How frustrating is it when hops cause blockage in your poppet, tap, ball valves and practically everywhere else? This really handy little filter can be used on with the Torpedo Keg Buoy or the floating dip tubes included with the Kegmenter and FermZilla Pressure Kit to prevent hops or other solids from getting sucked into the dip tube itself. The 304 stainless 80 mesh is fine enough to filter out hops and many other solids but not so fine that it gets blocked up easily. If you have a FermZilla or stainless Kegmenter this add is a must. Made from HDPE and 304 Grade stainless steel, this product can be boiled or sanitized in the full range of cleaners that we sell. The plastic HDPE is over molded onto the stainless mesh to make a seamless finish. The end cap can easily pop off for cleaning. Kegland Part Number: KL16957
Tired of fishing your picnic faucet out of the dirt or the bottom of your kegerator? This holder from Torpedo fits over most ball lock keg posts and holds your hand faucet in convenient, clean position. Made from stainless steel with the Torpedo Keg logo etched in.
Does not fit pin lock kegs.
304 cast stainless steel ball lock quick disconnect made for high-durability Black ring above the outer bushing to identify the QD for beverage use Compatible with all ball lock style homebrew kegs 1/4" flare thread connection This is a ball-lock type quick disconnect that is constructed from stainless steel for lifetime longevity. This product is for the Black Beverage Out connection on the right, for the White Gas In connection, see our KEG734. 2 1/8" H Please note: the outer bushing on the disconnect is made from chrome-plated brass. All parts that come into contact with liquid are stainless. Kegland Part Number: KL03018
To upgrade your brew system, and make your life easier, thread these QD’s on your kettle, mash-tun, pump and chiller! When used with the male QD, they seal up very well in either flow direction. They will save you time and prevent messes. Just get several silicone hoses of various lengths and put barbed male fittings on either end. Then use them wherever you need to in your system! They are so much easier to use than pushing and pulling the hoses off of barbs. It makes things interchangeable for cleaning, and provides quick installation and removal.
MoreBeer! designed the original stainless QD's for the brewing industry over 10 years ago. The same manufacturer has been machining them for us ever since. The design has certainly been copied but not with consistent quality. That is why MoreBeer! Stainless QD fittings have a near unanimous 5 star review.
Please Note: This product will NOT work with our Brass or Plastic Quick Disconnects.
This will work with any of our H503 and H507 series of quick disconnects. These feature a 1/2" Male National Pipe Thread on the end for easy connectivity to almost anything. The quick disconnect will hold pressure for typical brewing applications when moving liquids at 60 psi or less. 1/2" ID. Gasket temperature range is -40° to 250° F. Open port, does not have shut-off.
This stainless steel ball lock cap features soda bottle threads, allowing you to convert a 1 or 2 liter soda bottle into a convenient travel growler. The ball lock is compatible with both gas and beverage disconnects, so you can charge the PET bottle before you leave the house and dispense on the go. Attach 3/16" or 1/4" ID tubing to the barb to serve as your dip tube and you're all set! These caps also work great for quickly and conveniently cleaning your draft lines. Mix up a small batch of line cleaning solution in a soda bottle, attach the ball lock cap, and then connect it to your beverage line. Place a bucket below your tap to catch the cleaning solution and open your faucet. Then simply turn the bottle upside down and squeeze it to push solution through your line and out the faucet. You can also choose to pressurize the bottle first, but squeezing the solution through is just as effective. Fermenting with the FermZilla? This is the same ball lock fitting included with the FermZilla Pressure Kit and it's also compatible with the FermZilla Collection Container. If you use the collection container to add dry hops, attach one of these caps and you'll be able purge the container of oxygen before opening the dump valve to introduce the hops. Attach some tubing and diffusion stone and you can oxygenate your wort through the collection container as well! Features: Liquid and Gas Ball Lock Compatible Disassembles for Easy Cleaning Made from Stainless Steel 28mm PCO 1881 Threads Please note: The threaded section of the bottleneck must be at least 1/2" long to form a seal. These caps are not compatible with the KegLand 500mL PET Bottles. Kegland Part Number: KL00826
Made by MoreBeer! from 304 stainless steel.
When used in conjunction with the female QD these quick disconnects seal up completely regardless of the liquids direction of flow, while remaining simple and easy to use. This will work with any of our H503 and H507 series of quick disconnects. However, it does not work in conjunction with any of our plastic or brass quick disconnects. These feature a 1/2" Female National Pipe Thread on the ends for easy connectivity to almost anything.
The quick disconnect will hold pressure for typical brewing applications when moving liquids at 60psi or less. 1/2" ID. Gasket temperature range is -40° to 250° F. Open port, does not have shut-off.
We designed the original stainless QD's for the brewing industry over 10 years ago. The same manufacturer has been machining them for us ever since. The design has certainly been copied but not with consistent quality. That is why MoreBeer! Stainless QD fittings have a near unanimous 5 star review.
Please Note: This product will NOT work with our Brass or Plastic Quick Disconnects.
To upgrade your brew system, and make your life easier, thread these QD’s on your kettle, mash-tun, pump and chiller! When used with the male QD, they seal up very well in either flow direction. They will save you time and prevent messes. Just get several silicone hoses of various lengths and put barbed male fittings on either end. Then use them wherever you need to in your system! They are so much easier to use than pushing and pulling the hoses off of barbs. It makes things interchangeable for cleaning, and provides quick installation and removal.
MoreBeer! designed the original stainless QD's for the brewing industry over 10 years ago. The same manufacturer has been machining them for us ever since. The design has certainly been copied but not with consistent quality. That is why MoreBeer! Stainless QD fittings have a near unanimous 5 star review.
Please Note: This product will NOT work with our Brass or Plastic Quick Disconnects.
This will work with any of our H503 and H507 series of quick disconnects. These feature a 1/2" Female National Pipe Thread on the end for easy connectivity to almost anything. The quick disconnect will hold pressure for typical brewing applications when moving liquids at 60 psi or less. 1/2" ID. Gasket temperature range is -40° to 250° F. Open port, does not have shut-off.
The most affordable ball lock quick disconnect we offer!
White color easily identifies the QD for gas use
1/4" barb connection
This white, gas-in quick disconnect comes with a barb for attaching to a beverage line, and its high quality construction creates a sturdy seal that won’t leak gas when in use.
The barb measures 1/4 inch, so it is compatible with either 1/4 inch or 5/16 inch beverage tubing.
Note: Sometiems ball lock fittings can be difficult to get fully seated on a Cornelius keg. We recommend using a quick spray of sanitizer solution to act as a lubricant and giving it a few twists while applying the ball lock.
Kegland Part Number: KL02943
304 cast stainless steel ball lock quick disconnect made for high-durability White ring above the outer bushing to identify the QD for gas use Compatible with all ball lock style homebrew kegs 1/4" flare thread connection This is a ball-lock type quick disconnect that is constructed from stainless steel for lifetime longevity. This product is for the White Gas In connection, for the Black Beverage Out connection, see our KEG732. 2 1/8" H Please note: the outer bushing on the disconnect is made from chrome-plated brass. All parts that come into contact with liquid are stainless. Kegland Part Number: KL03001
The highest quality plastic ball lock quick disconnect available to homebrewers
Built-in check valve to prevent liquid from backflowing into your draft system
Smooth operation—clicks into place on keg posts and is easily removed
Built-in flare washer—no need for a separate nylon washer that is required with stainless steel QDs
CMBecker is an international manufacturer of beverage dispensing solutions for both home and professional draft equipment
Gray plastic clearly identifies the disconnect as the gas in QD
Sleep a little easier knowing this gas in ball lock with built-in check valve has your back. The internal check valve allows gas to flow out, but won't allow backflow of liquid into your gas system. Many manifolds and regulators already feature check valves, but this disconnect will keep liquid from ever entering your gas lines in the first place. Especially handy if you force carbonate your beer using the bev out dip tube!
Why we love it: Because we've had beer shoot back into our gas line and that sucks. At some point you will have a keg that is pressurized more than the pressure in your gas system. This could be caused by different carbonation levels, a keg sitting at room temperature, etc. So for example if the pressure in your keg is at 20 psi and your regulator is set at 12 psi, when you connect your gas in quick-disconnect liquid shoots from the keg into the gas line. Eliminate that possibility with this ingenious fitting.
Features:
Internal Check Valve protects your system from liquid back flow
Made in Germany and assembled in the USA by CMB.
Extremely high quality for years of service.
NSF Approved for Food Grade Service!
Brand new ball lock keg—no need to clean out an old, used Coke or Pepsi soda keg!
Dual rubber handles make it easy to grip, lift, and move the keg when full
Rubber base is less likely to damage flooring in your home or kegerator
Made from 304 stainless steel in and commerical-quality FSSC 22000 Certified facility
This brand-new, corny-style ball lock keg features a molded rubber base and dual-handle top for easy handling and stacking. The comfortable grip handles make it easier to maneuver when full, while the rubber base protects both your floor and the keg itself. This durable keg is constructed from high-quality 304 stainless steel and manufactured in an IFSSC 22000-certified facility.
Features:
Ball lock
130 PSI Operating Pressure
5 Gallon (19 L) Capacity
304 Stainless Steel
Produced in an FSSC 22000 Certified Facility
Dimensions:
Height: 25.75 in.
Diameter: 8.75 in.
Use this fitting to convert 1.5" tri-clamp to Male Quick Disconnect. This fitting is extremely useful when transferring wort from your brew kettle to a stainless fermenter with tri-clamp connections. If you already use female QDs on your transfer tubing, simply connect to this male QD x tri-clamp fitting, rather than having a specific length of transfer tubing with quick disconnect on one end and barbed T.C. fitting on the other.
1.5" tri-clamp
Male Quick Disconnect
Made from 304 stainless steel
ForgeFit® is a brand of rugged, high-quality fittings made from certified 304 stainless steel. Each fitting is backed by our 60-day no-hassle return policy and a one-year warranty from MoreBeer!.
304 cast stainless steel ball lock quick disconnect made for high-durability
White ring above the outer bushing to identify the QD for gas use
Compatible with all ball lock style homebrew kegs
1/4" barb connection
This is Ball Lock Quick Disconnect is constructed from stainless steel for lifetime longevity. 1/4" barb.
This QD is for the Gas In side.
2-1/8" H
Please note: the outer bushing on the disconnect is made from chrome-plated brass. All parts that come into contact with liquid are stainless.
Kegland Part Number: KL02981
Weighted cap design keeps the dip tube submerged, maximizing liquid draw and minimizing air intake for consistent performance Prevents hop material and other sediment from clogging your dip tube, ensuring cleaner beer transfers and samples Works seamlessly with Torpedo Keg Buoys, Kegmenter Floating Dip Tubes, and FermZilla Pressure Kits for diverse brewing setups Made with food-grade HDPE and 304 stainless steel, allowing for easy cleaning and sanitization with common brewing cleaners This handy little filter attachment can be used with the Torpedo Keg Buoy, Kegmenter Floating Dip Tube, or FermZilla Pressure Kit to keep hop material from being sucked into the silicone dip tube. This upgrade accessory is especially helpful if you like to dry hop directly in your keg while serving, or if you want to pull clean samples from your FermZilla or Kegmenter during fermentation when there's still a lot of biomatter in solution. Simply remove the metal tube from the ball float, slip the silicone tubing over the barb, then reattach the ball float to one of three clip locations. Made from HDPE and 304 stainless steel, the filter can be boiled or sanitized with the full range of cleaners that we sell. The plastic HDPE is over molded onto the stainless mesh to make a seamless finish. The end cap can easily pop off for cleaning. This updated version of the original Filter Attachment now includes a weighted cap that helps keep the end of the dip tube pointed down and submerged below the liquid surface level. KegLand Part Number: KL41485
304 cast stainless steel ball lock quick disconnect made for high-durability
Black ring above the outer bushing to identify the QD for beverage use
Compatible with all ball lock style homebrew kegs
1/4" barb connection
This is a ball-lock type quick disconnect that is constructed from stainless steel for lifetime longevity. 1/4" barb.
This QD is for the Bev Out side. See here for the Gas In QD.
2 1/8" H
Please note: the outer bushing on the disconnect is made from chrome-plated brass. All parts that come into contact with liquid are stainless.
Kegland Part Number: KL02998
This is a special 1/4" nut and 5/16" barb that will attach to threaded quick disconnects or other 1/4" male flare fittings and allow 5/16" gas tubing to be attached.
Stainless Steel barb with a chrome plated Brass nut.
The highest quality plastic ball lock quick disconnect available to homebrewers
Smooth operation—clicks into place on keg posts and is easily removed
Built-in flare washer—no need for a separate nylon washer that is required with stainless steel QDs
CMBecker is an international manufacturer of beverage dispensing solutions for both home and professional draft equipment
Black plastic clearly identifies the disconnect as the liquid out QD
This black, beverage out quick disconnect comes with a flare for attaching to a beverage line, and it's made by CM Becker so you know it is high quality.
The flare threads measure 1/4 inch.
Note: Sometimes ball lock fittings can be difficult to get fully seated on a Cornelius keg. We recommend using a quick spray of sanitizer solution to act as a lubricant and giving it a few twists while applying the ball lock.
Automatically release pressure inside your fermenter during pressure fermentations Regulate beer flow during pressurized transfers from fermenter to keg Built-in pressure gauge for easy reference when adjusting the spunding valve Pressure gauge is interchangeable—swap to different pressure ranges that better suit your application Diaphragm spunding valves offer higher accuracy compared to spring & poppet spunding valves Comes complete with ball lock QD, Duotight adapter, and rigid joiner With this complete kit you'll be ready to use the BlowTie 2 Spunding Valve right out of the box. The BlowTie is used to release excess pressure on a pressurized fermenter or from a receiving keg during pressure transfers. This diaphragm spunding valve is much more accurate than the spring and poppet style, and works much better at lower pressures. This version of the Spunding Valve Kit includes the CM Becker Ball Lock QD, often considered the finest quality in plastic ball lock quick disconnects, and an 8 mm Duotight Flare Adapter for connecting to the BlowTie. The BlowTie 2 can also be upgraded with a Digital Mini Pressure Gauge. Pressure Fermentation Pressure fermentation is becoming more and more popular at the homebrew level, but in order to do it safely and accurately, you need a way to release excess pressure. You'll pressurize your vessel to your desired psi, but once fermentation begins and those hungry, active yeast start creating CO2, the pressure inside the vessel will increase. Attach a spunding valve and set it to your desired pressure, and it will blow off when the pressure gets to high and close up again when it's back to your desired psi. Pressure Transfers Even if you don't have a pressurizable fermenter, you may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process. Diaphragm vs. Poppet With the poppet style spunding valve, a spring pushes against a poppet to keep the valve closed. When the poppet lifts up to open, the surface area the gas pushes against becomes larger, and the spring has to work harder to push the poppet down and reseal the valve. This can lead to more gas being released than intended, and the remaining pressure in your vessel may be at a lower psi than your spunding valve’s set psi. Instead of a poppet, the spring inside the BlowTie pushes against a diaphragm, which has an immensely larger surface area. This means the surface area that the gas pushes against while the diaphragm is closed is significantly closer to the surface area it pushes against when the diaphragm is open. This leads to higher accuracy, and the remaining pressure after excess gas is released will be much closer to your set blow off pressure. Kit Includes: BlowTie 2 w/ Integrated Pressure Gauge (0-15 psi) CM Becker Gray Ball Lock Disconnect Duotight Flare Fitting 8 mm OD Rigid Plastic Joiner
If your home draft system is a mix of ball lock kegs and commercial sanke kegs, having a coupler with ball lock adapters is a huge plus. This allows you to have all your draft lines ending in a ball lock quick disconnect, making it quick and easy to swap lines from sanke keg to ball lock.
Note that the gas-in adapter has a small line cut into the body of the adapter where the bev-out adapter is smooth.
The check valves will need to be installed before first use. The silicone check valve is inserted on the side gas-in port and the check ball and ball retainer are inserted on the top bev-out port.
D-style sanke coupler
Stainless body
Stainless probe
PRV rated to 4.5 BAR (65 psi)
An Intertap accessory that converts the spout of an Intertap faucet into a ball lock quick disconnect. One of the most popular uses is being able to connect the beverage side of your counter pressure filler without having to open your refrigerator door.
Compatible with Intertap and NukaTap faucets.
Stainless Steel Construction
Kegland Part number: KL01052
Replacement internal gasket for Torpedo Keg ball lock QDs. This O-ring helps seal off the internals of the QD, resting where the hex head top screw fastens into the body of the QD.
16mm x 2.7mm
This stainless steel hop tube is ideal for keeping kettle additions from clogging your pump or heat exchanger, and works perfectly for dry hopping in a keg or wide-mouth fermenter. Holds approximately 5 oz of pellet hops, allowing some space to permit full extraction of the hop oils. The stainless chain makes it the perfect partner to our Corny Keg Lid with Welded Tab. Hang the tube inside your keg for post fermentation hop, fruit, wood chip, or spice additions. When it's time to remove the hops/adjuncts simply pull the tube out. Works great for timing exactly how long your beer sits on the hops, oak, or other flavoring addition. 2.6" diameter 11.8" tall Made from 304 stainless steel Kegland Part Number: KL05210
Leave your bulky CO2 regulator and cylinder at home! This Mini CO2 regulator uses 74g cartridges for convenient mobile draft dispensing Dial in your ideal serving pressure just as you would with your standard regulator A portable mini-regulator with all the features of a full sized regulator! Perfect for parties and gatherings where you don’t want to haul around a large canister and hoses. A lot of great features packed into a very small package. The regulator has a range of .5-1.5 bars (7-21 psi). This means that, unlike a button-activated CO2 injector that shoots in CO2 at a fixed pressure, the mini-reg allows you precisely dial in pressure and keep it there. It utilizes a disposable 74 gram CO2 cartridge, which is the largest size that can be shipped full. This is a two stage mini-regulator, meaning that it takes the pressure down from 800 psi (cartridge pressure) to a lower pressure and then to your set pressure of around 10 psi. Two stage regulators are the only way to have consistent pressure. One 74 gram cartridge will typically dispense one 5 gallon keg. This is the regulator only. Cartridges and quick disconnect (KEG730) sold separately. Please Note: This product is only eligible for ground shipment in the Contiguous United States. No air shipment or shipment to Hawaii or Alaska.
The mini CO2 regulator does not have an internal check valve. To add a check valve use the regulator with KEG729 or KEG741.
The most affordable ball lock quick disconnect we offer!
White color easily identifies the QD for gas use
1/4" flare thread connection
The gray, gas-in quick disconnect with male flare fitting. Convenient to use, easy to clean.
Find out for yourself why so many brewers prefer to work with flared keg fittings. Because the fitting-tubing junction is threaded, it can be easily disconnected for cleaning without having to clip your line. Also makes swapping between ball lock and pin lock kegs in the same draft system a snap!
Kegland Part Number: KL02967
The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required. Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing. 6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length. Duotight Push-to-Connect These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done! Compact The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines. Overmolded Poppet The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out. Tool-less Disassembly Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects. Extreme Chemical Resistance No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing. Toughness This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough! High Flow The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects. Features: Ball Lock Quick Disconnect - Bev Out Direct connect EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Dissamble by hand for quick and easy cleaning Three sizes available: 6.35 mm (KL24235) 8 mm (KL20749) 9.5 mm (KL20763)
Small hose clamp suitable for 3/16" to 5/8" OD tubing
Go-to clamp for anywhere you need to secure tubing
Made from stainless steel
These Stainless Steel small hose clamps are perfect to keep around as your go-to clamp. Use them anywhere you want to be sure your tubing will stay connected. They are perfect for silicone hoses and hooking up quick disconnects, pumps, or on any system that may need a tight seal. These stainless clamps tighten up better than cheaper ones, and the stainless steel won’t corrode. It’s handy to keep a few spares around, just in case.
Our small clamps will fit hoses with 3/16" through 5/8" OD.
Stainless dip tube and thermowell for Speidel plastic fermenters. Replace your spigot with this dip tube along with a ball valve for a nice spigot upgrade. The 1/2 in. NPT connection can also be used for other attachments such as, quick disconnects, camlock components, or tri clamp. The dip tube uses the stock speidel spigot lock ring and gasket.
1/4 in. barb and 1/4 in. swivel nut for flare fitting connections. If you're connecting to stainless steel or brass, you will also need a nylon flare washer to form a seal. Plastic quick disconnects (QDs) on the other hand, have a built-in washer so the additional nylon flare washer is not needed. The barb and nut are both made from stainless steel. We recommend using 3/16" ID tubing for a tight fit.
This stainless steel ball lock cap features soda bottle threads, allowing you to convert a 1 or 2 liter soda bottle into a convenient travel growler. The ball lock is compatible with both gas and beverage disconnects, so you can charge the PET bottle before you leave the house and dispense on the go. Use the Duotight compatible stem to connect a 8mm or 9.5mm reducer, then attach EVABarrier draft line to serve as your dip tube and you're all set! These caps also work great for quickly and conveniently cleaning your draft lines. Mix up a small batch of line cleaning solution in a soda bottle, attach the ball lock cap, and then connect it to your beverage line. Place a bucket below your tap to catch the cleaning solution and open your faucet. Then simply turn the bottle upside down and squeeze it to push solution through your line and out the faucet. You can also choose to pressurize the bottle first, but squeezing the solution through is just as effective. Fermenting with the FermZilla? This is ball lock fitting is also compatible with the FermZilla Collection Container. If you use the collection container to add dry hops, attach one of these caps and you'll be able purge the container of oxygen before opening the dump valve to introduce the hops. Attach some tubing and diffusion stone and you can oxygenate your wort through the collection container as well! Features: 6.5mm Duotight Compatible Liquid and Gas Ball Lock Compatible Disassembles for Easy Cleaning Made from Stainless Steel 28mm PCO 1881 Threads Please note: The threaded section of the bottleneck must be at least 1/2" long to form a seal. These caps are not compatible with the KegLand 500mL PET Bottles. Kegland Part Number: KL20435
A quick and easy draft tubing setup for dispensing your homebrew!
This Beer Line Assembly has everything you need to hook a line to your keg and pour. Great for when you're out serving brew on the go or for parties. Includes the ball lock beverage-out quick disconnect, 5 feet of 3/16" beverage tubing, a hand held faucet, and two hose clamps.
