Add dry hops without introducing oxygen to your fermenting or finished beer!
Load hops into the Hop Bong, fill it with CO2 via the ball lock cap, and pull the PRV to release oxygen
This is the perfect accessory to protect your finished beer from oxygen ingress when it's still in the fermenter
6 oz capacity per "hop drop"—easily repeat the process if you just gotta have More!
Compatible with all BrewBuilt X-Series fermenters and any stainless conical with 1.5" T.C. top port
The Hop Bong is a versatile pressurizable tri-clamp accessory that is perfect for purging oxygen from your dry hops before dropping them into your fermenter. Load up the Hop Bong, flush it with CO2, purge out oxygen with the handy PRV on top, then simply open the Butterfly Valve to inject your beer with a 6 oz payload of dry hops.
This kit is specifically adapted for use with the BrewBuilt X-Series conical fermenters and can be used with any stainless fermenter with 1.5" tri-clamp top port. The 2" T.C. Hop Bong attaches to a stainless 2" butterfly valve that then connects to a 2" x 1.5" T.C. reducer. This allows the largest capacity Hop Bong to be used with any of the 1.5" T.C. accessory ports on the BrewBuilt Conical's lid.
Hop Pellet Capacity: 150–180g (5.2–6.3 oz)
Kit Includes:
2" Hop Bong
Stainless Ball Lock Cap
Red PRV & PCO1881 Cap Combo
2" BrewBuilt Butterfly Valve
2" x 1.5" Tri-Clamp Reducer
(3) 2" Tri-Clamps
(3) 2" T.C. Gaskets
Warning: Always depressurize your system COMPLETELY before removing fittings from your fermenter.
Airlocks are another one of those necessary pieces of equipment for every homebrewer. If you ferment in a carboy or bucket this 3 piece airlock is a must! It’s a popular alternative to the triple ripple type of airlock because it can be taken apart and cleaned, and is easy to fill. (However we do sell the triple ripple type (FE371) in case you are used to that type and would like to stay with it.) While a simple device not all airlocks are the same. Some other designs have only a couple holes in the plastic lid and this can cause the airlock to pop out during an active fermentation. Our design features multiple holes that allow CO2 to escape easily. Additionally some other airlocks have a cross hatch design on the bottom. We have found this more easily leads to Krausen clogs and the airlock being pushed out of the fermenter. Ours is open, allowing Krausen foam to enter the airlock if necesary. Better to clean your airlock out than to find it laying on the floor next to your fermenter 3 days later. Another cool feature of this 3-piece airlock is that 1/2" ID Silicone tubing will fit onto the center post for use as a blowoff. In the cases where you are using a yeast known to produce lots of Krausen (wlp002 from White Labs or 1968 from Wyeast for example) remove the top cover, remove the plastic 'hat', and install the silicone tubing. Run the silicone tubing into a jar or bucket of water. When fermentation dies back down remove the tubing and replace the hat and cover. Please Note: Airlock only - stopper not included.
Fully carbonate your beer in under 2 days!
With the Carbonating Keg Lid you can quickly carbonate beer without the risk of over carbonating like with the burst carbonation method
Diffusion stone disperses CO2 directly into solution for faster gas absorption
Brand new keg lid complete with o-ring and PRV
The easiest way to carbonate beer. This is a Cornelius keg lid with built-in carbonation stone! Move the lid from keg to keg to carbonate as needed. Allows you to force carbonate quickly using the attached .5 micron stone with the portability of being able to move the lid from keg to keg. No more hassles of trying to attach and unattach line from the "gas in" dip tube. Simply connect your gas quick disconnect to the included fitting on the lid and allow carbonation to begin. Sometimes also called a carbonater.
We constructed the lid by welding on a 1/4" barb to the underside of the lid. To that we attached 2' of 1/4" ID tubing that attaches to a .5 micron carb stone on the other end. The flexible tubing, as opposed to rigid tubing, allows the lid inserted into any cornelius style keg. The top of the lid has a "gas in" ball lock body connect welded in place that works with the KEG710 and KEG730 gas quick disconnects.
Use:
Beer must be stored cold at 34–40°F.
Preboil the stone for 2–3 minutes before using. This assures you that your stone is sterile and any residual oils have been boiled off.
Sanitize the whole keg lid before submersing into your keg filled with beer.
Set your PSI on your regulator to 3–4psi and attach your gas in fitting to the body connect on the lid. Leave keg at this pressure for 1 hour.
Raise your pressure 2PSI per hour until you reach 10–12psi. Leave it at 10–12psi for 24 hours. Pour a pint and test the carbonation. If you think your beer needs more CO2 leave for another 4–6 hours and have another pint.
Remove carbonation lid after carbonation level is satisfactory. Return original keg lid for long term storage.
The Tapcooler Counter Pressure Bottle Filler is an all-new, easy-to-use bottling device!
Allows you to perfectly bottle beer from a forward-sealing beer faucet without CO2 loss
Purge bottles and headspace with CO2 to keep oxygen out, prolonging the life of your beer
Perfect for bottling for competitions, sending bottles home with friends, or to take on the go!
Easy to setup and super easy clean.
For a Duotight-compatible filler, check out the NukaTap Counter Pressure Bottle Filler
The Tapcooler Counter Pressure Bottle Filler is the best way to quickly and easily fill bottles of homebrew directly from your draft system. No need to mess with alternate liquid lines or other complex contraptions. Just slide the Tapcooler into any forward sealing faucet (such as a Perlick, Intertap, or Nukatap) hook up a CO2 line, and you're ready to roll. Whether you're filling bottles for a competition or just grabbing a couple to share with your friends, the Tapcooler is quick and easy to use, and will help maintain the flavor, aroma, and carbonation level of your beer so it tastes the same out of the bottle as it would out of the tap.
A counter pressure bottle filler is the best tool for bottling, as the bottle is under pressure while the carbonated beer flows in, which results in a minimal loss of the CO2 in solution.
The Tapcooler improves upon the standard counter pressure filler, as it plugs directly into your draft faucet. Other counter pressure solutions require you to hook up a separate liquid line, which is not something standard draft systems have setup and requires additional time to prep. With the Tapcooler, you can have it setup and ready to go in less than a minute! The Tapcooler design is also advantageous because after you are done filling the bottle, it stays in place hooked up to your faucet while other fillers require you to set the unit aside and pick it back up again for the next bottle.
Connecting your CO2 line is also a snap. You can either hook up directly with a 3/16" push-fit line, or connect your line to the included barb fitting. You can also purchase the gas ball lock adapter (KEG881), which gives you the ability to attach a gas-in disconnect directly to the filler unit. We highly recommend picking up this optional accessory!
The Tapcooler is designed to fill beer and CO2 from the bottom of the bottle through the telescoping bottle connection tube. First CO2 flows down into the bottom of the bottle to flush from the bottom up. Next you open the tap and beer flows down the same tube, filling from the bottom up. The result is a more effective purging of oxygen and little to no foam during the filling process.
The telescoping bottle connection tube allows you to fill bottles as small as 4.5" tall and up to 12.5" tall. You can fill taller bottles with the Tapcooler, but the tube will not reach the bottom of the bottle, which can lead to some splashing. When filling wide mouth containers, a bottle stopper of suitable size and with a 9 mm hole can be used as an adapter.
The filler features a push button CO2 purge valve, which allows you to purge the bottle of oxygen before and after filling. It also includes an adjustable pressure relief valve, giving you the ability to change the filling speed. The pressure relief valve also acts as an overflow port for excess beer or foam to escape when filling.
One of the best features of the Tapcooler is that it's super easy to clean. Cleaning other bottle fillers can be a chore and take lots of time. The Tapcooler comes apart easily and allows you to clean all parts effectively and easily after each use.
All metal parts that come into contact with your beer are made from 304 stainless steel. The barb and ball lock CO2 adapters are made of aluminum.
Finally, the Tapcooler comes chock full of optional accessories that will adapt your filler perfectly to your setup. See the "You Might Also Need" section below for list of accessories!
Forward-Sealing Faucet Compatibility
Tapcooler fits Intertap, Nukatap, Ultratap, Vent-Matic, and Perlick 600 series faucets. These fillers can be converted to fit Perlick 500 series with the optional tap connector (KEG887). Cannot be used with ventilated beer taps, i.e. non-forward sealing beer taps.
Features:
Hooks up directly to any forward sealing faucet for quick and easy use.
Quick setup and easy maintenance.
Perfect for bottling for competitions, sending bottles home with friends, or just to have some bottles on the go!
A range of accessories are offered for more range and easier use!
Purge bottles with CO2 before and after filling for longer lasting beer!
Pressure relief valve allows for control over filling speed and allows excess foam to escape for the perfect pour every time!
Made from 304 stainless steel
Easy to use and clean!
Leak-free quick connectors are well suited for glycol to cool fermenters.
Fits perfectly in combination with 8.5mm x 14mm EVA tubes both insulated and non-insulated.
The Brewtools Steam Condenser fits the Brewtools Steam Hat and uses cold water to cool the steam until it becomes a liquid that runs out of the condenser to a bucket or directly to the drain. The unit is an excellent alternative to a ventilation system.
The unit ships with a nozzle that supplies 1.1 liters of water per minute at 4 bar pressure. We also offer other nozzles that offers higher or lower flow depending on the water pressure where the system is used and other factors (sold separately).
Included:
TC 4" to TC 2" adapter (1 pcs)
20cm straight TC 2" pipe (2 pcs)
TC 2" Tee (1 pcs)
TC 2" Elbow (1 pcs)
TC 2" 1/8" nozzle adapter with TC34mm input (1 pcs)
TC 2" to 19mm hose barb adapter (1 pcs)
TC 2" Clamp (6 pcs)
TC 2" Gasket (6 pcs)
1/8" BSP-T nozzle, 30 degrees, 1.1 liters per minute @ 4 bar (1 pcs)
You Will Also Need:
Steam hat for your system
TC 4" Clamp and gasket
Water inlet adapter (TC34mm to hose or garden connector etc)
Outlet tube (16x25mm)
A TC34mm elbow is recommended for the water inlet
Please take not that you need much less power to keep the boil going with this device, and the risk of the wort boiling over is high when too much power is used, so make sure to take the necessary precautions. To sustain the vacuum, the drain tube from the condenser must not have any counterpressure. We recommend draining to a bucket where the tube is not submerged in the water, or suspend the tube directly over a floor drain.
For User Manuals and support, please follow this link to Brewtools Docs.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in late December.
Submersible pump for cooling applications or similar.
A perfect match for FCS to supply cooling liquids to fermentation tanks up to 50 liters.
Very quiet.
Technical Information:
Voltage: 24VDC
Maximum Power: 17W
Maximum Flow: 11 L/min / 2.9 Gal/min
Maximum Height: 4.1m / 13.5 feet
Barb Size (liquid out): Ø=10.28 mm (recommended hose size: 8x12)
Ø=0.40" (recommended hose size: 5/16" ID)
Barb Size (liquid in): Ø=14.68 mm (recommended hose size: 10x14)
Ø=0.57" (recommended hose size: 3/8" ID)
IP rating: IP68
Cable: 3m / 9.8 ft.
Connector: LP12, 2-pin plug (male)
Removable bracket with 4 suction feet is included
Connect draft tubing to your keg coupler or faucet shank. Recommended for 3/16" or 1/4" ID draft lines. Tailpiece and hex nut are made of stainless steel.
Perfect addition when purchasing a new sanke style keg coupler or tap. New taps typically come with the correct fittings for your gas line but not your beverage line. These are those fittings!
Used to connect 3/16" or 1/4" beer line.
To connect 3/16" beer line tubing it is helpful to heat the tubing end in hot water.
Unbeatable value for a homebrew counter pressure bottle filler!
Fill bottles directly from your keg with virtually no CO2 loss
Purge oxygen from bottles before filling to preserve the quality of your beer
Accessory set included for multiple connection options — no expensive add-on items needed!
Duotight connections offer unparalleled customization and adaptability to your specific needs
Compatible with forward-sealing faucets — NukaTap, Intertap, Perlick 600-series and others
Running late but don't want to leave home without a couple of bottles of your latest creation? The Nukatap Counter Pressure Bottle Filler will have your precious cargo packed and ready at the drop of a hat! Slip it right into the nozzle of your Nukatap, Intertap, or other forward-sealing faucet to fill bottles right from the tap. Gas can be quickly connected using a bare end of 8 mm OD EVABarrier tubing, or connect the included Ball Lock Adapter to hook up gas using a Ball Lock Quick Disconnect. Not enough room under your draft tower? No problem! Like the gas-in port, you can swap out the push-in spout for the Duotight adapter, allowing you to connect tubing directly to the filler, or connect a Ball Lock Post Adapter and use a Ball Lock jumper line to fill right off your keg. While other fillers on the market force you to purchase upgrade accessories to improve functionality, the Nukatap Filler gives you more options to fill right from the get-go.
This unit is designed to fill multiple sizes of beer bottles up to 500 mL thanks to the telescopic filling stem. We recommend starting with it fully extended, then insert the stem till your at the bottom of the bottle, purge the bottle with CO2, then press the stem all the way in to form a seal on your bottle.
Counterpressure filling is the absolute best option for packaging beer from your keg without affecting its quality. Filling a growler straight from the tap is always an option, but if you want your beer to be at its best when you share it with the world, this is only way to go. The Nukatap Filler will make sure your brew doesn't pick up oxygen or lose carbonation in the filling process, keeping your creation in tip-top condition
Includes:
All stainless steel counter pressure filler
Push-in spout compatible with forward-sealing faucets
(2) 8 mm Duotight adapters for filler and NukaTap spout
(2) Ball Lock Post Adapters (Red / Yellow)
19.5" length of 8 mm OD x 5 mm ID EVABarrier tubing
KegLand Part Number: KL21760
All the parts and seals you need to rebuild a keg in one convenient kit!
Includes Low2 Keg Lid O-rings that offer superior defense from oxygen ingress compared to silicone or EPDM rings
Never fear gasket failures when you go to fill your ball lock keg—this first aid kit has everything you could possibly need
Comes in a convenient, well-organized tackle box tray so you never need to go searching for that tiny replacement O-ring
Also includes tailpiece gaskets for keg couplers or draft shanks and nylon washers for KOMOS CO2 Regulators
$100 value! Save money by not purchasing all of these parts individually
The KOMOS First Aid Kit comes with all the parts needed to fully rebuild a ball lock keg and more! Don't wait for gaskets to wear down and start leaking before buying a replacement—keep this replacement part kit on hand and be ready for any situation. It's only a matter of time before keg seals fail, and when that time comes, the last thing you want to do is comb through a drawer of random gaskets for that tiny, little lifesaver. Having all your gaskets in one convenient tackle box will give you the peace of mind that you'll always be able to get your keg back in working order in no time flat.
Low2 O-rings are cutting edge blend of plastic material (Synthetic M-Class and Cross-Linked Elastomers) that provide the best protection against oxygen ingress ever seen on the homebrew market. Even in a fully pressurized, sealed keg, it's possible for oxygen to dissolve in through the gap where the keg lid and O-ring form a seal. This tiny amount of oxygen ingress over time will eventually affect all beers, but is especially detrimental to highly oxygen-sensitive beers like Hazy IPAs.
In addition to ball lock keg parts, tailpiece gaskets for draft shanks or keg couplers and regulator nylon washers for KOMOS CO2 Regulators are also included.
The Ball Lock Keg First Aid Kit also represents an incredible value and will save you a ton of money in the long run. Buying all of the parts in this kit individually would run you upwards of $100, but you can get them all in one purchase at a fraction of that price.
Includes:
(1) Ball Lock Post – Gas In
(1) Ball Lock Post – Bev Out
(2) Keg Lid O-Ring
(2) Keg Lid Pull Ring PRV
(2) CO2 Regulator Nylon Washer
(4) Keg Lid Foot
(4) Tailpiece Gasket
(6) Universal Poppet
(10) Dip Tube O-Ring
(20) Ball Lock Post O-Ring
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
MoreBeer!'s Patent Pending sparge arm design is the perfect addition to almost any all grain setup! This sparge arm assembly is made completely of stainless steel and silicone, and has two adjustment points. One of these will help to hold the sparge arm against your kettle, while the other allows you to move the sparge arm up or down inside the kettle to accommodate different amounts of grain. These adjustment knobs are very easy to hand tighten and loosen, meaning no tools are necessary. Excellent for sparging as well as recirculating your mash in a RIMS or HERMS system!
To use, simply install on your kettle wall, tighten down the stopper bumper to hold the sparge arm in place, adjust the height of the bottom disc to be right above your grain bed but below the mash tun's water level, and adjust the flow level using the included ball valve. This unit will not include a barb or quick disconnect on the inlet of the ball valve, as every brewery is different. Please choose an inlet attachment from the sparge arms recommended items. Note - This sparge arm will not fit on most coolers. Make sure to check out the video in the video tab below.
Features
100% stainless and silicone construction
Two adjustment knobs make it extremely universal
Included ball valve allows you to increase or decrease the flow rate during sparge or recirculation
Included check ball will prevent back flow
Can adjust from the top of your kettle to 12-13 inches down into your kettle
A single, large diameter outlet port trickles onto a stainless disc, which distributes sparge water gently and evenly. This port is also much easier to flush out and keep clean than many other sparge assemblies with multiple small holes that grain gets stuck in during recirculation
Stainless tube measures 18.5" from the top to the bend, and 8.5" from the bottom to the center of the distribution disc.
Can be mounted on a lip that is up to 7/8" wide
Has a 1/2" FPT ball valve
This is a complete set of gaskets to replace those inside the fill nozzles of the Marchisio Benchtop Wine Bottle Filler (WE64 / WE645). Contains 8 gaskets / seals. This seal kit is intended for the updated fill nozzles with 16mm diameter. Includes: (1) Pos 5 / Cone (2) Pos 19 (1) Pos 18 (1) Pos 13 (1) Pos 11 (1) Pos 10 (1) Pos 2
Reduced first pour foam due to low thermal mass Forward-sealing design prevents beer residue from gumming up the faucet Unique shuttle design greatly improves laminar flow, improving the pour of carbonated beverages Compatible with all Intertap faucet accessories and shanks First Pour Foam Reduction Every kegerator owner knows the letdown of pouring your first pint of the day and getting too much foam. Even with perfectly balanced draft lines, first pour foam is sometimes unavoidable simply due to the temperature of the faucet itself. Running beer through the faucet will drop the temperature, and the foaming will subside, but not without a bit of wasted beer from pouring off excess head. The NukaTap Stealth Bomber beer faucet drops to beer serving temperature much faster thanks to its lower thermal mass. Simply put, the bulkier the faucet is, the more beer is needed to flow through and chill the tap. The NukaTap is over 20% lighter than its Intertap predecessor, and even lighter still compared to other brands of faucets. Improved Laminar Flow The inspiration for the NukaTap name comes from its uniquely designed "nuke-shaped" shuttle that resides on the inside of the faucet. The NukaShuttle went through numerous rounds of redesigns and countless hours of testing to find a shape that provides superior laminar flow. This means that liquid passes by the shuttle with very little resistance, allowing highly carbonated beers or hard seltzers to pour like a dream. Sanitary Design The NukaShuttle is the world’s first seamless single-piece design. Traditional taps feature an o-ring seated on a stainless steel shuttle, which can cause a couple of issues. After many pours, the stainless shuttle rubbing against the internal body of the faucet will create small fissures that become potential infection sites, and the seated o-ring can be difficult to clean in place, making your draft cleaning and sanitizing process less effective than you realize. The NukaShuttle is an advanced TPV rubber matrix that has been seamlessly formed over a durable PP skeleton. This single-piece design eliminates the pitfalls of older manufacturing methods, making it one of the most sanitary faucets on the market. Forward Sealing vs. Rear Sealing From tap rooms to home bars, forward-sealing faucets are the ideal choice for any draft setup. In traditional rear-sealing taps, beer will drain out of the entire faucet when it's in the closed position. This means the internal mechanism is coated in beer, which then dries and becomes a sticky residue. Forward-sealing faucets, on the other hand, keep the tap full of beer so it never has a chance to dry and gunk up the internal parts. This makes the faucet much easier to clean and also reduces the chance of off flavors transferring to your beer while you pour. NOTE: The Punisher Edition faucet features a matte black body with stainless spout. Other models are pictured as example photos. For the all black NukaTap faucet, see the Stealth Bomber Edition. Faucet body & lever made from stainless steel Shuttle made from TPV O-rings made from EPDM Lever collar & friction bonnet made from brass Matte black finish / brushed stainless spout NSF approved Kegland Part Number: KL26482 Please note: this is a painted faucet and as such needs to be used, cleaned, and handled with care. Clean the faucet gently by hand and avoid tossing it into a bucket with other draft parts. Excessive soaking in caustic cleaners will damage the finish. For these reasons, we do not recommend the Punisher Edition faucets for professional settings.
Replacement white rubber gasket for Speidel variable volume tank lids.
What an upgrade to the traditional clear vinyl gaskets! Reduce issues with leakage, ensure a great seal, and reduce your worries about storing wine in a variable volume tank.These white, food-grade, rubber gaskets are formed like a channel as opposed to a circular tube to form a better seal against tank and lid. Nearly 3x as thick as the clear vinyl gaskets they also help to reduce oxidation. Hold one of these in your hand and you will instantly know from the hefty weight that this is a worthwhile upgrade for every variable volume tank owner who plans to store wine.
3/8" barb
Unsure what size gasket you need? Please see the chart below for our most popular Speidel Variable Volume Tanks.
SKU
Tank Volume
Gasket Ø
GER110VF
110L
44 cm
GER220VF
220L
55 cm
BO-063-0290
290L
63 cm
GER290VF
290L
63 cm
GER300V
300L
63 cm
GER530V
530L
82 cm
GER650VF
650L
82 cm
GER675V
675L
82 cm
GER1100V
1100L
100 cm
GER2200VR
2200L
140 cm
So handy you’ll swear this is the food-grade WD of your brewhouse!
FDA & NSF approved food grade lubricant. Great for lubricating keg parts, especially poppet valves, relief valves, and lid o-rings. Many home brewers find it helpful in sealing those rings and gaskets that have tiny leaks. Great anti-rust film for equipment which is stored outdoors. With so many uses around your brewhouse, you’ll find yourself reaching for your bottle of Silicone Spray often!
Brewtools valves are used to customize the system. All the valves have a T-type ball, which makes it close only the port opposite of the handle direction.
All the ports on the valve are 34mm TC and they are made from high quality stainless steel (SS304).
Replacement O-ring with a 25 mm diameter, designed for valves on the Foundry™ Brewing System, Stainless Bucket Fermenter, and Crucible™ Conical Fermenter across all sizes. Its durable construction ensures a perfect seal for your brewing equipment.
Replacement gasket for the ForgeFit® 1.5" butterfly valve. We recommend replacing your butterfly gasket at least every 3 years. If you wait until you have a leak, your valve has already been unsanitary for some time.
EVA-tube is perfect for glycol and other uses where the tube can't bend too much to prevent flow This insulated model is perfect for reducing condensation The tube fits 3/8" (10 mm) hose barb fittings For more information on building a cooling system for your Brewtools fermenter, click here.
NukaTap faucets offer reduced first pour foam due to low thermal mass
Forward-sealing design prevents beer residue from gumming up the faucet
Unique shuttle design greatly improves laminar flow, improving the pour of carbonated beverages
Compatible with all Intertap faucet accessories and shanks
Matte Black painted finish. See note below.
Nothing looks quite as nice as beer pouring out of a sleek, matte black draft tower. These are the same tower kits included with the KOMOS Kegerator, featuring NukaTap Stealth Bomber faucets, EVABarrier draft tubing, and Duotight push-to-connect fittings for easy assembly. The tower is made from 304 brushed stainless steel, making them corrosion resistant while also looking great!
NukaTap Stainless Faucets and Towers
These kits come with NukaTap Stealth Bomber faucets mounted on a stainless tower with matte black finish. NukaTap is the newest brand of forward sealing faucets that boast a lower thermal mass for reduced first pour foam. They feature a "nuke-shaped" internal shuttle that is made from TPV, which provides superior laminar flow to further reduce foaming issues. All faucet spout attachments and accessories are cross compatible between Intertap and NukaTap. Forward-sealing means that while in the closed position the faucet will keep beer in it instead of draining out. This keeps the internal parts from getting sticky and reduces the chance of off flavors transferring to your beer while you pour. The modular, threaded spout can fit a variety of attachments including a growler filler or stout spout.
Duotight Fittings & EVABarrier Draft Tubing
Duotight and EVABarrier have revolutionized how you connect draft line, and our tower kits come standard with both. We love Duotight push-in fittings for their quick connection, reliable seal, and versatility. Setting up and connecting draft line has never been easier -- no more hose clamps or heating water to soften tubing! Each tower comes with Duotight fittings for the tower shanks and for splitting gas lines (double & triple tap only). We recommend adding Duotight fittings to use for your keg connections as well. Depending on whether you'll be serving from homebrew kegs or commercial sanke kegs, you'll need two DUO106 or two DUO104 per line.
EVABarrier tubing has been engineered with protection in mind and is both PVC-free and BPA-free. This double walled tubing offers superior protection against oxidation, CO2 loss, and microbial growth. EVA tubing is the future of draft line for professional applications, and now your kegerator will feature the same first-class tubing.
Includes:
Stainless steel draft tower w/ Matte Black Finish
NukaTap Stealth Bomber faucet(s)
Stainless steel faucet shank(s) with Duotight tailpieces
EVABarrier gas and beverage tubing
Draft tower mounting screws
Faucet wrench
1-3 Tap Tower Dimensions:
13.4 in. tall (without faucets)
3 in. tower diameter
4.4 in. base diameter
4 Tap Tower Dimensions:
13.4 in. tall (without faucets)
4.5 in. tower diameter
Interior mounting holes (does not include bottom collar)
Please note: this is a painted faucet and as such needs to be used, cleaned, and handled with care. Clean the faucet gently by hand and avoid tossing it into a bucket with other draft parts. Excessive soaking in caustic cleaners will damage the finish. For these reasons, we do not recommend the Stealth Bomber faucets for professional settings. If you prefer a stainless steel spout that can take more punishment, the matte black towers are also sold separately and can be paired with the NukaTap Punisher Edition faucet.
Made from EPDM material, these gaskets are to replace the stock ones that come with the CPC or LinkTech High Temp Plastic 3/8" Flow Path quick disconnect fittings (our H501 Series)
Spunding valve for manual pressure setting. Adjustable from 0-2.2 bar (0-32 PSI) with a maximum deviation of 0.2 bar.
We recommend disassembling the valve and lubricating all silicone parts with silicone grease before use.
The polycarbonate glass should not be cleaned with PBW or other caustic chemicals.
This Duotight ball valve with 1/2" male thread is perfect for attaching to the water input on the Copper Counterflow Chiller (WC130), allowing you to adjust the waterflow while chilling your wort. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07375
Stainless Lock Nut. 1/4 in. Female BSPP.
BSP vs. BSPP
BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT.
KegLand Part Number: KL06507
Semi-Automatic Precision: Delivers a consistent, professional-grade seal in just 3 seconds, eliminating manual lever variability and operator error.
Universal Versatility: An adjustable platform fits standard 202 cans (12–16 oz) and can be adapted for 32 oz Crowlers or tin-plated food cans.
Durable & Safe Design: Built with rust-resistant 304 stainless steel and a low-voltage 24V DC motor for maximum safety in wet environments.
Compact Efficiency: A space-saving benchtop unit designed for easy one-person operation, making it ideal for homebrewers and nano-breweries alike.
Superior Freshness: Provides an airtight, 100% light-proof seal to prevent oxidation and keep your beverage carbonated longer than traditional bottling.
Power supply sold seprately. See below under You Might Also Need.
The Cannular Pro is a semi-automatic can seamer that is easy to use, reliable, and beautifully simple.
Whether you're a brewery looking to offer canned beer to go or a homebrewer wanting to keep your creations fresh and fully protected from light, the Cannular is the answer. This bench top unit is one of the most compact and easy to use can seamers you'll find. The Cannular only requires one person to operate, and each can takes roughly 3 seconds to seam. With a two-person team, one filling and one seaming, the Cannular becomes a suitable option for nano breweries doing small canning production runs.
The Cannular Pro guarantees a perfect, repeatable seal by automating the seaming process. By eliminating the manual lever, it removes operator variability and ensures consistent pressure for every can.
Key Features
Semi-Auto Precision: Effortless operation that delivers a uniform, professional-grade seam every time.
Universal Compatibility: Designed for all standard 202 cans, including 12 oz, 16 oz, 330 ml, and 500 ml sizes.
Adjustable Platform: Features a built-in adjustable table to accommodate various can heights—no additional spacers required.
Customizable Pressure: Easily fine-tune the platform height to ensure the ideal amount of sealing pressure for any batch.
The Cannular Pro can be adapted for use with 32 oz Crowlers (Ball 300 can/end). To seam Ball 300 end/lid type oversized aluminum cans you will need to purchase the required Chuck for 1L (32 oz) Crowlers separately (coming soon).
The Cannular Pro can also be adapted for use with Tin Plated Steel Cans for food packaging applications. The table spacer is designed to accept these 100mm cans, but you will need to purchase the required 100mm Chuck separately.
Operation:
The beauty of the Cannular lies in how truly simple it is to operate, and the semi-automatic pro model makes canning beer even easier. With only three points of operation, it only takes a few minutes to familiarize yourself with the machine. The seaming process is as follows:
Place lid atop the can and place the can on the table spacer
Turn the platform lever clockwise to raise the can to the seamer
Press the seaming operation button then wait for the can to stop spinning
Turn the platform lever counterclockwise to lower the can
That's all there is to it!
Construction:
The Cannular was designed to be compact, durable, and safe to operate in a wet environment. The platform assembly is made from 304 grade stainless steel, so no matter how messy your canning gets, there's no need to worry about rusting or degradation. The body of the unit is made from hammered sheet metal and fastened together with stainless steel screws. Rubber feet help keep the unit from slipping and sliding while in use. In addition, the Cannular features built-in brackets near the feet so you have the option to mount the machine to your counter or benchtop. The Cannular runs off of 24V DC power via the Anderson socket located on the back. This lower voltage was chosen specifically to make the unit as safe to use in a wet environment as possible.
Power:
As noted above, the Cannular comes with a 24V DC Anderson socket located on the back of the unit. It does not, however, include a cord and plug. This unit uses the more powerful Pro Model Power Supply, which provides enough power to seam tin plated steel cans as well as aluminum cans.
Why Cans?
So why can when you can bottle? There's no doubt that canning has become a more and more popular format for packaging beer among craft breweries over the last several years, and with good reason. Aluminum cans aren't just more environmentally friendly than bottles, since cans require less energy to transport and recycle, they're also much better at protecting the quality of the beer. Whereas bottles allow in light, which leads to skunking, aluminum cans offer 100% protection from UV and other wavelengths of light that are harmful to beer. There's still great debate surrounding whether cans or bottles are better at keeping beer fresh, but if done correctly, cans are theoretically the superior option. When a crown cap is crimped onto a bottle, the lining of the cap can form an imperfect seal on the bottle, allowing small amounts of oxygen in, as well as small amounts of CO2 out. Over time this can result in oxidation of the beer and lost carbonation. Seamed cans, on the other hand, form a much better seal that can prevent these issues. Of course, it's important to make sure that the can is purged of oxygen before being filled, and that the can lid is sealed atop foam to eliminate oxygen from the headspace. Aside from all the "sciency stuff", cans are just plain safer. Take your beer backpacking, camping, or poolside and rest assured that broken glass won't ruin your day!
Specifications:
Power: 250W 24V DC
Rated Speed: 3300 RPM
Gearbox Ratio: 9.8 : 1
Dimensions: 16" L x 9.5" W x 21" H
Weight: 40 lbs
Splash guard not included
Max Can Height: 7.75" (197mm)
Please note the pictured splash guard is not included with the seamer. Please see CAN106 to add the splash guard to your order.
Please note: When you receive your cannular the rollers have been set and tested at the factory. They should not need adjustment for 100,000 cans when using only Can Fresh brand cans. We recommend testing at least 4 cans to verify the calibration. The table, however, comes unadjusted and getting it set up correctly is very important to getting a proper seal. Cannular's test show that a minimum 0.4mm (.015") actual overlap is needed to seal to 90 PSI. The proper table tension takes a little practice and you can expect to waste a few cans getting it dialed in. Once you learn the proper tension re-adjusting it is very quick and easy. You want the tension to be tight but not so tight as to dent the can. Use cans at your fill height with water for proper tension adjustment.
KegLand Part Number: KL15769
Cannular Compact Semi-Auto Canning Machine | User Guide
An Intertap accessory that converts the spout of an Intertap faucet into a ball lock quick disconnect. One of the most popular uses is being able to connect the beverage side of your counter pressure filler without having to open your refrigerator door.
Compatible with Intertap and NukaTap faucets.
Stainless Steel Construction
Kegland Part number: KL01052
Made by MoreBeer! from 304 stainless steel.
This quick disconnect seals up very well without a lot of work in connecting them. This will work with any of our H503 and H507 series of quick disconnects. However, it does not work in conjunction with any of our plastic or brass quick disconnects. These feature a 1/2" Barb on the ends for easy connectivity to any 1/2" tubing you may have.
The quick disconnect will hold pressure for typical brewing applications when moving liquids at 60psi or less. 3/8" ID. Gasket temperature range is -40° to 250° F. Open port, does not have shut-off.
We designed the original stainless QD's for the brewing industry over 10 years ago. The same manufacturer has been machining them for us ever since. The design has certainly been copied but not with consistent quality. That is why MoreBeer! Stainless QD fittings have a near unanimous 5 star review.
Please Note: This product will NOT work with our Brass or Plastic Quick Disconnects.
Adjustable relief valve installs on standard ball lock keg posts Use with any ball lock keg to control flow during closed pressure transfers Integrated pressure gauge can be swapped out with a digital gauge or large face dial gauge for easier, more accurate readings Adjustable black cap can be swapped out for color coded PRVs with a fixed pressure Low-profile design only measures 1.75" in height This easy to use and compact pressure relief valve is super handy for keg transfers. Using a ball lock quick disconnect as the main body, the valve easily snaps onto ball lock keg posts. Adjustable relief valves are a great way to limit oxygen exposure and regulate flow during closed keg transfers, The included gauge reads from 0-30 PSI and can be swapped out with a digital gauge or large face dial gauge for easier, more accurate readings. The black pull ring cap on the other end can be rotated for adjustments, or swapped to a range of color coded PRVs for a fixed pressure. This low-profile option only measures 1.75" in height. It works right out of the box but has several upgrade options as shown in the images. Warning: Never swap out the valve's standard PRV with a color coded PRV that exceeds the pressure rating of your vessel. Features: Duotight fitting where the gauge attaches This allows for upgrading the valve with a digital gauge or larger analog gauge Manual pull ring pressure relief This allows for you to not only adjust the pressure with the black rotary knob but also use the ring pull to instantly release pressure if you want to release manually Option for several color coded PRVs to be used (see below) Yellow - 17 psi Red - 35 psi Green - 65 psi Gray - 100 psi KegLand Part Number: KL29438
The highest quality plastic ball lock quick disconnect available to homebrewers
Smooth operation—clicks into place on keg posts and is easily removed
Built-in flare washer—no need for a separate nylon washer that is required with stainless steel QDs
CMBecker is an international manufacturer of beverage dispensing solutions for both home and professional draft equipment
Gray plastic clearly identifies the disconnect as the gas in QD
This white, beverage out quick disconnect comes with a barb for attaching to a gas line, and it's made by CM Becker so you know it is high quality.
1/4" flare connection.
Note: Sometiems ball lock fittings can be difficult to get fully seated on a Cornelius keg. We recommend using a quick spray of sanitizer solution to act as a lubricant and giving it a few twists while applying the ball lock.
The highest quality plastic ball lock quick disconnect available to homebrewers
Smooth operation—clicks into place on keg posts and is easily removed
Built-in flare washer—no need for a separate nylon washer that is required with stainless steel QDs
CMBecker is an international manufacturer of beverage dispensing solutions for both home and professional draft equipment
Black plastic clearly identifies the disconnect as the liquid out QD
This black, beverage out quick disconnect comes with a flare for attaching to a beverage line, and it's made by CM Becker so you know it is high quality.
The flare threads measure 1/4 inch.
Note: Sometimes ball lock fittings can be difficult to get fully seated on a Cornelius keg. We recommend using a quick spray of sanitizer solution to act as a lubricant and giving it a few twists while applying the ball lock.
