Beer Brewing Equipment & Supplies

Keep an eye on your temps with the BrewBuilt tri-clamp thermometer. Perfect for stainless conical fermenters or T.C. kettles. The 3" diameter dial face is easy to read and scaled in °F and °C. The 6" probe length provides the thermometer with plenty of exposure for more accurate readings. 3" dial face 6" probe 1.5" T.C. Reads in °F and °C  

Read more less

Plumber's tape, or PTFE thread seal tape, is used to connect NPT (national pipe thread) style threads. Use three wraps for brass and six wraps for stainless steel. 1/2'' wide x 520'' long roll.

Read more less

O Ring for Beer & Gas Line QD (for H550A)

Read more less

Clean up your beer and give it that sparkling clarity you see in commercial brews. Filtering removes yeast and dry-hop sediment, both of which can impart off flavors. It's also a great way to give your beer that extra edge in competition. This two-pack of filter pads are for use with our FIL45 series of plate filters. Polish pads will provide between 1-2 Micron filtration.

Read more less

If you've been looking to step up from fermenting in plastic buckets or carboys, this is an excellent choice for your next fermenter. Stainless steel is a much better option than glass or plastic, as it is extremely easy to clean and virtually lasts forever. There's also much less chance of contamination as stainless doesn't scratch like plastic. Over time, you'll get scratches in plastic fermenters from normal wear and tear, creating microscopic havens for bacteria. Meanwhile, glass carboys are always at risk of breaking which is something you will never have to worry about with stainless steel. The Bucket Buddy is a great value if you're looking for a stainless steel fermenter with built-in heating control. If you live in a cold climate, ale fermentations may be a seasonal affair, as cold ambient temperatures can easily drive down the temperature of your wort below your yeast's optimal fermentation temp range. The Bucket Buddy offers a simple solution with an integrated heating element and digital temperature control. Program your fermentation temperature and if the temp drops below your set point the unit will gently heat your wort from the bottom up via the concealed element located in the base. For cooling, you can place the fermenter in a dedicated refrigerator or drill into the lid to install a Temp Twister Cooling Coil. A temperature controller probe can then be taped to the side of the fermenter to control your cooling source, or you can drill another spot in the lid for a thermowell. Another advantage over carboys and plastic buckets is the domed base inside the fermenter which is great for yeast flocculation when fermentation is complete. The included racking arm will make it easy to transfer out every last drop of beer while leaving the yeast cake undisturbed. The entire racking arm and ball valve assembly is weldless, which means you can remove the assembly to clean and sanitize it between batches. You can even boil the assembly for added assurance that it's been sterilized. To help maintain a steady temperature and cut down on power consumption, the Bucket Buddy pairs well with either the BrewZilla Neoprene Jacket or the FermZilla Insulating Jacket. This unit comes standard with silicone tubing to transfer from the ball valve to your bottles or cans, as well as a stopper and airlock for the domed lid. Specifications: 304 stainless steel construction 9.25 gallon total capacity Digital temperature control 110V / 36W power Stainless steel outlet valve with rotating racking arm Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C External Dimensions: 28" H x 15" W (including handles) Internal Dimensions: 22" H x 11.75" W Please note: Heating capacity is highly dependent on ambient temperature and use of insulation. Testing has shown that the Bucket Buddy can heat to 104°F in a room temperature ambient environment without insulation. Adding insulation may increase heating capacity while colder ambient environments may lower heating capacity. KegLand Part Number: KL20695

Read more less

This is a Blichmann Spare Part for the BeerGun Bottle Filler. Replacement Clip. Fits all models of the Blichmann BeerGun.

Read more less

Replacement O-ring kit for Blichmann RipTide™ pump.  

Read more less

No need to spend a ton of money on other paddles! This 24 in. Plastic Mash Paddle will get the job done!   The 24 inch Plastic Mash Paddle is a great and inexpensive way to stir your grain when doughing-in. It easily breaks up any clumps of grain in your mash, preventing dough balls from forming. Homebrewers love it because the durable plastic paddle will not scratch plastic mash tuns. These are 24" in length, a great size for 5 gallon cooler mash tuns!

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more in early March. No more spillovers! Set your desired volume and walk away Automatically collect water while you tend to other tasks Great for collecting brewing water or mixing your cleaning and sanitizing chemicals Illuminated display in splash resistant housing Integrated solenoid valve cuts off flow when your set volume is dispensed 1/2" BSP inlet and outlet work well with Duotight or Type A Camlock fittings Unlike other hose timers that simply measure time, the Fill-O-Meter measures volume and will automatically turn off when the programmed volume of water is dispensed. Enter your desired volume of water, press Start, and tend to other brew day prep work. Install in-line with your water filter to automatically collect filtered strike water, or measure out how much water you need to mix with cleaning chemicals for a precise dilution ratio. We recommend setting up the Fill-O-Meter with either Duotight fittings or Type A Camlocks. Thread tape will be required for the Camlock. Use sparingly as too much plumber's tape can damage the plastic thread. And it is very important to never overtighten! Displays real time flow rate and volume (Liters/Min or Gallons/Min) Accurately measures and controls volumes at flow rates from 1-30L/Min (0.26-7.9Gal/Min) Never overfill or spillover again Splash resistant housing Great for filling tanks, brewing kettles, distilling gear, mixing liquid and many other applications Integrated flow meter and solenoid valve Illuminated display for usage in the evening Integrated sound alarm Easy 1/2" BSP Inlet and Outlet Automatic failsafe - flow is stopped if the unit loses power Important Notes: DO NOT flow liquid the wrong direction, it will break the unit. DO NOT overtighten fittings onto the 1/2" ports. DO NOT exceed temperatures greater than 104°F (40°C) through the unit. Specifications: Flow Range: 1-30L per minute Temperature Range: 32-104°F (0-40°C) LCD: 3 inch back lit display Housing Material: ABS Input/Output threads: BSP 1/2" Pressure Rating: 0-12bar (0-180psi) Accuracy: +/- 5% Please Note: Accuracy can be improved with stable flow. Repeated start/stop or variation in water supply can have negative effect on accuracy. If you are noticing innaccurate fill levels, see the instruction manual for calibration instructions. KegLand Part Number: KL14694

Read more less

A perfect pocket temperature probe for homebrewing and BBQ! Check the temperature of your mash, whirlpool additions, or see if that mouthwatering tri-tip is ready to be pulled off the grill. With a range of -58°F to 572°F there's basically no way you won't get a temperature reading unless you live in an active volcano (do not recommend). Specifications: Range: -58°F – 572°F (-50°C – 300°C) Resolution: 0.1°C Temperature Error: +-1°C (0~100°C) Power Supply: 1 x AG13 Battery (included) Functions: On/Off °C/°F Hold KegLand Part Number: KL23320

Read more less

The BrewLab Plus® water test kit, model 7188-02, for home brewers quantifies 8 important water test factors. Includes everything in BrewLab Basic kit plus a high quality digital pH meter for monitoring batches from start to finish. Experts agree water conditions affect your final product, so take the mystery out of making great beer. Trust LaMotte, the water analysis experts since 1919, to help you control your most important ingredient—water! Visit HomeBrewFinds.com for a hands-on review of the LaMotte BrewLab water test kit. For more information on water and its role in the brewing process, check out Water, A Comprehensive Guide for Brewers written by John Palmer and MoreBeer!'s own Colin Kaminski. For help with water adjustments, download Palmer's Brewing Water Adjustment App, currently available for iOS devices and coming soon to Android. See the Documents Tab above for additional information.

Read more less

This thermometer will be a great addition to your homebrewing setup. The shorter 2.5" probe works great in a boil kettle or hot liquor tank because it’s easier to work around. Keep in mind that some brewers feel this is too short for a mash tun and prefer a longer thermometer which reaches closer to the center of the mash. (See our MT514 for the same thermometer with a 6" probe.)   Thermometer has an easy-to-read 3" Face, and 1/2" MPT threads on the back to connect to your kettle. The metal stem is durable and won’t break like glass can. Our reviewers agree that this is a great thermometer at a great price!    Standard Features: All Stainless Construction Fast Response to Temperature Change Hermetically Sealed (Moisture Proof) Within 1% Full Scale Accuracy Easily Calibrated With a Flat Head Screwdriver 316 Stainless Steel Stem Material Temperature range is 20-240F/0-110C. Calibration screw is 1/16th" hex nut.

Read more less

If you're installing a stainless thermowell or Temp Twister Cooling Coil on your FermZilla, this pipe cutter will help make the process painless. This easy to use pipe cutter makes cutting copper, stainless steel, or aluminum tubing an absolute breeze. Easy to use and compact so it can get into tight corners and gives you a clean pipe cut. Simply hand tighten the pipe cutter onto the mark where you want to cut the pipe. Rotate the cutter around the pipe a couple of times to create a groove all around the pipe, and then each time you rotate the cutter, tighten the blade a little. Each rotation will cut a little deeper into the pipe and the cut will be straight. Suitable for 1/8"-3/16" pipe (3-22 mm) Cuts copper, brass, aluminum, steel, and stainless steel Heavy-duty one-piece slide Polished roller for easy rotation Hardened steel cutting blade Kegland Part Number: KL14557

Read more less

Not all bi-metal thermometers are created equally, so if you’re looking for one that you don’t have to constantly tap to get an accurate reading, this is the thermometer to choose.   Other bi-metal thermometers have a helical coil in the stem that is tack welded to the stem itself causing hang ups to occur, and you have to tap the thermometer to get an accurate reading. Our new line of thermometers feature a super sensitive bimetallic helical coil suspended from a copper coated bushing fixed in the stem. This superior design provides a faster response to temperature changes and assures more accurate readings.   It's accurate to 1% of the total range, and it features a polished 2" stainless steel housing, hermetically sealed waterproof case and glass face for maximum durability. The unique anti-parallax dial also makes for easy reading.    This dial thermometer should be calibrated at 150 °F. Its temperature range is 0-220 °F (-10 to 100 degrees °C).    

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. The Ultimate FermZilla Combo Pack! Get the FermZilla Easy-Grip Tri-Conical & our most highly recommended accessories at an unbeatable price! Includes some of our favorite accessories for the FermZilla, such as the Pressure Kit with Floating Dip Tube so you're always racking the clearest beer, Duotight BlowTie 2 for pressure fermentations and flow control keg transfers, and Insulating Jacket to help maintain stable fermentation temps These accessories will help unlock the FermZilla's full potential, so buy them together and enjoy the savings! Combo Pack Includes: FermZilla Tri-Conical Easy-Grip Fermenter | 27L | 7.1G Pressure Kit w/ Floating Dip Tube Duotight BlowTie 2 Spunding Valve Insulating Jacket FermZilla Tri-Conical Easy-Grip Fermenter The FermZilla is the perfect option for brewers that want all the advantages of a conical fermenter without the price tag of a full-blown stainless-steel unit. It allows you to dump trub, harvest yeast, and with the addition of CO2 cylinder and regulator, you can carbonate and serve – all in one vessel! The clear PET tank allows you to visually monitor fermentation activity and is pressure rated to 2.4 Bar (34.8 psi), which means you can ferment under pressure, reducing ester and fusel alcohols in your finished beer. This also gives the ability to perform pressure transfers. If you prefer to move your finished beer to a keg or other vessel, you can do so with little to no oxygen exposure. The FermZilla Tri-Conical Easy-Grip model comes packed with accessories so you can take full advantage of this pressurizable fermenter on day one. The new stock standard includes Easy-Grip threaded lid ring, BlowTie spunding valve with integrated pressure gauge, ball lock carbonation caps for the lid and collection container, floating dip tube kit with weighted filter, volume marker graduation sticker, and adhesive thermometer.  What's Included: FermZilla 27L Tank with 3" T.C. Bottom Port Easy-Grip Threaded Lid Ring Integrated Gauge BlowTie Kit Spunding Valve (0-15 psi) Silicone Dip Tube Kit with Yellow Weighted Filter and SS Float (2) Yellow Liquid Carbonation Caps (2) Red Gas Carbonation Caps Fermzilla Pressure Lid with Red PRV (35 psi) 3" T.C. Butterfly Valve 600 mL Collection Container with 3" T.C. Connection Stainless Steel Stand with Swing Handles 3" tri-clamp with gasket Graduation Sticker Adhesive Thermometer Specs: 27 L (7.1 gal) Total Volume Pressure Rated to 2.4 Bar (34.8 psi) Height in Stand - 30.2" Tank Diameter - 13.9" Diameter in Stand - 15.3" Lid & Collection Container Ports - 28 mm PCO 1881 threads Temperature Rating: When not under pressure, do not expose to liquids above 131°F When under pressure, do not expose to any temperatures above 95°F* *Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years. Please note: when using the FermZilla under pressure, you must perform a water pressure check to ensure your connections are leak proof. To do this, fill your FermZilla up with water, apply at least 15 psi pressure, and check for leaks around all caps and threads.   Pressure Stress If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple: Fill the tank to the brim with water Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher Pressurize the tank to 4 BAR (58 psi) Check for leaks, then replace the Red PRV when finished If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla. General Care Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank.   KegLand Part number: KL47296 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.

Read more less

A powerful, 304 stainless steel heating element well suited for most kettles. With its weldless design and a diameter of 1.25", it's easy to install. Simply drill a 1.25" hole in your kettle and tightening the nut from the outside. The heating element requires a power cord which can be purchased separately. Electrical connection requires a computer power connection IEC320 C13 to your 110 or 220 v plug). Available in either 1600 watt 110 volt or 2200 watt 220 volt. Features: Food grade, high temperature silicone seal The element itself is 11.5" long, 0.75" diameter Designed for use with 5 gallon batches Please Note - Having electrical devices around liquid can be hazardous, and should not be left unattended. Please use caution while using this device, and read the instruction manual prior to use. Use the 1.25" Hole Saw to drill a hole for this product.   Kegland Part number: KL03513

Read more less

This is THE spoon for brew day!   Made of stainless steel, the homebrewer’s favorite. Nice long handle for stirring wort or mash in deep kettles & coolers. Won’t deteriorate over time like plastic. Easy to clean and sanitize.    21" in length.

Read more less

This carboy thermowell is used in conjunction with a Digital Controller to more accurately regulate internal temperature during fermentation. It is exceptionally useful during the start of fermentation when the lag between ambient temperature in the refrigerator and actual temperature in the carboy can vary greatly. Now you can keep your beer or wine within one degree of the set point on your digital controller. Designed to fit either 3, 5, 6, or 6.5 gallon glass carboys or any other similarly sized opening hole. The unit comes with a 15" stainless steel thermowell and a #6.5 stopper. The stopper has two holes measuring 3/8" and 1/4". Measures 14" from the bottom of the stopper to the end of the thermowell. Will not work with Johnson Temperature Controllers (FE600 or FE609) because the probes are too large.

Read more less

#7 stopper - solid. Top diameter 1.43 inches (36.3 mm), bottom diameter 1.19 inches (30 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. Max. Temperature Rating: 158 °F (70 °C).

Read more less

A simple, low cost pH meter eliminates the guesswork of using pH strips.  Simple 1-point calibration, accuracy to 0.1 pH units, and a pH 0-14 range make this tester incredibly easy to live with. No more guessing at your mash pH! Includes calibration screwdriver, batteries and user manual. Milwaukee Part Number: pH600AQ  

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. The Hop Bong is a versatile pressurizable tri-clamp accessory, capable of not only dry hopping oxygen purged hops into fermenters, but also as an inline carbonation/oxygenation accessory. Load up the Hop Bong, flush it with CO2, purge out oxygen with the handy PRV on top, then simply open the Butterfly Valve to inject your beer with a 6 oz payload of dry hops. If you're an existing FermZilla Conical or All Rounder user and you already own the Pressure Kit with 2x Ball Lock Caps and floating dip tube, check out the Hop Bong Upgrade Kit. The 3 Pieces of the Hop Bong Pressure Pack: Pressure Kit ​The Pressure Kit includes two Ball Lock Caps with the Floating Dip Tube and Filter Attachment. These pieces allow you to pressure transfer finished beer out of the fermenter into kegs or a bottling bucket, or you can carbonate and serve beer directly from the FermZilla. Tri-Clamp Pressure Lid Replacing the standard lid with the FermZilla Tri-Clamp Pressure Lid provides you with a 2" T.C. port at the top of your fermenter. This will give you an opening to add dry hops or other additions without needing to remove the entire lid. Take off the butterfly valve to add your yeast pitch, and when you're ready to add flavoring additions when fermentation is complete, drop them in oxygen-free via the Hop Bong. PCO1881 threaded ports are there for your Ball Lock Caps, as well as undrilled ports for an optional Thermowell and/or Temp Twister cooling coil. Hop Bong Load up the Hop Bong and add CO2 to purge your hop charge of oxygen. This kit comes with a third Ball Lock Cap to introduce CO2 directly to the Hop Bong, as well as a pull ring PRV to release pressure and purge oxygen. Once you've flushed your hop charge with CO2, open the butterfly valve to inject your beer with up to 6 oz of hop pellets. Hop Pellet Capacity: 150–180g (5.2–6.3 oz) Kit Includes: FermZilla 2" T.C. Pressure Lid Starter Kit 2" Hop Bong 2" FermZilla Tri-Conical Butterfly Valve Floating Dip Tube Weighted Mesh Filter Attachment (KEG6571) Red PRV & PCO1881 Cap Combo Yellow Ball Lock Cap (2) Red Ball Lock Caps (2) 2" Tri-Clamps (2) 2" Silicone T.C. Gaskets KegLand Part Number: KB10897 Installation Note: For best performance, ensure there is not an excess amount of slack when the silicone dip tube is installed and shorten it if needed. With the floating dip tube installed on your empty FermZilla, you ideally want the dip tube to hang freely with just enough length for the end of the dup tube to touch the bottom of the tank. Warning: Always depressurize your system COMPLETELY before removing fittings from your fermenter.

Read more less

Track your fermentation progress without ever disturbing your wort! The Tilt Hydrometer and Thermometer is added directly to your fermenter to provide real-time data on the current gravity and temperature of your wort, eliminating the hassle and potential contamination that comes from opening your fermenter to pull samples. The Tilt is especially useful for brewers fermenting in glass carboys or plastic fermenters that don't have spigots for sample taking. Designed for homebrewing, the Tilt hydrometer lets you instantly read your brew's specific gravity and temperature on your compatible Apple iPhone/iPad or Android smartphone/tablet or Tilt Pi. Most Bluetooth 4.0+ devices will work with the Tilt. You can then optionally log data to the cloud using their free Google Sheets template or other 3rd party cloud platforms. Tilt's goal is to help homebrewers brew better beer. The Tilt hydrometer allows you to check the specific gravity and temperature of your beer while it's fermenting, without ever having to open your fermenter or pour out any of your precious brew. This makes brewing more consistent and easier to track. Here are some of the new features of the Tilt: Range: Better reception and range. With the increased transmission power your Tilt will send data through larger, thicker-walled fermenters. Precision: Upgraded sensors. With an improved temperature sensor and accelerometer your Tilt will operate with more precision. Efficiency: Reduced power consumption so more brews, less battery changing. New Look: Newly designed custom circuit board and harness. If using multiple Tilt hydrometers for different batches of fermenting beer you must use a different color for each batch. The app will not read multiple hydrometers of the same color. Each Tilt comes calibrated and ready to go with a pre-installed battery that lasts 12-24 months depending on usage. Just download the free app, sanitize your Tilt, drop it in your fermenter, and start taking readings with your phone, tablet, or Tilt Pi. The specific gravity is accurate +/- 0.002 within the Tilt's range of 0.990 to 1.120. The thermometer is accurate +/- 1°F (+/- 0.5°C). Download the free Tilt app at the Apple App Store or Google Play Store or get the free Tilt Pi download.

Read more less

Accurately measure your starting and finishing gravity in beer or wine Triple scaled in specific gravity, potential alcohol, and sugar per liter Color coded scale referenced for beer and wine Comes with storage case and directions Made in France Our basic hydrometer is an essential tool for testing starting and finishing beer gravity, or sugar content, in beer or wine fermentations. Has three scales—specific gravity, potential alcohol, and sugar per liter. 9" long. Comes in storage case with complete, helpful directions. Scale Ranges: Specific Gravity: 0.980–1.150 Potential Alcohol: 0–18% Sugar Per Liter: -60–340 Converting SPL to Brix One degree Brix is equal to one gram of sugar per 100 mL of solution. Since a liter is equal to 1000 mL, you can calculate the Brix by dividing Sugar Per Liter by 10. Therefore, a must that contains 210 grams of sugar per liter is equal to 21 Brix.

Read more less

The Stainless Bucket Fermentor is the perfect fermentation vessel for 5 gallon batches. The small design enables it to easily fit inside a refrigerated unit. Also available in 4 gallon size for 2.5 to 3 gallon batches. Features: 304 Stainless Steel Coned Bottom Embossed Level Markings Rotating Racking Arm Includes Ball Valve, Airlock, and Stopper Liquid Crystal Thermometer Dimensions: Height - 19.5" to top of lid (Add 6.25" for airlock and stopper) Width - 16.5" handle to handle Depth - 15.25" including valve

Read more less

Want an easy-to-use, stainless vessel that ferments and carbonates? This 29L/7.6 Gallon keg has been modified to allow you to do both! The top is fitted with a large 4 inch tri-clamp lid with two ball lock posts and a pressure relief valve. You can use this vessel to ferment, carbonate, serve, or push the beer through a filter. The posts are recessed which allows you to stack these kegs up to 4 high. A 4" T.C. end cap with pre drilled hole is also available (H691), which can be paired with a #3 stopper and airlock. Also consider the Kegmenter Hop Bong Pressure Pack which allows for oxygen-free dry hopping and also features ball lock posts for Gas & Liquid. Depending on how long it will take to consume the finished beer, we recommend using two kegmenters, one for fermentation and one for carbonating and serving. After fermentation, there will be a large trub cake at the bottom of the vessel. Leaving finished beer on the trub for too long (2-3 weeks) may eventually lead to off-flavors. Check out our ball lock jumper line (KEG575) to easily transfer from one kegmenter to the other. Also consider our beer filter kit (FIL40), which will allow you to filter the beer during transfer. Features: Rated up to 2.5 BAR (36 psi) 4" T.C. lid with ball lock posts Floating dip tube Stainless steel 1.8 mm thick Use: As a stainless steel fermenter that is easy to clean Great choice for 5 gallon fermentations Easy to pressurize the kegmenter after fermentation to push through a filter and into another keg Fermenting under pressure, allowing CO2 to exit via the relief valve, reduces esters and fusel alcohol production allowing you to ferment at warmer temperatures Distillation - with the addition of a T.C. reducer and condenser (H701 / DS120 / DS130) As a cellar keg for topping up barrels Warning: Always depressurize keg before removing lid. Does not include spunding valve shown in example photo. Please see FIL42A. Kegland Part number: KL05906

Read more less

Savvy homebrewers love quick disconnects on their gas lines! They give you the ability to quickly move hoses from one configuration to another with ease! These quick disconnects feature 1/4" barbed fittings which can be used with 3/16", 1/4" or 5/16" line. The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you don’t need to worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade Buna-N. In short, these QDs are durable, user friendly and versatile. A no-brainer! For the male side, see our H550A, or buy both sides together as a set.

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in late March.   Don't run away from this Evill Twin! Instead, run toward and embrace it like a long lost sibling. The Evill Twin Roller Mill is the perfect sidekick for any brewer needing to grind malted and non-malted barley, corn and other grains. Operation is smooth and easy thanks to the longer mill shaft. Unlike other manual mills, the crank on the Evill Twin connects to the shaft far enough away from the mill body that you won't scrape your knuckles on the grain bucket with every revolution. Better yet, the mill shaft comes ready to hook up to an electric power drill with no extra parts needed. Run your drill at 500 RPM and you'll be able to crush up to 6 pounds per minute! The adjustable gap setting allows you to customize your grind to the size of the grain, and thanks to the stainless steel construction, you can rest assured that this mill will last as long as its malevolent disposition. Features: Easily adjustable gap setting Hopper holds 10 lbs Mill shaft comes ready to connect to an electric power drill With the drill running at 500 RPM, crush up to 6 lbs/minute Rollers and hopper screws made from stainless steel Frame, hand crank and hopper made from aluminum Please note: This mill is designed for use with brewing grains only. It will not work for cracking whole kernel corn.

Read more less

Fits PET Carboys. A breathable Silicone stopper that acts as both a stopper and an airlock. Unique design allows CO2 pressure to escape but keeps Oxygen and airborne contamination out. Quickly became our stopper of choice for wine. Used by numerous commercial wineries. Also has great application for beer ferments: Will create a vacuum if fermenting wort cools (as opposed to pulling water in from your traditional airlock.) Air tight seal is great for extended fermented lager when CO2 production is still present but very slight.

Read more less

Replacement 3mm thick gasket for the 35L Distillation Lid. Note: The 3mm gasket works well with Gen 3 and older BrewZillas and Gen 1 DigiBoils. If you have a newer model, we recommend the 6mm Gasket for a better seal. To improve the seal further, we highly recommend using the Adjustable Lid Clamps with the Distillation Lid if your unit does not have them. KegLand Part Number: KL03490

Read more less

Upgrade your home brewery with an innovative, Stainless Steel, 3.5 Gallon Brew Bucket™ Fermenter!  Many have asked for a smaller BrewBucket, and that has been heard.  The Brew Bucket mini is perfect for 2.5 gallon batches.  With features similar to the original 7 gallon Brew Bucket, the Mini is a great way to do smaller batches.  Whether you are interested in splitting a 5 gallon batch for experimenting, or just brew 2.5 gallons, the BrewBucket Mini is a great choice. Featuring a conical bottom, 304 SS construction, a rotating racking arm valve, and stackable design, these are space saving feature rich fermenters that are easy and enjoyable to use.  We inspected and used the Brew Bucket™ and one of the most unique features that stood out is that the Brew Bucket can be stacked during fermentation, even with an airlock attached. We also like the conical bottom that allows trub to settle out in a concentrated space that minimizes the surface area of the trub that is in contact with your beer.  The included Patent Pending Rotating Racking Valve is also a brilliantly simple design allowing you to rotate the racking arm inside the Brew Bucket down during fermentation to minimize trub, and later up to get clear beer when racking!   Etched Volume Markers on the inside were super handy when filling. The build quality is really amazing for the price. Welds are clean. The lid is strong and the spring loaded lid hatches are solid.  The lid includes a removable, molded silicone gasket that ensures an airtight seal.  We love an airtight seal so that we can be sure to see the airlock working. The welded on stainless handles make the BrewBucket fermentor super easy to move.  Features: 304 SS Food Grade Construction Rotating Racking Arm & Valve (Patent Pending) 3.5 Gal Max Capacity (2.5 gal Batches) 40° Conical Bottom for Trub Trapping Nests for Storage & Stacks for Ferment! SS lid w/ Silicone Gasketed seal Spring Loaded Lid Clamps for Airtight Lid Seal Offset Airlock Hole includes Silicone Stopper Gallon Markers inside for visual volume assessment Stainless construction resists damage and is easy to clean 8.5" Bottom Width / 11" Top Width x 16" Height Please note: the thermowell pictured in the second photo is not included.  

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. The Hop Bong is a versatile pressurizable tri-clamp accessory, capable of not only dry hopping oxygen purged hops into fermenters, but also as an inline carbonation/oxygenation accessory. This upgrade kit is for existing FermZilla Tri-Conical and All Rounder Fermenter users that already own the Plastic Pressure Kit with 2x Ball Lock Caps and Floating Dip Tube. If you already own these pieces, then you just need the two accessories below for a complete Hop Bong Pressure Pack. Tri-Clamp Pressure Lid Replacing the standard lid with the FermZilla Tri-Clamp Pressure Lid provides you with a 2" T.C. port at the top of your fermenter. This will give you an opening to add dry hops or other additions without needing to remove the entire lid. Take off the butterfly valve to add your yeast pitch, and when you're ready to add flavoring additions when fermentation is complete, drop them in oxygen-free via the Hop Bong. PCO1881 threaded ports are there for your Ball Lock Caps, as well as undrilled ports for an optional Thermowell and/or Temp Twister cooling coil. Hop Bong Load up the Hop Bong and add CO2 to purge your hop charge of oxygen. This kit comes with a Ball Lock Cap to introduce CO2 directly to the Hop Bong, as well as a pull ring PRV to release pressure and purge oxygen. Once you've flushed your hop charge with CO2, open the butterfly valve to inject your beer with up to 6 oz of hop pellets. Hop Pellet Capacity: 150–180g (5.2–6.3 oz) Kit Includes: FermZilla 2" T.C. Pressure Lid Starter Kit 2" Hop Bong 2" FermZilla Tri-Conical Butterfly Valve Red PRV & PCO1881 Cap Combo Red Ball Lock Cap (2) 2" Tri-Clamps (2) 2" Silicone T.C. Gaskets Does Not Include: Yellow Ball Lock Cap Secondary Red Ball Lock Cap Floating Dip Tube with Filter Attachment KegLand Part Number: KB10921 Warning: Always depressurize your system COMPLETELY before removing fittings from your fermenter.

Read more less

The Zahm SS-60 Volume Meter was developed to determine average CO² levels of gas in tank stored beverages. Its improved design over the older Zahm-Hartung Volume Meter (Series 2000) greatly improves accuracy and time required to run a test. A precise piston release mechanism eliminates bleeding off of the sample and the potential for human error. Samples undergo repeatable, precise volumetric expansion test after test for more accurate measurements. The lightweight design reduces operator fatigue while the stainless steel construction increases strength and resists corrosion. The thermometer may also be replaced in the field without the need to return it to the factory for replacement. The parts list and line drawing should be used when ordering replacement parts or operating the instrument.  

Read more less

Use this insulating jacket to regulate the fermentation temperature in your 30L FermZilla All Rounder. The jacket alone will help keep your fermenter warm in the colder months, or you can add a FermWrap heater if the heat fermentation isn't enough to maintain temp. Conversely, you can freeze bottles of water and put them inside the jacket to keep the temperature from getting too hot. If you're feeling extra fancy, use frozen water bottles and a FermWrap plugged into a temperature controller. The frozen water bottles will provide constant cooling, and if the controller detects that the temperature has dropped too far, it will kick on the FermWrap to heat your fermenter back up to your target temp. The jacket has the added benefit of protecting your fermenting beer from harmful UV light. Features a single sided zipper and draw string bottom. Kegland Part number: KL19590

Read more less

This is a replacement stopper for our Counter Pressure Bottle Fillers. This will work with both KEG801 & KEG804. Stopper - #2.5 with 3/8" hole.

Read more less

Get organized in your brew area and mount your water or beer filter assembly to a wall or directly to your system. Brackets are designed to mount to the top of the canister housing. Screws included.

Read more less

The IceMaster 100 is a powerful and efficient glycol system that provides precise temperature control of multiple Fermenters, but allows you to expand your capacity as needed! Temp Control & Cold Crash up to 4 - 5-7 Gallon Jacketed Tanks! Tank Capacity: 30L/8 Gal. Water Capacity Cooling Capacity: 780 Watt/2600btu/0.26 ton Power: 110V (3.6 amps) The IceMaster 100 is designed to cool fermentations in small vessels. It can be used with any vessel that has a glycol jacket or submersed cooling coil/rod. For each vessel you want to cool you will need to buy one of our BrewBuilt Chilling Pump Kits. Each tank is able to be separately temperature controlled. Each Glycol Pump Kit includes a submersible pump that is placed in the cool bath of this chiller along with a digital controller. The digital controller includes a thermal probe that should be inserted into a thermal well in your vessel or can be taped to the outside of the vessel if you don't have a thermal well. The digital controller then measures the temperature of your tank and turns the submersible pump on or off to cool to your desired set temperature. Up to four tanks can be controlled separately with one IceMaster and four BrewBuilt Chilling Pump Kit (GLY35). Compatibility The IceMaster can be used with any fermenter that has a built in cooling jacket, added Coolstix, or a submersed cooling coil. It works well as the cooling source for the following sytems and fermenters. BrewBuilt Jacketed Uni Conical - You will need one Glycol Pump Kit for each tank. Coolstix - Coolstix can be added to a wide range of carboys, fermenters, and tanks and the IceMaster works really well in combination. Each Coostix Complete Kit comes with a pump kit and controller. Ss Brewtech Fermenters and Brites with optional FTS Temperature Control Systems - Because FTS systems include a pump and controller you will not need to buy a separate Glycol Pump Kit. Spike Conical with Optional Cooling Package - Because the optional Spike cooling system includes a pump and controller you will not need to buy a separate Glycol Pump Kit. Speidel Tanks with Optional Cooling Jackets - You will need one Glycol Pump Kit for each tank. Grainfather Fermenters - Grainfather fermenters have standard cooling jackets. You will need one Glycol Pump Kit for each fermenter Blichmann Fermenators with Optional Cooling Coil - You will need one Glycol Pump Kit for each Fermenator. Capacity It is always difficult to determine exactly how many tanks can be chilled at one time as it depends on what is happening in each tank, if the tank is insulated, and what the ambient temperature is. Cold crashing always requires the most energy and requires tank insulation. We have experimented with capacities and can provide this general guide based on a 75°F ambient and neoprene insulation. Neoprene a modest amount of insulation so you would obtain better results using Armaflex or a higher R rated insulation. If only controlling fermentation temps the capacity would be higher. Four BrewBuilt Chilling Pump Kits (GLY35) is the maximum that will fit in the IceMaster. We are working on smaller glycol pump kits, where the pumps have smaller footprints, so the IceMaster right now has the capacity to use 5 pumps through the bulkhead fittings. Capacity calculated at cold crashing to 38°F at 75°F ambient with neoprene insulation (double for fermentation temperature control): 2 - 1BBL (31 Gallon) Jacketed Tanks 2 - 1/2BBL (15-20 Gallon) Tanks 3 - 10-14 Gallon Tanks 4 - 5-7 Gallon Tanks Set Up In order to hook up the IceMaster to your fermenter or tank's cooling system, you will need 4 lengths of tubing. All tubing connections should be secured with hose clamps. Length 1: Submersible pump outlet to inner barb of 1st bulkhead Length 2: Outer barb of 1st bulkhead to cooling system inlet Length 3: Cooling system outlet to outer barb of 2nd bulkhead Length 4: Inner barb of 2nd bulkhead to IceMaster resevoir (should drain freely, no connection necessary) Specifications: Tank Capacity: 30L/8 Gal. Water Capacity Compressor: 3/8 HP Cooling Capacity: 780 Watt/2600btu/0.26 ton Refrigerant: r134a Voltage: 110V (3.6 amps) Dimensions: 410mm x 410mm x 660mm Includes 10 stainless bulkheads with 3/8" OD barbs Wheels included CE Certified Warning: Do not set the reservoir temperature controller lower than 28°F (-2ºC). Running the unit below this temperature may negatively affect the unit's efficiency and has the potential to freeze beer which may impact the finished beer's flavor.

Read more less