Hardware and Fittings

Dump out the ice slurry from your jockey box without dumping out your draft coils Designed to pair with KegLand's Square Draft Coils Use the bracket holes as a guide for where to drill your shank holes These specially designed shank brackets from KegLand are a great accessory to pair with the Square Draft Coils for your custom jockey box build. The retention brackets will secure the coils in place so they don't come spilling out when you empty the ice slurry from your jockey box after use. Use the brackets as a guide to mark where to install your draft shanks, then mount them above the square coils and secure in place with the shank hex nuts.  KegLand Part Number: KL40440

Read more less

Add the convenience of quick disconnects to your commercial sanke couplers. The K-Lok QD system will allow you to easily connect and disconnect your draft lines from your keg coupler with no spilling or loss of gas. This K-Lok Male x Male Beer Thread (5/8" BSP) is designed to be attached to your gas line and then connected to the K-Lok Female fitting attached to your keg coupler's gas in port. The built-in check valve prevents gas from draining out of your line when it's disconnected so it's a dry break. Draft lines can be connected to the Male Beer Thread end using a Duotight Adapter for EVABarrier tubing or Hex Nut & Tailpiece for other draft tubing. KegLand Part Number: KL04923  

Read more less

Add the convenience of quick disconnects to your commercial sanke couplers. The K-Lok QD system will allow you to easily connect and disconnect your draft lines from your keg coupler with no spilling or loss of gas. This K-Lok Male x Male Beer Thread (5/8" BSP) is designed to be attached to your beverage line and then connected to the K-Lok Female fitting attached to your keg coupler's bev out port. The built-in check valve prevents liquid from draining out of your beer line when it's disconnected so it's a dry break. Draft lines can be connected to the Male Beer Thread end using a Duotight Adapter for EVABarrier tubing or Hex Nut & Tailpiece for other draft tubing. KegLand Part Number: KL04930  

Read more less

This ball valve with male and Female Beer Thread (5/8" BSP) is incredibly handy for those wanting to shut off flow of liquid and gas lines on keg couplers or shanks. Highly recommended if you are disconnecting your coupler and not re-attaching to another keg immediately. Made from 304 stainless steel. Kegland Part number: KL00406

Read more less

Replacement gaskets and o-rings for German Slider (A-type) keg taps. KegLand Part Number: KL12331

Read more less

Replacement brass hex nut for standard beer shanks. KegLand Part Number: KL06286

Read more less

Replace a broken knob on your CO2 tank, or keep one on hand as a spare. Fits on Kegland CO2 tanks. This is the knob only. Does not included CO2 tank or any related hardware. KegLand Part Number: KL30625

Read more less

Give your beverage the absolute best protection from oxygen staling with KegLand's Low2 O-rings! Made from a special blend of materials, these gaskets offer vastly improved oxygen barrier properties compared to Silicone or EPDM The result is your beverage staying fresher for longer! Compatible with KegLand's 20L Oxebar Mono PET Keg These seals replace the red O-ring seal inside the 20L Oxebar keg lids. What is Low2? Low2 O-rings are the new golden yellow standard of homebrew kegs brought to you by KegLand. Why? Because of their unique composition (Synthetic M-Class and Cross-Linked Elastomers), they have superior oxygen barrier properties than that of the previous silicone O-rings. This results in your beverage staying fresher for longer. The same Low2 O-ring material was independently tested on 5-gallon stainless steel kegs by GunnLab, an Australia-based plastic packaging testing laboratory. See below for a printout of the test results. KegLand Part Number: KL38003

Read more less