Serve beverages at different pressures without the need for multiple CO2 cylinders, dual body regulators, or expensive gas manifolds
Feed a single pressure to the gas board from your regulator and then step down the pressure on each Duotight regulator
Use one line for serving ales, another for soda or seltzer water, and another for carbonating a freshly filled keg
All parts shown are included and snap together quickly thanks to Duotight push-to-connect fittings and rigid plastic joiners
Duotight In-Line Regulators feature built-in pressure gauges that read 0-60 PSI and can be swapped out for different ranges if desired
The Duotight Draft Regulator Board is a simple and cost-effective solution to serving beer and other beverages on draft at different pressures. With a standard CO2 tank and CO2 regulator, you can feed gas at a single pressure into the regulator board and then fine tune individual pressure settings for each gas line via the Duotight In-Line Regulators. These regulators feature built-in pressure gauges that make adjustments super simple and check valves are included as standard so you never have to worry about back flow into the regulator. This kit includes everything you need to assemble your regulator board and can be customized so the gas inlet is on the right or left side—whichever makes the most sense for your home draft setup. Duotight push-to-connect fittings and the precut rigid joiners make assembly a breeze and only takes 10-15 minutes!
The draft board kit comes in two options—with or without shut off valves. These valves offer peace of mind and allow you to shut off gas flow to any line that is not in use. If you ensure that your system has no leaks, they aren't technically needed, and you can always fully tighten your Duotight Regulator adjustment knob for added protection. But that little extra security might help you sleep easier at night! One advantage of choosing no check valves, however, is that it will leave room at the top of the board to label your gas lines.
One of the coolest features of the Duotight In-Line Regulator is that the included pressure gauge can be swapped out for different pressure ranges. The standard gauge reads 0-60 PSI, but if you have one line that will always be used for serving Ales, you can swap to a 0-15 PSI gauge that will be a little easier to read and make precise adjustments. There's also a Digital Pressure Gauge available that provides backlit instant reads and is rated from 0-90 PSI.
Don't need 6 gas lines? Check out the 4-Way Duotight Draft Regulator Board.
Please Note: Full assembly required. The gas board, regulators, and fittings will arrive loose. Please see our instructions and assembly video below.
Stepping Down Pressure
The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability.
Ideal regulation scenario (10 PSI less than inlet pressure)
Example of 30 PSI inlet translating to 0–20 PSI output
Kit Includes:
6-Output Gas Board
(6) Duotight In-Line Regulators
(6) Duotight Check Valves
(6) Duotight Shut Off Valves (if selected above)
(5) Duotight Tees
(1) Duotight Elbow
(23) Rigid Plastic Joiners
NOTE: All Duotight fittings and rigid plastic joiners come as 8mm OD. Mounting hardware is included for the regulators but not for mounting the board itself to a wall or the inside of your kegerator/keezer. If you select the option without shutoff valves, you will be left with some spare joiners after assembly.
If you want an easy way to balance your beer lines, this is the way to do it. One of the benefits of Flow Control disconnects is you don't need to rely on the small ID or line length to apply flow resistance. Rather than adjusting your line length or size, simply apply additional restriction directly on the Quick Disconnect (QD). This is perfect for people who want to serve a large range of beverages with differing carbonation levels without having to customize each line. Now with the added benefit of Duotight fittings built in.
Please be aware that even in the fully open position these FC disconnects do have some inherent flow resistance so you should use either shorter line or larger ID line that you would when compared with traditional ball lock disconnects.
Flow Control QD vs. Flow Control Faucet
One of the only drawbacks of flow control devices is that they inherently create a small amount of turbulence and therefore can cause foaming. In the past, flow control faucets have been the only common option. Flow control faucets are very popular but due to the fact that they are placed at the very end of the beer line they have no head pressure. As a result, any turbulence created can cause foaming and carbonation to come out of solution.
Flow control ball lock disconnects like these on the other hand have the ability to restrict the flow before the beer enters the beer line so the head pressure created by the beer line keeps the carbonation in solution. Even in the instance that high turbulence is created the beer will be far more resistant to foaming issues. For this reason, flow control ball lock disconnects like these have significantly better performance allowing you the flexibility to adjust line resistance easily but without the introduction of turbulence that creates foaming. It cannot fix over-carbonated beer, but it can reduce the amount of beer line you would need to pour without excessive foaming.
Duotight Ball Lock QDs
The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze!
Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required.
Duotight Push-to-Connect
These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
Compact
The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
Overmolded Poppet
The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out.
Tool-less Disassembly
Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
Extreme Chemical Resistance
No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
Toughness
This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough!
Features:
Ball Lock Quick Disconnect - Bev Out
Adjustable flow rate
Direct connect 8 mm EVABarrier tubing
Compact design won't interfere with keg stacking
Made from highly chemical resistant materials
Dissamble by hand for quick and easy cleaning
KegLand Part Number: KL21418
The Duotight Flow Stopper is a handy devicie to use while filling kegs or when transferring between kegs during filtering or after fining. Simply attach the Flow Stopper to the gas post of your keg, then when the keg is full it will automatically cut off flow and prevent excess beer from exiting your gas post and spilling onto the floor. For even better results, we recommend using the Flow Stopper with the BlowTie Spunding Valve. The BlowTie will enable you to apply head pressure to the keg, meaning you can control the flow speed and reduce the foam generated in the filling process. You will need a short length of 8 mm OD EVABarrier tubing to connect the BlowTie to the outlet of the Flow Stopper. Includes:
2 x Duotight 8 mm x 5/8" FPT (DUO104) 1 x Duotight 8 mm elbow (DUO107) 1 x Duotight 8 mm x 1/4 in. flare (DUO106) 1 x Ball float 1 x Stainless spring 2 x 8 mm OD EVABarrier joiners 1 x Acrylic sight glass Ball lock fitting and BlowTie spunding valve not included.
Kegland Part number: KL09393
These mounting clips feature a swivel design, allowing you to achieve the perfect angle for your tubing layout even after the adhesive is set. The modular design ensures they click together seamlessly and can be detached from the 8mm Duotight side with ease.
Installation Tips:
Surface Prep: For the strongest bond, clean the mounting surface with isopropyl alcohol before application.
Optimal Conditions: Always apply to a warm, dry surface. If installing inside a kegerator or keezer, ensure the unit is turned off and reaches room temperature first; moisture and cold will compromise the adhesive.
Curing Time: Allow the adhesive to set for at least 24 hours before attaching hoses or manifolds.
Recommended for Duotight Gas Manifolds and the Duotight 8mm 5-Way Multi-Tee.
KegLand Part Number: KL48132
Leak-Proof Double O-Ring Technology: Engineered with high-quality EPDM double O-rings, providing twice the sealing surface of standard push-in fittings for maximum reliability and a leak-free draft setup.
Modular & Customizable Gas Control: Features integrated, removable check valves to prevent backflow and a tool-free "pop-tab" design that allows you to easily swap, remove, or plug individual ball valves.
Instant Tool-Free Connectivity: Designed for 8mm EVABarrier tubing, the Duotight push-to-connect system allows for secure, seconds-fast installation with flexible mounting options for any kegerator or fermentation chamber.
Please Note: The Duotight Manifolds feature 8mm Duotight connections at both ends. One end is intended for your gas line and the other can be used to attach another manifold or a variety of accessories. If you will not be installing anything on the other end, you will need a 8mm Plug to cap the opposite end from your Gas In (see below).
Streamline your draft setup with the Duotight Gas Manifold, featuring integrated check valves on every ball valve outlet. These check valves provide essential protection by preventing backflow; however, they can be easily removed if you require gas to flow freely in both directions. 8mm Duotight push-to-connect inlet and outlets allow you to easily connect EVABarrier draft tubing in seconds. Available in 2-Way, 4-Way, and 6-Way configurations.
Customization & Modular Design
This manifold is designed for flexibility. If you need to shut off specific lines permanently, we recommend using the Duotight 8mm Plug (DUO102). Modifying the unit is straightforward: use a thin flat-head screwdriver to pop the black retainer tabs, allowing you to remove or swap individual ball valves as needed. If you wish to expand your manifold the future, multiple Duotight Manifolds can be connected using the 8mm Rigid Joiners (DUO202).
Mounting Solutions
Every manifold comes ready for installation with button-head screws for standard mounting. If you prefer not to drill into your kegerator or fermentation chamber, we suggest using Duotight Adhesive Brackets (DUO263) for a secure, tool-free setup.
High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage.
The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market.
EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free.
No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
KegLand Part Numbers:
KL46220
KL46237
KL46244
Duotight Manifold | User Guide
Universal Filling: Ergonomic trigger design allows you to fill bottles of any shape or depth without extra attachments.
Oxidation Protection: Integrated CO2 purge clears oxygen before filling to maximize shelf life and freshness.
Instant Setup: Tool-free Duotight push-connect fittings provide a fast, leak-free assembly and teardown.
Pure Flavor Path: High-grade stainless steel construction ensures zero off-flavors and effortless cleaning.
Take Your Draft Anywhere: The Duotight Handheld Bottle Filler
Stop leaving your best brews behind. Whether you’re heading to a tailgate, a beach bonfire, or a bottle share, the Duotight Handheld Bottle Filler is the ultimate tool for transitioning your kegged beer into portable bottles without sacrificing quality.
Why Choose the Handheld Filler?
Precision-engineered for the modern homebrewer, this unit ensures that every drop of beer only touches high-grade stainless steel. This keeps your flavors pure and your cleaning process simple. To ensure your beer stays as fresh in the bottle as it was in the keg, the integrated CO2 purge clears out oxygen before you fill, significantly extending the shelf life of your bottled creations.
Faster Setup with Duotight Technology
Gone are the days of wrestling with barb fittings and hose clamps. This updated model comes standard with Duotight push-connect fittings, making assembly and teardown incredibly fast and leak-free. The system is designed for brewers who value their time as much as their beer.
Versatile & Ergonomic Design
The filler's intuitive trigger system and ergonomic handle make high-volume bottling fatigue-free. Unlike counter-pressure fillers that require a specific stopper seal, this gun allows you to fill bottles of any depth or shape without needing extra stems or messy hose extensions.
Key Features:
Oxidation Control: Built-in CO2 jacketing tube purges bottles for professional-level shelf stability.
Universal Compatibility: Fill growlers, bombers, or standard 12oz bottles with ease.
Tool-Free Assembly: Duotight fittings provide a secure, airtight seal that snaps together in seconds.
All-Stainless Path: Ensures no off-flavors and maximum durability.
What’s in the Box:
Bottle Filler
Includes gas/liquid triggers and a protective silicone tip
Red Gas Carbonation Cap w/ 6.35mm Male Duotight stem for quick gas line attachment
Duotight Fitting: 1/4" Male Thread x 6.35mm
Duotight Elbow: 6.35mm Compression x 8mm female.
Duotight Ball Lock Disconnect: 8mm Duotight x Yellow/Black liquid QD
EVABarrier Tubing: 5 ft. length (4mm ID x 8mm OD) for low-foaming transfers
Easily set different pressures downstream from a single CO2 regulator. Serve different beverages at different pressures without the need for expensive regulator manifolds! Compatible with both liquid and gas 8 mm Duotight inlet/outlet for use with 8 mm OD EVABarrier tubing or 8 mm Rigid Joiners The Duotight In-Line regulator works with both gas and liquid. Easily adjust the flow with the yellow adjustment knob. 8 mm Duotight fittings at both inlet and outlet make this unit perfect for use with EVABarrier 8 mm OD tubing (D1717 or D1718). Suitable for applications ranging from 0-150 psi. Since this unit does not have a built-in pressure gauge, it can be used in the full pressure range without ever needing to purchase or swap out the gauge. We recommend using an adjustable relief valve/spunding valve on your keg to set the pressure. Stepping Down Pressure The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability. Ideal regulation scenario (10 PSI less than inlet pressure) Example of 30 PSI inlet translating to 0–20 PSI output This regulator is perfect for lowering your mains water pressure for use with the Continuous Soda Carbonator Keg Lid. Specifications: Pressure Range: 0–150 psi Suitable for mains water pressure Liquid and gas compatible Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends Wall mountable Made from non-corrosive acetyl, nitrile, and stainless parts KegLand Part number: KL02172
Perfectly sized for use with water lines—step down the pressure of your mains for use with water filtration systems Built-in pressure gauge for easy reference when adjusting pressure settings Pressure gauge is interchangeable—swap to different pressure ranges that better suit your application Compatible with both liquid and gas 6.35 mm Duotight inlet/outlet for use with 6.35 mm OD PE Water Line or EVABarrier tubing The Duotight In-Line Regulator works with both gas and liquid. Easily adjust the flow can be adjusted with the yellow adjustment knob. 6.35 mm Duotight fittings at both inlet and outlet make this unit perfect for use with 6.35 mm OD tubing (D1723C or D1727C). Features an integrated pressure gauge so you can quickly and easily dial in your pressure setting. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. The size of the Duotight connection and the extended 0-150 PSI pressure range makes this model perfect for stepping down the pressure of your mains water line for use with water filtration or RO systems. Specifications:
Made from food grade acetal Stainless screws Easily disassembles for cleaning 6.35mm (1/4") Duotight fittings at both ends Interchangeable pressure gauge Gauge reads from 0-150 psi Made with quality EPDM seals Wall mountable WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Kegland Part number: KL26918
Easily set and view different pressures downstream from a single CO2 regulator. Serve different beverages at different pressures without the need for expensive regulator manifolds! Built-in pressure gauge for easy reference when adjusting pressure settings Pressure gauge is interchangeable—swap to different pressure ranges that better suit your application Compatible with both liquid and gas 8 mm Duotight inlet/outlet for use with 8 mm OD EVABarrier tubing or 8 mm Rigid Joiners The Duotight In-Line Regulator is an ideal solution if you want to serve different beers at different gas pressures. In a typical multiple line, multiple pressure system you would run a gas line from your main regulator into a secondary regulator where you would set different pressures. While that is ideal, it is a little pricey. This little sweetheart lets you set different pressures at a far lower cost. What we do is set the main regulator at the highest pressure we want in the system - for example a keg of soda that you want to carbonate and serve at 25 psi. Run the gas line into a manifold and then install one of these after the manifold on each line where you want to decrease the pressure, for example lowering to 10psi to serve your British pale ale and 14 psi to serve your summertime lawnmower lager. Works with both gas and liquid. Easily adjust the flow can be adjusted with the yellow adjustment knob. 8 mm Duotight fittings at both inlet and outlet make this unit perfect for use with EVABarrier 8 mm OD tubing (D1717 or D1718). Features an integrated pressure gauge so you can quickly and easily dial in your pressure setting. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. Stepping Down Pressure The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability. Ideal regulation scenario (10 PSI less than inlet pressure) Example of 30 PSI inlet translating to 0–20 PSI output Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends Interchangeable pressure gauge Gauge reads from 0-60 psi Made with quality EPDM seals Wall mountable WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Kegland Part number: KL15035
Perfect for home use with compact keg setups or on the go for mobile dispensing
Compatible with both 16g and 74g CO2 cartridges
Features a 6.35mm Duotight-compatible barb for fast, hassle-free keg attachments
The Duotight Mini CO2 Regulator is a simple, affordable choice for mini kegs and Oxebar keg setups. This compact regulator is designed to work with both 16g and 74g CO2 cartridges, making it ideal for home use or when you're on the go.
With the 6.35mm Duotight-compatible barb you can connect just about anything within a matter of seconds. Simply pair it with the 6.35mm Duotight Ball Lock QD for a quick and hassle-free connection to your kegs. Or, with the Duotight Reducer, you can adapt the regulator for use with the most common and widely used 8mm Duotight accessories.
For additional protection against liquid backflow, you can integrate a check valve along with some hosing to safeguard your regulator. Please note if liquid enters the regulator, it's no longer functional. Be extremely careful with overfilling your kegs or tipping them over when the gas has run out.
The regulator is capped at 30 psi to ensure you do not accidentally over carbonate or exceed your keg's pressure rating. The gauge reads up to 60 psi to account for potential heat expansion so that it does not break the gauge.
Suitable Gas Cartridges:
16g Cartridge 6-pack (KEG993)
74g Cartridge (KEG969)
KegLand Part Number: KL42000
Seamless Integration: Specifically designed to bridge the gap between portable regulators and full-sized tanks.
Leak-Proof Design: Includes a durable nylon washer to ensure a rock-solid, airtight seal every time.
Ultimate Versatility: Compatible with both the Duotight Mini Regulator and the Core 360 Regulator.
Looking to carry a massive CO2 supply without the bulk? Pair your duotight Mini Regulator with this high-quality adapter to connect directly to standard CGA320 CO2 tanks. Taking your kegged homebrew on the road has never been more convenient.
Simply thread the adapter onto your regulator, then attach the assembly to your CO2 cylinder. It’s the perfect way to make your portable kegging setup even more versatile by utilizing larger, more economical gas sources.
KegLand Part Number: KL42024
This Duotight Bulkhead is the same one used for installing the Thermowell into the lid of the FermZilla. Allows you to add a bulkhead to just about anything that can then be connected to with EVABarrier 8 mm OD Tubing (D1717 / D1718) or 5/16" OD stainless or copper tubing. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. KegLand Part Number: KL14595
This Duotight Bulkhead is the same one used for installing the Temp Twister cooling coil into the lid of the FermZilla. Allows you to add a bulkhead to just about anything that can then be connected to with EVABarrier 9.5 mm OD Tubing (D1719) or 3/8" OD stainless or copper tubing. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL14564
This Duotight reducer fitting can be attached to the Intertap Short Shank with 1/4" Duotight compatible barb (D1242). Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Also attaches to the Plastic Ball Lock Cap, allowing the cap to be used with 8 mm OD EVABarrier. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07481
This Duotight reducer fitting can be attached to the Intertap Short Shank with 1/4" Duotight compatible barb (D1242). Compatible with EVABarrier 9.5 mm OD tubing (D1719). Also attaches to the Plastic Ball Lock Cap, allowing the cap to be used with 9.5 mm OD EVABarrier. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL08648
This Duotight ball valve can be used as an inline shut off valve on draft lines. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL06934
This Duotight check valve is a great idea for protecting your regulator or add it in line with your mains water pressure when using the KegLand Continuous Soda Carbonator Keg Lid. It has a low opening pressure of 1 psi. This check valve is suitable for clean liquids such as water or for gas. Since it cannot be disassembled for cleaning, we do not recommend it for beverage applications. The internal components are made from stainless steel. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & water applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07047Kegland Part number: KL07047
This Duotight elbow fitting is compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL0240
This Duotight joiner fitting is compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL02370
This Duotight plug is used to block up your 8 mm (5/16") tees, elbows or other fittings for gas leak testing or simply to plug an unused section.
Features:
Insert plug and firmly push to connect
Release plug by pushing in the collet on the Duotight fitting
Suitable for both gas & beverage applications
Made from food-grade acetal plastic
Temperature rated to 212°F (100°C)
Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals.
Kegland Part number KL06958
This Duotight fitting makes it easy to split your gas line and run it to multiple kegs. Use one tee for a dual tap kegerator or two tees for a triple tap. You can also pair the tee with the Push-In Pressure Gauge to use the gauge with the BlowTie Spunding Valve. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL02387
This Duotight fitting with 1/4" male thread is a great option for connecting gas line to regulators and manifolds that have 1/4" FPT. Comes with seated O-ring. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL06897
This Duotight fitting with 1/4" Flare is perfect for flared gas and beverage ball lock and pin lock disconnects. It can also be used to connect gas line to the flare fitting found on the KOMOS® CO2 Regulator. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718).
The Duotight fitting does not require a flare washer. See the instructions below for how to ensure a leak-free connection when attaching to flare fittings.
Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design.
High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage.
The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market.
EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free.
No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
Features:
Insert tubing and firmly push to connect
Easily release tubing by pushing in the collet
Suitable for both gas & beverage applications
Made from food-grade acetal plastic
Double O-rings made from highly chemical resistant EPDM
Locking teeth made from stainless steel
Pressure rated to 150 psi
Temperature rated to 212°F (100°C)
Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals.
Ball lock fitting and regulator not included.
Kegland Part number: KL06880
Duotight Female Flare Fittings
This Duotight fitting with 3/8" male thread can be used to convert any female threaded 3/8" connection to Duotight. Comes with seated O-ring. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL18067
This Duotight reducer is used when stepping down from 9.5 mm OD (D1719) to 8 mm OD EVABarrier tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL06941
This Duotight to Female Beer Thread (5/8" BSP) fitting can be used to connect beverage line to faucet shanks instead of a tailpiece, and it's also a convenient option for connecting gas and beverage line to the gas in and bev out on keg couplers. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Faucet shank and keg coupler not included. Kegland Part number: KL06903
This Duotight fitting is designed to go through the wall of a tank, housing, or wall, similar to a pass through shank, so you can run EVABarrier tubing from one side to the other. Compatible with EVABarrier 8 mm OD tubing (D1717 / D1718). With the lock nuts in place, there is approximately 1" of pass through threading. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. KegLand Part Number: KL21036
This Duotight to Male Elbow fitting can be used to route tubing connecting to 8 mm Duotight Ball Lock QDs. This is a great way to keep tubing organized and out of the way in your kegerator. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL18456
This Duotight ball valve can be used as an inline shut off valve on beverage lines. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07474
This Duotight check valve is a great idea for protecting your regulator. It has a low opening pressure of 1 psi. This check valve is suitable for clean liquids such as water or for gas. Since it cannot be disassembled for cleaning, we do not recommend it for beverage applications. The internal components are made from stainless steel. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Compatible with EVABarrier 9.5 mm OD tubing (D1719). This Duotight check valve is a great idea for protecting your regulator. It has a low opening pressure of 1 psi, and since it cannot be opened or taken apart, it is recommended for gas applications only. The internal components are made from stainless steel. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & water applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07498
This Duotight elbow fitting is compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07030
This Duotight joiner fitting is compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07016
This Duotight plug is used to block up your 9.5 mm (3/8") tees, elbows or other fittings for gas leak testing or simply to plug an unused section.
Features:
Insert plug and firmly push to connect
Release plug by pushing in the collet on the Duotight fitting
Suitable for both gas & beverage applications
Made from food-grade acetal plastic
Temperature rated to 212°F (100°C)
Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals.
Kegland Part number: KL06965
This Duotight tee fitting is compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07023
This Duotight fitting with 1/2" male thread is perfect for attaching to the Copper Counterflow Chiller (WC130) and using with 1/2" female threaded Camlock and QD fittings. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL06927
This Duotight ball valve with 1/2" male thread is perfect for attaching to the water input on the Copper Counterflow Chiller (WC130), allowing you to adjust the waterflow while chilling your wort. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07375
This Duotight fitting with 1/4" male thread is a great option for connecting gas line to regulators and manifolds that have 1/4" FPT. Comes with seated O-ring. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL14441
This Duotight fitting with 1/4" Flare is perfect for flared gas ball lock and pin lock disconnects. Can also be used to connect gas line to the flare fitting found on the KOMOS® CO2 Regulator. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Although this fitting would also fit a beverage disconnect, 9.5 mm OD EVABarrier is only recommended for beverage line in long draw draft set ups. The Duotight fitting does not require a flare washer. See the instructions below for how to ensure a leak-free connection when attaching to flare fittings. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL11037
This Duotight to 3/4" female thread fitting can be used to connect beverage or gas line to any fitting with 3/4" MPT. Compatible with EVABarrier 9.5 mm OD Tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL13864
This elbow fitting has a 9.5 mm Duotight connection and a Duotight-compatible 3/8" OD barb. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL18432
This Duotight to Female Beer Thread (5/8" BSP) fitting is perfect for connecting gas line to keg couplers. Although it could be used with 9.5 mm EVA Barrier as a beverage line, this would only be recommended for long draw systems where the beverage line will be 20-25 ft long. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Compatible with EVABarrier 9.5 mm OD tubing (D1719). This Duotight fitting with 5/8" FPT is perfect for connecting gas line to keg couplers. Although it could be used with 9.5 mm EVA Barrier as a beverage line, this would only be recommended for long draw systems where the beverage line will be 20-25 ft long. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Keg coupler not included. Kegland Part number: KL06910
This Duotight fitting is designed to go through the wall of a tank, housing, or wall, similar to a pass through shank, so you can run EVABarrier tubing from one side to the other. Compatible with EVABarrier 9.5 mm OD tubing (D1719). With the lock nuts in place, there is approximately 1" of pass through threading. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. KegLand Part Number: KL21012
Replacement gasket for Duotight 1/2 in. BSP fittings.
Compatible With:
DUO122 - 9.5 mm (3/8 in.) x 1/2 in. BSP
DUO169 - 8 mm (5/16 in.) x 1/2 in. BSP
DUO162 - 6.35 mm (1/4 in.) x 1/2 in. BSP
KegLand Part Number: KL88830
Designed for quick and easy push-in installation with EVABarrier Tubing, eliminating the need for clamps. Tubing can be removed effortlessly by simply pushing in the collet Features a double O-ring design for twice the sealing surface of standard fittings, significantly reducing the chance of leaks and allowing for tighter tubing bends without compromising the seal Constructed with high-quality EPDM O-rings, providing excellent chemical resistance and a longer lifespan compared to silicone or vinyl, while also being BPA-free This Duotight joiner fitting is compatible with EVABarrier 6.35 mm OD Tubing. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL37259
The Duotight Elbow Piece is suitable for 6.35 mm (1/4") PE tubing or most lines with a 6.35 mm outer diameter. Designed for use with stiff PE tubing that is commonly used in water treatment equipment, water filters, reverse osmosis fittings, and other appliances that are directly connected to water lines.
Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. No other push ins on the market have EPDM o-rings.
Features:
Insert tubing and firmly push to connect
Easily release tubing by pushing in the collet
Suitable for both gas & beverage applications
Made from food-grade acetal plastic
O-ring made from highly chemical resistant EPDM
Locking teeth made from stainless steel
Pressure rated to 150 psi
Temperature rated to 212°F (100°C)
Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals.
Kegland Part number: KL18449
This handy part is what you need to connect one side into a standard 6.35 mm Duotight fitting and secure the other side with 3/16" ID tubing using a hose clamp over the tube. We have wide range of stainless stepless hose clamps that you can purchase here. KegLand Part Number: KL25928
Seamless Conversion: Easily adapts 6.35mm EVABarrier tubing to any 8mm female Duotight fitting.
Manifold Ready: Optimized for Duotight Gas Manifolds to facilitate quick-disconnect gas line setups.
Leak-Free Connection: Precision-engineered for a secure, airtight seal using standard Duotight push-fit technology.
This reducer allows you to attach 6.35mm EVABarrier tubing to any 8mm female Duotight fitting. This fitting is recommended for use with the Duotight Gas Manifold, allowing you to connect a Red Ball Lock QD Cap to the manifold for a convenient quick disconnect install on your Gas-In line.
High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage.
The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market.
EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free.
No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
KegLand Part Numbers: KL42642
