You can use pass through shanks for beer entry through the back side of a cooler. Drill a 1" hole through the cooler, insert the shank, and use the two attached nuts to tighten up on the cooler. You will need nuts and nipples of the size line you are working with as well as hose clamps. We do not use pass through shanks in our boxes because we drill a hole that is same size as the line so we can pull it back in when we are traveling. However there might be instances where they would be appropriate. Pass through shanks can also be used to put through the side of a refrigerator to pass a gas line through.
Installation Note: On a fridge there are generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling.
This is a stainless steel shank with chrome plated brass hex nuts.
Dimensions:
3" - Shank Length
3" - Thread Length
1-7/8" - Pass Through Length
Max length with hex nuts at either end
Does not account for nuts/nipples you may install
Male Beer Thread (5/8" BSP)
Kettle Maximizer allows you to pull liquor or wort from below the depth of your kettle's bottom port
Angle straight down in hot liquor tanks to maximize pick up
Rotate to your preferred pick-up height in boil kettles to leave trub behind when transferring to fermenter
The tri-clamp maximizer is recommended for boil kettles and hot liquor tanks with 1.5" T.C. bottom ports. This fitting will allow you to pull liquor or wort from below the depth of your kettle's bottom port without the need to tip your vessel. For hot liquor tanks, point the end of the tube straight down to maximize pick up. For boil kettles, you can rotate the maximizer to position the end of the tube at your preferred height above the bottom of the kettle, leaving room for a layer of trub that will be left behind in the kettle when you transfer wort to your fermenter.
1.5" tri-clamp
Tube Length: 6.5"
Overall Length: 8.18"
Made from stainless steel
Heavy-duty stainless steel lid can be used with a still top or steam condenser
Sight glass disc allows you to watch your boil without having to remove your still or condenser
Easily remove the disc during the hot break or to add hops or other boil additions
Molded grips for easier handling with the lid is still hot
Compatible with 65L BrewZillas and DigiBoils
If you're using an AlcoEngine Still Top or Steam Condenser set with your BrewZilla or DigiBoil, this heavy-duty stainless lid with sight glass is virtually a must-have. Whether distilling or brewing, keeping an eye on your boil will help you stop foaming or boil over issues before they happen. With the standard distillation lid, checking on your wash or wort means removing or tipping the apparatus over to get a peek inside the boiler, which can be a cumbersome (if not dangerous) part of your process. The PPSU sight glass disc can also be easily removed to add hops or other boil additions through the large 3" T.C. ferrule. (Use gloves, it will be hot!)
The 65L lid is designed to be extremely sturdy when using heavier stills and is made with a 4" T.C. ferrule top port. To pair the lid with an AlcoEngine Still Top or the BrewZilla Steam Condenser Set, you can use a 2" x 4" T.C. reducer. (The AlcoEngine Still Tops will also need this single sided bead seal for a secure tri-clamp connection.)
The sight glass disc is made from a special PPSU plastic—an excellent choice for components that are exposed to high temperatures (up to 392°F / 200°C) and corrosive media due to its exceptional chemical resistance, as well as being extremely impact resistant. KegLand decided to use this type of plastic because it also has superior thermal and mechanical properties with the added benefit of being transparent. Intricate parts can be injection molded that would have been near impossible to do with stainless steel or lab-grade glass.
Specs:
4" T.C. top ferrule port
3" T.C. sight glass ferrule
Lid handles with molded grips
Thicker silicone lid gasket for a tighter seal
Includes:
3" PPSU sight glass disc
3" tri-clamp
3" silicone tri-clamp gasket
Silicone lid gasket
KegLand Part Number: KL25829
This is the recommended accessories to get you started using the Brewtools pro systems. The package includes an efficient counterflow chiller, an extra 3-way valve to make you able to choose if you return the cooled wort to the tank creating a whirlpool or pump directly to the fermenter. A third sensor gives you exact measurements of the wort returning from cooling. The necessary fittings and accessories are also included. Included: 1 pcs 3-way ball valve, TC34mm DN15 1 pcs Dip tube, short 1 pcs Counterflow Cooler, Pro 1 pcs O-ring, Viton, 18x14x2mm 5-pack 3 meter Silicone Tube 16x25mm, clear 2 pcs TC Gasket, 34mm, DN15, 5-pack 2 pcs TC34mm to 12mm hose barb 1 pcs TC34mm to 19mm hose barb, sensor holder 4 pcs TC34mm to 19mm hose barb 1 pcs Temp. Sensor, inline, M10 6 pcs Tri Clamp, 34mm 1 pcs TSP, 100g For User Manuals and support, please follow this link to Brewtools Docs.
Perfect for home use with compact keg setups or on the go for mobile dispensing
Compatible with both 16g and 74g CO2 cartridges
Features a 6.35mm Duotight-compatible barb for fast, hassle-free keg attachments
The Duotight Mini CO2 Regulator is a simple, affordable choice for mini kegs and Oxebar keg setups. This compact regulator is designed to work with both 16g and 74g CO2 cartridges, making it ideal for home use or when you're on the go.
With the 6.35mm Duotight-compatible barb you can connect just about anything within a matter of seconds. Simply pair it with the 6.35mm Duotight Ball Lock QD for a quick and hassle-free connection to your kegs. Or, with the Duotight Reducer, you can adapt the regulator for use with the most common and widely used 8mm Duotight accessories.
For additional protection against liquid backflow, you can integrate a check valve along with some hosing to safeguard your regulator. Please note if liquid enters the regulator, it's no longer functional. Be extremely careful with overfilling your kegs or tipping them over when the gas has run out.
The regulator is capped at 30 psi to ensure you do not accidentally over carbonate or exceed your keg's pressure rating. The gauge reads up to 60 psi to account for potential heat expansion so that it does not break the gauge.
Suitable Gas Cartridges:
16g Cartridge 6-pack (KEG993)
74g Cartridge (KEG969)
KegLand Part Number: KL42000
The most affordable ball lock quick disconnect we offer!
Black color easily identifies the QD for beverage use
1/4" barb connection
This black, beverage out quick disconnect comes with a barb for attaching to a beverage line, and its high quality construction creates a sturdy seal that won’t leak gas or beer when in use.
The barb measures 1/4 inch, so 3/16 inch beverage tubing is recommend for the perfect fit.
Note: Sometiems ball lock fittings can be difficult to get fully seated on a Cornelius keg. We recommend using a quick spray of sanitizer solution to act as a lubricant and giving it a few twists while applying the ball lock.
Kegland Part Number: KL02950
This John Guest push-to-connect fitting will accept 3/8" OD tubing on one end and thread onto 1/4" female pipe thread on the other. This is a direct replacement part to the push fittings used on BrewBuilt CoolStix™ and MB Reactor Rods. Pairs perfectly with Beer & Gas Tubing QDs (H551 & H550C) for quick disconnect functionality.
Type F Camlock Fitting. Male Camlock with 1/2" Male BSP.
Camlock fittings are the preferred choice for many home and professional brewers alike. They have a higher working pressure and hold a tighter seal than quick disconnect fittings, making them less likely to leak while in use. Locking and unlocking the female pieces may require two hands, but it's a small price to pay for long-lasting reliability.
304 Stainless steel construction. 150 psi working pressure.
Kegland Part Number: KL04510
Leak-free quick connectors are well suited for glycol to cool fermenters.
Fits perfectly in combination with 8.5mm x 14mm EVA tubes both insulated and non-insulated.
Cool your fermenting must or wine using this weldless, easy-to-install, 304 stainless steel cooling plate that can be inserted into the lid of any Variable Volume Fermenter. Cold water or glycol is recirculated through the cooling plates thereby reducing the temperature of your ferment.
This is a stainless steel setup, ensuring no chance of off-flavor in your wine. You drill two 1-1/16" to 1-1/8" holes into the lid. We provide two gaskets and a lock nut to seal on both sides of your lid, securing the plate in place.
Plate measures 24" H x 10.6" W
Inlet and Outlet 1/2" Male BSPP thread
300 mm long tubes
Bulkheads located approx. 175 mm above the plate
0.36 Square meters of cooling surface
Made from 304 stainless steel
Replacement internal seal for Stainless Carbonation and Line Cleaning Ball Lock Quick Disconnects. Only the stainless steel ball lock caps require these seals (KG50 & KG502). They are not needed for the Red & Yellow plastic versions. Comes in pack of 5. KegLand Part Number: KL21272
Pale Ale provides a rich malty flavor with hints of nuts and biscuit
Can be used as 100% of your fermentable sugar in extract brewing
Add for color correction, boost gravity, or improve head retention in all grain brewing
Briess Malt & Ingredients has had a focus on quality and innovation for more than 140 years, with all of their products being made in the U.S.A.
Dried Malt Extract (DME) is the primary sugar source in extract brewing and can be used in partial-mash or all grain brewing to adjust flavor, color and gravity of brews. DME can also be used to increase head retention and body. Many brewers choose nutrient rich DME as the sugar source for making yeast starters as well. Briess dried malt extracts are made from 100% malt and water.
Pale Ale DME: 100% pure malt barley extract made from 100% Pale Ale Malt and water.
Pale Ale is a flavorful and unique DME available from Briess. A rich malty flavor with hints of nuts and biscuit, it can be used in the production of most beer styles, either as a base or to boost gravity. The proprietary malting process creates a malt extract that is not only darker than golden light, but one that is rich and complex.
Typical Analysis:
Color (8° Plato): 6.0 SRM
Fermentability: 75%
Solids: 97%
1.043 PPG
This is our preferred tubing for use in Barrel Topping Systems. Because of its high elasticity this tubing is easy to attach to/detach from barbed fittings without having to cut the tubing to remove it or use hose clamps to install it (in low pressure applications). This feature allows the user to disassemble the tubing set used to deliver the top-up wine for both sanitation as well as cleaning after use. Cleans up easily and does not get stiff at low temperatures. OD is approximately 3/8"
Specs:
Working Pressure - 20 psi
Burst Pressure - 60 psi
Platinum Cured
Manage your fermentation temperature like a stone-cold pro with the BrewBuilt Chilling Pump Kit! This kit can use either ice water or glycol as a chilling solution, which is then circulated through your chilling coil or cooling jacket by the included submersible pump. Available with either 800 or 1300 gallons per hour flow rate and a max lift height of nearly 10 feet, this unassuming pump is powerful enough to circulate your cold solution with ease. And with the Inkbird Dual Stage Temperature Controller running the show, you can feel confident that your fermenters are getting the chilling power they need, when they need it. Submersible Pump If you're searching for an affordable pump to use with your temperature control system, look no further. The BrewBuilt Chilling Pump Kit comes with either a 800 GPH or 1300 GPH submersible pump that can be used with an icebank or glycol chiller. Don't be fooled by the low-profile compact design. With such high flow rates and a max lift height or nearly 10 feet, either of these pumps is sure to keep the solution moving in your chilling system. In general, we recommend the 800 GPH pump for maintaining the temperature of any batch size fermentation that is less than 10 gallons, and the 1300 GPH pump for maintaining any batch size fermentation that is between 10 gallons and 2 bbl. Maximum flow rate: 800 GPH or 1300 GPH Max Lift Height: 9 or 10 ft. High quality motor provides a quiet environment (60W or 100W) Stainless steel impeller shaft for long life span and corrosion resistance 6 ft. long power cord Inkbird Digital Temperature Controller The Inkbird dual stage temperature controller is an easy to use and economical controller that is perfect for home brewing. Inkbird controllers allow you to control both heating and cooling, and set independent differentials for each to protect your heating and cooling devices. The Inkbird ITC-308S controller performs many of the same functions as the Ranco or Johnson but at a more affordable price, making it a great alternative for temperature control. Aside from brewing uses, this is a great dual relay output temperature controller for cooking (use in a smoker or BBQ), home growing (heat mats for seedlings, climate control), or any other DIY project you come up with! Features: Simple plug and play design with user friendly LED interface Dual stage ITC-308 - control both heating and cooling Adjustable Heating/Cooling differential 1000W max power Celsius or Fahrenheit High and low temperature and sensor fault alarms Can control temperatures of -58° F through 210° F (-50° C - 99° C) Body Dimensions: 5.5 in x 2.7 in x 1.3 in Chilling Pump Kit Includes: Submersible Water Pump (PMP601 or PMP602) Inkbird Dual Stage Digital Temperature Controller (FE640) 2x 5 ft. lengths of 3/8 in. Silicone Tubing (H983) 4x Butterfly Hose Clamps Stainless 3/8" Barb x 1/2" MPT Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.
A best seller for a reason! Tons of features at an incredible cost
Crystal Clear super smooth PET makes fermenting and cleaning super easy
3" Butterfly valve at bottom makes removing yeast/trub easy with the 600mL collection jar.
Pressurizable for fermentation and closed transfer to your keg
Includes BlowTie spunding valve kit, red & yellow carbonation caps, and floating dip tube as standard
The FermZilla is the perfect option for brewers that want all the advantages of a conical fermenter without the price tag of a full-blown stainless-steel unit. It allows you to dump trub, harvest yeast, and with the addition of CO2 cylinder and regulator, you can carbonate and serve – all in one vessel! The clear PET tank allows you to visually monitor fermentation activity and is pressure rated to 2.4 Bar (34.8 psi), which means you can ferment under pressure, reducing ester and fusel alcohols in your finished beer. This also gives the ability to perform pressure transfers. If you prefer to move your finished beer to a keg or other vessel, you can do so with little to no oxygen exposure.
The FermZilla Tri-Conical Easy-Grip model comes packed with accessories so you can take full advantage of this pressurizable fermenter on day one. The new stock standard includes Easy-Grip threaded lid ring, BlowTie spunding valve with integrated pressure gauge, ball lock carbonation caps for the lid, floating dip tube kit with weighted filter, volume marker graduation sticker, and adhesive thermometer.
What's Included:
FermZilla 27L Tank with 3" T.C. Bottom Port
Easy-Grip Threaded Lid Ring
Integrated Gauge BlowTie Kit Spunding Valve (0-15 psi)
Silicone Dip Tube Kit with Yellow Weighted Filter and SS Float
(1) Yellow Liquid Carbonation Cap
(1) Red Gas Carbonation Cap
Fermzilla Pressure Lid with Red PRV (35 psi)
3" T.C. Butterfly Valve
600 mL Collection Container with 3" T.C. Connection
Stainless Steel Stand with Swing Handles
3" tri-clamp with gasket
Graduation Sticker
Adhesive Thermometer
Specs:
27 L (7.1 gal) Total Volume
Pressure Rated to 2.4 Bar (34.8 psi)
Height in Stand - 30.2"
Tank Diameter - 13.9"
Diameter in Stand - 15.3"
Lid & Collection Container Ports - 28 mm PCO 1881 threads
Temperature Rating:
When not under pressure, do not expose to liquids above 131°F
When under pressure, do not expose to any temperatures above 95°F*
*Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years.
Please note: when using the FermZilla under pressure, you must perform a water pressure check to ensure your connections are leak proof. To do this, fill your FermZilla up with water, apply at least 15 psi pressure, and check for leaks around all caps and threads.
Pressure Stress
If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple:
Fill the tank to the brim with water
Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher
Pressurize the tank to 4 BAR (58 psi)
Check for leaks, then replace the Red PRV when finished
If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla.
General Care
Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank.
KegLand Part number: KL47296
NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.
FermZilla Tri-Conical 27L & 55L | User Guide
These are designed to be used with the Blichmann BoilerMaker Brew Kettles for use in a mash tun. Will also work great if you're using whole hops in your boil kettle (for pellet hops, we recommend using the Blichmann HopBlocker). A patent pending button louver design is a hybrid of a perforated false bottom and a slotted manifold to give you the best of BOTH designs!
Solenoid valve made from stainless steel. Designed for air/co2.
TC3mm ports in both ends for maximum flexibility.
Coil and plunger Italian-made by ACL.
The valve can easily be disassembled and cleaned.
Coil has DIN 43650 Type B connector (not included).
Specifications:
Ports: TC34mm / TC34mm
Operation: NC (normally closed)
Power supply: DC24V, 6.5W
Orifice: Ø2.0mm
Pressure rating: Max 3 bar / 43 PSI
This unique kettle with four tri-clamp ports was developed for the BrewBuilt electric kettle line as it requires two ports for two electric heating elements. The kettle is offered without fittings so you can rig it up with whatever accessories you see fit.
Welded 1.5" tri-clamp ports for a lifetime of leak-free use
304 stainless steel construction with mirror polish finish
Front and back located handles with silicone grips
Induction burner compatible
Notched lid provides cover while not interfering with immersion chillers, hop bags, or other accessories
The BrewBuilt Pro Brewing Kettle is built for even more versatility than the standard T.C. kettle. A third and fourth tri-clamp port are offset from the front and ready to accept an electric heating element, whirlpool return valve, or any other accessory that you want to incorporate with the kettle. Handles are located at the front and back, rather than either side, saving you space when building out a horizontal system and will keep fittings pointed away from you regardless of which side you pick up the kettle from.
Designed for Brewing. Built to Last.
BrewBuilt brew kettles are made from 304 stainless steel and offer an unparalleled mix of features for the price. At the very top of the list are four welded-in place tri-clamp couplers that offer a lifetime of leak free use. As you can imagine, welding in a coupler costs more than punching a hole and using a gasketed (i.e. weld-less) fitting. Welded fittings offer a permanent connection that to us is worth every penny. The second unique feature that we absolutely love about these brew kettles is the notched lid with silicone plug. This notch allows you so much flexibility; you can use an immersion chiller, one of our Ultimate Sparge Arms for mashing, tie off hop bags, take a temp reading during cooling, or whatever else we all can dream up.
Our T.C. kettles were designed to keep pace with the ever-evolving world of brewing technology. Tri-clamp fittings are standard fare in professional breweries, and they’ve been widely adopted in homebrewing as T.C. fermenters and pumps become more affordable and widely available. Tri-clamp fittings, also known as Tri-clover, allow you to make a sanitary connection that is free of nooks and crannies for contaminants to take hold. They are much easier to break down for cleaning compared to threaded connections, and they don’t require Teflon tape to make a watertight seal. T.C. fittings and accessories also give you the distinct advantage of being able to clean in place (CIP), so you don’t need to break down your entire system after every brew day.
This kettle comes without fittings so you can modify it with whatever tri-clamp accessories best suit your needs.
This Brew Kettle has a lot to offer...
Some other features we dig include the internal volume markers from the bottom to the top - so handy for instant reads. The silicone sleeved handles on the kettle and the lid are a cool feature to protect your hands. The tri-clad bottom with a 4mm core of aluminum sandwiched between two layers of stainless steel offers even heat distribution during the boil and also makes it a perfect choice for anyone wanting to use an induction burner. The bottom coupler is also cool with 1/2" male threads on the outside and 1/2'' female threads on the inside.
Beefy 304 Stainless
These kettles are made from 304 grade stainless. That means you will have less corrosion issues than with a kettle made from lower grade 201 type stainless. We put these kettles through a corrosive salt water test in the MoreBeer! shop and they passed with flying colors. We also made sure the rivets and riveted handles were also made of stainless steel for a long term, trouble free life. The 10 and 15 gallon size are made from 1.0mm thick stainless steel. The 20, 30 and 50 gallon size are made with 1.2mm stainless - that's pretty thick stuff - and you will know it when you pick one up. The included ball valve is a two piece design that allows for easy cleaning (we prefer these over 3 piece for ease of assembly) and is also made from 304 stainless.
Mirror Polish Finish
The mirror polish finish isn’t just for making your Instagram feed pop! This extra slick finish is much easier to clean and sanitize than a standard brushed stainless kettle. Hop trub and other organic solids left behind after a brew day will have a hard time clinging to the interior surface and scrub away with ease.
Size Ratios and Stuff
All the BrewBuilt kettles follow the recent trend to a 1.2:1 ratio where the height is 1.2 times the diameter. This is a proven commercial ratio that has been adopted in homebrewing to achieve a more consistent 10% evaporation rate during the boil. We do like this ratio for boiling. For Mashing we would prefer a little bit shallower but that is a small compromise. Dimensions for a hot-liquor tank, if you are thinking brewing system down the road, are irrelevant as any ratio kettle will do.
Final Words
With welded tri-clamp fittings, mirror polish finish, a bunch of cool features, and a solid, thick 304 stainless steel core this kettle is a pretty amazing value. Remember, if you order from MoreBeer! we ship free anywhere in the continental USA!
Features:
Four welded T.C. couplers for a lifetime of leak free use
Notched lid with silicone plug for flexibility
304 Stainless construction for longevity
1.0mm (10 & 15 gal) or 1.2mm (20, 30 & 50 gal) thick side walls resist denting
4mm Tri-Clad Aluminum bottom sandwiched between two layers of stainless steel for no scorching
Internally etched volume markers from top to bottom for easy reading
Silicone coated handles for heat protection
1.2:1 Ratio is optimal for boiling evaporation rate
Lid is designed to conveniently hang from a handle
Stainless handles with stainless rivets for secure lifting
Kettle ID - 23.62"
Height - 28.3"
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
Sight glass with TC 2" (64mm) connectors
Length: 3.8" (98 mm)
Inside diameter: 1.8" (47.8 mm)
This is the recommended accessories to get you started using the Brewtools pro systems. The package includes an efficient counterflow cooler, an extra 3-way valve to make you able to choose if you return the cooled wort to the tank creating a whirlpool or pump directly to the fermenter. The third 3-way valve makes it possible to clean the system without disconnecting hoses. Our adjustable dip tube is included in this package for optimal control during pumping to fermenter. A third sensor gives you exact measurements of the wort returning from cooling. The necessary fittings and accessories are also included. Fittings for connecting a sparge water heater is not included. Included: 2 pcs 3-way ball valve, TC34mm DN15 1 pcs Dip tube, Adjustable, TC34mm 1 pcs Counterflow Cooler, Pro 3 meter Silicone Tube 16x25mm, clear 3 pcs TC Gasket, 34mm, DN15, 5-pack 2 pcs TC34mm to 12mm hose barb 1 pcs TC34mm to 19mm hose barb, sensor holder 5 pcs TC34mm to 19mm hose barb 1 pcs Temp. Sensor, inline, M10 8 pcs Tri Clamp, 34mm 1 pcs TSP, 100g For User Manuals and support, please follow this link to Brewtools Docs.
This Duotight joiner fitting is compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL02370
We recently discovered this premium breathable silicone barrel bung and were immediately impressed with its robust design and features. To start with, the built in tabs really help make bung removal effortless. But where the bung really shines is in its two-piece design. When set to the open position, the bung acts as an airlock and allows the release of CO2 while maintaining a seal against oxygen coming in. This makes the bung ideal for alcoholic or malolactic fermentation in barrels or tanks. When fermentation is over and you no longer want the bung to "breathe" out, you just push the center cap into the bung to create a firm seal and the FE497 becomes a solid stopper!
Fits most 30 and 60 gallon barrels as well as the hole in the lid of most Variable Volume tanks!
tapers from 1 7/8" to 2 1/4" diameter
Universal stoppers have a longer taper to help produce a better fit and a snug seal, and a lip which prevents them from falling into your container. Available with a 3/8 inch hole for an airlock, or solid with no hole.
#11-11.5 (large) size is recommended for full size barrels and 14 gallon demijohns.
This Duotight fitting with 1/2" male thread is perfect for attaching to the Copper Counterflow Chiller (WC130) and using with 1/2" female threaded Camlock and QD fittings. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL06927
Stainless steel shank comes with a back nut, plastic collar, and a 3/16" tailpiece with hex nut and gasket. If desired, the barb can be removed and swapped for a different size or replaced with a Duotight x Beer Thread Adapter. This size of beer shank is a popular choice for building your own custom draft system. Typically installed in the door of a refrigerator or the wooden collar of a converted chest freezer. The shank’s listed size refers to the total length of threaded pipe. Approximately 1-1/8” are needed to account for the thickness of the finishing collar on the front and the space for the locknut on the back. Please take this into account when sizing the shank for your project. Installation Note: On a fridge there are generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 4-1/4" - Total Length (Tip to Tip) 3-1/8" - Shank Length (Without Nut & Nipple) 2-1/4" - Thread Length 1-3/4" - Pass Through Length 3/16" Nipple
New Corny Keg ready to use right out of the box
New Kegs are trouble-free for years
Rubber top and bottoms protect floors from dings
Lid includes a tab wth hole welded in so you can hang anything from lid (dry hop our favorite)
304 Stainless Steel and great welds, this will last a tifetime
Features Low2 Keg Lid O-ring which offers a 96% reduction in oxygen ingress compared to silicone.
Ditch the bottles and start kegging today! Save time, reduce the risk of infection and get all those bottles out of the kitchen for good!
Brand new 2.5 gallon Kegland kegs offer convenience, security and insurance when compared to used or reconditioned kegs. There's no need to replace gaskets or other parts, no need to trust that someone else did a good job with reconditioning, and no possibility of residual flavor or aromas getting into your beer!
These Premium 2.5 gal kegs have a lid with an internal tab/hook under the lid designed specifically for attaching dry hopping bags.
Features:
130 PSI Operating Pressure
2.5 Gallon (9.5 L) Capacity
Dry Hop Tab Welded into Lid
Cold Activated Keg Filler Sticker
Beverage Tag Sticker
304 Stainless Steel
Dimensions:
Height: 14.5 in.
Diameter: 8.375 in.
Kegland Part Number: KL02882
The BrewBuilt SlingBlade is an innovative electric heating element designed to promote a rolling boil and even heat distribution. Shaped for Performance and Convenience The SlingBlade's unique crescent-shaped design positions all of the heating power on one side of the kettle, sending thermal energy upward to the surface that then cascades downward on the opposite side of the kettle. This movement creates a dynamic turbulence that evenly distributes heat while creating a vigorous, rolling boil. Other heating elements stick right out into the middle of the kettle or use a full circle design that rings the kettle wall. This can cause an obstruction for immersion chillers or make it difficult to stir without banging into the element. The SlingBlade was designed to avoid these issues. By remaining on one side of the kettle, the element will be out of the way of your immersion chiller, and since the element follows the curvature of the kettle wall, it won't interfere with the flow of wort during whirlpool. Ultra-Low Watt Density An electric element transfers power to your wort by applying heat, but if this heat is too concentrated you will get local heating that is hotter than 212°F. This catalyzes Maillard Reactions, which can lead to darker beer than intended and produce unwanted caramelization. Think of these reactions like roasting a marshmallow. First it gets a light brown, we call this Maillard reactions, a little hotter and it gets a dark brown, we call this caramelization, then it turns black and we call this pyrolysis (burnt or scorched). While all kettles undergo these reactions, an electric element can concentrate more heat into a small area, which can quickly scorch your wort. Our experience is that at 90-watts per square inch recipes need to be modified to account for the element and light beers never come out quite right. The SlingBlade element was designed at 50-watts per square inch to reduce the chance of scorching while still providing a vigorous boil. For even lower watt density, consider the Boil Vigor Controller. Tri-Clamp Connection The SlingBlade installs quickly and easily on any kettle with a T.C. ferrule thanks to the curved, non-circular design. This also makes it a breeze to remove the element for cleaning between uses. The SlingBlade heating elements were designed to fit perfectly with BrewBuilt brewing kettles, but you may find them suitable for other kettles as well. They should be used with T.C. ferrules no longer than 1" in length. For dimensions and recommended minimum kettle diameter, please see the chart below. Features: Made from Incoloy alloy with proprietary coating for long life 1.5" Tri-Clamp connection Unique offset design promotes rolling boil Ultra-Low Watt Density eliminates scorching UL Certified components Specs: 240 Volt L6-30 plug 20 Amp breaker required for 10 & 15 gal element 30 Amp breaker required for 22 & 31 gal element 50-gallon kettle requires 2 x BE538 and 2 x 30 amp circuits SKU Kettle Vol. Wattage Length Radius Min. Kettle Ø BE535 10 gal 3750 13.25" 6.3" 13.78" BE536 15 gal 4500 16.75" 7.3" 15.75" BE537 22 gal 5000 17.25" 8.3" 17.72" BE538 31 gal 5750 19.5" 9.3" 19.69" Please note: Length is measured from the tip of the heating element to the T.C. connection. Radius is measured from the middle of the T.C. connection to the outermost edge of the element's curve. ***In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.*** Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.
