KegLand is a high quality homebrewing equipment brand based out of Australia. We offer a wide variety of their products, from BrewZilla all-in-one system and DigiBoil eletric kettles, to pumps and grain mills. KegLand beer products are an incredible value, as they combine quality craftsmanship with low prices!
This handy part is what you need to connect one side into a standard 9.5 mm Duotight fitting and secure the other side with 1/4" ID tubing using a hose clamp over the tube. We have wide range of stainless stepless hose clamps that you can purchase here. The barb is slightly oversized at 7 mm (0.27") which should provide a tight seal with 1/4" tubing. KegLand Part Number: KL2591
Instant and infinite sparkling water at your fingertips whenever you want it! Benchy connects to your household's water supply, chills, carbonates, and delivers on demand Serve up to 8 gallons of chilled, carbonated water per hour Pair with draft faucets and place it on your counter, or install it under the counter and plumb it to a mounted water faucet See below for detailed installation video Benchy Sparkling is the answer for instant chilled and carbonated water on demand. Simply connect your household water supply and CO2 Cylinder to the unit and receive unlimited sparkling and chilled water from the draft faucets. The chiller is highly efficient with very little power draw while idle and has enough cooling capacity to serve up to 8 gallons of sparkling water per hour. This unit comes without shanks or draft faucets, as it can be used as a countertop unit or installed under your counter and routed to a faucet you install on your counter or kitchen sink. If you plan to use it as a countertop unit, we highly recommend NukaTap Flow Control Faucets. Easy Installation: Plug the Benchy into the wall Fill internal water tank Connect household water supply Connect CO2 Cylinder Pour chilled sparking water. It's that simple and you can be enjoying chilled sparkling water in under 1 hour with this setup and barely any time at all to cool down. Ensure that the unit is installed and operated according to the instruction manual which can be found below. Fully Adjustable The Benchy Sparkling has an integrated digital temp controller so you can control the temperature from 0.5-10°C (33-50°F). You can also vary the carbonation level from 0.5 volumes to over 5 volumes for super bubbly water. Cooling Performance The Benchy Sparkling is able to chill about 5 to 8 gallons of sparkling water per hour (based on ambient water and air temperature of 68°F). To further increase the capacity of this unit, you can pre-chill the water from your household supply line either by a holding tank (ball lock keg) in the fridge or a DraftMaster Chiller. If you pre-chill the water you can more than double the output of the Benchy Sparkling. The reservoir temperature on the Benchy should never be set below 2°C (35°F) as you will run the risk of freezing the water inside the carbonation keg. Specifications: 110V Refrigerant: r600a (80 grams) Cooling Power: 600 watts Power Consumption: 155 watts (idle power consumption less than 5 watts) Capacity: approximately 6.6 gal/hour (based on 68°F ambient temperature) Input Gas: CO2 @ 29-50 psi (Requires 8mm (5/16") OD tubing) Input Water: Must be 15 psi higher than gas pressure (Requires 6.35mm (1/4") OD tubing) Sparkling/Chilled Water Out: Requires 8mm (5/16") OD tubing Dimensions: 18.3" H x 11.4" W x 20.5" D (Excluding sight glass that can be removed) Recommended Accessories: CO2 Gas Cylinder CO2 Regulator EVABarrier 4mm x 8mm Tubing PE Water Line Tubing 6.35mm Duotight In-Line Regulator (0-150 psi) Duotight Reducer - 8mm x 6.35mm 8mm Duotight Check Valve Diverter Valve (check water line connection for the size you'll need) Countertop Installation Recommended Accessories: (2) Short Shanks & Hex Nuts (2) Duotight Adapters - Beer Thread x 8mm (2) NukaTap FC Faucets& Self Closing Springs (2) Tap Handles (of your choice) Tube Cutter Faucet & Shank Wrench KegLand Part Number: KL2068
This stainless steel shuttle can be used to replace the TPV rubber NukaShuttle that comes standard in the NukaTap beer faucet. For users that prefer stainless internal mechanisms in their faucet. You will need to remove the bonnet piece at the handle, pull the handle out and then slide the shuttle piece out.
Compatible with all NukaTap faucets, including Gen 2 Flow Control.
KegLand Part Number: KL35958
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections
EPDM gaskets are more resistant to acids and caustic chemicals, and don't show signs of wear as quickly as silicone
For 8" tri-clamp connections
A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time.
Available in both EPDM and Silicone.
EPDM gaskets have a more narrow temperature range than silicone gaskets, but they are more resistant to acids and caustic chemicals.
For 8" tri-clamp fittings
Made from EPDM
Temperature rated from -30°F to 300°F
KegLand Part Number: KL45193
Example Image: Updated images coming soon. See the video below to check out the flanged gaskets in action.
Convert 1" BSP fittings to 1.5" tri-clamp. Made from 304 stainless steel.
BSP vs. BSPP
BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT.
Kegland Part Number: KL23443
Master the art of pizza cooking with the ultimate tool—the perforated pizza peel!
Spin the pizza for even cooking, lift it higher to flames to cook the top, or shield it from heat to protect the top while the crust cooks
Perforations allows heat through to continue cooking the pizza while using the spinner and also allows excess flour to dislodge from the base
Perfectly sized for HIZO Pizza Ovens
Learning to use a pizza peel and developing your turning skills in the oven is most beneficial and highly recommended. It will take a bit of practice but using this tool will help you manage your pizza while it cooks—and the results will be well worth it!
Pizza peels may come perforated or solid but perforated pizza peels have the benefit of allowing the heat from the pizza stone to cook your pizza as it turns and also allows excess flour to be dislodged from the pizza base. The turning peel can also be used as a handy tool to prevent the top of your pizza from overcooking when needed. You can do this by using the peel to shield the top of your pizza from the flame. The peel can also be used to lift the pizza toward the flame when you need to cook your crust or when your base has cooked but your crusts have not. This procedure allows you to manage the cook of your pizza with more precision.
With some practice, learning to use a turning peel will give you the opportunity to cook your pizza with more precision against the heat. It will also allow you to turn your pizza without burning your fingers and misshaping your round pizza. Plus, don't forget the handle length of your peel. If you are using a pizza oven with a flame close to the front of the oven, you will need to use a long-handled peel to protect your hands.
The size of your pizza oven and the pizza itself will determine the size of your peel. This 8" pizza peel is perfectly sized for the HIZO Pizza Oven.
Approximately 8" round and 24" long.
KegLand Part Number: KL21852
This is a super cool bottle for making yeast starter wort. Mix DME and water to make your wort and then boil in the microwave with the cap off. Remove from microwave, thread on the cap while still hot, and place in refrigerator. Store the wort till you need it. When you are ready to make a starter remove from refrigerator to warm up, pour into a sanitized flask, and add your yeast. Make multiple bottles all at once at store in your refrigerator until needed.
This reagent bottle is made from durable borosilicate perfect for storing anything you need. Borosilicate is great because unlike ordinary glass it won't crack with rapid changes in temperature.
KegLand Item Number: KL04015
Replacement Heavy Duty Wire Shelf for the RAPT Fermentation Chamber.
Weight Rating: 132 lbs (60 kg)
Dimensions: 17.7" W x 16.1" D x 1.1" H (450mm x 410mm x 30mm)
KegLand Part Number: KL15844
This Duotight joiner fitting is compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07016
If you like serving out of commercial kegs but prefer the ease of using ball lock fittings in your draft system, this adapter is for you. Instead of buying additional keg couplers and beer thread to ball lock adapters, you can use this tapping head to go straight from sanke keg to ball lock. To install, remove the keg spear, place the gasket on the keg ferrule with the beaded side facing up, attach the silicone dip tube and place the tapping head on the ferrule, then secure with the 2" tri-clamp.
Be sure to always depressurize the keg before removing the tapping head.
Includes:
Ball Lock Post Lid
2" tri-clamp
Single-side beaded tri-clamp gasket
60 cm silicone dip tube (23.6")
Red 2.5 bar PRV (36 psi)
KegLand Part Number: KL10610
This handy kit contains all the seals needed for a NukaTap Counter Tap Bottle Filler.
Includes:
(1) Bleed Valve Seal
(1) 1/4" Male Thread Seal
(2) Push-in Barb Seal
(3) Gas Purge Valve Seals
The majority of these seals in the NukaTap Counter Pressure Bottle Filler would never normally need to be replaced. But in the event of accidental loss or damage, please replace the seals with the addition of food-grade lubricant to ensure their longevity.
KegLand Part Number: KL27632
This tower shank with Matte Black finish matches perfectly with the NukaTap Stealth Bomber faucet and features a Duotight compatible tailpiece. The 1/4" barb pairs with the Duotight 6.35 mm x 8 mm reducer (DUO10), allowing you to quickly and easily connect 8 mm OD EVABarrier draft line (D1717 & D1718). The Duotight fitting is sold separately and can be found below under "You Might Also Need". Please note these shanks are not compatible with Perlick brand faucets. KegLand Part Number: KL20084
Prevents leaks and spills when disconnected, ideal for pressurized systems
Handles both hot and sub-zero fluids, from hot transfers to sub-zero glycol mixtures (-40°F to 280°F)
Made with high-strength, chemically resistant polyketone plastic body, 316 stainless steel spring, and EPDM O-ring for long-lasting performance
JoinTech Connectors offer a premium quick-disconnect solution for high and low-temperature beverage handling. These fittings are suitable for a wide range of applications, from hot transfers to sub-zero glycol mixtures.
The connectors feature an automatic shut-off valve that prevents flow when disconnected, making them ideal for hoses used with pumps or glycol systems.
Features:
Durable, UV-stable black design
Automatic shut-off valve
Vacuum rating of 60 psi
Connections:
JoinTech Male QD
1/2" Barb
Materials:
Body: High-strength, chemically resistant polyketone plastic
Spring: 316 stainless steel
O-ring: EPDM
Specifications:
Operating pressure: Vacuum to 60 psi
Temperature tolerance: -40°F to 280°F (-40°C to 138°C)
Flow path: 3/8"
KegLand Part Number: KL50746
High temp silicone grip provides a cool touch even with hot liquids!
Ribbed grips allow quick comfortable tool-free operation
Fits all male 1/2" NPT and BSP fittings
9.5 mm Duotight compatible stainless steel barb tail
The KegLand Stainless Steel Quick Connectors come with a heavy-duty silicone grip guard allowing comfortable and quick tool-free operation.
Specs:
Stainless steel and silicone construction
Silicone O-ring seal is retained for perfect positioning but is easily cleaned or replaced
3/8" (9.5mm) OD barb tail
KegLand Part Number: KL31622
This elbow barb makes it easier to route lines and avoid kinks in your tubing. Commonly used for pump inlet/outlets, fermenter blowoffs, or gravity fed transfer lines. Quick Swivel Nut sold separately. Specs: 1/2" (13mm) OD x 1/2" Quick Swivel Nut compatible end Stainless steel KegLand Part Number: KL31660
Replacement table spacer for the Cannular Pro Semi-Auto Can Seamer (CAN110). Suitable for 500mL, 330mL aluminum cans and tin cans.
It is not compatible with the manual seamer model (CAN100).
KegLand Part Number: KL17879
304 cast stainless steel ball lock quick disconnect made for high-durability
White ring above the outer bushing to identify the QD for gas use
Compatible with all ball lock style homebrew kegs
1/4" barb connection
This is Ball Lock Quick Disconnect is constructed from stainless steel for lifetime longevity. 1/4" barb.
This QD is for the Gas In side.
2-1/8" H
Please note: the outer bushing on the disconnect is made from chrome-plated brass. All parts that come into contact with liquid are stainless.
Kegland Part Number: KL02981
Replacement Rocker Switch for BrewZilla / DigiBoil. Compatible with all DigiBoils and Gen 3.1 or older BrewZillas.
Compatible with 110-120V and 220-240V.
KegLand Part Number: KL05968
Double-hinged for easier handling when connecting tri-clamp fittings
Textured tightening knob for better grip with wet hands
Hang the clamp by the knob on a peg board when not in use
This stainless steel tri-clamp features two hinges and folds into three pieces. Some brewers find this style of clamp easier to work with on large equipment that requires a 3" clamp. Direct replacement part to the clamp included on the FermZilla Tri-Conical fermenter.
KegLand Part Number: KL25799
Perfect for serving your craft creations on the go or making a compact home draft system that fits inside your refrigerator
Welded from the inside out using a specialized technique for superior, more sanitary welds compared to similar mini kegs
Interlocking chimes for easy and secure stacking of multiple mini kegs
KegLand's Small Stainless Steel Mini Beer Kegs are ideal for homebrewing small batches and serving your craft creations directly from your home fridge. These compact kegs are designed for convenience and versatility.
Flexible Dispensing and Carbonation
You can naturally carbonate your beer using priming sugars or, for a more controlled approach, force carbonate and serve with the Ball Lock Tapping Head. The Tapping Head features a flexible silicone dip tube, allowing you to dispense beer whether the keg is standing upright or lying on its side. The dip tube will sink and draw liquid from the bottom, allowing you to orient the keg whichever way is more convenient in your refrigerator.
Superior Quality and Durability
KegLand's mini kegs are built to last, undergoing acid bath electrolysis to passivate the stainless steel, making them exceptionally resistant to rust. These are the only mini kegs on the market that are welded from the inside out using a specialized technique. This results in a superior, more sanitary welding finish compared to other mini kegs. When you choose a KegLand mini keg, you're investing in the highest quality available, surpassing the standards of other mini kegs of similar design.
Low2 Lid O-Ring
The sealing cap features an O-ring made of KegLand's special Low2 material which offers vastly improved oxygen barrier properties compared to silicone or EPDM, resulting in your beverage staying fresher for longer.
Expand Your Setup with Accessories
Enhance your mini keg experience with a range of available accessories, including neoprene jackets for insulation and compact tapping systems for easy dispensing.
Stackable with the 4L Mini Keg.
Specs:
2L / 0.52 Gal / 67 fl oz
7.6" High x 5.3" Diameter (195mm x 135mm)
Max Working Pressure: 45 PSI / 3 Bar
Made from 304 Stainless Steel
KegLand Part Number: KL06347
This silicone elbow is a replacement for the elbow provided in the PCO38 Tapping Head Kit. Allowing for a 90° connection between the barb on the yellow liquid plastic carbonation cap and the 6.3 mm OD dip tube provided in the kit. KegLand Part Number: KL26260
Four pack of O-rings for the BrewZilla Sight Glass stainless steel ball valve and elbow.
The PPSU Sight Glass uses radial sealing in order to not leak, even under pressure from a 25W pump. This is a very similar design to the Duotight fittings that also use two O-rings. Incase one breaks, or leaks, there is another to save the day.
KegLand Part Number: KL33824
The HIZO G14 Portable Gas-Fired Pizza Oven is the perfect no-hassle solution to cooking the best homemade pizza outdoors
Fast. Heats to 932°F and cooks a pizza in 1 to 2 minutes
Easy. No assembly required. Built-in gas ignition and adjustable heat control dial for temperature control
Portable. Retractable legs and optional carry bag make it easy to transport and set up—just click the switch and start cooking
14" is the perfect size. 12" ovens are too small and 16" ovens are oversized and twice the price.
Making homemade pizza in your kitchen oven is a tasty and rewarding endeavor, but nothing matches the performance and results you get from a purpose-built pizza oven. Kitchen ovens generally max out around 550°F whereas pizza ovens can reach as high as 1,000 degrees. The ideal way to cook pizza is quickly and at very high temperatures in the 800-900°F range, so if you want to take your homemade pizza game to the next level, a gas-fired pizza oven is the way to go!
The HIZO G14 Pizza Oven is propane powered and ready to use straight out of the box with no bolts or tools required for assembly. Complete with dialed control and gas igniter included as standard—no batteries or matches required! Setup and packing away couldn't be easier thanks to the four stable folding legs.
Includes:
HIZO G14 Pizza Oven
Liquid Propane hose and regulator
Dual Scale Temperature Gauge: 32°F - 932°F (0°C - 500°C)
Ceramic Pizza Stone: 14" x 14" x 3/8"
Recommended Accessories:
Waterproof Carry / Storage Bag (FPE202)
Infrared Laser Thermometer (MT401)
12"or 14" Perforated Pizza Peel (FPE205 / FPE206)
8" Round Pizza Spinner (FPE204)
4" Pizza Cutter (FPE203)
Replacement O-ring for beer faucet tower shanks D1239 and D1242.
This O-ring sits underneath the coupling nut of the shank, behind the teeth where the shank connect to the faucet.
KegLand Part Number: KL88067
This Monotight tee piece is perfect for splitting water or gas lines. Compatible with EVABarrier 6.35 mm OD Tubing. Monotight brings the same superior quality as Duotight push-in fittings but more appropriately sized for applications including water treatment equipment, water filters, reverse osmosis fittings, and more. In addition, they are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL2194
The Duotight Elbow Piece is suitable for 6.35 mm (1/4") PE tubing or most lines with a 6.35 mm outer diameter. Designed for use with stiff PE tubing that is commonly used in water treatment equipment, water filters, reverse osmosis fittings, and other appliances that are directly connected to water lines.
Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. No other push ins on the market have EPDM o-rings.
Features:
Insert tubing and firmly push to connect
Easily release tubing by pushing in the collet
Suitable for both gas & beverage applications
Made from food-grade acetal plastic
O-ring made from highly chemical resistant EPDM
Locking teeth made from stainless steel
Pressure rated to 150 psi
Temperature rated to 212°F (100°C)
Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals.
Kegland Part number: KL18449
Prevents leaks and spills when disconnected, ideal for pressurized systems
Handles both hot and sub-zero fluids, from hot transfers to sub-zero glycol mixtures (-40°F to 280°F)
Made with high-strength, chemically resistant polyketone plastic body, 316 stainless steel spring, and EPDM O-ring for long-lasting performance
JoinTech Connectors offer a premium quick-disconnect solution for high and low-temperature beverage handling. These fittings are suitable for a wide range of applications, from hot transfers to sub-zero glycol mixtures.
The connectors feature an automatic shut-off valve that prevents flow when disconnected, making them ideal for hoses used with pumps or glycol systems.
Features:
Durable, UV-stable black design
Automatic shut-off valve
Vacuum rating of 60 psi
Connections:
JoinTech Female QD
13mm barb (0.51")
Materials:
Body: High-strength, chemically resistant polyketone plastic
Spring: 316 stainless steel
O-ring: EPDM
Specifications:
Operating pressure: Vacuum to 60 psi
Temperature tolerance: -40°F to 280°F (-40°C to 138°C)
Flow path: 3/8"
KegLand Part Number: KL41102
Simply unscrew the normal spout on a NukaTap or Intertap faucet and screw this stout spout in its place to pour your nitro brews. This spout has a creamer/aerator disc inside that strips out the nitrogen gas for a creamier beer. Matches perfectly with the NukaTap Stealth Bomber faucet! For additional disc options, check out the 7-Disc Creamer/Aerator Kit. Stainless steel construction with matte black finish. Kegland Part number: KL21135
Connect EVABarrier tubing to 1/2" male threads with this Monotight adapter. Compatible with EVABarrier 8 mm OD Tubing. Monotight brings the same superior quality as Duotight push-in fittings but more appropriately sized for applications including water treatment equipment, water filters, reverse osmosis fittings, and more. In addition, they are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL18753
Replacement 6mm thick gasket for the 65L Distillation Lid. Note: This 6mm gasket offers an improved fit the Gen 4 BrewZilla and Gen 2 DigiBoil. It is also backwards compatible with Gen 3 and older BrewZillas and Gen 1 DigiBoils. To improve the seal further, we highly recommend using the Adjustable Lid Clamps with the Distillation Lid if your unit does not have them. KegLand Part Number: KL32667
This new American White Oak barrel is made by hand and flamed to a medium toast. A small oak barrel is great for ageing your homebrew, homemade wine or spirits. The exterior is raw unvarnished wood, so take care to keep your barrel in tip top shape. The care guide below will give you instructions on to prepare the barrel for first time use, and also how to keep it hydrated and sealed.
Comes standard with a stainless steel spigot.
Features:
10 L (2.64 gal)
American White Oak
Medium toast
Raw Exterior (Non-Varnished) for easier leak prevention techniques
Stainless Alloy Rings coated in a protective black coating
Food grade reinforced plastic screw in cork
Stainless steel spigot
Barrel Wax Block
Stand included
KegLand Part Number: KL04664
Specifically designed for maximum strength and rigidity. This redesigned top screen features a hole for the probe of the RAPT Bluetooth Thermometer (coming soon) for monitoring and controlling your BrewZilla Gen 4. KegLand Part Number: KL2736
Compact Design: Ideal for tight spaces inside small refrigerators or keezers.
Versatile Routing: Use any port as the inlet to feed the remaining three outputs.
Easy Expansion: Pair with DUO102 plugs to customize the number of active lines.
The Duotight Cross Adapter works perfectly as a simple option for splitting gas lines. Insert your gas line to any of the 8mm Duotight connectors and route outgoing gas lines from the remaining three. If you do not need to use all three outgoing gas lines, simply plug the unused ends with a DUO102 8mm Plug.
High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage.
The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market.
EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free.
No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
KegLand Part Numbers: KL46251
Easily dispense both chilled and carbonated water from a single, elegant tap, making it a perfect match for any under-counter filtration or carbonation system
The tap is designed to work seamlessly with various setups, including keg-based systems for chilled or sparkling water and compact under-counter units like the Benchy Sparkling
Made from high-quality stainless steel, this tap is built to last and provides a clean, modern aesthetic that complements any kitchen or bar counter
This dual-outlet stainless steel tap is perfect for dispensing cold filtered water, sparkling water, or ambient temperature water. It's a great choice for systems like the Benchy Sparkling or other filtered water and reverse osmosis (RO) setups.
This tap is an ideal component for a variety of filtered water systems. We offer it specifically for customers who want to dispense chilled or chilled and carbonated water.
Here are a few ways to use this tap to get chilled or sparkling water:
For chilled water, simply place a ball lock keg in your fridge, run your mains water supply through the keg, and then into this tap.
For chilled and sparkling water, you can use a carbonation reactor lid with a keg. This option lets you chill and carbonate water at the same time.
For a complete under-counter solution, the Benchy Sparkling unit is an excellent choice. You can connect your mains water supply to this compact unit, and it will deliver chilled and carbonated water directly to this tap.
Fits benches/counters up to 1.96" (50mm) thick.
Includes 2 x Duotight 6.35mm push in fittings as standard for connecting to 4mm x 6.35mm PE Water Line.
If you are using this with a Benchy Sparkling you will need to step the line up to 8mm. We would recommend this fitting down the line. (Do not attach to the barbs of the tap, they are too wide to fit without leaking.)
KegLand Part Number: KL23917
Get all of the amazing features and functionality out of your Intertap faucet! This kit includes all of the accessories that can be paired with the Stainless Steel Intertap forward sealing faucet. Whether you want to fill a growler or pour a stout, this faucet does it all. Everything you need to dispense from and maintain your Intertap faucet! This Kit Includes: Stainless Steel Intertap Beer Faucet (D1210) Intertap Stout Spout (D1213) Intertap Growler Filler Spout (D1214) Intertap Ball Lock Spout (D1217) Intertap Self-Closing Faucet Spring* (D1212) Intertap Seal & Gasket Kit (D1215) *Does not include shank.
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections
Silicone gaskets have a wide temperature range and are recommended for hot side applications
For 3" tri-clamp connections
A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time.
Available in both Silicone and EPDM.
Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets.
For 3" tri-clamp fittings
Made from Silicone
Temperature rated from -58°F to 446°F
KegLand Part Number: KL44813
This straight barb in 1/2" (13mm) OD is only compatible with the 1/2" KegLand Quick Connector Swivel Nut. 3/8" (10mm) ID bore. Quick Swivel Nut sold separately. KegLand Part Number: KL31585
NOTE: This accessory is designed exclusively for 3-vessel brewers who want to use the BrewZilla or DigiBoil as a mash tun. It is not meant to be used alongside a malt pipe, and it is not intended to be an upgrade or replacement to the BrewZilla's standard false bottom protection screen.
If you're a 3-vessel brewer and want to use the BrewZilla or DigiBoil purely as a mash tun, this is false bottom will give you more volume compared to mashing with a malt pipe. Designed for use with DigiBoil electric kettles or BrewZilla all-in-one systems. Unlike two-piece false bottoms you may find, this unit is welded together for maximum strength. It will easily withstand as much grain weight as you could possibly fit in the vessel. Features welded handles to easily remove the false bottom when cleaning.
Compatible with 65L DigiBoils and Gen 3/4 65L BrewZillas.
Dimensions:
Diameter: 15.35" (390 mm)
Height: 1.88 (48 mm)
Approximate Dead Space: 1.5 gal (5.7 L)
KegLand Part Number: KL27717
Perfect for serving your craft creations on the go or making a compact home draft system that fits inside your refrigerator
Welded from the inside out using a specialized technique for superior, more sanitary welds compared to similar mini kegs
Interlocking chimes for easy and secure stacking of multiple mini kegs
KegLand's Small Stainless Steel Mini Beer Kegs are ideal for homebrewing small batches and serving your craft creations directly from your home fridge. These compact kegs are designed for convenience and versatility.
Flexible Dispensing and Carbonation
You can naturally carbonate your beer using priming sugars or, for a more controlled approach, force carbonate and serve with the Ball Lock Tapping Head. The Tapping Head features a flexible silicone dip tube, allowing you to dispense beer whether the keg is standing upright or lying on its side. The dip tube will sink and draw liquid from the bottom, allowing you to orient the keg whichever way is more convenient in your refrigerator.
Superior Quality and Durability
KegLand's mini kegs are built to last, undergoing acid bath electrolysis to passivate the stainless steel, making them exceptionally resistant to rust. These are the only mini kegs on the market that are welded from the inside out using a specialized technique. This results in a superior, more sanitary welding finish compared to other mini kegs. When you choose a KegLand mini keg, you're investing in the highest quality available, surpassing the standards of other mini kegs of similar design.
Low2 Lid O-Ring
The sealing cap features an O-ring made of KegLand's special Low2 material which offers vastly improved oxygen barrier properties compared to silicone or EPDM, resulting in your beverage staying fresher for longer.
Expand Your Setup with Accessories
Enhance your mini keg experience with a range of available accessories, including neoprene jackets for insulation and compact tapping systems for easy dispensing.
Stackable with the 5L and 8L Mini Keg.
Specs:
10L / 2.6 Gal / 338 fl oz
19.2" High x 6.8" Diameter (488mm x 175mm)
Max Working Pressure: 45 PSI / 3 Bar
Made from 304 Stainless Steel
KegLand Part Number: KL06385
304 cast stainless steel ball lock quick disconnect made for high-durability
Black ring above the outer bushing to identify the QD for beverage use
Compatible with all ball lock style homebrew kegs
1/4" barb connection
This is a ball-lock type quick disconnect that is constructed from stainless steel for lifetime longevity. 1/4" barb.
This QD is for the Bev Out side. See here for the Gas In QD.
2 1/8" H
Please note: the outer bushing on the disconnect is made from chrome-plated brass. All parts that come into contact with liquid are stainless.
Kegland Part Number: KL02998
This Duotight tee fitting is compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL07023
Replacement internal seal for Stainless Carbonation and Line Cleaning Ball Lock Quick Disconnects. Only the stainless steel ball lock caps require these seals (KG50 & KG502). They are not needed for the Red & Yellow plastic versions. Comes in pack of 5. KegLand Part Number: KL21272
This elbow fitting has a 9.5 mm Duotight connection and a Duotight-compatible 3/8" OD barb. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL18432
Comes with a back nut, plastic collar, hex nut, and 8 mm Duotight Adapter compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Requires a 1" hole saw for installation. When set in place, the shank will only have about 4-1/2" of length to pass through your wall or fridge door, due to the length of the collar and back nut.
Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling.
Dimensions:
7-1/8" - Total Length (Tip to Tip)
6" - Shank Length (Without Nut & Barb)
5" - Thread Length
4-1/2" - Pass Through Length
Kegland Part number: KL11952
Maximize the purity of your distillate with high density spiral prismatic packing
Prismatic spiral shape designed to maximize surface area
Large spiral prismatic packing recommended for 4" diameter or larger columns
Take your distillation to the next level with super high density spiral prismatic packing. The packing maximizes the purity of the collected distillate from your reflux still, ensuring the best possible product is collected. The prismatic spiral shape is designed to maximize its surface area helping to separate out fractions in your reflux, resulting in a highly pure and neutral end product. It is not recommended for use with pot stills when producing flavored spirits.
Large spiral prismatic packing is recommended for 4" diameter or larger columns. Standard size packing is recommended for smaller columns home-sized columns.
Note: We recommend soaking and washing the SPP before its first use with a 50:50 mix of vinegar or citric acid and warm to hot water to remove all manufacturing oils.
Sizing: The SPP is approximately 3.58mm x 5.81mm.
KegLand Part Number: KL32704
Elevate your brewing game with the 220V 26 Gallon Gen 4 BrewZilla. This cutting-edge system combines more power & capcity with innovative features like wireless connectivity via WiFi & Bluetooth, allowing you to heat faster while you control and monitor your brew day, ensuring precision, convenience, and exceptional beer batch after batch!
WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal
The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench
Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter
Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency
Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp
The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve
Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps
More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet
WiFi/Bluetooth Enabled RAPT Controller
The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen.
But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability.
And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer!
But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings.
Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road.
Concave Base with Center Draining
Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind.
Ultra Low Watt Density Elements
The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy.
Heat Exchanger Dish
The 100L BrewZilla comes standard with the Heat Exchanger Dish which redirects the flow of wort so that it spends more time exposed to the heating elements before reaching the center drain at the bottom of the kettle and being recirculated. Due to the concave bottom and central draining hole on the Gen 4 BrewZilla, recirculating wort will pass through the malt pipe and then down through the boiler false bottom following the path of least resistance. This can cause wort to make a B-line for the drainage hole and reduce the wort's exposure to the unit's heating elements. With the HED installed, wort will be directed to the edge of the BrewZilla base and pass over the elements for a longer period and reduce the time needed to heat to your set temperature. An optional accessory for the smaller units, but included as standard on the 100L BrewZilla.
Easy Access Built-In Pump
The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet.
If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer.
MoreBeer!'s Final Word
We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included.
Features:
Gen 4.1
Stainless steel construction
26.4 gallon total capacity with a finished beer output of 15-20 gallons
WiFi/Bluetooth Enabled RAPT digital temperature controller
Automatic step mashing with 6 programmable stages
220-240V power
NEMA L6-30P Plug
Requires NEMA L6-30R receptacle
Draws 30 amps. Ask your electrician if you need to oversize the circuit
(3) 2,200W heating elements
Stainless steel 1/2" ball valve for gravity draining or transferring via pump
Heat exchanger dish included
Stainless steel malt pipe/basket
Stamped in volume markers
Glass lid
Adjustable lid clamps (do not use with glass lid in place - see below)
Magnetic drive pump for recirculation, transfers, and cleaning
Recirculation arm
PPSU sight glass
Bottom handle for easy lifting and pouring
Rubber feet
Temperature reads in °F or °C
Approximately 36" H (with recirculation arm) x 20.5" D (boiler only)
Recommended max. grain bill: 41.5 lbs
AlcoEngine Still ready with the purchase of a Distillation Lid
Pump Specs:
Max Capacity: 5 gal/min
Max Head: 11.15 ft.
Voltage: 220–240V-AC
Frequency: 50–60Hz
Power: 25 watts
Input/Output: 13mm barb
You Will Need:
2' of H985 1/2" ID Silicone tubing for sparging and draining.
Wort Chiller for cooling
We recommend either of the below counterflow chillers
Copper Counterflow Chiller (WC130)
BrewBuilt® Stainless Tri-Clamp Counterflow Chiller (WC140)
KegLand Part Number: KL32803
Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos.
Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe.
Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged.
Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.
35L (110V)
35L (220V)
65L (220V)
100L (220V)
10 ft.
14 Gauge
14 Gauge
12 Gauge
10 Gauge
25 ft.
14 Gauge
14 Gauge
12 Gauge
10 Gauge
50 ft.
12 Gauge
12 Gauge
10 Gauge
8 Gauge
RAPT Gen 4 BrewZilla | User Manual
It is really THAT easy to make good beer at home?+
YES! If you can follow a recipe and keep clean, there is nothing stopping you from making great beer in your home - beer you can be proud of and your friends will love! The MoreBeer! mission is to provide reliable equipment and quality ingredients that make the home brewing experience successful and satisfying. We'll get you started in home brewing the way we wish we had been started.
