If you're looking for a deal on homebrewing equipment you came to the right place! Below is all of our Homebrewing Equipment currently marked down for clearance. Take advantage of our industry leading customer service and fast & free shipping!
Replacement 3mm thick gasket for the 35L Distillation Lid. Note: The 3mm gasket works well with Gen 3 and older BrewZillas and Gen 1 DigiBoils. If you have a newer model, we recommend the 6mm Gasket for a better seal. To improve the seal further, we highly recommend using the Adjustable Lid Clamps with the Distillation Lid if your unit does not have them. KegLand Part Number: KL03490
$8.79 $4.99
The KOMOS draft line kit includes lengths of EVABarrier draft tubing, the same tubing used in all KOMOS kegerators. Each kit includes beer line and gas line, and Duotight tee fittings to split your gas line (excluding single tap kit). See below for recommended Duotight fittings. EVABarrier tubing is a high-quality double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! The outer barrier gives the tubing a nice stiffness that makes it extremely kink resistant and perfect for use with push-in fittings. The inner wall is an excellent gas barrier, keeping oxygen out and CO2 in. The internal surface of the tubing is extremely smooth, making it difficult for bacteria and microbes to cling to. Kits Include: Beverage line Measures 4mm ID x 8mm OD 1 x 1.7m length of line per tap Gas line Measures 5mm ID x 8mm OD 1 x line of varying length depending on number of taps (2, 2.5, or 3m) 4 Tap kit includes uncut rolls of bev & gas line We recommend cutting bev lines to 5.5-6.5 ft. lengths Gas lines can be cut to whatever length best suits your needs Duotight tee fittings to split gas line (for 2-Tap and higher)
$4.99 - $6.99
$0.99 $0.79
This product holds 1/2" racking tube to a Carboy or Pail.
$2.99 $1.99
Please note: This stopper was designed for use with the BrewBuilt CoolStix which has been discontinued. Two of the holes are for an airlock and thermowell, but the third 1/2" hole was intended for the CoolStix and you will need to plug it or utilize it how you see fit. This #10 3-hole silicone stopper is used alongside the BrewBuilt CoolStix for Carboys. The holes are for a 1/2" CoolStix, an airlock, and a thermowell. The holes measure 0.500", 0.413", & 0.375" Compatible with Fermonsters and our Plastic PET Carboys listed below under "You Might Also Need".
$8.79 $1.99
Replacement lid knob for the 35L BrewZilla (Gen 3). Kegland Part number: KL07283
$8.79 $7.99
#2 natural latex rubber stopper - solid. Top diameter 20 mm, bottom diameter 16 mm, length 25 mm. 67 stoppers per pound.
$0.79 $0.50
Replacement tube only for BrewZilla Polycarbonate Sight Glass. Fittings are not included. 15.25" long. 5/8" OD
$7.69 $4.99
A good sized Scoop, perfect for grain, other ingredients, or chemicals.
$6.99 $5.99
Brew System Cover, perfect for keeping the dust and debris off your brewing system when it is packed away in storage! Compatible with both The Grainfather All In One Brewing System, as well as the New Brewer's Edge Mash and Boil!
$23.99 $14.99
Please note: This hood was designed for use with the BrewBuilt CoolStix which has been discontinued. Two of the holes are for an airlock and thermowell, but the third 1/2" hole was intended for the CoolStix and you will need to plug it or utilize it how you see fit. This silicone 3-hole carboy hood is used alongside the BrewBuilt CoolStix. The holes are for a 1/2" CoolStix, an airlock and a carboy thermowell. The holes measure 0.500", 0.413", & 0.375" Compatible with smooth neck carboys only. Does not fit Italian threaded neck carboys.
$8.79 $1.99
Kegerator draft line kit for a triple tap tower. Kit Includes: Beverage line Measures 4mm ID x 8mm OD (5/32" x 5/16") 1 x 5.5' length per tap Gas line Measures 5mm ID x 8mm OD (13/64" x 5/16") 1 x 10' length Barbed tee fittings for splitting gas line Hose clamps
$21.99 $14.99
Stainless steel Tri-Clamp reducer with 3" T.C. and 1.5" T.C. connections.
$32.99 $24.99
Kegerator draft line kit for a double tap tower. Kit Includes: Beverage line Measures 4mm ID x 8mm OD (5/32" x 5/16") 1 x 5.5' length per tap Gas line Measures 5mm ID x 8mm OD (13/64" x 5/16") 1 x 8' length Barbed tee fitting for splitting gas line Hose clamps
$16.49 $11.24
Royal Blue Thermoseal Hoods. Plastic heat shrink hoods are the choice of the wine industry which is moving from using lead capsules. Use a hot air dryer, air gun, or steam to shrink for an easy and effective way to seal your wine bottle.
$4.50 - $149.99
Made with durable borosilicate 3.3 glass, these Erlenmeyer flasks are suitable for most applications. They feature a heavy-duty beaded rim to help prevent breakage and have easy-to-read graduations. Able to withstand temperatures of -50 to 550 °C (-58 to 1022 °F), they are autoclavable for sterilization. In the lab world, these flasks are known as "Student Grade". Student grade is not the highest grade flasks and will have minor defects. Please note this 125mL flask has a narrow neck compared to our Y402 unit and will not accept a #5 stopper. This unit will need a #3 stopper. Specs: Material: Borosilicate Glass Capacity (mL): 125 Capacity (oz): 4 Min Graduation (mL): 50 Max Graduation (mL): 125 Graduation Interval (mL): 20 Overall Height (in): 4 59/64 Overall Height (cm): 12.5 Top Outside Diameter (mm): 22 Autoclavable: Yes Base Diameter (cm): 7.2 Inside Rim Diameter (mm): 20
$9.99 $5.99
This is a Stainless Steel one way Check Valve. It has 2" T.C. Fittings on either side, and releases pressure at ~1 p.s.i. Can be used to inhibit a siphon in certain applications, or to vent gas pressure in a tank.
$109.99 $49.99
This adapter piece enables legacy Torpedo Mini CO2 Regulators (KEG965A) to be compatible with 74g CO2 cartridges that have a small unthreaded gap at the top of the neck—cartridges similar to KEG969. This piece now comes standard on the updated Torpedo Mini CO2 Regulator and is a direct replacement part for KEG965B.
$5.49 $2.99
The H205 55,000 burners come with 90 degree angle jets. These work great with a flexible gas line hook up. However, in some hard piped applications a straight jet is needed, so we made one. Threads directly into burner. We use them on our systems
$3.29 $1.99
Easily connect multiple BrewBuilt AfterBurners together to create your very own brewing stand. Predrilled holes on every BrewBuilt Burner allow for easily assembly. Includes stainless straps for backside connection along wtih a laser cut plate for the front of the stand. Front plate also includes predrilled holes for mounting a pump bracket. 8 bolt assemblies are included for a rocksolid connection. This beefy mounting plate is made in the US out of thick, 12 gauge 304 Stainless Steel.
$79.99 $59.99
Add these super-duty casters directly to your BrewBuilt AfterBurner and save your back. Your BrewBuilt Burner comes with pre-drilled holes making installation super easy. Includes two casters, two stainless steel mounting brackets, and four bolt packages. When also used with the optional BrewBuilt Handle you will be able to easily wheel your burner into place.
$34.99 $24.99
Neoprene jacket for legacy Ss Chronical 14 gallon fermenters. This jacket is not compatible with the Chronical 2.0.
$60.00 $49.99
Brass - 1/2'' Compression x 1/2'' FPT
$2.99 $1.99
The tool is utilized for electrode removal on select Hanna testers. With a simple twist of the removal tool, the tester electrode can safely and easily be removed and replaced with a new one. pH and conductivity (EC) electrodes naturally fatigue over time, requiring replacement to ensure measurements are obtained quickly and accurately.
$9.99 $6.99
This stainless steel bucket is perfect for stainless conical fermenters. Drill a small screw into one of the fermenter's legs and route your tubing into the bucket. Ideal for conicals with caster attachments—no need to pick up your water/sanitizer vessel if you need to move the conical during fermentation. Made from durable, easy-to-clean stainless steel.
$24.99 $19.99
Replacement recirculation rod for Gen 4 BrewZillas. Includes ball valve and female camlock.
$27.49 $17.99
This SS handle option is a great upgrade to get your AfterBurner moving! Combine this with the Caster Package and your AfterBurner will be an easily cartable brewery. This handle is designed specifically for the Modular AfterBurner Packages, and has drilled holes for easy attaching. Comes with Stainless Steel Handle and Bolt connection packages. Please note that this handle is designed specifically for the BrewBuilt AfterBurner.
$29.99 $19.99
Replacement stainless steel frame for the 35 L Fermentasaurus.
$32.99 $19.99
This tri-clamp extension tube features 4" tri-clamp connections at both ends and is made from high-quality stainless steel. Extension tubes (or spools) are an easy way to extend the length of any T.C. fitting. 4" tri-clamp 2" long Made from 304 stainless steel
$79.99 $39.99
Pump Cover for the Grainfather G30 All Grain Brewing System.
$14.99 $11.99
4" TC Ferrule is used to weld in a TC connection anywhere you need one! 304 Stainless Steel
$15.49 $10.99
Stainless pressure relief valve. Rated to 1 BAR / 15 psi. Non-threaded. For welding in place only.
$9.89 $4.99
This is a 1/6" DIN Relay Output controller with PID. It is compatible with many probe types including our PT100s. This reads Celsius only. 220V supply.
$27.49 $9.99
Replacement pre-drilled FTSs lid. Included with the the Ss BrewTech FTSs chilling system for the 1/2 bbl Chronical. Lid only. This does not include the other FTSs components.
$77.99 $29.99
$4.99 $3.99
Imported grape picking bucket from Italy with a sturdy handle. Is more maneuverable than a 5 gallon bucket when trying to get in and around grapevines and is also much easier to carry. They do a lot of handpicking in Italy... they have it figured out! *Basket color may vary
$25.49 $18.99
