Made of food grade plastic, this 12 gallon wine fermenter is great for grapes and will hold around 75 lbs of must.
Dimensions: 21” tall x 15” wide at top tapering to 12.5 at bottom.
Wide mouth carboys are the easiest glass fermenter to clean with plenty of room to get your arm inside to scrub
Add bagged flavoring additions and remove them freely when finished—this can be nearly impossible with traditional narrow neck glass carboys
Watch fermentation activity as it's happening! The ultimate advantage of translucent glass or plastic fermenters
Ported lid with removable cap sized for a #5 stopper & airlock
Carrying harness included for easier handling
Glass carboys have been a staple of the brewing and winemaking world for generations, but traditional tight neck carboys aren't without their limitations. Standard glass carboys can be difficult to clean after fermentation. The wide mouth carboy is extremely easy to clean—simply removing the lid allows you to get your hand or arm all the way inside to scrub away stubborn sediment.
Each carboy comes with a carrying harness.
Features:
Gasketed lid for tight seal
Included carrying harness
Ported lid ready for #5 stopper & airlock
165mm (6.5") lid opening
Continuous thread, 5mm pitch
Dimensions
Size
Diameter
Height
5L
7.9"
10.2"
9L
8.9"
12.2"
15L
10.4"
14.2"
23L
11.8"
16.5"
26L
12.4"
17.3"
Please note: The carrying harness should not be used to move the vessel when full. The airlock lid is primarily recommended for short fermentations.
This stainless steel thermowell is your best option of monitoring temperatures in the 27L or 55L FermZilla. Since the thermowell installs into the lid, the thermowell will be well positioned in the middle of the fermenter to provide an accurate core temperature reading. On the bottom side of the FermZilla's lid you'll find several convenient drill locations already molded into the plastic. The thermowell is long enough to work with either size FermZilla (or other fermenters!), so if you need to cut the tube down a bit, we recommend using one of these Pipe Cutters. The FermZilla will still be pressurizable after installing the thermowell, just be careful to drill the hole no wider than needed to fit the Duotight bulkheads. 23.6" long (60 cm) 5/16" OD (8 mm) 1/4" ID (7 mm) Made from 304 stainless steel Kegland Part number: KL14649
Ferment under pressure with precisely tuned pressure settings
Pressure fermentations help to suppress unwanted esters
Make clean lagers faster and at higher temperatures
Easy-to-read etched pressure scale from 15 to 30 psi
Hand adjustable—turn clockwise or counterclockwise to raise or lower your setting
Made from 304 stainless steel with polycarbonate cylinder
MB is a brand dedicated to crafting and sourcing high-quality, professional-level brewing supplies
The MB T.C. spunding valve will give you the highest level of accuracy when fermenting under pressure. Designed for use with any pressurizable stainless steel conical with 1.5" T.C. top ports. For larger units, the spunding valve can also be integrated into the blowoff pipework and used with a pressure gauge and tri-clamp tee. The polycarbonate cylinder that surrounds the spunding valve can be filled with water or sanitizer to keep your tank 100% sanitary throughout the fermentation process.
Adjustable from 15-30 psi
Made from 304 stainless steel
11.75" H x 4" Ø
For Your Safety: Never exceed the maximum rater working pressure of your vessel at any time during operation. The fixed-pressure PRV on your conical should always remain in place while using this spunding valve.
US-05 produces clean and crispy ales with a well-balanced, neutral character
Stays in suspension during fermentation for great attenuation
Highly recommended for American ales and highly hopped beers
Fermentis active dry yeast offers reliability, ease-of-use, and consistency to home and professional beverage makers across the world
Formally US-56, US-05 is a strain of yeast that creates that classic American profile of clean malt, crisp taste, low diacetyl, and ability to ferment in a wide range of temps. Look for US-05 to be the next popular dried yeast.
This yeast can be pitched directly, but if you prefer to rehydrate, the instructions are below.
Sprinkle the yeast in a minimum of 10 times its weight of sterile water or wort (we suggest 4 oz) at 70°F to 77°F (21 to 25 °C). Do not stir. Leave to rest 15 to 30 minutes. Gently stir for 30 minutes, and pitch the resultant cream into the fermentation vessel.
Attenuation: 78-82%
Sedimentation Time: Medium
Alcohol Tolerance: 9-11% ABV
Optimum Fermentation Temp: 64-78°F
*See the technical data sheet below for more information on rehydration, usage and storage.
Made in Italy, these are premium glass carboys are set apart from others because the glass has a more uniform thickness with less inclusions. Inclusions, or internal defects, occur when the glass is not cooled slowly over a longer period of time. This 6 gallon size works great as a primary fermenter for beer, wine and mead.
Our line of Itailan carboy is our top recommendation for glass carboys.
Specifications:
Weight: 14.0 pounds each
Dimensions 21" x 11"
Country of origin: Italy
With the FermZilla Pressure Kit you can ferment under pressure, carbonate, and serve without ever needing to move your beer out of the fermenter. The kit inlcudes two stainless female threaded ball lock fittings with barbs, which thread onto the existing openings atop the FermZilla's lid. For the beverage out, you'll have a silicone dip tube with stainless steel float, allowing you to always draw from the clearest beer at the top of the tank. Pick up the Pressure Kit and turn your FermZilla into a true unitank! The silicone dip tube is 31" long. It will work perfectly as is for the 55L FermZilla. For the 27L model we recommend cutting the dip tube shorter to remove unwanted slack. With the optional Floating Dip Tube Filter, you can prevent hop material and other solids from ever entering the dip tube. Especially handy when you're pulling samples mid-fermentation! Fermenting Under Pressure:
The pressure kit allows for fermenting under pressure, which will reduce esters and fusel alcohol production. This means you can ferment at warmer temperatures than you normally would, even making lagers at room temperature. Most commerical beer is fermented under pressure simply due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the distinct differences between homebrewing and brewing on a commercial scale. The FermZilla's lid already comes with a built-in pressure relief valve that will blow at 35 psi; the pressure kit simply allows you to add CO2 through the ball lock fitting. We strongly recommend that you also purchase an adjustable pressure relief valve, or spunding valve, which allows you to set a lower pressure. It's always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure. Carbonating, Transferring, and Serving:
When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using a spunding valve. This means you can eliminate kegging and serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Attach a beer line from the FermZilla's bev out to your keg and enjoy the easiest kegging experience ever. You can also choose to send carbonated beer through a beer filter on the way to your keg. When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator. Eliminate Oxidation:
Since the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock. Key Features:
Ferment beer under pressure to reduce ester and fusel alcohol production Always draw clear beer with the floating dip tube Keg beer that has already been carbonated Use CO2 to push beer into a keg or through a filter into a keg Eliminate kegging altogether by carbonating and serving directly from the FermZilla Installation Note: For best performance, ensure there is not an excess amount of slack when the silicone dip tube is installed and shorten it if needed. With the floating dip tube installed on your empty FermZilla, you ideally want the dip tube to hang freely with just enough length for the end of the dup tube to touch the bottom of the tank. Please note: pressure kit does not include the lid pictured in the example photo. The ball locks and floating dip tube are installed on the FermZilla's existing lid.
Dual purpose hops popularly used in American styles including Pale Ales and West Coast IPAs
Aroma Profile: Citrus, Tropical, Floral, Grapefruit, Grassy, Herbal, Pine
Alpha Acids: 4.5 – 7.0%
Whole cone hops are often preferred for dry hopping as they maintain contact while floating in the beer and are easier to remove
Adding whole cone hops directly to the mash tun is a great way to add flavor and help clarify wort
Cascade is the classic American hop that really started the hop craze. Defined by its citrus, and often more specifically, grapefruit flavor it is now sought out around the World. It is a true dual-purpose hop that can be used for bittering, at the end of the boil, or the fermenter. Used in so many craft brewed pale ales, but none more famous than Sierra Nevada's Pale Ale. You cannot go wrong using Cascade in all kinds of American style ales.
Whole cone hops are typically the preferred format for dry hopping as they maintain contact with the beer by floating, they are easier to remove than pellets and they add a unique character to the beer. Adding whole hop cones directly to the mash tun is also a great way to add an extra layer of hop flavor and to clarify your wort as it filters through the flowers.
Hop Statistics:
Alpha Acids: 4.5 – 7.0%
Beta Acids: 4.5 – 7.0%
Alpha-Beta Ratio: .64 – 1.55
Cohumulone: (% of alpha acids): 33 – 40%
Total Oils in mls per 100 grams dried: 0.8 – 1.5
Storage (% alpha acids remaining after 6 months storage at 68° F): 48 - 52%
Similar Hop Varieties: Ahtanum®, Centennial, Amarillo® hops
Ahtanum® is a registered trademark owned by Yakima Chief Hops, LLC.
Amarillo® is a trademark owned by Virgil Gamache Farms, Inc.
With the FermZilla Pressure Kit you can ferment under pressure, carbonate, and serve without ever needing to move your beer out of the fermenter. The kit inlcudes two plastic female threaded ball lock fittings with barbs, which thread onto the existing openings atop the FermZilla's lid. For the beverage out, you'll have a silicone dip tube with stainless steel float, allowing you to always draw from the clearest beer at the top of the tank. Pick up the Pressure Kit and turn your FermZilla into a true unitank! Includes one red and one yellow ball lock cap to help differentiate which one is being used for liquid and which one for gas. Either color can be used for either function. The silicone dip tube is 31" long. It will work perfectly as is for the 55L FermZilla. For the 27L model we recommend cutting the dip tube shorter to remove unwanted slack. With the optional Floating Dip Tube Filter, you can prevent hop material and other solids from ever entering the dip tube. Especially handy when you're pulling samples mid-fermentation! Fermenting Under Pressure:
The pressure kit allows for fermenting under pressure, which will reduce esters and fusel alcohol production. This means you can ferment at warmer temperatures than you normally would, even making lagers at room temperature. Most commerical beer is fermented under pressure simply due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the distinct differences between homebrewing and brewing on a commercial scale. The FermZilla's lid already comes with a built-in pressure relief valve that will blow at 35 psi; the pressure kit simply allows you to add CO2 through the ball lock fitting. We strongly recommend that you also purchase an adjustable pressure relief valve, or spunding valve, which allows you to set a lower pressure. It's always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure. Carbonating, Transferring, and Serving:
When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using a spunding valve. This means you can eliminate kegging and serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Attach a beer line from the FermZilla's bev out to your keg and enjoy the easiest kegging experience ever. You can also choose to send carbonated beer through a beer filter on the way to your keg. When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator. Eliminate Oxidation:
Since the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock. Key Features:
Ferment beer under pressure to reduce ester and fusel alcohol production Always draw clear beer with the floating dip tube Keg beer that has already been carbonated Use CO2 to push beer into a keg or through a filter into a keg Eliminate kegging altogether by carbonating and serving directly from the FermZilla Installation Note: For best performance, ensure there is not an excess amount of slack when the silicone dip tube is installed and shorten it if needed. With the floating dip tube installed on your empty FermZilla, you ideally want the dip tube to hang freely with just enough length for the end of the dup tube to touch the bottom of the tank. Please note: pressure kit does not include the lid pictured in the example photo. The ball locks and floating dip tube are installed on the FermZilla's existing lid.
Heavy-duty HDPE plastic fermentation and stoarge tank
Made from food-safe materials with extra thick walls to preserve the aroma of your beverage
Rotating plastic spigot eliminates the need to use an auto-siphon or racking arm to transfer liquid
Wide top port opening for easy cleaning
Airlock & stopper included
Made in Germany by Speidel
The future is here today, and the future is HDPE Fermentation & Storage Tanks from Speidel. Made in Germany from nothing but undyed and food-safe plastic, these tanks are produced with particularly thick walls which preserves the aroma and the alcohol for a markedly long time. The stable carrying handles have been tried and tested for decades and are extremely durable.
Are you tired of carboys? Hate siphoning to transfer? Wish you could ferment larger batches in a single container? Sick of lifting 50lbs by a small metal handle? Done with worrying about shattered glass, injury and lost product? Well then have we got the solution for you!
These heavy duty plastic tanks offer a fantastic fermentation & storage solution at a great price.
Key Features:
Heavy duty HDPE construction is durable and resists oxygen transfer. None of the risks of working with glass.
Small footprint and rectangular shape makes them easy to store - take better advantage of the space you have to dedicate to wine & beer making.
Large lid opening makes them easy to clean by hand - say goodbye to your carboy brush!
All ports seal with gaskets and the vessel can be fully sealed for long-term storage.
Includes a spigot and oversized 2-piece Speidel airlock.
Designed and manufactured in Germany by Speidel, the makers of our legendary commercial wine tanks
32"L x 22"W x 32"H, 19.84 lbs
FAQ:
Can filled containers be carried by the handles?
Depending on the weight—barrels up to 30L are no problem—60L is the limit and should not be carried when completely full. The handles have a weight capacity of 30kg (66 lbs).
Is there an upper limit on the alcohol content of the stored liquid?
In principle, there is not. However, it should be noted that the higher the alcohol content, the faster the seals and, to a lesser extent, the tank itself will wear out.
Up to what temperature can the containers be used?
For short periods of time the containers can withstand temperatures of up to 80°C (176°F). This temperature should not be exceeded. For longer periods of time the containers can be used at temperatures up to 60°C (140°F).
The KOMOS Double-Wide Kegerator has the largest interior capacity of any home kegerator on the market. With an extra wide design, this unit can hold up to eight 5-gallon Slimline Torpedo Kegs or Pepsi-style Ball Lock Kegs. This version does not include a tower kit. Great as a fermenation refrigerator or as a unit that can be built-in when adequate ventilation is an option. Approximately 2-3" of space on each side of the kegerator is required to allow the unit enough air. The tower is then mounted to the countertop and often a pvc collar or foam insulation is placed between the kegerator and the counter. This can also be done with any of our regular kegerators by removing the tower from the unit and mounting it on the counter. Other features you'll love about the KOMOS Kegerator include its highly-efficient cooling capacity so you'll be serving ice cold beer even in the warmest temperatures, extra wide temperature range from 26–82°F, dual gas inlets at the back, aluminum internal floor, rolling casters, and the included KOMOS Dual Gauge CO2 regulator.
The most eye-catching difference between the KOMOS Double-Wide and other kegerators is definitely the capacity. With an extra wide interior and double tower configuration, this is likely the only home kegerator you'll find that can hold up to eight 5-gallon Slimline Torpedo or Ball Lock Corny kegs.
Dual gas line inlets are absolutely clutch if you want to serve beverages at two different pressures or use two different types of gas. Many kegerators only have one inlet that is only wide enough for a single line to pass through. Both inlets on the back of the KOMOS unit are just over 3/4" in diameter and feature PCO 1881 threads. This threading allows you to use the plastic Carbonation Ball Lock Cap (FE13) as a quick connect option for your gas lines.
Upgraded condenser, evaporator, and insulation make this unit highly efficient, yet quiet, so you can serve ice cold beer in even the warmest temperatures. The unique internal fan provides excellent air circulation, pulling cold air from below the evaporator and blowing it back over the top of your kegs and up into the towers to chill your draft lines.
Extra Wide Temperature Range is Perfect for Homebrewers
The KOMOS kegerator is tailored to a homebrewer's needs. Take, for example, the extended range digital controller with an adjustable temperature range from 26 - 82°F. This allows homebrewers to use as fermentation chamber and is something that other kegerators don't do. Although the unit does not provide heating, the extended range allows you to program the internal temperature at say an ale fermentation temp of 68°F and will provide cooling whenever the temp rises above that set point. With the insulation provided by the kegerator, heating should rarely be needed, but you can always place a low wattage heat wrap inside the unit if ever needed. The digital controller always displays the temperature and is easily adjusted from the front of the kegerator with the door closed. It's pretty nice.
KOMOS Regulator
The included high quality KOMOS regulator maintains consistent pressure. The regulator includes a blow-off PRV with pull ring for safety and relieve pressure, rubber coated gauges, and a hand knob for easy adjustment. Included with your kegerator package is a Duotight fitting that attaches to the regulator for an easy, solid, push-to-connect connection with your gas line.
Added Features
One of the unique features on a kegerator in this price range is the tower fan, which blows cold air up into your tower to reduce foaming issues. They also come standard with the KOMOS dual gauge CO2 regulator, which is super beefy and consistent in delivering accurate pressures. Most Chinese-made regulators experience creep where the pressure increases over time. The KOMOS regulator is by far the best CO2 regulator we have seen made in China.
The countertop drip trays couldn't be easier to keep clean. Built-in drip trays look cool, but they're a pain to keep clean. Before long they get pretty disgusting with dried, spilled beer -- attracting fruit flies and becoming a haven for mold and bacteria to grow. They'll often overflow the reservoir inside the kegerator causing a huge mess. Our kegerator's tray is designed to be removed and easily washed.
Best Value & Backed by MoreBeer!
We've looked around, and when you factor in fast and free shipping, you are getting the very best value on a kegerator in the USA. Plus you're getting MoreBeer! service if something happens in shipment, however unlikely since these units require freight shipping. If your unit arrives damaged just call us up and we will work with you to take care of it.
Feature Summary:
Digital Thermostat with wide 26 - 82° F temp range.
Robust KOMOS Dual Gauge Regulator included
CO2 Tank holder mounts on back of kegerator (tank not included)
Efficient and powerful compressor
Stainless Steel Door
Countertop Style Drip Trays
Aluminum floor for additional keg support
Rolling casters
You will need to purchase keg connections depending on whether you are serving commercial sanke, ball lock corny, or pin lock corny
Specifications:
35.4" wide
27.8" deep
34.3" with CO2 mount
33" Tall (fridge only)
35.5" with Caster wheels
110V - 50 hz
0.9 Amp draw
Optimal ambient temperature is 65°F – 80°F
CSA Certified
Internal Dimensions:
31.6" wide
20.4" deep
17.1" on the left side where the compressor sits
28.3" tall
What Fits:
5 Gal. Torpedo Keg - 6
5 Gal. Slimline Torpedo Keg - 8
6 Gal. Torpedo Keg - 6
5 Gal. Megamouth Torpedo Keg - 3
5 Gal. Pin Lock Cornelius Keg (Corny Keg) - 6
5 Gal. Ball Lock Cornelius Keg (Corny Keg) - 8
5.2 Gal. Oxebar PET Keg - 6
5.16 Gal. Sixth Barrel Keg (Sixtel, Log) - 6
7.75 Gal. Quarter Barrel Keg (Pony Keg, Stubby Quarter) - 1
7.75 Gal. Slim Quarter Keg (Tall Quarter, The Slim) - 3
15.5 Gal. Half Barrel Keg (Full Size Keg) - 2
See below for the Kegerator Instruction Manual.
Please note: This unit requires 4" of clearance on all sides and is not intended to be installed under a countertop. For a build-in unit, see the KOMOS Pro Stainless Steel Kegerator.
Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high end fermentation tanks with new features and a lot of possibilities. Key Features: Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation. Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a spiral. Many options for connecting accessories like sensors, heaters, carb. stones and other accessories. Pressure rated for 2 bar / 30 PSI Cooling jacket pressure rated for 0.5 bar / 7 PSI 8" TC port on top for easy access. 2" TC dump and racking valves. BrewTools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Low height w/o acc.: 50" Max height w/o acc.: 57.9" Packaging size: 51.2" (h) x 23.6" (w) x 23.6" (d) Net weight: 123.5 lbs Gross weight: 136.5 lbs Tank diameter (inside): Ø19.7" Gross volume: 41.7 gal Max rec. volume: 40 gal Min rec. volume: 10.5 gal Volume, cone: 6.3 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2.0 bar / 30 PSI In the box: Unitank with adjustable frame 1 pcs Analog pressure gauge, TC34mm 2 pcs Butterfly-valve, 2" 1 pcs Butterfly-valve, 34mm DN20 1 pcs Blow-off pipe 1 pcs Racking arm 2" 1 pcs TC elbow 90°, 2" 1 pcs Insulation jacket, black neoprene 1 pcs Sample valve, 34mm 1 pcs TC Adapter 8"-4" 1 pcs TC blind cap, 4" 1 pcs TC blind cap 2" 2 pcs TC blind cap 1.5" 3 pcs TC blind cap 34mm 2 pcs TC gasket 8" lipped 2 pcs TC gasket 4" 2 pcs TC gasket 2" 5-pack 1 pcs TC gasket 1.5" 5-pack 3 pcs TC gasket 34mm 5-pack (DN20) 1 pcs Tri Clamp 8" 1 pcs Tri Clamp 4" 5 pcs Tri Clamp 2" 2 pcs Tri Clamp 1.5" 10 pcs Tri Clamp 34mm 1 pcs TC tool 4 pcs M10 steel/rubber feet 1 pcs TC34mm safety valve (PRV, 2 bar) Necessary bolts and parts for assembly 5 year manufacturer's warranty
Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, etc. For User Manuals and support, please follow this link to Brewtools Docs. NOTE: Model in photo is a prototype. Minor changes and improvements may occur.
Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high end fermentation tanks with new features and a lot of possibilities. Key Features: Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation. Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a spiral. Many options for connecting accessories like sensors, heaters, carb. stones and other accessories. Pressure rated for 2 bar / 30 PSI Cooling jacket pressure rated for 0.5 bar / 7 PSI 8" TC port on top for easy access. 2" TC dump and racking valves. BrewTools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Low height w/o acc.: 66.1" Max height w/o acc.: 74" Packaging size: 70.8" (h) x 28.3" (w) x 28.3" (d) Net weight: 167.1 lbs Gross weight: 209.4 lbs Tank diameter (inside): Ø23.6" Gross volume: 81.8 gal Max rec. volume: 76.6 gal Min rec. volume: 31.7 gal Volume, cone: 10.5 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2.0 bar / 30 PSI In the box: Unitank with adjustable frame 1 pcs Analog pressure gauge, TC34mm 2 pcs Butterfly-valve, 2" 1 pcs Butterfly-valve, 34mm DN20 1 pcs Blow-off pipe 1 pcs Racking arm 2" 1 pcs TC elbow 90°, 2" 1 pcs Insulation jacket, black neoprene 1 pcs Sample valve, 34mm 1 pcs TC Adapter 8"-4" 1 pcs TC blind cap, 4" 1 pcs TC blind cap 2" 2 pcs TC blind cap 1.5" 3 pcs TC blind cap 34mm 2 pcs TC gasket 8" lipped 2 pcs TC gasket 4" 2 pcs TC gasket 2" 5-pack 1 pcs TC gasket 1.5" 5-pack 3 pcs TC gasket 34mm 5-pack 1 pcs Tri Clamp 8" 1 pcs Tri Clamp 4" 5 pcs Tri Clamp 2" 2 pcs Tri Clamp 1.5" 10 pcs Tri Clamp 34mm 1 pcs TC tool 4 pcs M10 steel/rubber feet 1 pcs TC34mm safety valve (PRV, 2 bar) Necessary bolts and parts for assembly 5 year manufacturer's warranty
Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, etc. For User Manuals and support, please follow this link to Brewtools Docs. NOTE: Model in photo is a prototype. Minor changes and improvements may occur.
Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high-end fermentation tanks with new features and a lot of possibilities. Key Features: Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a coil Many options for connecting accessories like sensors, heaters, carb. stones and other accessories Pressure rated for 2 bar / 30 PSI Cooling jacket pressure rated for 0.5 bar / 7 PSI 8" TC port on top for easy access 2" TC dump and racking valves Brewtools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Low height w/o acc.: 43.3" Max height w/o acc.: 51.2" Packaging size: 44.5" (h) x 20.5" (w) x 20.5" (d) Net weight: 99 lbs Gross weight: 110 lbs Tank diameter (inside): Ø15.75" Gross volume: 22.7 gal Max rec. volume: 21.1 gal Min rec. volume: 5.3 gal Volume, cone: 3.1 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2.0 bar / 30 PSI In the box: Unitank with adjustable frame 1 pcs Analog pressure gauge, TC34mm 2 pcs Butterfly-valve, 2" 1 pcs Butterfly-valve, 34mm DN20 1 pcs Blow-off pipe 1 pcs Racking arm 2" 1 pcs TC elbow 90°, 2" 1 pcs Insulation jacket, black neoprene 1 pcs Sample valve, 34mm 1 pcs TC Adapter 8"-3" 1 pcs TC blind cap, 3" 1 pcs TC blind cap 2" 2 pcs TC blind cap 1.5" 3 pcs TC blind cap 34mm 2 pcs TC gasket 8" lipped 2 pcs TC gasket 3" 2 pcs TC gasket 2" 5-pack 1 pcs TC gasket 1.5" 5-pack 3 pcs TC gasket 34mm 5-pack (DN20) 1 pcs Tri Clamp 8" 1 pcs Tri Clamp 3" 5 pcs Tri Clamp 2" 2 pcs Tri Clamp 1.5" 10 pcs Tri Clamp 34mm 1 pcs TC tool 4 pcs M10 steel/rubber feet 1 pcs TC34mm safety valve (PRV, 2 bar) Necessary bolts and parts for assembly 5 year manufacturer's warranty
Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, etc. For User Manuals and support, please follow this link to Brewtools Docs. NOTE: Model in photo is a prototype. Minor changes and improvements may occur.
Our mini and medium 2-piece airlocks are a great option when a single inch could make or break fitting your carboy into a fermentation chamber. The airlock breaks down into 2-pieces for easy cleaning. Instead of a floating center piece, like standard 3-piece airlocks, the center piece is molded into the lid. One less piece to clean and misplace!
Another cool feature of this 2-piece airlock is that 1/2" ID tubing will fit onto the center post for use as a blowoff. This can be handy if you have a really active ferment that is blowing out the top of your fermenter.
Holds approximately 0.4 fl oz (12 ml)
Chamber - 1-1/2" tall x 1-3/8" diameter
Stem - 1" long
Stopper not included
TF-6 is ideal for maximizing the fruitiness of your cider
Very high aromatic intensity and complexity towards fresh fruity notes
Sweet and round mouthfeel strengthening candy like sensation
Fermentis active dry yeast offers reliability, ease-of-use, and consistency to home and professional beverage makers across the world
The best cider yeast for a very high aromatic intensity and complexity towards fresh fruity notes (apple, banana-pear, red, citrus and exotic fruits) combined with interesting elaborated fruit notes (applesauce).
Usage:
For sweet ciders, sweet and round mouthfeel strengthening candy like sensation.
Technical Characteristics:
Regular slow kinetic
Broad fermentation temperature spectrum: 10-30°C (50-86°F), ideally 15-25°C (59-77°F).
High nitrogen requirements: Ratio YAN**(mg/L)/Sugar(g/L) > 0.9
Medium assimilation of fructose
Maximum initial SO2 level recommended: 50mg/L. Very low production of acetaldehyde and SO2
High malic acid consumption (up to 1.4g/L)
Medium 2-phenylethanol and very high isoamyl acetate (candy-banana) producer
Dosage:
20 to 40 g/hl for first fermentation
Direct inoculation:
Pour the yeast on the surface of at least 10 times their weight of must (possibly directly on the top of the tank or during tank filling after clarification).
Gently stir to avoid or break clumps.
Immediately transfer into the tank via a pumping over with aeration (or homogenize tank volume).
With prior rehydration:
Pour the yeast on the surface of 10 times their weight of tap water at room temperature.
Gently stir to avoid or break clumps.
Wait for 20 minutes and transfer into the tank via a pumping over with aeration.
Shelf Life:
4 years from production date.
This airlock made from polypropylene is much less rigid and less likely to crack compared to standard three-piece airlocks. Toss it into a bucket of sanitizer with your other equipment and don't worry about it breaking. Airlocks are another one of those necessary pieces of equipment for every homebrewer. If you ferment in a carboy or bucket this 3 piece airlock is a must! It’s a popular alternative to the triple ripple type of airlock because it can be taken apart and cleaned, and is easy to fill. (However we do sell the triple ripple type (FE371) in case you are used to that type and would like to stay with it.) While a simple device not all airlocks are the same. Some other designs have only a couple holes in the plastic lid and this can cause the airlock to pop out during an active fermentation. Our design features multiple holes that allow CO2 to escape easily. Additionally, some other airlocks have a cross hatch design on the bottom. We have found this more easily leads to Krausen clogs and the airlock being pushed out of the fermenter. Ours is open, allowing Krausen foam to enter the airlock if necessary. Better to clean your airlock out than to find it laying on the floor next to your fermenter 3 days later. Another cool feature of this 3-piece airlock is that 1/2" ID Silicone tubing will fit onto the center post for use as a blowoff. In the cases where you are using a yeast known to produce lots of Krausen (WLP002 from White Labs or 1968 from Wyeast for example) remove the top cover, remove the plastic 'hat', and install the silicone tubing. Run the silicone tubing into a jar or bucket of water. When fermentation dies back down remove the tubing and replace the hat and cover. Please Note: Airlock only - stopper not included. KegLand Part Number: KL01595
K-97 is ideal for delicate beers like Kolsch, Wits and Session Beers as well as heavily hopped beers
Tends to present floral and balanced fruity character depending on fermentation conditions
Fermentis active dry yeast offers reliability, ease-of-use, and consistency to home and professional beverage makers across the world
The perfect dry yeast for your German ales or Belgian-style wheat beers. K-97 is selected for its penchant to form a large, firm krausen while fermenting. A great choice for ales that you want to have a low ester character. The lower attenuation of K-97 makes for beers with a nice mouthfeel. Can ferment anywhere between 54-77°F, although the ideal range is between 59-68°F.
This yeast can be pitched directly, but if you prefer to rehydrate, the instructions are below.
Sprinkle the yeast in a minimum of 10 times its weight of sterile water or wort (we suggest 4 oz) at 70°F to 77°F (21 to 25 °C). Do not stir. Leave to rest 15 to 30 minutes. Gently stir for 30 minutes, and pitch the resultant cream into the fermentation vessel.
Attenuation: 80-84%
Sedimentation Time: Slow
Alcohol Tolerance: 9-11% ABV
Optimum Fermentation Temp: 64-78°F
*See the technical data sheet below for more information on rehydration, usage and storage.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
Oxygenate your wort like the pros with the OxyWand Oxygenation kit! Insert the oxygenation wand into your fermenter and pump in thousands of microscopic oxygen bubbles for 1-2 minutes to improve the health of your yeast. Healthy yeast produce amazing flavors and have the stamina to completely finish fermentation.
That is not the only reason yeast love the OxyWand™. Yeast hate to compete with bacteria and you hate to drink them. Sintered stainless stones are made of tightly compressed stainless steel powder to create a porous block through which oxygen can flow. This micro maze is also the perfect environment for bacteria to live in after the stone has been used once in wort. That is why we love to boil our stones prior to use. The stone on the OxyWand™ is connected via a 1/4" flare fitting and can easily be removed and cleaned after use and then boiled before your next brew day.
This OxyWand™ Oxygenation kit comes complete with adjustable brass oxygen regulator, Sanitary air filter, 4 ft of tubing, Instructions, and a 26" long 0.5 Micron OxyWand™.
The advantage of using compressed oxygen to oxygenate is speed - you can oxygenate your wort in 60 seconds as opposed to 30-120 minutes with aeration. This .5 micron stone can only be used with compressed oxygen because an aeration pump does not supply enough pressure. If you are looking for an Oxywand to use with aeration pumps please see the 2 micron version.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
Premium quality laser-welded 304 stainless steel closed tank
Made in Germany by Speidel and backed by a 25-year warranty
Ideal for spirits and fermented beverages like wine, beer, cider, and kombucha.
Ultra-smooth 2R interior finish allows for easy cleaning with cold water
Outfitted with a 6-bar max cooling jacket for efficient glycol cooling
1.5” tri-clamp ports with two additional DIN ports for included thermometer/thermowell combo and sample valve
The top lid provides a convenient opening for additions and the legs provide easy access to the bottom ports
Vaulted complete drainage bottom for maximum product yield and easy cleaning
We are proud to present these FD storage tanks made of premium quality 304 stainless steel. Built in Germany by Speidel and sold exclusively in the USA by MoreWine! Pro for over 20 years, the world-class traditions of German engineering and craftsmanship are reflected in these tanks. And, after examining tanks built by every major manufacturer worldwide, we can safely say that when it comes to features, quality, and price, these tanks represent the very best value available in stainless steel beer storage.
Safely store small volumes of product in these beautiful tanks. The legs make accessing the ports easy and the convenient top hatch makes cleaning a dream when combined with the 2R interior finish. Heavy-duty sealing mechanism and gasket form a seal on top with a stainless steel lid equipped with a T.C. port for adding accessories or an airlock. The inside is finished to Speidel quality standards with flawless welds and a 2R finish.
The tanks will support a few PSI of pressure, however, they are not pressure-rated or designed to be used under pressure.
Tank Ports
Tanks feature 1.5" T.C. outlets (1 on bottom for complete drainage, one in middle for racking arm, one on top for blowoff/airlock), and also two welded DIN fittings. One DIN port is equipped with an included sample valve and the other has an included thermometer and thermowell combination. The cooling jackets have two 1” NPT ports.
Speidel Quality Features
Full Jacket - These tanks are equipped with a max cooling jacket rated to 6-bar. This will allow you to hook it into a glycol system for complete temperature control.
Interior Finish - Speidel tanks feature an ultra-smooth 2R interior surface which allows you to clean your tanks with cold water, without scrubbing. This saves significant labor costs.
Weld Quality - Speidel's robotic-arm laser welders create flawless stainless-to-stainless junctions that look and feel more like a taped fabric seam than a traditional weld. Ultra high-quality welds leave no chance for residual products to harbor spoilage organisms.
Warranty - Speidel and MoreWine! Pro back up each and every tank with an industry-leading 25-year warranty against defects in materials or workmanship.
Thickness - Speidel tanks are on average around 25% thicker than Italian-manufactured tanks of the same general capacity and dimensions.
Complete Drainage Bottoms - These tanks are outfitted with vaulted bottoms for total drainage, which maximizes product yield at racking and makes cleaning a snap.
Tank Features:
Full Volume of 625 L (165 gal)
1.5" T.C. Drain, Racking Port, and Lid outlet
8.5" Top hatch for easy cleaning and additions
2 X DIN10 Fittings w/ Sample Valve and Thermowell/Thermometer combo
Tank Dimensions: 820mm D x 1661mm H (32.25" D x 60" H)
S-04 produces fruity and floral notes and is ideal for a large range of American and English Ales
A fast fermenting, highly flocculent strain that tends to produce beers with higher clarity
Fermentis active dry yeast offers reliability, ease-of-use, and consistency to home and professional beverage makers across the world
Homebrewers love this commercial English Ale yeast for its big, clean flavor; its rapid fermentation; and its highly flocculant character.
Widely recommended for practically any American or English style beer, S-04 yeast a rapid starter and finisher which settles out extremely well, leading to a clean finished beer. Great to keep a few packets as back-ups or just to use as a less-expensive alternative to liquid cultures.
This yeast can be pitched directly, but if you prefer to rehydrate, the instructions are below.
Sprinkle the yeast in a minimum of 10 times its weight of sterile water or wort (we suggest 4 oz) at 70°F to 77°F (21 to 25 °C). Do not stir. Leave to rest 15 to 30 minutes. Gently stir for 30 minutes, and pitch the resultant cream into the fermentation vessel.
Attenuation: 74-82%
Sedimentation Time: Fast
Alcohol Tolerance: 9-11% ABV
Optimum Fermentation Temp: 64-78°F
*See the technical data sheet below for more information on rehydration, usage and storage.
The German made 1.2 horse power MB Chiller is an ideal solution for nano breweries looking to chill up to 10 fermenters at once. The idea of the MiniChilly is that for each fermenter you want to a chill a pump kit is added. A pump kit (GLY35) includes a submersible pump that is placed in the cold bath of the Mini Chilly along with a digital controller that is placed next to your fermenter. Silicone tubing is included to make the connections. The digital controller includes a thermal probe that should be inserted into a thermal well in your vessel or can be taped to the outside of the vessel if you don't have a thermal well. The digital controller then measures the temperature of your tank and turns the submersible pump on or off to cool the liquid in your vessel to the desired set temperature. In this way each tank can be set at different temperatures. The MiniChilly is made by Quantor/Kreyer of Germany who is the largest manufacturer of glycol systems for breweries and wineries in the world. Made with high quality manufacturing and components, the MiniChilly is a durable system for many years of problem-free brewing. It is German made and we guarantee you will appreciate the build quality when compared to other chillers on the market. The unit features a stainless steel case with stainless 3/8" barbs in the top that allow for a clean connection of the silicone tubing that will run from each pump to each tank. The MiniChilly is able to chill its reservoir down to 21°F when a 30% glycol solution is used. The compact size and included casters make it easy to move around the brewery when needed. Applications: Cooling of Fermentation Cold Crashing for Brite Tanks Maintain Lagering Temperatures Compatibility: The MiniChilly can be used with any fermenter that has a built-in cooling jacket or a submersed cooling coil. It works well as the cooling source for the following systems and fermenters. BrewBuilt Jacketed Uni Conical - You will need one Glycol Pump Kit for each tank. Ss Brewtech Fermenters and Brites with optional FTS Temperature Control Systems: Because FTS systems include a pump and controller you will not need to buy a separate Glycol Pump Kit. Spike Conical with Optional Cooling Package - Because the optional Spike cooling system includes a pump and controller you will not need to buy a separate Glycol Pump Kit. Speidel Tanks with Optional Cooling Jackets - You will need one Glycol Pump Kit for each tank. Grainfather Fermenters - Grainfather fermenters have standard cooling jackets. You will need one Glycol Pump Kit for each fermenter Blichmann Fermenators with Optional Cooling Coil - You will need one Glycol Pump Kit for each Fermenator. Capacity: Many chiller ratings are based on the theoretical power of the compressor, while the cooling capacity of the MiniChilly is rated at a realistic ambient temperature. This is much more useful for predicting the MiniChilly’s performance in real world applications. Of course, you could cool a greater number of smaller tanks but you’re ultimately limited to the 10 connections. Actual cooling capacities will vary based on the insulation of the tank. For the examples below we assume neoprene or better. Cooling Capacity Example: Up to 10 1BBL (31 Gallon) well-insulated tanks fermenting at 68°F in 80°F ambient temperature. For every fermenter you want to cold crash remove 4 fermenting fermenters from the capacity. Set Up: In order to hook up the MiniChilly to your fermenter or tank's cooling system, you will need 4 lengths of tubing per pump. All tubing connections should be secured with hose clamps. Length 1: Submersible pump outlet to inner barb of 1st bulkhead Length 2: Outer barb of 1st bulkhead to cooling system inlet Length 3: Cooling system outlet to outer barb of 2nd bulkhead Length 4: Inner barb of 2nd bulkhead to MiniChilly reservoir (should drain freely, no connection necessary) Technical Characteristics:
Power: 110V-1Ph/50-60Hz Compressor Power: 1.2hp/900watts Cooling Capacity at 32°F glycol temp and 90°F Ambient Temp: 1.05 KW/1050 Watts (60Hz 110V) Cooling Capacity at 60°F glycol temp and 90°F Ambient Temp: 1.92 KW/1920 Watts (60Hz 110V) Stainless Steel Unit Water Temperature Range: 21°F - 86°F (-6°C - 30°C) Ambient Temperature Range: 50°F - 90°F (10°C - 32°C) Refrigerant R134a Free Glycol Water-Bath for Mini-Pumps Fittings 3/8" for Plastic Tubes of Individual Pumps Solid Wheels w/ Breaks for Easy Mobility Universal C19 Plug On/Off Switch Water-Level Sight-Tube Grooves for Individual Pump Cables Safety Inner Separation Water Side from Electric Side Tank Capacity: 12.68 gal. (48 L) Dimensions: 29.5"L x 15.75"W x 21.75"H Weight: 112.5 lbs Made in Germany CE Certified
Stainless steel tri-clamp reducing elbow. Specifically manufactured as an alternative for the FermZilla 27L and 55L Tri-Conical bottom dump port. If you would like to bypass the 3" x 2" butterfly valve and collection container on your FermZilla Tri-Conical, you can use this reducing elbow to go directly to a 1.5" tri-clamp valve.
KegLand Part Number: KL29469
This is a 304 stainless steel blow off tube for Ss Brewtech 14 gallon Chronical fermenters. Fits perfectly on the 3" TC dome lids and comes with a built-in relief valve. The two-piece cane has an outer diameter of 15 mm (approx. 9/16") and 3/8" NPT where they connect. 3" TC gasket and clamp not included.
This stainless steel hop tube is ideal for keeping kettle additions from clogging your pump or heat exchanger, and works perfectly for dry hopping in a keg or wide-mouth fermenter. Holds approximately 5 oz of pellet hops, allowing some space to permit full extraction of the hop oils. The stainless chain makes it the perfect partner to our Corny Keg Lid with Welded Tab. Hang the tube inside your keg for post fermentation hop, fruit, wood chip, or spice additions. When it's time to remove the hops/adjuncts simply pull the tube out. Works great for timing exactly how long your beer sits on the hops, oak, or other flavoring addition. 2.6" diameter 11.8" tall Made from 304 stainless steel Kegland Part Number: KL05210
Variable capacity tank well-suited for fermentation, wine aging, kombucha, and other applications Floating lid can be positioned as needed to match the volume of the liquid you're working with Proprietary rubber lid gasket allows for a superior seal compared to traditional gaskets, providing better protection for your wine Cooling jacket covers the entire tank of efficient glycol cooling Pulley rope for lowering and lifting the floating lid Swinging manway door for easy removal of grape skins Made in Germany by Speidel We are proud to present our line of premium quality stainless steel tanks. Built in Germany by Speidel, the world-class traditions of German engineering and craftsmanship are reflected in these tanks. And, after examining tanks built by every major manufacturer worldwide, we can safely say that when it comes to features, quality and price, these tanks represent the very best value available in stainless steel wine storage. Speidel Quality Features: Cooling Jacket - This tank is equipped with a max coverage jacket that covers all accessible areas of the tank and is designed for an operating pressure of 2.5 to 6 bar. This will allow you to hook it into a glycol system (see our Kreyer Chilly45, GLY410) for complete temperature control! Interior Finish - Speidel tanks feature an ultra-smooth 2R rated interior surface which effectively resists the build-up of tartrate residues. Clean your tanks with cold water after cold stabilization! Say goodbye to harsh cleaning chemicals and expensive CIP systems! Weld Quality - Speidel's robotic-arm laser welders create flawless stainless to stainless junctions that look and feel more like a taped fabric seam than a traditional weld. Ultra high-quality welds leave no chance for residual product to harbor spoilage organisms. Thickness - Speidel tanks are designed to be the correct thickness for the tank's total volume. Manway - The "red wine" manway allows you to easily remove skins. Complete Drainage Bottoms - All Speidel tanks are outfitted with conical, pocketed bottoms for total drainage, which maximizes product yield at rackings and makes cleaning a snap. *Please note that smaller, flat-bottomed tanks do not feature total drainage bottoms. Tri-Clamp Valve Ferrules - All Speidel tanks come configured for use with Tri-Clamp (TC) style valves and fittings. Tanks up to 1600L capacity are outfitted for use with 1.5in TC. Other sizes and custom configurations are available at additional cost upon request. **Please Note: TC valves not included. Please inquire with your sales associate for pricing on TC valves and fittings. Rubber Lid Gaskets - The white rubber gaskets used by Speidel are much thicker than the traditional clear vinyl gaskets, which along with their extruded manufacturing process provide a much better seal with the tanks wall. They're seamless and more oxygen resistant than the clear gaskets. That means better protection for your wines! Warranty - Speidel-Behaelter, GMBH backs up each and every tank with an industry-leading 25 year warranty against defects in materials or workmanship. And, as a 5th generation manufacturer, you can be confident they'll be around to honor that warranty should the need arise. Tank Features: Volume: Sealed, 1100 L. Open top, 1183 L Variable Capacity Tank includes Floating lid and Heavy Duty White Rubber Gasket Manway Max Coverage Jacket: 2.0 m² (4x 1" MPT connections) Complete Drainage Dish Bottom Sight Gauge Lifting Arm Extended Legs - bottom dump port located 16.8" off the ground Reinforced Racking valve 1.5" TC connections Thermometer and Thermowell Combo included Sample Valve included Tank Dimensions: 1080mm D x 2010mm H (42.5" D x 79.1" H) With Lifting Arm: 2435mm H (95.8" H) Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.
A Pressure Relief Valve upgrade or replacement for the Chronical line of fermenters from Ss BrewTech.
Features:
Standard replacement part for Half Barrel
Can be retrofitted to 7 Gal Chronical lid
Releases pressure between 2-2.5 psi
Food grade silicone O-ring
Use Dewalt DWA1783IR step bit for retrofit
For 7/32" inch hole diameter (in lid)
F-2 was specifically selected for secondary fermentation in bottle and in cask
Neutral aroma profile and high alcohol resistance make it perfect for refermentation bottle conditioning
Sticks well at the bottom of the bottles/casks
Fermentis active dry yeast offers reliability, ease-of-use, and consistency to home and professional beverage makers across the world
SafAle™ F-2 is specifically selected for secondary fermentation in bottle and in cask. This yeast assimilates very little maltotriose but assimilates basic sugars (glucose, fructose, saccharose, maltose) and is characterized by a neutral aroma profile respecting the base beer character. Its neutral aroma profile, high alcohol resistance and stickiness characteristics make it a perfect match for consistent re-fermentation in bottle and cask.
SafAle™ F-2 resists to high alcohol levels (>10% v/v) and allows brewers to obtain all the properties of refermentation such as:
Beer preservation thanks to oxygen trapping
Contribution in roundness and maturation aromas
Carbonation
Sticks well at the bottom of the bottles/casks and forms a nice haze when it is resuspended
Usage:
Add 19 to 38 grams of sugar per gallon of beer (5 to 10 grams of sugar per liter) to obtain a saturation of 2.5 to 5.0 g/l of CO2
Pitch the sweetened beer, that should be at fermentation temperature (68-77°F / 20-25°C) with the rehydrated yeast. Carbonation will be achieved in 1 to 2 weeks at 68-77°F. Carbonation at 59°F can take over 2 weeks
At the end of refermentation, the beer can be cooled down and will gain in roundness after 2 to 3 weeks
Please note: Example image shows a 20g sachet. The correct size is 25g. Updated image coming soon.
Unitank Light offers the same tank body as the standard Brewtools Unitank with a slight difference in included accessories for a more affordable price
Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank
Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils
Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use
Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup
Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe
All valves, fittings, and gaskets come included
Unitank Light is the same tank body as the standard Brewtools Unitank, but with slightly less equipment and some parts made from Polyketone (POK), which vastly reduces cost without compromising the user experience for smaller tanks. Unitank Light can be upgraded to a standard Unitank where you prefer.
Key Differences:
CleanCore butterfly valves made from Polyketone
Barbed blow-off PRV
Can be set to open during fermentation for blow-off
Also acts as 2 bar / 30 psi safety valve
Pushfit sample valve
Compatible with optional Push-fit Coil and Adapter
Polyketone 8” to 3” tri-clamp lid adapter replaces stainless steel adapter
Polyketone racking arm replaces stainless steel racking arm
Does not include neoprene insulation jacket, ss blow-off tube or ss blow-off valve
Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high-end fermentation tanks with new features and a lot of possibilities.
Key Features:
Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation
Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a coil
Many options for connecting accessories like sensors, heaters, carb. stones and other accessories
Conical pressure rated for 2 bar / 30 PSI
Cooling jacket pressure rated for 0.5 bar / 7 PSI
8" TC port on top for easy access
2" TC dump and racking valves
Brewtools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party.
Specifications:
Low height w/o acc.: 32.6"
Max height w/o acc.: 40.5"
Packaging size: 33.4" (h) x 20.5" (w) x 20.5" (d)
Net weight: 73 lbs
Gross weight: 88 lbs
Tank diameter (inside): Ø15.75"
Gross volume: 13.5 gal
Max rec. volume: 10.5 gal
Min rec. volume: 5.3 gal
Volume, cone: 3.1 gal
Material: 1.5mm stainless steel (SS304)
Operating pressure: 1.0 bar / 15 PSI
Max pressure: 2.0 bar / 30 PSI
Min. pH: 4.0
In the box:
Unitank with adjustable frame
1 pcs Analog pressure gauge, TC34mm
2 pcs CleanCore Butterfly-valve, 2"
1 pcs Racking arm 2", POK
1 pcs TC elbow 90°, 2"
1 pcs Sample valve, 34mm, POK
1 pcs TC Adapter 8"-3", POK
1 pcs TC blind cap, 3"
1 pcs TC blind cap 2"
2 pcs TC blind cap 1.5"
4 pcs TC blind cap 34mm
2 pcs TC gasket 8" lipped
2 pcs TC gasket 3"
2 pcs TC gasket 2" 5-pack
1 pcs TC gasket 1.5" 5-pack
3 pcs TC gasket 34mm 5-pack (DN20)
1 pcs Tri Clamp 8"
1 pcs Tri Clamp 3"
5 pcs Tri Clamp 2"
2 pcs Tri Clamp 1.5"
9 pcs Tri Clamp 34mm
1 pcs TC tool
4 pcs M10 steel/rubber feet
1 pcs TC34mm pull-type PRV/Safety valve with 7mm barb
1.5m (4.9') Silicone tube 6x10mm
Necessary bolts and parts for assembly
5 year manufacturer's warranty
Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Carb. stone kit with Ball-Lock, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, 2" sight glass etc.
For User Manuals and support, please follow this link to Brewtools Docs.
NOTE: Model in photo is a prototype. Minor changes and improvements may occur.
Want an easy-to-use, stainless vessel that ferments and carbonates? This 50L/13.2 Gallon keg has been modified to allow you to do both! The top is fitted with a large 4 inch tri-clamp lid with two ball lock posts and a pressure relief valve. You can use this vessel to ferment, carbonate, serve, or push the beer through a filter. The posts are recessed which allows you to stack these kegs up to 4 high. A 4" T.C. end cap with pre drilled hole is also available (H691), which can be paired with a #3 stopper and airlock. Also consider the Kegmenter Hop Bong Pressure Pack which allows for oxygen-free dry hopping and also features ball lock posts for Gas & Liquid. Depending on how long it will take to consume the finished beer, we recommend using two kegmenters, one for fermentation and one for carbonating and serving. After fermentation, there will be a large trub cake at the bottom of the vessel. Leaving finished beer on the trub for too long (2-3 weeks) may eventually lead to off-flavors. Check out our ball lock jumper line (KEG575) to easily transfer from one kegmenter to the other. Also consider our beer filter kit (FIL40), which will allow you to filter the beer during transfer. Features: Rated up to 2.5 BAR (36 psi) 4" T.C. lid with ball lock posts Floating dip tube Stainless steel 1.8 mm thick Use: As a stainless steel fermenter that is easy to clean Great choice for 10 gallon fermentations Easy to pressurize the kegmenter after fermentation to push through a filter and into another keg Fermenting under pressure, allowing CO2 to exit via the relief valve, reduces esters and fusel alcohol production allowing you to ferment at warmer temperatures Distillation - with the addition of a T.C. reducer and condenser (H701 / DS120 / DS130) As a cellar keg for topping up barrels Warning: Always depressurize keg before removing lid. Does not come with spunding valve show in example photo. See FIL42A. Kegland Part number: KL04565
Compatible with the 27L and 55L FermZilla Tri-Conical Series or any 2" T.C. fittings. Primarily designed to be used with the FermZilla T.C. Pressure Lid and 2" Hop Bong for oxygen-free dry hopping.
If you're planning on putting your FermZilla Tri-Conical or All Rounder in a Fermentation Chamber, you will want to allow for 420 mm (16.5") of clearance measured from the base of the ring collar to a comfortable level below the chamber ceiling so you can pull the PRV to purge oxygen from the hop bong.
KegLand Part Number: KL27564
The Deluxe Yeast Starter Kit will have you making top shelf yeast starters right out of the box. Yeast starters offer higher cell counts at the time the yeast is pitched, leading to faster, healthier fermentations and better tasting beer! Any beer will benefit from a yeast starter, but they're especially recommended for high gravity beers and cold fermenting lagers.
This kit includes step-by-step instructions for making a 2L starter, as well as some fantastic upgrades that set it apart from our standard Y320 starter kit. Once you've prepared the starter, sanitize and drop in the stir bar, install the foam stopper, and place the flask on the magnetic stir plate. Turn the dial up until a shallow vortex forms.
Magnetic Stir Plate
A stir plate will greatly improve the quality of your yeast starter by providing continuous aeration. Yeast need oxygen to produce sterols and multiply. When all the available oxygen is used up the yeast will stop reproducing. Using a stir plate will ensure that your yeast have all the oxygen they could ever want and they'll be able to reproduce as much as possible.
Foam Stopper
Many yeast starter kits include a rubber stopper and airlock, but we believe a foam stopper is the clear choice. The foam stopper will allow air to flow freely into your flask while keeping pesky bugs and other contaminants out. Simply spray or dunk the stopper in sanitizer before installing it. If you're going to store the starter for a couple days after its finished, remove the foam stopper and cover the flask with sanitized aluminum foil.
Foam Axe
Foam Axe from CellarScience® is a uniquely formulated anti-foaming agent which reduces surface tension so bubbles are Axed before they can form. Foam Axe can be used in the kettle to help prevent boil-overs and works great in your fermenter or starter flask to reduce Krausen—stopping your viable yeast from fermenting out the top of your vessel. Just one drop in your flask is all you need.
Flask Marker
This wax pencil is used for writing on glass surfaces and washes off easily. Great for labeling and writing notes on your yeast starter.
Kit Includes:
2000 mL Erlenmeyer flask (student grade)
Magnetic Stir Plate (stir bar included)
Foam Stopper
1/2 lb Dried Malt Extract
1 oz Fermaid K yeast nutrient
1 oz Foam Axe foam control
Flask Marker wax pencil
In the lab world, these flasks are known as "Student Grade". A great flask for making yeast starters! (Student grade is not the highest grade flasks and will have minor defects)