Add a 1.5" TC flange to virtually any vessel! Weldless design Ideal for FTSs and Brew Bucket flat lid pressurized transfers Use with the Pressurized Transfer Fitting FE26 (as shown in pictures) 304 Stainless Construction High heat compatible silicone O-ring Requires TC Clamp and Gasket 42 mm carbide hole saw recommended for installation Please note this product only includes the three pieces displayed in the first photo.
The MTSs is a Heating System Upgrade designed for use with Ss Brewtech’s Infusion Mash Tun. During extended Mash periods or in relatively cold ambient temperatures, the mash will naturally drop in temperature. This system will counteract those temperature drops, and hold a consistent saccharification temperature, helping insure you are making the beer and flavor profiles you planned to produce. The MTSs is a low wattage silicone heater pad, which is bonded to the underside of the 5 degree sloped bottom on your Mash Tun using a strong adhesive backing on the heater pad. The heater is controlled with a 12 volt digital temp controller. You simply set your target temperature and the heater will cycle on and off to maintain your set point. This system is NOT designed for heating water to strike temp and/or step mashing, though it can help with fine tuning your strike water temp those last few degrees and/or maintaining your strike water temp while you are preparing your grist or balancing your water chemistry.
Another high quality intuitive piece of brewing gear from Ss BrewTech, the Ssparge Arm! Simple design, with adjustable height and flow rate, this is a necessary add on for the Ss InfuSsion Mash Tuns.
Incredibly easy to use: Simply choose and thread on a flow rate disk, clip the unit to your mash tun, set the height just above your grain bed, and get brewing!! See the Documents tab above for a more detailed guide to use.
For USE ONLY ON Ss MASH TUNS (10/20 gal)
304 Stainless Steel construction
Designed for gravity feed from HLT
Or hook your own pump / flow control valve
3/8” diameter stainless tubing
3/8" barb on inlet of tubing
Custom silicone handle mount for Ss Mash Tun
Easily adjust height of sparge head up / down
Uniform liquid dispersion fom sparge head
Replacement silicone feet for your Chronical Conical. A must have to keep your stainless steel fermenter level when the original feet get lost or damaged. Pack of 3.
Ss BrewTech's T.C. brewing kettle is made from quality 304 stainless steel and can last you a lifetime of home brewing. This high-quality boil kettle features an aluminum core Tri-Clad bottom to foster even heating and minimize the risk of scorching and allow for the use of induction heating. Tri-Clamp ports have long been the standard in professional brewing, and for a good reason, they're quick, sturdy, and sanitary. The Ss T.C. Brew Kettle now brings this pro-level feature to the home brewer in an affordable package.
The sturdy riveted silicone-coated handles are located on the front and back for easy moving and dumping of the kettle while also allowing for tighter brew stand setup. Just like the original Ss Brew Kettle, the T.C. version features an integrated trub dam into the dip tube to minimize the pickup of trub and hop material during knockout. The result is much clearer wort making its way into your fermenter.
Features:
Tri-Clad bottom
Sanitary TC Ports
Sturdy riveted silicone coated handles
3-piece TC ball valve with trub dam pick-up tube
Lid designed to hang on side of handles
Etched volume markings gals/liters
Induction burner compatible
Included Hardware:
(2) TC Clamps
(2) Silicone Clamp Gaskets
3-piece TC Ball Valve
Dip Tube w/ Trub Dam
Silicone Trub Dam Blade
TC Port Plug
Specs:
Size
Capacity
Diameter
Height
10 gal
10.7 gal
13.8"
16.5"
15 gal
15.7 gal
15.8"
18.9"
20 gal
22.7 gal
17.7"
21.3"
30 gal
31.1 gal
19.7"
23.7"
50 gal
53.0 gal
23.6"
28.3"
Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.
1.5 in. TC sample valve from Ss Brewtech. Uses lever operation and easily disassembles for cleaning.
Features:
Made from 304 stainless steel
Knob/Bonnet operation
Completely sanitary with silicone seal
Easy disassembly for cleaning
Compatible with most sampling coils
The best way to make your own mash tun out of one of your Ss Brew Kettles. These false bottoms are domed and have a central suction point.
Features:
Made from 304 stainless steel
Domed shape
Central suction point
Welded handle
Silicone gasket
Note: These false bottoms are designed for the Ss Brewtech Brew Kettles and will not fit other kettles. They are also not compatible with the Ss Brewtech BME Kettles.
Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.
Chill your beer in the summer and warm your beer in the winter! Temperature control during fermentation is one of the keys to making world class beer at home. It can be difficult to achieve however, often requiring you to have a temperature controlled refrigerator dedicated to fermentation. Now with the FTSs temperature control package and either a Brew Bucket or Chronical, you can maintain perfect fermenting temps all year. This particular unit is designed to work specifically with the 14 gallon Brewmaster Edition Brew Bucket.
The system is elegant and engineered to be as compact and affordable as possible. The FTSs uses a precision digital temperature controller in combination with a 304 stainless steel immersion chiller. The digital controller constantly monitors your beer’s temperature and will activate the very quiet circulation pump to hold the fermentation temperature at your predetermined set point. You can cold crash or lager too! You supply the chill water source, which can be as simple as ice water in a cooler or as involved as glycol from a chiller’s reservoir. We supply the rest of the system. As long time fellow home brewers, this is a system we know many of you have been dreaming about for a long time: advanced temperature control for the beers you make at an affordable price.
Components:
Custom lid w/ 304 SS immersion chiller coil
Pro grade (super quiet) submersible pump
110-240 v power supply
304 SS weldless lid mounted thermowell
Tailored neoprene insulation jacket
Digital temperature controller
Included vinyl tubing
Required from you:
Any type of cooler where you will add water and ice, or frozen jugs, to cool. You will submerse the included pump in the water.
To heat you can use a simple aquarium heater to raise the temperature of the water in the cooler
A 14 gallon Brewmaster Edition Brew Bucket, FE804
Please Note: This Product is an add on for a 14 gallon Brewmaster Brew Bucket, and DOES NOT INCLUDE the brew bucket itself.
Chill your beer in the summer and warm your beer in the winter! Use a chill water source when it's hot or warmed water if it's cold! Temperature control during fermentation is one of the most significant contributors to the flavor of our beers, yet it all too often gets overlooked. This particular unit is designed to work specifically with the Brew Bucket Mini.
Brewers typically have limited the styles of beers they produce to the varying temperatures of the seasons. The system is elegant and engineered, yet it stays true to the heart and soul of us home brewers. The FTSs uses a precision digital temperature controller in combination with a 304 stainless steel immersion chiller. The digital controller constantly monitors your beer’s temperature and will activate the circulation pump (which, by the way, is quieter than a mouse) to hold the fermentation temperature at your predetermined set point. You can crash cool or lager too! You supply the chill water source, which can be as simple as ice water in a cooler or as involved as glycol from a chiller’s reservoir. We supply the rest of the system. As long time fellow home brewers, this is a system we know many of you have been dreaming about for a long time: advanced temperature control for the beers you make at an affordable price.
Features:
Custom lid w/ 304 Ss immersion chiller coil
Pro grade (super quiet) submersible pump
110-240V power supply
304 Ss weldless lid mounted thermowell
Tailored neoprene insulation jacket
Digital temperature controller
Mount your FTSs control unit to the thermowell port of your SS Brewmaster Edition Chronical or Standard Brite Tank!
Features:
Matte Black painted stainless
Mounts on thermowell port
Custom built to fit FTSs digital controllers
This handle is a removable upgrade for the Ss Brite Tanks. It slides onto the TC Flange, allowing for easier lifting with the silicone covered handles. Thick 2 mm SS constuction holds your beer sturdy during movement!
The Ss Brite Tank is already an amazing piece of homebrewing equipment, and paired with a BrewMaster Upgrade Kit, you're one step closer to the ultimate home serving setup. This upgrade kit includes a TC Cap with stainless steel coil for cooling, and a thick Neoprene Jacket to keep the unit insulated! Combine with a Glycol Chiller for a stand alone home serving setup! Only works with 10 Gallon Brite Tank Features: 5 mm thick Neoprene Zippered Jacket Immersion Chiller coil mounted to 6" TC Cap Chiller Coil has 3/8" Hose barbs (matches up with FTSs system tubing!) Includes Hose Clamps. Pair with a Glycol / cooled liquid source, or click here for optional FTSs Temp Control Kit
Set a temperature on the controller, provide a source of chill water for your system, tuck the heater pad underneath the neoprene jacket, plug into the wall and walk away. This system will hold your set temp both when it gets cold and when it gets warm!
This kit is for owners of the Ss standard edition Chronical Half Barrel fermenter that are looking for a two-way switchable controller with both heating and chilling functionality.
Kit contents include:
1x heater pad for Half BBL Chronical
1 x power supply 110-240V and 6A power supply for global use
1 x two-way switchable FTSs controller
1 x flat FTSs lid
1 x chilling coil
1 x lid mounted thermowell
10 feet of vinyl tubing
1 x lid stopper
1 x submersible pump
1 x custom tailored neoprene jacket for Chronical Half BBL fermenter
Digital temp controller displays both C/F
Chill from 0.5-2 degrees F per minute
Custom lid with 304 Ss immersion chiller coil
304 Ss weldless lid mounted thermowell
Accurately monitor and control temps
Set a temperature on the controller, provide a source of chill water for your system, tuck the heater pad underneath the neoprene jacket, plug into the wall and walk away. This system will hold your set temp both when it gets cold and when it gets warm!
This kit is for owners of the Ss standard edition Chronical 14 Gallon fermenter that are looking for a two-way switchable controller with both heating and chilling functionality.
Kit contents include:
1x heater pad for 14 Gal Chronical
1 x power supply 110-240V and 6A power supply for global use
1 x two-way switchable FTSs controller
1 x flat FTSs lid
1 x chilling coil
1 x lid mounted thermowell
10 feet of vinyl tubing
1 x lid stopper
1 x submersible pump
1 x custom tailored neoprene jacket for Chronical 14 gallon fermenter
Digital temp controller displays both C/F
Chill from 0.5-2 degrees F per minute
Custom lid with 304 Ss immersion chiller coil
304 Ss weldless lid mounted thermowell
Accurately monitor and control temps
The Ss Brewtech Whirlpool fitting attaches to the thermometer port, the recirculation port, or another 7/8" hole. Creates a nice whirlpool action that works perfectly with a trub dam to keep out most of the hop matter and other solids from your fermenter. Made from 304 stainless steel. The whirlpool fitting has a 1/2" MPT and comes with 1" x 1/2" bulkhead. Please note this product is intended to be used with a 1/2" FPT ball valve (BE382) on the outside of the kettle. Please see the Whirlpool Fitting Quick Reference Guide below for installation and operation instructions.
This is a 304 stainless steel blow off tube for Ss Brewtech 1/2 barrel Chronical fermenters. Fits perfectly on the 3" TC dome lids and comes with a relief valve built into the cane. 3" TC gasket and clamp not included.
This is a 304 stainless steel blow off tube for Ss Brewtech 14 gallon Chronical fermenters. Fits perfectly on the 3" TC dome lids and comes with a built-in relief valve. The two-piece cane has an outer diameter of 15 mm (approx. 9/16") and 3/8" NPT where they connect. 3" TC gasket and clamp not included.
This Ss Brewtech fitting helps with recirculation in your mash tun. It has a 1/2" FPT on the mash tun side, a 1/2" MPT on the opposite side, and a 1/2" hose barb on the bottom of the tee. Made with 304 stainless steel.
Used along with the Ss recirculation bulkhead, this fitting adds a 3/8" hose barb on your mash tun. It attaches with a 1/2" FPT knurled locking nut and is required if you are using the Ss recirculation manifold. Made from 304 stainless steel and silicone O-rings included.
These chiller coil extensions extend the length of the Ss Brewtech FTSs chiller coil for Brew Bucket and 7 gallon Chronical fermenters. Very useful if you brew partial batches and/or there is a cool ambient temperature forcing you to mostly heat your fermenter. Mounts under the lid to drop the coils further down. Made from 304 stainless steel and leak tested.
A Pressure Relief Valve upgrade or replacement for the Chronical line of fermenters from Ss BrewTech.
Features:
Standard replacement part for Half Barrel
Can be retrofitted to 7 Gal Chronical lid
Releases pressure between 2-2.5 psi
Food grade silicone O-ring
Use Dewalt DWA1783IR step bit for retrofit
For 7/32" inch hole diameter (in lid)
Chill your beer in the summer and warm your beer in the winter! Use a chill water source when it's hot or warmed water if it's cold! Temperature control during fermentation is one of the most significant contributors to the flavor of our beers, yet it all too often gets overlooked. This particular unit is designed to work specifically with the 14 Gallon Chronical Fermentor.
Brewers typically have limited the styles of beers they produce to the varying temperatures of the seasons. The system is elegant and engineered, yet it stays true to the heart and soul of us home brewers. The FTSs uses a precision digital temperature controller in combination with a 304 stainless steel immersion chiller. The digital controller constantly monitors your beer’s temperature and will activate the circulation pump (which, by the way, is quieter than a mouse) to hold the fermentation temperature at your predetermined set point. You can crash cool or lager too! You supply the chill water source, which can be as simple as ice water in a cooler or as involved as glycol from a chiller’s reservoir. We supply the rest of the system. As long time fellow home brewers, this is a system we know many of you have been dreaming about for a long time: advanced temperature control for the beers you make at an affordable price.
Features:
Custom lid w/ 304 Ss immersion chiller coil
Pro grade (super quiet) submersible pump
110-240V power supply
304 Ss weldless lid mounted thermowell
Tailored neoprene insulation jacket
Digital temperature controller
Give your Chronical insulation to help with maintaining fermentation temp and assist with cold crashing. Specifically sized for the 10-clamp version of the 1/2 bbl unit.
Replacement pre-drilled FTSs lid. Included with the the Ss BrewTech FTSs chilling system for the 1/2 bbl Chronical.
Lid only. This does not include the other FTSs components.
