Designed to allow the use of older FTSs pumps and heaters with new FTSs Touch controller.

Read more less

Glycol power packs for cooling fermentations of beer and wine, and also used for maintaining temperature for draft beer dispensing. These glycol packs are perfect for controlling temperature during fermentations. They can be used with cooling plates and snakes for macro bin fermentation, as well as connected to tanks via cooling jackets. Features 2300 btu Digital Thermostat Max distance of glycol "out" line - 125 Feet. Vane (Procon) with 1/3 HP Motor 115V Power 11.5 gallon bath capacity Dimensions: 27-1/2"H x 18"W x 29"D Weight: 120 pounds

Read more less

Designed for situations where your FTSs Touch and fermenter are more than 3ft away from your power supply. Can be used to extend the pump and/or power cable.

Read more less

This is a 1/6" DIN Relay Output controller with PID. It is compatible with many probe types including our PT100s. This reads Celsius only. 220V supply.  

Read more less

The FTSs Touch | Nano Jacketed Tank Upgrade kit has been designed to leverage components from our home brewing FTSs Touch line in an effort to provide a low-cost solution to pair a 1, 2, or 3.5 BBL Nano Jacketed Unitank and Nano Jacketed Brite Tanks with one of our 3/8 HP or 3/4 HP glycol chillers. This system features a custom TC thermowell adapter, along with a silicone insert to adapt the temperature probe from an FTSs Touch controller to the welded-in sleeved thermowell port on our line of Nano Jacketed Tanks.  In addition, a custom-designed low-pressure open silicone check valve is included to prevent backflow to the chiller's reservoir when glycol is not flowing.  The kit includes 1/2" NPT to 3/8" barbs to adapt the glycol ports for use with our standard FTSs Touch pump.  Since most Nano Jacketed Tanks are set up for use with a pressurized loop glycol system typically found in commercial breweries, this kit offers a Nano brewery an affordable, easy-to-setup alternative to more elaborate or expensive installations.  Everything is included to interface a single Nano Jacketed Tank between an FTSs Touch and Ss Glycol Chiller.  Cooling options for Ss Branded Glycol Chillers  FTSs Touch | Jacketed Tank Kit — Designed to be paired with our line of Ss Glycol Chillers.  Cooling options for Pressurized Glycol Loops on Commercial Chillers  FTSs Pro Touch (+ FTSs Pro Touch Solenoid Valve)  — Designed to be paired with pressurized-loop (Non-Ss Brewtech) commercial glycol systems. Not recommended for 5bbl & Larger Tanks Includes: (4) FTSs hose clamp for 3/8" barbs (1) Hose barb - 3/8" to 1/2" MPT (1) Silicone thermowell cover (1) 1.5" TC sleeved thermowell adapter (1) FTSs harness extension 3 ft (1) Silicone check valve Works with 1, 2, and 3.5 bbl Nano Jacketed Tanks Not required for Unitank 2.0  

Read more less

The Chilling Coil kit can be used to update the 14 gal Brew Buckets for temperature control. Then you can add an FTSs Touch kit for use with the Ss Glycol Chiller. Features: Thick 5 mm zippered neoprene jacket Immersion chiller coil mounted to 6" TC cap Cap | 3” TC with ½” Blow-Off 3/8" hose barbs on the chiller coil Included hose clamps (for chiller coil), TC Clamps, TC Gaskets Kit not compatible with Brite Tanks, Chronical Series, or Unitanks. Specs: Assembled Dimensions: 30"H x 16.5"W x 16.5"D (on Bucket) Assembled Weight: 30lbs / 13.5kgs (on Bucket)

Read more less

This is a 1/6" DIN Relay Output controller with PID. It is compatible with many probe types including our PT100s. 220V supply.  

Read more less

Tired of your digital controller laying awkwardly in the way? Now there is a solution - hang it up! Our hanger screws into a vertical surface and allows you to hang the controller. The hanger bracket features two posts that fit the mounting holes that are a part of the Ranco Controller. This allows you to hang the unit when in use and the remove the unit when you want to clean. This can be handy when you are cleaning with water and could potentially get the controllers wet. Use it to hang your controller on a refrigerator, fermenter stand, brew system, or whatever else you have dreamed up. This is a custom piece made by MoreBeer!

Read more less

Replacement adjustable foot for the RAPT Fermentation Chamber. Single foot, not a set of 4. KegLand Part Number: KL26789

Read more less

This plastic insert is located in the top panel of the RAPT fermentation chamber. These can be removed or replaced to route gas line from a mounted Duotight regulator. KegLand Part Number: KL26444

Read more less

Replacement Top Lid Cover for RAPT Fermentation Chamber. KegLand Part Number: KL26420

Read more less

This water drip tray is a replacement part if you have damaged your drip tray or you simply want a new one. Makes for easy cleanup of any spills or condensation formed during the operation of your RAPT Fermentation Chamber KegLand Part Number: KL26284

Read more less

Replacement Base Tray Cover for RAPT Fermentation Chamber. KegLand Part Number: KL26277

Read more less

Replacement LCD control panel for the RAPT Fermentation Chamber. This Replacement LCD screen has been flashed with the firmware for the RAPT Temperature Controller. It is not compatible with the RAPT Temperature Controller. KegLand Part Number: KL17091

Read more less

Replacement Main Circuit Board for RAPT Fermentation Chamber KegLand Part Number: KL17084

Read more less

Replacement Foam Filled Door for RAPT Fermentation Chamber. This is a direct replacement for the standard door included in the RAPT. Brushed stainless steel with PU foam insulation. KegLand Part Number: KL15837

Read more less

This is a 1/6" DIN Relay Output controller with PID. It is compatible with many probe types including our PT100s.

Read more less