Detecting your location...
EARLY HOLIDAY DEALS Up to 35% off brewing gear Hundreds of items marked down · No code needed
Shop the Sale

Duotight BlowTie | Complete Kit | Diaphragm Spunding Valve | 0-15 PSI | 8 mm Duotight

    Description

    • Holds a set pressure in your fermenter or keg by automatically venting excess CO2
    • Diaphragm design is more accurate than spring and poppet spunding valves, especially at lower pressures
    • Ideal for pressure fermentation and keg-to-keg, fermenter-to-keg and keg-to-bottle transfers
    • Includes a 0-15 PSI push-in gauge so you can monitor vessel pressure at a glance
    • Comes complete with a Duotight ball lock QD, ready to use right out of the box

    BlowTie Spunding Valve Complete Kit
    The BlowTie lets you set and hold the pressure inside a vessel while it vents. As your beer ferments or transfers, any CO2 above your set point is released, and the rest stays in the vessel. Use it to ferment under pressure, or to keep head pressure on the receiving keg during closed transfers so your beer holds its carbonation.

    Why a Diaphragm Spunding Valve?
    Traditional spring and poppet spunding valves have a gap between the pressure at which they open and the pressure at which they reseal. The BlowTie uses a diaphragm instead, so once excess gas is released, the pressure left in your vessel ends up much closer to the pressure you set. It is also more accurate at the low pressures used for most homebrew fermentations.

    Setting Your Pressure
    Turn the yellow knob on top of the BlowTie clockwise to raise the pressure setting and counterclockwise to lower it. To dial it in, start with a keg that is carbonated or pressurized to a known pressure (for example, 15 PSI). Attach the kit and turn the knob until gas begins to release at your target pressure (for example, 10 PSI).

    Easy to Clean
    The BlowTie is made from food-grade acetal with stainless steel screws, and it comes apart with a Phillips screwdriver for cleaning.

    Kit Includes:

    • 1 x BlowTie Diaphragm Spunding Valve
    • 1 x Duotight 8 mm (5/16 in.) Female x 8 mm (5/16 in.) Female Tee
    • 1 x 8 mm Push-In Pressure Gauge, 0-15 PSI
    • 1 x Duotight 8 mm (5/16 in.) Ball Lock Disconnect, Gray/Gas
    • 2 x 8 mm Rigid Plastic Joiners

    Specifications:

    • Pressure range: 0-15 PSI
    • Connections: 8 mm (5/16 in.) Duotight push-in on inlet and outlet
    • Body material: food-grade acetal
    • Screws: stainless steel

    Please note: The rigid joiners are semi-permanent once pushed in and are difficult to remove. If you want a setup you can fully take apart, use short pieces of 8 mm OD EVABarrier tubing in place of the joiners.

    WARNING: Do not exceed the gauge's 15 PSI rating. Exceeding the pressure range will damage the gauge.

    KegLand Part Number: KL09706

    Duotight BlowTie | Complete Kit | Diaphragm Spunding Valve | 0-15 PSI | 8 mm Duotight

      Product form

      SKU: FE9610

      <p>Earn%20[points_amount]%20when%20completing%20this%20purchase.</p>

      $32.99

      Calculating shipping time...
      Shipping
      Free Shipping*
      Shipping
      Paid Shipping
      Drop Ship
      Drop Ship
      Discount Exclusion
      Discount Exclusion
      Freight
      Freight Only
      Pre-book
      Pre Order

        Prop 65 Warning WARNING : This product can expose you to chemicals including Lead and lead compounds, which is/are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov.

        Description

        • Holds a set pressure in your fermenter or keg by automatically venting excess CO2
        • Diaphragm design is more accurate than spring and poppet spunding valves, especially at lower pressures
        • Ideal for pressure fermentation and keg-to-keg, fermenter-to-keg and keg-to-bottle transfers
        • Includes a 0-15 PSI push-in gauge so you can monitor vessel pressure at a glance
        • Comes complete with a Duotight ball lock QD, ready to use right out of the box

        BlowTie Spunding Valve Complete Kit
        The BlowTie lets you set and hold the pressure inside a vessel while it vents. As your beer ferments or transfers, any CO2 above your set point is released, and the rest stays in the vessel. Use it to ferment under pressure, or to keep head pressure on the receiving keg during closed transfers so your beer holds its carbonation.

        Why a Diaphragm Spunding Valve?
        Traditional spring and poppet spunding valves have a gap between the pressure at which they open and the pressure at which they reseal. The BlowTie uses a diaphragm instead, so once excess gas is released, the pressure left in your vessel ends up much closer to the pressure you set. It is also more accurate at the low pressures used for most homebrew fermentations.

        Setting Your Pressure
        Turn the yellow knob on top of the BlowTie clockwise to raise the pressure setting and counterclockwise to lower it. To dial it in, start with a keg that is carbonated or pressurized to a known pressure (for example, 15 PSI). Attach the kit and turn the knob until gas begins to release at your target pressure (for example, 10 PSI).

        Easy to Clean
        The BlowTie is made from food-grade acetal with stainless steel screws, and it comes apart with a Phillips screwdriver for cleaning.

        Kit Includes:

        • 1 x BlowTie Diaphragm Spunding Valve
        • 1 x Duotight 8 mm (5/16 in.) Female x 8 mm (5/16 in.) Female Tee
        • 1 x 8 mm Push-In Pressure Gauge, 0-15 PSI
        • 1 x Duotight 8 mm (5/16 in.) Ball Lock Disconnect, Gray/Gas
        • 2 x 8 mm Rigid Plastic Joiners

        Specifications:

        • Pressure range: 0-15 PSI
        • Connections: 8 mm (5/16 in.) Duotight push-in on inlet and outlet
        • Body material: food-grade acetal
        • Screws: stainless steel

        Please note: The rigid joiners are semi-permanent once pushed in and are difficult to remove. If you want a setup you can fully take apart, use short pieces of 8 mm OD EVABarrier tubing in place of the joiners.

        WARNING: Do not exceed the gauge's 15 PSI rating. Exceeding the pressure range will damage the gauge.

        KegLand Part Number: KL09706

        Important Warnings & Shipping Info +
        Shipping Icon
        Free Shipping: Fast & Free Shipping over $79
        Shipping Icon
        Shipping Rates Apply: Bulk items like grain, bottles, and malt are excluded from our free shipping promotion due to their weight, and often dropship items. Standard shipping rates apply and are calculated at checkout based on your location and order size.
        Drop Ship Icon
        Drop Ship: This product will ship directly from the supplier. Delivery may take 1-4 weeks depending on the vendor.
        Discount Exclusion Icon
        Discount Exclusion: This item is not eligible for sitewide price reductions or percentage discounts. Learn more.
        Freight Icon
        Freight Shipping: This item ships freight only.
        Pre-book Icon
        Pre Order: This item is available for Pre-Order. Full payment is required to reserve stock.
        Shipping Weight: 0.4 lb

        Login

        Forgot your password?

        Don't have an account yet?
        Create account