Translucent, food-grade tubing temperature rated to 500F.
Odorless, tasteless, and inert Silicone tubing is FDA food-grade approved from -100F to 500F. Translucent natural color allows you to see the flow. The perfect tubing for building a personal brewery, especially for any time that the wort in contact with tubing will be above 180F. This tubing is not designed to hold pressures above 20psi. It works great with our magnetic drive pumps such as a March or Chugger pump, but we do not recommend it with a impeller pump or for use with household water pressure.
Platinum Cured
Quantity ordered will be shipped as multiple pre-cut lengths. Maximum length available is 100 ft.
*Will burst at 30 PSI at 70F.
This is the replacement gasket that seals the lid onto the body of the plastic Speidel fermenters. This gasket generally does not wear down through normal use and need to be replaced. That being said, everyone seems to manage to find creative ways to use our equipment that results in needing replacement parts!
This gasket fits our 60l(15.9 gal) & 120L (31.7 gal) Speidel Round Plastic Fermenters.
Anvil Brewing Equipment ball valve is made from 304 stainless steel. This robust custom designed kettle drain valve has an integral bulkhead seal that forms an extremely rigid and leak-free joint. The convenient ½” NPT male fitting inside of the kettle allows mounting of nearly any accessory. Simple to install in any 7/8” hole and will never leak like other weldless connections! Easy to disassemble and clean. Add our dip tube for a complete draining system!
When installed, the valve O-Ring will sit in the groove on the back of the valve, on the outside of the kettle.
Replacement O-Ring for the OLDER (before 2005) ball valve, sight gauge, and thermometer. 1/2" ID with a 1/8" cross section. This is made of ethylene Propylene. This will withstand temperatures to 400 degrees and ultra violet light.
The Alembic Copper Domed lid will help you achieve a smoother, richer, sweeter tasting spirit by helping to remove unwanted sulfur compounds. The large copper surface area acts as a catalyst with distilling vapor to enhance and concentrate flavors and aromas during the distilling process. Primarily intended for use with the Copper Pot Still, but it can also be used with the Copper Reflux still if desired. Note: This lid uses a 6mm gasket to better fit the Gen 4 BrewZilla and Gen 2 DigiBoil. It is also backwards compatible with Gen 3 and older BrewZillas and Gen 1 DigiBoils. To improve the seal further, we highly recommend using the Adjustable Lid Clamps with the Distillation Lid if your unit does not have them. 9-1/2" Tall 12-3/8" Diameter. Please note that copper is a very soft metal and can be dented quite easily. Store and use with care. KegLand Part number: KL1589 Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States. It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA).
High performance primary regulator designed to handle the workload of dispensing from multiple taps without freezing up!
Dual high-pressure and low-pressure gauges to easily reference CO2 cylinder pressure and output pressure
Pressure settings are easily adjusted by hand using the large plastic adjustment knob
CGA320 inlet features a built-in gasket where the unit attaches to the CO2 tank—eliminating the need of replacing fiber washers with each tank swap
Made in the USA. Taprite is one of leading manufacturers of gas regulators and draft dispensing equipment
One-way shutoff valve outlet protects your regulator from backflow and can be turned on/off to stop gas flow without needing to close your tank
When it comes to CO2 regulators, we’ve tried them all. This quality unit by Taprite is our favorite on the market. It’s no wonder this regulator is trusted by so many breweries and beer bars—it represents the best quality at a great price. Available in a standard, single-body model, as well as a dual-body model which allows you to send different pressures to two separate kegs from the same CO2 tank!
The things you’ll love about this regulator are:
The large front knob makes pressure adjustment tool-free, easy & fast.
The built-in gasket where the regulator connects to the CO2 tank eliminates the constant replacement of fiber washers every time you change out your tank.
The barbed outlet features a one-way on/off valve which prevents backflow and protects the regulator’s internals.
The gauges are easy to read. The low pressure gauge reads from 0 to 60 psi. The optional available gauge cage is the best on the market.
This is the T742HP model, where the HP stands for high performance; it won't freeze up when multiple taps are running at once.
Best of all is the consistent pressure regulation. With many regulators the pressure can 'creep' up over time. This unit holds the pressure rock steady. No drifting.
Built by Taprite, an American company.
Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets.
For 2" tri-clamp fittings.
KegLand Part Number: KL03438
Savvy homebrewers love quick disconnects on their gas lines! They give you the ability to quickly move hoses from one configuration to another with ease! These quick disconnects feature 3/8" barbed fittings which can be used with 5/16", 3/8" or 7/16" line. The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you don’t need to worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade Buna-N. In short, these QDs are durable, user friendly and versatile. A no-brainer! This is a direct replacement to the Female Quick Disconnect with 3/8" Barbs that is featured on the BrewBuilt CoolStix™.
Use these high quality, food-grade quick-disconnects on your gas and beer tubing lines. Uses might include the following:
* On a gas system to unhook your tank and regulator from your manifold so you take it with you.
* On a beer line to easily switch between ball lock, pin-lock, or a commercial tap
* On a counter-pressure bottle filler to be able to easily connect to your existing gas line.
This plastic quick disconnect set features 1/4" barb which can be used with tubing ID 3/16" through 5/16". The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you need not worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade buna-n.
Solenoid valve made from stainless steel. Designed for glycol, water and air/co2. T.C. 34mm ports in both ends for maximum flexibility. Coil and plunger Italian-made by ACL. The valve can easily ble disassembled and cleaned.
Coil has DIN 43650 Type A connector (not included).
Normally used with T.C. 34mm to 3/8" NPT threaded adapter and leak-free quick connectors on one or both sides depending on setup.
Specifications:
Ports: TC34mm / TC34mm
Operation: NC (normally closed)
Power supply: DC24V, 10W
Orifice: Ø4.5mm
Pressure rating: Max 3 bar / 43 PSI
Prevents leaks and spills when disconnected, ideal for pressurized systems
Handles both hot and sub-zero fluids, from hot transfers to sub-zero glycol mixtures (-40°F to 280°F)
Made with high-strength, chemically resistant polyketone plastic body, 316 stainless steel spring, and EPDM O-ring for long-lasting performance
JoinTech Connectors offer a premium quick-disconnect solution for high and low-temperature beverage handling. These fittings are suitable for a wide range of applications, from hot transfers to sub-zero glycol mixtures.
The connectors feature an automatic shut-off valve that prevents flow when disconnected, making them ideal for hoses used with pumps or glycol systems.
Features:
Durable, UV-stable black design
Automatic shut-off valve
Vacuum rating of 60 psi
Connections:
JoinTech Male QD
1/2" Barb
Materials:
Body: High-strength, chemically resistant polyketone plastic
Spring: 316 stainless steel
O-ring: EPDM
Specifications:
Operating pressure: Vacuum to 60 psi
Temperature tolerance: -40°F to 280°F (-40°C to 138°C)
Flow path: 3/8"
KegLand Part Number: KL50746
This tubing is so much better than the standard tubing most brewers start with. Silicone Tubing is odorless, tasteless, and is NSF approvedd as food-grade at temperatures from -100F to 500F. The translucent color allows you to see your wort flowing. It withstands high heat, which is great for any time that the wort in contact with tubing will be above 180F, which is the temperature threshold for most vinyl tubing. It doesn’t slip off of your equipment, never kinks, and easily slides on and off of barbed fittings without deforming or leaking. It is so easy to work with that once you’ve tried it on one piece of your equipment, you’ll want to upgrade your whole setup!
1/4" ID
7/16" OD
Platinum Cured
Not designed to hold pressures above 20 psi. Will burst at 30 psi at 70F.
Designed specifically for mounting the NukaTap Mini Beer Faucet on any kegerator, keezer, cold room wall, or other flat surface Connect beer line directly to the faucet, reducing the amount of temperature loss to a standard draft shank No spinning faucets. Your tap will remain in a fixed orientation once locked into the collet Easy installation. No need to drill a large hole through your fridge to accommodate a standard 5/8" draft shank Use with 6.35 mm OD EVABarrier draft tubing This shank kit is specifically designed to suit the NukaTap Mini Beer Faucet and will allow you to connect the NukaTap Mini to a cooler box, kegerator, keg fridge, cold room wall or any other flat surface. This wall mount shank kit is for use with 6.35 mm OD EVABarrier. For the shank kit for use with 8 mm OD EVABarrier, see here. New Innovative Shank Design Unlike other shank kits, this kit doesn't use a bulky 5/8" threaded shank. The issue with a standard draft shank is that acts as a heat sink, and due to the fact that most shanks sit inside an insulated wall, this results in a substantial amount of warm beer coming out of the tap before cold beer starts flowing. This results in substantial "first pour foam" effect which wastes beer, can result in sour beer, and ultimately negatively effects the quality of the beverages being served. This new design has the beer line feed all the way directly up to the back of the faucet, greatly reducing the volume of non-refrigerated beer. No Spinning Shanks If you have ever installed a traditional 5/8" long shank, you will know how frustrating it is when you use the faucet and it starts rotating. This new design of shank alternative uses three screws that lock the tap into a fixed position and prevents the taps from rotating. If you loosen the 1/2" stainless tap collet you can still have the flexibility to rotate the faucet to any orientation, but once the collet is tight, interlocking teeth on this shank kit and the NukaTap Mini will hold the tap permanently in the correct orientation. Easy Installation Another advantage compared to standard shanks is that this kit doesn't require you to drill a large 3/4"-1" hole through the wall. As no shank is required, only a hole large enough to accommodate the beer line is required. As a result, an 8mm (5/16") conventional drill bit is all that is necessary for installation. However, if you are concerned about the small amount of beer sitting in the draft line inside the wall not being refrigerated, you can also shell out a larger diameter of foam on the inside of the wall to allow cold air to circulate around the beer line thus reducing the non-refrigerated beer in the line even more. If you wanted to do this the Step Drill Bit is the best tool for the job. Any Wall Thickness Other shank kits will require you to purchase a specific length shank for a specific wall thickness. This new shank alternative will fit any wall thickness. If you have wall thicknesses that are less than 2.7" thick then you can use the included screws that have "snap off" points so you can simply cut the screws down to the desired length. However, if the wall is thicker than 2.7" you can simply purchase a conventional screw from the hardware store and screw the shank kit to your wall. If the substrate is firm enough you may not even need to go all the way through the wall so a common 1-1/4" long screw may be all that is required. Specifications: Beer Line Diameter: 6.35 mm OD EVABarrier Collet and Screw Cover: 304 Grade Stainless Steel O-ring Material: Dual O-ring Silicone/EPDM combination Plastic Mounting: Polyketone (POK) Temperature Range: 14-212°F (-10-100°C) Max Pressure: 150 psi KegLand Part Number: KL32193
This BrewBuilt Stainless Steel Ball Valve features a locking mechanism that keeps the valve from being opened by a child or passing dog while you are brewing. Easy to clean 2 piece design, constructed from high grade 304-stainless made to last. 1/2" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and the two PTFE gaskets that form the seal when closed.
Features:
1/2" FPT on inlet and outlet
Locking Mechanism on Handle
304 SS construction with PTFE gaskets
Two-Piece Construction for easy cleaning
Full Port design for minimal pressure loss / resistance
BrewBuilt: Designed for Brewing, Built to Last.
Chill your beer in the summer and warm your beer in the winter! Use a chill water source when it's hot or warmed water if it's cold! Temperature control during fermentation is one of the most significant contributors to the flavor of our beers, yet it all too often gets overlooked. This particular unit is designed to work specifically with the Brew Bucket Mini.
Brewers typically have limited the styles of beers they produce to the varying temperatures of the seasons. The system is elegant and engineered, yet it stays true to the heart and soul of us home brewers. The FTSs uses a precision digital temperature controller in combination with a 304 stainless steel immersion chiller. The digital controller constantly monitors your beer’s temperature and will activate the circulation pump (which, by the way, is quieter than a mouse) to hold the fermentation temperature at your predetermined set point. You can crash cool or lager too! You supply the chill water source, which can be as simple as ice water in a cooler or as involved as glycol from a chiller’s reservoir. We supply the rest of the system. As long time fellow home brewers, this is a system we know many of you have been dreaming about for a long time: advanced temperature control for the beers you make at an affordable price.
Features:
Custom lid w/ 304 Ss immersion chiller coil
Pro grade (super quiet) submersible pump
110-240V power supply
304 Ss weldless lid mounted thermowell
Tailored neoprene insulation jacket
Digital temperature controller
Comes with a back nut, plastic collar, hex nut, and 8 mm Duotight Adapter compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Requires a 1" hole saw for installation. When set in place, the shank will only have about 2 1/2" of length to pass through your wall or fridge door, due to the length of the collar and back nut. Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 5-1/8" - Total Length (Tip to Tip) 4" - Shank Length (Without Nut & Barb) 3" - Thread Length 2-1/2" - Pass Through Length Kegland Part number: KL11945
Solenoid valve made from stainless steel. Designed for glycol, water and air/co2.
TC3mm ports in both ends for maximum flexibility.
Coil and plunger Italian-made by ACL.
The valve can easily ble disassembled and cleaned.
Coil has DIN 43650 Type A connector (not included).
Specifications:
Ports: TC 1.5" / TC 1.5"
Operation: NC (normally closed)
Power supply: DC24V, 10W
Orifice: Ø4.5mm
Pressure rating: Max 3 bar / 43 PSI
In the rare event that a small part of your equipment get lost or broken, the last thing you want to do is replace the entire thing! Thank goodness for replacement parts!
This is the replacement gasket that seals the lid onto the body of the plastic Speidel fermenters.
While these gaskets usually don’t wear out through normal use, it’s nice to be able to get a replacement if you need it!
This gasket fits our 12L (3.2 gal) Speidel Plastic Fermenter.
Prevents leaks and spills when disconnected, ideal for pressurized systems
Handles both hot and sub-zero fluids, from hot transfers to sub-zero glycol mixtures (-40°F to 280°F)
Made with high-strength, chemically resistant polyketone plastic body, 316 stainless steel spring, and EPDM O-ring for long-lasting performance
JoinTech Connectors offer a premium quick-disconnect solution for high and low-temperature beverage handling. These fittings are suitable for a wide range of applications, from hot transfers to sub-zero glycol mixtures.
The connectors feature an automatic shut-off valve that prevents flow when disconnected, making them ideal for hoses used with pumps or glycol systems.
Features:
Durable, UV-stable black design
Automatic shut-off valve
Vacuum rating of 60 psi
Connections:
JoinTech Female QD
1/2" Male BSPT
Materials:
Body: High-strength, chemically resistant polyketone plastic
Spring: 316 stainless steel
O-ring: EPDM
Specifications:
Operating pressure: Vacuum to 60 psi
Temperature tolerance: -40°F to 280°F (-40°C to 138°C)
Flow path: 3/8"
KegLand Part Number: KL50739
Replacement gaskets and o-rings for standard US keg couplers (D-Style) and European keg couplers (S-Style). Other than the probe washer, they use the same gaskets and check valves.
Brewtools pro steam hats are designed for maximum flexibility. They feature a silicone edge seal, 4 clamps to hold it in place on your brewing system, a 110mm inspection hole you can add your hops through when boiling, 2 silicone covered handles and a 4 inch accessory mount on top. The silicone plug for the inspection hole is included. Remember to order clamp and gasket for the top port. For User Manuals and support, please follow this link to Brewtools Docs.
EPDM gaskets have a more narrow temperature range than silicone gaskets, but they are more resistant to acids and caustic chemicals.
For 2.5" tri-clamp fittings
Made from Silicone
Temperature rated from -30°F to 300°F
ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.
Replacement lid gasket for 60L - 500L Speidel Rectangular Plastic Storage tank lids. Please note these replacement gaskets are for the newer generation tanks introduced in 2017. A redesign of the lid called for a different sized gasket. The new generation gaskets are 7-3/4" in diameter and 3/8" thick. The older generation gaskets are 7" in diameter, and 1/4" thick. For the Pre 2017 lid gasket please see FE736.
This tailpiece is a replacement for the gas-in barb that comes mounted on our D1505 Sanke Tap. It will not work as a 5/16" beer line connection due to the lip on the back side of the fitting.
Tailpieces are fittings which connect beer and gas tubing to the different parts of a draft system. One side of the tailpiece features a barb to connect the tubing to, and the other side is held against the tap or faucet shank with collar nut.
Tailpieces are available in a range of barb sizes to fit up to your tubing size.
Kit for dryhopping and adding other ingredients to a pressurized fermenter without oxygen. This is the correct size for the Brewtools F40 and F80 Unitanks.
Included in the box:
Butterfly-valve, TC 3"
TC Adapter, 3" to 34mm
TC Pipe, 3", L=200mm
Tri Clamp, 3" (2 pcs)
Tri Clamp, 34mm (3 pcs)
TC34mm Manual PRV
TC34mm Ball Lock connector, Gas
TC Tee, 34mm, L=60mm
TC Gasket, 3", (3 pcs)
TC Gasket, 34mm DN20, 5-pack
