Ball Lock 5 Gallon Corny Kegs

New Corny Keg ready to use right out of the box New Kegs are trouble-free for years Rubber top and bottoms protect floors from dings Lid includes a tab wth hole welded in so you can hang anything from lid (dry hop our favorite) 304 Stainless Steel and great welds, this will last a tifetime Features Low2 Keg Lid O-ring which offers a 96% reduction in oxygen ingress compared to silicone Ditch the bottles and start kegging today! Save time, reduce the risk of infection and get all those bottles out of the kitchen for good! Brand new 5 gallon Kegland kegs offer convenience, security and insurance when compared to used or reconditioned kegs. There's no need to replace gaskets or other parts, no need to trust that someone else did a good job with reconditioning, and no possibility of residual flavor or aromas getting into your beer! Features: Ball lock 130 PSI Operating Pressure 5 Gallon (19 L) Capacity Dry Hop Tab Welded into Lid 304 Stainless Steel Dimensions: Height: 24.75 in. Diameter: 8.375 in. Kegland Part Number: KL02899

Read more less

A quick and easy draft tubing setup for dispensing your homebrew! This Beer Line Assembly has everything you need to hook a line to your keg and pour. Great for when you're out serving brew on the go or for parties. Includes the ball lock beverage-out quick disconnect, 5 feet of 3/16" beverage tubing, a hand held faucet, and two hose clamps.

Read more less

Getting into kegging has never been more affordable! Grab this 5-gallon ball lock keg for less than half the cost of a stainless corny keg of the same size! Transparent Oxebar Mono plastic makes it easy to see how much beer you have left in the keg. Especially handy when dispensing on the go Floating dip tube comes standard—a huge upgrade over traditional ball lock kegs. Draw the clearest beer inside the keg while leaving sediment behind Oxebar Mono Kegs are made from Nylon impregnated PET and Polyketone (POK) fittings for superior oxygen barrier properties compared to standard PET plastic Wedge seals on the Tapping Head and Ball Lock Caps eliminate points of oxygen ingress found where rubber is traditionally used Lower total oxygen pickup compared to a standard corny keg with silicone lid seal This 5-gallon keg is lightweight, compact and has high oxygen barrier properties with 3x better (meaning less) gas transmission than traditional PET grades of plastic making it suitable for beer storage or other oxygen sensitive carbonated and non-carbonated beverages. The included Ball Lock Tapping Head comes complete with Red & Yellow Ball Lock Caps for gas and beverage, floating dip tube with filter screen, and pull-ring PRV. Molded handles make it easy to remove the tapping head for cleaning and also allow you to stack the kegs on top of each other, even with your ball lock quick disconnects in place. Being made from the Mono Barrier PET Polymer Matrix, rather than stainless steel, this keg is lightweight and an ideal choice for draft dispensing on the go. But with all the key features of a standard corny homebrew keg, plus the added feature of the floating dip tube, the Oxebar Mono Keg makes for an affordable keg option for home dispensing as well. Fit up to 3 of these bad boys in a KOMOS Standard or Deluxe Kegerator, or fit up to 6 in the KOMOS Double-Wide Kegerator. Includes: 20L Amber Mono Barrier PET Oxebar Keg Dual PCO1881 Lid Assembly with Oxebar Black Handles Green Pull Ring PRV (65 PSI) Silicone Floating Dip Tube w/ Filter Attachment Red & Yellow Ball Lock Quick Disconnect (QD) Caps Specs: Height: 25.1" Diameter: 9.2" Volume: 5.28 Gallons Fit up to 3 kegs in the KOMOS Standard & Deluxe Kegerators NOTE: Oxebar Mono kegs are marked with a manufacture date. 2 years after production, and every 2 years after first use, it is recommended that the keg be hydro tested to ensure the keg is holding pressure. Hydro test instructions are below. You will also need a 100 PSI Gray PRV to perform the test. Fill the keg to the brim with room temperature water Replace the Green PRV with a Gray PRV rated to 6 BAR or higher Pressurize the tank to 6 BAR (87 psi) Hold the keg at 6 BAR for 1 minute Release the pressure and immediately remove the Gray PRV and swap back to the Green PRV If leaks or potential points of failure are found, replace the tank KegLand Part Number: KL36054   NOTE: Oxebar kegs are marked with a manufacturer’s “expiry date”. This does not indicate that the keg is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the keg be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the KG520 Tapping Head and D1072 Green PRV to perform the test. If you do not plan to pressurize the keg, the test is not necessary.

Read more less

An affordable option for your first keg or adding to your growing collection These kegs are cleaned, de-labeled, sanitized, pressure tested and guaranteed to hold pressure upon delivery Used kegs may have minor cosmetic damage but are in perfect working order Rubber top and bottoms protect floors from dings These Ball Lock Corny Kegs are a sturdy, reliable keg with the MoreBeer! seal of approval. These corny kegs are cleaned, de-labeled, sanitized, pressure tested and guaranteed to hold pressure upon delivery. Every Ball Lock Cornelius Keg has a 5 gallon capacity and a rubber top and bottom. While these are used kegs with slight cosmetic damages, these light dings and scratches have no effect the keg’s performance. The relief valves, poppets and gaskets on these used kegs are not replaced before shipping, but we sell all of these items separately if you’d like to replace them yourself at home (part numbers KEG540, KEG450 & KEG500). If you’re looking for a truly economical way to serve your beer at home, this Ball Lock Cornelius Keg is a great option. Used keg with minor cosmetic damage only Ball lock corny kegs measure approximately 8.5" (diameter) x 25" (height) x 26 1/4" Height with flare fittings Soda kegs may come with either 11/16 inch body connects or 7/8" body connects Purchase deep sockets to remove body connects (part numbers KEG991 and KEG992)

Read more less

Connect two ball lock homebrewing kegs together via their ball lock our fittings. Handing for moving sanitizer or beer from one keg to the next. We often use this fitting when we have a big party where we dixie chain kegs together.  For example if you made 10 gallons of pale ale you can use this jumper to connect the two kegs so that all 10 gallons can pour at once.  

Read more less

New Corny Keg ready to use right out of the box New Kegs are trouble-free for years Rubber top and bottoms protect floors from dings Lid includes a tab wth hole welded in so you can hang anything from lid (dry hop our favorite) 304 Stainless Steel and great welds, this will last a tifetime Features Low2 Keg Lid O-ring which offers a 96% reduction in oxygen ingress compared to silicone. Ditch the bottles and start kegging today! Save time, reduce the risk of infection and get all those bottles out of the kitchen for good! Brand new 2.5 gallon Kegland kegs offer convenience, security and insurance when compared to used or reconditioned kegs. There's no need to replace gaskets or other parts, no need to trust that someone else did a good job with reconditioning, and no possibility of residual flavor or aromas getting into your beer! These Premium 2.5 gal kegs have a lid with an internal tab/hook under the lid designed specifically for attaching dry hopping bags. Features: 130 PSI Operating Pressure 2.5 Gallon (9.5 L) Capacity Dry Hop Tab Welded into Lid 304 Stainless Steel Dimensions: Height: 14.5 in. Diameter: 8.375 in. Kegland Part Number: KL02882

Read more less

An upgraded version of our popular Gas Tubing Assembly. Our new assembly now includes 5 ft of 5/16" Ultra Barrier Gas™ PVC Free Beer Tubing, ball lock gas-in quick disconnect (barb) and two hose clamps. EJ Beverages' cutting edge Ultra Barrier Gas™ tubing has a number of advantages over regular Vinyl tubing: Clear tubing with red stripe for identification as low pressure gas line PVC Free and BPA Free - containes no DEHP phthalates or other plasticizers Environmentally friendly production - does not emit dioxins Remains flexible at lower temperatures Temperature range of -40 to 125° F Pressure rated up to 60 psi

Read more less

You'll love the convenience of using this complete gas tubing assembly for draft beer dispensing. This Gas Tubing Assembly includes a ball lock gas-in quick disconnect fitting, 5 feet of 5/16" gas tubing, and two hose clamps. It's more convenient than having to hunt down all of the individual parts yourself. You'll find several places you can use this assembly in your homebrewing configuration.

Read more less

The Megamouth Torpedo Keg series features an extra-large lid opening for easy cleaning Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams The Megamouth Torpedo Kegs are by far the easiest to clean and maintain out of any ball lock homebrew keg you'll find. With an extra-large lid opening, even the buffest of homebrewer (we hear they do exist!) will have no trouble reaching in for a good scrub when it kicks—no expensive keg washing contraptions needed! The Megamouth makes for an excellent pressurizable fermentation vessel and is the ideal choice for brewers who prefer to add dry hops and other flavoring ingredients directly to the keg. Quality First Here at MoreBeer! we love nothing more than quality interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. Torpedo kegs are machine welded and exceed our standards for quality. This weld quality is possible because these kegs are made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. “In” and “Out” is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Overall for the price and quality, along with free shipping from MoreBeer!, the Torpedo Keg is an amazing value! Specifications: Mouth Opening: 5.8" L x 4.8" W. Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions:   Height (in.) Diameter (in.) 3 Gal 13.4 11.4 5 Gal 17.9 11.4 6 Gal 20.5 11.4 10 Gal 30.3 11.4  

Read more less

Possibly the smallest keg you can make that will fit a corny-style keg lid. This half gallon ball lock keg works perfectly as a pressurizable growler that doesn't require any special fittings or accessories beyond the ball lock draft equipment you probably already own. If you've been considering a permanent soda water line on your draft system, this is the ideal keg to use with the KegLand Continuous Soda Carbonator Keg Lid. The low volume of this corny keg will allow the Carbonator Keg Lid to almost instantly carbonate water as it refills the keg after every pour. This little guy also works great as a line cleaning keg using a small batch of cleaning solution. 5.9" W x 9.9" H KegLand Part Number: KL20893  

Read more less

New Kegs are trouble-free for years Rubber top and bottoms protect floors from dings Perfect laser welds ensure easy sanitation and reduced risk of contamination Made in Italy by AEB, a long-time manufacturer with impeccable attention to detail Ditch the bottles and start kegging today! Save time, reduce the risk of infection and get all those bottles out of the kitchen for good! This brand new 5 gallon keg offers convenience, security and insurance when compared to used or reconditioned kegs. There's no need to replace gaskets or other parts, no need to trust that someone else did a good job with reconditioning, and no possibility of residual flavor or aromas getting into your beer! We import these 5 gallon Cornelius Kegs from AEB Italy, a long-time manufacturer with impeccable attention to detail. Perfect laser welds ensure easy sanitation and reduced risk of contamination. While newer kegs shipped from China may have modern features, they do not provide perfect laser welds and therefore risk contamination over time. You'll be glad you paid a bit extra for this high-quality keg. Tack on our famous Fast & Free shipping and you've got a great quality keg at an amazing value! Ball Lock Style Corny Keg 5 gallon capacity 9" Diam. x 25" Height Maximum working pressure of 130 PSI.  

Read more less

Includes ball lock gas-in quick disconnect (barb), 5 ft of 1/4" ID tubing, and two hose clamps.

Read more less

Due to high demand, the 2.5 gallon is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. Brand new, all-stainless construction ball lock keg Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Set your sights on a brand new Torpedo Keg! The patented, D794,899, sleek all-stainless design represents the pinnacle of quality in ball lock homebrew kegs. With features like welded stainless handles, the ability to stack with fittings in place, amazing quality and a great price we think these kegs will become the standard by which other kegs are measured.    Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Taking your keg on the go? Don't leave home without a custom fitted Torpedo Keg Sleeve! Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions:   Height (in.) Diameter (in.) 1.5 Gal 10.25 9 2.5 Gal 14.75 9 5 Gal 23 9 Please Note: These are about 1/2" wider than standard Ball Lock Cornelius Kegs. Need something a bit slimmer?  Check out our lineup of Slimline Torpedo Kegs!  

Read more less

The Slimline Torpedo Keg series features a smaller diameter to maximize the space in your kegerator or keezer Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Torpedo Kegs too wide? Want to squeeze another keg in your kegerator? The patented design, D794,899, of the Slimline Torpedo Keg is 9% more slim than the classic model with all the same great features. Coming in at about 1/4" thinner than standard Ball Lock Cornelius Kegs, this keg has welded stainless handles and the ability to stack kegs with fittings still in place all at a great price. Quality First Here at MoreBeer! we love nothing more than quality interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. Torpedo kegs are machine welded and exceed our standards for quality. This weld quality is possible because these kegs are made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. “In” and “Out” is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Taking your keg on the go? Don't leave home without a custom tailored Slimline Torpedo Keg Sleeve! Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions:   Height (in.) Diameter (in.) 1.5 Gal 11 8 3/8 2.5 Gal 15 5/8 8 3/8 5 Gal 25 1/2 8 3/8   For a slightly shorter keg, see our Standard Torpedo Kegs!  

Read more less

New Kegs are trouble-free for years Rubber top and bottoms protect floors from dings Perfect laser welds ensure easy sanitation and reduced risk of contamination Made in Italy by AEB, a long-time manufacturer with impeccable attention to detail Imagine this…. you’re out camping with friends, and one of your buddies says he would love to have a cold brew. Then just picture the looks on their faces as you pull your brand new Cornelius Keg out of your cooler, full of your rich home brew! This 2.5 gallon corny keg is perfect for the serious home brewer who loves to brew ½ batches, or is just tight on kitchen space. It will fit pretty much anywhere from coolers to backpacks, in your keezer, or in your fridge. You’ll love the rubber tops on these 2.5 gallon kegs because they have two handles and are easier to stack! It is versatile, travels well and just looks cool! The quality of these Italian-made cornelius kegs is undeniable. They are welded by laser under inert gas which means there are no nooks or crannies where bacteria can hide. They may cost more than kegs made in China but the quality difference is a perfect batch versus a ruined one. Quality is important because your beer may sit in these kegs for months. If bacteria gets into a bad weld they are going to very hard to kill. Key Features: High quality Italian made ball-lock style kegs with rubber top and bottom Kegs are 15" tall, x 8.25" diameter and weigh 7.5 pounds. Max working pressure of 130 PSI.

Read more less

Set of 4 used ball lock kegs and 4 complete o-ring rebuild kits These kegs are cleaned, de-labeled, sanitized, pressure tested and guaranteed to hold pressure upon delivery Used kegs may have minor cosmetic damage but are in perfect working order Rubber top and bottoms protect floors from dings Set of four used ball-lock kegs and four complete o-ring rebuild kits plus free shipping. Each rebuild kit includes 5 o-rings - one for the lid, 2 for the body connects, and 2 for the dip tubes.  These ball lock keg 4 packs ship free, which means a great value for you! A great price on unrebuilt ball lock kegs.  To totally rebuild the keg you should also consider a new relief valve and poppets (part number listed below). To clean the inside Alkaline Brewery Wash works great for eating away residue. We recommend taking these steps yourself before and after each use.  The body connnects on a keg are the metal posts where the quick disconnects attach too. They should be removed for cleaning and sanitizing before each use. Ball lock kegs can come with either 11/16" body connects or 7/8" body connects. We sell deep sockets for the removal of either one. So if you do not have these sockets at home and want to make sure you can disassemble the kegs you may want to purchase both sockets below. Then you will always be covered as your keg collection grows. Ball lock corny kegs are approximately 8.5" Diam. x 25" Height. 26 1/4" Height with flare fittings. Measurements may vary slightly. All kegs are pressure tested in our manufacturing facility and are guaranteed to hold pressure upon delivery.

Read more less

5-gallon Ball Lock Keg made from beverage-grade 304 stainless steel. Ideal for beer, cider, kombucha, cold-brew coffee or any other beverage you want to serve on draft. Single steel handle provides easy mobility while keeping the in & out posts clear for connection. Rubber boot bottom won't scratch up the floor of your kitchen or home bar area. Manufactured in an ISO 9001-certified facility with robotically welded seams for superior quality. The KOMOS Homebrew keg is the perfect option for beer, cold brew coffee, kombucha, cider, or any other beverage you want to serve your home bar patrons on draft. These ball lock kegs are built in an ISO 9001-certified facility and made from beverage-grade 304 stainless steel with robotically welded seams. The single steel handle is positioned away from the ball lock posts, so you'll never have trouble connecting or routing your draft lines. The rubber boot bottom allows you to move your kegs around without fear of scratching up your floors, which is especially nice if your kegerator setup is on hardwood floors, and they can be stacked on top of other homebrew kegs with a rubber top. Comes with a standard corny keg lid with pull ring PRV, providing both manual and automatic pressure relief. Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams Single Ergonomic Steel Handle Rubber Boot Bottom ISO9001 Quality Assurance NSF Approved Made from 304 Stainless Steel 25.25" H x 8.75" D  

Read more less

Due to high demand, the 1.5 ,2.5, and 5 gallon is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.   Everything you need to start enjoying your delicious beer on draft! No longer will you need to clean, sanitize, fill, and cap 50+ beer bottles Includes brand new KOMOS CO2 Cylinder and robust KOMOS Dual Gauge CO2 Regulator Featuring the hottest homebrew keg around—the all-stainless, stackable Torpedo Keg EVABarrier beer & gas line with Duotight Quick Disconnects and adapter fittings The KOMOS Homebrew Kegging Kit has everything you need to start enjoying your delicious creations on draft. Whether you've brewed one batch or one hundred batches, you're already familiar with the laborious process of bottling your beer. Cleaning, sanitizing, filling and capping 50+ 12 oz bottles can take a lot of time and effort. The very first thing you'll appreciate when switching to kegging is that there's only one vessel you need to worry about. But it's still no comparison to the pleasure of pouring a glass of beer straight from the tap! From tank to tap, this kegging kit is made from the highest-quality components, starting with a brand new KOMOS 5 lb CO2 tank and KOMOS Dual Gauge Regulator. Choose from 1.5, 2.5, or 5 gallon Torpedo Keg. These are the hottest homebrew kegs on the market, featuring stackable base, rolled stainless handles, and labeled In and Out body connects for your QDs. Everything it connected with EVABarrier draft tubing and Duotight push-to-connect fittings. EVABarrier is our draft line of choice due to the double-walled design that protects your beer from oxygen ingress and CO2 loss. Duotight fittings make everything come together quickly and easily—and they're just as easy to disconnect if you need to clean or reconfigure your setup. Included: KOMOS Dual Gauge Regulator KOMOS 5 lb aluminum CO2 cylinder Standard Ball Lock Torpedo Keg (1.5, 2.5, or 5 gal) EVABarrier beer & gas lines Duotight Ball Lock Quick Disconnects (QDs) Duotight-compatible plastic picnic faucet KOMOS 7-in-1 Multi Tool Wrench Please note: the CO2 tank ships empty. It can be filled or swapped for a full tank at your local welding or homebrew supply store.

Read more less

Oversized corny keg, great for bigger batches and fermentation Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Set your sights on a brand new Torpedo Keg! The patented, D794,899, sleek all-stainless design represents the pinnacle of quality in ball lock homebrew kegs. With features like welded stainless handles, the ability to stack with fittings in place, amazing quality and a great price we think these kegs will become the standard by which other kegs are measured.    Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake.  Stainless Fermenter We've seen a lot our customers having great success using the 6-gallon Torpedo Keg as a stainless steel fermenter or "kegmenter". The extra headroom that this size offers makes it a great option for fermenting 5-gallon batches. We highly recommend using CellarScience Foam Axe if you're fermenting in the keg. Foam Axe will help reduce krausen buildup, cutting down the chance of clogging issues with the ball lock poppets and the PRV in the keg lid. It should also be noted that leaving your finished beer on the leftover trub from fermentation for too long will eventually lead to off-flavors. If it won't be consumed in 2-3 weeks, transfer your beer to a fresh keg using the Torpedo Keg Buoy which will pick up the clearest beer and leave the sediment behind. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions: 27.15" H x 9" D

Read more less

Due to high demand, the 2.5 and 5 gal are currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.   Everything you need to start enjoying your delicious beer on draft! No longer will you need to clean, sanitize, fill, and cap 50+ beer bottles Includes brand new KOMOS CO2 Cylinder and robust KOMOS Dual Gauge CO2 Regulator Featuring the hottest homebrew keg around—the all-stainless, stackable Slimline Torpedo Keg EVABarrier beer & gas line with Duotight Quick Disconnects and adapter fittings The KOMOS Homebrew Kegging Kit has everything you need to start enjoying your delicious creations on draft. Whether you've brewed one batch or one hundred batches, you're already familiar with the laborious process of bottling your beer. Cleaning, sanitizing, filling and capping 50+ 12 oz bottles can take a lot of time and effort. The very first thing you'll appreciate when switching to kegging is that there's only one vessel you need to worry about. But it's still no comparison to the pleasure of pouring a glass of beer straight from the tap! From tank to tap, this kegging kit is made from the highest-quality components, starting with a brand new KOMOS 5 lb CO2 tank and KOMOS Dual Gauge Regulator. Choose from 1.5, 2.5, or 5 gallon Slimline Torpedo Keg. These are the hottest homebrew kegs on the market, featuring stackable base, rolled stainless handles, and labeled In and Out body connects for your QDs. Everything it connected with EVABarrier draft tubing and Duotight push-to-connect fittings. EVABarrier is our draft line of choice due to the double-walled design that protects your beer from oxygen ingress and CO2 loss. Duotight fittings make everything come together quickly and easily—and they're just as easy to disconnect if you need to clean or reconfigure your setup. Included: KOMOS Dual Gauge Regulator KOMOS 5 lb aluminum CO2 cylinder Slimline Ball Lock Torpedo Keg (1.5, 2.5, or 5 gal) EVABarrier beer & gas lines Duotight Ball Lock Quick Disconnects (QDs) Duotight-compatible plastic picnic faucet KOMOS 7-in-1 Multi Tool Wrench Please note: the CO2 tank ships empty. It can be filled or swapped for a full tank at your local welding or homebrew supply store.

Read more less

Due to high demand, the 2.5 and 5 gallon kits are currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.   Everything you need to start enjoying your delicious beer on draft! No longer will you need to clean, sanitize, fill, and cap 50+ beer bottles Includes brand new KOMOS CO2 Cylinder and robust KOMOS Dual Gauge CO2 Regulator Featuring a brand-new ball lock corny keg with rubber booted bottom and top handles EVABarrier beer & gas line with Duotight Quick Disconnects and adapter fittings The KOMOS Homebrew Kegging Kit has everything you need to start enjoying your delicious creations on draft. Whether you've brewed one batch or one hundred batches, you're already familiar with the laborious process of bottling your beer. Cleaning, sanitizing, filling and capping 50+ 12 oz bottles can take a lot of time and effort. The very first thing you'll appreciate when switching to kegging is that there's only one vessel you need to worry about. But it's still no comparison to the pleasure of pouring a glass of beer straight from the tap! From tank to tap, this kegging kit is made from the highest-quality components, starting with a brand new KOMOS 5 lb CO2 tank and KOMOS Dual Gauge Regulator. Choose from 2.5 or 5 gallon Ball Lock Corny Keg. These brand-new kegs are made in the style of the iconic Cornelius homebrew keg with rubber base and molded rubber handles at the top. Everything it connected with EVABarrier draft tubing and Duotight push-to-connect fittings. EVABarrier is our draft line of choice due to the double-walled design that protects your beer from oxygen ingress and CO2 loss. Duotight fittings make everything come together quickly and easily—and they're just as easy to disconnect if you need to clean or reconfigure your setup. Included: KOMOS Dual Gauge Regulator KOMOS 5 lb aluminum CO2 cylinder Ball Lock Corny Keg (2.5 or 5 gal) EVABarrier beer & gas lines Duotight Ball Lock Quick Disconnects (QDs) Duotight-compatible plastic picnic faucet KOMOS 7-in-1 Multi Tool Wrench Please note: the CO2 tank ships empty. It can be filled or swapped for a full tank at your local welding or homebrew supply store.

Read more less

Brand new ball lock keg—no need to clean out an old, used Coke or Pepsi soda keg! Dual rubber handles make it easy to grip, lift, and move the keg when full Rubber base is less likely to damage flooring in your home or kegerator Made from 304 stainless steel in and commerical-quality FSSC 22000 Certified facility This brand-new, corny-style ball lock keg features a molded rubber base and dual-handle top for easy handling and stacking. The comfortable grip handles make it easier to maneuver when full, while the rubber base protects both your floor and the keg itself. This durable keg is constructed from high-quality 304 stainless steel and manufactured in an IFSSC 22000-certified facility. Features: Ball lock 130 PSI Operating Pressure 2.5 Gallon (9.5 L) Capacity 304 Stainless Steel Produced in an FSSC 22000 Certified Facility Dimensions: Height: 14.75 in. Diameter: 8.75 in.

Read more less

Brand new ball lock keg—no need to clean out an old, used Coke or Pepsi soda keg! Dual rubber handles make it easy to grip, lift, and move the keg when full Rubber base is less likely to damage flooring in your home or kegerator Made from 304 stainless steel in and commerical-quality FSSC 22000 Certified facility This brand-new, corny-style ball lock keg features a molded rubber base and dual-handle top for easy handling and stacking. The comfortable grip handles make it easier to maneuver when full, while the rubber base protects both your floor and the keg itself. This durable keg is constructed from high-quality 304 stainless steel and manufactured in an IFSSC 22000-certified facility. Features: Ball lock 130 PSI Operating Pressure 5 Gallon (19 L) Capacity 304 Stainless Steel Produced in an FSSC 22000 Certified Facility Dimensions: Height: 25.75 in. Diameter: 8.75 in.

Read more less

Super-sized corny keg, great for bigger batches and fermentation Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Has the size and strength of a 15.5-gal commercial keg with the easy to open/clean/fill of a homebrew keg Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Look out below! The Torpedo Keg Depth Charge series just dropped and they're set to send blast waves through the homebrew world. Large-scale homebrewers will appreciate the ability to fit their entire batch into a single 15-gallon ball lock keg, and you can expect the same great features that have made Torpedo Kegs such a hit. Laser welded construction for superior quality, rolled stainless steel handles that will last a lifetime, and stackable design that won't interfere with your fittings. Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving, which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification, which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Specifications: Total Capacity: 15.2 gal. Max Pressure: 130 psi PRV Rating: 85 psi Height: 24.75" Diameter: 16.05" Made from 304 Stainless Steel

Read more less

Super-sized corny keg, great for bigger batches and fermentation Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Look out below! The Torpedo Keg Depth Charge series just dropped and they're set to send blast waves through the homebrew world. Large-scale homebrewers will appreciate the ability to fit their entire batch into a single 10-gallon ball lock keg, and you can expect the same great features that have made Torpedo Kegs such a hit. Laser welded construction for superior quality, rolled stainless steel handles that will last a lifetime, and stackable design that won't interfere with your fittings. Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving, which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification, which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake.  Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Specifications: Total Capacity: 10.1 gal. Max Pressure: 130 psi PRV Rating: 85 psi Height: 18.5" Diameter: 16.05" Made from 304 Stainless Steel

Read more less

Replacement graduation sticker for the Oxebar 5.2 Gallon / 20L PET keg (B286). It is white text displayed over a transparent backing sticker. Please follow the directions on the sticker on how to apply this to your Oxebar tank correctly. Oxebar Keg in photo is not included. KegLand Part Number: KL38010

Read more less