Keg Parts & Tools

Keg lube is incredibly beneficial for your kegging gaskets and o-rings, not only to help keep them from cracking and wearing out, but to help create a leak-proof seal as well!  We recommend that all keggers have a tube of keg lube on hand to make sure your draft system remains leak free and pouring smoothly.   Use keg lube on  lid o-rings, body connect o-rings, clover clamp fittings, and any other brewery application where you need a little extra help. Unlike most lubes, CIP Film can be removed easily with hot water for fast cleanup. FDA approved.   

Read more less

So handy you’ll swear this is the food-grade WD of your brewhouse! FDA & NSF approved food grade lubricant. Great for lubricating keg parts, especially poppet valves, relief valves, and lid o-rings. Many home brewers find it helpful in sealing those rings and gaskets that have tiny leaks. Great anti-rust film for equipment which is stored outdoors. With so many uses around your brewhouse, you’ll find yourself reaching for your bottle of Silicone Spray often!

Read more less

The KOMOS Keg Filler FOB is designed by our in-house engineers to stop the flow of beer once a keg is full. With a sleak design, it is easy to clean and extremely versatile if you wish to reconfigure it for another task.  The KOMOS Keg FIller FOB is intended as an upgrade to our Four Station Manual Keg Filler and Single Station Manual Keg Filler.  Features: Borosilicate Sight Glass Beer Thread (5/8" BSP) Easy to clean Silicone Washers Stainless Construction Food Grade Check Ball NOTE: Four Station Manual Keg Filler requires four Keg Filler FOBs

Read more less

96% reduction in oxygen ingress compared to silicone O-rings when measured in a keg! Made from a special blend of materials, these gaskets offer vastly improved oxygen barrier properties compared to Silicone or EPDM Give your beverage the absolute best protection from oxygen staling with KegLand's Low2 O-rings! The result is your beverage staying fresher for longer! Compatible with any ball lock or pin lock corny-style keg with standard lid Upgrade the storage life of your beer by replacing your standard keg lid O-ring with the new Low2 O-ring from KegLand. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Compatible with any ball lock or pin lock corny-style keg with a standard size lid. Not compatible with Megamouth Torpedo Kegs. Low2 O-rings were independently tested by GunnLab, an Australia-based plastic packaging testing laboratory. See below for a printout of the test results. KegLand Part Number: KL03063

Read more less

All the parts and seals you need to rebuild a keg in one convenient kit! Includes Low2 Keg Lid O-rings that offer superior defense from oxygen ingress compared to silicone or EPDM rings Never fear gasket failures when you go to fill your ball lock keg—this first aid kit has everything you could possibly need Comes in a convenient, well-organized tackle box tray so you never need to go searching for that tiny replacement O-ring Also includes tailpiece gaskets for keg couplers or draft shanks and nylon washers for KOMOS CO2 Regulators $100 value! Save money by not purchasing all of these parts individually The KOMOS First Aid Kit comes with all the parts needed to fully rebuild a ball lock keg and more! Don't wait for gaskets to wear down and start leaking before buying a replacement—keep this replacement part kit on hand and be ready for any situation. It's only a matter of time before keg seals fail, and when that time comes, the last thing you want to do is comb through a drawer of random gaskets for that tiny, little lifesaver. Having all your gaskets in one convenient tackle box will give you the peace of mind that you'll always be able to get your keg back in working order in no time flat. Low2 O-rings are cutting edge blend of plastic material (Synthetic M-Class and Cross-Linked Elastomers) that provide the best protection against oxygen ingress ever seen on the homebrew market. Even in a fully pressurized, sealed keg, it's possible for oxygen to dissolve in through the gap where the keg lid and O-ring form a seal. This tiny amount of oxygen ingress over time will eventually affect all beers, but is especially detrimental to highly oxygen-sensitive beers like Hazy IPAs. In addition to ball lock keg parts, tailpiece gaskets for draft shanks or keg couplers and regulator nylon washers for KOMOS CO2 Regulators are also included. The Ball Lock Keg First Aid Kit also represents an incredible value and will save you a ton of money in the long run. Buying all of the parts in this kit individually would run you upwards of $100, but you can get them all in one purchase at a fraction of that price. Includes: (1) Ball Lock Post – Gas In (1) Ball Lock Post – Bev Out (2) Keg Lid O-Ring (2) Keg Lid Pull Ring PRV (2) CO2 Regulator Nylon Washer (4) Keg Lid Foot (4) Tailpiece Gasket (6) Universal Poppet (20) Dip Tube O-Ring (10) Ball Lock Post O-Ring  

Read more less

Replacement glass tube for the KOMOS Keg Filler FOB (KEG210).

Read more less

Weighted cap design keeps the dip tube submerged, maximizing liquid draw and minimizing air intake for consistent performance Prevents hop material and other sediment from clogging your dip tube, ensuring cleaner beer transfers and samples Works seamlessly with Torpedo Keg Buoys, Kegmenter Floating Dip Tubes, and FermZilla Pressure Kits for diverse brewing setups Made with food-grade HDPE and 304 stainless steel, allowing for easy cleaning and sanitization with common brewing cleaners This handy little filter attachment can be used with the Torpedo Keg Buoy, Kegmenter Floating Dip Tube, or FermZilla Pressure Kit to keep hop material from being sucked into the silicone dip tube. This upgrade accessory is especially helpful if you like to dry hop directly in your keg while serving, or if you want to pull clean samples from your FermZilla or Kegmenter during fermentation when there's still a lot of biomatter in solution. Simply remove the metal tube from the ball float, slip the silicone tubing over the barb, then reattach the ball float to one of three clip locations. Made from HDPE and 304 stainless steel, the filter can be boiled or sanitized with the full range of cleaners that we sell. The plastic HDPE is over molded onto the stainless mesh to make a seamless finish. The end cap can easily pop off for cleaning. This updated version of the original Filter Attachment now includes a weighted cap that helps keep the end of the dip tube pointed down and submerged below the liquid surface level. KegLand Part Number: KL41485

Read more less

Enjoy a never-ending supply of soda water on tap with the Continuous Soda Carbonator Keg Lid. SodaStream units are great, but filling up those tiny 1L bottles is a pain, they're expensive to swap, and they run out quickly. Hook up your mains water supply to this Carbonator Keg Lid, compatible with any standard ball lock homebrew keg, and you'll never have to think about running out of sparkling water. Setup: Position the keg inside your fridge or kegerator (ideally below 40°F). Attach your beverage draft line to the soda water out post. Attach your gas line to the gas-in post. Set your CO2 regulator to 30-50 psi, depending on how highly carbonated you like your soda water. We highly recommend using a check valve on your CO2 line. On first use, purge the air from the headspace of the keg. Connect the mains water to the water inlet post on the lid of the keg. We recommend also using a check valve on your mains water line to prevent soda water from going back into your house mains. Depending on your mains water pressure, you may need to reduce it using the Duotight In-Line Regulator. For the Carbonator Keg Lid to work well, the mains water pressure should be 10-15 psi higher than your regulator set pressure (from Step 4). That's it. This simple unit will give you continuous soda water connected to your mains water. Please note: if you are using a CO2 regulator that uses a corny-style PRV, such as the KOMOS® regulator, you will need to swap out the standard Green PRV with the 0-100 psi Gray PRV so you can raise the pressure above 60 psi. Always check the pressure rating of your keg(s) before swapping the PRV. KegLand Part Number: KL1095

Read more less

Universal keg post o-rings can be used with both ball lock and pin lock homebrew kegs. These o-rings go on the outside of your homebrew keg posts (also referred to as body connects) which is where you connect your ball lock or pinlock quick disconnects. Comes in a convenient zip lock bag.

Read more less

Tired of fishing your picnic faucet out of the dirt or the bottom of your kegerator? This holder from Torpedo fits over most ball lock keg posts and holds your hand faucet in convenient, clean position. Made from stainless steel with the Torpedo Keg logo etched in.   Does not fit pin lock kegs.

Read more less

Replacement keg posts (body connects) for ball lock homebrew kegs. Gas In side. This piece is where ball lock quick disconnects attach to your homebrew keg. The Gas In post is identified by the small notches around the base whereas the Bev Out post is smooth. Made from stainless steel. Comes in a convenient zip lock bag.

Read more less

Replacement keg posts (body connects) for ball lock homebrew kegs. Bev Out side. This piece is where ball lock quick disconnects attach to your homebrew keg. The Bev Out post is identified by the smooth sides around the base whereas the Gas In post is notched. Made from stainless steel. Comes in a convenient zip lock bag.

Read more less

We love these keg lids as either a replacement or an upgrade to the stock lid featured on many homebrew kegs. Most homebrew kegs feature a straight, parallel bale that sits extemely close to the lid when in the closed position. So close that it can be hard to get a finger or two under the bale to open it. The arms on this lid bend outward creating a nice, easy-to-grip handle to open and close the bale. For use with Torpedo, Cornelius, and Firestone kegs. Comes with a pull-ring pressure relief valve and o-ring. PRV rated to 85 psi.

Read more less

How frustrating is it when hops cause blockage in your poppet, tap, ball valves and practically everywhere else? This really handy little filter can be used on with the Torpedo Keg Buoy or the floating dip tubes included with the Kegmenter and FermZilla Pressure Kit to prevent hops or other solids from getting sucked into the dip tube itself. The 304 stainless 80 mesh is fine enough to filter out hops and many other solids but not so fine that it gets blocked up easily. If you have a FermZilla or stainless Kegmenter this add is a must. Made from HDPE and 304 Grade stainless steel, this product can be boiled or sanitized in the full range of cleaners that we sell. The plastic HDPE is over molded onto the stainless mesh to make a seamless finish. The end cap can easily pop off for cleaning. Kegland Part Number: KL16957

Read more less

Fully carbonate your beer in under 2 days! With the Carbonating Keg Lid you can quickly carbonate beer without the risk of over carbonating like with the burst carbonation method Diffusion stone disperses CO2 directly into solution for faster gas absorption Brand new keg lid complete with o-ring and PRV The easiest way to carbonate beer. This is a Cornelius keg lid with built-in carbonation stone! Move the lid from keg to keg to carbonate as needed. Allows you to force carbonate quickly using the attached .5 micron stone with the portability of being able to move the lid from keg to keg. No more hassles of trying to attach and unattach line from the "gas in" dip tube. Simply connect your gas quick disconnect to the included fitting on the lid and allow carbonation to begin. Sometimes also called a carbonater. We constructed the lid by welding on a 1/4" barb to the underside of the lid. To that we attached 2' of 1/4" ID tubing that attaches to a .5 micron carb stone on the other end. The flexible tubing, as opposed to rigid tubing, allows the lid inserted into any cornelius style keg. The top of the lid has a "gas in" ball lock body connect welded in place that works with the KEG710 and KEG730 gas quick disconnects. Use: Beer must be stored cold at 34–40°F. Preboil the stone for 2–3 minutes before using. This assures you that your stone is sterile and any residual oils have been boiled off. Sanitize the whole keg lid before submersing into your keg filled with beer. Set your PSI on your regulator to 3–4psi and attach your gas in fitting to the body connect on the lid. Leave keg at this pressure for 1 hour. Raise your pressure 2PSI per hour until you reach 10–12psi. Leave it at 10–12psi for 24 hours. Pour a pint and test the carbonation. If you think your beer needs more CO2 leave for another 4–6 hours and have another pint. Remove carbonation lid after carbonation level is satisfactory. Return original keg lid for long term storage.

Read more less

Remove the keg spear from your sanke kegs for cleaning and maintenance For use with US-standard D-Style sanke kegs Safe and easy hand operation Easily and safely remove the valve and spear on American Sanke kegs with this Sanke Valve/Spear Removal Tool from MoreBeer! This economical tool is available for a very competitive price when you order from MoreBeer!, and it is great for anyone who needs to remove their spear on a Sanke keg for cleaning or to repair damage. Note that this tool only presses the spear down to relieve pressure on the retaining ring, you will have to remove the ring by hand.

Read more less

This gas in ball lock bulkhead assembly allows you to add a ball lock post just about anywhere. Create your own pressure vessel or attach it to one of our aluminum gas manifolds for a quick connect option. 1/4" BSP threads and locking nut. Kegland Part Number: KL03179

Read more less

A replacement pull-ring style relief valve for your favorite keg!   This is the most common relief valve. Fits most Cornelius and Firestone style kegs, along with many others. Features a long body with spring, and gray top with pull ring.    Max. pressure rating: 100 psi   Kegland Part Number: KL03070

Read more less

This bev out ball lock bulkhead assembly allows you to add a ball lock post just about anywhere. Use in conjunction with the gas in bulkhead to create your own pressure vessel. The included short dip tube can be replaced with a longer dip suitable to your needs. 1/4" BSP threads and locking nut. Kegland Part Number: KL03162

Read more less

Hang a bag, stainless hop ball, or oak strip from this tab that is welded onto the bottom of a keg lid. This is a product to use for aging your beer on oak cubes, dry hopping, adding cacao nibs - any post-keg addition of ingredients you can think of! To use, simply thread the string of your hop bag into the hole and tie off. When it is time to remove your adjunct/hops, pull the lid off of the keg and replace with a normal one. This really enables you to control the exact time your beer sits on the hops, oak, etc. and makes their removal a cinch! Kegland Part Number: KL02868

Read more less

A great way to repair your keg, even if you're not sure what type you have! This poppet works on all of the kegs that we sell, Pin or Ball lock! Poppets are pretty easy to damage or lose while cleaning your keg, and having a couple extra universal poppets on hand is a great way to make sure that you can always serve your homebrew! Compatible with our ball and pin lock replacement body connects - KEG460G, KEG470G, KEG1100, KEG1101.

Read more less

Dip tube o-rings compatible with all homebrew ball lock or pin lock kegs. Slide the o-ring onto the dip tube and then place the dip tube back in the keg. Comes in a convenient zip lock bag.  

Read more less

For the gas in side. Stainless steel construction, approximately 1.5" in length.

Read more less

Replacment foot for cornelius style keg lid for homebrewing.  This fit on the end of the swing arm latch on the keg lid. They often crack with age and need to be replaced. 

Read more less

Give your beverage the absolute best protection from oxygen staling with KegLand's Low2 O-rings! Made from a special blend of materials, these gaskets offer vastly improved oxygen barrier properties compared to Silicone or EPDM The result is your beverage staying fresher for longer! Compatible with KegLand's 20L Oxebar Mono PET Keg These seals replace the red O-ring seal inside the 20L Oxebar keg lids. What is Low2? Low2 O-rings are the new golden yellow standard of homebrew kegs brought to you by KegLand. Why? Because of their unique composition (Synthetic M-Class and Cross-Linked Elastomers), they have superior oxygen barrier properties than that of the previous silicone O-rings. This results in your beverage staying fresher for longer. The same Low2 O-ring material was independently tested on 5-gallon stainless steel kegs by GunnLab, an Australia-based plastic packaging testing laboratory. See below for a printout of the test results. KegLand Part Number: KL38003

Read more less

Remove a threaded keg spear from your Sanke kegs for cleaning and maintenance Compatible with D-Style and S-Style threaded spears Attaches directly to the 1/2" drive of an impact driver or pneumatic rattle gun This keg opening tool attaches directly to a 1/2" drive so it can be used with an impact driver or pneumatic rattle gun. This makes fitting and removing keg spears really fast and can save a ton of time when working with a high volume of kegs. Compatible with D-Style and S-Style kegs with threaded spears. There are two styles of Sanke kegs, those with a threaded-in spear and those that use a retaining ring, or circlip, to hold in the spear. This tool is designed for use with D- or S-Style Sanke kegs with threaded spears. For the more popular (in the USA) D-Style circlip-style Sanke kegs, use tool KEG860. Please Note: this tool does not remove the retaining ring. Once the keg has been depressurized, you will have to remove the ring by hand. KegLand Part Number: KL14908

Read more less

Replacement Beverage Dip Tube for the standard Torpedo Kegs.

Read more less

Replacement 3 pin body connect for pin lock kegs. Does not include poppet. 9/16-18 UNF threads.

Read more less

Replacement curved dip tube for the beer side out on Cornelius style ball lock kegs. Made from Stainless Steel. Does not include the dip tube gasket.  

Read more less

A new stainless steel, replacement body connect for the gas side of your pin lock cornelius keg keg. Features 2 pins on the side which denote it as being for gas. Does not include poppet. 9/16-18 UNF threads.

Read more less

Convert any pinlock keg over to a ball lock keg. Ideal for any homebrewer that has their home draft setups already assembled with ball lock fittings. Includes both gas and beverage body connects.

Read more less

Round EPDM O-rings for Cornelius keg lids.

Read more less

Extra-large keg lid O-ring for use with the Megamouth series ball lock Torpedo Kegs. This is an extra-large corny style keg lid gasket that will only fit Megamouth Torpedo Kegs. For standard corny keg lid, see here.

Read more less