KegLand is a high quality homebrewing equipment brand based out of Australia. We offer a wide variety of their products, from BrewZilla all-in-one system and DigiBoil eletric kettles, to pumps and grain mills. KegLand beer products are an incredible value, as they combine quality craftsmanship with low prices!
KegLand
-
Flanged Tri-Clamp Gasket | Silicone | 1.5"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections Silicone gaskets have a wide temperature range and are recommended for hot side applications For 1.5" tri-clamp connections Flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both Silicone and EPDM. Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 1.5" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F KegLand Part Number: KL44837
$2.19
-
Tri-Clamp Gasket with Stainless Mesh Screen | 7 Mesh | Teflon | 4"
Teflon gasket with 304 stainless mesh screen for 4" tri-clamp connections. Can be used as a filter screen to trap large particulates passing through T.C. fittings. Often used for distillation to retain activated carbon for filtering neutral spirits or used in pot distillation to retain botanicals in the vapor stream. The screen has a mesh size of 7 which will block particles larger than 2.83mm or 2830 microns. This slightly larger mesh size makes this screen ideal for use in a distillation basket. KegLand Part Number: KL28394
$12.49
-
Nukatap® Counter Pressure Bottle Filler | Replacement Dip Tube
Replacement telescopic dip tube for the Nukatap Counter Pressure Bottle Filler.
$5.49
-
Replacement Wrench Set for Cannular Can Seamer
Replacement wrenches that comes included with the Cannular Can Seamer. KegLand Part Number: KL13192
$8.79
-
Neoprene Insulating Keg Parka for Oxebar Mono PET Keg | 8L
Keep your beer colder for longer with the insulating neoprene material Prevent dings and scratches during transport with an internal bump cap Easily carry your keg using the removable shoulder strap The zippered design makes it simple to put on and take off Tailormade for the 8L Oxebar Mono PET Keg Keep your beverage colder for longer with the Oxebar Neoprene Jacket. This parka is more than just a cozy sleeve for your keg; it's designed with a rigid internal "bump cap" to prevent those annoying scratches and scuffs that can happen when your keg is being moved around. Made from durable neoprene, this jacket helps maintain the temperature of your beverage, whether you're taking it to a party or just keeping it chilled in the fridge. The Oxebar Neoprene Jacket protects your keg while helping your beer stay crisp and cold. KegLand Part Number: KL42895
$32.99
-
Duotight In-Line Regulator | 0-150 PSI | Liquid & Gas Compatible | 8 mm Duotight
Easily set different pressures downstream from a single CO2 regulator. Serve different beverages at different pressures without the need for expensive regulator manifolds! Compatible with both liquid and gas 8 mm Duotight inlet/outlet for use with 8 mm OD EVABarrier tubing or 8 mm Rigid Joiners The Duotight In-Line regulator works with both gas and liquid. Easily adjust the flow with the yellow adjustment knob. 8 mm Duotight fittings at both inlet and outlet make this unit perfect for use with EVABarrier 8 mm OD tubing (D1717 or D1718). Suitable for applications ranging from 0-150 psi. Since this unit does not have a built-in pressure gauge, it can be used in the full pressure range without ever needing to purchase or swap out the gauge. We recommend using an adjustable relief valve/spunding valve on your keg to set the pressure. Stepping Down Pressure The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability. Ideal regulation scenario (10 PSI less than inlet pressure) Example of 30 PSI inlet translating to 0–20 PSI output This regulator is perfect for lowering your mains water pressure for use with the Continuous Soda Carbonator Keg Lid. Specifications: Pressure Range: 0–150 psi Suitable for mains water pressure Liquid and gas compatible Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends Wall mountable Made from non-corrosive acetyl, nitrile, and stainless parts KegLand Part number: KL02172
$10.49
-
Kegland | JetKeg | Keg Backpack
Serve beer on the go with the JetKeg Keg Backpack Fits up to a 5-gallon homebrew keg or sixtel commercial keg Made with durable buckles and strong nylon shoulder and waist straps Fully insulated to keep your keg colder for longer Includes the Pluto Beverage Gun and EVABArrier tubing for dispensing Mobile draft dispensing has a whole new meaning with the JetKeg Backpack from KegLand. Strap a keg to your back and walk through a crowd, dispensing delicious beer as you go. You'll have more followers than the fabled Pied Piper in no time. The backpack is fully insulated to keep your keg colder for longer, and features hot tape sealed seams on the inside to prevent leaking. If you've ever felt too anchored down serving beer from yet another booth at the festival, the JetKeg is the solution. Load up a 5-gallon homebrew keg or sixtel sanke keg and join the fray! The JetKeg Backpack comes with the Pluto Beverage Gun, a precut length of EVABarrier tubing, and Duotight reducer to connect the tubing to the Pluto Gun. It does not include any gas side equipment, and you will need additional fittings depending on whether you'll be using it with a homebrew keg or commercial keg. Includes: JetKeg Backpack 1 x Black Nylon Pluto Gun (Duotight compatible) 1 x 6.5mm x 8mm Duotight Reducer (for Pluto Gun) 1 x Precut length of 4mm x 8mm EVABarrier tubing Please note the example photos show accessories that are not included with the JetKeg. Does not include keg, gas fittings, keg coupler, CO2 cartridges or cylinder. For Ball Lock Kegs, we recommend using the Mini CO2 Regulator Kit with a 74 g cartridge for your gas supply. Then use a flared ball lock disconnect with Duotight x Flare adpater to connect the Pluto Beer Gun to your bev out post. For Sanke Kegs, we recommend using the Mini CO2 Regulator Kit with a 74 g cartridge for your gas supply. The Mini Regulator can connect to a D-Style keg coupler with the Gas-In Sanke to Ball Lock Adapter. The Pluto Beer Gun can be connected to the keg coupler beverage out with the Duotight x Beer Thread adapter. KegLand Part Number: KL12560
$76.99
-
Replacement Seal Kit for KegLand Core 360 Mini CO2 Regulator
Contains the o-rings for the piston, the red inlet washer, MK4 seat assembly o-ring, 2 x barb MFL outlet o-rings and a thumb screw o-ring. For instructions on replacing the seals and/or general maintenance please refer to the product manual below. KegLand Part Number: KL12584
$7.69
-
Duotight Push-In Fitting - 9.5mm (3/8 in.) Female Bulkhead
This Duotight fitting is designed to go through the wall of a tank, housing, or wall, similar to a pass through shank, so you can run EVABarrier tubing from one side to the other. Compatible with EVABarrier 9.5 mm OD tubing (D1719). With the lock nuts in place, there is approximately 1" of pass through threading. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. KegLand Part Number: KL21012
$3.89
-
KOMOS® Kegerator Heavy Duty Wheel Upgrade | 4 Casters | Standard & Deluxe Models
Upgrade the wheels of your Komos kegerator to these heavy duty 100mm wheels. Each wheel is rated up to 220 lbs and made with steel bearings. Includes 2 locking and 2 non-locking wheels. Compatible with Standard and Deluxe models. For the Double-Wide model, see here. Includes 2x locking wheels and 2x non-locking. NOTE: The locking wheels need to be attached on the non-hinged side of the door as the hinge will get in the way of the locking mechanism. Mounting screws are not included.
$69.99
-
Cannular Can and Bottle Filler | WiFi Antenna Upgrade
External WiFi Antenna Upgrade for the Cannular Can and Bottle Filler. If your filler is experiencing connection issues, this antenna will help boost signal reception. Only suitable for the Cannular Can and Bottle Filler (CAN250). Not suitable for other RAPT devices. See here for the Antenna Upgrade Installation Guide. Please Note: Cannular Can and Bottle Filler purchased after 7/1/2025 will come with an upgraded WiFI antenna as standard.
$19.99
-
Brewzilla Sight Glass Connection Kit | Stainless Steel Ball Valve & Elbow
This BrewZilla PPSU sight glass stainless steel ball valve and elbow use radial seal O-rings to form a strong, leak-free connection. Two in the ball valve and two in the bottom elbow. When assembling the sight glass to upgrade your existing Gen 3 or Gen 4 BrewZilla, you will reuse the female camlock x female 1/2" fitting that comes on the recirculation arm, or you need to purchase a separate fitting for the end of your custom build. You will also need plumbers tape or food grade Loctite to assemble the ball valve with the camlock fitting. Rather than purchasing the parts separately, Gen 3 and Gen 4 BrewZillas can be upgraded with one of these sight glass kits. KegLand Part Number: KL33817
$27.49
-
Semi-Automatic Label Applicator Machine for Self-Adhesive Labels | Date Printer | 110V
Designed to streamline your labeling process, saving you time and effort. Apply self-adhesive labels quickly and efficiently. Adapts to various sizes and shapes, making it suitable for labeling bottles, cans, jars, or other containers Accurate and Precise: Achieve professional-looking results every time with consistent label placement and adherence Date Coder automatically prints your programmed packaging date onto the label For some homebrewers, the most satisfying aspects of the brewing process is when you hand someone a bottle or can of your latest creation. At this point, presentation is everything, and that begins with a beautifully packaged beer. Using a 3rd party, you can design your very own adhesive labels for bottles or cans, then apply them with perfection using KegLand's Semi-Auto Label Applicator. This semi-automated compact label applicator machine is suitable for bottles, jars or cans of up to 160mm diameter and is fully adjustable for labeling any cylindrical container. Apply self-adhesive labels to your beer, wine or spirits quickly and easily. This version KegLand's Label Applicator includes a date coder to print the packaging date onto the label. This is generally only needed for commercial applications, and if you'll be using the label applicator for personal use, we would suggest the more affordable option without the date coder (CAN310). Specifications: Power: 110V 60Hz Min Label Thickness: 5μm (0.005 mm) Max Label Height: 150 mm (5.9") Max Label Length/Width: 300 mm (11.8") Max Label Roll Diameter: 280mm (11.02") Max Label Roll Inside Diameter: 76mm (2.99") Max Vessel Diameter: 160 mm (6.2") Label Applicator Speed: 1–3 seconds (varies by label length) Approx. Dimensions: 21.6" L x 9.8" W x 13.7" H Data Coder: Fully adjustable position, automatic operation, date code stamps included KegLand Part Number: KL20329
$1,209.99
-
HIZO Cast Iron Double-Sided Skillet
Compatible with the HIZO G14 Pizza Oven or any backyard grill! Conveniently pre-seasoned—simply wipe with a wet cloth and pat dry Double-sided with a smooth, flat side and raised grill grooves on the other Raised lips on both sides to keep in the juices and oils Perfect for the HIZO G14 Pizza Oven or your backyard grill, the double-sided griddle and flat skillet plate is the heavy-duty heat-retention cooking utensil you need in your arsenal. Weighing in at a whopping 9 lbs, this thick cast iron plate can really hold the heat! The HIZO double-sided skillet has a flat, smooth griddle side, and raised grill grooves for the other side. Both sides have a raised lip to handle some juices and oil to fry in. It can be moved around easily by the two removable handles in three location points on the plate. Directions for First Use: Conveniently pre-seasoned—simply wipe with a wet cloth and pat dry For super sizzling restaurant-style hot plate, preheat on high for at least 20 minutes Dimensions: 12" x 12" x 1" KegLand Part Number: KL24907
$54.99
-
Replacement Lock Nut for AlcoEngine Still Tops
Replacement lock nut for AlcoEngine Copper Pot Still and Copper Reflux Still.
$6.59
-
Replacement Malt Pipe Top Screen for BrewZilla | Probe Hole | Gen 4 | 65L
Specifically designed for maximum strength and rigidity. This redesigned top screen features a hole for the probe of the RAPT Bluetooth Thermometer for monitoring and controlling your BrewZilla Gen 4. KegLand Part Number: KL27373
$38.49
-
Drip Tray | Countertop Drip Tray | Removable Grill | Stainless | 11.8 in.
Keep the top of your kegerator clean with this stainless steel countertop-style drip tray. Perfect for placing underneath a draft tower or 2 faucets mounted side-by-side. Removable grill for easy cleaning. Features 5 pressed locations for drilling through and plumbing the drip tray for draining. Features: Removable grill Made from stainless steel 11.8" L x 6.7" W x 0.6" D Kegland Part number: KL13161
$29.99
-
Universal Body Connect for Gas and Bev - Ball Lock
This nifty ball lock post is compatible with both gas and liquid ball lock disconnects. A great way to modify your homebrew kegs so you can daisy chain them together, or hook up your gas line to the bev out dip tube to carbonate your beer faster. It is important to note that due to dimensional differences between gas and liquid posts, this item will not form as snug a fit as a dedicated post for gas disconnects. We do not recommend this to be used as a dedicated gas post. Please note that this is just the post. You will need to purchase the poppet and spring separately. Thread: 19/32-18 Kegland Part Number: KL08662
$10.99
-
Brass Hex Nut for Draft Shanks
Replacement brass hex nut for standard beer shanks. KegLand Part Number: KL06286
$4.39
-
KegLand Ball Lock Quick Disconnect (QD) | Replacement Seal
Replacement seal for barbed or flareed stainless ball lock quick disconnects from KegLand. Compatible with KEG732, KEG734, KEG745, & KEG746.
$1.09
-
BrewZilla | Replacement Silicone Tubing Kit for 25W Pump | Gen 4 | 65L
This is a complete replacement silicone tubing kit for the pump and ball valve tubing on a 65L Gen 4 BrewZilla with 25 Watt Pump. Made from food grade silicone and temperature resistant to 356°F (180°C). KegLand Part Number: KL39772
$15.99
-
Cannular Can and Bottle Filler | Replacement Power Supply
Replacement Power Supply for the Cannular Can and Bottle Filler. 24V DC. 110V plug. KegLand Part Number: KL37730
$14.49
-
KegLand Quick Swivel Connector | 1/4" Straight Barb | 6.35 mm Duotight Compatible
This straight barb in 1/4" (6.35mm) OD is only compatible with the 1/2" KegLand Quick Swivel Connector Nut. Compatible with 6.35 mm Duotight fittings. Quick Swivel Nut sold separately. KegLand Part Number: KL31554
$3.99
-
KegLand Fruit Press | Replacement Needle Bleed Valve
Replacement needle bleed valve for the KegLand 40L Fruit Press.
$5.49
-
Replacement Boiler False Bottom for BrewZilla | Pump Filter | Gen 4 | 65L
This false bottom is specifically designed for the Gen 4 65L BrewZilla. On this model the ball valve tap was relocated underneath the unit, allowing for a super low profile false bottom that molds itself to the concave bottom of the BrewZilla. This also allowed for a larger malt pipe for bigger grain bills and provides a filter for protecting the easy access pump. It is not suitable for DigiBoils or Gen 3.1.1 or older BrewZillas, as those models do not have a concave bottom. Please Note: These are slightly looser in fit for ease of use. These only come with one eyebolt as the spec change means that the additional eyebolt is no longer required. KegLand Part Number: KL27311
$54.99
-
RAPT Fermentation Chamber | Polycarbonate Heat Resistant Shelf Tray
Heat resistant shelves for your brand new RAPT Fermentation Chamber. Can be used for trays of mushrooms or seed sewing with added grow lights. It can also be used as a humidity tray if you require a humid environment for your project. 60 mm (2.3") deep. KegLand Part Number: KL25553
$43.99
-
FermZilla Flat Bottom Fermenter - 7.9 gal. / 30 L | Starter Kit
Get on your way to making delicious beer with the FermZilla Flat Bottom Starter Kit. The kit includes the 30L Flat Bottom FermZilla as well as the most precious brewing tools you'll need when making your first batch and beyond. Bottle capper, hydrometer, bottling wand and more, all bundled together at an unbeatable price. The FermZilla Flat Bottom Fermenter is an excellent option for making all kinds of beverages, from beer and wine to kombucha and cold brew coffee. It's compact, lightweight, and made of brilliantly smooth PET. The extra-large lid opening makes it easy to get your arm inside and scrub the walls clean after use. The Flat Bottom features the same lid as the Conical FermZilla's, so installing accessories like a thermowell or Temp Twister Cooling Coil couldn't be easier. Why MoreBeer! loves the Flat Bottom FermZilla: Super smooth PET makes cleaning very easy. Tight-sealing lid and PET material make for a better oxygen barrier than fermenters made of HDPE. Lightweight and easy to move around, yet strong enough to be considered shatterproof. The 4.75" lid opening makes it easy to get your arm inside and clean after use. The lid is designed for the easy installation of accessories such as a thermowell or cooling coil. Affordable! The Flat Bottom is one of the most affordable plastic fermenters in this size range. What's Included: FermZilla 30L Flat Bottom Fermenter 3-Piece Airlock Adhesive Thermometer Adhesive Voume Marker Siphon Bottling wand Beverage tag (4) Sachets of cleaning powder (100) Crown bottle caps Bottle capper Hydrometer Bumper stickers Specs: 30 L (7.9 gal) Total Volume Temperature Rated to 122°F Height - 18.5" Height w/ Airlock - 22.5" Tank Diameter - 13.75" Lid Ports - 28 mm PCO 1881 threads Please note: The Flat Bottom is not pressure rated and was not designed to carbonate in. For this reason, the lid does not come with a PRV like that which is included with the Conical FermZilla. The tank can withstand approximately 2 psi, but beyond that there is risk of deforming and damaging the tank. Kegland Part number: KL13550
$98.99
-
FermZilla Tri-Conical Easy-Grip Pressure Fermenter Starter Kit | 55L | 13.2G
A best seller for a reason! Tons of features at an incredible cost Crystal Clear super smooth PET makes fermenting and cleaning super easy 3" Butterfly valve at bottom makes removing yeast/trub easy with the 600mL collection jar. Pressurizable for fermentation and closed transfer to your keg Includes BlowTie spunding valve kit, red & yellow carbonation caps, and floating dip tube as standard The FermZilla is the perfect option for brewers that want all the advantages of a conical fermenter without the price tag of a full-blown stainless-steel unit. It allows you to dump trub, harvest yeast, and with the addition of CO2 cylinder and regulator, you can carbonate and serve – all in one vessel! The clear PET tank allows you to visually monitor fermentation activity and is pressure rated to 2.4 Bar (34.8 psi), which means you can ferment under pressure, reducing ester and fusel alcohols in your finished beer. This also gives the ability to perform pressure transfers. If you prefer to move your finished beer to a keg or other vessel, you can do so with little to no oxygen exposure. The FermZilla Tri-Conical Easy-Grip model comes packed with accessories so you can take full advantage of this pressurizable fermenter on day one. The new stock standard includes Easy-Grip threaded lid ring, BlowTie spunding valve with integrated pressure gauge, ball lock carbonation caps for the lid and collection container, floating dip tube kit with weighted filter, volume marker graduation sticker, and adhesive thermometer. What's Included: FermZilla 55L Tank with 3" T.C. Bottom Port Easy-Grip Threaded Lid Ring Integrated Gauge BlowTie Kit Spunding Valve (0-15 psi) Silicone Dip Tube Kit with Yellow Weighted Filter and SS Float (2) Yellow Liquid Carbonation Caps (2) Red Gas Carbonation Caps Fermzilla Pressure Lid with Red PRV (35 psi) 3" T.C. Butterfly Valve 600 mL Collection Container with 3" T.C. Connection Stainless Steel Stand with Swing Handles 3" tri-clamp with gasket Graduation Sticker Adhesive Thermometer Specs: 55 L (13.2 gal) Total Volume Pressure Rated to 2.4 Bar (34.8 psi) Height in Stand - 41.5" Tank Diameter - 13.9" Diameter in Stand - 15.3" Lid & Collection Container Ports - 28 mm PCO 1881 threads Temperature Rating: When not under pressure, do not expose to liquids above 131°F When under pressure, do not expose to any temperatures above 95°F* *Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years. Please note: when using the FermZilla under pressure, you must perform a water pressure check to ensure your connections are leak proof. To do this, fill your FermZilla up with water, apply at least 15 psi pressure, and check for leaks around all caps and threads. Pressure Stress If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple: Fill the tank to the brim with water Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher Pressurize the tank to 4 BAR (58 psi) Check for leaks, then replace the Red PRV when finished If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla. General Care Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank. KegLand Part number: KL47302 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary. FermZilla Tri-Conical 27L & 55L | User Guide
$199.99
-
A-Style Keg Coupler | German Slider Beer Tap | Stainless Steel Body & Probe | PRV | Beer & Gas Barbs Included
A-Type keg coupler fits most German beer kegs such as Paulaner and Spaten Click-to-engage ergo lever handle Includes 1/4" OD barbs for gas inlet and liquid outlet Barb elbow outlet is ideal for low clearance keg storage and easier line routing For Paulaner or Spaten keg, this is an A-Type keg tap. Also known as a keg coupler, keg tap, coupling, or adapter. Both barbs measure 3/16" ID and 1/4" OD. This model features a pull-ring pressure relief valve (not pictured). This Keg Tap Will Usually Fit: Ayinger Bitburger Pilsner Delirium Tremens (Belgium) Erdinger Hefetrub Weisse Fischer Franziskaner Hefe-Weisse Hacker-Pschorr Weisse Hoegaarden White Isenbeck Krombacher Kronenbourg 1664 Paulaner Spaten Staropramen Victoria Bitter Warsteiner KegLand Part number: KL06057
$58.99
-
NukaTap® Mini Beer Faucet | Wall Mount Shank Kit | 6.35 mm Duotight
Designed specifically for mounting the NukaTap Mini Beer Faucet on any kegerator, keezer, cold room wall, or other flat surface Connect beer line directly to the faucet, reducing the amount of temperature loss to a standard draft shank No spinning faucets. Your tap will remain in a fixed orientation once locked into the collet Easy installation. No need to drill a large hole through your fridge to accommodate a standard 5/8" draft shank Use with 6.35 mm OD EVABarrier draft tubing This shank kit is specifically designed to suit the NukaTap Mini Beer Faucet and will allow you to connect the NukaTap Mini to a cooler box, kegerator, keg fridge, cold room wall or any other flat surface. This wall mount shank kit is for use with 6.35 mm OD EVABarrier. For the shank kit for use with 8 mm OD EVABarrier, see here. New Innovative Shank Design Unlike other shank kits, this kit doesn't use a bulky 5/8" threaded shank. The issue with a standard draft shank is that acts as a heat sink, and due to the fact that most shanks sit inside an insulated wall, this results in a substantial amount of warm beer coming out of the tap before cold beer starts flowing. This results in substantial "first pour foam" effect which wastes beer, can result in sour beer, and ultimately negatively effects the quality of the beverages being served. This new design has the beer line feed all the way directly up to the back of the faucet, greatly reducing the volume of non-refrigerated beer. No Spinning Shanks If you have ever installed a traditional 5/8" long shank, you will know how frustrating it is when you use the faucet and it starts rotating. This new design of shank alternative uses three screws that lock the tap into a fixed position and prevents the taps from rotating. If you loosen the 1/2" stainless tap collet you can still have the flexibility to rotate the faucet to any orientation, but once the collet is tight, interlocking teeth on this shank kit and the NukaTap Mini will hold the tap permanently in the correct orientation. Easy Installation Another advantage compared to standard shanks is that this kit doesn't require you to drill a large 3/4"-1" hole through the wall. As no shank is required, only a hole large enough to accommodate the beer line is required. As a result, an 8mm (5/16") conventional drill bit is all that is necessary for installation. However, if you are concerned about the small amount of beer sitting in the draft line inside the wall not being refrigerated, you can also shell out a larger diameter of foam on the inside of the wall to allow cold air to circulate around the beer line thus reducing the non-refrigerated beer in the line even more. If you wanted to do this the Step Drill Bit is the best tool for the job. Any Wall Thickness Other shank kits will require you to purchase a specific length shank for a specific wall thickness. This new shank alternative will fit any wall thickness. If you have wall thicknesses that are less than 2.7" thick then you can use the included screws that have "snap off" points so you can simply cut the screws down to the desired length. However, if the wall is thicker than 2.7" you can simply purchase a conventional screw from the hardware store and screw the shank kit to your wall. If the substrate is firm enough you may not even need to go all the way through the wall so a common 1-1/4" long screw may be all that is required. Specifications: Beer Line Diameter: 6.35 mm OD EVABarrier Collet and Screw Cover: 304 Grade Stainless Steel O-ring Material: Dual O-ring Silicone/EPDM combination Plastic Mounting: Polyketone (POK) Temperature Range: 14-212°F (-10-100°C) Max Pressure: 150 psi KegLand Part Number: KL32193
$21.99
-
Replacement PCO38 Tapping Head
Replacement PCO38 tapping head. This is the tapping head only. For the full tapping head assembly see KG520. Comes with PCO38 female threads for attaching to the Oxebar Mono Keg and three PCCO1881 male threaded ports for attaching ball lock caps and PRV. KegLand Part Number: KL20169
$7.69
-
Replacement Shuttles for NukaTap® Flow Control Faucet | Gen 1
Replacement flow control shuttles for the Gen 1 NukaTap FC model faucet (D1584). These pieces are only for the flow control apparatus in the faucet, not the NukaShuttle itself. A backwards compatible replacement shuttle for the Gen 2 NukaTap Flow Control Faucet is coming soon. KegLand Part Number: KL17817
$6.59
-
Filter Bag for KegLand Wood Basket Press
Mesh bag liner for the KegLand wood basket press. KegLand Part Number: KL39826
$16.49
-
Replacement RAPT Controller for BrewZilla | Gen 4 | 65L
Replacement RAPT Controller for 65L Gen 4 BrewZillas. Compatible with all Gen 4 models. This will not work with BrewZilla Gen 3.1.1 models or older. It is also not suitable for DigiBoil units. Please refer to the instruction manual on adjusting the controller between the Gen 4 units. There is a mechanical toggle switch on the back of the board that will need to be adjusted. KegLand Part Number: KL20305
$98.99
-
HIZO Cast Iron Double-Sided Skillet | Replacement Handle
Replacement HIZO Hot Plate Handle. Solid Cast Iron, branded with the HIZO Logo. It features 2 x Holes for variable hook / hanging placement. The HIZO Cast Iron Double-Sided Skillet includes two handles. This is a single replacement handle. KegLand Part Number: KL24914
$7.69
-
EVABarrier Double Wall Draft Tubing | LightShield Black | 3 mm ID x 6.35 mm OD
Easily identify gas and beverage lines with color-coded options—LightShield Black for beverages, Transparent Red for gas EVABarrier's double-walled design with a proprietary inner polymer significantly reduces oxidation and CO2 loss, keeping your beer fresher for longer The ultra-smooth, nearly impermeable inner surface of the tubing prevents bacteria and microbes from adhering, ensuring cleaner beer lines The stiff yet pliable EVA outer barrier makes the tubing kink-resistant and ideal for use with push-in fittings like Duotight and John Guest 3 mm ID size is perfect for mobile draft applications where only a short 3.2 ft. beverage line is needed Easily identify your gas and beverage lines with color-coded draft tubing. LightShield Black EVABarrier is recommended for beverage lines while using Transparent Red for your gas lines, saving you a headache when your draft lines inevitably get tangled up in your draft system. LightShield Black also works perfectly for hydroponic systems as it will block UV and discourage algae growth. If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 3 mm (5/32") ID size is perfect for mobile draft applications or home draft systems where only a short beverage line is needed. Lengths of 3.2 ft. per line are all that you'll need for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 3 mm (1/8") Outer Diameter - 6.35 mm (1/4") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. KegLand Part Number: KL42789
$28.49 - $164.99
-
Glass Rinser | Push Activated Cup Washer | Stainless Steel
Rinse and chill your glassware before every pour! Install on the countertop of your wet bar or kitchen sink and hook up to your home water supply Invert and push down your glassware to activate the spray action Excellent kitchen accessory for rinsing wine glasses, compact blenders, tumblers, and More! A push activated glass rinser can be the perfect final touch to your wet bar for the serious home beertender. Install at the edge of your sink and connect to your household's main water supply. Push down in short bursts to rinse your glass of dust, residual dish soap, and to pre-chill the glass before pouring a pint. These compact glass rinsers are capable of withstanding up to 100 psi of pressure. The 1/2" BSP threaded rod is compatible with a number of Duotight attachments. We recommend installing with PE Water Line and this 1/2" adapter. How to Use: Invert glass and empty last drips into sink Press glass onto the center of the glass rinser in short bursts If you have access to an inline carbonated water source, using bubbly water will really give your glasses a stripping clean. This device can also be used with chilled water to cool your glass down in between beverages. 4.3" H x 4.5" W KegLand Part Number: KL27649
$65.99
-
KegLand Oxebar Mono PET Keg | Replacement Graduation Sticker
Replacement graduation sticker for the Oxebar 5.2 Gallon / 20L PET keg (B286). It is white text displayed over a transparent backing sticker. Please follow the directions on the sticker on how to apply this to your Oxebar tank correctly. Oxebar Keg in photo is not included. KegLand Part Number: KL38010
$4.39
-
NukaTap® Mini Beer Faucet | Horizontal Clamp On Assembly
Perfect for mobile draft dispensing with the NukaTap Mini Beer Faucet Clamp onto a picnic bench or folding table—an ideal option for backyard cookouts or concerts in the park Makes for a great temporary shank for weekend getaways, camping, or tailgating This bracket is compatible with table or bench edges that are up to 3.5" thick. It can be adjusted to have the wing nut clamp in either direction, simply unscrew the flange piece from the threaded rod, then unscrew, then thread from the opposing side. Please note: This item does not include the Mini NukaTap or Shank pieces. It is simply the stainless steel bracket. Recommended Accessories: NukaTap Mini Faucet (D1598) Wall Mount Shank Kit w/ 6.35 mm Duotight (D1598D) Self Closing Spring (D1598A) 6.35 mm OD EVABarrier Tubing (D1723C) KegLand Part Number: KL0407
$27.49
-
Replacement Stainless Lever Collar | Intertap® | NukaTap®
Replacement lever collar for Intertap or NukaTap faucets. This beer faucet part threads onto the lever and sits above the friction bonnet. Used to help adjust your tap handle to face forward if it is oriented at an angle when fully threaded onto the faucet lever.
$3.99
-
KegLand | Gas Board for Duotight In-Line Regulators | 4 Output
Keep your draft system dialed in with this regulator gas board for Duotight In-Line Regulators. The gas board can hold up to six regulators, allowing you to monitor and adjust the pressure going to each keg. In the example photo, the high pressure from the gas cylinder is fed to the regulator on the left, and then stepped down from there with the lowest pressure line in the right-most position. The holes for wall mounting the board and the holes for mounting the regulators are pre-drilled for easy installation. Made from food-grade polypropylene plastic. Regulators, fittings, labels, and mounting hardware are not included. For a fully rigged gas board, we recommend the following parts: 4 x Inline Regulators 8 x Rigid 8mm Joiners 3 x Duotight 8mm Tee Pieces 1 x Duotight 8mm Elbow These items can be found below under You Might Also Need. KegLand Part Number: KL17701
$17.99
-
Single Sided Bead Seal | 2"
This 2" replacement gasket is intended for use with the KegLand Ball Lock Adapter Tapping Head for Sanke Kegs (KEG870). It only has the bead on one side of the gasket and the other side is flat. This gasket can also be used to directly clamp on an AlcoEngine Still Top to a compatible lid with 2" tri-clamp ferrule. It is not intended to be used as a replacement gasket for standard tri-clamp fittings. KegLand Part Number: KL99895
$2.19
-
Replacement Seal Kit | For Duotight Flow Control Ball Lock Quick Disconnect (QD)
Replacement seals and poppet for the Duotight Flow Control Ball Lock QD. KegLand Part Number: KL27212
$4.39
-
Replacement Duotight Barb for KegLand Core 360 Mini CO2 Regulator
Replacement Duotight Barb for KegLand Core 360 Mini CO2 Regulator. KegLand Part Number: KL22835
$5.49
-
Duotight Push-In Fitting - 9.5 mm (3/8 in.) x 1/4 in. BSP
This Duotight fitting with 1/4" male thread is a great option for connecting gas line to regulators and manifolds that have 1/4" FPT. Comes with seated O-ring. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL14441
$3.29
-
NukaTap® Beer Faucet Parts - Matte Black Spout
Stainless steel spout with matte black finish. Replacement for the NukaTap Stealth Bomber edition faucet. KegLand Part Number: KL24099
$6.59
-
JoinTech Quick Disconnect (QD) | Auto Shutoff | Dry Break | Female QD x 1/2" BSPT
Prevents leaks and spills when disconnected, ideal for pressurized systems Handles both hot and sub-zero fluids, from hot transfers to sub-zero glycol mixtures (-40°F to 280°F) Made with high-strength, chemically resistant polyketone plastic body, 316 stainless steel spring, and EPDM O-ring for long-lasting performance JoinTech Connectors offer a premium quick-disconnect solution for high and low-temperature beverage handling. These fittings are suitable for a wide range of applications, from hot transfers to sub-zero glycol mixtures. The connectors feature an automatic shut-off valve that prevents flow when disconnected, making them ideal for hoses used with pumps or glycol systems. Features: Durable, UV-stable black design Automatic shut-off valve Vacuum rating of 60 psi Connections: JoinTech Female QD 1/2" Male BSPT Materials: Body: High-strength, chemically resistant polyketone plastic Spring: 316 stainless steel O-ring: EPDM Specifications: Operating pressure: Vacuum to 60 psi Temperature tolerance: -40°F to 280°F (-40°C to 138°C) Flow path: 3/8" KegLand Part Number: KL50739
$9.99
-
Heavy Duty Dolly Bundle | Flat Dolly | 65L & 100L BrewZilla Gen 4
Effortlessly transport your 65L or 100L BrewZilla or 65L DigiBoil with the sturdy rolling flat dolly, designed with precut hole configurations for secure placement Includes two locking wheels to hold your brewing system in place, ideal for cleaning on sloped surfaces or ensuring stability during use Perfect for Lift-N-Lock Pulley systems, enabling seamless movement under pulleys and convenient handling of malt pipes Easily move your BrewZilla or DigiBoil around your brewing area using this rolling flat dolly. The thick reinforced plastic dolly plate comes with two precut hole configurations suitable for 65L & 100L Gen 4 BrewZillas and 65L DigiBoils, allowing the feet of your system to slot into place for easy mobility. Two locking wheels are included so you can lock your brewery in place which can be especially useful if you move the unit to a sloped driveway for cleaning. These dollies are highly recommended if you are using a Lift-N-Lock Pulley type system for your malt pipe. Easily move your system into position under your pulley, and when you're done mashing, pull the malt pipe out, wheel the BrewZilla away, and lower the malt pipe to the ground or into a cleaning tub. This dolly bundle is also the preferred option for 100L BrewZillas and 65L BrewZillas/DigiBoils that use tall bulky distillation heads. Compatible With: 65L BrewZilla Gen 4 100L BrewZilla Gen 4 65L DigiBoil Includes: Reinforced Plastic Dolly Plate 100 mm Castor Wheels (2 locking, 2 non-locking) Mounting Hardware Plate Dimensions: 25.9" Ø x 0.7" Thick (660 mm x 20 mm) BrewZilla sold separately KegLand Part Number: KB15697 NOTE: Due to the feet placement, the dolly plate is not suitable for the 35L BrewZilla or 35L DigiBoil.
$142.99
You have seen 480 out of 534 products