This 30W Heating Belt will gently warm your fermenter without creating major hot spots. Heating belts are often chosen over heating pads for the simplicity of adjusting the height of the belt on your fermenter to increase or decrease the heat transfer. And they're especially useful for smaller vessels where a heating pad would be simply too large.
For the best results, pair the Heating Belt with a temperature controller so that heating is only provided when your fermentation drops below your set point. If you're using a fermentation chamber or other form of chilling, the temperature controller will be able to switch between heating and cooling as needed.
Comes with a standard 2-prong US style 110V plug. Please disregard the example photo that shows an AU style plug.
KegLand Part Number: KL01953
This flat lid with pre-drilled holes allows you to easily add a Temp Twister Cooling Coil to your 35L Bucket Buddy fermenter. It also has holes for your stopper & airlock (included with the Bucket Buddy) as well as a Thermowell so you can control the circulation of cooling solution with a Temperature Controller. The lid is also compatible with 35L BrewZillas and DigiBoils. If you're fermenting in the Bucket Buddy with built-in heating element, we recommend plugging the unit into the heating outlet of your temperature controller and leaving the power switch turned on. This will allow the temp controller to provide power to the unit only when heating is needed and it will cut the power as soon as you're back to your set temperature. Using the Bucket Buddy's controller to maintain the heating set temp and using a separate controller to maintain the cooling may result in heating and cooling cycling at the same time. NOTE: The pre-drilled holes are meant for specific sizes of Duotight bulkheads and the stopper included with the Bucket Buddy fermenter. All holes need to be occupied in order to protect your fermentation from outside contaminants. Depending on the placement of the Temp Twister, you might need to shorten the inlet/outlet tubes on the outside of the fermenter using a Pipe Cutter. Lid only. Other accessories must be purchased separately. You Will Also Need: Temp Twister Cooling Coil FermZilla Thermowell Temperature Controller KegLand Part Number: KL28103
This Reactor Rod was custom built to be used with the 1 bbl MoreBeer! Pro Conical Fermenter, but can easily be integrated to other vessels with a 4" tri-clamp top port. Unlike other in-solution cooling coils on the market, the Reactor Rod utilizes a straight vertical design. Without all the curves and bends of a cooling coil, it is easier to scrub and sanitize the unit prior to setup and after use. The four cooling rods are 32" long measured from the bottom of the T.C. fitting.
This Reactor Rod was custom built to be used with the 2 bbl MB Conical Fermenter, but can easily be integrated to other vessels with a 4" tri-clamp top port. Unlike other in-solution cooling coils on the market, the Reactor Rod utilizes a straight vertical design. Without all the curves and bends of a cooling coil, it is easier to scrub and sanitize the unit prior to setup and after use. The four cooling rods are 41" long measured from the bottom of the T.C. fitting.
The German made 1.2 horse power MB Chiller is an ideal solution for nano breweries looking to chill up to 10 fermenters at once. The idea of the MiniChilly is that for each fermenter you want to a chill a pump kit is added. A pump kit (GLY35) includes a submersible pump that is placed in the cold bath of the Mini Chilly along with a digital controller that is placed next to your fermenter. Silicone tubing is included to make the connections. The digital controller includes a thermal probe that should be inserted into a thermal well in your vessel or can be taped to the outside of the vessel if you don't have a thermal well. The digital controller then measures the temperature of your tank and turns the submersible pump on or off to cool the liquid in your vessel to the desired set temperature. In this way each tank can be set at different temperatures. The MiniChilly is made by Quantor/Kreyer of Germany who is the largest manufacturer of glycol systems for breweries and wineries in the world. Made with high quality manufacturing and components, the MiniChilly is a durable system for many years of problem-free brewing. It is German made and we guarantee you will appreciate the build quality when compared to other chillers on the market. The unit features a stainless steel case with stainless 3/8" barbs in the top that allow for a clean connection of the silicone tubing that will run from each pump to each tank. The MiniChilly is able to chill its reservoir down to 21°F when a 30% glycol solution is used. The compact size and included casters make it easy to move around the brewery when needed. Applications: Cooling of Fermentation Cold Crashing for Brite Tanks Maintain Lagering Temperatures Compatibility: The MiniChilly can be used with any fermenter that has a built-in cooling jacket or a submersed cooling coil. It works well as the cooling source for the following systems and fermenters. BrewBuilt Jacketed Uni Conical - You will need one Glycol Pump Kit for each tank. Ss Brewtech Fermenters and Brites with optional FTS Temperature Control Systems: Because FTS systems include a pump and controller you will not need to buy a separate Glycol Pump Kit. Spike Conical with Optional Cooling Package - Because the optional Spike cooling system includes a pump and controller you will not need to buy a separate Glycol Pump Kit. Speidel Tanks with Optional Cooling Jackets - You will need one Glycol Pump Kit for each tank. Grainfather Fermenters - Grainfather fermenters have standard cooling jackets. You will need one Glycol Pump Kit for each fermenter Blichmann Fermenators with Optional Cooling Coil - You will need one Glycol Pump Kit for each Fermenator. Capacity: Many chiller ratings are based on the theoretical power of the compressor, while the cooling capacity of the MiniChilly is rated at a realistic ambient temperature. This is much more useful for predicting the MiniChilly’s performance in real world applications. Of course, you could cool a greater number of smaller tanks but you’re ultimately limited to the 10 connections. Actual cooling capacities will vary based on the insulation of the tank. For the examples below we assume neoprene or better. Cooling Capacity Example: Up to 10 1BBL (31 Gallon) well-insulated tanks fermenting at 68°F in 80°F ambient temperature. For every fermenter you want to cold crash remove 4 fermenting fermenters from the capacity. Set Up: In order to hook up the MiniChilly to your fermenter or tank's cooling system, you will need 4 lengths of tubing per pump. All tubing connections should be secured with hose clamps. Length 1: Submersible pump outlet to inner barb of 1st bulkhead Length 2: Outer barb of 1st bulkhead to cooling system inlet Length 3: Cooling system outlet to outer barb of 2nd bulkhead Length 4: Inner barb of 2nd bulkhead to MiniChilly reservoir (should drain freely, no connection necessary) Technical Characteristics:
Power: 110V-1Ph/50-60Hz Compressor Power: 1.2hp/900watts Cooling Capacity at 32°F glycol temp and 90°F Ambient Temp: 1.05 KW/1050 Watts (60Hz 110V) Cooling Capacity at 60°F glycol temp and 90°F Ambient Temp: 1.92 KW/1920 Watts (60Hz 110V) Stainless Steel Unit Water Temperature Range: 21°F - 86°F (-6°C - 30°C) Ambient Temperature Range: 50°F - 90°F (10°C - 32°C) Refrigerant R134a Free Glycol Water-Bath for Mini-Pumps Fittings 3/8" for Plastic Tubes of Individual Pumps Solid Wheels w/ Breaks for Easy Mobility Universal C19 Plug On/Off Switch Water-Level Sight-Tube Grooves for Individual Pump Cables Safety Inner Separation Water Side from Electric Side Tank Capacity: 12.68 gal. (48 L) Dimensions: 29.5"L x 15.75"W x 21.75"H Weight: 112.5 lbs Made in Germany CE Certified
Heat resistant shelves for your brand new RAPT Fermentation Chamber. Can be used for trays of mushrooms or seed sewing with added grow lights. It can also be used as a humidity tray if you require a humid environment for your project. 60 mm (2.3") deep.
KegLand Part Number: KL25553
The Quantor MiniChilly 17 is highly recommended by Brewtools for chilling their F-series Unitanks. These glycol chillers are compact, high-quality units often used in professional settings. Made from stainless steel components and easy to install. They feature an integrated pump with a stirring function that ensures even temperatures throughout the reservoir. Rather than individual pumps for each fermenter, this unit is intended to be provide cooling solution to a single chilling loop where each fermenter will call for glycol circulation independently via solenoid valves. The MiniChilly 17 is recommended for up to 8 x 150L fermentation tanks of which 3 are cold crashed, or up to 4 x 300L fermentation tanks of which 1 is cold crashed. Check out the Brewtools cooling system page for setup details and recommended accessories for building a chilling loop with the MiniChilly 17. Specifications: Controller: EWplus 961 Power connector: Schuko - C19 Power: 790W (1+ HP) Refrigerant: R290 (Propane) Cooling capacity @ 32°F: 1000W (3412 BTU/hr) Cooling capacity @ 59°F: 1650W (5627 BTU/hr) Tank volume: 12.68 gal Dimensions: 29.5" x 16.5" x 23.6" 115V Manufactured in Germany by Quantor/Kreyer. NOTE: The product must stand still 24 hours before use after installation.
Replacement Non-Return Kit for Kreyer Chilly Max glcyol chillers. This kit comes standard on the Chilly Max 50 and Max 90. If your glycol system is positioned below the level of your jackets, heat exchangers or piping system, you may get back flow into the chiller's reservoir when the solenoid valves at all of your tanks are closed and the chiller's pump turns off. This Non-Return kit works with all Kreyer ChillyMax chillers to prevent this situation. The kit includes a one-way check valve which is installed inline on the chiller's outlet, and an electric solenoid valve installed on the chiller's inlet. The solenoid valve is wired to the relay that controls the chiller's pump such that when the pump turns off the valve closes. Simple to install and completely automatic, this kit allows you to keep the chiller's reservoir full and not worry about the placement in relation to the rest of your glycol system. Note: This only works with Chilly Max units. It will not work with any other chillers such as the Chilly 45. For the Chilly 45 Non-Return Kit, See related product.
Control the humidity of your cellar to prevent wine barrels from drying out Dry, non-humidified barrels will draw liquid to the outer surface where it evaporates, leading to significant product loss Can operate in environments as low as 34°F, making it ideal for cold rooms and storage halls Compact, stand-alone unit can be suspended from or mounted to a wall 9,900 cubic feet per hour air flow Made in Germany by Kreyer Humidity control in wine cellars plays a major role during the production, maturation and storage of wine and other beverages in wooden barrels. Wine barrels safe-guard the main asset of a winery – the wine itself. The wooden walls of dry, non-humidified barrels will draw liquid from inside it up through the small crevices to the outer surface where it evaporates. Over time, this leads to a significant amount of product loss. For example, a 225L wine barrel can lose 10-15% of the wine volume over one year. A professional humidification of the barrel room allows the barrel wood to absorb water-vapor, the crevices fill out and loss of wine is prevented. A well-kept barrel room is therefore cool, usually around 57-60°F and humidified at about 75% - 80% rH. As with every aspect of winemaking, attention and professional equipment are required. Low humidification may allow the wood to dehydrate and wine will evaporate through it, while overly high humidity can lead to mold and fungus. The centrifugal humidifier HumiFix is equipped with a spinning disk that vaporizes water into very fine droplets that can be easily absorbed by the surrounding air, humidifying and cooling a room at the same time. The unit can work either connected to your main water supply with inline cartridge filtration or more ideally to an RO unit. The HumiFix can work at low temperatures (down to 34°F), which is ideal for installation in cold rooms and storage halls. Features:
Stand-alone unit Easy installation and handling Compact construction Wall or suspended mounting Specifications:
Water Output: 6.5 L/h (1.69 Gal/h) Air Flow: 280 m³/h Power: 230 watts Power Connection: 110V/1Ph/60Hz Dimensions: 24" L x 20" W x 22.25" H Empty Weight: 40 lbs Please note: this unit comes with a bare cord so it can be hard wired to a controller. Otherwise we recommend attaching a 110V male plug and using it with the Inkbird Digital Humidity Controller.
A unique alternative to cooling plates. This tube-within-a-tube snake is used to recirculate glycol or cooled water through your ferment to keep temperatures down. It can be used in a tank, macrobin, or barrel. The inner vinyl tube runs through the middle of the corrugated stainless tubing, but is shorter than the stainless tubing. Glycol can run through one tube and back through the other, completing the loop.
Snakes are outfitted with 1/2in. male NPT threads on both the inlet and outlet. The inlet is at 90 degrees and the outlet is straight.
.75 Square Meters of Cooling Surface
Can also be used for heating
Optional silicon sleeve available for sealing
A unique alternative to cooling plates. This tube-within-a-tube snake is used to recirculate glycol or cooled water through your ferment to keep temperatures down. It can dropped directly into a tank, macrobin, or even barrel. The inner vinyl tube runs through the middle of the corrugated stainless tubing, but is shorter than the stainless tubing. Glycol can run through one tube and back through the other, completing the loop.
Snakes are outfitted with 1/2in. male NPT threads on both the inlet and outlet. The inlet is at 90 degrees and the outlet is straight.
.55 Square Meters of Cooling Surface
Can also be used for heating.
Optional silicon sleeve for sealing.
Replacement LCD control panel for the RAPT Fermentation Chamber.
This Replacement LCD screen has been flashed with the firmware for the RAPT Temperature Controller. It is not compatible with the RAPT Temperature Controller.
KegLand Part Number: KL17091
If your glycol system is positioned below the level of your jackets, heat exchangers or piping system, you may get back flow into the chiller's reservoir when the solenoid valves at all of your tanks are closed and the chiller's pump turns off.
This Non-Return kit works with Kreyer Chilly chillers (25, 35, 45) to prevent this situation. The kit includes a one-way check valve which is installed inline on the chiller's outlet, and an electric solenoid valve installed on the chiller's inlet. The solenoid valve is wired to the relay that controls the chiller's pump such that when the pump turns off the valve closes.
Simple to install and completely automatic, this kit allows you to keep the chiller's reservoir full and not worry about the placement in relation to the rest of your glycol system.
Use this Solenoid valve to control glycol flow into a fan unit. These Solenoids should be combined with a Fan Temperature Controller and Connection Cable to set a specific temperature for your fan unit to achieve in your room.
We recommend purchasing a Solenoid Filter with this valve. The filter will insure that no small particulates can get caught in the valve assembly, potentially damaging the unit.
230 v AC Solenoid with 1" FPT
We also sell complete control kits for Kreyer fan units:
MR75 & MR135 Control Kit
MR210 Control Kit
SD35L & SD73L Control Kit
When using a Kreyer Fan unit for below freezing temperatures, you must also use their matching defrost kit. Kreyer Defrost Kits consist of an electric heating element or spiral and are fitted directly to their respective fan unit cooling fins. The Defrost Kit melts any iced condensate that can accumulate on the fins when the fan is used with Glycol-Water set below the freezing point. The Defrost Kit will periodically melt any iced condensate allowing you to use your fan unit at low temperatures. Requires 230V Single Phase 50/60Hz Best if used with Kreyer Masterlog Controller (SDML) Please note: example image shown. The defrost kit may not exactly match this image.
When using a Kreyer Fan unit for below freezing temperatures, you must also use their matching defrost kit. Kreyer Defrost Kits consist of an electric heating element or spiral and are fitted directly to their respective fan unit cooling fins. The Defrost Kit melts any iced condensate that can accumulate on the fins when the fan is used with Glycol-Water set below the freezing point. The Defrost Kit will periodically melt any iced condensate allowing you to use your fan unit at low temperatures. Requires 230V Single Phase 50/60Hz Best if used with Kreyer Masterlog Controller (SDML) Please note: example image shown. The defrost kit may not exactly match this image.
When using a Kreyer Fan unit for below freezing temperatures, you must also use their matching defrost kit. Kreyer Defrost Kits consist of an electric heating element or spiral and are fitted directly to their respective fan unit cooling fins. The Defrost Kit melts any iced condensate that can accumulate on the fins when the fan is used with Glycol-Water set below the freezing point. The Defrost Kit will periodically melt any iced condensate allowing you to use your fan unit at low temperatures. Requires 230V Single Phase 50/60Hz Best if used with Kreyer Masterlog Controller (SDML) Please note: example image shown. The defrost kit may not exactly match this image.
Use your existing glycol system to cool your cellar Eliminates the need to purchase an entirely separate refrigeration system SD-S series fan units were designed specifically for high-moisture environments like wine cellars Sized for well-insulated rooms up to 85,000 ft³ Made in Germany by Kreyer Cool your cellar using your existing glycol system. Save energy and money! These units work under the same principles as standard refrigeration but use cooled glycol that you already have instead of cooled refrigerant gas, eliminating the need to have a separate refrigeration system. It is a fantastic use of your glycol system for a majority of the year when typically glycol systems are on but are being sporadically called upon. Glycol systems do need to be sized to accommodate both these fan units and peak duty during the crush to be able to accommodate all tasks at once. Glycol from your main glycol chiller is recirculated through these fan units. Aluminum fins act as heat exchangers drawing heat out of your room as the fins are cooled by the glycol. If you have a Kreyer chiller/heater you can even heat a space in cold weather environments. The heat exchangers inside the units are made from corrugated aluminum fins and internally grooved copper tubes. The white ABS casing looks great. Because of its rounded corners it has no water retaining areas favorable to germ development. Both series are fitted with stainless steel screws and show no sharp, cutting edges. Built in defrosters help ensure the system is working at optimum efficiency The SD-S series has been designed especially for problematic environments such as wine-cellars with high moisture. The high-performance fans on the SD-S unit are lubricated for life. Fan Unit Temp Control Upgrades: 1 in. Solenoid Valve - Allows or blocks flow of glycol through the fan unit. Needs to be connected to a Controller to function. A filter is recommended to protect the solenoid. 1 in. Solenoid Filter- protects the solenoid valve from any particulate or sediment. Glycol Fan Control Unit - Set a specific temperature on this controller and it will open and close the solenoid valve. Solenoid Connection Cable - This 2 meter long cable is required to connect the Solenoid Valve & Control unit. Inlet and Outlet: 1" Male BSP The SD-S 148 is sized to: Cool a room up to 85,000 cubic feet when the ceiling and walls are well insulated. Will use approximately 5.5 tons of cooling power from your chilling system. Please be sure to consult with our Wine team for proper sizing of a fan unit. This unit features 4 fans. Product Statistics Weight: 150lbs Dimensions: 82"L x 12"W x 18"H
This temperature and defrost controller is required when using a Kreyer defrost kit. The temperature control unit controls room/cooler/cave/cellar temperature when used in conjunction with a Kreyer fan unit. Kreyer fan units are plumbed to a Kreyer Glycol cooling unit. This unit turns on and off an optional solenoid placed at the inlet of the fan unit, which allows chilled glycol to enter the coils on the fan unit, while also turning on the fan(s) that blow cold air out into the room. When using a Kreyer Fan unit for below freezing temperatures, you must also use their matching defrost kit. Kreyer Defrost Kits consist of an electric heating element or spiral and are fitted directly to their respective fan unit cooling fins. The Defrost Kit melts any iced condensate that can accumulate on the fins when the fan is used with Glycol-Water set below the freezing point. The Defrost Kit will periodically melt any iced condensate allowing you to use your fan unit at low temperatures. For use with MR, SD-S, SD Plus, and TA Kreyer Fan Units. For a fan unit temperature controller to be used above freezing temperatures, see our GLY980.
Defrost Kits are electric heating elements made of a set of thin metallic heating rods that are fitted into the suitable slots, under the coil of the thermo-fan. This layout simplifies the installation and guarantees homogenous dispersion of heat over the entire coil for even defrosting. The Defrost Kit melts the iced condensate, which accumulates on the airways when the fan is used for room cooling with Glycol-water set below the freezing point. Periodical defrosting enables the use of the thermo-fan for setting up cold-rooms, which are kept at low temperatures. The melted condense water drips to the fan's collection tray for drainage.
When using a Defrost Kit, it is required to use the FermFlex-Defrost controller, which controls both the fan-valve for cooling and the heating element for defrosting.
Defrost Kits are electric heating elements made of a set of thin metallic heating rods that are fitted into the suitable slots, under the coil of the thermo-fan. This layout simplifies the installation and guarantees homogenous dispersion of heat over the entire coil for even defrosting. The Defrost Kit melts the iced condensate, which accumulates on the airways when the fan is used for room cooling with Glycol-water set below the freezing point. Periodical defrosting enables the use of the thermo-fan for setting up cold-rooms, which are kept at low temperatures. The melted condense water drips to the fan's collection tray for drainage.
When using a Defrost Kit, it is required to use the FermFlex-Defrost controller, which controls both the fan-valve for cooling and the heating element for defrosting.
Use this Solenoid valve to control glycol flow into a fan unit. These Solenoids should be combined with a Fan Temperature Controller and Connection Cable to set a specific temperature for your fan unit to achieve in your room.
This is a 3/4 in. FPT threaded piece for SD35L & SD73L Fan Units. It can also be used with other 1" SD fans if an adapter is used.
We recommend purchasing a Solenoid Filter with this valve. The filter will ensure that no small particulates can get caught in the valve assembly, potentially damaging the unit.
230 v AC Solenoid with 3/4" FPT
We also sell complete control kits for Kreyer fan units:
MR75 & MR135 Control Kit
MR210 Control Kit
SD35L & SD73L Control Kit
Cool your fermenting must or wine using this weldless, easy-to-install, 304 stainless steel cooling plate that can be inserted into the lid of any Variable Volume Fermenter. Cold water or glycol is recirculated through the cooling plates thereby reducing the temperature of your ferment.
This is a stainless steel setup, ensuring no chance of off-flavor in your wine. You drill two 1-1/16" to 1-1/8" holes into the lid. We provide two gaskets and a lock nut to seal on both sides of your lid, securing the plate in place.
Plate measures 31.5" H x 14.5" W
Inlet and Outlet 1/2" Male BSPP thread
300 mm long tubes
Bulkheads located approx. 175 mm above the plate
0.64 Square meters of cooling surface
Made from 304 stainless steel
Use your existing glycol system to cool your cellar Eliminates the need to purchase an entirely separate refrigeration system MR series fan units offer quieter operation compared to the SD-S units Sized for well-insulated rooms up to 8,750 ft³ Made in Germany by Kreyer Cool your cellar using your existing glycol system. Save energy and money! These units work under the same principles as standard refrigeration but use cooled glycol instead of cooled refrigerant gas, eliminating the need to have a separate refrigeration system. It is a fantastic use of your glycol system for a majority of the year when typically glycol systems are on but are being sporadically called upon. Glycol systems do need to be sized to accommodate both these fan units and peak duty during the crush to be able to accommodate all tasks at once. Glycol from your main glycol chiller is recirculated through these fan units. Aluminum fins act as heat exchangers drawing heat out of your room as the fins are cooled by the glycol. If you have a Kreyer chiller/heater you can even heat a space in cold weather environments. The heat exchangers inside the units are made from corrugated aluminum fins and internally grooved copper tubes. The white ABS casing looks great. Because of its rounded corners it has no water retaining areas favorable to germ development. Units are outfitted with stainless steel screws and show no sharp, cutting edges. Fan Unit Temp Control Upgrades: 1/2 in. Solenoid Valve - Allows or blocks flow of glycol through the fan unit. Needs to be connected to a Controller to function. A filter is recommended to protect the solenoid. 1/2 in. Solenoid Filter- protects the solenoid valve from any particulate or sediment. Glycol Fan Control Unit - Set a specific temperature on this controller and it will open and close the solenoid valve. Solenoid Connection Cable - This 2 meter long cable is required to connect the Solenoid Valve & Control unit. Specifications of MR210: Will cool well insulated spaces up to 8750 cubic feet while drawing 1 Ton of cooling power Triple Fan Unit 220V connection required to run fan You will need to connect to your existing glycol system Inlet and Outlet: 3/4" Male BSP
Use your existing glycol system to cool your cellar Eliminates the need to purchase an entirely separate refrigeration system MR series fan units offer quieter operation compared to the SD-S units Sized for well-insulated rooms up to 3,500 ft³ Made in Germany by Kreyer Cool your cellar using your existing glycol system. Save energy and money! These units work under the same principles as standard refrigeration but use cooled glycol instead of cooled refrigerant gas, eliminating the need to have a separate refrigeration system. It is a fantastic use of your glycol system for a majority of the year when typically glycol systems are on but are being sporadically called upon. Glycol systems do need to be sized to accommodate both these fan units and peak duty during the crush to be able to accommodate all tasks at once. Glycol from your main glycol chiller is recirculated through these fan units. Aluminum fins act as heat exchangers drawing heat out of your room as the fins are cooled by the glycol. If you have a Kreyer chiller/heater you can even heat a space in cold weather environments. The heat exchangers inside the units are made from corrugated aluminum fins and internally grooved copper tubes. The white ABS casing looks great. Because of its rounded corners it has no water retaining areas favorable to germ development. Units are outfitted with stainless steel screws and show no sharp, cutting edges. Fan Unit Temp Control Upgrades: 1/2 in. Solenoid Valve - Allows or blocks flow of glycol through the fan unit. Needs to be connected to a Controller to function. A filter is recommended to protect the solenoid. 1/2 in. Solenoid Filter- protects the solenoid valve from any particulate or sediment. Glycol Fan Control Unit - Set a specific temperature on this controller and it will open and close the solenoid valve. Solenoid Connection Cable - This 2 meter long cable is required to connect the Solenoid Valve & Control unit. Specifications of MR135: Will cool well insulated spaces up to 3500 cubic feet while drawing 2/3 Ton of cooling power Double Fan Unit (pictured is 3 fan unit) 220V connection required to run fan You will need to connect to your existing glycol system Inlet and Outlet 3/4" Male BSP
A unique alternative to cooling plates. This tube-within-a-tube snake is used to recirculate glycol or cooled water through your wine to keep temperatures down. Can be used in a tank, macrobin, or barrel. The inner tube runs through the middle of the outer shell, but is shorter. Glycol can run through one tube and back through the other, completing the loop.
Snakes are outfitted with 1/2in. male NPT threads on both the inlet and outlet. The inlet is at 90 degrees and the outlet is straight.
.25m Square meter of Cooling Surface.
Ideal for use in an Oak Barrel or Small Tank.
Can also be used for heating.
Optional silicone sleeve for sealing.
Cold stabilization in one barrel or control fermentation temperatures in a 100L tank. With an overall length of 20 in. this little snake can be used to control temperatures in any small batch.
You will need a glycol system or at least a cold or hot water source to connect to the snake.
How it works: This tube-within-a-tube snake is used to recirculate glycol or cooled/heated water through your wine to regulated temperatures. The inner vinyl tube runs through the middle of the corrugated stainless tubing, but is shorter than the stainless tubing. Glycol can run through one tube and back through the other, completing the loop.
Use our custom made Snake Bung to make an air tight seal. Slides over the snake and seals it to the barrel or the traditional air lock hole in a variable volume lid (provided the hole is approximately 1 3/4 in. in diameter.) Or punch a 1 3/4in. hole in any tank or lid.
Snakes are outfitted with 1/2in. male NPT threads on both the inlet and outlet. The inlet is at 90 degrees and the outlet is straight.
1 3/8" diameter. 0.11 m² Surface area.
Can also be used for heating
A unique alternative to cooling plates. This tube-within-a-tube snake is used to recirculate glycol or cooled water through your ferment to keep temperatures down. It can be used in a tank, macrobin, or barrel. The inner vinyl tube runs through the middle of the corrugated stainless tubing, but is shorter than the stainless tubing. Glycol can run through one tube and back through the other, completing the loop.
Snakes are outfitted with 1/2in. male NPT threads on both the inlet and outlet. The inlet is at 90 degrees and the outlet is straight.
1.2 Square Meters of Cooling Surface
Can also be used for heating
Optional silicon sleeve available for sealing
A new & unique alternative to cooling plates. This tube-within-a-tube snake is used to recirculate glycol or cooled water through your ferment to keep temperatures down. It can be used in a tank, macrobin, or barrel. The inner vinyl tube runs through the middle of the corrugated stainless tubing, but is shorter than the stainless tubing. Glycol can run through one tube and back through the other, completing the loop.
Snakes are outfitted with 1/2in. male NPT threads on both the inlet and outlet. The inlet is at 90 degrees and the outlet is straight.
.40m Square meter of Cooling Surface
Ideal for use with an Oak Barrel or Small Tank.
Can also be used for heating.
Optional silicon sleeve for sealing.
Replacement Foam Filled Door for RAPT Fermentation Chamber. This is a direct replacement for the standard door included in the RAPT. Brushed stainless steel with PU foam insulation.
KegLand Part Number: KL15837
