This Reactor Rod was custom built to be used with the 2 bbl MB Conical Fermenter, but can easily be integrated to other vessels with a 4" tri-clamp top port. Unlike other in-solution cooling coils on the market, the Reactor Rod utilizes a straight vertical design. Without all the curves and bends of a cooling coil, it is easier to scrub and sanitize the unit prior to setup and after use. The four cooling rods are 41" long measured from the bottom of the T.C. fitting.
Perhaps your wort was too hot when you transferred from the kettle, or while cleaning you dropped the FermZilla against something sharp that punched a hole, or maybe it's just time to replace the tank after acquiring too many scratches from normal wear-and-tear. Whatever the reason, no need to go buy a whole new FermZilla! Just pick up one of these fresh replacement tanks and your conical fermenter will be good as new! Pressure Stress If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple: Fill the tank to the brim with water Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher Pressurize the tank to 4 BAR (58 psi) Check for leaks, then replace the Red PRV when finished If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla. General Care Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank. KegLand Part Number: KL15219 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.
Replacement PET Tank for the 55L Tri-Conical FermZilla with tri-clamp bottom port. Perhaps your wort was too hot when you transferred from the kettle, or while cleaning you dropped the FermZilla against something sharp that punched a hole, or maybe it's just time to replace the tank after acquiring too many scratches from normal wear-and-tear. Whatever the reason, no need to go buy a whole new FermZilla! Just pick up one of these fresh replacement tanks and your conical fermenter will be good as new! Pressure Stress If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple: Fill the tank to the brim with water Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher Pressurize the tank to 4 BAR (58 psi) Check for leaks, then replace the Red PRV when finished If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla. General Care Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank. KegLand Part Number: KL28257 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.
Give your Chronical insulation to help with maintaining fermentation temp and assist with cold crashing. Specifically sized for the 10-clamp version of the 1/2 bbl unit.
It may just look like an oversized keg at first glance, but the 1 bbl Kegmenter can do so much more! These stainless steel vessels are perfect as a pressure fermentation vessel, storage brite tank, or even a large-batch home still. Welded tri-clamp openings offer versatility for rigging up this unit however you see fit. Large 4" tri-clamp opening at the top and two 2" tri-clamps ports at the bottom. The large 4" opening at the top makes it easy to get inside the keg for cleaning, and the 2" ports at the bottom can be fitted with valves, heating elements, or other TC accessories and fittings. The kegmenter is well suited for use as a fermenter, brite tank, or top-up barrel. The 1 bbl Kegmeneter comes with end caps and clamps to plug the bottom ports, and a pre-drilled 4" cap for the top opening with a stopper and airlock included. You also have the option to use the Ball Lock Post lid with floating dip tube, which can be used for pressure fermentations or transfers. Also a 4" x 2" TC reducer would allow for adding a Reflux or Pot Still for distillation. Also consider the Kegmenter Hop Bong Pressure Pack which allows for oxygen-free dry hopping and also features ball lock posts for Gas & Liquid. Specifications: Volume: 1 bbl (31 gal) Working Pressure: 3 bar (43.5 psi) Made from stainless steel 41" H x 15.5 Ø Kegland Part number: KL04541
Want an easy-to-use, stainless vessel that ferments and carbonates? This 29L/7.6 Gallon keg has been modified to allow you to do both! The top is fitted with a large 4 inch tri-clamp lid with two ball lock posts and a pressure relief valve. You can use this vessel to ferment, carbonate, serve, or push the beer through a filter. The posts are recessed which allows you to stack these kegs up to 4 high. A 4" T.C. end cap with pre drilled hole is also available (H691), which can be paired with a #3 stopper and airlock. Also consider the Kegmenter Hop Bong Pressure Pack which allows for oxygen-free dry hopping and also features ball lock posts for Gas & Liquid. Depending on how long it will take to consume the finished beer, we recommend using two kegmenters, one for fermentation and one for carbonating and serving. After fermentation, there will be a large trub cake at the bottom of the vessel. Leaving finished beer on the trub for too long (2-3 weeks) may eventually lead to off-flavors. Check out our ball lock jumper line (KEG575) to easily transfer from one kegmenter to the other. Also consider our beer filter kit (FIL40), which will allow you to filter the beer during transfer. Features: Rated up to 2.5 BAR (36 psi) 4" T.C. lid with ball lock posts Floating dip tube Stainless steel 1.8 mm thick Use: As a stainless steel fermenter that is easy to clean Great choice for 5 gallon fermentations Easy to pressurize the kegmenter after fermentation to push through a filter and into another keg Fermenting under pressure, allowing CO2 to exit via the relief valve, reduces esters and fusel alcohol production allowing you to ferment at warmer temperatures Distillation - with the addition of a T.C. reducer and condenser (H701 / DS120 / DS130) As a cellar keg for topping up barrels Warning: Always depressurize keg before removing lid. Does not include spunding valve shown in example photo. Please see FIL42A. Kegland Part number: KL05906
This is a premium black neoprene jacket, tailor-made for the 1 bbl MB Conical Fermenter. Made from 6mm neoprene with black fabric on both sides. Perfect for insulating the conical and using alongside our Reactor Rods.
Heavy-duty HDPE plastic fermentation and stoarge tank
Made from food-safe materials with extra thick walls to preserve the aroma of your beverage
Rotating plastic spigot eliminates the need to use an auto-siphon or racking arm to transfer liquid
Wide top port opening for easy cleaning
Airlock & stopper included
Made in Germany by Speidel
The future is here today, and the future is HDPE Fermentation & Storage Tanks from Speidel. Made in Germany from nothing but undyed and food-safe plastic, these tanks are produced with particularly thick walls which preserves the aroma and the alcohol for a markedly long time. The stable carrying handles have been tried and tested for decades and are extremely durable.
Are you tired of carboys? Hate siphoning to transfer? Wish you could ferment larger batches in a single container? Sick of lifting 50lbs by a small metal handle? Done with worrying about shattered glass, injury and lost product? Well then have we got the solution for you!
These heavy duty plastic tanks offer a fantastic fermentation & storage solution at a great price.
Key Features:
Heavy duty HDPE construction is durable and resists oxygen transfer. None of the risks of working with glass.
Small footprint makes them easy to store - take better advantage of the space you have to dedicate to wine & beer making.
Built-in handles make these tanks easy to move, even when full.
Large lid opening makes them easy to clean by hand - say goodbye to your carboy brush!
All ports seal with gaskets and the vessel can be fully sealed for long-term storage.
Includes a spigot and oversized 2-piece Speidel airlock.
Designed and manufactured in Germany by Speidel, the makers of our legendary commercial wine tanks
Suggested Applications:
12L: Perfect for storing small lots, making experimental batches and taking some of your beer or wine along with you to your next party.
20L: Ideal for secondary fermentation and storage of 5 gallon batches.
30L: The vessel for fermenting wine kits and 5 gallon batches of beer with plenty of headspace and no need for a blowoff tube.
60L: Perfect for fermenting larger batches of wine or 10 gallon batches of beer in a single container! Only 4" larger in diameter than a 6.5 gallon carboy!
120L: Ferment & Store large batches of anything - your creativity is the only limit!
Approximate Dimensions: 12 in. Diameter x 16.5 in. Height (w/out airlock in place). Mouth is 4.75 in. wide. Note - The maximum temperature that these plastic fermenters can handle is 140F.
FAQ:
Can filled containers be carried by the handles?
Depending on the weight—barrels up to 30L are no problem—60L is the limit and should not be carried when completely full. The handles have a weight capacity of 30kg (66 lbs).
Is there an upper limit on the alcohol content of the stored liquid?
In principle, there is not. However, it should be noted that the higher the alcohol content, the faster the seals and, to a lesser extent, the tank itself will wear out.
Up to what temperature can the containers be used?
For short periods of time the containers can withstand temperatures of up to 80°C (176°F). This temperature should not be exceeded. For longer periods of time the containers can be used at temperatures up to 60°C (140°F).
Control your fermentation temperatures with Cool Brewing's simple, yet innovative, insulated fermentation bag. This is the 2nd generation Cool Brew bag, which has made cold fermentations even easier! Fermenting your homebrew at the right temperature is one of the critical factors in making good beer. Let the temperature get too warm, and your beer will taste 'rough' as the soft malt and vibrant hop flavors dissapear! Typically an advanced homebrewer would want to get a spare refrigerator or even a MoreBeer! Cooled Conical to control fermentation temperatures, both those options either take up a lot of space or can cost a fair amount of money. The Cool Brewing Bag allows the apartment brewer, those who have space constraints, or the brewer on a budget a great option to control fermentation temperature and make great beer. Cool Brewing's Fermentation Cooler is designed specifically to accommodate standard 6.5, 6 or 5 gallon fermenter. You freeze a 2 liter soda bottle with water, or similar, and place in the fermentation bag with your fermenting carboy. Also works great with the Ss BrewTech Brew Buckets! The typical desired ale fermentation range is on average around 62-72° F. For a typical 5 gallon batch (1) frozen 2-liter bottle should lower wort temperature around 5 degrees, while using (2) 2-liter bottles will lower wort temperature around 11 degrees for 24-36 hours. Of course your exact results might vary but you can adjust the amount of ice you use as you go. The manufacturer has found they can cool the wort temperature up to around a 30-35° drop from ambient room temperature. On the flipside, add a Fermwrap and temperature controller to the setup, and you've got a heated fermentation temperature accurate to within 1° F! The Cool Brewing Fermentation Cooler is sealed, insulated and 100% waterproof so it will efficiently and neatly keep your temperatures in check. When you’re done, the Cool Brewing Fermentation Cooler easily folds up for storage until the next brew day! Cool Brew Features: Up to twice as efficient and cleaner then homemade swamp coolers
Much less expensive than custom kegorator or keezer set up's that cost $100's of dollars.
Cool Brewing Cooler will work with multiple sized fermenters.
100% waterproof so will not leave condensation.
It folds up for easy storage when not in use or travel.
Will work great in condos and warm climates where you need a swamp cooler even for Ale’s!
Contains the mess of any fermentation blowouts
Inner dimensions: 20.5"D x 25.5"H
Want an easy-to-use, stainless vessel that ferments and carbonates? This 58L/15.3 Gallon keg has been modified to allow you to do both! The top is fitted with a large 4 inch tri-clamp lid with two ball lock posts and a pressure relief valve. You can use this vessel to ferment, carbonate, serve, or push the beer through a filter. The posts are recessed which allows you to stack these kegs up to 4 high. A 4" T.C. end cap with pre drilled hole is also available (H691), which can be paired with a #3 stopper and airlock.
Also consider the Kegmenter Hop Bong Pressure Pack which allows for oxygen-free dry hopping and also features ball lock posts for Gas & Liquid.
Depending on how long it will take to consume the finished beer, we recommend using two kegmenters, one for fermentation and one for carbonating and serving. After fermentation, there will be a large trub cake at the bottom of the vessel. Leaving finished beer on the trub for too long (2-3 weeks) may eventually lead to off-flavors. Check out our ball lock jumper line (KEG575) to easily transfer from one kegmenter to the other. Also consider our beer filter kit (FIL40), which will allow you to filter the beer during transfer.
Features:
Rated up to 2.5 BAR (36 psi)
4" T.C. lid with ball lock posts
Floating dip tube
Stainless steel 1.8 mm thick
Use:
As a stainless steel fermenter that is easy to clean
Great choice for 10 gallon fermentations
Easy to pressurize the kegmenter after fermentation to push through a filter and into another keg
Fermenting under pressure, allowing CO2 to exit via the relief valve, reduces esters and fusel alcohol production allowing you to ferment at warmer temperatures
Distillation - with the addition of a T.C. reducer and condenser (H701 / DS120 / DS130)
As a cellar keg for topping up barrels
Warning: Always depressurize keg before removing lid.
Does not come with spunding valve show in example photo. See FIL42A.
Kegland Part number: KL04572
This 30W Heating Belt will gently warm your fermenter without creating major hot spots. Heating belts are often chosen over heating pads for the simplicity of adjusting the height of the belt on your fermenter to increase or decrease the heat transfer. And they're especially useful for smaller vessels where a heating pad would be simply too large.
For the best results, pair the Heating Belt with a temperature controller so that heating is only provided when your fermentation drops below your set point. If you're using a fermentation chamber or other form of chilling, the temperature controller will be able to switch between heating and cooling as needed.
Comes with a standard 2-prong US style 110V plug. Please disregard the example photo that shows an AU style plug.
KegLand Part Number: KL01953
Yeast across the World have a new best friend, the OxyWand™. Insert the areation wand into your fermenter and pump in thousands of microscopic oxygen bubbles for 1-2 minutes to improve the health of your yeast. Healthy yeast produce amazing flavors and have the stamina to completely finish fermentation.
That is not the only reason yeast love the OxyWand™. Yeast hate to compete with bacteria and you hate to drink them. Sintered stainless stones are made of tightly compressed stainless steel powder to create a porous block through which oxygen can flow. This micro maze is also the perfect environment for bacteria to live in after the stone has been used once in wort. That is why we love to boil our stones prior to use. The stone on the OxyWand™ is connected via a 1/4" flare fitting and can easily be removed and cleaned after use and then boiled before your next brew day.
The assembly is 26" long and will easily reach the bottom of glass carboys, dropped into stainless conicals, Speidel fermenters, etc. The 2 micron size stone works well with both compressed oxygen or aeration pumps. You will want to use 1/4" tubing. See the recommended regulator below to connect to disposable style compressed oxygen cylinders available from your local hardware store. See the high-pressure, deep water style air pump to use with regular air.
The advantage of using compressed oxygen to oxygenate is speed - you can oxygenate your wort in 60 seconds as opposed to 30-120 minutes with aeration. The advantage of using a pump for aeration is cost - you never have to buy compressed oxygen cylinders.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
PLEASE NOTE: The supplier of this product has temporarily halted shipments to addresses within the state of California. If you are a CA resident, please note your order will not be fulfilled and will ultimately be canceled. We hope to have this issue resolved with the supplier as soon as possible.
The Glycol Chiller Adapter works in a similar way to the GF30 Conical Fermenter but instead of the built-in cooling sleeve and heating element, it uses a stainless steel cooling coil and a heating pad to control the temperature of almost any fermenter.
The cooling coil is connected to the Glycol Chiller and immersed in the fermenter. The heating pad is attached to the side of the fermenter using hook and loop tape. A temperature probe is also attached to the fermenter and the GCA will then regulate the cooling, or heating, as required.
The GCA connects to the Grainfather App so you can control your fermentation temperature on the go.
Included in the GCA Kit:
GCA Controller
Heating Pad (12V 30W)
5m Cooling Coil
Hose
Rubber Bung
Velcro Hook Strip x 4
Hose Clamps x 2
Rubber Bung Stoppers x 4
10 BBL Unitank Fermenter (Short Tank)
Built for brewers who need full 10-barrel capacity with less overhead clearance. This short-profile conical fermenter packs everything you need for fermentation, conditioning and carbonation into one vessel: a side-mounted oval manway for easy cleaning access, a 6" top hop port for dry hopping, a built-in CO2 carbonation stone, and four glycol jacket ports for precise temperature control.
Key Features
Short-profile design – 89.4" (2,270 mm) overall height (including blowoff pipe) fits brewhouses with lower ceilings.
Dual-wall construction – 51.2" (1,300 mm) inner vessel inside a 57.5" (1,460 mm) outer shell.
Glycol-jacketed – four 3/4" FNPT glycol ports (inlet/outlet pairs) for jacket cooling.
Side-mounted oval manway – 580 × 480 mm opening for easy access during cleaning and inspection.
6" top hop port – large tri-clamp opening for fast, easy dry hopping.
Carbonate in the tank – 1.5" tri-clamp CO2 carbonation stone port.
Full instrumentation – pressure gauge, thermometer, thermocouple well and sample valve.
Built-in CIP and blow-off – dedicated CIP inlet with internal spray ball, plus a 1.5" blow-off arm.
Pressure/vacuum relief valve (PVRV) for safe operation.
Separate yeast and beer outlets – 2" yeast dump at the cone bottom and a 1.5" racking arm beer outlet.
Sanitary tri-clamp fittings throughout.
Dimensions
Capacity
10 BBL
Overall Height
89.4" (2,270 mm)
Outer Shell Diameter
57.5" (1,460 mm)
Inner Vessel Diameter
51.2" (1,300 mm)
Leg Diameter
5.2" (133 mm)
Manway
Side-mounted oval, 580 × 480 mm
Ports & Fittings
Port
Size
Connection
Tube Size (OD × wall, mm)
Yeast Outlet
2"
Tri-Clamp
Ø50.8 × 1.5
Beer Outlet (Racking Arm)
1.5"
Tri-Clamp
Ø38.1 × 1.5
CIP Inlet
1.5"
Tri-Clamp
Ø38.1 × 1.5
Manway
Ø580 mm
Welded
580 × 480 × 133
Pressure Gauge
1.5"
Tri-Clamp
Ø38.1 × 1.5
Thermocouple
1/2"
FNPT
NPT 1/2"
Thermometer
1.5"
Tri-Clamp
Ø38.1 × 1.5
Sample Valve
1.5"
Tri-Clamp
Ø38.1 × 1.5
Pressure/Vacuum Relief Valve (PVRV)
1.5"
Tri-Clamp
Ø38.1 × 1.5
Hop Port
6"
Tri-Clamp
Ø152.4 × 2
Top Port
4"
Tri-Clamp
Ø101.6 × 1.5
Blow-Off Arm
1.5"
Tri-Clamp
Ø38.1 × 1.5
Glycol Ports (×4)
3/4"
FNPT
NPT 3/4"
CO2 Carbonation Stone
1.5"
Tri-Clamp
Ø38.1 × 1.5
Smooth, ribless design prevents yeast and bacteria buildup, making sanitation a breeze Punted bottom and conical top promote sediment collection and reduce oxidation during storage Extra-wide 4" mouth opening simplifies filling, additions, and cleaning Constructed from heavy-duty, virgin PET plastic without plasticizers Made with food-grade and BPA-free materials The Fermonster is a brand new fermenter designed specifically for fermentation. MoreBeer! gave product feedback for over 2 years of development and we think they nailed the design. The large lid allows for easy filling and makes hop or oak additions a breeze. The smooth sides are fantastic for sanitization - no ribs or texture to collect yeast or bacteria. The punted bottom allows sediment to collect to the sides so that you can siphon liquid from the center. Because they are made from virgin PET plastic they nearly unbreakable and a lot safer than similar glass carboys. These ported versions come with our plastic spigot (FE347), allowing for easy racking and sampling! Made from heavy PET plastic, the same material used in 2 L soda bottles, which is nearly impermeable to oxygen penetration. Due to the thickness of the material and the overall geometry the Fermonster does not require ribs or dimples for stability. That results in a super smooth interior surface that reduces yeast and sediment buildup making it the easiest to clean, most sanitary PET carboy on the market. The huge 4" opening makes filling a breeze, and cleanup is as easy as wiping down the inside. These fermentors are completely air-tight and the lids sealed tight with an O-Ring. Additional O-Rings and Lids both with and without holes are available for purchase, see our You Might Also Need items below. Features: 4" inner diameter wide mouth carboy - easy to clean! Food grade PET plastic construction is nearly impermeable to oxygen penetration No hard to clean dimples or ribs Punted bottom O-Ring and Lid with one hole is included (Fits #10 Stopper) Additional O-Rings and Lids available Weight: 0.6 lbs Temperature Limit: 140° F Height: 9.45 inches Diameter: 6.7 inches Completely taste and odor free Perfect for Beer, Wine, Cider, Mead, Kombucha or any other fermented beverage! Thick walls for better oxygen barrier.
This is a premium black neoprene jacket, tailor-made for the 2 bbl MB Conical Fermenter. Made from 6mm neoprene with black fabric on both sides. Perfect for insulating the conical and using alongside our Reactor Rods.
1.5" T.C. carbonation stone for 1 & 2 bbl MB Pro conical fermenters and brite tanks.
Specifications:
2 micron
Overall Length: 7"
Single-piece design
Made from Stainless Steel
This clean in place spray ball is designed to attach to an independent CIP pipe inside a conical fermenter or brite tank. We recommend using it with a pump capable of 29 psi or higher.
1.5" tri-clamp
Made from 304 stainless steel
ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
Variable capacity tank well-suited for fermentation, wine aging, kombucha, pickling, and other applications
Floating lid can be positioned as needed to match the volume of the liquid you're working with
Proprietary rubber lid gasket allows for a superior seal compared to traditional gaskets, providing better protection for your wine
Conical-shaped complete drainage bottom for maximum product yield and easy cleaning
Made from 304 stainless steel with ultra-high-quality laser welds
Made in Germany by Speidel
We are is proud to present our line of premium quality stainless steel tanks. Built in Germany by Speidel, the world-class traditions of German engineering and craftsmanship are reflected in these tanks. And, after examining tanks built by every major manufacturer worldwide, we can safely say that when it comes to features, quality and price, these tanks represent the very best value available in stainless steel wine storage.
Note: These stock tanks are outfitted with two male threaded fittings which will accept either a Speidel Sample Valve or a Thermowell. One fitting will come capped and the other will come equipped with a thermometer.
Speidel Quality Features:
Interior Finish - Speidel tanks feature an ultra-smooth 2R rated interior surface which effectively resists the build-up of tartrate residues. Clean your tanks with cold water after cold stabilization! Say goodbye to harsh cleaning chemicals and expensive CIP systems!
Weld Quality - Speidel's robotic-arm laser welders create flawless stainless to stainless junctions that look and feel more like a taped fabric seam than a traditional weld. Ultra high-quality welds leave no chance for residual product to harbor spoilage organisms.
Thickness - Speidel tanks are designed to be the correct thickness for the tank's total volume.
Complete Drainage Bottoms - All Speidel tanks are outfitted with conical, pocketed bottoms for total drainage, which maximizes product yield at rackings and makes cleaning a snap. *Please note that smaller, flat-bottomed tanks do not feature total drainage bottoms.
Tri-Clamp Valve Ferrules - All Speidel tanks come configured for use with Tri-Clamp (TC) style valves and fittings. Tanks up to 1600L capacity are outfitted for use with 1.5in TC. Other sizes and custom configurations are available at additional cost upon request. **Please Note: TC valves not included. Please inquire with your sales associate for pricing on TC valves and fittings.
Rubber Lid Gaskets - Rubber gaskets are much thicker than the traditional clear vinyl gaskets, which along with their extruded manufacturing process provide a much better seal with the tanks wall. They're seamless and more oxygen resistant than the clear gaskets. That means better protection for your wines!
Warranty - Speidel-Behaelter, GMBH backs up each and every tank with an industry-leading 25 year warranty against defects in materials or workmanship. And, as a 5th generation manufacturer, you can be confident they'll be around to honor that warranty should the need arise.
Tank Dimensions - 630mm D x 1384mm H (24.8" D x 54.48" H) (Lip Ø is 26.378" )
Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.
3.5 BBL Tallboy Fermenter
Model Number: BEPS-FV-3.5BBL-Skinny-Group
Save space in your brewery with our new Tallboy Fermenters! Easily fits through a standard 36″ door opening.
Designed for compact spaces, all valves and accessories are front-mounted for easy use and close spacing between tanks.
Key features include:
15 psi design pressure
14-gauge, fully-welded, 304 stainless steel exterior shell with #4 brush
11-gauge, 304 stainless steel interior shell
Interior finished to Ra 0.8 micron sanitary finish and passivated
60-degree cone bottom, jacketed
Rotating rack arm with butterfly valve and cover
Bottom dump 1.5″ tri-clamp fitting with butterfly valve, elbow, and cover
Sample valve
CIP arm with spray ball and piping
Blow-off port
Vacuum and pressure relief valve
2″-thick polyurethane insulation for cooling jacket and cone
Large 17″ diameter top hatch
3″ dial thermometer
Pressure gauge
Specifications
Specification
3.5 BBL Tallboy
Height
83″
Width
31.5″
Empty Weight
440 lbs
Gross Volume
148
Net Volume
130
% Head Space
20%
Pressure Rating
15 psi
Glycol Jacket Pressure Rate
3 bar = 43.5 psi
Insulation Thickness
60mm
Manway Location
Top
Leg Support
Leveling Feet
WARNING: This product can expose you to chemicals including Nickel (Metallic), which is known in the State of California to cause cancer and reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in late December.
The Brewtools MiniUni™ series fermenters are high-quality, affordable and flexible tanks for fermentation, storage and serving beer
The Plus models feature a built-in cooling jacket for maximum cooling power when paired with a glycol chiller
Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use
Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup
Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe
All valves, fittings, and gaskets come included
The MiniUni™ is a series of high-quality, affordable and flexible tanks for fermentation, storage and serving beer and endless other applications like water heating, cleaning liquid storage, HERMS setups, etc. The Plus-model also has a cooling jacket with 3/8" NPT threaded ports and two 1.5" T.C. ports in the front. They can be kept in the included base, or installed on the wall with the included wall bracket. With the optional pressure kit, you can utilize the 2 bar (30 PSI) pressure rating for fermentation and carbonation.
Use them to build your setup, they will last a lifetime! And as always, Brewtools appreciates any feedback or requests for accessories.
Key Features:
PureBlast™ surface inside and out which eliminates the use of wax and polishing compounds and does not require passivation
Easy cleaning with a 4" T.C. top port and 2" T.C. bottom port
Pressure rated for 2 bar / 30 PSI.
Wall bracket included
Cooling jacket with 3/8" NPT ports
Two 1.5" T.C. ports
If you want to raise the MiniUni base and make room for an elbow with a butterfly valve or other accessories, check out the MiniUni™ Leg Kit.
MiniUni tanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party.
Specifications:
Packaging size: 13.3" (w) x 13.7" (d) x 30.3" (h)
Net weight: 31.3 lbs
Gross weight: 34.8 lbs
Tank diameter (inside): Ø11"
Max volume: 7.9 gal
Cone volume: 0.4 gal
Material: 1.5mm stainless steel (SS304)
Operating pressure: 1.0 bar / 15 PSI
Max pressure: 2 bar / 30 PSI
In the Box:
MiniUni™ Tank
Base with silicone gasket
Wall bracket and wall support
Wall bracket safety pin
Composite T.C. adapter 4" to 34mm
Airlock, 3-piece with holder
4" tri-clamp
2" tri-clamp
1.5" tri-clamp (2)
2" T.C. blind cap
1.5" T.C. blind cap (2)
T.C. gaskets
For User Manuals and support, please follow this link to Brewtools Docs.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
Replacement power adapter and cord for the Grainfather GF30 Conical Fermenter (US).
This is a 304 stainless steel blow off tube for Ss Brewtech 1/2 barrel Chronical fermenters. Fits perfectly on the 3" TC dome lids and comes with a relief valve built into the cane. 3" TC gasket and clamp not included.
The Hop Bong is a versatile pressurizable tri-clamp accessory, capable of not only dry hopping oxygen purged hops into fermenters, but also as an inline carbonation/oxygenation accessory. Load up the Hop Bong, flush it with CO2, purge out oxygen with the handy PRV on top, then simply open the Butterfly Valve to inject your beer with a 6 oz payload of dry hops.
If you're an existing FermZilla Conical or All Rounder user and you already own the Pressure Kit with 2x Ball Lock Caps and floating dip tube, check out the Hop Bong Upgrade Kit.
The 3 Pieces of the Hop Bong Pressure Pack:
Pressure Kit
The Pressure Kit includes two Ball Lock Caps with the Floating Dip Tube and Filter Attachment. These pieces allow you to pressure transfer finished beer out of the fermenter into kegs or a bottling bucket, or you can carbonate and serve beer directly from the FermZilla.
Tri-Clamp Pressure Lid
Replacing the standard lid with the FermZilla Tri-Clamp Pressure Lid provides you with a 2" T.C. port at the top of your fermenter. This will give you an opening to add dry hops or other additions without needing to remove the entire lid. Take off the butterfly valve to add your yeast pitch, and when you're ready to add flavoring additions when fermentation is complete, drop them in oxygen-free via the Hop Bong. PCO1881 threaded ports are there for your Ball Lock Caps, as well as undrilled ports for an optional Thermowell and/or Temp Twister cooling coil.
Hop Bong
Load up the Hop Bong and add CO2 to purge your hop charge of oxygen. This kit comes with a third Ball Lock Cap to introduce CO2 directly to the Hop Bong, as well as a pull ring PRV to release pressure and purge oxygen. Once you've flushed your hop charge with CO2, open the butterfly valve to inject your beer with up to 6 oz of hop pellets.
Hop Pellet Capacity: 150–180g (5.2–6.3 oz)
Kit Includes:
FermZilla 2" T.C. Pressure Lid Starter Kit
2" Hop Bong
2" FermZilla Tri-Conical Butterfly Valve
Floating Dip Tube
Weighted Mesh Filter Attachment (KEG6571)
Red PRV & PCO1881 Cap Combo
Yellow Ball Lock Cap
(2) Red Ball Lock Caps
(2) 2" Tri-Clamps
(2) 2" Silicone T.C. Gaskets
KegLand Part Number: KB10897
Installation Note: For best performance, ensure there is not an excess amount of slack when the silicone dip tube is installed and shorten it if needed. With the floating dip tube installed on your empty FermZilla, you ideally want the dip tube to hang freely with just enough length for the end of the dup tube to touch the bottom of the tank.
Warning: Always depressurize your system COMPLETELY before removing fittings from your fermenter.
The ultimate control & precision of your fermentation process. Equipped with four built-in temperature controllers and pumps, this advanced chiller enables you to independently regulate the temperature of multiple separate fermentation vessels simultaneously, ensuring optimal conditions for different batches or styles of beer, making it a game-changer for homebrewers.
4 Built-in pumps and digital controllers
Control multiple fermentation temperatures independently Fill with 20% glycol solution for optimal chilling performance Cold crash with good insulation Perfect complement to BrewBuilt X-Series Conicals The IceMaster Max 4 is designed to cool fermentations in small vessels. It features 4 built-in submersible pumps with independent digital temperature controllers and can be used with any vessel that has a glycol jacket or submersed cooling coil/rod. Each controller includes a temperature probe that should be inserted into a thermowell in your vessel or can be taped to the outside of the vessel if you don't have a thermowell. The digital controller then measures the temperature of your tank and turns the submersible pump on or off to cool to your desired set temperature. Up to four tanks can be controlled separately with one IceMaster Max 4. Compatibility The IceMaster can be used with any fermenter that has a built-in cooling jacket, added CoolStix, or a submersed cooling coil. It works well as the cooling source for the following systems and fermenters. BrewBuilt Jacketed Uni Conical - we recommend one Insulated Tubing Kit for each tank. These kits feature "dry break" quick disconnects that prevent glycol loss and the insulated tubing will increase chilling efficiency and eliminate line sweating from condensation. CoolStix - CoolStix can be added to a wide range of carboys, fermenters, and tanks and the IceMaster works really well in combination. Each CoolStix is available with or without a pump kit; for use with the IceMaster Max 4 you will only need the CoolStix and some tubing to connect it to the chiller. Ss Brewtech Fermenters and Brites - Ss BME Chronicals, BME Brites, and Unitanks come with cooling coils and neoprene as standard. The optional chilling FTSs will not be needed for use with the Max 4. The cooling coil for standard Ss Chronicals and Brew Buckets are not sold a la carte and must be purchased with a submersible pump, which is not needed for the Max 4. For standard Chronicals and Brew Buckets you might consider the IceMaster 100 for cost savings. Spike Conical with Optional Cooling Coil - the cooling coil for Spike CF series conicals is available for purchase independently from the TC-100 cooling system. For use with the Max 4 you will only need the coil and some tubing to connect it to the chiller. Speidel Tanks with Optional Cooling Jackets - You will need two lengths of tubing to connect the chiller to each tank. Grainfather Fermenters - Grainfather fermenters have standard cooling jackets. You will need two lengths of tubing for each fermenter. Blichmann Fermenators with Optional Cooling Coil - You will need two lengths of tubing for each Fermenator. Capacity It is always difficult to determine exactly how many tanks can be chilled at one time as it depends on what is happening in each tank, if the tank is insulated, and what the ambient temperature is. Cold crashing always requires the most energy and requires tank insulation. We have experimented with capacities and can provide this general guide based on a 75°F ambient and neoprene insulation. Neoprene provides a modest amount of insulation so you would obtain better results using Armaflex or a higher R rated insulation. Capacity calculated at cold crashing to a target temperature of 38°F while the ambient temperature is 75°F with neoprene insulation (double tank capacity for ale fermentation temperature control): 2 - 1BBL (31 Gallon) Jacketed Tank 2 - 1/2BBL (15-20 Gallon) Tanks 3 - 10-14 Gallon Tanks 4 - 5-7 Gallon Tanks Set Up In order to hook up the IceMaster to your fermenter or tank's cooling system, you will need 2 lengths of tubing per vessel. All tubing connections should be secured with hose clamps. Length 1: Barb of 1st bulkhead (IN) to cooling system outlet
Length 2: Barb of 2nd bulkhead (OUT) to cooling system inlet
Specifications: 4 built-in submersible pumps with independent digital controllers Pump controllers read in °F/°C Temperature controller reads in °C Labeled IN and OUT stainless bulkheads with 3/8" OD barbs Tank Capacity: 30L/8 Gal. Water Capacity Compressor: 3/8 HP Cooling Capacity: 780 Watt/2600btu/0.26 ton Refrigerant: R134a Voltage: 110V (3.6 amps) Dimensions: 16.1" x 16.1" x 26" Wheels included CE Certified Max Head: 21.3 ft (6.5 m) Warning: Do not set the reservoir temperature controller lower than 28°F (-2ºC). Running the unit below this temperature may negatively affect the unit's efficiency and has the potential to freeze beer which may impact the finished beer's flavor.
Due to high demand, some of these items are currently out of stock but available for pre-order. Please check status notes below when selecting a size option to see if it is In Stock or tagged as PreBook. We will automatically ship this to you when we receive more inventory.
Absolutely EVERYTHING you need to start brewing!
The complete home brewery kit! Includes everything you need to brew 5 gallons of delicious beer at home!
High quality 5-gallon stainless steel kettle perfect for brewing
Fermonster brand brewing fermenter is clear so you see fermentation activity and eliminates the need to siphon with built-in spigot
Step-by-Step instruction pamphlet fine-tuned over 20 years for easy success
Your choice of recipe kit included
Make brewing fun and easy with our new Deluxe Homebrewing Starter Kit only from MoreBeer!. This beer brewing starter kit includes the nearly indestructible Fermonster fermenter, a five gallon stainless steel brewing kettle, an ingredient kit of your choice and all the time-tested equipment you need to brew up 5 gallons / 2 cases of beer per batch.
With the Deluxe Homebrew Starter Kit, you can choose from several recipes including the American Ale Hoppy Pale Ale, Irish Red Ale, I Heart IPA, and German Hefeweizen.
The Fermonster Fermenter - A Huge Upgrade Over Standard Buckets or Glass "Carboy" Water Bottles
Unlike buckets or glass carboys, the Fermonster fermenter was designed for brewing beer. It is made from tough, clear, virgin grade PET plastic so you can see the magic of fermentation. Unlike glass it will never break and shatter if dropped. It represents a huge upgrade over traditional buckets because these fermenters are much less likely to get scratched. Scratches can hold bacteria that can cause off flavors in the beer. The Fermonster comes with a built-in spigot that eliminates a long time issue in homebrewing of having to start a siphon to transfer your beer to the bottling bucket after fermentation is over. The large 4" lid allows for easily adding yeast, hops, or other additions. We also really love the molded-in level markers that tell you exactly when you have reached your desired volume.
Five Gallon Stainless Kettle - It's Bigger Than What You Have in Your Kitchen
Over the years we found that many brewers thought they had a big enough kettle. They would go home only to return and buy our five gallon stainless steel brewing kettle. To make brewing easy, we've discounted our five gallon brewing kettle to be able to include it from the start! Plus, because it is made of food-grade stainless steel, you don’t have to worry about any off flavors imparted by your boil kettle.
We Don't Skimp on Cleaning and Sanitizing
Proper cleaning and sanitizing is one of the core tenants of making great beer. Some starter kits utilize an all-in-one cleaner/sanitizer that does neither job well. We’ve included the best-selling sanitizer for brewing, Star San. We also include Craftmeister oxygen-based cleaning tablets that make cleaning your Fermonster Fermenter a breeze.
Other Upgrades That Make Brewing Easier
We’ve also made a few items standard that really make the brew day easier including a thermometer for temperature monitoring and a hydrometer with testing jar for measuring sugar levels. Our reusable mesh bags allow for the easy removal of spent grain and hops at the end of the boil. The included stainless spoon is a really nice upgrade over plastic when you are stirring boiling liquids.
Easy, How-To Instructions & an Actual 800#
We've taught hundreds of thousands of people how to brew in over 25 years. Our instructions are clear and simple to follow and will have you making great beer with batch number one. If you have any questions, call our on-staff brewmasters at 1-800-600-0033. In an age where 800-numbers and real customer service is going away, you can still call us and ask a question.
Recipe Options:
American Ale produces a light colored, hoppy Pale Ale that puts the beloved Cascade hop on full display. Cascade hops are one of the classic American hop varieties, and we love them for their citrus, grapefruit character.
Irish Red Ale is a genre-defying brew that continues to be one of our best-selling kits year after year. You'll love the deep, red color and distinct caramel flavor.
I Heart IPA was inspired by Bell's Two Hearted Ale, a universally adored IPA that features front-to-back hop additions of Centennial. Malt character takes a back seat to the pungent quality of citrus and lemon notes.
German Hefeweizen has a lovely blond color and distinct hazy appearance in the glass. This kit uses 100% Bavarian Wheat malt extract with just a dash of Northern Brewer hops for bittering.
This Kit Includes:
6 Gallon Fermonster fermenter with spigot, stopper and airlock
5 Gallon Stainless Steel Kettle
Food-Grade Bottling Bucket with spigot
Mesh Bags for steeping grain and hops on brew day
Thermometer for easy temperature management
Hydrometer for making key sugar readings
Transfer Tubing
Bottling Wand with shut off valve
Sturdy Bottle Capper
Bottle Caps
Bottle Cleaning Brush
Star San Sanitizer for true sanitization
Large Stainless Steel Spoon for mixing
Craftmeister Cleaning Tablets for easy cleaning
Your choice of recipe kit with yeast included
Everything You Need to Brew in One Box:
This kit includes everything you need to start brewing amazing beer at home, all in one easy to wrap box. With our simple to follow step-by-step instructions and included choice of a delicious recipe kit, you will be brewing up your first batch of beer in no time at all. Don't settle for less when picking your homebrewing kit, pick MoreBeer! because we give you More!
Fermonster Carboy - 6 gal. With Spigot:
The Ported Fermonster is a brand-new fermenter designed specifically for fermentation. MoreBeer! gave product feedback for over 2 years of development and we think they nailed the design. The large lid allows for easy filling and makes hop or oak additions a breeze. The smooth sides are fantastic for sanitization - no ribs or texture to collect yeast or bacteria. The punted bottom allows sediment to collect to the sides so that you can siphon liquid from the center. Because they are made from virgin PET plastic, they're nearly unbreakable and a lot safer than similar glass carboys. Also notice the conical top which reduces surface area if you plan to store beer or wine long term.
Five Gallon Stainless Steel Kettle:
Made of high-quality stainless steel that is anything but cheap. The 0.5-mm thick sides and bottom are more than thick enough for this amount of liquid, and the riveted stainless steel handles on the kettle’s body make it easy to carry, even when filled. This 5-gallon kettle can safely hold up to 3 gallons of wort while boiling, making it the perfect size for brewing right in your own home!
Great Customer Service Since 1995:
As avid homebrewers ourselves, we strive to help new brewers make great beer right from the first batch. We have knowledgeable homebrewers ready to help you 6 days a week (Mon-Sat) on our Customer Service team. Got a question? We are glad to answer it. Have a problem? Let us help you. We’ve built our business on great customer service since we started in 1995. We also offer a vast library of Articles & Videos on numerous homebrewing topics.
You will also need one of the following to bottle or keg your beer:
(48) 12 oz or (24) 22 oz cappable Beer Bottles or a Home Kegging System
Premium quality laser-welded stainless steel sealed tank wine, beer, spirits, cider, kombucha, and other beverages Cooling jacket covers the entire tank of efficient glycol cooling Top hatch provides a large, convenient opening for adding oak or other additions Conical-shaped complete drainage bottom for maximum product yield and easy cleaning Tri-clamp ferrule ports with thermometer and thermowell combo included Made in Germany by Speidel We are proud to present our line of premium quality stainless steel tanks. Built in Germany by Speidel, the world-class traditions of German engineering and craftsmanship are reflected in these tanks. And, after examining tanks built by every major manufacturer worldwide, we can safely say that when it comes to features, quality and price, these tanks represent the very best value available in stainless steel beverage storage. We've found that these tanks work well for beer, wine, spirits, cider, and more! Convenient top hatch makes cleaning and oaking easy. Heavy duty sealing mechanism and thick gasket ensure an air tight seal. The tanks will support a few p.s.i. of pressure, however they are not pressure rated or designed to be used under pressure. The inside is finished to Speidel quality standards. Bottom drain fittings are 1.5" Tri-Clamp. Flat bottom tanks do not have legs; conical tanks come standard with legs. Speidel Quality Features: Full Jacket - Equipped with a jacket that covers all accessible areas of the tank and is designed for an operating pressure of 2.5 to 6 bar. This will allow you to hook it into a glycol system (see our Kreyer Chilly45, GLY410) for complete temperature control! Interior Finish - Speidel tanks feature an ultra-smooth 2R rated interior surface which effectively resists the build-up of tartrate residues. Clean your tanks with cold water after cold stabilization! Say goodbye to harsh cleaning chemicals and expensive CIP systems! Weld Quality - Speidel's robotic-arm laser welders create flawless stainless to stainless junctions that look and feel more like a taped fabric seam than a traditional weld. Ultra high-quality welds leave no chance for residual product to harbor spoilage organisms. Thickness - Speidel tanks are designed to be the correct thickness for the tank's total volume. Complete Drainage Bottoms - All Speidel tanks are outfitted with conical, pocketed bottoms for total drainage, which maximizes product yield at rackings and makes cleaning a snap. *Please note that smaller, flat-bottomed tanks do not feature total drainage bottoms. Tri-Clamp Valve Ferrules - All Speidel tanks come configured for use with Tri-Clamp (TC) style valves and fittings. Tanks up to 1600L capacity are outfitted for use with 1.5 in TC. Other sizes and custom configurations are available at additional cost upon request. **Please Note: TC valves not included. Please inquire with your sales associate for pricing on TC valves and fittings. Rubber Lid Gaskets - Rubber gaskets are much thicker than the traditional clear vinyl gaskets, which along with their extruded manufacturing process provide a much better seal with the tanks wall. They're seamless and more oxygen resistant than the clear gaskets. That means better protection for your wines! Warranty - Speidel-Behaelter, GMBH backs up each and every tank with an industry-leading 25 year warranty against defects in materials or workmanship. And, as a 5th generation manufacturer, you can be confident they'll be around to honor that warranty should the need arise. Tank Features: Volume: Sealed, 1250 L. Open top, 1283 L Manway Jacket: 2.5 m² (4x 1" MPT connections) Complete Drainage Dish Bottom Reinforced Racking valve 2" TC connections Thermometer and Thermowell Combo included Sample Valve included Tank Dimensions: 1000mm D x 2135mm H (39.3" D x 84" H)
The BrewBuilt tri-clamp thermometer features a large 3" face for easy reads and 6" probe for deep penetration into your conical fermenter or T.C. kettle. Dial face reads from 0-220°F and -10-100°C.
3" dial face
6" probe
1.5" T.C.
Reads in °F and °C
For commercial brewery application with a range of 0-2.2 Bar. For homebrew fermenters, see the BrewBuilt® Spunding Valve
Automatically release pressure inside your fermenter during pressure fermentations
Compatible with any stainless steel pressurizable fermenter with 1.5" tri-clamp ports
In-line pressure gauge for easy reference of tank pressure reads from 0-35 PSI
Made from 304 stainless steel and comes fully assembled
This tri-clamp spunding valve provides professional-level accuracy for fermenting under pressure. Attach to any pressurizable stainless steel conical with 1.5" TC ports and set your desired blow-off pressure. A pressure gauge sits in-line from the conical to the spunding valve so you can reference the current pressure inside your vessel at any time. The polycarbonate cylinder that surrounds the spunding valve can be filled with water or sanitizer to keep your tank 100% sanitary throughout the fermentation process.
Not designed for homebrewing conicals where the maximum allowed pressure does not exceed 1 Bar.
The pressure gauge reads from 0-35 psi or 0-0.25 MPa. The spunding valve is scaled in both psi and BAR, up to 32 psi (2.2 BAR).
Comes fully assembled
1.5" tri-clamp connection
In-line pressure gauge
Made from 304 stainless steel
For Your Safety: Never exceed the maximum rated working pressure of your vessel at any time during operation. The fixed-pressure PRV on your conical should always remain in place while using this spunding valve.
Control and power up to two fermenters at different temperatures and fermenting schedules
Use with the GCA Glycol Chiller Adapter to connect to the Grainfather S SERIES range of fermenters or most other fermenters
Sleek and compact design with LED control display
Compatible with the Grainfather App when connected to a Grainfather G SERIES fermenter or the GCA for managing your fermentation from anywhere via Wi-Fi
The Grainfather GC2 Glycol Chiller makes consistent beer every time with accurate temperature control of up to two fermenters, even if they are running at different temperatures and fermentation schedules. Don’t leave your fermentation to chance, leave it to Grainfather.
Control and power up to two fermenters at different temperatures and fermentation schedules with the GC2. By accurately controlling the temperature of your fermentation, you can produce consistent beers, every time.
What's Included:
GC2 Glycol Chiller
Glycol funnel
Silicone tubing for priming pump
Specifications:
Size: 23" x 12.6" x 14.6"
Weight: 71.5 lbs
Capacity: 0.8 gal glycol tank
Power: 110V, 160W