | Dual Gauge CO2 Regulator | 0–50 PSI
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in early August. Handles both dispensing and rapid burst carbonation, ideal for seltzers and high-carbonation drinks requiring 30-40 psi Includes both Duotight and barb fittings for use with EVABarrier tubing or standard gas tubing Features a shutoff valve for safe operation and standard US CO2 tank threads (CGA320) Rubber gauge protectors safeguard gauges from potential damage Compatible with standard US CO2 tanks The KOMOS Dual Gauge Precision Universal Regulator is suitable for both dispensing and carbonating beverages. Compared to the Precision Dispensing model, the Universal model features a wider 0-50 psi operating range, enabling pressures above 25 psi for rapid burst carbonation. This is particularly useful for seltzer and other highly carbonated drinks requiring 30-40 psi dispensing pressure. The regulator includes both Duotight and barb fittings for compatibility with EVABarrier draft tubing and standard gas tubing. The gas outlet features a shutoff valve for safe and convenient operation. Rubber gauge protectors are also included to safeguard the gauges from potential damage. Features: 0-50 PSI operating range Low pressure gauge reads from 0-60 psi Pull ring PRV rated to blow off at 50 psi Narrow pressure range for increased precision 1/4" & 5/16" barb fittings included Duotight adapter for EVABarrier tubing included Standard US CO2 Threads (CGA320) Shutoff valve Gauge protectors Ideal for dispensing or carbonating beverages
$59.99
-
Tailpiece Gasket
With this perfect-fit replacement gasket for your draft equipment, you’ll never have to experience the frustration of trying to “rig it” again. This molded rubber beer line gasket is used anywhere you are mounting a tailpiece. It is placed between the tailpiece and the beer taps and/or shank.
$1.19
-
KOMOS® Matte Black Draft Tower With NukaTap® Faucets (w/ Duotight Fittings)
NukaTap faucets offer reduced first pour foam due to low thermal mass Forward-sealing design prevents beer residue from gumming up the faucet Unique shuttle design greatly improves laminar flow, improving the pour of carbonated beverages Compatible with all Intertap faucet accessories and shanks Matte Black painted finish. See note below. Nothing looks quite as nice as beer pouring out of a sleek, matte black draft tower. These are the same tower kits included with the KOMOS Kegerator, featuring NukaTap Stealth Bomber faucets, EVABarrier draft tubing, and Duotight push-to-connect fittings for easy assembly. The tower is made from 304 brushed stainless steel, making them corrosion resistant while also looking great! NukaTap Stainless Faucets and Towers These kits come with NukaTap Stealth Bomber faucets mounted on a stainless tower with matte black finish. NukaTap is the newest brand of forward sealing faucets that boast a lower thermal mass for reduced first pour foam. They feature a "nuke-shaped" internal shuttle that is made from TPV, which provides superior laminar flow to further reduce foaming issues. All faucet spout attachments and accessories are cross compatible between Intertap and NukaTap. Forward-sealing means that while in the closed position the faucet will keep beer in it instead of draining out. This keeps the internal parts from getting sticky and reduces the chance of off flavors transferring to your beer while you pour. The modular, threaded spout can fit a variety of attachments including a growler filler or stout spout. Duotight Fittings & EVABarrier Draft Tubing Duotight and EVABarrier have revolutionized how you connect draft line, and our tower kits come standard with both. We love Duotight push-in fittings for their quick connection, reliable seal, and versatility. Setting up and connecting draft line has never been easier -- no more hose clamps or heating water to soften tubing! Each tower comes with Duotight fittings for the tower shanks and for splitting gas lines (double & triple tap only). We recommend adding Duotight fittings to use for your keg connections as well. Depending on whether you'll be serving from homebrew kegs or commercial sanke kegs, you'll need two DUO106 or two DUO104 per line. EVABarrier tubing has been engineered with protection in mind and is both PVC-free and BPA-free. This double walled tubing offers superior protection against oxidation, CO2 loss, and microbial growth. EVA tubing is the future of draft line for professional applications, and now your kegerator will feature the same first-class tubing. Includes: Stainless steel draft tower w/ Matte Black Finish NukaTap Stealth Bomber faucet(s) Stainless steel faucet shank(s) with Duotight tailpieces EVABarrier gas and beverage tubing Draft tower mounting screws Faucet wrench 1-3 Tap Tower Dimensions: 13.4 in. tall (without faucets) 3 in. tower diameter 4.4 in. base diameter 4 Tap Tower Dimensions: 13.4 in. tall (without faucets) 4.5 in. tower diameter Interior mounting holes (does not include bottom collar) Please note: this is a painted faucet and as such needs to be used, cleaned, and handled with care. Clean the faucet gently by hand and avoid tossing it into a bucket with other draft parts. Excessive soaking in caustic cleaners will damage the finish. For these reasons, we do not recommend the Stealth Bomber faucets for professional settings. If you prefer a stainless steel spout that can take more punishment, the matte black towers are also sold separately and can be paired with the NukaTap Punisher Edition faucet.
$126.99 - $274.99
-
Shutoff With Check Valve | 1/4" MPT x 1/4" MFL
This shutoff valve can be used for multiple applications. Has a 1/4 in MPT thread on one side, this is commonly used in regulators, air distributors, and other keg system components. The out side has a 1/4 in MFL fitting for attaching a variety of flare fitting such as a barb ans swivel nut for gas lines. Includes a check valve, so gas can only flow in one direction, this can protect your regulator from accidential back up of beer.
$15.49
-
KOMOS® Kegerator | Replacement Gas Cylinder Bracket
We're not here to ask how it happened. We're just here to offer you a replacement gas cylinder bracket if you need it.
$16.49
-
KOMOS® Premium Dual Body CO2 Regulator | Industrial-Grade | 0–60 PSI Operating Range | 1/4" Flare Fittings with Barbed Outlet & Duotight Adapter Fittings
Easily carbonate or dispense beverages at different pressures with the KOMOS Dual Body CO2 Regulator Wide 0-60 PSI operating range suitable for both dispensing and rapid burst carbonation Ideal for seltzers and high-carbonation drinks requiring 30-40 PSI Includes Duotight adapters for EVABarrier tubing and 1/4" flare fittings with barbs, allowing for quick and adaptable gas line setups Heavy-duty steel gauges with rubber bumpers, robust body, and precision diaphragm ensure long-lasting, accurate pressure adjustments Compatible with standard US CO2 tanks and can be adapted for use with Nitrogen / Argon tanks This beefy, industrial-grade regulator will serve you well for years to come. The robust dual-body and precision diaphragms provide high flow rates, and the pressures can be easily and precisely adjusted with the hand dials. Extra thick stainless gauges come with rubber bumpers for added protection. The dial faces are triple-scaled to read in psi, bar and kPa. The PRVs are rated to 65 psi (4.5 bar) for added safety while in use. Comes with male flare thread outlets with included 1/4" barb and nut. Easily swap out the barbs to a different size if desired. On the back of the regulator body are three M6 screw holes for mounting (screws not included). It also comes standard with Duotight Adapters, allowing for quick connection of EVABarrier draft tubing for a solid, yet easy to change, way of connecting gas line. Add Duotight Tees to easily split the line to multiple kegs. The Komos Dual Body Regulator is a beefy, heavy regulator. If you are using with a 5 lb co2 tank you will need to keep your tank in stand or strapped down to keep the tank and regulator from tipping over. The regulator is CO2 ready with standard US CGA320 threads. It can also be used with Nitrogen or Argon tanks with the optional CGA320 x CGA580 Adapter. Features: 0–60 PSI operating range Low pressure gauge reads from 0–100 Pull ring PRV rated to blow off at 65 PSI Strong, robust design Highly accurate precision diaphragm 1/4" flare fittings with barbed outlets & Duotight adapters M6 mounting screw holes Made in accordance with AS 4267
$99.99
-
Beer Faucet Parts | Rebuild Kit
Fix your old, stuck, or leaky faucet with new washers! Most faucets that aren't working properly, just need a good cleaning and some new washers Fits most American beer faucets, including D1200, D1205, D1207, and D1215 Does not work on stout, forward sealing, or European faucets Fix an old faucet that is still functionally sound but is old, leaking or just hard to use. Fits our faucets D1200, D1205,D1207, & D1215 and 95% of all beer faucets ever made. Does not work on stout faucets, the sealed forward faucets, Perlick faucets, nor European faucets.
$3.49
-
NukaTap® Mini Beer Faucet | Duotight Adapter | 8 mm (5/16")
This Duotight 8 mm (5/16") adapter is designed to suit the Nukatap Mini and will allow you to couple the faucet to a wide range of other 8 mm Duotight fittings. This includes attaching it to the Duotight Flow Control Ball Lock Disconnect. This particular type of flow control ball lock disconnect includes a "tang" at the top of the push in fitting that couples with this adapter. The combination of the two fittings prevents the faucet from spinning around while in use. Sold Separately: NukaTap Mini Beer Faucet (D1598) Flow Control Ball Lock Disconnect (DUO159) Mini Self Closing Spring (D1598A) KegLand Part Number: KL32209
$7.69
-
KOMOS® Kegerator | Replacement Temp Control Circuit Board | Standard | Deluxe | Double-Wide
Replacement temperature control circuit board for the KOMOS standard, deluxe, or Double-Wide kegerator. Not compatible with outdoor or commercial kegerators.
$27.49
-
Pressure Gauge (LHT) | High Pressure (0-3000 PSI) | CO2 or Nitrogen Regulator | 1/4" MPT Left-Hand Thread
Great Replacement for a broken gauge. Replacing a broken gauge on your pressure regulator is a snap with this Left Hand Thread 3000 psi Replacement Pressure Gauge for CO2 or Nitrogen regulator. Installation is simple, and it prevents you from needing to buy a whole new regulator. Used to determine level of remaining gas in the tank. 1/4” MPT Left-hand thread.
$16.99
-
Taprite Dual Body CO2 Regulator | High Performance Primary Regulator | Independent Pressure Settings | 0-50 PSI Working Pressure | CGA320 Inlet | One Way Shutoff Valves | 5/16" Barb Outlets
High performance primary regulator designed to handle the workload of dispensing from multiple taps without freezing up! Dual body regulator for setting independent pressure settings—ideal for serving two different beer styles with different optimum carbonation levels High-pressure and double low-pressure gauges to easily reference CO2 cylinder pressure and the two output pressures Pressure settings are easily adjusted by hand using the large plastic adjustment knob CGA320 inlet features a built-in gasket where the unit attaches to the CO2 tank—eliminating the need of replacing fiber washers with each tank swap Made in the USA. Taprite is one of leading manufacturers of gas regulators and draft dispensing equipment One-way shutoff valve outlets protect your regulator from backflow and can be turned on/off to stop gas flow without needing to close your tank When it comes to CO2 regulators, we’ve tried them all. This quality unit by Taprite is our favorite on the market. It’s no wonder this regulator is trusted by so many breweries and beer bars—it represents the best quality at a great price. This dual-body model allows you to send different pressures to two separate kegs from the same CO2 tank! The things you’ll love about this regulator are: The large front knobs make pressure adjustment tool-free, easy & fast. A built-in gasket where the regulator connects to the CO2 tank eliminates the constant replacement of fiber washers every time you change out your tank. The barbed outlets feature one-way on/off valves which prevent backflow and protect the regulator’s internals. The gauges are easy to read. The low pressure gauges read from 0 to 60 psi. The optional available gauge cage is the best on the market. This is the T752HP model, where the HP stands for high performance; it won't freeze up when multiple taps are running at once. Best of all is the consistent pressure regulation. With many regulators the pressure can 'creep' up over time. This unit holds the pressure rock steady. No drifting. Built by Taprite, an American company.
$179.99
-
Faucet Handle | Beer Tap Handle | Black Chrome Plated
The perfect choice for your NukaTap Stealth Bomber or Punisher Edition draft faucet. These black chrome plated tap handles are an excellent upgrade for any kegerator setup. The heavy chrome plated brass will feel great in your hand every time you pour a tall one. 2-5/8" tall. 7/8" wide at the top of the knob. Kegland Part number: KL01373
$7.69
-
Duotight Draft Regulator Board | Gas Manifold | 6 Way
Serve beverages at different pressures without the need for multiple CO2 cylinders, dual body regulators, or expensive gas manifolds Feed a single pressure to the gas board from your regulator and then step down the pressure on each Duotight regulator Use one line for serving ales, another for soda or seltzer water, and another for carbonating a freshly filled keg All parts shown are included and snap together quickly thanks to Duotight push-to-connect fittings and rigid plastic joiners Duotight In-Line Regulators feature built-in pressure gauges that read 0-60 PSI and can be swapped out for different ranges if desired The Duotight Draft Regulator Board is a simple and cost-effective solution to serving beer and other beverages on draft at different pressures. With a standard CO2 tank and CO2 regulator, you can feed gas at a single pressure into the regulator board and then fine tune individual pressure settings for each gas line via the Duotight In-Line Regulators. These regulators feature built-in pressure gauges that make adjustments super simple and check valves are included as standard so you never have to worry about back flow into the regulator. This kit includes everything you need to assemble your regulator board and can be customized so the gas inlet is on the right or left side—whichever makes the most sense for your home draft setup. Duotight push-to-connect fittings and the precut rigid joiners make assembly a breeze and only takes 10-15 minutes! The draft board kit comes in two options—with or without shut off valves. These valves offer peace of mind and allow you to shut off gas flow to any line that is not in use. If you ensure that your system has no leaks, they aren't technically needed, and you can always fully tighten your Duotight Regulator adjustment knob for added protection. But that little extra security might help you sleep easier at night! One advantage of choosing no check valves, however, is that it will leave room at the top of the board to label your gas lines. One of the coolest features of the Duotight In-Line Regulator is that the included pressure gauge can be swapped out for different pressure ranges. The standard gauge reads 0-60 PSI, but if you have one line that will always be used for serving Ales, you can swap to a 0-15 PSI gauge that will be a little easier to read and make precise adjustments. There's also a Digital Pressure Gauge available that provides backlit instant reads and is rated from 0-90 PSI. Don't need 6 gas lines? Check out the 4-Way Duotight Draft Regulator Board. Please Note: Full assembly required. The gas board, regulators, and fittings will arrive loose. Please see our instructions and assembly video below. Stepping Down Pressure The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability. Ideal regulation scenario (10 PSI less than inlet pressure) Example of 30 PSI inlet translating to 0–20 PSI output Kit Includes: 6-Output Gas Board (6) Duotight In-Line Regulators (6) Duotight Check Valves (6) Duotight Shut Off Valves (if selected above) (5) Duotight Tees (1) Duotight Elbow (23) Rigid Plastic Joiners NOTE: All Duotight fittings and rigid plastic joiners come as 8mm OD. Mounting hardware is included for the regulators but not for mounting the board itself to a wall or the inside of your kegerator/keezer. If you select the option without shutoff valves, you will be left with some spare joiners after assembly.
$142.99 - $153.99
-
KOMOS® 22 ft³ Nitrogen Tank | Argon Tank | Beer Gas Tank | Premium Aluminum | New | CGA580 Valve | US DOT Approved
With your own Nitrogen tank, you can add Nitro-Draft capability to your Home Dispense System! Serve beer on Nitro! The best way to pour your favorite stouts and porters! Made from high-quality aluminum that will never rust like steel tanks Fill with Beer Gas Mix to get that alluring, cascading pour famously associated with Guinness CGA580 valve pairs with standard US-style nitrogen & argon gas regulators KOMOS® offers a full suite of first-rate draft products and draft fittings—from kegs to faucets and everything in between! Use pure nitrogen to serve still wine, cold brew coffee, Sangria and premixed cocktails on draft Brand new aluminum 22 cubic feet Nitrogen tank made from high strength aluminum alloy and high quality CGA580 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It can be filled with compressed (liquified) Nitrogen, Argon, or Beer Gas Mix (70% Nitro/30% CO2). Fill with beer gas mix (70% Nitrogen/30% CO2) for dispensing beers "On Nitro". Using 100% Nitrogen is also the recommended gas for dispensing cold brew coffee, wine, or even Sangria and premixed cocktails on draft! Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder. Tanks should always be stored in an upright position. Features: Made from corrosion resistant, engineered Aluminum Brushed finish Thick, durable cylinder walls DOT approved New high quality CGA-580 valve Light weight compared to steel tanks Rated to 2216 PSI service / 3360 PSI test pressure PSI (allowing for Nitrogen fill) Can also be filled with Argon or Beer Gas Mix (Nitrogen/CO2) NOTE: You will need at Nitrogen/Argon Regulator to go with this tank, a standard CO2 regulator will not work.
$110.99
-
Kegland | Universal Beer Tap Faucet Plug | BrewZilla Malt Tube Stopper
Keep your beer taps clean and the fruit flies away with this beer faucet plug! Fits most standard beer faucets Made of highly resistant silicone These unique faucet plugs are designed to fit any faucet from 10 mm all the way up to 17 mm in diameter. These plugs are an economical solution to any fruit fly, yeast, or bacteria buildup when the faucet is not in use. The silicone is resistant to caustic and acid based cleaners as well as high temperature so they are dishwasher safe. This cap also functions as the stopper for the malt extension tube on the BrewZilla System. This cap will prevent grain from going down the tube. Kegland Part number: KL04220
$2.79
-
Duotight Push-In Fitting | 8 mm (5/16") | 5-Way Multi-Tee
Compact Design: Ideal for tight spaces inside small refrigerators or keezers. Versatile Routing: Use any port as the inlet to feed the remaining three outputs. Easy Expansion: Pair with DUO102 plugs to customize the number of active lines. Streamline Your Draft Setup with the Duotight 4-Way Tee Tired of bulky manifolds and a web of splitters? This compact Duotight tee is the ultimate space-saver for 4-tap kegerators. Whether you are splitting a single CO2 line to four separate kegs or distributing liquid lines, this single fitting replaces the need for multiple daisy-chained tees. The push-to-connect design allows you to plumb your primary line into any port and instantly branch off to four different outputs. If you aren't using all four lines yet, simply use the Duotight 8mm Plug (DUO102) to cap the unused ports. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. KegLand Part Numbers: KL46268
$4.99
-
Faucet Handle | Beer Tap Handle | Chrome Plated
These chrome plated tap handles are an excellent upgrade for any kegerator setup. So sleek! So shiny. The perfect mate for any chrome plated or stainless steel draft faucet. 2-5/8" tall. 7/8" wide at the top of the knob. Kegland Part number: KL01373
$6.59
-
D-Style Keg Coupler | Sanke Keg Beer Tap | Stainless Steel Probe | PRV | Beer & Gas Barbs Included
D-Type keg coupler for standard American sanke kegs Stainless steel keg probe Click-to-engage ergo lever handle Includes 1/4" OD barbs for gas inlet and liquid outlet The most popular keg coupler in the USA. Commercial D-Style sanke beer tap, also called a coupler, has a lock down mechanism that gives a solid click when engaged. Heavy duty construction is designed to withstand commercial usage. Beer is dispensed out of the top port, the side port is for gas. Nickel coated body with stainless steel probe This is the default tap used by most American Craft breweries. Here is a partial list of breweries that have been reported to being using American D style kegs. Abita ACME Alaskan Alexander Keith Anderson Valley Bad Frog BayHawk BBC Black Dog Blanche de Chambly Blue Moon Breckenridge Brooklyn Bruin Pale Ale Budweiser Busch Carlsburg Celis Cider Jack Columbia Brewing Coors Coors Light Corona Deschutes Black Butte Devil Mountain Dos Equis Eel River Brewing Ellicottville E.J. Phair Fat Tire Firehouse Firestone Flying Dog Foster's Full Sail Genesee George Killian's Irish Red Goose Island Gordon Biersch Grant's Green Mountain Cidery Hamms Hard Core Cider Henry Weinhard's High Falls Holy Cow Red Hornsby's Hudson Valley Humboldt Ice House Killarney Killian's Irish Red Kirin Ichiban Kokanee Labatt Blue Leinenkugel Little Kings Lost Coast Lowenbrau (US) Mad River Maudite Miami Trail Brewing Michael Shea's Michelob Mickey's Middle Ages Miller Milwaukee's Best Modelo Molson Canadian Moosehead Natural New Amsterdam New Zeland Steinlager Nor'Wester North Coast O'Doul's Old Milwaukee Old Vienna Pete's Portland Mactarnahan's Amber Portland Oregon Honey Pyramid Razors Edge Red Ale Red Dog Red Hook Red Wolf Rogue Dead Guy Ale Rogue Hazelnut Brown Rogue Red Rolling Rock Sam Adams Saranac Saxer Brewing Schmitt's Shiner Bock Ship Inn Shipyard Sierra Nevada Sleemans Southpaw Spanish Peaks Black Dog Starr Hill Brewery Steinlager Strohs Tecate Thomas Kemper Trois Pistoles Unibroue Wasatch Weinhard's Whitbread Ale Widmer Hefeweizen Woodchuck Dark & Dry Cider Wyder's Yuengling Zebra Kegland Part number: KL06064
$32.99
-
NukaTap® Stainless Steel Beer Faucet | Matte Black Finish | Stealth Bomber Edition | Forward Sealing
Reduced first pour foam due to low thermal mass Forward-sealing design prevents beer residue from gumming up the faucet Unique shuttle design greatly improves laminar flow, improving the pour of carbonated beverages Compatible with all Intertap faucet accessories and shanks Matte Black painted finish. See note below. First Pour Foam Reduction Every kegerator owner knows the letdown of pouring your first pint of the day and getting too much foam. Even with perfectly balanced draft lines, first pour foam is sometimes unavoidable simply due to the temperature of the faucet itself. Running beer through the faucet will drop the temperature, and the foaming will subside, but not without a bit of wasted beer from pouring off excess head. The NukaTap Stealth Bomber beer faucet drops to beer serving temperature much faster thanks to its lower thermal mass. Simply put, the bulkier the faucet is, the more beer is needed to flow through and chill the tap. The NukaTap is over 20% lighter than its Intertap predecessor, and even lighter still compared to other brands of faucets. Improved Laminar Flow The inspiration for the NukaTap name comes from its uniquely designed "nuke-shaped" shuttle that resides on the inside of the faucet. The NukaShuttle went through numerous rounds of redesigns and countless hours of testing to find a shape that provides superior laminar flow. This means that liquid passes by the shuttle with very little resistance, allowing highly carbonated beers or hard seltzers to pour like a dream. Sanitary Design The NukaShuttle is the world’s first seamless single-piece design. Traditional taps feature an o-ring seated on a stainless steel shuttle, which can cause a couple of issues. After many pours, the stainless shuttle rubbing against the internal body of the faucet will create small fissures that become potential infection sites, and the seated o-ring can be difficult to clean in place, making your draft cleaning and sanitizing process less effective than you realize. The NukaShuttle is an advanced TPV rubber matrix that has been seamlessly formed over a durable PP skeleton. This single-piece design eliminates the pitfalls of older manufacturing methods, making it one of the most sanitary faucets on the market. Forward Sealing vs. Rear Sealing From tap rooms to home bars, forward-sealing faucets are the ideal choice for any draft setup. In traditional rear-sealing taps, beer will drain out of the entire faucet when it's in the closed position. This means the internal mechanism is coated in beer, which then dries and becomes a sticky residue. Forward-sealing faucets, on the other hand, keep the tap full of beer so it never has a chance to dry and gunk up the internal parts. This makes the faucet much easier to clean and also reduces the chance of off flavors transferring to your beer while you pour. Faucet body & lever made from stainless steel Shuttle made from TPV O-rings made from EPDM Lever collar & friction bonnet made from brass Matte black finish NSF approved Kegland Part Number: KL17978 Please note: this is a painted faucet and as such needs to be used, cleaned, and handled with care. Clean the faucet gently by hand and avoid tossing it into a bucket with other draft parts. Excessive soaking in caustic cleaners will damage the finish. For these reasons, we do not recommend the Stealth Bomber faucets for professional settings. If you prefer a stainless steel spout that can take more punishment, see the NukaTap Punisher Edition faucet.
$40.49
-
NukaTap® Beer Faucet Parts | Replacement Ball Seal | Cup Washer Seal
Single replacemelt ball seal (cup seal) for NukaTap draft faucets. Component #3 in the faucet diagram below. Each NukaTap has two of these washers. Also compatible with Intertap brand faucets. Not compatible with the NukaTap Mini faucet. How to tell what generation NukaTap you have. Generation 1 - Two White Nylon Cup Seal Washers Generation 2 - Two Red Self Lubricating Nylon Cup Seal Washers Generation 3 - Two Black POK Cup Seal Washers KegLand Part Number: KL43908
$1.49
-
NukaTap® Mini Beer Faucet | Wall Mount Shank Kit | 8 mm Duotight
Designed specifically for mounting the NukaTap Mini Beer Faucet on any kegerator, keezer, cold room wall, or other flat surface Connect beer line directly to the faucet, reducing the amount of temperature loss to a standard draft shank No spinning faucets. Your tap will remain in a fixed orientation once locked into the collet Easy installation. No need to drill a large hole through your fridge to accommodate a standard 5/8" draft shank Use with 8 mm OD EVABarrier draft tubing Note: Faucet Sold Separately This shank kit is specifically designed to suit the NukaTap Mini Beer Faucet and will allow you to connect the NukaTap Mini to a cooler box, kegerator, keg fridge, cold room wall or any other flat surface. This wall mount shank kit is for use with 8 mm OD EVABarrier. For the shank kit for use with 6.35 mm OD EVABarrier, see here. New Innovative Shank Design Unlike other shank kits, this kit doesn't use a bulky 5/8" threaded shank. The issue with a standard draft shank is that acts as a heat sink, and due to the fact that most shanks sit inside an insulated wall, this results in a substantial amount of warm beer coming out of the tap before cold beer starts flowing. This results in substantial "first pour foam" effect which wastes beer, can result in sour beer, and ultimately negatively effects the quality of the beverages being served. This new design has the beer line feed all the way directly up to the back of the faucet, greatly reducing the volume of non-refrigerated beer. No Spinning Shanks If you have ever installed a traditional 5/8" long shank, you will know how frustrating it is when you use the faucet and it starts rotating. This new design of shank alternative uses three screws that lock the tap into a fixed position and prevents the taps from rotating. If you loosen the 1/2" stainless tap collet you can still have the flexibility to rotate the faucet to any orientation, but once the collet is tight, interlocking teeth on this shank kit and the NukaTap Mini will hold the tap permanently in the correct orientation. Easy Installation Another advantage compared to standard shanks is that this kit doesn't require you to drill a large 3/4"-1" hole through the wall. As no shank is required, only a hole large enough to accommodate the beer line is required. As a result, an 8mm (5/16") conventional drill bit is all that is necessary for installation. However, if you are concerned about the small amount of beer sitting in the draft line inside the wall not being refrigerated, you can also shell out a larger diameter of foam on the inside of the wall to allow cold air to circulate around the beer line thus reducing the non-refrigerated beer in the line even more. If you wanted to do this the Step Drill Bit is the best tool for the job. Any Wall Thickness Other shank kits will require you to purchase a specific length shank for a specific wall thickness. This new shank alternative will fit any wall thickness. If you have wall thicknesses that are less than 2.7" thick then you can use the included screws that have "snap off" points so you can simply cut the screws down to the desired length. However, if the wall is thicker than 2.7" you can simply purchase a conventional screw from the hardware store and screw the shank kit to your wall. If the substrate is firm enough you may not even need to go all the way through the wall so a common 1-1/4" long screw may be all that is required. Specifications: Beer Line Diameter: 8 mm OD EVABarrier Collet and Screw Cover: 304 Grade Stainless Steel O-ring Material: Dual O-ring Silicone/EPDM combination Plastic Mounting: Polyketone (POK) Temperature Range: 14-212°F (-10-100°C) Max Pressure: 150 psi KegLand Part Number: KL32186
$21.99
-
Gauge Cage | For Taprite Regulator | Mounting Bolt & Washer Included
Protect your regulator from damage in the event your tank gets knocked over. A Gauge Cage is cheap insurance that can help save you a costly regulator replacement. Mounting bolt and washer included. CO2 and Nitrogen tanks, especially the 5lb size most brewers use, are notoriously wobbly and easy to knock over once the regulator is mounted on them. This handy Gauge Cage helps protect the gauges themselves, as well as the fragile points where they thread into the regulator body, from damage in case of a fall. Specifically sized to fit our D1060 and D1070 Taprite brand ragulators, these cages may not fit some budget regulators manufactured overseas.
$27.99
-
Replacement PRV | Pull Ring Pressure Relief Valve | Green | 65 PSI
Replacement pressure relief valve rated to blow at 65 psi. This is a direct replacement of the PRV featured on the KOMOS® CO2 regulator. The Green PRV can also be used with pressurizable FermZilla models for hydro testing. Note that under normal operation, the FermZilla should always be used with the Red PRV.
$7.69
-
Perlick 630SS Front Seat O-Ring
Replacement front seat o-ring for the Perlick 630SS faucet. This is the gasket that the push back handle comes into contact with, stopping flow of the beer.
$1.29
-
CMBecker In-Line Flow Control Compensator
Add the perfect amount of restriction to any beer line to reduce foam. Eliminates the need for flow control in the faucet itself. Great for use in Jockey Boxes or anywhere you are serving beverages with varying levels of carbonation. If you are currently using a long length of tubing to increase restriction you can now shorten your tubing. A shorter line holds less beer. Beer that is stored in the line tends to warm up quicker, adding to foaming issues, and is more likely to stale from bacteria present in the line. Features: Adjust flow with an included Allen wrench (keeps unauthorized people from adjusting the unit) Eliminate foam from beer or slow down / speed up other beverages Fix systems with issues without having to replace lines or faucets Take the guesswork out of line restriction. You can use shorter lines and still have perfect restriction. You can also use larger ID lines and adjust as necessary. Easy to disassemble for cleaning, clear body for easy monitoring Made in Germany by CM Becker from Food grade plastic and stainless steel parts! Comes Equipped with 2 x 3/16" Barbs Easy to install to any existing beer line (cut line and install two clamps)
$54.99
-
Drip Tray - 15.7 in. Wall Mount
Stainless steel drip tray with pre-punched wall mounting holes. 15.5" wide with 5" tall backsplash. The grill is removable for easy cleaning. Perfect for 4–5 faucets. Specs: Back splash: 5" tall Grill: 15.5" W x 6.625" D Overall width: 15.8" Overall depth: 6.75" Removable grill Made from stainless steel KegLand Part number: KL01397
$65.99
-
Stainless Steel Tee | 5/16 in Barb
3-way stainless steel tee with 5/16" barbed ends. Use the tee to split gas lines to push multiple kegs with one CO2 tank. KegLand Part Number: KL04442
$5.49
-
Intertap® Chrome Plated Beer Faucet | Forward Sealing
The Intertap faucet is a forward sealing faucet with a modular, threaded spout which can fit a variety of different attachments including a growler filler or a stout spout. In normal rear-sealing faucets the entire faucet has to drain of beer. In forward-sealing faucets the faucet keeps beer in it so the inside doesn't have a chance to get sticky, making cleaning much easier. It also reduces the chance of off flavors transferring to your beer while you pour. Other forward sealing faucets use a floating o-ring, which is just as sanitary but requires the o-ring to move inside the faucet body in order to seal correctly. This can become a problem as the faucet ages. Intertap faucets use a sliding shuttle that guides the o-ring into the perfect position every time. The threaded spout easily unscrews from the faucet and can be replaced by a growler filler or stout spout quickly and easily. Pour a pint and then fill a growler in no time at all. Made of chrome plated brass. Kegland Part number: KL00987
$29.99
-
Stainless Steel Growler Filler | Intertap® | NukaTap®
This is a rather simple, but extremely effective way to fill growlers from your draft system! Going to a party, but don't want to bring a keg of homebrew? Filling straight from the faucet creates a lot of foam, and you lose carbonation. Simply plug this filler into your faucet, attach some 3/8" tubing, and fill! This model is designed to fit Intertap faucets. Compatible with Intertap and NukaTap faucets. Kegland Part number: KL01045
$6.59
-
Stainless Steel Growler Filler - Fits Perlick 630SS & 650SS
Take your beer on the go with the help of this handy growler filler attachment for Perlick 630SS and 650SS faucets. Filling growlers straight from the tap is tough task, and you're more than likely to lose most of the beer's carbonation in the process. By running a short line of 3/8" tubing from the growler filler to the bottom of your growler, the beer can flow gently into the vessel and fill from the bottom up. Be sure to use the flow control knob to slow down the flow rate. If you're using the standard faucet, you may want to turn down the PSI on your regulator before filling.
$10.99
-
NukaTap® Mini Beer Faucet | Stout Spout
The Stout Spout installs on the NukaTap Mini to improve the pour of your stouts and nitro brews The creamer/aerator disc inside strips out nitrogen gas for a creamier beer Simply unthread the standard spout from the NukaTap Mini and swap in the Stout Spout Simply unscrew the normal spout from the NukaTap Mini and screw this Stout Spout in its place to pour your nitro brews. This spout has a creamer/aerator disc inside that strips out the nitrogen gas for a creamier beer. Only compatible with the NukaTap Mini faucet. The Stout Spout will have a 1/4" female flare thread. KegLand Part Number: KL32858
$8.79
-
Stainless Steel Shuttle for NukaTap® Beer Faucet
This stainless steel shuttle can be used to replace the TPV rubber NukaShuttle that comes standard in the NukaTap beer faucet. For users that prefer stainless internal mechanisms in their faucet. You will need to remove the bonnet piece at the handle, pull the handle out and then slide the shuttle piece out. Compatible with all NukaTap faucets, including Gen 2 Flow Control. KegLand Part Number: KL35958
$5.49
-
KegLand Benchy Sparkling | Countertop Water Carbonator & Chiller | Instant Pour Sparkling Water
Instant and infinite sparkling water at your fingertips whenever you want it! Benchy connects to your household's water supply, chills, carbonates, and delivers on demand Serve up to 8 gallons of chilled, carbonated water per hour Pair with draft faucets and place it on your counter, or install it under the counter and plumb it to a mounted water faucet See below for detailed installation video Benchy Sparkling is the answer for instant chilled and carbonated water on demand. Simply connect your household water supply and CO2 Cylinder to the unit and receive unlimited sparkling and chilled water from the draft faucets. The chiller is highly efficient with very little power draw while idle and has enough cooling capacity to serve up to 8 gallons of sparkling water per hour. This unit comes without shanks or draft faucets, as it can be used as a countertop unit or installed under your counter and routed to a faucet you install on your counter or kitchen sink. If you plan to use it as a countertop unit, we highly recommend NukaTap Flow Control Faucets. Easy Installation: Plug the Benchy into the wall Fill internal water tank Connect household water supply Connect CO2 Cylinder Pour chilled sparking water. It's that simple and you can be enjoying chilled sparkling water in under 1 hour with this setup and barely any time at all to cool down. Ensure that the unit is installed and operated according to the instruction manual which can be found below. Fully Adjustable The Benchy Sparkling has an integrated digital temp controller so you can control the temperature from 0.5-10°C (33-50°F). You can also vary the carbonation level from 0.5 volumes to over 5 volumes for super bubbly water. Cooling Performance The Benchy Sparkling is able to chill about 5 to 8 gallons of sparkling water per hour (based on ambient water and air temperature of 68°F). To further increase the capacity of this unit, you can pre-chill the water from your household supply line either by a holding tank (ball lock keg) in the fridge or a DraftMaster Chiller. If you pre-chill the water you can more than double the output of the Benchy Sparkling. The reservoir temperature on the Benchy should never be set below 2°C (35°F) as you will run the risk of freezing the water inside the carbonation keg. Specifications: 110V Refrigerant: r600a (80 grams) Cooling Power: 600 watts Power Consumption: 155 watts (idle power consumption less than 5 watts) Capacity: approximately 6.6 gal/hour (based on 68°F ambient temperature) Input Gas: CO2 @ 29-50 psi (Requires 8mm (5/16") OD tubing) Input Water: Must be 15 psi higher than gas pressure (Requires 6.35mm (1/4") OD tubing) Sparkling/Chilled Water Out: Requires 8mm (5/16") OD tubing Dimensions: 18.3" H x 11.4" W x 20.5" D (Excluding sight glass that can be removed) Recommended Accessories: CO2 Gas Cylinder CO2 Regulator EVABarrier 4mm x 8mm Tubing PE Water Line Tubing 6.35mm Duotight In-Line Regulator (0-150 psi) Duotight Reducer - 8mm x 6.35mm 8mm Duotight Check Valve Diverter Valve (check water line connection for the size you'll need) Countertop Installation Recommended Accessories: (2) Short Shanks & Hex Nuts (2) Duotight Adapters - Beer Thread x 8mm (2) NukaTap FC Faucets& Self Closing Springs (2) Tap Handles (of your choice) Tube Cutter Faucet & Shank Wrench KegLand Part Number: KL2068
$989.99
-
KOMOS® Replacement Nylon Washer | For KOMOS® CO2 Regulators
A great item to keep on hand just in case. The nylon washer helps form an airtight seal between the KOMOS regulator and your gas cylinder. These washers can wear down over time and need replacing, so we always recommend having a spare or two ready to go so you're not left high and dry when the original washer breaks down.
$1.69
-
Stainless Steel Tailpiece - 1/2 in.
Tailpieces are fittings which connect beer and gas tubing to the different parts of a draft system. One side of the tailpiece features a barb to connect the tubing to, and the other side is held against the tap or faucet shank with collar nut. Tailpieces are available in a range of barb sizes to fit up to your tubing size. 304 stainless steel construction means these pieces won’t rust or harbor bacteria that can ruin the taste of your beer.
$4.19
-
Ball Lock Adapter Tapping Head for Sanke Kegs
If you like serving out of commercial kegs but prefer the ease of using ball lock fittings in your draft system, this adapter is for you. Instead of buying additional keg couplers and beer thread to ball lock adapters, you can use this tapping head to go straight from sanke keg to ball lock. To install, remove the keg spear, place the gasket on the keg ferrule with the beaded side facing up, attach the silicone dip tube and place the tapping head on the ferrule, then secure with the 2" tri-clamp. Be sure to always depressurize the keg before removing the tapping head. Includes: Ball Lock Post Lid 2" tri-clamp Single-side beaded tri-clamp gasket 60 cm silicone dip tube (23.6") Red 2.5 bar PRV (36 psi) KegLand Part Number: KL10610
$65.99 $49.49
-
Growler Filler - Stainless Steel
Love bringing a growler of your brew with you, but hate the waste and mess of filling it off your tap? Just pop this handy Stainless Steel Growler Filler into your faucet, attach an appropriate length of tubing, and proceed to fill from the bottom of the growler up! Filling from the bottom upward will dramatically reduce foaming, which less mess and wasted beer! and fill away! Faucet insert OD is 1/2”, barbed outlet is 3/8” OD. This model fits standard faucets. Will not fit Perlick or Perl faucets as their nozzles have a different inner diameter. For Perlick faucets please checkout item D1224.
$7.69
-
Dual-Threaded Insert For Wooden Taphandles
Your custom-made tap handle will be the talk of the party! You can create your own tap handle and mount it with this threaded insert. Simply drill a 1/2" hole in the bottom of your wooden piece and thread the D1299 with a flathead screwdriver (a coin can also be used in a pinch!). When you’re finished, mount your custom tap handle to your faucet, pull a pint and admire your handiwork! Internal threads are 3/8", 16 thread-per-inch. Mounts to any standard faucet.
$3.29
-
Pressure Gauge | Low Pressure (0-30 psi) | CO2 or Nitrogen Regulator | 1/4" MPT Right-Hand Thread
Great Replacement for a broken gauge. Replacing a broken gauge on your pressure regulator is a snap with this Replacement Low Pressure Gauge for CO2 or Nitrogen regulator. Installation is simple, and it prevents you from needing to buy a whole new regulator. 1/4” MPT Right-hand thread.
$15.99
-
Beer Faucet - Stainless Steel
This industry standard faucet will last a lifetime and will not taint beer flavor. All parts are constructed from stainless steel, which is a strong, food grade metal. Normal faucets wear down with time as the chrome plating wears off and your beer is then exposed to brass. Brass can cause metallic flavors in your beer that don't taste good! This is the first all stainless faucet that has been produced with an affordable price tag. Buy a stainless faucet today and know that you won't have to purchase another faucet in the future. You can also rest easy that your beer will taste just like the brewer intended. Will fit all North American shanks and towers making it a great replacement faucet. Quick lever action. Polished stainless finish.
$32.99
-
Self Closing Faucet Spring | NukaTap® Flow Control G1
The NukaTap FC is the world's only forward-sealing flow control tap that can use an auto close spring. By inserting the spring between the flow control device and NukaTap shuttle, the tap will automatically close when you let go of the handle. This is perfect for customers who may not be diligent enough to remember to completely turn off the tap after each pour. Or for those with little kids or pesky cats that knock everything around! This very inexpensive spring can save you from emptying an entire keg and then losing a whole bottle of gas. Please note: this spring is not compatible with the standard non-flow control NukaTap faucet or the NukaTap Flow Control G2. KegLand Part Number: KL17985
$2.19
-
Intertap® Faucet Kit - Stainless
Get all of the amazing features and functionality out of your Intertap faucet! This kit includes all of the accessories that can be paired with the Stainless Steel Intertap forward sealing faucet. Whether you want to fill a growler or pour a stout, this faucet does it all. Everything you need to dispense from and maintain your Intertap faucet! This Kit Includes: Stainless Steel Intertap Beer Faucet (D1210) Intertap Stout Spout (D1213) Intertap Growler Filler Spout (D1214) Intertap Ball Lock Spout (D1217) Intertap Self-Closing Faucet Spring* (D1212) Intertap Seal & Gasket Kit (D1215) *Does not include shank.
$71.99
-
Beer Faucet Shank | Stainless | 2" | Includes 3/16" Nipple Back Nut & Plastic Collar
Comes with a 3/16" nipple, back nut, and plastic collar. It requires a 1" hole for installation. When set in place, the shank will only have about 11/16" of length to pass through your wall or fridge door, due to the length of the collar and back nut. Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 3-3/4" - Total Length (Tip to Tip) 2-1/8" - Shank Length (Without Nut & Nipple) 1-1/4" - Thread Length 11/16" - Pass Through Length
$19.99
You have seen 96 out of 257 products