KegLand is a high quality homebrewing equipment brand based out of Australia. We offer a wide variety of their products, from BrewZilla all-in-one system and DigiBoil eletric kettles, to pumps and grain mills. KegLand beer products are an incredible value, as they combine quality craftsmanship with low prices!
Magnetic drive enables you to slow down the flow without damaging the pump—just add a ball valve to the outlet!
T.C. connection allows the pump head to be oriented at any angle in a full 360-degrees
Pull ring PRV at the pump outlet makes it easy to purge air and prime the pump before each use
Inline flow path for smooth integration into your brewery while keeping your tubing lines tidy
Stainless steel head with 1/2" threaded ports to attach your preferred fittings—tri-clamp, quick disconnect, camlock, and More!
The best-selling MKII Magnetic Drive Pump now available with a major upgrade! This unit comes standard with an inline stainless steel pump head that installs on the pump body with a 3" tri-clamp. Compared to the standard "center inlet" pump head, the "inline" flow path can make it much easier to integrate into your brewery and keep your brewing hoses tidy. At the outlet of the pump, there is a very handy pull ring PRV that allows you to bleed liquor or wort from the pump head to release trapped air and prime the pump. And with the 3" T.C. connection, not only do you have a full 360-degrees to orient the pump head any which way, cleaning the pump after use could not be easier—just pop off the tri-clamp, wash out the pump head, and clamp back on.
The MKII is a perfect pump for your system and comes highly recommended for brewers stepping up to all-grain brewing. Rather than schlepping heavy kettles filled with hot liquor or wort around your brewery, or awkwardly stacking them into a 3-tier gravity setup, allow this handy pump to move liquid from vessel to vessel while everything remains in place. The magnetic drive allows you to slow down the flow without damaging the pump. This can be done by attaching a ball valve to the outlet side of the pump, and then you simply open or close the valve to control the flow rate. The pump itself is not self-priming, but priming is super easy thanks to the pull ring PRV which will help ensure the pump head is full of liquid and trapped air is released before powering it on.
Tri-Clamp Pump Head
The T.C. pump head can be removed quickly and easily using the 3" tri-clamp. This means no drivers or power drills are needed to back out the six Phillips head screws that mount the pump head on the standard version of the MKII. Whip the head off in a flash to clear out spent grain, hop material, or clear a blockage. Attaching the pump head with a tri-clamp also allows the head to be rotated at any angle in a full 360-degrees. This makes it easy to configure the plumbing to your unique brewery setup.
Inline Design
An "inline" pump head simply means the input and output are on a straight horizontal line with one another which can make it easier to integrate into your brewery setup. If you're using a 3-vessel horizontal system, the inline pump head will make it easier to keep your hoses neat and tidy compared to pumps heads with a center inlet.
PRV Purge Valve
The corny keg style PRV will make priming the pump a breeze. Simply let bleed the pump head to purge air out before turning the pump on and you'll avoid any cavitation issues. The PRV also acts as a safety so you do not over pressurize your pump head or brewery system.
304 Stainless Steel
The entire pump head is made from 304 grade stainless steel so it's highly resistant to chemicals, heat, and physical abuse. The 1/2" BSP threaded ports can be used to attach barbs, quick disconnects, camlocks, tri-clamp adapters, or any other 1/2" fittings you prefer.
Features:
110V / 60hz
Max Head: 11.15 ft. (3.4 m)
Max Flow: 5 Gal/min (19L/min)
Max Temperature: 248°F (120°C)
360° rotatable stainless steel pump head
1/2" BSP ports
Water resistant casing (not waterproof)
KegLand Part Number: KL27236
If you're brewing on a budget and want the most affordable pump possible, check out the standard model MKII pump. This has been our best-selling pump for years and you can always upgrade it down the road with the standard stainless center inlet head or inline stainless tri-clamp head.
Unique Core Puncturing / Actuator results in zero gas lost from screwing in CO2 cartridges
Interchangeable ball lock disconnect orientations. 45° for plastic QDs or 90° for stainless QDs
6.5mm Duotight compatible hose barb
Swappable mini pressure gauge remains well protected within solid cast brass regulator body
Corny-style 65psi Green PRV for added safety and manual depressurizing
Switch from 16g to 74g CO2 cartridges with an adapter fitting
The new Core 360 Mini CO2 Regulator from KegLand represents a huge jump forward in the mini regulator market. After much feedback on how to make mini regulators more compact, sturdy and efficient, the brilliant engineers at KegLand have come up with this mini-beast.
The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge.
Heavy Duty Construction
Starting with the body of the regulator, this unit is made from chrome-plated solid cast brass which means it will stand up to quite a bit of abuse. Unlike most mini regulators, the pressure gauge on the Core 360 is safely recessed in the regulator body, so if you ever drop it there is little chance that you'll damage the gauge. What's more, the gauge is removable, so you can swap it out with another mini gauge with a pressure range that better suits your application.
Unique Cartridge Connection
What really sets this unit apart from other mini regulators is the way in which you insert a CO2 cartridge. A common complaint with these types of regulators is that you can lose a lot of gas from the cartridge just from threading it into the regulator. There's that brief period where the cartridge has been punctured but you haven't fully threaded it into the regulator to form a seal. If you're not quick enough, this can result in a significant amount of lost gas. The Core 360 has a unique design feature where inserting the cartridge is a 2-step process. First you fully thread in the cartridge so it forms a seal before it's opened, and then you screw down the actuator pin to release gas into the regulator. Simple and effective.
Furthermore, the Core 360 Mini Regulator is designed to be compatible with both 16g and 74g cartridges. Out of the box it will be ready to accept 16-gram 3/8"-24 UNF threaded cartridges. But with a simple adapter you can switch to 74-gram 5/8"-18 UNF threaded cartridges.
Interchangeable Gas Outlet
Another feature we haven't seen before on a mini regulator is the interchangeable gas outlet. You can use the swivel nut connection to directly attach the regulator to a flare ball lock disconnect, or you can swap to the 6.5mm Duotight-compatible barb and connect draft tubing. This is a great option if you want to dispense a commercial keg without the need of a ball lock to sanke coupler adapter.
The regulator also has two outlet options at either a 45° or 90° angle which makes this the ideal mini regulator regardless of whether you use plastic or stainless steel ball lock disconnects.
SodaStream Compatible
If you remove the 16g cartridge bushing, you'll find TR21-4 female threads for use with SodaStream gas cylinders. These can be a great option for mobile dispensing as they provide much more gas than a CO2 cartridge and are more easily transported than a full CO2 tank.
Includes:
KegLand Core 360 Mini Regulator
6.5mm Duotight-compatible hose barb
Female Flare Fitting for MFL Disconnects
Port end cap
65psi Green PRV
SodaStream to 16g thread bushing
KegLand Part Number: KL20404
Warning: Do not overtighten onto your cylinder. It is recommended that you use a spanner to hold the neck of your SodaStream cylinder while attaching and detaching the Mini 360 Core Actuator Regulator.
Mini 360 Core Actuator Regulator | User Guide
Crafted from heavy-duty, impact-resistant material, Big Jugs endure drops and freezer conditions without cracking or breaking
Made from BPA-free materials with clear, dual-scale markings for accurate measurements up to 125 fl oz or 3500 mL
Features a wide-mouth opening for easy filling and cleaning, an integrated drip-free spout, and a comfortable ergonomic handle for versatile use
Tired of flimsy measuring tools that crack and break? Big Jugs are your robust solution. Perfect for dissolving ingredients like DME or dextrose for bottle conditioning, or for safely mixing cleaning chemicals, these jugs are heavy-duty and impact-resistant, designed to endure drops and even freezer conditions without breaking.
Big Jugs are made from BPA-free materials, ensuring no harmful chemicals leach into your food or boiling liquids. Achieve precise results with the clear, easy-to-read measurement markings with dual scales that measure up to 125 fl oz or 3500 mL.
The smart design of Big Jugs prioritizes your convenience. A wide-mouth opening allows for effortless filling and cleaning, while the integrated spout guarantees smooth, drip-free pouring. With a generous capacity and a comfortable, ergonomic handle, these jugs are as versatile as they are durable, ready for any task in your beverage crafting process.
Key Advantages:
Extreme Durability: Withstands impact and harsh conditions.
Food-Safe: Made with BPA-free materials.
Accurate & Easy: Clear markings for precise measurements.
Convenient Features: Wide opening, drip-free spout, ergonomic handle.
Multi-Use Functionality: Ideal for a broad range of applications.
KegLand Part Number: KL45124
If you are looking to measure the temperature of your fermentation directly from the wort, simply install this extension probe into your RAPT Fermentation Chamber. The RAPT is designed to heat and cool your entire fermenter. This is the ideal scenario as the whole fermentation vessel is placed in a temperature-controlled environment which gives you the most even temperature and most precise control of your fermenter. This 2m (6.5') Extension Probe allows you to easily measure and control the temperature from right inside your fermenter, allowing for super precise readings throughout the fermentation.
This is a simple plug-and-play fitting for your RAPT. For the highest accuracy, run through a 2-point calibration in the settings menu.
The probe diameter is 4 mm (0.15").
KegLand Part Number: KL22460
Seal your bottles like a pro — fast, flawless, and built to last.
The Gen 2.0 Super Automatic Lever Bench Capper delivers professional-grade results with one effortless motion. Built from durable steel and engineered for smooth, repeatable performance, it’s the ultimate upgrade from hand cappers.
Key Features:
One-Handed Operation: Drop the bottle, pull the lever, and you’re done. A magnetic bell holds each crown perfectly in place for a clean, consistent seal.
Adjustable Height: Easily fits different bottle sizes — from 12 oz to larger formats — with quick, tool-free adjustment.
Rock-Solid Build: All-metal construction and a rubber-grip base keep every seal steady and precise.
Extended Base for Extra Leverage: The long base design provides added stability and leverage, preventing the capper from tipping forward during operation — even with taller bottles.
Precision & Speed: Cap hundreds of bottles quickly with uniform, leak-proof results.
Bench-Mount Ready: Pre-drilled holes make it easy to bolt down for true production-line efficiency.
Why Brewers Love It
Reliable, ergonomic, and built for volume — the Gen 2.0 makes bottling faster, easier, and more professional than ever.
KegLand Part Number: KL05340
Replaces the circular top inlet of the MaltZilla to allow for easier adding of grains. This product is still in development. Details will be added as they become available.
Hopper only. MaltZilla and Base Board sold separately.
For use with the 35L BrewZilla Boiler Extension Kit. It does not come with an extra Wire Malt Pipe Support Ring. If you're using the extended malt pipe with the 35L DigiBoil, you will need to purchase the ring separately. If you're using the malt pipe with the 35L BrewZilla you can either move your ring up to the boiler extension, or buy an additional ring so you can remove the malt pipe in two steps. You will also need the Ricirculation Arm Extension to continue using the BrewZilla's recirculation arm. Compatible with Gen 3 / Gen 4 BrewZillas. KegLand Part Number: KL26468
Digital temperature control
Triple heating element control (2000w, 1000w and 500w) 17 gallon total capacity 304 stainless steel construction
220V / 20A power This is a versatile electric kettle that can be used as a standalone unit or integrated into your current brew system to serve a variety of functions. Easily brew 10-gallon extract batches. Use it to preheat your strike water or sparge water to a precise temperature. Pair it with a pump and heat exchanger to use it for HERMS brewing. Or slap on a still top lid and condenser for distilling! With so many ways to use the DigiBoil, and an affordable price tag to boot, it's hard not to get excited about this electric kettle! The Gen 2 DigiBoil features an upgraded glass lid, allowing you to monitor your heated or boiling liquid. Interested in using the DigiBoil for all-grain brewing? With the Mash Upgrade Kit, you can easily convert the DigiBoil into an electric mash tun! This DigiBoil model has three built-in heating elements that run off a 220V plug. The elements are 2000w, 1000w and 500w for a combined 3500 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage all three elements to quickly go from steeping temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s). Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach 1/2" FPT fittings if desired. More! Features: NEMA 6-30R plug (4.5 ft. cord) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Glass lid Temperature reads in °F or °C With elements turned off, hold both the +/- buttons to switch between °F or °C Compatible with reflux and pot still (DS130& DS120)*
External Dimensions: 29" H x 19.5" W (including handles) Internal Dimensions: 20.25" H x 15.75" W ETL Listed *Distilling: to use the DigiBoil with a distilling condenser, you will need to purchase the still top lid (DS127). Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States. It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. MoreBeer! is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA). Kegland Part number: KL07313 NOTE: Due to the size of this item, it is not eligible for international shipping.
Heavy-duty stainless steel lid can be used with a still top or steam condenser
Sight glass disc allows you to watch your boil without having to remove your still or condenser
Easily remove the disc during the hot break or to add hops or other boil additions
Molded grips for easier handling with the lid is still hot
Compatible with 65L BrewZillas and DigiBoils
If you're using an AlcoEngine Still Top or Steam Condenser set with your BrewZilla or DigiBoil, this heavy-duty stainless lid with sight glass is virtually a must-have. Whether distilling or brewing, keeping an eye on your boil will help you stop foaming or boil over issues before they happen. With the standard distillation lid, checking on your wash or wort means removing or tipping the apparatus over to get a peek inside the boiler, which can be a cumbersome (if not dangerous) part of your process. The PPSU sight glass disc can also be easily removed to add hops or other boil additions through the large 3" T.C. ferrule. (Use gloves, it will be hot!)
The 65L lid is designed to be extremely sturdy when using heavier stills and is made with a 4" T.C. ferrule top port. To pair the lid with an AlcoEngine Still Top or the BrewZilla Steam Condenser Set, you can use a 2" x 4" T.C. reducer. (The AlcoEngine Still Tops will also need this single sided bead seal for a secure tri-clamp connection.)
The sight glass disc is made from a special PPSU plastic—an excellent choice for components that are exposed to high temperatures (up to 392°F / 200°C) and corrosive media due to its exceptional chemical resistance, as well as being extremely impact resistant. KegLand decided to use this type of plastic because it also has superior thermal and mechanical properties with the added benefit of being transparent. Intricate parts can be injection molded that would have been near impossible to do with stainless steel or lab-grade glass.
Specs:
4" T.C. top ferrule port
3" T.C. sight glass ferrule
Lid handles with molded grips
Thicker silicone lid gasket for a tighter seal
Includes:
3" PPSU sight glass disc
3" tri-clamp
3" silicone tri-clamp gasket
Silicone lid gasket
KegLand Part Number: KL25829
Replacement PET Tank for the 27L Tri-Conical FermZilla with tri-clamp bottom port. Perhaps your wort was too hot when you transferred from the kettle, or while cleaning you dropped the FermZilla against something sharp that punched a hole, or maybe it's just time to replace the tank after acquiring too many scratches from normal wear-and-tear. Whatever the reason, no need to go buy a whole new FermZilla! Just pick up one of these fresh replacement tanks and your conical fermenter will be good as new! Pressure Stress If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple: Fill the tank to the brim with water Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher Pressurize the tank to 4 BAR (58 psi) Check for leaks, then replace the Red PRV when finished If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla. General Care Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank. KegLand Part Number: KL28240 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.
These plastic quick disconnects are intended for use with the QD inlet and outlets found on the Copper Pot Still and Copper Reflux Still (DS120 & DS130).
Use with 7/16" ID Vinyl Tubing (R322) or 1/2" ID Vinyl Tubing (R330).
Maximize the purity of your distillate with high density spiral prismatic packing Prismatic spiral shape designed to maximize surface area One 500g bag is suitable for filling one 10" long 2" tri-clamp extension tube Take you distillation to the next level with super high density spiral prismatic packing. The packing maximizes the purity of the collected distillate from your reflux still, ensuring the best possible product is collected. The prismatic spiral shape is designed to maximize its surface area helping to separate out fractions in your reflux, resulting in a highly pure and neutral end product. It is not recommended for use with pot stills when producing flavored spirits. Standard spiral prismatic packing is recommended for home-sized columns like the AlcoEngine series. Large size packing is recommended for 4" diameter or larger columns. Note: We recommend soaking and washing the SPP before its first use with a 50:50 mix of vinegar or citric acid and warm to hot water to remove all manufacturing oils. Sizing: The SPP is approximately 3.35mm x 3.45mm. Suitable to fill a 10” x 2” T.C. Extension Tube. One 500g bag of SPP is enough to fill approximately 500 mL (16.9 oz) of volume. The HETP (Height Equivalent to a Theoretical Plate) for this packing is approximately 30mm. That is roughly 33 theoretical plates per meter. KegLand Part Number: KL25706
Replacement handles for all BrewZilla Gen 4 glass lids. Also compatible with Gen 3.1.1 BrewZilla lids if you want to upgrade.
Sold as a set of 2.
KegLand Part Number: KL29537
The Gen 2 DigiBoil features two distinct updates that are not currently pictured in the primary images. The stainless steel lid has been upgraded to a glass lid, allowing you to observe and monitor boil activity. The rubber feet have been replaced with a plastic base that provides improved stability and slightly raises the unit for better ground clearance. Updated images coming soon. The most affordable all-in-one automated all-grain brewing system! Mash grains and boil wort in a single vessel External pump kit for recirculating mash will improve efficiency, consistency, and clarity DigiBoil electric kettle automatically maintains mash temperatures with the digital controller Dual heating elements combine for 1500W of power The DigiMash system represents the best value in electric all-grain brewing you'll find. With a 9-gallon DigiBoil electric kettle and the DigiMash stainless steel mashing accessory pack included, this is by far the most affordable way to get into electric all-grain brewing. It may not have all the bells and whistles of the BrewZilla, but it does have everything you need to mash and boil all in one unit. With the Recirculation Pump Kit, you can recirculate sweet wort during the mash to improve starch conversion, maintain a consistent temperature throughout the mash, and improve the clarity. The pump can also be used to move water around your brewery if you use a secondary vessel to hold sparge water, or to transfer the wort from your kettle to your fermenter. With the optional Whirlpool Arm, you can also swap out the Recirculation Arm and use your pump kit to whirlpool after the boil. If you're deciding between the DigiMash and the BrewZilla, there are a couple of key differences worth noting. One of our favorite features of the BrewZilla is the programmable mash steps and delayed start, which the DigiMash does not have. You can still step mash by simply raising the temperature manually on the controller, but the automatic steps are a convenient feature if you want to set it and forget it. One advantage that this setup has over the BrewZilla is that the pump is external. This makes cleaning and fixing pump issues much easier, as you can quickly take apart the pump head to clean and clear out residual gunk at the end of each brew day. This model comes with the 35L DigiBoil, which has two built-in heating elements that run off a 110V plug. One element is 1000w and the other is 500w for a combined 1500 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage both elements to quickly go from mash temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s). DigiBoil Features: 304 stainless steel construction 9-gallon total capacity Digital temperature control 110V / 15A power and plug (5 ft. cord) Dual heating element control (1000w and 500w) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Stainless lid Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Recommended max. grain bill - 18 lbs Recommended min. grain bill - 8 lbs External Dimensions: 29" H x 15" W (including handles) Internal Dimensions: 19.5" H x 11.75" W DigiMash Stainless Steel Accessory Pack Includes: False bottom Malt pipe Wire support Malt pipe handle Malt pipe bottom screen Recirculation Pump Kit Includes: High temp magnetic drive pump Recirculation arm with male camlock Female camlock with barb fitting 1/2" FPT x 1/2" barb fitting 1/2" MPT x 5/8" barb fitting 1/2" ball valve 5 ft. length of silicone tubing 4 x hose clamps Plumber's tape
Perfect for home use with compact keg setups or on the go for mobile dispensing
Compatible with both 16g and 74g CO2 cartridges
Features a 6.35mm Duotight-compatible barb for fast, hassle-free keg attachments
The Duotight Mini CO2 Regulator is a simple, affordable choice for mini kegs and Oxebar keg setups. This compact regulator is designed to work with both 16g and 74g CO2 cartridges, making it ideal for home use or when you're on the go.
With the 6.35mm Duotight-compatible barb you can connect just about anything within a matter of seconds. Simply pair it with the 6.35mm Duotight Ball Lock QD for a quick and hassle-free connection to your kegs. Or, with the Duotight Reducer, you can adapt the regulator for use with the most common and widely used 8mm Duotight accessories.
For additional protection against liquid backflow, you can integrate a check valve along with some hosing to safeguard your regulator. Please note if liquid enters the regulator, it's no longer functional. Be extremely careful with overfilling your kegs or tipping them over when the gas has run out.
The regulator is capped at 30 psi to ensure you do not accidentally over carbonate or exceed your keg's pressure rating. The gauge reads up to 60 psi to account for potential heat expansion so that it does not break the gauge.
Suitable Gas Cartridges:
16g Cartridge 6-pack (KEG993)
74g Cartridge (KEG969)
KegLand Part Number: KL4200
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
This stainless steel CIP spray ball kit is perfect for homebrew conical fermenters as many popular units out there feature a 4" T.C. top port or clamp-on lid with 4" T.C. ferrule. Tri-clamp gasket not included.
Kit Includes:
4" T.C. Cap with 1.5" T.C. x 1" BSP Male Thread connections
1" BSP x CIP Spray Head
Requires pump with 12 GPM flow rate
KegLand Part Number: KL22989
Teflon gasket with 304 stainless mesh screen for 1.5" tri-clamp connections. Can be used as a filter screen to trap large particulates passing through T.C. fittings. Often used for distillation to retain activated carbon for filtering neutral spirits or used in pot distillation to retain botanicals in the vapor stream. This screen can also be used with the 1.5" Hop Bong as an inline filter. The screen has a mesh size of 7 which will block particles larger than 2.83mm or 2830 microns. This slightly larger mesh size makes this screen ideal for use in a distillation basket. KegLand Part Number: KL28516
This Self Closing Spring is made of 304 stainless steel and designed specifically to ensure your NukaTap stays closed when it should. Simply let go of the tap handle and the tap will snap shut and prevent accidentally leaving the faucet open and wasting pressure beer. This handy device suits all NukaTap Mini tap and shank combinations as well as the G2 NukaTap Flow Control faucet (D15841). NukaTap Mini sold separately here. KegLand Part Number: KL32216
How frustrating is it when hops cause blockage in your poppet, tap, ball valves and practically everywhere else? This really handy little filter can be used on with the Torpedo Keg Buoy or the floating dip tubes included with the Kegmenter and FermZilla Pressure Kit to prevent hops or other solids from getting sucked into the dip tube itself. The 304 stainless 80 mesh is fine enough to filter out hops and many other solids but not so fine that it gets blocked up easily. If you have a FermZilla or stainless Kegmenter this add is a must. Made from HDPE and 304 Grade stainless steel, this product can be boiled or sanitized in the full range of cleaners that we sell. The plastic HDPE is over molded onto the stainless mesh to make a seamless finish. The end cap can easily pop off for cleaning. Kegland Part Number: KL16957
Heat resistant to 932°F
Perfect for use with the HIZO G14 Pizza Oven, baking, hot pots, grilling, barbecuing, and woodstoves
High-quality aramid fibers for insulation and cotton and polyester lining
Machine washable
The KegLand Heat Resistant Gloves are as impressive as they are functional with the ability to handle contact with temperatures of up to 932°F. This means that it is perfect for use with oven baking, hot pots, grilling, barbecuing, and woodstoves.
Fashioned with high-quality aramid fibers which work to insulate and protect hands from burning temperatures, these gloves have a comfortable cotton and polyester lining which allows for breathability to resist sweating and a gauntlet-length style of design to protect wrists and forearm from scorching heat as well. These gloves are thick to provide excellent thermal protection and durability, but they are lightweight for extended use without fatigue.
Sizing: Medium (fits most, but may be too small for very large hands).
With heat resistance up to 932°F, these gloves are perfect for:
Oven baking, hot pots, grilling, barbecuing, and woodstoves
Adjusting logs in the fireplace
Touching scorching hot utensils or food while boiling or frying
Features:
High-quality aramid fibers for insulation and cotton and polyester lining
Designed for mobility and flexibility in mind
Food-grade silicone layer
Machine-washable (hang dry)
KegLand Part Number: KL32292
The DigiBoil is a versatile electric kettle that can be used as a standalone unit or integrated into your current brew system to serve a variety of functions. Easily brew 5-gallon extract batches. Use it to preheat your strike water or sparge water to a precise temperature. Pair it with a pump and heat exchanger to use it for HERMS brewing. Or slap on a still top lid and condenser for distilling! With so many ways to use the DigiBoil, and an affordable price tag to boot, it's hard not to get excited about this electric kettle!
The Gen 2 DigiBoil features an upgraded glass lid, allowing you to monitor your heated or boiling liquid.
Interested in using the DigiBoil for all-grain brewing? With the Mash Upgrade Kit, you can easily convert the DigiBoil into an electric mash tun!
This DigiBoil model has two built-in heating elements that run off a 220V plug. One element is 1900w and the other is 500w for a combined 2400 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage both elements to quickly go from steeping temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s).
If you have access to 220V power, this is definitely the unit we recommend. Although 110V power is enough to get up to boil, 220V will get you there faster and provide a much more vigorous boil.
Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach 1/2" FPT fittings if desired.
Features:
304 stainless steel construction
9 gallon total capacity
Digital temperature control
220V / 15A power
NEMA 6-30 plug (5 ft. cord)
Dual heating element control (1900w and 500w)
Heating elements are concealed for easy cleaning
304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2")
Stamped-in volume markers (gallons & liters)
Glass lid
Temperature reads in °F or °C
With elements turned off, hold both +/- buttons to switch between °F or °C
Compatible with reflux and pot still (DS130& DS120)*
External Dimensions: 29" H x 15" W (including handles)
Internal Dimensions: 19.5" H x 11.75" W
ETL Listed
*Distilling: to use the DigiBoil with a distilling condenser, you will need to purchase the Distillation Lid.
Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States. It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA).
KegLand Part Number: KL07252
High temp silicone grip provides a cool touch even with hot liquids!
Ribbed grips allow quick comfortable tool-free operation
Fits all male 1/2" NPT and BSP fittings
1/2" stainless steel barb tail
The KegLand Stainless Steel Quick Connectors come with a heavy-duty silicone grip guard allowing comfortable and quick tool-free operation.
These are ideal for the BrewZilla & DigiBoil ball valves, 25-Watt MKII Magnetic Drive Pump, or any 1/2" NPT or BSP connection.
Specs:
Stainless steel and silicone construction
Silicone O-ring seal is retained for perfect positioning but is easily cleaned or replaced
1/2" (13mm) stainless steel barb tail with 3/8" (10mm) ID bore
KegLand Part Number: KL31639
Wall mount 2" OD piping Perfect for hard piped brewing systems Highly recommended for the bulky KegLand Activated Carbon Filter kits Pipe hanger clamps are quite useful if you want to mount 2" tubing to your wall, whether it be tri-clamp extension tubes for hard piped brewing systems or bulky accessories like activated carbon filters for distilled spirits. Made from 304 stainless steel. DN50 suitable for 2" to 2.25" OD tubing. We recommend purchasing at least two hanger clamps for wall mounting. KegLand Part Number: KL13116
Clean multiple beverage draft lines in a single loop using this Ball Lock Keg Jumper Post. Makes cleaning your kegerator or keezer a breeze without the need to remove your quick disconnects. This double ended keg post does not have a spring & poppet. It just has a piece of bar that activates the ball lock disconnect wide open.
Please note it is a single piece that cannot be undone from the middle.
KegLand Part Number: KL20152
Ready to dive into distilling, but unsure how to piece together your home still? Check out these complete systems that will set you on the path to producing high quality spirits. This kit comes with the 35L DigiBoil Electric Kettle and the Copper Reflux Still Condenser.
The Copper Reflux Still Condenser is designed to create high percentage pure neutral spirit. It features a flow management device, which makes it extremely easy to use. No need to worry about fine tuning the water flow speed. As long as your providing enough coolant or cold water running through the condenser, the flow rate doesn't matter. The purity of the spirit can be controlled by two included flow control inserts. These brass inserts come with a 1.0mm hole and 0.6mm hole. As the hole gets smaller, the rate at which the spirit exits the condenser will decrease, thus increasing your reflux ratio and the purity of your spirit.
If you want to make whiskeys and gins we recommend checking out the pot still kit!
Made from solid copper. When your hot spirit comes into contact with the copper, the copper acts like a catalytic converter to drive sulfur out of the spirit. This leads to less off-flavors and higher quality spirit.
Kit Includes:
35L DigiBoil Gen 2 (110V or 220V)
Copper Reflux Still Condenser w/ Barb Connections
13 mm Inlet/Outlet Barbs (0.51 in.)
Distillation Lid & Gasket
Set of Adjustable Lid Clamps
Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States. It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA).
Replacement Polycarbonate Cup if you happened to damage or lose the reservoir for the 1.5" Tri-Clover Spunding Valve during routine cleaning and replacement of sanitizer solution post-fermentation. KegLand Part Number: KL27472
This is a replacement silicone elbow bend for 35L or 65L BrewZillas. Compatible with Gen 3 and Gen 4. This part joins the pump to the inlet on the base of the BrewZilla then to the outlet of the pump to the recirculation arm on the side of the BrewZilla.
Made from food grade silicone. Temperature resistant to 356°F (180°C).
KegLand Part Number: KL06293
Universal Filling: Ergonomic trigger design allows you to fill bottles of any shape or depth without extra attachments.
Oxidation Protection: Integrated CO2 purge clears oxygen before filling to maximize shelf life and freshness.
Instant Setup: Tool-free Duotight push-connect fittings provide a fast, leak-free assembly and teardown.
Pure Flavor Path: High-grade stainless steel construction ensures zero off-flavors and effortless cleaning.
Take Your Draft Anywhere: The Duotight Handheld Bottle Filler
Stop leaving your best brews behind. Whether you’re heading to a tailgate, a beach bonfire, or a bottle share, the Duotight Handheld Bottle Filler is the ultimate tool for transitioning your kegged beer into portable bottles without sacrificing quality.
Why Choose the Handheld Filler?
Precision-engineered for the modern homebrewer, this unit ensures that every drop of beer only touches high-grade stainless steel. This keeps your flavors pure and your cleaning process simple. To ensure your beer stays as fresh in the bottle as it was in the keg, the integrated CO2 purge clears out oxygen before you fill, significantly extending the shelf life of your bottled creations.
Faster Setup with Duotight Technology
Gone are the days of wrestling with barb fittings and hose clamps. This updated model comes standard with Duotight push-connect fittings, making assembly and teardown incredibly fast and leak-free. The system is designed for brewers who value their time as much as their beer.
Versatile & Ergonomic Design
The filler's intuitive trigger system and ergonomic handle make high-volume bottling fatigue-free. Unlike counter-pressure fillers that require a specific stopper seal, this gun allows you to fill bottles of any depth or shape without needing extra stems or messy hose extensions.
Key Features:
Oxidation Control: Built-in CO2 jacketing tube purges bottles for professional-level shelf stability.
Universal Compatibility: Fill growlers, bombers, or standard 12oz bottles with ease.
Tool-Free Assembly: Duotight fittings provide a secure, airtight seal that snaps together in seconds.
All-Stainless Path: Ensures no off-flavors and maximum durability.
What’s in the Box:
Bottle Filler
Includes gas/liquid triggers and a protective silicone tip
Red Gas Carbonation Cap w/ 6.35mm Male Duotight stem for quick gas line attachment
Duotight Fitting: 1/4" Male Thread x 6.35mm
Duotight Elbow: 6.35mm Compression x 8mm female.
Duotight Ball Lock Disconnect: 8mm Duotight x Yellow/Black liquid QD
EVABarrier Tubing: 5 ft. length (4mm ID x 8mm OD) for low-foaming transfers
The Pluto Beverage Gun is the ultimate hand held beer tap! If you have been dispensing your draft beer out of a standard picnic tap, it's time to upgrade. Definitely one of the coolest draft beer taps that we've seen, this Pluto Beverage Gun is made from nylon and stainless steel. The body is plastic, while the barb, piston, and spring are all stainless. Comes with a 1/4" duotight-compatible barb perfect for use with EVABarrier draft line. You will need either the 8mm x 6.5mm or 9.5mm x 6.5mm Duotight reducer to connect the EVABarrier to the Pluto. Kegland Part number: KL00956
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
Use this lid along with the 65L BrewZilla or DigiBoil and a copper still top (DS120or DS130) to make your own easy-to-use distillery.
The lid gasket has two distinct sides, one that is rounded and one that is completely flat. When installing the gasket the flat side should be facing up. Use one hand to stretch the gasket around the lid and the other to push the gasket into the channel.
This lid has a 1.85" (47mm) hole for the still top. Lid gasket included.
Note: This lid uses a 6mm gasket to better fit the Gen 4 BrewZilla and Gen 2 DigiBoil. It is also backwards compatible with Gen 3 and older BrewZillas and Gen 1 DigiBoils. To improve the seal further, we highly recommend using the Adjustable Lid Clamps with the Distillation Lid if your unit does not have them.
Made from 304 stainless steel
Measures 16.25" in diameter
KegLand Part Number: KL10962
Force carbonate and dispense from your KegLand Mini Keg
Equipped with Gas-In and Bev-Out keg posts for quick and easy attachment of ball lock disconnects
Features a flexible silicone dip tube that draws liquid from the bottom, allowing you to serve from your mini keg whether it's upright or on its side
Includes a 35 PSI pressure relief valve (PRV) for safe and controlled carbonation and dispensing
Force carbonate and serve from your KegLand Mini Keg with the Ball Lock Tapping Head. The Tapping Head features Gas-In and Bev-Out keg posts and PRV rated to 35 PSI. The flexible silicone dip tube will sink and draw liquid from the bottom of the keg, allowing you to dispense from the keg whether it's standing upright or lying on its side, whichever orientation is more convenient for your refrigerator or cooler.
The Tapping Head will add approximately 2.5" to the overall height of your Mini Keg, not including the additional height of your Bev-Out Ball Lock QD. For a more compact dispensing solution, see the Low Profile Tapping Head.
Please Note: The dip tube is designed to fit all Mini Kegs, including the largest 10L size. If using a smaller size keg, we recommend cutting the dip tube to the appropriate length so it doesn't bunch up at the bottom of the keg.
KegLand Part Number: KL06972
Enjoy a never-ending supply of soda water on tap with the Continuous Soda Carbonator Keg Lid. SodaStream units are great, but filling up those tiny 1L bottles is a pain, they're expensive to swap, and they run out quickly. Hook up your mains water supply to this Carbonator Keg Lid, compatible with any standard ball lock homebrew keg, and you'll never have to think about running out of sparkling water. Setup:
Position the keg inside your fridge or kegerator (ideally below 40°F). Attach your beverage draft line to the soda water out post. Attach your gas line to the gas-in post. Set your CO2 regulator to 30-50 psi, depending on how highly carbonated you like your soda water. We highly recommend using a check valve on your CO2 line. On first use, purge the air from the headspace of the keg. Connect the mains water to the water inlet post on the lid of the keg. We recommend also using a check valve on your mains water line to prevent soda water from going back into your house mains. Depending on your mains water pressure, you may need to reduce it using the Duotight In-Line Regulator. For the Carbonator Keg Lid to work well, the mains water pressure should be 10-15 psi higher than your regulator set pressure (from Step 4). That's it. This simple unit will give you continuous soda water connected to your mains water. Please note: if you are using a CO2 regulator that uses a corny-style PRV, such as the KOMOS® regulator, you will need to swap out the standard Green PRV with the 0-100 psi Gray PRV so you can raise the pressure above 60 psi. Always check the pressure rating of your keg(s) before swapping the PRV. KegLand Part Number: KL1095
Counterflow design provides rapid, single-pass wort chilling Larger flow area minimizes hop clogs compared to plate chillers 9.5mm Duotight compatible inlet/outlets allow for quick and easy hose connections Durable PEX tubing resists high temperatures and pressures, extending the chiller's lifespan Tired of slow, inefficient wort chilling? Meet the Red Reaper Counterflow Chiller, your ultimate brewing ally. This isn't just another chiller; it's engineered for speed, durability, and hassle-free brewing. Unleash Rapid Cooling with Superior Design: Robust PEX/Copper Construction: Unlike standard clamped connections, the Red Reaper boasts PEX tubing swaged and soldered directly to the copper wort pipe. This innovative design guarantees a leak-proof, high-pressure connection, ensuring your cooling water stays where it belongs. Lightning-Fast Duotight Compatibility: Seamlessly connect your hoses and camlock fittings in seconds with the 9.5mm Duotight compatibility. Brew more, fuss less. Add the Duotight Push-In Thermowell Tee to add a thermometer to your wort out line. High-Efficiency Counterflow Design: Featuring an internal copper tube for wort circulation and an outer chamber for counterflowing cold water, the Red Reaper maximizes heat transfer for rapid chilling. Experience the power of single-pass cooling from boiling to pitching temperatures. Clog-Resistant Flow: Enjoy the benefits of a plate chiller's efficiency with a larger flow area that minimizes hop clogs. Built for Performance and Longevity: The Red Reaper utilizes the same pressure and temperature-resistant PEX hosing trusted in professional plumbing, offering exceptional flexibility and durability. We recommend recirculating your last 15 minutes of boil through the Red Reaper to sanitize it before chilling with cold water. Easy Cleaning and Maintenance: For optimal cleaning, circulate hot PBW for a minimum 5-minute contact time. Alternate flow direction for thorough cleaning, and rinse with water at the same temperature. Important Care Instructions: Avoid Sunlight: Prolonged exposure to sunlight can degrade the PEX tubing. No Acidic Cleaners: Do not store with StarSan or other acidic products, as they can damage the copper. What is PEX? PEX (cross-linked polyethylene) is a flexible, durable plastic tubing used as a reliable alternative to traditional copper or steel plumbing. Choose Your Fittings: The Red Reaper comes with bare, 3/8" barbs that you can simply clamp your tubing onto. However, we recommend using 9.5mm Duotight x 1/2" male thread adapters which will allow you to convert to your preferred fittings for the water and wort lines -- Camlock, Garden Hose, Tri-Clamp, Quick Disconnect (QD), etc. Specifications: 18.3 ft. Length 3/8" barb inlet/outlet 9.5mm Duotight compatible Rubber feet Hinged hanger (for BrewZilla handles) KegLand Part Number: KL3835
This Duotight reducer is used when stepping down from 9.5 mm OD (D1719) to 8 mm OD EVABarrier tubing (D1717 & D1718). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL06941
Replacement 6 Watt high temperature magnetic drive pump for 110V Gen 4 BrewZillas.
This pump is not backwards compatible with Gen 3 or older units.
KegLand Part Number: KL24358
If you've been looking to step up from fermenting in plastic buckets or carboys, this is an excellent choice for your next fermenter. Stainless steel is a much better option than glass or plastic, as it is extremely easy to clean and virtually lasts forever. There's also much less chance of contamination as stainless doesn't scratch like plastic. Over time, you'll get scratches in plastic fermenters from normal wear and tear, creating microscopic havens for bacteria. Meanwhile, glass carboys are always at risk of breaking which is something you will never have to worry about with stainless steel. The Bucket Buddy is a great value if you're looking for a stainless steel fermenter with built-in heating control. If you live in a cold climate, ale fermentations may be a seasonal affair, as cold ambient temperatures can easily drive down the temperature of your wort below your yeast's optimal fermentation temp range. The Bucket Buddy offers a simple solution with an integrated heating element and digital temperature control. Program your fermentation temperature and if the temp drops below your set point the unit will gently heat your wort from the bottom up via the concealed element located in the base. For cooling, you can place the fermenter in a dedicated refrigerator or drill into the lid to install a Temp Twister Cooling Coil. A temperature controller probe can then be taped to the side of the fermenter to control your cooling source, or you can drill another spot in the lid for a thermowell. Another advantage over carboys and plastic buckets is the domed base inside the fermenter which is great for yeast flocculation when fermentation is complete. The included racking arm will make it easy to transfer out every last drop of beer while leaving the yeast cake undisturbed. The entire racking arm and ball valve assembly is weldless, which means you can remove the assembly to clean and sanitize it between batches. You can even boil the assembly for added assurance that it's been sterilized. To help maintain a steady temperature and cut down on power consumption, the Bucket Buddy pairs well with either the BrewZilla Neoprene Jacket. This unit comes standard with silicone tubing to transfer from the ball valve to your bottles or cans, as well as a stopper and airlock for the domed lid. Specifications: 304 stainless steel construction 17.1 gallon total capacity Digital temperature control 110V / 60W power Stainless steel outlet valve with rotating racking arm Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Please note: Heating capacity is highly dependent on ambient temperature and use of insulation. The 65L Bucket Buddy is appropriate for warm fermentations such as kveik. Adding insulation may increase heating capacity while colder ambient environments may lower heating capacity. KegLand Part Number: KL23061
This mini pressure gauge is compatible with the BlowTie 2 spunding valve, Duotight in-line regulator, and KegLand mini regulator. We recommend using the gauge with a range closest to your desired pressure setting. If you'd prefer a digital instant read gauge, check out the Digital Mini Pressure Gauge (for gas applications only). Pressure Range: 0-150 psi (0-10 bar) Body Dimensions: 26mm x 26mm x 15mm Probe Diameter: 8mm WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Note: These gauges are accurate to 10% of the whole pressure range. (ie the 0-30psi Gauge is accurate to +/- 3psi). KegLand Part number: KL1501
Easily identify gas and beverage lines with color-coded options—LightShield Black for beverages, Transparent Red for gas EVABarrier's double-walled design with a proprietary inner polymer significantly reduces oxidation and CO2 loss, keeping your beer fresher for longer The ultra-smooth, nearly impermeable inner surface of the tubing prevents bacteria and microbes from adhering, ensuring cleaner beer lines The stiff yet pliable EVA outer barrier makes the tubing kink-resistant and ideal for use with push-in fittings like Duotight and John Guest 4mm ID size is optimized for home draft systems with short 5-6 ft. draft lines Easily identify your gas and beverage lines with color-coded draft tubing. LightShield Black EVABarrier is recommended for beverage lines while using Transparent Red for your gas lines, saving you a headache when your draft lines inevitably get tangled up in your draft system. LightShield Black also works perfectly for hydroponic systems as it will block UV and discourage algae growth. If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 4 mm (5/32") ID size is perfect for homebrew draft applications where only a short beer line is needed. We recommend using 5-6 ft. per line for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 4 mm (5/32") Outer Diameter - 8 mm (5/16") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. KegLand Part Number: KL42765
Tune the Stout Spout on your Intertap or NukaTap faucet with this set of perforated discs! Not all beverages are the same so this kit offers a range of aerator discs so you can find the perfect disc for your stout or cold brew coffee. The Stout Spout has a removable creamer/aerator disc inside. It is specially made to serve beers infused with nitrogen gas, and allows the nitrogen gas to flow smoothly through the faucet with the beer to create a smoother, creamier beer. With this range of discs, you can mix and match with ease to find which one serves your particular beverage justice with more restriction or more areas for that creaming effect to push through the spout. Kit Contains: 0.3mm Drilled Disc with 3 x holes 0.3mm Drilled Disc with 5 x holes 0.5mm Drilled Disc with 1 x hole 0.5mm Drilled Disc with 3 x holes 0.5mm Drilled Disc with 5 x holes 0.7mm Drilled Disc with 1 x hole 0.7mm Drilled Disc with 3 x holes KegLand Part Number: KL12591
This simple tee fitting allows you to turn a PET growler or repurposed soda bottle into a pressurizable growler or mini keg system. PCO 1881 threading on all ends—the most common threading for plastic soda bottles. One end is female threaded to attach to your vessel, and the other ends are male threaded in order to accept two Carbonation Cap Ball Lock Adapters. A small length of 3/16" ID tubing can be attached to your bev-out cap to function as the dip tube. If you're using EVABarrier tubing, simply connect using a Duotight reducer. Tee fitting only. Does not include Carbonation Caps or PET bottles. KegLand Part Number: KL14830
Replacement 1/2" KegLand Quick Swivel Connector Nut. Comes with a heavy duty silicone grip guard allowing comfortable and quick tool-free operation. Silicone O-ring included.
KegLand Part Number: KL31547
Use this valve with a standard soda bottle as an inexpensive and effective dry hopping solution Attaches to the PCO 1881 threaded port on the FermZilla fermenter's lid Carbonation Cap and Tee Piece can be added to allow for purging the hops with CO2 This really handy stainless adapter ball valve will enable you to connect two PCO 1881 threads with a valve in between. Each side has an integrated O-ring that will seal on the neck of the PCO1881 Thread. Ideally suited to making a dry hop device for FermZilla with a standard soda bottle or PET growler with PCO 1881 threaded neck. As shown in the photo, if you use this stainless ball valve in conjunction with the PCO 1881 Tee Piece and the Carbonation Cap, you will have the added advantage of being able to use CO2 to purge out oxygen from the hops before you dry hop. This assembly makes an inexpensive and very effective dry hopping tool. Please note: Dry hop pellets will require a bit of a shake to get them to fall through the 3/4" bore. Tapping the PET bottle should be enough to make the hops fall down into the fermenter through the ball valve. KegLand Part Number: KL18074
Includes the newest Gen 3 POK cup seal washers Provides a full set of seals to quickly fix leaks, replace lost seals, or maintain taps used in demanding settings Compatible with all standard NukaTap beer faucets (not suitable for the flow control model)
This handy kit contains all the seals needed for the standard NukaTap stainless beer faucet. Regardless of which generation of seals your faucet came with, you can replace or upgrade them with the Gen 3 POK cup seal washers. For the NukaTap Flow Control seal kit, see here. Most of the seals in this kit are durable and won't require frequent replacement. However, if you experience a leak, accidentally lose a seal, or use the tap in a demanding commercial environment, this kit has you covered. When replacing seals, we recommend applying a food-grade lubricant to ensure a long-lasting and secure fit. As you take the tap apart, it can also be helpful to take a picture or make a note of where each seal is located to make reassembly easier. Includes: The Nuke! Tap Coupling Washer Bonnet Washer 2 x Black Generation 3 POK Cup Seal Washers Nozzle Washer How to tell what generation NukaTap you have:
Generation 1 - Two White Nylon Cup Seal Washers Generation 2 - Two Red Self Lubricating Nylon Cup Seal Washers Generation 3 - Two Black POK Cup Seal Washers KegLand Part Number: KL43021
The ultimate portable draft faucet! Compact & lightweight with all the advantages of a standard NukaTap forward sealing faucet Pair with a Flow Control Ball Lock QD & Duotight Adapter and the whole assembly fits in your pocket Forward-sealing design prevents beer residue from gumming up the faucet Reduced first pour foam due to low thermal mass and conductivity Perfect for mobile draft, mini kegs, sampling from fermenters, and can even be installed on your kegerator or keezer Mini Design – Ideal Flow Rate for Small Systems Most conventional beer faucets are designed with 3/8" diameter spouts so you can pour a pint in just over 10 seconds. This type of flow rate is great for high turnover bars and commercial venues but isn't necessary or even desirable for all applications. For compact portable systems and home draft systems, a slower flow rate is easier to control and further reduces foaming issues due to the low liquid volume stored in the body of the faucet. The NukaTap Mini is also more ideal for pouring smaller doses. For example, cocktails where 5-8 oz of liquid is dispensed is difficult to control with a high flow rate tap. For portable systems, the NukaTap Mini with the Flow Control Ball Lock QD & Duotight Adapter assembly is small enough to literally put in your pocket, making it ideal for mini keg setups that you want to be portable or that you want to easily fit inside a domestic fridge where space is tight. Forward Sealing Forward sealing faucets are absolutely the way to go when it comes to beer taps. Old legacy taps still exist in the industry that are simply poorly designed. The issue with rear sealing faucets is that beer dries up on the internal piston. Aside from being unsanitary, as more and more beer dries up in these components the faucet can almost glue completely shut causing damaged seals or broken handles (this is particularly the case if it's left for some time to dry out with beer inside). These older legacy designs still exist probably due to poor education. The forward sealing designs do not have this problem and the tap drains out completely with no beer drying up on the mechanical moving parts in the same way. This makes the tap more sanitary and reduces maintenance. In many instances the price is similar so there is no reason to use a poorly designed rear sealing faucet. All NukaTap faucets are forward sealing. Laminar Flow Just like the NukaTap SS and NukaTap FC, the NukaTap Mini has been designed with laminar flow in mind. Laminar flow is critical for a beer tap as it means you will pour the beer with minimal foaming and a substantial reduction in wastage. Think about how many times a beer faucet opens and closes in its lifetime. 1,000 or maybe 10,000 times? Laminar flow saves wasted beer in excessive foam and the better laminar flow easily pays for itself in a reduction in lost beer. To use poorer designed faucets is essentially flushing money down the sink. Extensive modeling has been done on the NukaTap design to improve laminar flow. Integrated Seals That Are Indestructible and More Sanitary Unlike other designs, the NukaTap Mini body is made from Polyketone (POK) making it strong, robust, and able to be autoclaved. The seals are also over-molded from Santoprene® making them hard wearing so they will literally last for the lifetime of the tap without the need for replacement. Santoprene® and POK both have excellent resistance to chemicals such as caustic soda, peroxide, phosphoric acid, lactic acid, citric acid, acetic acid, and all common chemicals sold and used in the beverage industry. The seals internally are over-molded meaning no fissures or cracks exist for bacteria, crud, or yeast to hide. Superior First Pour Foam Due to Low Thermal Mass and Conductivity First pour foam is an issue caused by a warm tap body. For most faucets to pour well it's important to dispense enough beer to cool the tap body down to reach maximum performance. In addition to this the conductivity of the tab body also makes this worse so insulative materials simply work better than conductive materials. The NukaTap mini not only has very low thermal mass but is also highly insulative being made mostly from Santoprene® and POK. The combination of these two factors in conjunction with superior laminar flow makes for the lowest "first pour foam" effect out of any tap ever produced. Long Shank Alternative Most conventional beer faucets require a large 3/4" hole to be drilled through the side of your refrigerator, keezer, or cold box wall. Traditional long shanks also generally have a large volume of liquid that sits inside the wall unrefrigerated which is not ideal. New long shank alternatives developed for the NukaTap Mini are designed to suit any wall thickness and greatly reduces the stagnant beer sitting in the shank itself. For walls up to 2.7" thick, these wall mount shank kits include three screws, however if the wall is thicker, you can also use 6 small wood screws or something similar and attach three screws from the front and 3 from the back allowing you to go into any wall type. Another advantage of this new design is the tap will never accidentally rotate. Typically, other long shank beer taps rely on the hex nut on the shank to be done up tight enough to prevent rotation but if the wall compresses (often the case with foam walls) the tap is allowed to rotate. This new design has three fixing points making it impossible for the tap to rotate accidentally as the interlocking teeth behind the collet allow you to set the angle and then do up the collet to fix the tap permanently in that position. NukaTap Mini Accessories (Sold Separately): Duotight Flow Control Ball Lock QD (DUO159) Mini Self Closing Spring (D1598A) Duotight Adapter - 8mm (D1598B) Long Shank Alternative for Wall Mounting - Duotight 8mm (D1598C) Long Shank Alternative for Wall Mounting - Duotight 6.35mm (D1598D) Stout Spout (D1598E) Vertical Clamp On Assembly (D1598G) Horizontal Clamp On Assembly (D1598H)
The HIZO G14 Portable Gas-Fired Pizza Oven is the perfect no-hassle solution to cooking the best homemade pizza outdoors
Fast. Heats to 932°F and cooks a pizza in 1 to 2 minutes
Easy. No assembly required. Built-in gas ignition and adjustable heat control dial for temperature control
Portable. Retractable legs and optional carry bag make it easy to transport and set up—just click the switch and start cooking
14" is the perfect size. 12" ovens are too small and 16" ovens are oversized and twice the price.
Making homemade pizza in your kitchen oven is a tasty and rewarding endeavor, but nothing matches the performance and results you get from a purpose-built pizza oven. Kitchen ovens generally max out around 550°F whereas pizza ovens can reach as high as 1,000 degrees. The ideal way to cook pizza is quickly and at very high temperatures in the 800-900°F range, so if you want to take your homemade pizza game to the next level, a gas-fired pizza oven is the way to go!
The HIZO G14 Pizza Oven is propane powered and ready to use straight out of the box with no bolts or tools required for assembly. Complete with dialed control and gas igniter included as standard—no batteries or matches required! Setup and packing away couldn't be easier thanks to the four stable folding legs.
Includes:
HIZO G14 Pizza Oven
Liquid Propane hose and regulator
Dual Scale Temperature Gauge: 32°F - 932°F (0°C - 500°C)
Ceramic Pizza Stone: 14" x 14" x 3/8"
Recommended Accessories:
Waterproof Carry / Storage Bag (FPE202)
Infrared Laser Thermometer (MT401)
12"or 14" Perforated Pizza Peel (FPE205 / FPE206)
8" Round Pizza Spinner (FPE204)
4" Pizza Cutter (FPE203)
Effortlessly transport your 35L or 65L BrewZilla or 65L DigiBoil with the sturdy rolling flat dolly, designed with precut hole configurations for secure placement Includes two locking wheels to hold your brewing system in place, ideal for cleaning on sloped surfaces or ensuring stability during use Perfect for Lift-N-Lock Pulley systems, enabling seamless movement under pulleys and convenient handling of malt pipes Easily move your BrewZilla or DigiBoil around your brewing area using this rolling flat dolly. The thick reinforced plastic dolly plate comes with two precut hole configurations suitable for 35L & 65L Gen 4 BrewZillas and 65L DigiBoils, allowing the feet of your system to slot into place for easy mobility. Two locking wheels are included so you can lock your brewery in place which can be especially useful if you move the unit to a sloped driveway for cleaning. These dollies are highly recommended if you are using a Lift-N-Lock Pulley type system for your malt pipe. Easily move your system into position under your pulley, and when you're done mashing, pull the malt pipe out, wheel the BrewZilla away, and lower the malt pipe to the ground or into a cleaning tub. The Low Profile Dolly Bundle is an economic choice recommended for 35L units and for brewers that have a relatively even surfaced brewing area with little to no obstruction. If you need something a little more rugged to handle uneven pavement or roll over power cords more easily, we recommend the Heavy Duty Dolly Bundle. Please take note that the bolts are pushed through from the bottom rather than top down. Compatible With: 35L BrewZilla Gen 4 65L BrewZilla Gen 4 65L DigiBoil Includes: Reinforced Plastic Dolly Plate 35 mm Castor Wheels (2 locking, 2 non-locking) Mounting Hardware Plate Dimensions: 21.6" Ø x 0.7" Thick (550 mm x 20 mm) BrewZilla sold separately
KegLand Part Number: KB11113 NOTE: Unfortunately due to the feet placement, the dolly plate is not suitable for the 35L Gen 3.1.1 BrewZilla or 35L DigiBoil.
This is a complete replacement silicone tubing kit for the pump and ball valve tubing on a 65L Gen 4 BrewZilla with 6 Watt Pump. Made from food grade silicone and temperature resistant to 356°F (180°C).
KegLand Part Number: KL24778
It is really THAT easy to make good beer at home?+
YES! If you can follow a recipe and keep clean, there is nothing stopping you from making great beer in your home - beer you can be proud of and your friends will love! The MoreBeer! mission is to provide reliable equipment and quality ingredients that make the home brewing experience successful and satisfying. We'll get you started in home brewing the way we wish we had been started.
