Designed to be used with a recessed countertop drip tray, but you can add this bulkhead to virtually any drip tray you'd like to gravity feed spills into a bucket or drain.
KegLand Part Number: KL12577
Designed specifically for mounting the NukaTap Mini Beer Faucet on any kegerator, keezer, cold room wall, or other flat surface
Connect beer line directly to the faucet, reducing the amount of temperature loss to a standard draft shank
No spinning faucets. Your tap will remain in a fixed orientation once locked into the collet
Easy installation. No need to drill a large hole through your fridge to accommodate a standard 5/8" draft shank
Use with 8 mm OD EVABarrier draft tubing
Note: Faucet Sold Separately
This shank kit is specifically designed to suit the NukaTap Mini Beer Faucet and will allow you to connect the NukaTap Mini to a cooler box, kegerator, keg fridge, cold room wall or any other flat surface.
This wall mount shank kit is for use with 8 mm OD EVABarrier. For the shank kit for use with 6.35 mm OD EVABarrier, see here.
New Innovative Shank Design
Unlike other shank kits, this kit doesn't use a bulky 5/8" threaded shank. The issue with a standard draft shank is that acts as a heat sink, and due to the fact that most shanks sit inside an insulated wall, this results in a substantial amount of warm beer coming out of the tap before cold beer starts flowing. This results in substantial "first pour foam" effect which wastes beer, can result in sour beer, and ultimately negatively effects the quality of the beverages being served. This new design has the beer line feed all the way directly up to the back of the faucet, greatly reducing the volume of non-refrigerated beer.
No Spinning Shanks
If you have ever installed a traditional 5/8" long shank, you will know how frustrating it is when you use the faucet and it starts rotating. This new design of shank alternative uses three screws that lock the tap into a fixed position and prevents the taps from rotating. If you loosen the 1/2" stainless tap collet you can still have the flexibility to rotate the faucet to any orientation, but once the collet is tight, interlocking teeth on this shank kit and the NukaTap Mini will hold the tap permanently in the correct orientation.
Easy Installation
Another advantage compared to standard shanks is that this kit doesn't require you to drill a large 3/4"-1" hole through the wall. As no shank is required, only a hole large enough to accommodate the beer line is required. As a result, an 8mm (5/16") conventional drill bit is all that is necessary for installation. However, if you are concerned about the small amount of beer sitting in the draft line inside the wall not being refrigerated, you can also shell out a larger diameter of foam on the inside of the wall to allow cold air to circulate around the beer line thus reducing the non-refrigerated beer in the line even more. If you wanted to do this the Step Drill Bit is the best tool for the job.
Any Wall Thickness
Other shank kits will require you to purchase a specific length shank for a specific wall thickness. This new shank alternative will fit any wall thickness. If you have wall thicknesses that are less than 2.7" thick then you can use the included screws that have "snap off" points so you can simply cut the screws down to the desired length. However, if the wall is thicker than 2.7" you can simply purchase a conventional screw from the hardware store and screw the shank kit to your wall. If the substrate is firm enough you may not even need to go all the way through the wall so a common 1-1/4" long screw may be all that is required.
Specifications:
Beer Line Diameter: 8 mm OD EVABarrier
Collet and Screw Cover: 304 Grade Stainless Steel
O-ring Material: Dual O-ring Silicone/EPDM combination
Plastic Mounting: Polyketone (POK)
Temperature Range: 14-212°F (-10-100°C)
Max Pressure: 150 psi
KegLand Part Number: KL32186
Keep your draft faucet in perfect working order.
Replace your old friction washer to keep your faucet lever moving properly
This is the second washer of a two part set (D1200D)
With this washer you can renew a worn-out part on your well-used draft faucet. This replacement part is the second washer of a two part set that is used to control motion of lever.
The coupling nut is what attaches your beer faucet to the shank. This black coupling nut pairs perfectly with the NukaTap Stealth Bomber faucet without the need to purchase a whole new shank. Or add some flair to your existing setup by mixing and matching black and stainless steel.
Handle this part with care, as scratches will show up more clearly compared to the stainless versions.
KegLand Part Number: KL20275
For the do-it-yourself person, this is the piece that you see at the bottom of most handles, you must also get the D1298B if you want to screw it into a wood tap handle. (5/16" top threads and 3/8" bottom threads)
Replacement flow control shuttles for the Gen 1 NukaTap FC model faucet (D1584). These pieces are only for the flow control apparatus in the faucet, not the NukaShuttle itself.
A backwards compatible replacement shuttle for the Gen 2 NukaTap Flow Control Faucet is coming soon.
KegLand Part Number: KL17817
5/16" Tailpiece Elbow that is used with a 1" tailpiece hex nut (D1740 / D1741). Fits on couplers and shanks. Requires 1-5/8" clearance above the coupler or behind the shank. Made from stainless steel.
ID - 1/4"
OD - 5/16"
Replacement flow control shuttles for the Gen 2 NukaTap Flow Control faucet. These pieces are only for the flow control apparatus in the faucet, not the NukaShuttle itself.
These pieces are backwards compatible with the Gen 1 NukaTap Flow Control model, replacing part numbers 11 and 12 in the diagram image above.
KegLand Part Number: KL17817
The classy way to say "Don't you dare drink my beer!" Do you have a draft system and live with either teenage kids or thirsty roomates? This can potentially be a beer draining arrangement. When you leave for the weekend, stop the flow with a faucet lock. A quick easy locking system that attaches directly to the faucet.
Specifically designed for Perlick 630 series draft faucets. For standard beer faucets, please see D1274.
Keep potential “beer-samplers” and kids out of your draft system with this Beer Faucet Lock.
Give yourself some peace-of-mind, knowing that your draft system is locked and your beer is safe. If you're a serious homebrewer this thought has crossed your mind: the thought of someone walking by and pulling on the tap handle, letting beer run out. Be it friends or your kids, you want your system to be secure. This quick and easy Beer Faucet Lock attaches directly to the faucet. It gives a solid squeeze on the handle, locking it into place, without fear of damaging it. This one-of-a-kind lock is something you’ll be glad you own.
Please note - this lock will not work with Perlick 650SS, 630SS or Intertap faucets
Instant and infinite sparkling water at your fingertips whenever you want it!
Benchy connects to your household's water supply, chills, carbonates, and delivers on demand
Serve up to 8 gallons of chilled, carbonated water per hour
Pair with draft faucets and place it on your counter, or install it under the counter and plumb it to a mounted water faucet
See below for detailed installation video
Benchy Sparkling is the answer for instant chilled and carbonated water on demand. Simply connect your household water supply and CO2 Cylinder to the unit and receive unlimited sparkling and chilled water from the draft faucets. The chiller is highly efficient with very little power draw while idle and has enough cooling capacity to serve up to 8 gallons of sparkling water per hour. This unit comes without shanks or draft faucets, as it can be used as a countertop unit or installed under your counter and routed to a faucet you install on your counter or kitchen sink. If you plan to use it as a countertop unit, we highly recommend NukaTap Flow Control Faucets.
Easy Installation:
Plug the Benchy into the wall
Fill internal water tank
Connect household water supply
Connect CO2 Cylinder
Pour chilled sparking water.
It's that simple and you can be enjoying chilled sparkling water in under 1 hour with this setup and barely any time at all to cool down.
Ensure that the unit is installed and operated according to the instruction manual which can be found below.
Fully Adjustable
The Benchy Sparkling has an integrated digital temp controller so you can control the temperature from 0.5-10°C (33-50°F). You can also vary the carbonation level from 0.5 volumes to over 5 volumes for super bubbly water.
Cooling Performance
The Benchy Sparkling is able to chill about 5 to 8 gallons of sparkling water per hour (based on ambient water and air temperature of 68°F). To further increase the capacity of this unit, you can pre-chill the water from your household supply line either by a holding tank (ball lock keg) in the fridge or a DraftMaster Chiller. If you pre-chill the water you can more than double the output of the Benchy Sparkling. The reservoir temperature on the Benchy should never be set below 2°C (35°F) as you will run the risk of freezing the water inside the carbonation keg.
Specifications:
110V
Refrigerant: r600a (80 grams)
Cooling Power: 600 watts
Power Consumption: 155 watts (idle power consumption less than 5 watts)
Capacity: approximately 6.6 gal/hour (based on 68°F ambient temperature)
Input Gas: CO2 @ 29-50 psi (Requires 8mm (5/16") OD tubing)
Input Water: Must be 15 psi higher than gas pressure (Requires 6.35mm (1/4") OD tubing)
Sparkling/Chilled Water Out: Requires 8mm (5/16") OD tubing
Dimensions: 18.3" H x 11.4" W x 20.5" D (Excluding sight glass that can be removed)
Recommended Accessories:
CO2 Gas Cylinder
CO2 Regulator
EVABarrier 4mm x 8mm Tubing
PE Water Line Tubing
6.35mm Duotight In-Line Regulator (0-150 psi)
Duotight Reducer - 8mm x 6.35mm
8mm Duotight Check Valve
Diverter Valve (check water line connection for the size you'll need)
Countertop Installation Recommended Accessories:
(2) Short Shanks & Hex Nuts
(2) Duotight Adapters - Beer Thread x 8mm
(2) NukaTap FC Faucets & Self Closing Springs
(2) Tap Handles (of your choice)
Tube Cutter
Faucet & Shank Wrench
KegLand Part Number: KL20688
If your Taprite Regulator is drifting or losing pressure, why not try repairing it rather than replacing? Over time the internal diaphragm can wear out resulting in drifting pressure or a slow leak through the regulator body Refurb your unit with this Regulator Rebuild Kit and return your Taprite regulator to it’s lost glory.
Works with Taprite CO2 or N2 regulators. Not intended for other regulators.
Taprite Part Number: 7740-19-SP
This stainless steel drip tray is perfect for the KOMOS Double-Wide kegerator and home bar countertops. At 29.5" in length, this drip tray can comfortably cover up to 8 draft faucets. The grill is removable for easy cleaning.
Features:
Removable grill
Made from stainless steel
29.5" L x 6.7" W x 0.9" D
Keep the top of your kegerator clean with this stainless steel countertop-style drip tray. Perfect for placing underneath a draft tower or 2 faucets mounted side-by-side. Removable grill for easy cleaning. Features 5 pressed locations for drilling through and plumbing the drip tray for draining.
Features:
Removable grill
Made from stainless steel
11.8" L x 6.7" W x 0.6" D
Kegland Part number: KL13161
Keep your draft faucet in perfect working order.
Replace your old ball washer to keep your faucet lever moving properly
This is the first washer of a two part set (D1200C)
With this washer you can renew a worn-out part on your well-used draft faucet. This replacement part is the first washer of a two part set that is used to control motion of lever.
This is a large rubber washer for use on beer shanks and jockey box shanks. These will help to create a seal around the hole that your faucet shank goes through.
If you have a SodaStream CO2 cylinder then you can use this adapter to attach a CO2 regulator to it and avoid having to use those large 5 lb. CO2 tanks.
This adapter also has a side adjustment pin valve into the SodaStream bottle that enables the pin valve to be engaged once the cylinder, adaptor, and regulator have all been screwed together. This ensures that the gas supply from the bottle to the regulator can be engaged and disengaged while everything is screwed in place.
The adapter is incompatible with our Taprite brand regulators.
These stainless short shanks are typically used for attaching faucets to a KOMOS® Cobra style draft tower. The threaded section measures 25mm in length (0.98").
This beverage line jumper connects to the bev output on a ball lock homebrew keg and to the back of a pass through shank on a jockey box. This is a direct replacement to the beverage jumper that comes with the KOMOS Jockey Box Connection Kits (D1761 & D1763).
Specifications:
5 ft of 5/16" ID Beverage Tubing
5/16" Tailpiece Elbow
Flared Ball Lock Bev Out
If your home draft system is a mix of ball lock kegs and European sanke kegs, having a coupler with ball lock adapters is a huge plus. This allows you to have all your draft lines ending in a ball lock quick disconnect, making it quick and easy to swap lines from sanke keg to ball lock.
Note that the gas-in adapter has a small line cut into the body of the adapter where the bev-out adapter is smooth.
The check valves will need to be installed before first use. The silicone check valve is inserted on the side gas-in port and the check ball and ball retainer are inserted on the top bev-out port.
S-style sanke coupler
Stainless body
Stainless probe
PRV rated to 4.5 BAR (65 psi)
This 6 in. chrome shank comes with a back nut, plastic collar, and a welded 1/4" nipple. Requires a 1" hole saw for installation.
Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. This is a Chrome Plated Brass unit.
Dimensions:
6-1/4" - Total Length (Tip to Tip)
5-1/2" - Shank Length (Without Nut & Nipple)
4-1/8" - Thread Length
5-1/4" - Pass Through Length
Perfect for summertime parties, the low-profile design makes this pump easy to use, store, and transport. At the beach, the park, or in the backyard, the Shorty will provide you with great beer keg after keg. For D style kegs.
Also known as a keg coupler, coupling, or adapter.
Yeast require oxygen for growth, make sure you always have some available to oxygenate your wort prior to pitching!
This 20 cubic foot O2 cylinder is good for about 500 batches of beer.
Hate having your disposable oxygen tank run out right before you were about to pitch your yeast? Or just tired of running through disposable tanks in general? Consider stepping up to a refillable oxygen cylinder. Whether you brew big batches or brew frequently, a refillable oxygen tank is a great way to save time and money.
The tank needs to be hydrotested every 10 years and is easily and affordably filled at any participating welding gas company.
Specs:
Cylinder: 20 cu ft
Material: Steel Cylinder – Standard Valve
Capacity: 20 cu ft (566 Liters)
Service Pressure: 2015 PSI / 139 Bar
Test Pressure: 3360 PSI
DOT- and TC- Approved
Valve Type: CGA540
Dimensions:
Diameter: 5.2" (132 mm)
Height: 14.8" (376 mm)
Empty Weight: 14.1 lb
You can use pass through shanks for beer entry through the back side of a cooler. Drill a 1" hole through the cooler, insert the shank, and use the two attached nuts to tighten up on the cooler. You will need nuts and nipples of the size line you are working with as well as hose clamps. We do not use pass through shanks in our boxes because we drill a hole that is same size as the line so we can pull it back in when we are traveling. However there might be instances where they would be appropriate. Pass through shanks can also be used to put through the side of a refrigerator to pass a gas line through.
Installation Note: On a fridge there are generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling.
This is a stainless steel shank with chrome plated brass hex nuts.
Dimensions:
3" - Shank Length
3" - Thread Length
1-7/8" - Pass Through Length
Max length with hex nuts at either end
Does not account for nuts/nipples you may install
Male Beer Thread (5/8" BSP)
Serve beer on tap at home! A quality CO2 tank is a core component to any home draft system.
Made from high-quality aluminum that will never rust like steel tanks
Dispense up to 50 x five-gallon kegs of homebrew
CGA320 valve pairs with standard US-style CO2 gas regulators
KOMOS® offers a full suite of first-rate draft products and draft fittings—from kegs to faucets and everything in between!
This size is large enough for commerical applications—it should last you a while on your home draft system
Brand new aluminum 25 lb CO2 tank made from high strength aluminum alloy and high quality CGA320 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It’s called a 25 lb tank because it holds 25 lbs of compressed (liquified) CO2. 25 lbs of CO2 is enough to dispense about 50x 5-gallon kegs of homebrew.
Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder.
Tanks should always be stored in an upright position.
Features:
Made from corrosion resistant, engineered Aluminum
Brushed finish
Thick, durable cylinder walls
32.5" T x 8 Ø
DOT approved
New high quality CGA-320 valve
Light weight compared to steel tanks
This tailpiece is a replacement for the gas-in barb that comes mounted on our D1505 Sanke Tap. It will not work as a 5/16" beer line connection due to the lip on the back side of the fitting.
Tailpieces are fittings which connect beer and gas tubing to the different parts of a draft system. One side of the tailpiece features a barb to connect the tubing to, and the other side is held against the tap or faucet shank with collar nut.
Tailpieces are available in a range of barb sizes to fit up to your tubing size.
Foam on Beer Detectors, or FOBs, are commonly used in commercial draft systems as a way to eliminate product waste and increase profits. When a keg completely empties and foam passes into the FOB it will shut off flow and in doing so keep the draft line completely full of beer until a new keg is tapped. This means you can hook a fresh keg and continue pouring without foaming issues, preventing you from wasting beer that is otherwise needed to refill the line and purge the system.
The FOB can also be used in homebrewing applications as a convenient way to purge kegs of oxygen. Check out video below where our friend Kee repurposes the FOB to move sanitizer from one keg to another and purge the keg of oxygen in the process.
Comes with 3/8" Duotight compatible barbs at the inlet and outlet, allowing you to easily hook up EVABarrier tubing with either a 9.5 mm joiner or 9.5 mm to 8 mm reducer (DUO113 / DUO105). If not using EVABarrier, simply clamp the line directly onto the barb.
Setup and Use:
Attach beverage line from outlet of keg coupler to straight inlet of FOB.
Attach beverage line from elbow outlet of FOB to faucet shank.
Connect fresh keg and push down purge button until the chamber fills with beer.
Push bottom knob in to lift float then pull out for normal operation.
Kegland Part number: KL00802
Keep your draft faucet in perfect working order!
If the lever gets stuck or is unused for a long time, it can break
Replace it to keep using your favorite tap handle and keep the beer flowing!
With this brass lever you can renew a worn-out part on your well-used draft faucet. This is the actual lever that opens and closes the faucet, and where the tap handle is threaded on. These levers can break if a faucet is left alone for too long and the lever gets stuck.
Faucet shanks allow you to mount a draft faucet just about anywhere. Typically installed in the door or wooden collar of of a converted fridge/freezer, the front of a cooler, or even in your house’s wall when constructing that ultimate home bar!
Once installed your beer line connects to the back of the shank and a faucet attaches to the front. Shanks are available in a range of sizes to accommodate mounting on materials of varying thicknesses.
The shank’s listed size refers to the total length of threaded pipe. Approximately 1 1/8” are needed to account for the thickness of the finishing collar on the front and the space for the locknut on the back. Please take this into account when sizing the shank for your project.
Features a welded 3/16” barb and includes a glossy black plastic collar and locknut. Requires a 1” hole for installation.
Dimensions:
6-1/4" - Total Length (Tip to Tip)
5-1/2" - Shank Length (Without Nipple)
4-1/8" - Thread Length
5-1/4" - Pass Through Length
The KOMOS Cobra draft tower has a beautiful polished finish and features a built-in glycol loop for chilling. These towers are a gorgeous option for your tap room or home bar. The signature condensation on a glycol chilled draft tower will surely have your patrons thirsting for a pint! Of course, using the glycol loop is optional and isn't required to appreciate the striking design of the Cobra tower.
The towers come with female beer thread sockets and do not include shanks or faucets. We recommend the stainless Cobra Tower Shank and stainless Intertap forward-sealing faucets. When installing the shanks you will also need a tailpiece gasket to create a good seal.
For chilling the tower we highly recommend the KOMOS DraftMaster glycol chiller. This unit features a built-in submersible pump intended for pushing glycol or ice water through the Cobra tower's cooling loop. The pump can be turned on independently to circulate cooling solution constantly while you're serving from the tower, and then turned off when not in use. The DraftMaster also has 4 built-in draft coils that sit in the glycol reservoir, so you can serve from kegs at room temperature by passing the beer through the chiller on its way to your faucet.
Features:
Dual Tap
Glycol Loop
8mm OD stainless steel lines
Female Beer Thread (5/8" BSP) sockets for attaching shanks
Made from cast brass with chrome plating
Faucets and faucet shanks not included
Dimesnions:
Height: 14.16 inches from mounting plate
Width: 4.16 inches
1 inch OD
Please note: the beverage lines and glycol loop do not come marked. To identify them, blow air into the lines. If the air comes out of another line, that's the glycol loop. If the air comes out at the shank socket, it's a beverage line.
