A beer faucet is one of the most important features on a draft system. We have a great selection of beer faucets, from brands like Intertap and Perlick, as forward sealing faucets and speciality faucets for nitro stouts. You can make a statement with a gold plated faucet or a stainless steel faucet, with or without flow control if you want to control the flow rate of your beer.
The famous forward-sealing Perlick beer faucet, with integrated Flow Control valve and Push-Back Creamer!
Use the flow control feature to reduce unwanted foaming during the length of the pour, then finish it off with the push-back creamer to top off the beer with the perfect amount of foam. Get ready to start pouring picuture-perfect pints with the Perlick 690SS!
Constructed of 304 stainless steel to last a lifetime.
About Perlick Forward Sealing Beer Faucets:
The #1 feature of the Perlick faucet is its forward sealing design. Why is that so important? An ordinary, rear-sealing faucet closes by pushing a shuttle against the faucet shank, at the rear of the faucet. So once the tap is closed the faucet is still full of beer that has to be drained out. There is actually a pin hole in the back of an ordinary faucet that allows beer to drain. Because of this design, leftover beer residue inside the faucet makes operation sticky and can harbor bacteria which harm your beer’s flavor as it flows through the faucet. In the Perlick faucet, with its Forward Sealing design, beer only has to drain from the short 1" nozzle section. This allows it to always operate smoothly (even when it was not cleaned between uses) and greatly reduces contamination!.
Please note: In order for the push-back creamer to function properly, you must avoid overtightening the tap ferrule. If you're unable to push-back on the faucet lever, check that there's enough room between the tap ferrule and the friction bonnet and back off the tap ferrule as needed.
Tune the Stout Spout on your Intertap or NukaTap faucet with this set of perforated discs! Not all beverages are the same so this kit offers a range of aerator discs so you can find the perfect disc for your stout or cold brew coffee.
The Stout Spout has a removable creamer/aerator disc inside. It is specially made to serve beers infused with nitrogen gas, and allows the nitrogen gas to flow smoothly through the faucet with the beer to create a smoother, creamier beer. With this range of discs, you can mix and match with ease to find which one serves your particular beverage justice with more restriction or more areas for that creaming effect to push through the spout.
Kit Contains:
0.3mm Drilled Disc with 3 x holes
0.3mm Drilled Disc with 5 x holes
0.5mm Drilled Disc with 1 x hole
0.5mm Drilled Disc with 3 x holes
0.5mm Drilled Disc with 5 x holes
0.7mm Drilled Disc with 1 x hole
0.7mm Drilled Disc with 3 x holes
KegLand Part Number: KL12591
The ultimate portable draft faucet! Compact & lightweight with all the advantages of a standard NukaTap forward sealing faucet
Pair with a Flow Control Ball Lock QD & Duotight Adapter and the whole assembly fits in your pocket
Forward-sealing design prevents beer residue from gumming up the faucet
Reduced first pour foam due to low thermal mass and conductivity
Perfect for mobile draft, mini kegs, sampling from fermenters, and can even be installed on your kegerator or keezer
Mini Design – Ideal Flow Rate for Small Systems
Most conventional beer faucets are designed with 3/8" diameter spouts so you can pour a pint in just over 10 seconds. This type of flow rate is great for high turnover bars and commercial venues but isn't necessary or even desirable for all applications. For compact portable systems and home draft systems, a slower flow rate is easier to control and further reduces foaming issues due to the low liquid volume stored in the body of the faucet.
The NukaTap Mini is also more ideal for pouring smaller doses. For example, cocktails where 5-8 oz of liquid is dispensed is difficult to control with a high flow rate tap. For portable systems, the NukaTap Mini with the Flow Control Ball Lock QD & Duotight Adapter assembly is small enough to literally put in your pocket, making it ideal for mini keg setups that you want to be portable or that you want to easily fit inside a domestic fridge where space is tight.
Forward Sealing
Forward sealing faucets are absolutely the way to go when it comes to beer taps. Old legacy taps still exist in the industry that are simply poorly designed. The issue with rear sealing faucets is that beer dries up on the internal piston. Aside from being unsanitary, as more and more beer dries up in these components the faucet can almost glue completely shut causing damaged seals or broken handles (this is particularly the case if it's left for some time to dry out with beer inside). These older legacy designs still exist probably due to poor education. The forward sealing designs do not have this problem and the tap drains out completely with no beer drying up on the mechanical moving parts in the same way. This makes the tap more sanitary and reduces maintenance. In many instances the price is similar so there is no reason to use a poorly designed rear sealing faucet. All NukaTap faucets are forward sealing.
Laminar Flow
Just like the NukaTap SS and NukaTap FC, the NukaTap Mini has been designed with laminar flow in mind. Laminar flow is critical for a beer tap as it means you will pour the beer with minimal foaming and a substantial reduction in wastage. Think about how many times a beer faucet opens and closes in its lifetime. 1,000 or maybe 10,000 times? Laminar flow saves wasted beer in excessive foam and the better laminar flow easily pays for itself in a reduction in lost beer. To use poorer designed faucets is essentially flushing money down the sink. Extensive modeling has been done on the NukaTap design to improve laminar flow.
Integrated Seals That Are Indestructible and More Sanitary
Unlike other designs, the NukaTap Mini body is made from Polyketone (POK) making it strong, robust, and able to be autoclaved. The seals are also over-molded from Santoprene® making them hard wearing so they will literally last for the lifetime of the tap without the need for replacement. Santoprene® and POK both have excellent resistance to chemicals such as caustic soda, peroxide, phosphoric acid, lactic acid, citric acid, acetic acid, and all common chemicals sold and used in the beverage industry. The seals internally are over-molded meaning no fissures or cracks exist for bacteria, crud, or yeast to hide.
Superior First Pour Foam Due to Low Thermal Mass and Conductivity
First pour foam is an issue caused by a warm tap body. For most faucets to pour well it's important to dispense enough beer to cool the tap body down to reach maximum performance. In addition to this the conductivity of the tab body also makes this worse so insulative materials simply work better than conductive materials. The NukaTap mini not only has very low thermal mass but is also highly insulative being made mostly from Santoprene® and POK. The combination of these two factors in conjunction with superior laminar flow makes for the lowest "first pour foam" effect out of any tap ever produced.
Long Shank Alternative
Most conventional beer faucets require a large 3/4" hole to be drilled through the side of your refrigerator, keezer, or cold box wall. Traditional long shanks also generally have a large volume of liquid that sits inside the wall unrefrigerated which is not ideal. New long shank alternatives developed for the NukaTap Mini are designed to suit any wall thickness and greatly reduces the stagnant beer sitting in the shank itself. For walls up to 2.7" thick, these wall mount shank kits include three screws, however if the wall is thicker, you can also use 6 small wood screws or something similar and attach three screws from the front and 3 from the back allowing you to go into any wall type.
Another advantage of this new design is the tap will never accidentally rotate. Typically, other long shank beer taps rely on the hex nut on the shank to be done up tight enough to prevent rotation but if the wall compresses (often the case with foam walls) the tap is allowed to rotate. This new design has three fixing points making it impossible for the tap to rotate accidentally as the interlocking teeth behind the collet allow you to set the angle and then do up the collet to fix the tap permanently in that position.
NukaTap Mini Accessories (Sold Separately):
Duotight Flow Control Ball Lock QD (DUO159)
Mini Self Closing Spring (D1598A)
Duotight Adapter - 8mm (D1598B)
Long Shank Alternative for Wall Mounting - Duotight 8mm (D1598C)
Long Shank Alternative for Wall Mounting - Duotight 6.35mm (D1598D)
Stout Spout (D1598E)
Vertical Clamp On Assembly (D1598G)
Horizontal Clamp On Assembly (D1598H)
This chrome plated Draft Beer Faucet will keep your bar or kegerator looking great for years to come.
Industry standard faucet for draft beer that fits North American shanks and towers
Chrome Plated Brass body with quick action brass lever
Specifications:
Body Thread: 1 1/8” – 18 Thread (North American Beer Industry Standard)
Lever Thread: 3/8” – 16 UNC (Unified Coarse Thread); FIts standard tap handles.
Chrome Plated Brass Body
Brass Lever
This Duotight 8 mm (5/16") adapter is designed to suit the Nukatap Mini and will allow you to couple the faucet to a wide range of other 8 mm Duotight fittings. This includes attaching it to the Duotight Flow Control Ball Lock Disconnect. This particular type of flow control ball lock disconnect includes a "tang" at the top of the push in fitting that couples with this adapter. The combination of the two fittings prevents the faucet from spinning around while in use.
Sold Separately:
NukaTap Mini Beer Faucet (D1598)
Flow Control Ball Lock Disconnect (DUO159)
Mini Self Closing Spring (D1598A)
KegLand Part Number: KL32209
Reduced first pour foam due to low thermal mass
Forward-sealing design prevents beer residue from gumming up the faucet
Unique shuttle design greatly improves laminar flow, improving the pour of carbonated beverages
Compatible with all Intertap faucet accessories and shanks
First Pour Foam Reduction
Every kegerator owner knows the letdown of pouring your first pint of the day and getting too much foam. Even with perfectly balanced draft lines, first pour foam is sometimes unavoidable simply due to the temperature of the faucet itself. Running beer through the faucet will drop the temperature, and the foaming will subside, but not without a bit of wasted beer from pouring off excess head. The NukaTap Stealth Bomber beer faucet drops to beer serving temperature much faster thanks to its lower thermal mass. Simply put, the bulkier the faucet is, the more beer is needed to flow through and chill the tap. The NukaTap is over 20% lighter than its Intertap predecessor, and even lighter still compared to other brands of faucets.
Improved Laminar Flow
The inspiration for the NukaTap name comes from its uniquely designed "nuke-shaped" shuttle that resides on the inside of the faucet. The NukaShuttle went through numerous rounds of redesigns and countless hours of testing to find a shape that provides superior laminar flow. This means that liquid passes by the shuttle with very little resistance, allowing highly carbonated beers or hard seltzers to pour like a dream.
Sanitary Design
The NukaShuttle is the world’s first seamless single-piece design. Traditional taps feature an o-ring seated on a stainless steel shuttle, which can cause a couple of issues. After many pours, the stainless shuttle rubbing against the internal body of the faucet will create small fissures that become potential infection sites, and the seated o-ring can be difficult to clean in place, making your draft cleaning and sanitizing process less effective than you realize. The NukaShuttle is an advanced TPV rubber matrix that has been seamlessly formed over a durable PP skeleton. This single-piece design eliminates the pitfalls of older manufacturing methods, making it one of the most sanitary faucets on the market.
Forward Sealing vs. Rear Sealing
From tap rooms to home bars, forward-sealing faucets are the ideal choice for any draft setup. In traditional rear-sealing taps, beer will drain out of the entire faucet when it's in the closed position. This means the internal mechanism is coated in beer, which then dries and becomes a sticky residue. Forward-sealing faucets, on the other hand, keep the tap full of beer so it never has a chance to dry and gunk up the internal parts. This makes the faucet much easier to clean and also reduces the chance of off flavors transferring to your beer while you pour.
NOTE: The Punisher Edition faucet features a matte black body with stainless spout. Other models are pictured as example photos. For the all black NukaTap faucet, see the Stealth Bomber Edition.
Faucet body & lever made from stainless steel
Shuttle made from TPV
O-rings made from EPDM
Lever collar & friction bonnet made from brass
Matte black finish / brushed stainless spout
NSF approved
Kegland Part Number: KL26482
Please note: this is a painted faucet and as such needs to be used, cleaned, and handled with care. Clean the faucet gently by hand and avoid tossing it into a bucket with other draft parts. Excessive soaking in caustic cleaners will damage the finish. For these reasons, we do not recommend the Punisher Edition faucets for professional settings.
Keep your draft faucet in perfect working order.
Replace your old coupling nut to keep your faucet firmly attached to your shank
Knurled finish makes gripping easy
With this faucet replacement nut you can renew a worn-out part on your well-used draft faucet. This replacement part is the nut that attaches the faucet to the shank.
Knurled finish makes it easy to snug even with wet hands.
This replacement gasket installs on the backside of your faucet. Seals between where the faucet and the draft shank connect.
Comes in a convenient zip lock bag.
Keep your draft faucet in perfect working order.
Replace your old friction washer to keep your faucet lever moving properly
This is the second washer of a two part set (D1200D)
With this washer you can renew a worn-out part on your well-used draft faucet. This replacement part is the second washer of a two part set that is used to control motion of lever.
Designed specifically for mounting the NukaTap Mini Beer Faucet on any kegerator, keezer, cold room wall, or other flat surface
Connect beer line directly to the faucet, reducing the amount of temperature loss to a standard draft shank
No spinning faucets. Your tap will remain in a fixed orientation once locked into the collet
Easy installation. No need to drill a large hole through your fridge to accommodate a standard 5/8" draft shank
Use with 8 mm OD EVABarrier draft tubing
Note: Faucet Sold Separately
This shank kit is specifically designed to suit the NukaTap Mini Beer Faucet and will allow you to connect the NukaTap Mini to a cooler box, kegerator, keg fridge, cold room wall or any other flat surface.
This wall mount shank kit is for use with 8 mm OD EVABarrier. For the shank kit for use with 6.35 mm OD EVABarrier, see here.
New Innovative Shank Design
Unlike other shank kits, this kit doesn't use a bulky 5/8" threaded shank. The issue with a standard draft shank is that acts as a heat sink, and due to the fact that most shanks sit inside an insulated wall, this results in a substantial amount of warm beer coming out of the tap before cold beer starts flowing. This results in substantial "first pour foam" effect which wastes beer, can result in sour beer, and ultimately negatively effects the quality of the beverages being served. This new design has the beer line feed all the way directly up to the back of the faucet, greatly reducing the volume of non-refrigerated beer.
No Spinning Shanks
If you have ever installed a traditional 5/8" long shank, you will know how frustrating it is when you use the faucet and it starts rotating. This new design of shank alternative uses three screws that lock the tap into a fixed position and prevents the taps from rotating. If you loosen the 1/2" stainless tap collet you can still have the flexibility to rotate the faucet to any orientation, but once the collet is tight, interlocking teeth on this shank kit and the NukaTap Mini will hold the tap permanently in the correct orientation.
Easy Installation
Another advantage compared to standard shanks is that this kit doesn't require you to drill a large 3/4"-1" hole through the wall. As no shank is required, only a hole large enough to accommodate the beer line is required. As a result, an 8mm (5/16") conventional drill bit is all that is necessary for installation. However, if you are concerned about the small amount of beer sitting in the draft line inside the wall not being refrigerated, you can also shell out a larger diameter of foam on the inside of the wall to allow cold air to circulate around the beer line thus reducing the non-refrigerated beer in the line even more. If you wanted to do this the Step Drill Bit is the best tool for the job.
Any Wall Thickness
Other shank kits will require you to purchase a specific length shank for a specific wall thickness. This new shank alternative will fit any wall thickness. If you have wall thicknesses that are less than 2.7" thick then you can use the included screws that have "snap off" points so you can simply cut the screws down to the desired length. However, if the wall is thicker than 2.7" you can simply purchase a conventional screw from the hardware store and screw the shank kit to your wall. If the substrate is firm enough you may not even need to go all the way through the wall so a common 1-1/4" long screw may be all that is required.
Specifications:
Beer Line Diameter: 8 mm OD EVABarrier
Collet and Screw Cover: 304 Grade Stainless Steel
O-ring Material: Dual O-ring Silicone/EPDM combination
Plastic Mounting: Polyketone (POK)
Temperature Range: 14-212°F (-10-100°C)
Max Pressure: 150 psi
KegLand Part Number: KL32186
Replacement flow control shuttles for the Gen 1 NukaTap FC model faucet (D1584). These pieces are only for the flow control apparatus in the faucet, not the NukaShuttle itself.
A backwards compatible replacement shuttle for the Gen 2 NukaTap Flow Control Faucet is coming soon.
KegLand Part Number: KL17817
Replacement flow control shuttles for the Gen 2 NukaTap Flow Control faucet. These pieces are only for the flow control apparatus in the faucet, not the NukaShuttle itself.
These pieces are backwards compatible with the Gen 1 NukaTap Flow Control model, replacing part numbers 11 and 12 in the diagram image above.
KegLand Part Number: KL17817
The classy way to say "Don't you dare drink my beer!" Do you have a draft system and live with either teenage kids or thirsty roomates? This can potentially be a beer draining arrangement. When you leave for the weekend, stop the flow with a faucet lock. A quick easy locking system that attaches directly to the faucet.
Specifically designed for Perlick 630 series draft faucets. For standard beer faucets, please see D1274.
Keep potential “beer-samplers” and kids out of your draft system with this Beer Faucet Lock.
Give yourself some peace-of-mind, knowing that your draft system is locked and your beer is safe. If you're a serious homebrewer this thought has crossed your mind: the thought of someone walking by and pulling on the tap handle, letting beer run out. Be it friends or your kids, you want your system to be secure. This quick and easy Beer Faucet Lock attaches directly to the faucet. It gives a solid squeeze on the handle, locking it into place, without fear of damaging it. This one-of-a-kind lock is something you’ll be glad you own.
Please note - this lock will not work with Perlick 650SS, 630SS or Intertap faucets
Keep your draft faucet in perfect working order.
Replace your old ball washer to keep your faucet lever moving properly
This is the first washer of a two part set (D1200C)
With this washer you can renew a worn-out part on your well-used draft faucet. This replacement part is the first washer of a two part set that is used to control motion of lever.
Keep your draft faucet in perfect working order!
If the lever gets stuck or is unused for a long time, it can break
Replace it to keep using your favorite tap handle and keep the beer flowing!
With this brass lever you can renew a worn-out part on your well-used draft faucet. This is the actual lever that opens and closes the faucet, and where the tap handle is threaded on. These levers can break if a faucet is left alone for too long and the lever gets stuck.
Don’t shop around for separate components when you can get our faucet, shank, and knob combo all in one kit!
This kit includes our Stainless Faucet, Stainless 4" Shank with 1/4" nipple, and a Faucet knob, combined into one. Please note that the actual useable length of the shank will be about 3 5/8", due to the hex nut and tailpiece attached to it.
Keep your draft faucet in perfect working order.
Replace the washer that seals the sliding shaft of your faucet to prevent leaks
With this washer you can renew a worn-out part on your well-used draft faucet. This washer seals the sliding shaft, which often becomes brittle with age causing the faucet to drip.
Designed specifically for mounting the NukaTap Mini Beer Faucet on any kegerator, keezer, cold room wall, or other flat surface
Connect beer line directly to the faucet, reducing the amount of temperature loss to a standard draft shank
No spinning faucets. Your tap will remain in a fixed orientation once locked into the collet
Easy installation. No need to drill a large hole through your fridge to accommodate a standard 5/8" draft shank
Use with 6.35 mm OD EVABarrier draft tubing
This shank kit is specifically designed to suit the NukaTap Mini Beer Faucet and will allow you to connect the NukaTap Mini to a cooler box, kegerator, keg fridge, cold room wall or any other flat surface.
This wall mount shank kit is for use with 6.35 mm OD EVABarrier. For the shank kit for use with 8 mm OD EVABarrier, see here.
New Innovative Shank Design
Unlike other shank kits, this kit doesn't use a bulky 5/8" threaded shank. The issue with a standard draft shank is that acts as a heat sink, and due to the fact that most shanks sit inside an insulated wall, this results in a substantial amount of warm beer coming out of the tap before cold beer starts flowing. This results in substantial "first pour foam" effect which wastes beer, can result in sour beer, and ultimately negatively effects the quality of the beverages being served. This new design has the beer line feed all the way directly up to the back of the faucet, greatly reducing the volume of non-refrigerated beer.
No Spinning Shanks
If you have ever installed a traditional 5/8" long shank, you will know how frustrating it is when you use the faucet and it starts rotating. This new design of shank alternative uses three screws that lock the tap into a fixed position and prevents the taps from rotating. If you loosen the 1/2" stainless tap collet you can still have the flexibility to rotate the faucet to any orientation, but once the collet is tight, interlocking teeth on this shank kit and the NukaTap Mini will hold the tap permanently in the correct orientation.
Easy Installation
Another advantage compared to standard shanks is that this kit doesn't require you to drill a large 3/4"-1" hole through the wall. As no shank is required, only a hole large enough to accommodate the beer line is required. As a result, an 8mm (5/16") conventional drill bit is all that is necessary for installation. However, if you are concerned about the small amount of beer sitting in the draft line inside the wall not being refrigerated, you can also shell out a larger diameter of foam on the inside of the wall to allow cold air to circulate around the beer line thus reducing the non-refrigerated beer in the line even more. If you wanted to do this the Step Drill Bit is the best tool for the job.
Any Wall Thickness
Other shank kits will require you to purchase a specific length shank for a specific wall thickness. This new shank alternative will fit any wall thickness. If you have wall thicknesses that are less than 2.7" thick then you can use the included screws that have "snap off" points so you can simply cut the screws down to the desired length. However, if the wall is thicker than 2.7" you can simply purchase a conventional screw from the hardware store and screw the shank kit to your wall. If the substrate is firm enough you may not even need to go all the way through the wall so a common 1-1/4" long screw may be all that is required.
Specifications:
Beer Line Diameter: 6.35 mm OD EVABarrier
Collet and Screw Cover: 304 Grade Stainless Steel
O-ring Material: Dual O-ring Silicone/EPDM combination
Plastic Mounting: Polyketone (POK)
Temperature Range: 14-212°F (-10-100°C)
Max Pressure: 150 psi
KegLand Part Number: KL32193
Includes the newest Gen 3 POK cup seal washers
Provides a full set of seals to quickly fix leaks, replace lost seals, or maintain taps used in demanding settings
Compatible with all standard NukaTap beer faucets (not suitable for the flow control model)
This handy kit contains all the seals needed for the standard NukaTap stainless beer faucet. Regardless of which generation of seals your faucet came with, you can replace or upgrade them with the Gen 3 POK cup seal washers.
For the NukaTap Flow Control seal kit, see here.
Most of the seals in this kit are durable and won't require frequent replacement. However, if you experience a leak, accidentally lose a seal, or use the tap in a demanding commercial environment, this kit has you covered.
When replacing seals, we recommend applying a food-grade lubricant to ensure a long-lasting and secure fit. As you take the tap apart, it can also be helpful to take a picture or make a note of where each seal is located to make reassembly easier.
Includes:
The Nuke!
Tap Coupling Washer
Bonnet Washer
2 x Black Generation 3 POK Cup Seal Washers
Nozzle Washer
How to tell what generation NukaTap you have:
Generation 1 - Two White Nylon Cup Seal Washers
Generation 2 - Two Red Self Lubricating Nylon Cup Seal Washers
Generation 3 - Two Black POK Cup Seal Washers
KegLand Part Number: KL43021
Keep your draft faucet in perfect working order.
Does not react with beer
Is stronger than brass
With this stainless steel lever you can renew & upgrade a worn-out part on your well-used draft faucet. This is the lever that actually opens and closes the faucet, and that the tap handle attaches too. Stainless levers are used to replace broken brass levers because of their strength and ability to not react with beer.
This stainless steel shuttle can be used to replace the TPV rubber NukaShuttle that comes standard in the NukaTap beer faucet. For users that prefer stainless internal mechanisms in their faucet. You will need to remove the bonnet piece at the handle, pull the handle out and then slide the shuttle piece out.
KegLand Part Number: KL35958
Single replacemelt ball seal (cup seal) for NukaTap draft faucets. Component #3 in the faucet diagram below. Each NukaTap has two of these washers.
Also compatible with Intertap brand faucets. Not compatible with the NukaTap Mini faucet.
How to tell what generation NukaTap you have.
Generation 1 - Two White Nylon Cup Seal Washers
Generation 2 - Two Red Self Lubricating Nylon Cup Seal Washers
Generation 3 - Two Black POK Cup Seal Washers
KegLand Part Number: KL43908
The Stout Spout installs on the NukaTap Mini to improve the pour of your stouts and nitro brews
The creamer/aerator disc inside strips out nitrogen gas for a creamier beer
Simply unthread the standard spout from the NukaTap Mini and swap in the Stout Spout
Simply unscrew the normal spout from the NukaTap Mini and screw this Stout Spout in its place to pour your nitro brews. This spout has a creamer/aerator disc inside that strips out the nitrogen gas for a creamier beer.
Only compatible with the NukaTap Mini faucet. The Stout Spout will have a 1/4" female flare thread.
KegLand Part Number: KL32858
This Friction Bonnet is the piece that sits between the body of the faucet and the faucet knob lever Collar. Tightening it compresses a washer and creates resistance when opening and closing the faucet.
Fits all Intertap and Nukatap faucet models.
Includes every replacement seal for the NukaTap Flow Control faucet, ensuring you're prepared for any maintenance needs
This kit contains all the seals needed to upgrade a Gen 1 NukaTap Flow Control faucet to the Gen 2 mechanism, improving performance and longevity
Provides a full set of seals to quickly fix leaks, replace lost seals, or maintain taps used in demanding settings
This complete kit provides all the replacement seals you need for the Gen 2 NukaTap Flow Control faucet. If you have the Gen 1 Flow Control model, you can use the improved flow control mechanism in this kit to effectively upgrade your faucet to the Gen 2 Flow Control model.
Most of the seals in this kit are durable and won't require frequent replacement. However, if you experience a leak, accidentally lose a seal, or use the tap in a demanding commercial environment, this kit has you covered.
When replacing seals, we recommend applying a food-grade lubricant to ensure a long-lasting and secure fit. As you take the tap apart, it can also be helpful to take a picture or make a note of where each seal is located to make reassembly easier.
Includes:
The Nuke!
Bonnet Washer
2 x Black POK Cup Seal Washers
Nozzle Washer
Flow Control Arm Seals
Flow Control Arm Thread Seals
Gen 2 Flow Control Mechanism
KegLand Part Number: KL44950
Perfect for mobile draft dispensing with the NukaTap Mini Beer Faucet
Clamp onto a cooler to make a jockey box without needing to drill out shank holes
Makes for a great temporary shank option for kegerators and keezers when you need an extra tap
This bracket is compatible with ice chest coolers and fridges that are up to 3.5" thick. It can be adjusted to have the wing nut clamp in either direction, simply unscrew the flange piece from the threaded rod, then unscrew, then thread from the opposing side.
Please note: This item does not include the Mini NukaTap or Shank pieces. It is simply the stainless steel bracket.
Recommended Accessories:
NukaTap Mini Faucet (D1598)
Wall Mount Shank Kit w/ 6.35 mm Duotight (D1598D)
Self Closing Spring (D1598A)
6.35 mm OD EVABarrier Tubing (D1723C)
KegLand Part Number: KL22002
Perfect for mobile draft dispensing with the NukaTap Mini Beer Faucet
Clamp onto a picnic bench or folding table—an ideal option for backyard cookouts or concerts in the park
Makes for a great temporary shank for weekend getaways, camping, or tailgating
This bracket is compatible with table or bench edges that are up to 3.5" thick. It can be adjusted to have the wing nut clamp in either direction, simply unscrew the flange piece from the threaded rod, then unscrew, then thread from the opposing side.
Please note: This item does not include the Mini NukaTap or Shank pieces. It is simply the stainless steel bracket.
Recommended Accessories:
NukaTap Mini Faucet (D1598)
Wall Mount Shank Kit w/ 6.35 mm Duotight (D1598D)
Self Closing Spring (D1598A)
6.35 mm OD EVABarrier Tubing (D1723C)
KegLand Part Number: KL04077
The V10 stainless steel flow control faucet is designed and produced in Germany with some assembly completed in the United States. This faucet contains technology such as the "Closed Piston Chamber with Encapsulated Compression Spring" that allows for a perfect forward seal on the faucet, no beer trapped in dead space to cause the lever to stick, and the ability to push the faucet backwards for an extra creamy head. The compensator itself has an extra long cone for a wider range of compensation and designed to eliminate uncontrolled shifting of the compensator cone. This configuration features a black standard faucet knob, a polished stainless steel faucet lever, and a lever flow control adjustment system.
Please note: The CM Becker X1 and V10 flow control faucets require a proprietary draft shank and will not work with a standard draft shank. Please select on of the draft shanks below to add to your order.
2.5" Chrome Exterior w/ Food Grade Liner (D12907)
2.5" Stainless Steel (D12908)
5-3/8" Stainless Steel (D12909)
Features:
Full length European Flow Control (completely control restriction at the faucet;no restriction line needed)
Made in Germany and assembled in the USA!
Features a built in “Creamer” function so you can put a fine cream head on your beer
Used in restaurants and bars locally and abroad
The faucet handle and draft shank in the example photo are not included.
The X1 Faucet has been used for many beverage dispense applications over the years including beer, soda, carbonated water and other beverages. This faucet is a great choice when you need to dispense very cold beer that might freeze a metal faucet. This configuration features a self-closing faucet lever, and a lever flow control adjustment system.
Please note: the faucet handle and draft shank in the example photo are not included.
Self-Closing, Lever Adjustment
Food Grade (NSF Approved) plastic and stainless steel
Full length European Flow Control (completely control restriction at the faucet;no restriction line needed)
Made in Germany and assembled in the USA!
Features a built in "Creamer" function so you can put a fine cream head on your beer
Used in restaurants and bars locally and abroad
It is time to move forward with the technologically advanced, forward seal faucet from CMB, the V3S. This faucet is very compact, beautifully finished and full of technological advantages to help you pour the perfect beer. The sleek European design complements the look of your beer system.
Please note: the faucet handle in the example photo is not included.
Forward Seal for better sanitation and operation.
Made in Germany and assembled in the USA!
Features a built in “Creamer” function so you can put a fine cream head on your beer
Creamer also works well for coffee beverages where a creamy texture is desired.
304 Stainless Steel construction will not affect the flavor of beer, wine and other beverage
Works well for Beer, Wine and other acidic beverages.
Vents at the top for better sanitation
Closed Piston chamber with encapsulated compression spring, This gives you
Consistent pressure between forward seal o-ring and seating area
Eliminates dripping and leaking issues found in some forward seal designs
Extends the life of the sealing O-ring for years of service between replacements
No beer is trapped in system or exposed to air, which provides more sanitary conditions.
