KegLand is a high quality homebrewing equipment brand based out of Australia. We offer a wide variety of their products, from BrewZilla all-in-one system and DigiBoil eletric kettles, to pumps and grain mills. KegLand beer products are an incredible value, as they combine quality craftsmanship with low prices!
KegLand
-
BrewZilla | Replacement Malt Pipe Handle | 65L
Replacement malt pipe handle for the 65L BrewZilla. 3/8" thick. KegLand Part Number: KL29513
$16.49
-
KegLand Quick Swivel Connector | 3/8" Straight Barb | 9.5 mm Duotight Compatible
This straight barb in 3/8" (9.5mm) OD is only compatible with the 1/2" KegLand Quick Swivel Connector Nut. Compatible with 9.5 mm Duotight fittings. Quick Swivel Nut sold separately. KegLand Part Number: KL31578
$3.99
-
KegLand Quick Swivel Connector | 1/2" x 1/4" Straight Barb | 6.35 mm Duotight Compatible
High temp silicone grip provides a cool touch even with hot liquids! Ribbed grips allow quick comfortable tool-free operation Fits all male 1/2" NPT and BSP fittings 6.35 mm Duotight compatible stainless steel barb tail The KegLand Stainless Steel Quick Connectors come with a heavy-duty silicone grip guard allowing comfortable and quick tool-free operation. Specs: Stainless steel and silicone construction Silicone O-ring seal is retained for perfect positioning but is easily cleaned or replaced 1/4" (6.35mm) OD barb tail KegLand Part Number: KL31608
$8.79
-
Temp Twister Lid for Bucket Buddy Fermenters | 65L
This flat lid with pre-drilled holes allows you to easily add a Temp Twister Cooling Coil to your 35L Bucket Buddy fermenter. It also has holes for your stopper & airlock (included with the Bucket Buddy) as well as a Thermowell so you can control the circulation of cooling solution with a Temperature Controller. The lid is also compatible with 65L BrewZillas and DigiBoils. If you're fermenting in the Bucket Buddy with built-in heating element, we recommend plugging the unit into the heating outlet of your temperature controller and leaving the power switch turned on. This will allow the temp controller to provide power to the unit only when heating is needed and it will cut the power as soon as you're back to your set temperature. Using the Bucket Buddy's controller to maintain the heating set temp and using a separate controller to maintain the cooling may result in heating and cooling cycling at the same time. NOTE: The pre-drilled holes are meant for specific sizes of Duotight bulkheads and the stopper included with the Bucket Buddy fermenter. All holes need to be occupied in order to protect your fermentation from outside contaminants. Depending on the placement of the Temp Twister, you might need to shorten the inlet/outlet tubes on the outside of the fermenter using a Pipe Cutter. Lid only. Other accessories must be purchased separately. You Will Also Need: Temp Twister Cooling Coil FermZilla Thermowell Temperature Controller KegLand Part Number: KL28110
$43.99
-
RAPT Fermentation Chamber | Wine Rack
Turn your RAPT Chamber into a highly specialized wine cellar. These shelves are suited to fit wine bottles and the larger champagne bottles. KegLand Part Number: KL25577
$21.99
-
Neoprene Insulating Keg Parka for Oxebar Mono PET Keg | 8L
Keep your beer colder for longer with the insulating neoprene material Prevent dings and scratches during transport with an internal bump cap Easily carry your keg using the removable shoulder strap The zippered design makes it simple to put on and take off Tailormade for the 8L Oxebar Mono PET Keg Keep your beverage colder for longer with the Oxebar Neoprene Jacket. This parka is more than just a cozy sleeve for your keg; it's designed with a rigid internal "bump cap" to prevent those annoying scratches and scuffs that can happen when your keg is being moved around. Made from durable neoprene, this jacket helps maintain the temperature of your beverage, whether you're taking it to a party or just keeping it chilled in the fridge. The Oxebar Neoprene Jacket protects your keg while helping your beer stay crisp and cold. KegLand Part Number: KL42895
$32.99
-
KegLand Cold Plate | 2 Lines
The KegLand Aluminum Cast Cold Plate features an impressive thermal mass with excellent heat absorption characteristics. High conductivity aluminum alloy aids the heat transfer as your beverage travels through the internal stainless steel lines. Inlets and outlets come with standard 1/4" male flare thread so you can easily attach swivel nuts and barbs or Duotight adapters. If you're making a jockey box for backyard cookouts, tailgaters, or camping trips, we highly recommend cold plates over draft coils. Cooling plates are perfect in low volume applications where space is an issue, and the low-profile design leaves plenty of room to store other food or beverages. If you're looking to serve beer at a festival or wedding where the beer might be constantly flowing, we would recommend stainless coils like those featured in the KOMOS Draft Box. Performance Characteristics: With 68°F ambient beer temp, flow rate through the cold plate of 10oz/10 seconds, and 70% coverage of ice in contact with the cold plate, you will be able to reduce the temperature of the liquid as it exits the cold plate to below 39°F with a single pass. If your beer is warmer than 82°F, we would recommend either slowing your flow rate through the cold plate or alternatively loop the two beverage lines together so the liquid passes through the cold plate twice. Specs: Aluminum cast 18 ft. internal lines made from 304 stainless steel 1/4" male flare connections 15" L x 10" W x 1" Thick (2.75" tall at inlet/outlet) Pre-drilled mounting holes Recommended serving pressure - 20-30 psi KegLand Part Number: KL04701
$149.99
-
Flanged Tri-Clamp Gasket | EPDM | 4"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections EPDM gaskets are more resistant to acids and caustic chemicals, and don't show signs of wear as quickly as silicone For 4" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both EPDM and Silicone. EPDM gaskets have a more narrow temperature range than silicone gaskets, but they are more resistant to acids and caustic chemicals. For 4" tri-clamp fittings Made from EPDM Temperature rated from -30°F to 300°F KegLand Part Number: KL45209 Example Image: Updated images coming soon. See the video below to check out the flanged gaskets in action.
$2.79
-
Flanged Tri-Clamp Gasket | Silicone | 1.5"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections Silicone gaskets have a wide temperature range and are recommended for hot side applications For 1.5" tri-clamp connections Flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both Silicone and EPDM. Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 1.5" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F KegLand Part Number: KL44837
$2.19
-
Silicone Stopper | 20mm x 36mm | Solid
This versatile silicone bung is made from a food-grade, lead-free material, making it ideal for use with all food and beverages. Dimensions: Tapered Diameter: 20mm to 36mm (0.78" to 1.41") Solid stopper (no hole) KegLand Part Number: KL12829
$1.99
-
Stainless Tri-Clamp | 3 Piece | 4" Clamp
Double-hinged for easier handling when connecting tri-clamp fittings Textured tightening knob for better grip with wet hands Hang the clamp by the knob on a peg board when not in use This stainless steel tri-clamp features two hinges and folds into three pieces. Some brewers find this style of clamp easier to work with on large equipment that requires a 4" clamp. KegLand Part Number: KL32902
$16.99
-
Replacement Pump for BrewZilla | Gen 3 | 110V
Replacement internal pump for 110-120V Gen 3 BrewZillas. Comes with bare wire. KegLand Part Number: KL05463
$87.99
-
Kegland Equipment Hangers | Adhesive with Stainless post | 4 Pieces
Perfect for mounting Kegland RAPT Cannular Can and Bottle Filler (CAN250), RAPT Temperature Controller (FE971), and Gauge Guard for CO2 Regulators (D1082 & D1175A) Can be used to hang any equipment that has keyhole style cutouts or circular holes for hanging with screws High-quality stainless steel posts resists corrosion in humid brewing environments. Perfect for mounting regulators, manifolds, or tools inside fridge walls where coolant lines might be hidden. Designed for brewers who value a clean, organized workspace, these hangers provide a sturdy mounting point for various draft appliances and accessories without the need for drilling. Particularly useful for some kegland hardware, you can also use these to hang a draft tool, adjustable wrench, etc. Installation Best Practices To ensure a permanent, high-strength bond, please follow these guidelines: Prep the Surface: Thoroughly clean the mounting area with isopropyl alcohol to remove any oils or dust. Temperature Matters: If installing inside a kegerator or keezer, ensure the unit is turned off and at room temperature. The adhesive will not cure properly in cold or damp conditions. Let it Set: For maximum hold, allow the adhesive to cure for at least 24 hours before hanging any equipment or attaching hoses. Most Commonly Used With: RAPT Cannular Can and Bottle Filler (CAN250) RAPT Temperature Controller (FE971) Gauge Guard for CO2 Regulators (D1082 & D1175A) KegLand Part Number: KL50715
$8.99
-
Duotight Mini CO2 Regulator | CGA320 Adapter for CO2 Tanks
Seamless Integration: Specifically designed to bridge the gap between portable regulators and full-sized tanks. Leak-Proof Design: Includes a durable nylon washer to ensure a rock-solid, airtight seal every time. Ultimate Versatility: Compatible with both the Duotight Mini Regulator and the Core 360 Regulator. Looking to carry a massive CO2 supply without the bulk? Pair your duotight Mini Regulator with this high-quality adapter to connect directly to standard CGA320 CO2 tanks. Taking your kegged homebrew on the road has never been more convenient. Simply thread the adapter onto your regulator, then attach the assembly to your CO2 cylinder. It’s the perfect way to make your portable kegging setup even more versatile by utilizing larger, more economical gas sources. KegLand Part Number: KL42024
$9.99
-
Replacement Shuttles for NukaTap® Flow Control Faucet | Gen 2 | Backwards Compatible Retrofit Upgrade Kit
Replacement flow control shuttles for the Gen 2 NukaTap Flow Control faucet. These pieces are only for the flow control apparatus in the faucet, not the NukaShuttle itself. These pieces are backwards compatible with the Gen 1 NukaTap Flow Control model, replacing part numbers 11 and 12 in the diagram image above. KegLand Part Number: KL17817
$6.59
-
NukaTap® Mini Beer Faucet | Wall Mount Shank Kit | 6.35 mm Duotight
Designed specifically for mounting the NukaTap Mini Beer Faucet on any kegerator, keezer, cold room wall, or other flat surface Connect beer line directly to the faucet, reducing the amount of temperature loss to a standard draft shank No spinning faucets. Your tap will remain in a fixed orientation once locked into the collet Easy installation. No need to drill a large hole through your fridge to accommodate a standard 5/8" draft shank Use with 6.35 mm OD EVABarrier draft tubing This shank kit is specifically designed to suit the NukaTap Mini Beer Faucet and will allow you to connect the NukaTap Mini to a cooler box, kegerator, keg fridge, cold room wall or any other flat surface. This wall mount shank kit is for use with 6.35 mm OD EVABarrier. For the shank kit for use with 8 mm OD EVABarrier, see here. New Innovative Shank Design Unlike other shank kits, this kit doesn't use a bulky 5/8" threaded shank. The issue with a standard draft shank is that acts as a heat sink, and due to the fact that most shanks sit inside an insulated wall, this results in a substantial amount of warm beer coming out of the tap before cold beer starts flowing. This results in substantial "first pour foam" effect which wastes beer, can result in sour beer, and ultimately negatively effects the quality of the beverages being served. This new design has the beer line feed all the way directly up to the back of the faucet, greatly reducing the volume of non-refrigerated beer. No Spinning Shanks If you have ever installed a traditional 5/8" long shank, you will know how frustrating it is when you use the faucet and it starts rotating. This new design of shank alternative uses three screws that lock the tap into a fixed position and prevents the taps from rotating. If you loosen the 1/2" stainless tap collet you can still have the flexibility to rotate the faucet to any orientation, but once the collet is tight, interlocking teeth on this shank kit and the NukaTap Mini will hold the tap permanently in the correct orientation. Easy Installation Another advantage compared to standard shanks is that this kit doesn't require you to drill a large 3/4"-1" hole through the wall. As no shank is required, only a hole large enough to accommodate the beer line is required. As a result, an 8mm (5/16") conventional drill bit is all that is necessary for installation. However, if you are concerned about the small amount of beer sitting in the draft line inside the wall not being refrigerated, you can also shell out a larger diameter of foam on the inside of the wall to allow cold air to circulate around the beer line thus reducing the non-refrigerated beer in the line even more. If you wanted to do this the Step Drill Bit is the best tool for the job. Any Wall Thickness Other shank kits will require you to purchase a specific length shank for a specific wall thickness. This new shank alternative will fit any wall thickness. If you have wall thicknesses that are less than 2.7" thick then you can use the included screws that have "snap off" points so you can simply cut the screws down to the desired length. However, if the wall is thicker than 2.7" you can simply purchase a conventional screw from the hardware store and screw the shank kit to your wall. If the substrate is firm enough you may not even need to go all the way through the wall so a common 1-1/4" long screw may be all that is required. Specifications: Beer Line Diameter: 6.35 mm OD EVABarrier Collet and Screw Cover: 304 Grade Stainless Steel O-ring Material: Dual O-ring Silicone/EPDM combination Plastic Mounting: Polyketone (POK) Temperature Range: 14-212°F (-10-100°C) Max Pressure: 150 psi KegLand Part Number: KL32193
$21.99
-
Replacement Seal Kit for KegLand Core 360 Mini CO2 Regulator
Contains the o-rings for the piston, the red inlet washer, MK4 seat assembly o-ring, 2 x barb MFL outlet o-rings and a thumb screw o-ring. For instructions on replacing the seals and/or general maintenance please refer to the product manual below. KegLand Part Number: KL12584
$7.69
-
JoinTech Quick Disconnect (QD) | Auto Shutoff | Dry Break | Female QD x 1/2" BSPT
Prevents leaks and spills when disconnected, ideal for pressurized systems Handles both hot and sub-zero fluids, from hot transfers to sub-zero glycol mixtures (-40°F to 280°F) Made with high-strength, chemically resistant polyketone plastic body, 316 stainless steel spring, and EPDM O-ring for long-lasting performance JoinTech Connectors offer a premium quick-disconnect solution for high and low-temperature beverage handling. These fittings are suitable for a wide range of applications, from hot transfers to sub-zero glycol mixtures. The connectors feature an automatic shut-off valve that prevents flow when disconnected, making them ideal for hoses used with pumps or glycol systems. Features: Durable, UV-stable black design Automatic shut-off valve Vacuum rating of 60 psi Connections: JoinTech Female QD 1/2" Male BSPT Materials: Body: High-strength, chemically resistant polyketone plastic Spring: 316 stainless steel O-ring: EPDM Specifications: Operating pressure: Vacuum to 60 psi Temperature tolerance: -40°F to 280°F (-40°C to 138°C) Flow path: 3/8" KegLand Part Number: KL50739
$9.99
-
Silicone Stopper | 32mm x 48mm | With Hole
This versatile silicone bung is made from a food-grade, lead-free material, making it ideal for use with all food and beverages. Dimensions: Tapered Diameter: 32mm to 48mm (1.25" to 1.88") Hole Diameter: 9mm (0.35") KegLand Part Number: KL12836
$4.99
-
Silicone Stopper | 19.5mm x 28.5mm | With Hole
This versatile silicone bung is made from a food-grade, lead-free material, making it ideal for use with all food and beverages. Dimensions: Tapered Diameter: 19.5mm to 28.5mm (0.76" to 1.12") Hole Diameter: 9mm (0.35") KegLand Part Number: KL41669
$1.59
-
Stainless Bucket Fermenter | Replacement O-ring for Racking Arm
Replacement o-ring for the racking arm included with the KegLand Bucket Buddy stainless fermenter. Single o-ring. If you are replacing both o-rings, you will need to order 2. KegLand Part Number: KL24754
$2.19
-
Replacement Pump for BrewZilla | Gen 3 | 220V
Replacement internal pump for 220-240V Gen 3 BrewZillas. Comes with bare wire. KegLand Part Number: KL03834
$87.99
-
Duotight Push-In Fitting | 8 mm (5/16") x 1/2" BSP
Connect EVABarrier tubing to 1/2" male threads with this Duotight adapter. Compatible with EVABarrier 8 mm OD Tubing. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design: The secret to Duotight's superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary! We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL39819
$3.99
-
Drip Tray | Countertop Drip Tray | Removable Grill | Stainless | 11.8 in.
Keep the top of your kegerator clean with this stainless steel countertop-style drip tray. Perfect for placing underneath a draft tower or 2 faucets mounted side-by-side. Removable grill for easy cleaning. Features 5 pressed locations for drilling through and plumbing the drip tray for draining. Features: Removable grill Made from stainless steel 11.8" L x 6.7" W x 0.6" D Kegland Part number: KL13161
$29.99
-
KegLand | Gas Board for Duotight In-Line Regulators | 4 Output
Keep your draft system dialed in with this regulator gas board for Duotight In-Line Regulators. The gas board can hold up to six regulators, allowing you to monitor and adjust the pressure going to each keg. In the example photo, the high pressure from the gas cylinder is fed to the regulator on the left, and then stepped down from there with the lowest pressure line in the right-most position. The holes for wall mounting the board and the holes for mounting the regulators are pre-drilled for easy installation. Made from food-grade polypropylene plastic. Regulators, fittings, labels, and mounting hardware are not included. For a fully rigged gas board, we recommend the following parts: 4 x Inline Regulators 8 x Rigid 8mm Joiners 3 x Duotight 8mm Tee Pieces 1 x Duotight 8mm Elbow These items can be found below under You Might Also Need. KegLand Part Number: KL17701
$17.99
-
Universal Body Connect for Gas and Bev - Ball Lock
This nifty ball lock post is compatible with both gas and liquid ball lock disconnects. A great way to modify your homebrew kegs so you can daisy chain them together, or hook up your gas line to the bev out dip tube to carbonate your beer faster. It is important to note that due to dimensional differences between gas and liquid posts, this item will not form as snug a fit as a dedicated post for gas disconnects. We do not recommend this to be used as a dedicated gas post. Please note that this is just the post. You will need to purchase the poppet and spring separately. Thread: 19/32-18 Kegland Part Number: KL08662
$10.99
-
Flanged Tri-Clamp Gasket | Silicone | 8"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections Silicone gaskets have a wide temperature range and are recommended for hot side applications For 8" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both Silicone and EPDM. Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 8" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F KegLand Part Number: KL44790
$4.99
-
Tri-Clamp Gasket with Stainless Mesh Screen | 7 Mesh | Teflon | 4"
Teflon gasket with 304 stainless mesh screen for 4" tri-clamp connections. Can be used as a filter screen to trap large particulates passing through T.C. fittings. Often used for distillation to retain activated carbon for filtering neutral spirits or used in pot distillation to retain botanicals in the vapor stream. The screen has a mesh size of 7 which will block particles larger than 2.83mm or 2830 microns. This slightly larger mesh size makes this screen ideal for use in a distillation basket. KegLand Part Number: KL28394
$12.49
-
Perforated Pizza Peel | Square Peel | 12"
The quintessential tool for launching your pizza and removing it from the oven Rather than using a pizza spinner, the square peel can be used to remove the pizza while cooking and rotated by hand Perforations allow excess flour to fall off the pizza base so there's less chance of flour burning and smoking up your oven Perfectly sized for HIZO Pizza Ovens The main purpose of a perforated pizza peel is to get rid of excess flour from the pizza base. But why do you want to get rid of the flour? When you’re baking pizza on hot stone or steel, you don’t want flour on the baking surface because it burns. Fine wheat flours that are most commonly used for baking pizza burn at fairly low temperatures. It’s this flour that causes trouble. Dusting your pizza peel with semolina flour, which can handle higher heat better, can also help. Burnt wheat flour will make the oven smoky and will result in more cleaning work when you’re done baking. The burnt flour tends to stick and can be a real pain to get rid of. Especially on an unglazed pizza stone. And if you’re not able to clean the stone properly, the flour can keep smoking next time you use the stone. Less Contact Surface – Less Sticking A perforated peel has a smaller surface that is in contact with the pizza dough. This means pizza is less likely to stick to a perforated pizza peel. The reason is that the larger the contact surface is, the more friction there will be between the peel and the pizza. And more friction means it is more likely to stick. A smaller contact surface also means that you’ll need less flour when you’re dusting the peel. As noted above, you want as little flour as possible in the hot oven. So in addition to removing more flour from the dough itself, the peel need less flour due to the holes. Perforated pizza peels are also lighter than solid pizza peels, due to less metal on the carrying surface. This will make it easier to use the peel. Less Condensation – Crispier Pizza Crust When you take a hot pizza out of the oven, you may have noticed that water sometimes is formed under the pizza. This moisture makes the pizza less crispy, or even soggy. Using a solid pizza peel may create condensation when the hot pizza meets the cold (room temperature) surface. This is mostly a problem with metal peels since hot air is trapped between the pizza crust and the smooth carrying surface. Condensation happens when this hot air is cooled down to a certain point (it’s dew point), and water drops are created. When you’re using a perforated pizza, on the other hand, you will experience less condensation. The reason is that the holes let the hot air escape through the peel. 12" Square x 31" Long Lightweight aluminum construction. Phillips Head screwdriver required for assembly. KegLand Part Number: KL21869
$54.99
-
Nukatap® Counter Pressure Bottle Filler | Replacement Dip Tube
Replacement telescopic dip tube for the Nukatap Counter Pressure Bottle Filler.
$5.49
-
KegLand Oxebar Mono PET Keg | Replacement Graduation Sticker
Replacement graduation sticker for the Oxebar 5.2 Gallon / 20L PET keg (B286). It is white text displayed over a transparent backing sticker. Please follow the directions on the sticker on how to apply this to your Oxebar tank correctly. Oxebar Keg in photo is not included. KegLand Part Number: KL38010
$4.39
-
A-Style Keg Coupler | German Slider Beer Tap | Stainless Steel Body & Probe | PRV | Beer & Gas Barbs Included
A-Type keg coupler fits most German beer kegs such as Paulaner and Spaten Click-to-engage ergo lever handle Includes 1/4" OD barbs for gas inlet and liquid outlet Barb elbow outlet is ideal for low clearance keg storage and easier line routing For Paulaner or Spaten keg, this is an A-Type keg tap. Also known as a keg coupler, keg tap, coupling, or adapter. Both barbs measure 3/16" ID and 1/4" OD. This model features a pull-ring pressure relief valve (not pictured). This Keg Tap Will Usually Fit: Ayinger Bitburger Pilsner Delirium Tremens (Belgium) Erdinger Hefetrub Weisse Fischer Franziskaner Hefe-Weisse Hacker-Pschorr Weisse Hoegaarden White Isenbeck Krombacher Kronenbourg 1664 Paulaner Spaten Staropramen Victoria Bitter Warsteiner KegLand Part number: KL06057
$58.99
-
BrewZilla | Replacement Silicone Tubing Kit for 25W Pump | Gen 4 | 65L
This is a complete replacement silicone tubing kit for the pump and ball valve tubing on a 65L Gen 4 BrewZilla with 25 Watt Pump. Made from food grade silicone and temperature resistant to 356°F (180°C). KegLand Part Number: KL39772
$15.99
-
HIZO Cast Iron Double-Sided Skillet
Compatible with the HIZO G14 Pizza Oven or any backyard grill! Conveniently pre-seasoned—simply wipe with a wet cloth and pat dry Double-sided with a smooth, flat side and raised grill grooves on the other Raised lips on both sides to keep in the juices and oils Perfect for the HIZO G14 Pizza Oven or your backyard grill, the double-sided griddle and flat skillet plate is the heavy-duty heat-retention cooking utensil you need in your arsenal. Weighing in at a whopping 9 lbs, this thick cast iron plate can really hold the heat! The HIZO double-sided skillet has a flat, smooth griddle side, and raised grill grooves for the other side. Both sides have a raised lip to handle some juices and oil to fry in. It can be moved around easily by the two removable handles in three location points on the plate. Directions for First Use: Conveniently pre-seasoned—simply wipe with a wet cloth and pat dry For super sizzling restaurant-style hot plate, preheat on high for at least 20 minutes Dimensions: 12" x 12" x 1" KegLand Part Number: KL24907
$54.99
-
Replacement Lock Nut for AlcoEngine Still Tops
Replacement lock nut for AlcoEngine Copper Pot Still and Copper Reflux Still.
$6.59
-
Replacement Wrench Set for Cannular Can Seamer
Replacement wrenches that comes included with the Cannular Can Seamer. KegLand Part Number: KL13192
$8.79
-
Single Sided Bead Seal | 2"
This 2" replacement gasket is intended for use with the KegLand Ball Lock Adapter Tapping Head for Sanke Kegs (KEG870). It only has the bead on one side of the gasket and the other side is flat. This gasket can also be used to directly clamp on an AlcoEngine Still Top to a compatible lid with 2" tri-clamp ferrule. It is not intended to be used as a replacement gasket for standard tri-clamp fittings. KegLand Part Number: KL99895
$2.19
-
Replacement PCO38 Tapping Head
Replacement PCO38 tapping head. This is the tapping head only. For the full tapping head assembly see KG520. Comes with PCO38 female threads for attaching to the Oxebar Mono Keg and three PCCO1881 male threaded ports for attaching ball lock caps and PRV. KegLand Part Number: KL20169
$7.69
-
KegLand Ball Lock Quick Disconnect (QD) | Replacement Seal
Replacement seal for barbed or flareed stainless ball lock quick disconnects from KegLand. Compatible with KEG732, KEG734, KEG745, & KEG746.
$1.09
-
Cannular Can and Bottle Filler | WiFi Antenna Upgrade
External WiFi Antenna Upgrade for the Cannular Can and Bottle Filler. If your filler is experiencing connection issues, this antenna will help boost signal reception. Only suitable for the Cannular Can and Bottle Filler (CAN250). Not suitable for other RAPT devices. See here for the Antenna Upgrade Installation Guide. Please Note: Cannular Can and Bottle Filler purchased after 7/1/2025 will come with an upgraded WiFI antenna as standard.
$19.99
-
Brewzilla Sight Glass Connection Kit | Stainless Steel Ball Valve & Elbow
This BrewZilla PPSU sight glass stainless steel ball valve and elbow use radial seal O-rings to form a strong, leak-free connection. Two in the ball valve and two in the bottom elbow. When assembling the sight glass to upgrade your existing Gen 3 or Gen 4 BrewZilla, you will reuse the female camlock x female 1/2" fitting that comes on the recirculation arm, or you need to purchase a separate fitting for the end of your custom build. You will also need plumbers tape or food grade Loctite to assemble the ball valve with the camlock fitting. Rather than purchasing the parts separately, Gen 3 and Gen 4 BrewZillas can be upgraded with one of these sight glass kits. KegLand Part Number: KL33817
$27.49
-
Semi-Automatic Label Applicator Machine for Self-Adhesive Labels | Date Printer | 110V
Designed to streamline your labeling process, saving you time and effort. Apply self-adhesive labels quickly and efficiently. Adapts to various sizes and shapes, making it suitable for labeling bottles, cans, jars, or other containers Accurate and Precise: Achieve professional-looking results every time with consistent label placement and adherence Date Coder automatically prints your programmed packaging date onto the label For some homebrewers, the most satisfying aspects of the brewing process is when you hand someone a bottle or can of your latest creation. At this point, presentation is everything, and that begins with a beautifully packaged beer. Using a 3rd party, you can design your very own adhesive labels for bottles or cans, then apply them with perfection using KegLand's Semi-Auto Label Applicator. This semi-automated compact label applicator machine is suitable for bottles, jars or cans of up to 160mm diameter and is fully adjustable for labeling any cylindrical container. Apply self-adhesive labels to your beer, wine or spirits quickly and easily. This version KegLand's Label Applicator includes a date coder to print the packaging date onto the label. This is generally only needed for commercial applications, and if you'll be using the label applicator for personal use, we would suggest the more affordable option without the date coder (CAN310). Specifications: Power: 110V 60Hz Min Label Thickness: 5μm (0.005 mm) Max Label Height: 150 mm (5.9") Max Label Length/Width: 300 mm (11.8") Max Label Roll Diameter: 280mm (11.02") Max Label Roll Inside Diameter: 76mm (2.99") Max Vessel Diameter: 160 mm (6.2") Label Applicator Speed: 1–3 seconds (varies by label length) Approx. Dimensions: 21.6" L x 9.8" W x 13.7" H Data Coder: Fully adjustable position, automatic operation, date code stamps included KegLand Part Number: KL20329
$1,209.99
-
Replacement Malt Pipe Top Screen for BrewZilla | Probe Hole | Gen 4 | 65L
Specifically designed for maximum strength and rigidity. This redesigned top screen features a hole for the probe of the RAPT Bluetooth Thermometer for monitoring and controlling your BrewZilla Gen 4. KegLand Part Number: KL27373
$38.49
-
EVABarrier Double Wall Draft Tubing | LightShield Black | 3 mm ID x 6.35 mm OD
Easily identify gas and beverage lines with color-coded options—LightShield Black for beverages, Transparent Red for gas EVABarrier's double-walled design with a proprietary inner polymer significantly reduces oxidation and CO2 loss, keeping your beer fresher for longer The ultra-smooth, nearly impermeable inner surface of the tubing prevents bacteria and microbes from adhering, ensuring cleaner beer lines The stiff yet pliable EVA outer barrier makes the tubing kink-resistant and ideal for use with push-in fittings like Duotight and John Guest 3 mm ID size is perfect for mobile draft applications where only a short 3.2 ft. beverage line is needed Easily identify your gas and beverage lines with color-coded draft tubing. LightShield Black EVABarrier is recommended for beverage lines while using Transparent Red for your gas lines, saving you a headache when your draft lines inevitably get tangled up in your draft system. LightShield Black also works perfectly for hydroponic systems as it will block UV and discourage algae growth. If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 3 mm (5/32") ID size is perfect for mobile draft applications or home draft systems where only a short beverage line is needed. Lengths of 3.2 ft. per line are all that you'll need for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 3 mm (1/8") Outer Diameter - 6.35 mm (1/4") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. KegLand Part Number: KL42789
$28.49 - $164.99
-
NukaTap® Mini Beer Faucet | Horizontal Clamp On Assembly
Perfect for mobile draft dispensing with the NukaTap Mini Beer Faucet Clamp onto a picnic bench or folding table—an ideal option for backyard cookouts or concerts in the park Makes for a great temporary shank for weekend getaways, camping, or tailgating This bracket is compatible with table or bench edges that are up to 3.5" thick. It can be adjusted to have the wing nut clamp in either direction, simply unscrew the flange piece from the threaded rod, then unscrew, then thread from the opposing side. Please note: This item does not include the Mini NukaTap or Shank pieces. It is simply the stainless steel bracket. Recommended Accessories: NukaTap Mini Faucet (D1598) Wall Mount Shank Kit w/ 6.35 mm Duotight (D1598D) Self Closing Spring (D1598A) 6.35 mm OD EVABarrier Tubing (D1723C) KegLand Part Number: KL0407
$27.49
-
Replacement Stainless Lever Collar | Intertap® | NukaTap®
Replacement lever collar for Intertap or NukaTap faucets. This beer faucet part threads onto the lever and sits above the friction bonnet. Used to help adjust your tap handle to face forward if it is oriented at an angle when fully threaded onto the faucet lever.
$3.99
-
Brass Hex Nut for Draft Shanks
Replacement brass hex nut for standard beer shanks. KegLand Part Number: KL06286
$4.39
-
Filter Bag for KegLand Wood Basket Press
Mesh bag liner for the KegLand wood basket press. KegLand Part Number: KL39826
$16.49
You have seen 480 out of 549 products